HSHM-H176DG5-8CP1-TR40B [3M]
176 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, PRESS FIT;
| 型号： | HSHM-H176DG5-8CP1-TR40B |
| 厂家： | 
3M ELECTRONICS |
| 描述： | 176 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, PRESS FIT 连接器 |
| 文件： | 总5页 (文件大小：1913K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
3M™MetPak™ HSHM Press-Fit Header
2 mm Type DG, 176 Signal Contacts, 8 Rows, Straight
HSHM Series
• Up to 5 Gb/s data rates
• Low crosstalk at high frequencies
• 50/100 Ω (single-ended /differential)
impedance
• Modular/scalable format IEC 61076-4-101
• 101 mated lines per linear inch
• Integrated guide pin
• End-to-end stackable with 8 row 3M™
MetPak™ CP2, HM and HSHM sockets
• Mates with HSHM D sockets
• See Regulatory Information Appendix (RIA)
for chemical compliance information
TS-2079-02
Sheet 1 of 3
Date Modified: March 13, 2007
Physical
Insulation
Material:
High Temperature Thermoplastic (LCP)
Flammability:
Contact
UL 94V-0
Copper Alloy
Material:
Plating:
See Ordering Information
Performance
Mechanical
Normal Force (Nominal):
Engagement Force (Nominal):
Separation Force (Nominal):
Wipe (Nominal, Shortest Contact):
Durability:
0.57 N [ 58 g ] Signal, 0.74 N [ 75 g ] Shield
0.32 N [ 33 g ] Signal, 0.22 N [ 22 g ] Shield
0.20 N [ 20 g ] Signal, 0.20 N [ 20 g ] Shield
2.67 mm [ 0.105 in. ] Signal, 1.57 mm [ 0.062 in ] Shield
250 cycles with TR40B plating
Application:
This module is suitable for stand-alone use. (Refer to IEC-61076-4-101.)
Electrical
Data Rate:
5 Gb/s
Characteristic Impedance:
Current Rating (Fully Loaded):
50 W Single-ended, 100 W Differential
1 A at 70× C Signal
4
Insulation Resistance:
Withstanding Voltage:
10 MW at 100 V
DC
750 V
RMS
Environmental
Temperature Rating:
-55×C to +125×C
UL File No.: E68080
MetPak is a trademark of 3M Company.
3M
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™MetPak™ HSHM Press-Fit Header
2 mm Type DG, 176 Signal Contacts, 8 Rows, Straight
HSHM Series
49.85
2.00
.079
1.963
2.00
.079
Pin positions
2.00
.079
2.00
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
.079
ROW I
ROW H
ROW G
ROW F
ROW E
ROW D
ROW C
18.00
.709
ROW B
ROW A
ROW Z
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Shield positions
48.00
21.40
.843
1.890
15.60
.614
denotes shield column (tail only) omitted for the
row differential pair part
Interstitial
ground
contacts
5.00
.197
1.50
.059
Signal
contacts
23.84
.938
HSHM-HXXXXX-8XPX-XXXXX
REV X XXYY
13.40
.528
DIM A
4.50
.177
DIM B
Coaxial, column differential and stripline configuration
shown with protective caps*
DIM C
DIM A = Pin mating length
DIM B = Shield tail length
DIM C = Pin tail length
HSHM-HXXXXX-8XPX-XXXXX
REV X
XXYY
mm
[inch]
Tolerance Unless Noted
Row differential configuration
shown with protective caps*
0
0.0
0.00
mm
±3
±0.3 ±0.13
* Caps to be removed after press-fit installation process
[ ] Dimensions for Reference Only
Ordering Information
(rows I and Z not loaded)
HSHM - H176DGX - 8CPX - XXXXX
High Speed Option:
4 =Coaxial, column differential and
stripline (75 Ω) applications
5 =Row differential applications
Plating μm [ μ″ ]:
TG30 = 0.76 [ 30 ] Min. Au Contact Area
2.54 [ 100 ] Min. SnPb Terminal Area
1 . 2 7 [ 5 0 ] M i n . N i A l l o v e r 0
(RIA E2 & C2 apply)
Standard Configuration
TR40B = 0.127 [ 5 ] Min. Hard Au Contact Area, Lubricated
1.02 [ 40 ] Min. PdNi Contact Area
DIM A = 5.3 mm for rows A through H
Tail Length:
0 . 1 0 [ 4 ] M i n . P d S t r i k e C o n t a c t A r e a
2.54 [ 100 ] Min. SnPb Terminal Area
1.27 [ 50 ] Min. Ni all over
1 =4.4 mm pin and 3.5 mm shield
2 =2 mm pin and 2 mm shield
For non-standard configurations
contact sales representative
(RIA E2 & C2 apply)
TS-2079-02
Sheet 2 of 3
3M
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™MetPak™ HSHM Press-Fit Header
2 mm Type DG, 176 Signal Contacts, 8 Rows, Straight
HSHM Series
2.00
1.00
1.00
2.00
25
24
23
22
21
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
20
+0.05
0
O 2.00
19
l O 0.10 A
B
18
17
16
15
14
13
12
11
10
9
4.00
4.00
O DIM. D
l O 0.10 M A
Plated thru holes
8
8
B
48.00
7
7
6
6
See hole plating table
5
5
4
4
3
3
2
2
1
1
A
H
G F E D C B A
H
G F E D C B A
6.00
B
Recommended PCB hole mounting pattern for row
differential applications
Recommended PCB hole mounting pattern for coaxial,
column differential and stripline applications
(Same geometry as left view without the ground vias)
HOLE PLATING TABLE mm
Cu. THICKNESS
0.025 - 0.045 [.0010 - .0018]
SnPb THICKNESS
0.008 -0.018 [.0003 - .0007]
DRILLED HOLE DIA.
0.584 - 0.625 [.0230 - .0246]
FINISHED HOLE DIA. “D”
0.457 - 0.559 [.0180 - .0220]
TS-2079-02
Sheet 3 of 3
3M is a trademark of 3M Company.
For technical, sales or ordering information call
3M
Interconnect Solutions
http://www.3M.com/interconnects/
800-225-5373
Regulatory Information Appendix
3M Electronic Solutions Division/Interconnect
EUROPE
Appendix E1: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product is RoHS Compliant 2005/95/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in
excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/
EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E2: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC
This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/747/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in
excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/
EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E3: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as
amended by Commission Decision 2005/618/EC.
This product contains lead in the solder tail area in excess of the maximum concentration value allowed.
Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon
information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E4: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/17/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in
excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision
2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in
writing, this information represents 3M’s best knowledge and belief based upon information provided by third party
suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
RIA-2217-B
CHINA
Appendix C1: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits
for Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006,
means that the product or part does not contain any of the following substances in excess of the following maximum
concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium,
polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise
stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by
third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
20
Appendix C2: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits
for Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006,
means that the product or part does contain a substance, as detailed in the chart below, in excess of the following
maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent
chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless
otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information
provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform
with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in
accordance with the product Warranty stated below.
Name and Content of Hazardous Substances or Elements
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the
accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended
application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s
current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in
writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER
WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to
replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any
indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.
3
Electronic Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
800/225-5373
www.3M.com/interconnects
RIA-2217-B
© 3M 2007
相关型号：
HSHM-S055B1-5AP1-TG30L
55 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, PRESS FIT, SOCKET, ROHS COMPLIANT
3M
HSHM-S055CR1-5AP1-TG50
55 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, PRESS FIT, SOCKET, ROHS COMPLIANT
3M
©2020 ICPDF网 联系我们和版权申明