首页 > PPD-C4N1R-P

PPD-C4N1R-P

更新时间：2025-07-09 22:50:47
品牌：MSYSTEM
描述：Plug-in Signal Conditioners M-UNIT

PDF下载

中文翻译

免费 PCB/SMT

PPD-C4N1R-P 概述

Plug-in Signal Conditioners M-UNIT

PPD-C4N1R-P 数据手册

通过下载PPD-C4N1R-P数据手册来全面了解它。这个PDF文档包含了所有必要的细节，如产品概述、功能特性、引脚定义、引脚排列图等信息。

PDF下载
MODEL: PPD  
Factory setting  
Plug-in Signal Conditioners M-UNIT  
■ PULSE INPUT SETTING  
•Dry Contact  
PULSE ISOLATOR  
Input  
Semiconductor contact  
(built-in excitation)  
Filter  
W/O (without)  
2 V  
Threshold 0 – 15 V  
Hysteresis 0 – 5 V  
Functions & Features  
0.5 V  
• Galvanically isolating pulse rate signals  
• Input frequency = output frequency  
• Various outputs (relay, open collector and voltage pulses)  
• Excitation  
•Voltage pulse  
Input waveform  
Input coupling  
Input amplitude  
Offset  
Square  
DC  
• Isolation up to 2000 V AC  
• High-density mounting  
0.5 – 50 Vp-p  
≤ 50 V  
Filter  
W/O (without)  
1/2 amplitude  
0.5 V  
Threshold 0 – 15 V  
Hysteresis 0 – 5 V  
Typical Applications  
• Isolating field pulse signals in order to reduce noises  
• Changing e.g. dry contact signal to e.g. 5 V signals  
•5 V voltage pulse  
Filter  
W/O (without)  
W/O (without)  
50  
(1.97)  
•12 V, 24 V voltage pulse  
Filter  
•2- wire current pulse  
ON current (H) 0 – 25 mA  
OFF current (L) 0 – 25 mA  
Filter  
80  
(3.15)  
14.5 mA  
9.5 mA  
W/O (without)  
127  
(5)  
■ SETTINGS FOR PULSE OUTPUT  
mm (inch)  
Output pulse width  
50 ms  
[1] INPUT  
MODEL: PPD–[1][2][3][4][5]–[6][7]  
A: Dry contact  
B: Voltage pulse (Specify sensitivity)  
C: 5 V pulse (sensitivity 2 V)  
D: 12 V/24 V pulse (sensitivity 5 V)  
H: Two-wire current pulse  
ORDERING INFORMATION  
• Code number: PPD-[1][2][3][4][5]-[6][7]  
Specify a code from below for each of [1] through [7].  
(e.g. PPD-D4A3N-K/Q)  
• Frequency range (e.g. 0 – 10 kHz)  
• Output pulse width (e.g. 75 msec.)  
Use Ordering Information  
[2] EXCITATION  
1: 5 V DC @ 120 mA  
4: 12 V DC @ 60 mA  
7: 24 V DC @ 25 mA  
Sheet (No. ESU-1370). Default setting (table below) will be  
used if not otherwise specified.  
• Specify the specification for option code /Q  
(e.g. /C01/S01)  
[3] OUTPUT  
A: Open collector (max. 100 kHz)  
M: 5 V pulse (max. 100 kHz)  
N: 12 V pulse (max. 100 kHz)  
P: 24 V pulse (max. frequency 50 kHz)  
H: High power photo MOSFET relay (max. 20 Hz)  
( ) = Max. frequency  
[4] OUTPUT PULSE WIDTH  
1: Equal to the input  
3: One-shot output (std. pulse width 50 msec.)  
(Specify when optional pulse width is required.)  
PPD SPECIFICATIONS  
ES-1370 Rev.13 Page 1/5  
http://www.m-system.co.jp/  
MODEL: PPD  
the manual for adjustment.  
■ Dry Contact  
[5] OUTPUT LOGIC  
N: The same as the input  
R: Inverted  
Max. frequency: 100 kHz  
Detecting Conditions  
Exc. code: 1  
[6] POWER INPUT  
AC Power  
Sensing: 5 V DC / 0.5 mA  
Detecting level:  
K: 85 – 132 V AC  
OFF: ≥ 2.25 V / ≥ 8.2 kΩ  
ON: ≤ 1.75 V / ≤ 5.3 kΩ  
Exc. code: 4  
(Operational voltage range 85 – 132 V, 47 – 66 Hz)  
DC Power  
S: 12 V DC  
Sensing: 12 V DC / 1.2 mA  
Detecting level:  
(Operational voltage range 12 V ±10 %, ripple 10 %p-p max.)  
R: 24 V DC  
OFF: ≥ 2.25 V / ≥ 2.3 kΩ  
ON: ≤ 1.75 V / ≤ 1.7 kΩ  
Exc. code: 7  
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)  
V: 48 V DC  
(Operational voltage range 48 V ± 10 % , ripple 10 % p-p max.)  
P: 110 V DC  
Sensing: 16 V DC / 2.4 mA  
Detecting level:  
(Operational voltage range 85 – 150 V, ripple 10 %p-p max.)  
OFF: ≥ 2.25 V / ≥ 1 kΩ  
ON: ≤ 1.75 V / ≤ 0.8 kΩ  
Sensing voltage means the excitation supply to the sensor  
and the current value indicates that at shortcircuit.  
Detecting level means the threshold used to determine ON  
or OFF status of the pulses and the resistance values  
indicated that of the sensor.  
[7] OPTIONS  
blank: none  
/Q: With options (specify the specification)  
SPECIFICATIONS OF OPTION: Q (multiple selections)  
COATING (For the detail, refer to M-System's web site.)  
/C01: Silicone coating  
■ Voltage Pulse  
Maximum frequency: 100 kHz  
• Customised pulse: Specify DC offset and amplitude.  
Waveform: Square or sine  
/C02: Polyurethane coating  
/C03: Rubber coating  
Input impedance: ≥ 10 kΩ  
TERMINAL SCREW MATERIAL  
/S01: Stainless steel  
Input amplitude: 0.5 – 50 Vp-p  
Max. voltage between input terminals: 50 V  
• 5 V, 12 V, 24 V Pulse  
Waveform: Square or sine  
GENERAL SPECIFICATIONS  
Construction: Plug-in  
Input impedance: ≥ 10 kΩ  
Detecting level  
Connection: M3.5 screw terminals  
5 V Pulse: V  
12 V / 24 V Pulse: V  
(V – V ≥ 500 mV)  
H
≥ 2.25 V, V  
L
≤ 1.75 V  
≤ 4.75 V  
Screw terminal: Chromated steel (standard) or stainless  
steel  
H
≥ 5.25 V, V  
L
H
L
Housing material: Flame-resistant resin (black)  
Isolation: Input or sensor exc. to output to power  
DIP SW1 & SW2: Used for input spec. setting  
Input monitor (PL1): Red LED blinks when pulse input  
Input monitor (PL2): Not used  
■ Two-wire Current Pulse  
Max. frequency: 100 kHz  
Input resistance: receiving resistor 100 Ω  
Input range: 0 – 25 mA  
Hi/Lo level: ≤ 9.5 mA for Lo, ≥ 14.5 mA for Hi  
■ Voltage pulse waveform  
Excitation adjustment: 5 – 24 V DC  
Input pulse sensing: DC coupled standard or AC coupled  
Input filter: None, 10 ms (for chattering), 0.1 ms (for noise),  
selectable with DIP switch  
Volts  
50V max.  
Amplitude  
Vinp-p  
INPUT SPECIFICATIONS  
Excitation: Shortcircuit protection; approx. 440 mA at  
DC Offset  
shortcircuit  
t
Pulse width time requirement: ≥ 5 μsec.  
The detecting levels shown below are default value. Refer to  
PPD SPECIFICATIONS  
ES-1370 Rev.13 Page 2/5  
http://www.m-system.co.jp/  
MODEL: PPD  
■Voltage pulse (example)  
PERFORMANCE  
Response time  
Volts  
Open collector or voltage pulse: the output is delayed at  
both pulse rise and fall by 3 μsec. each. The delay could be  
much longer for certain types of load for open collector.  
High power photo MOSFET relay: the output is delayed by  
10 msec. at the rise, by 3 msec. at the fall.  
VH  
VL  
Amplitude  
Vinp-p  
Sensitivity Level  
0V  
t
Insulation resistance: ≥ 100 MΩ with 500 V DC  
Dielectric strength: 2000 V AC @1 minute (input to output  
to power to ground)  
ON  
OFF  
Input Monitor LED  
OUTPUT SPECIFICATIONS  
■ High Power Photo MOSFET Relay  
Maximum frequency: 20 Hz  
• Rise time: 5 msec.  
• Sink time: 3 msec.  
Rating: 120 V AC or 120 V DC @ 200 mA (resistive load)  
On resistance: 3 Ω  
■ Open Collector  
Maximum frequency: 100 kHz  
50 V DC @ 50 mA (resistive load)  
Saturation voltage: 0.5 V DC  
■ Voltage Pulse: Rating (5, 12 or 24 V) ±10 %  
Maximum frequency: 100 kHz (50 kHz for 24 V)  
Load resistance: ≥ 1.2 kΩ  
Low level: ≤ 0.5 V  
OUTPUT PULSE WIDTH  
■ Equal to the input: Output waveforms have the same  
period and duty ratio as those of input waveforms (when DC  
coupled).  
■ One-shot Output  
The PPD detects a pulse sink and outputs [input pulse width  
±20 %]; 50 msec. standard  
Note: 2 types of one-shot detection are available: pulse rise  
or sink. Refer to the table on the "Output Logic" section and  
specify when ordering.  
Optional pulse width: 30 μsec. – 300 msec.  
INSTALLATION  
Power consumption  
•AC: Approx. 6 VA  
•DC: Approx. 6 W (230 mA at 24 V)  
Operating temperature: -5 to +60°C (23 to 140°F)  
Operating humidity: 30 to 90 %RH (non-condensing)  
Mounting: Surface or DIN rail  
Weight: 200 g (0.44 lb)  
PPD SPECIFICATIONS  
ES-1370 Rev.13 Page 3/5  
http://www.m-system.co.jp/  
MODEL: PPD  
EXTERNAL VIEW  
Note: This unit is factory calibrated according to the Ordering Information. If you need to change hardware setting, refer to the  
instruction manuals of the transmitter.  
Input Monitor LED PL2  
Sensitivity Adj. (V  
L
)
(not used, always ON)  
Input Monitor LED PL1  
Sensitivity Adj. (V  
H
)
SW1  
SW2  
8
7
6
5
4
3
8
7
6
5
4
3
2
1
2
1
O
N
O
N
Fixed to the above  
setting (except No. 3)**  
Set each switch according  
to the table below.  
(front cover open)  
Sensor Excitation Adj.  
OUTPUT LOGIC  
VOLTAGE PULSE or  
INPUT WAVEFORM  
DRY CONTACT  
OFF  
2-WIRE CURRENT PULSE  
H
OUTPUT WAVEFORM  
L
ON  
H
H
No pulse width conversion  
L
L
One-shot, detecting input pulse rise  
H
H
Non  
Inverted  
L
L
One-shot, detecting input pulse drop  
H
H
L
L
VOLTAGE PULSE  
H
H
No pulse width conversion  
L
L
One-shot, detecting input pulse rise  
H
H
Inverted  
L
L
One-shot, detecting input pulse drop  
H
H
L
L
OFF  
OFF  
No pulse width conversion  
ON  
ON  
One-shot, detecting input pulse rise  
OFF  
OFF  
Non  
Inverted  
ON  
ON  
One-shot, detecting input pulse drop  
OFF  
OFF  
OPEN COLLECTOR  
ON  
ON  
or  
OFF  
OFF  
POWER PHOTO MOSFET RELAY  
No pulse width conversion  
ON  
ON  
One-shot, detecting input pulse rise  
OFF  
OFF  
Inverted  
ON  
ON  
One-shot, detecting input pulse drop  
OFF  
OFF  
ON  
ON  
The pulse width in one-shot means the bold lined section of a pulse waveform.  
PPD SPECIFICATIONS  
ES-1370 Rev.13 Page 4/5  
http://www.m-system.co.jp/  
MODEL: PPD  
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)  
CLAMP  
(top & bottom)  
7.8 (.31)  
DIN RAIL  
35mm wide  
6
5
4
3
2–4.5 (.18) dia.  
MTG HOLE  
15 (.59) deep  
7
8
1
2
8–M3.5  
SCREW  
50 (1.97)  
107 (4.21)  
127 (5)  
40 (1.57)  
50 (1.97)  
[3.3 (.13)]  
• When mounting, no extra space is needed between units.  
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM  
Isolation  
Waveform  
Shaper  
Output  
Driver  
+
–
3
4
5
6
One-Shot  
*
1
2
7
8
+
INPUT  
OUTPUT  
POWER  
–
SENSOR EXCITATION  
+
Excitation  
Supply  
U(+)  
V(–)  
VOLTAGE ADJ.  
Base Socket  
* Provided only when the one-shot output is specified.  
Note: With 24V excitation and dry contact input, the voltage across the  
terminals 3 – 4, divided in the waveform shaper, is of approx. 16V.  
Input Connection Examples  
Output Connection Examples  
■ Dry Contact  
■ 2-Wire Current Pulse  
• Built-in Excitation  
■ Open Collector  
■ Voltage Pulse  
100  
Ω
+
–
–
+
3
4
5
–
+
3
4
5
1
2
+
–
+
–
1
2
+
–
+
–
2-WIRE  
PICK-UP  
Vsns  
Vsns  
PWR  
10k  
Ω
■ Power Photo MOSFET Relay  
• AC Powered  
Relay or  
Counter Coil  
■ Voltage Pulse  
• External DC Supply  
1
2
100  
Ω
Varistor or Spark  
Quenching Circuit  
+
–
–
+
3
4
5
–
+
3
4
5
LOAD  
2-WIRE  
PICK-UP  
DC SUPPLY  
U
Vsns  
Vsns  
• DC Powered  
PWR  
+
–
Relay or  
Counter Coil  
1
2
Spark Quenching  
Diode  
LOAD  
Specifications are subject to change without notice.  
PPD SPECIFICATIONS  
ES-1370 Rev.13 Page 5/5  
http://www.m-system.co.jp/  

PPD-C4N1R-P 相关器件

型号 制造商 描述 价格 文档
PPD-C4N1R-P/Q MSYSTEM Plug-in Signal Conditioners M-UNIT 获取价格
PPD-C4N1R-R MSYSTEM Plug-in Signal Conditioners M-UNIT 获取价格
PPD-C4N1R-R/Q MSYSTEM Plug-in Signal Conditioners M-UNIT 获取价格
PPD-C4N1R-S MSYSTEM Plug-in Signal Conditioners M-UNIT 获取价格
PPD-C4N1R-S/Q MSYSTEM Plug-in Signal Conditioners M-UNIT 获取价格
PPD-C4N1R-V MSYSTEM Plug-in Signal Conditioners M-UNIT 获取价格
PPD-C4N1R-V/Q MSYSTEM Plug-in Signal Conditioners M-UNIT 获取价格
PPD-C4N3N-K MSYSTEM Plug-in Signal Conditioners M-UNIT 获取价格
PPD-C4N3N-K/Q MSYSTEM Plug-in Signal Conditioners M-UNIT 获取价格
PPD-C4N3N-P MSYSTEM Plug-in Signal Conditioners M-UNIT 获取价格

PPD-C4N1R-P 相关文章

  • 小米 AI 眼镜技术亮点：双芯架构助力智能穿戴跨越发展
    2025-07-11
    17
  • AI 芯片风云：台积电能否超越英伟达成新霸主？
    2025-07-11
    15
  • 锁存型霍尔 IC：原理、应用大揭秘
    2025-07-11
    17
  • HBM 角逐：定制化、混合键合等技术成竞争关键
    2025-07-11
    13

    • 热门型号

  • 1N5930
  • 1N5942B
  • 1N4001
  • MBR3050CT
  • RTA02-8D
  • 4116T
  • 5KP43A/4
  • 1N5260A
  • MC79L05
  • BZX85C30
  • 9510-G
  • W2PE-54WZ-P
  • 1N6063
  • 2SA673
  • 20IMX35
    • Hi,有什么可以帮您？ 在线客服 或 微信扫码咨询
  • 概述
  • 数据手册
    • 2025 ICPDF网 联系我们和版权申明:QQ 272164286