HSHM-H200DE4-8CP1-TG50 [3M]
TWO PART BOARD CONNECTOR;型号: | HSHM-H200DE4-8CP1-TG50 |
厂家: | 3M ELECTRONICS |
描述: | TWO PART BOARD CONNECTOR 连接器 |
文件: | 总4页 (文件大小:1021K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
3M™ MetPak™ HSHM Press-Fit Header
2 mm Type DE, 200 Signal Contacts, 8 Rows, Straight
HSHM Series
• Up to 5 Gb/s data rates
• Low crosstalk at high frequencies
• 50/100 Ω (single-ended /differential) impedance
• Modular/scalable format IEC 61076-4-101
• 101 mated lines per linear inch
• Integrated guide pin
• End-to-end stackable with 8 row 3M™ MetPak™ CP2,
HM and HSHM headers
• See the Regulatory InformationAppendix (RIA) in
the “RoHS compliance” section of
www.3mconnector.com for compliance information
Date Modified: October 22, 2010
TS-2077-B
Sheet 1 of 3
Physical
Insulation:
Material: High Temperature Thermoplastic (LCP)
Flammability: UL 94V-0
Contact:
Material:
CopperAlloy
Plating: See Ordering Information
Performance
Mechanical:
Normal Force (Nominal): 0.57 N [58 g] Signal, 0.74 N [75 g] Shield
Engagement Force (Nominal): 0.32 N [33 g] Signal, 0.22 N [22 g] Shield
Separation Force (Nominal): 0.20 N [20 g] Signal, 0.20 N [20 g] Shield
Wipe (Nominal, Shortest Contact): 2.67 mm [0.105 in] Signal, 1.57 mm [0.062 in] Shield
Mate/Unmate Cycles: 250
Application: This module is not suitable for stand-alone use. (Refer to IEC-61076-4-101)
Electrical:
Data Rate: 5 Gb/s
Characteristic Impedance:
50 Ω Single-ended, 100 Ω Differential
Current Rating (Fully Loaded): 1A @ 70° C Signal
Insulation Resistance:
104 MΩ @ 100VDC
WithstandingVoltage: 750Vrms
Environmental
-55° C to 125° C
Temperature Rating:
UL File No.: E68080
MetPak is a trademark of 3M Company.
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M™ MetPak™ HSHM Press-Fit Header
2 mm Type DE, 200 Signal Contacts, 8 Rows, Straight
HSHM Series
2.00
2.00
.079
.079
Pin positions
2.00
.079
2.00
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
.079
ROW I
ROW H
ROW G
ROW F
ROW E
ROW D
ROW C
ROW B
18.00
.709
ROW A
ROW Z
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Shield positions
48.00
21.40
.843
1.890
17.85
.703
denotes shield column (tail only) omitted for the row
differential pair part
5.00
.197
Interstitial
ground
1.50
.059
contacts
Signal
contacts
4.50
.177
HSHM-HXXXXX-8XPX-XXXXX
REV X XXYY
15.15
.596
13.40
.528
DIM A
DIM B
4.50
.177
Coaxial, column differential and stripline configuration
shown with protective caps*
DIM C
DIM A = Pin mating length
DIM B = Shield tail length
DIM C = Pin tail length
HSHM-HXXXXX-8XPX-XXXXX
REV X
XXYY
mm
(Inch)
Tolerance Unless Noted
Row differential configuration
shown with protective caps*
0
0.0
0.3
0.00
0.13
mm
3
( ) Dimensions used for
Reference Only
* Caps to be removed after press-fit installation process
Ordering Information
(rows I and Z not loaded)
HSHM-H200DEX-8CPX- XXXXX
Plating μm [ μ” ]:
TG30 = 0.76 [30] Min.Au Contact Area
High Speed Option:
2.54 [100] Min. SnPb Terminal Area (RIA C2 & E2 apply)
1.27 [50] Min. Ni All over
Standard Option
4 = Coaxial, column differential and
stripline (75 Ω) applications
5 = Row differential applications
TG30L = 0.76 [30] Min.Au Contact Area, Lubricated
2.54 [100] Min. SnPb Terminal Area (RIA C2 & E2 apply)
1.27 [50] Min. Ni All over
Typically higher make order quantities as compared to TG30.
Tail Length:
TG50 =1.27 [50] Min.Au Contact Area, Lubricated
2.54 [100] Min. SnPb Terminal Area (RIA C2 & E2 apply)
1.27 [50] Min. Ni All over
1 = 4.4 mm pin and 3.5 mm shield
2 = 2 mm pin and 2 mm shield
Non-Standard Option (Available with longer lead times and
higher make order quantities, MOQ)
Standard Configuration
DIM A = 5.3 mm for rows A through H
For non--standard configurations contact sales representative
TS-2077-B
Sheet 2 of 3
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M™ MetPak™ HSHM Press-Fit Header
2 mm Type DE, 200 Signal Contacts, 8 Rows, Straight
HSHM Series
2.00
1.00
1.00
2.00
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
DIM. D
Ø
0.10
8
8
7
6
5
4
3
2
1
M
A B
Ø
48.00
7
Plated thru holes
See hole plating table
6
5
4
3
2
1
A
H
G F E D C B A
H
G F
E D C B A
14.00
B
Recommended PCB hole mounting pattern for row
differential applications
Recommended PCB hole mounting pattern for coaxial,
column differential and stripline applications
(Same geometry as left view without the ground vias)
Hole Plating Table mm
Finished Hole Dia. “D”
0.457 - 0.559 [.0180 - .0220]
Cu.Thickness
SnPb Thickness
Drilled Hole Dia.
0.025 - 0.045 [.0010 - .0018]
0.008 -0.018 [.0003 - .0007]
0.584 - 0.625 [.0230 - .0246]
TS-2077-B
Sheet 3 of 3
3M is a trademark of 3M Company.
3
For technical, sales or ordering information call
Electronic Solutions Division
Interconnect Solutions
800-225-5373
http://www.3Mconnector.com
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness
is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order
shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the
warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except
where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of
the legal theory asserted.
3M Electronics Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
U.S.A.
1-800-225-5373
www.3Mconnector.com
Please recycle. Printed in USA.
© 3M 2010. All rights reserved.
RIA-2217B-E
3M is a trademark of 3M Company.
相关型号:
HSHM-S055B1-5AP1-TG30L
55 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, PRESS FIT, SOCKET, ROHS COMPLIANT
3M
HSHM-S055CR1-5AP1-TG50
55 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, PRESS FIT, SOCKET, ROHS COMPLIANT
3M
HSHM-S055CR4-5AP1-TR40B
55 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, PRESS FIT, SOCKET
3M
HSHM-S088FL4-8AP1-TR40B
88 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, PRESS FIT, SOCKET
3M
©2020 ICPDF网 联系我们和版权申明