概述
数据手册UC1710_V01 概述
High Current FET Driver
UC1710_V01 数据手册
通过下载UC1710_V01数据手册来全面了解它。这个PDF文档包含了所有必要的细节，如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载UC1710
UC2710
UC3710
High Current FET Driver
FEATURES
DESCRIPTION
• Totem Pole Output with 6A
Source/Sink Drive
The UC1710 family of FET drivers is made with a high-speed Schottky pro-
cess to interface between low-level control functions and very high-power
switching devices-particularly power MOSFET’s. These devices accept
low-current digital inputs to activate a high-current, totem pole output which
can source or sink a minimum of 6A.
• 3ns Delay
• 20ns Rise and Fall Time into 2.2nF
• 8ns Rise and Fall Time into 30nF
• 4.7V to 18V Operation
Supply voltages for both V and V can independently range from 4.7V to
IN
C
18V. These devices also feature under-voltage lockout with hysteresis.
The UC1710 is packaged in an 8-pin hermetically sealed dual in-line pack-
age for –55°C to +125°C operation. The UC2710 and UC3710 are speci-
fied for a temperature range of –40°C to +85°C and 0°C to +70°C
respectively and are available in either an 8-pin plastic dual in-line or a
5-pin, TO-220 package. Surface mount devices are also available.
• Inverting and Non-Inverting Outputs
• Under-Voltage Lockout with
Hysteresis
• Thermal Shutdown Protection
• MINIDIP and Power Packages
ORDERING INFORMATION
TEMPERATURE
RANGE
PACKAGE
TRUTH TABLE
UC1710J
UC2710DW
UC2710J
UC2710N
UC2710T
UC3710DW
UC3710N
UC3710T
–55°C to +125°C
–40°C to +85°C
8 pin CDIP
INV
H
N.I.
H
Out
L
Not Available
Not Available
8 pin PDIP
OUT= INV and N.I.
OUT= INV or N.I.
L
H
H
5 pin TO220
16 pin SOIC-wide
8 pin PDIP
H
L
L
0°C to +70°C
L
L
L
5 pin TO220
BLOCK DIAGRAM
INTERNALLY CONNECTED IN T PACKAGE
OUTPUT BIAS
5
VIN
4
VC
LOGIC BIAS
3
2
Out
N.I. IN
8
TSD
Pwr Gnd
INV IN
1
7
UVLO
Logic Gnd
INTERNALLY CONNECTED IN T PACKAGE
UDG-99079
05/99
UC1710
UC2710
UC3710
ABSOLUTE MAXIMUM RATINGS
N-Package
J-Package
T-Package
Supply Voltage, Vin . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V . . . . . . . . . . . . . . 20V . . . . . . . . . . . . . . 20V
Collector Supply Voltage, VC . . . . . . . . . . . . . . . . . . . . 20V . . . . . . . . . . . . . . 20V . . . . . . . . . . . . . . 20V
Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18V . . . . . . . . . . . . . . 18V . . . . . . . . . . . . . . 18V
Output Current (Source or Sink)
±
Steady-State. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 500mA. . . . . . . . . . . . 500mA . . . . . . . . . . . . . ± 1A
Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3V-VIN . . . . . . . . –0.3V – VIN . . . . . . . . –0.3V – VIN
Power Dissipation at Ta=25°C . . . . . . . . . . . . . . . . . . . 1W. . . . . . . . . . . . . . . 1W. . . . . . . . . . . . . . . 3W
Power Dissipation at T (Case) = 25°C. . . . . . . . . . . . . . 2W. . . . . . . . . . . . . . . 2W. . . . . . . . . . . . . . 25W
Operating Junction Temperature. . . . . . . –55°C to +150°C . . . . –55°C to +150°C . . . . –55°C to +150°C
Storage Temperature . . . . . . . . . . . . . . . –65°C to +150°C . . . . –65°C to +150°C . . . . –65°C to +150°C
Lead Temperature (Soldering, 10 seconds) . . . . . . . 300°C . . . . . . . . . . . . 300°C . . . . . . . . . . . . 300°C
Note 1: All currents are positive into, negative out of the specified terminal.
Note 2: Consult Unitrode Integrated Circuits databook for information regarding thermal specifications
and limitations of packages.
CONNECTION DIAGRAMS
DIL-8 MINIDIP (Top View)
J or N Package
SOIC-16 (Top View)
DW Package
5-Pin TO-220 (Top View)
T Package
ELECTRICAL CHARACTERISTICS: Unless otherwise stated, these specifications apply for VIN = VC = 15V, No load,
TA = TJ.
PARAMETERS
VIN Supply Current
TEST CONDITIONS
VIN =18V, VC =18V, Output Low
VIN =18V, VC =18V, Output High
VIN =18V, VC =18V, Output Low
VIN =18V, VC =18V,Output High
VIN High to Low
MIN
TYP
26
MAX UNITS
35
30
5.0
8
mA
mA
mA
mA
V
21
VC Supply Current
UVLO Threshold
1.5
5.0
4.1
4.4
3.8
4.1
4.4
4.8
VIN Low to High
V
2
UC1710
UC2710
UC3710
ELECTRICAL CHARACTERISTICS: Unless otherwise stated, these specifications apply for VIN = VC = 15V, No load,
TA = TJ.
PARAMETERS
TEST CONDITIONS
MIN
TYP
MAX UNITS
UVLO Threshold Hysteresis
Digital Input Low Level
Digital Input High Level
Digital Input Current
0.1
0.3
0.5
0.8
V
V
2.0
V
Digital Input = 0.0V
–70
–4.0
1.35
3.2
µA
V
Output High Sat., VC – VO
IO= –100mA
IO= –6A
2.2
4.5
0.6
4.5
V
Output Low Sat., VO
IO= 100mA
IO= 6A
0.25
3.4
V
V
Thermal Shutdown
165
°C
From Inv., Input to Output (Note 3, 4):
Rise Time Delay
CL = 0
35
35
35
20
25
85
35
35
35
15
20
85
70
70
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
CL = 2.2nF
CL = 30nF
CL = 0
70
10% to 90% Rise
Fall Time Delay
90% to 10% Fall
40
CL = 2.2nF
CL = 30nF
CL = 0
40
150
70
CL = 2.2nF
CL = 30nF
CL = 0
70
80
40
CL = 2.2nF
CL = 30nF
40
150
From N.I. Input to Output (Note 3,4):
Rise Time Delay
CL = 0
35
35
35
20
25
85
35
35
35
15
20
85
30
70
70
70
40
40
150
70
70
80
40
50
150
40
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
mA
CL = 2.2nF
CL = 30nF
CL = 0
10% to 90% Rise
Fall Time Delay
90% to 10% Fall
CL = 2.2nF
CL = 30nF
CL = 0
CL = 2.2nF
CL = 30nF
CL = 0
CL = 2.2nF
CL = 30nF
TA = 25°C (Note 5) CL = 0
Total Supply Current at 200kHz Input
Switching Frequency
Note: 3. Delay measured from 50% input change to 10% output change.
Note: 4. Those parameters with CL = 30nF are not tested in production.
Note: 5. Inv. Input pulsed at 50% duty cycle with N.I. Input = 3V. or N.I. Input pulsed at 50% duty cycle with Inv. Input = 0V.
UNITRODE CORPORATION
7 CONTINENTAL BLVD. • MERRIMACK, NH 03054
TEL. (603) 424-2410 FAX (603) 424-3460
3
PACKAGE OPTION ADDENDUM
www.ti.com
8-Apr-2018
PACKAGING INFORMATION
Orderable Device
5962-0152001QPA
5962-0152001VPA
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-55 to 125
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
ACTIVE
CDIP
CDIP
JG
8
8
1
TBD
A42
N / A for Pkg Type
0152001QPA
UC1710
ACTIVE
JG
1
TBD
A42
N / A for Pkg Type
-55 to 125
0152001VPA
UC1710
UC1710J
ACTIVE
ACTIVE
CDIP
CDIP
JG
JG
8
8
1
1
TBD
TBD
A42
A42
N / A for Pkg Type
N / A for Pkg Type
-55 to 125
-55 to 125
UC1710J
UC1710J883B
0152001QPA
UC1710
UC2710N
UC2710NG4
UC2710T
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
PDIP
PDIP
P
P
8
8
50
50
50
50
40
40
50
50
50
50
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU SN
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
-40 to 85
-40 to 85
-40 to 85
-40 to 85
0 to 70
UC2710N
UC2710N
UC2710T
UC2710T
UC3710DW
UC3710DW
UC3710N
UC3710N
UC3710T
UC3710T
Green (RoHS
& no Sb/Br)
TO-220
TO-220
SOIC
KC
KC
DW
DW
P
5
Green (RoHS
& no Sb/Br)
UC2710TG3
UC3710DW
UC3710DWG4
UC3710N
5
Green (RoHS
& no Sb/Br)
CU SN
16
16
8
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU | Call TI
Call TI
SOIC
Green (RoHS
& no Sb/Br)
0 to 70
PDIP
Green (RoHS
& no Sb/Br)
0 to 70
UC3710NG4
UC3710T
PDIP
P
8
Green (RoHS
& no Sb/Br)
0 to 70
TO-220
TO-220
KC
KC
5
Green (RoHS
& no Sb/Br)
CU SN
0 to 70
UC3710TG3
5
Green (RoHS
& no Sb/Br)
CU SN
0 to 70
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
8-Apr-2018
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF UC1710, UC1710-SP, UC3710 :
Catalog: UC3710, UC1710
•
Military: UC1710
•
Space: UC1710-SP
•
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
•
Military - QML certified for Military and Defense Applications
•
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
8-Apr-2018
Space - Radiation tolerant, ceramic packaging and qualified for use in Space-based application
•
Addendum-Page 3
PACKAGE OPTION ADDENDUM
www.ti.com
4-Feb-2021
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
5962-0152001QPA
5962-0152001VPA
UC1710J
ACTIVE
CDIP
CDIP
CDIP
CDIP
JG
8
8
8
8
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
-55 to 125
-55 to 125
-55 to 125
-55 to 125
0152001QPA
UC1710
ACTIVE
ACTIVE
ACTIVE
JG
1
Non-RoHS
& Green
SNPB
SNPB
SNPB
0152001VPA
UC1710
JG
1
Non-RoHS
& Green
UC1710J
UC1710J883B
JG
1
Non-RoHS
& Green
0152001QPA
UC1710
UC2710N
UC3710DW
UC3710DWG4
UC3710N
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
PDIP
SOIC
P
DW
DW
P
8
16
16
8
50
40
40
50
50
50
50
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
RoHS & Green
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
Call TI | SN
SN
N / A for Pkg Type
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
-40 to 85
0 to 70
0 to 70
0 to 70
0 to 70
0 to 70
0 to 70
UC2710N
UC3710DW
UC3710DW
UC3710N
UC3710N
UC3710T
UC3710T
SOIC
PDIP
UC3710NG4
UC3710T
PDIP
P
8
TO-220
TO-220
KC
KC
5
UC3710TG3
5
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
4-Feb-2021
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF UC1710, UC1710-SP, UC3710 :
Catalog: UC3710, UC1710
•
Military: UC1710
•
Space: UC1710-SP
•
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
•
Military - QML certified for Military and Defense Applications
•
Space - Radiation tolerant, ceramic packaging and qualified for use in Space-based application
•
Addendum-Page 2
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party
intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages,
costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (https:www.ti.com/legal/termsofsale.html) or other applicable terms available either
on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s
applicable warranties or warranty disclaimers for TI products.IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2021, Texas Instruments Incorporated
UC1710_V01 相关器件
| 型号 | 制造商 | 描述 | 价格 | 文档 |
| UC1711 | TI | Dual Ultra High-Speed FET Driver | 获取价格 |
|
| UC1711J | TI | Dual Ultra High-Speed FET Driver | 获取价格 |
|
| UC1711JE883B | TI | Dual Ultra High-Speed FET Driver 16-CDIP -55 to 125 | 获取价格 |
|
| UC1711N | TI | UC1711N | 获取价格 |
|
| UC17131 | TI | Smart Power Switch | 获取价格 |
|
| UC17131J | TI | Smart Power Switch | 获取价格 |
|
| UC17131L | ETC | Single Peripheral Driver | 获取价格 |
|
| UC17132 | TI | Smart Power Switch | 获取价格 |
|
| UC17132J | TI | Smart Power Switch | 获取价格 |
|
| UC17132J | ROCHESTER | 0.9A BUF OR INV BASED PRPHL DRVR, CDIP8, DIP-14 | 获取价格 |
|
UC1710_V01 相关文章
中国台湾取消对台积电海外生产2nm芯片限制
- 2025-01-14
- 2
英伟达AI芯片机架过热问题引发关注，微软等客户削减订单
- 2025-01-14
- 2
Arm拟大幅提高芯片设计授权费用300%，并考虑自主开发芯片
- 2025-01-14
- 3
Rapidus计划6月向博通交付2nm芯片，日本半导体产业迈出新步伐
- 2025-01-14
- 2
