SVB-J9-R/K 概述
Plug-in Signal Conditioners M-UNIT
SVB-J9-R/K 数据手册
通过下载SVB-J9-R/K数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载MODEL: SVB
GW: -1 – +1 mA DC (Input resistance 1000 Ω)
Plug-in Signal Conditioners M-UNIT
FW: -10 – +10 mA DC (Input resistance 100 Ω)
Z: Specify current (See INPUT SPECIFICATIONS)
Voltage
SIGNAL TRANSMITTER
(wide-output)
1: 0 – 10 mV DC (Input resistance 10 kΩ min.)
15: 0 – 50 mV DC (Input resistance 10 kΩ min.)
16: 0 – 60 mV DC (Input resistance 10 kΩ min.)
2: 0 – 100 mV DC (Input resistance 100 kΩ min.)
3: 0 – 1 V DC (Input resistance 1 MΩ min.)
4: 0 – 10 V DC (Input resistance 1 MΩ min.)
5: 0 – 5 V DC (Input resistance 1 MΩ min.)
6: 1 – 5 V DC (Input resistance 1 MΩ min.)
4W: -10 – +10 V DC (Input resistance 1 MΩ min.)
5W: -5 – +5 V DC (Input resistance 1 MΩ min.)
0: Specify voltage (See INPUT SPECIFICATIONS)
Functions & Features
• Converts a DC input into a standard process signal
• Isolation up to 2000 V AC
• Fast response type available
• LCD meter
• Max. 30 V output available
• Load resistance 1500 Ω (20 mA output)
• High-density mounting
Typical Applications
• Isolation between control room and field instrumentation
[2] OUTPUT
Current
50
(1.97)
A: 4 – 20 mA DC (Load resistance 750 - 1500 Ω)
B: 2 – 10 mA DC (Load resistance 1500 - 3000 Ω)
C: 1 – 5 mA DC (Load resistance 3000 - 6000 Ω)
D: 0 – 20 mA DC (Load resistance 750 - 1500 Ω)
E: 0 – 16 mA DC (Load resistance 935 - 1875 Ω)
F: 0 – 10 mA DC (Load resistance 1500 - 3000 Ω)
G: 0 – 1 mA DC (Load resistance 15k - 30kΩ)
DW: -20 – +20 mA DC (Load resistance 500 - 1000Ω)
FW: -10 – +10 mA DC (Load resistance 1000 - 2000Ω)
Z: Specify current (See OUTPUT SPECIFICATIONS)
Voltage
80
(3.15)
127
(5)
mm (inch)
MODEL: SVB–[1][2]–[3][4]
8: 0 – 20 V DC (Load resistance 2000 Ω min.)
9: 0 – 30 V DC (Load resistance 3000 Ω min.)
8W: -20 – +20 V DC (Load resistance 2000 Ω min.)
0: Specify voltage (See OUTPUT SPECIFICATIONS)
Caution: The load resistance must be within the indicated
range for adequate operation.
ORDERING INFORMATION
• Code number: SVB-[1][2]-[3][4]
Specify a code from below for each of [1] through [4].
(e.g. SVB-6A-M2/E/K/Q)
• Special input and output ranges (For codes Z & 0)
• Specify the specification for option code /Q
(e.g. /C01/S01)
[3] POWER INPUT
AC Power
M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,
[1] INPUT
Current
47 – 66 Hz)
DC Power
A: 4 – 20 mA DC (Input resistance 250 Ω)
A1: 4 – 20 mA DC (Input resistance 50 Ω)
B: 2 – 10 mA DC (Input resistance 500 Ω)
C: 1 – 5 mA DC (Input resistance 1000 Ω)
D: 0 – 20 mA DC (Input resistance 50 Ω)
E: 0 – 16 mA DC (Input resistance 62.5 Ω)
F: 0 – 10 mA DC (Input resistance 100 Ω)
G: 0 – 1 mA DC (Input resistance 1000 Ω)
H: 10 – 50 mA DC (Input resistance 100 Ω)
J: 0 – 10 μA DC (Input resistance 1000 Ω)
K: 0 – 100 μA DC (Input resistance 1000 Ω)
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
[4] OPTIONS (multiple selections)
Input Signal Indicator
blank: Without
/E: With (0.0 - 100.0 % display)
Response Time (0 – 90 %)
blank: Standard (≤ 0.5 sec.)
/K: Fast Response (≤ 25 msec.)
SVB SPECIFICATIONS
ES-1307 Rev.4 Page 1/3
http://www.m-system.co.jp/
MODEL: SVB
Standards & Approvals
blank: Without CE
Minimum span: 10 V
Offset: Max. 1.5 times span
/CE: CE marking (Not selectable with /E)
Other Options
Load resistance: Output drive 10 mA max.
blank: none
INSTALLATION
Power Consumption
/Q: Option other than the above (specify the specification)
•AC:
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
Approx. 5 VA at 100 V
Approx. 6 VA at 200 V
Approx. 7 VA at 264 V
/C02: Polyurethane coating
•DC: Approx. 3 W
/C03: Rubber coating
Operating temperature: -5 to +60°C (23 to 140°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Surface or DIN rail
Weight: 400 g (0.88 lb)
TERMINAL SCREW MATERIAL
/S01: Stainless steel
GENERAL SPECIFICATIONS
Construction: Plug-in
PERFORMANCE in percentage of span
Accuracy: ±0.1 %
Connection: M3.5 screw terminals
Screw terminal: Chromated steel (standard) or stainless
steel
Display accuracy: ±(0.1 % of FS + 1 digit)
Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)
Line voltage effect: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @1 minute (input to output
to power to ground)
Housing material: Flame-resistant resin (black)
Isolation: Input to output to power
Overrange output: Approx. -10 to +110 % at 0 – 20 V
Zero adjustment: -2 to +2 % (front)
Span adjustment: 98 to 102 % (front)
■ DISPLAY (Input indicator)
STANDARDS & APPROVALS
EU conformity:
LCD digital display: 0.0 - 100.0 % (min. digit 0.1 %)
(No scaling)
EMC Directive
EMI EN 61000-6-4
INPUT SPECIFICATIONS
■ DC Current:
EMS EN 61000-6-2
Low Voltage Directive
EN 61010-1
Shunt resistor attached to the input terminals (0.5 W)
Specify input resistance value for code Z.
■ DC Voltage: -300 – +300 V DC
Minimum span: 10 mV
Installation Category II
Pollution Degree 2
Input or output to power: Reinforced insulation (300 V)
Input to output: Basic insulation (300 V)
RoHS Directive
Offset: Max. 1.5 times span
Input resistance
Span 10 – 100 mV : ≥ 10 kΩ
Span 0.1 – 1 V : ≥ 100 kΩ
EN 50581
Span ≥ 1 V : ≥ 1 MΩ
OUTPUT SPECIFICATIONS
■ DC Current: -20 – +20 mA DC
Minimum span: 1 mA
Offset: Max. 1.5 times span
Load resistance: Output drive 30 V max. and 15 V min.;
20 V max. and 10 V min. (0 % output = negative value)
■ DC Voltage: -20 – + 30 V DC
(The 0 – 100 % output range values within -10 – +12 V
range are not available.)
SVB SPECIFICATIONS
ES-1307 Rev.4 Page 2/3
http://www.m-system.co.jp/
MODEL: SVB
EXTERNAL DIMENSIONS unit: mm (inch)
CLAMP
(top & bottom)
7.8 (.31)
DIN RAIL
35mm wide
6
5
4
3
2–4.5 (.18) dia.
MTG HOLE
15 (.59) deep
7
8
1
2
8–M3.5
SCREW
50 (1.97)
107 (4.21)
127 (5)
40 (1.57)
50 (1.97)
[3.3 (.13)]
• When mounting, no extra space is needed between units.
TERMINAL ASSIGNMENTS unit: mm (inch)
INPUT RESISTOR
(model: REM)
6
5
4
3
7
8
1
2
Input shunt resistor attached
for current input.
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
**
Z
S
Isolation
Low Drift
Amplifier
Output
Driver
+
–
+
3
4
5
6
1
2
7
8
*
OUTPUT
POWER
INPUT
R
–
U(+)
V(–)
Base Socket
*Input shunt resistor attached for current input.
**Option /E
Specifications are subject to change without notice.
SVB SPECIFICATIONS
ES-1307 Rev.4 Page 3/3
http://www.m-system.co.jp/
SVB-J9-R/K 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
SVB-J9-R/Q | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 | |
SVB-JA-M2 | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 | |
SVB-JA-M2/CE | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 | |
SVB-JA-M2/E | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 | |
SVB-JA-M2/K | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 | |
SVB-JA-M2/Q | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 | |
SVB-JA-R | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 | |
SVB-JA-R/CE | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 | |
SVB-JA-R/E | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 | |
SVB-JA-R/K | MSYSTEM | Plug-in Signal Conditioners M-UNIT | 获取价格 |
SVB-J9-R/K 相关文章
- 2024-12-03
- 4
- 2024-12-03
- 7
- 2024-12-03
- 6
- 2024-12-03
- 7