首页 > W5PA-C7DA1-P/Q

W5PA-C7DA1-P/Q

更新时间：2025-07-09 22:37:17

品牌：MSYSTEM

描述：Terminal Block Dual Output Signal Conditioners W5-UNIT

PDF下载

中文翻译

免费 PCB/SMT

概述
数据手册

如果您发现信息不准确，欢迎纠错

W5PA-C7DA1-P/Q 概述

Terminal Block Dual Output Signal Conditioners W5-UNIT

W5PA-C7DA1-P/Q 数据手册

通过下载W5PA-C7DA1-P/Q数据手册来全面了解它。这个PDF文档包含了所有必要的细节，如产品概述、功能特性、引脚定义、引脚排列图等信息。

PDF下载

MODEL: W5PA

Voltage

Terminal Block Dual Output Signal Conditioners W5-UNIT

1: 0 – 10 mV DC (Load resistance 10 kΩ min.)

2: 0 – 100 mV DC (Load resistance 100 kΩ min.)

3: 0 – 1 V DC (Load resistance 100 Ω min.)

4: 0 – 10 V DC (Load resistance 1000 Ω min.)

5: 0 – 5 V DC (Load resistance 500 Ω min.)

6: 1 – 5 V DC (Load resistance 500 Ω min.)

4W: -10 – +10 V DC (Load resistance 2000 Ω min.)

5W: -5 – +5 V DC (Load resistance 1000 Ω min.)

0: Specify voltage (See OUTPUT SPECIFICATIONS)

FREQUENCY TRANSMITTER

Functions & Features

• Converts the output from a pulse-type transducer into two

isolated process signals

• Two independent output ranges

• Four-way isolation (input to output 1 to output 2 to power)

• High-density mounting

45 (1.77)

[4] OUTPUT 2

Same range availability as Output 1

Y: None

(3.82)

[5] POWER INPUT

AC Power

41 (1.61)

mm (inch)

M: 85 – 264 V AC (Operational voltage range 85 – 264 V,

47 – 66 Hz)

MODEL: W5PA-[1][2][3][4]-[5][6]

(CE not available)

DC Power

ORDERING INFORMATION

• Code number: W5PA-[1][2][3][4]-[5][6]

Specify a code from below for each [1] through [6].

(e.g. W5PA-A144W4W-R/Q)

R: 24 V DC

(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)

R2: 11 – 27 V DC

(Operational voltage range 11 – 27 V, ripple 10 %p-p max.)

(CE not available)

• Frequency range (e.g. 0 – 1 kHz)

• Special output ranges (For codes Z & 0)

• Specify the specification for option code /Q

(e.g. /C01/S01)

P: 110 V DC

(Operational voltage range 85 – 150 V, ripple 10 %p-p max.)

(CE not available)

[1] INPUT

A1: Open collector

[6] OPTIONS

blank: none

A2: Mechanical contact

C: 5 V pulse (sensitivity 2 V)

D: 12 V/24 V pulse (sensitivity 5 V)

/Q: With options (specify the specification)

SPECIFICATIONS OF OPTION: Q (multiple selections)

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

[2] EXCITATION

4: 12 V DC / 30 mA

7: 24 V DC / 12 mA

/C02: Polyurethane coating

/C03: Rubber coating

TERMINAL SCREW MATERIAL

/S01: Stainless steel

[3] OUTPUT 1

Current

A: 4 – 20 mA DC (Load resistance 550 Ω max.)

B: 2 – 10 mA DC (Load resistance 1100 Ω max.)

C: 1 – 5 mA DC (Load resistance 2200 Ω max.)

D: 0 – 20 mA DC (Load resistance 550 Ω max.)

E: 0 – 16 mA DC (Load resistance 685 Ω max.)

F: 0 – 10 mA DC (Load resistance 1100 Ω max.)

G: 0 – 1 mA DC (Load resistance 11 kΩ max.)

Z: Specify current (See OUTPUT SPECIFICATIONS)

CAUTION

The W5PA is designed to accept at the maximum of 100

kHz, which may cause errors due to chattering in the input

pulses.

A filter circuitry (time constant: approx. 1 msec.) is

incorporated to eliminate unwanted chattering when the

mechanical contact input is specified. It is effective for most

relay types, however, an external CR filter as indicated

W5PA SPECIFICATIONS

ES-8533 Rev.7 Page 1/3

http://www.m-system.co.jp/

MODEL: W5PA

below, could be added if the user needs improvement. Limit

Detecting L level

the input frequency to 10 Hz at maximum.

5 V pulse: ≤ 1 V

12 V, 24 V pulse: ≤ 4 V

C = 10 μF

R = 1 kΩ

FREQ

XMTR

Relay

OUTPUT SPECIFICATIONS

■ DC Current: 0 – 20 mA DC

Minimum span: 1 mA

Offset: Max. 1.5 times span

GENERAL SPECIFICATIONS

Construction: Terminal block

Load resistance: Output drive 11 V max.

■ DC Voltage: -10 – +12 V DC

Spans: Min. 5 mV, max. 20 V

Connection

Input: M3.5 screw terminals (torque 0.8 N·m)

Output & power: M3 screw terminals (torque 0.8 N·m)

Screw terminal: Nickel-plated steel (standard) or stainless

steel

Offset: Max. 1.5 times span

Load resistance: Output drive 10 mA max.; 5 mA for

negative voltage output; at ≥ 0.5 V

Housing material: Flame-resistant resin (black)

Isolation: Input to output 1 to output 2 to power

Overrange output: Approx. -10 to +120 % at 1 – 5 V

Zero adjustment: -2 to +2 % (front)

(±1 % with the output suffix codes 4W and 5W selected)

Span adjustment: 98 to 102 % (front)

(99 to 101 % with the output suffix codes 4W and 5W

selected.)

INSTALLATION

Power Consumption

•AC:

Approx. 6 VA at 100 V

Approx. 7 VA at 200 V

Approx. 8 VA at 264 V

•DC: Approx. 3 W

Operating temperature: -5 to +55°C (23 to 131°F)

Operating humidity: 0 to 90 %RH (non-condensing)

Mounting: DIN rail

INPUT SPECIFICATIONS

Sensor excitation:

Weight: 130 g (0.29 lb)

12 V DC; shortcircuit protection (approx. 35 mA at

shortcircuit)

PERFORMANCE in percentage of span

Accuracy: ±0.1 %

24 V DC; shortcircuit protection (approx. 15 mA at

shortcircuit)

Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)

Response time: Max. 0.5 sec. + 1 pulse cycle (0 – 90 %)

Line voltage effect: ±0.1 % over voltage range

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength:

■ Open Collector

Frequency range: 0 – 0.01 Hz through 100 kHz

Pulse width time requirement: ≥ 4 µsec. for both ON and

OFF

Sensing voltage/current: 5 V DC @2 mA

Detecting levels: ≤ 350 Ω / 1 V for ON; ≥ 10 kΩ / 3 V for OFF

■ Mechanical Contact

2000 V AC @1 minute (input to output 1 or output 2 to

power to ground)

1000 V AC @1 minute (output 1 to output 2)

Frequency range: 0 – 0.01 Hz through 30 Hz

Pulse width time requirement: ≥ 10 msec. for both ON and

OFF

STANDARDS & APPROVALS

EU conformity:

Sensing voltage/current: 5 V DC @2 mA

Detecting levels: ≤ 350 Ω / 1 V for ON; ≥ 10 kΩ / 3 V for OFF

■ Voltage Pulse

EMC Directive

EMI EN 61000-6-4

EMS EN 61000-6-2

RoHS Directive

Frequency range: 0 – 0.01 Hz through 100 kHz

Pulse width time requirement: ≥ 4 µsec. for both H and L

levels

EN 50581

Waveform: Square or sine

Input impedance: ≥ 10 kΩ

Max. voltage between input terminals: ±50 V

Detecting H level

5 V pulse: ≥ 3 V

12 V, 24 V pulse: ≥ 6 V

W5PA SPECIFICATIONS

ES-8533 Rev.7 Page 2/3

http://www.m-system.co.jp/

MODEL: W5PA

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)

7.4 (.29)

5–M3.5 SCREW

DIN RAIL

35mm wide

6 (.24)

9 10 11

45 (1.77)

41 (1.61)

[3.3 (.13)]

6–M3 SCREW

• When mounting, no extra space is needed between units.

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

Isolation

Waveform

Shaper

Digital

Computation

Voltage

Amplifier

Output

Driver

–

INPUT

OUTPUT 1

SENSOR EXCITATION

Excitation

Supply

Output

Driver

OUTPUT 2

POWER

–

U(+)

V(–)

Note 1: The section enclosed by broken line is only with 2nd output option.

Note 2: DO NOT connect to the terminals 1 and 2.

Input Connection Examples

■ Open Collector or Mechanical Contact ■ Voltage Pulse

+5V

2.5kΩ

–

Vsns

Specifications are subject to change without notice.

W5PA SPECIFICATIONS

ES-8533 Rev.7 Page 3/3

http://www.m-system.co.jp/

W5PA-C7DA1-P/Q 相关器件

型号	制造商	描述	价格	文档
W5PA-C7DA1-R	MSYSTEM	Terminal Block Dual Output Signal Conditioners W5-UNIT	获取价格
W5PA-C7DA1-R/Q	MSYSTEM	Terminal Block Dual Output Signal Conditioners W5-UNIT	获取价格
W5PA-C7DA1-R2	MSYSTEM	Terminal Block Dual Output Signal Conditioners W5-UNIT	获取价格
W5PA-C7DA1-R2/Q	MSYSTEM	Terminal Block Dual Output Signal Conditioners W5-UNIT	获取价格
W5PA-C7DA2-M	MSYSTEM	Terminal Block Dual Output Signal Conditioners W5-UNIT	获取价格
W5PA-C7DA2-M/Q	MSYSTEM	Terminal Block Dual Output Signal Conditioners W5-UNIT	获取价格
W5PA-C7DA2-P	MSYSTEM	Terminal Block Dual Output Signal Conditioners W5-UNIT	获取价格
W5PA-C7DA2-P/Q	MSYSTEM	Terminal Block Dual Output Signal Conditioners W5-UNIT	获取价格
W5PA-C7DA2-R	MSYSTEM	Terminal Block Dual Output Signal Conditioners W5-UNIT	获取价格
W5PA-C7DA2-R/Q	MSYSTEM	Terminal Block Dual Output Signal Conditioners W5-UNIT	获取价格