AD5316RBRUZ [ADI]
Quad, 10-Bit nanoDAC Reference, I2C Interface;
| 型号： | AD5316RBRUZ |
| 厂家： | 
ADI |
| 描述： | Quad, 10-Bit nanoDAC Reference, I2C Interface 光电二极管 转换器 |
| 文件： | 总24页 (文件大小：1091K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Quad, 10-Bit nanoDAC with 2 ppm/°C
Reference, I2C Interface
Data Sheet
AD5316R
FEATURES
FUNCTIONAL BLOCK DIAGRAM
V
GND
V
REF
DD
Low drift 2.5 V on-chip reference: 2 ppm/°C typical
Tiny package: 3 mm × 3 mm, 16-lead LFCSP
Total unadjusted error (TUE): 0.1% of FSR maximum
Offset error: 1.5 mV maximum
Gain error: 0.1% of FSR maximum
High drive capability: 20 mA, 0.5 V from supply rails
User-selectable gain of 1 or 2 (GAIN pin)
Reset to zero scale or midscale (RSTSEL pin)
1.8 V logic compatibility
400 kHz I2C-compatible serial interface
4 I2C addresses available
2.5V
AD5316R
REFERENCE
V
LOGIC
SCL
STRING
DAC A
INPUT
REGISTER
DAC
V
V
V
V
A
B
C
D
OUT
OUT
OUT
OUT
REGISTER
BUFFER
BUFFER
BUFFER
BUFFER
STRING
DAC B
INPUT
REGISTER
DAC
REGISTER
SDA
A1
STRING
DAC C
INPUT
REGISTER
DAC
REGISTER
A0
STRING
DAC D
INPUT
REGISTER
DAC
REGISTER
Low glitch: 0.5 nV-sec
Low power: 3.3 mW at 3 V
2.7 V to 5.5 V power supply
POWER-ON
RESET
GAIN =
×1/×2
POWER-
DOWN
LOGIC
LDAC RESET
RSTSEL
GAIN
−40°C to +105°C temperature range
Figure 1.
APPLICATIONS
Digital gain and offset adjustment
Programmable attenuators
Industrial automation
Data acquisition systems
GENERAL DESCRIPTION
The AD5316R, a member of the nanoDAC® family, is a low power,
quad, 10-bit buffered voltage output DAC. The device includes
a 2.5 V, 2 ppm/°C internal reference (enabled by default) and a
gain select pin giving a full-scale output of 2.5 V (gain = 1) or 5 V
(gain = 2). The device operates from a single 2.7 V to 5.5 V supply,
is guaranteed monotonic by design, and exhibits less than 0.1%
FSR gain error and 1.5 mV offset error performance. The device
is available in a 3 mm × 3 mm LFCSP package and in a TSSOP
package.
Table 1. Related Devices
Interface
Reference
Internal
External
Internal
External
12-Bit
10-Bit
SPI
AD5684R
AD5684
AD5694R
AD5694
AD5317R
AD5317
I2C
AD53161
1 The AD5316R and the AD5316 are not pin-to-pin or software compatible.
PRODUCT HIGHLIGHTS
The AD5316R also incorporates a power-on reset circuit and a
RSTSEL pin; the RSTSEL pin ensures that the DAC outputs power
up to zero scale or midscale and remain at that level until a valid
write takes place. The part contains a per-channel power-down
feature that reduces the current consumption of the device in
power-down mode to 4 µA at 3 V.
1. Precision DC Performance.
Total unadjusted error: 0.1% of FSR maximum
Offset error: 1.5 mV maximum
Gain error: 0.1% of FSR maximum
2. Low Drift 2.5 V On-Chip Reference.
2 ppm/°C typical temperature coefficient
5 ppm/°C maximum temperature coefficient
3. Two Package Options.
The AD5316R uses a versatile 2-wire serial interface that operates
at clock rates up to 400 kHz and includes a VLOGIC pin intended
for 1.8 V/3 V/5 V logic.
3 mm × 3 mm, 16-lead LFCSP
16-lead TSSOP
Rev. C
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rightsof third parties that may result fromits use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks andregisteredtrademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2012–2017 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
AD5316R
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
I2C Slave Address........................................................................ 18
Serial Operation ......................................................................... 18
Write Operation.......................................................................... 18
Read Operation........................................................................... 19
Multiple DAC Readback Sequence.......................................... 19
Power-Down Operation ............................................................ 20
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description......................................................................... 1
Product Highlights ........................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
AC Characteristics........................................................................ 4
Timing Characteristics ................................................................ 5
Absolute Maximum Ratings............................................................ 6
Thermal Resistance ...................................................................... 6
ESD Caution.................................................................................. 6
Pin Configurations and Function Descriptions ........................... 7
Typical Performance Characteristics ............................................. 8
Terminology .................................................................................... 14
Theory of Operation ...................................................................... 16
Digital-to-Analog Converter .................................................... 16
Transfer Function ....................................................................... 16
DAC Architecture....................................................................... 16
Serial Interface ............................................................................ 17
Write and Update Commands.................................................. 17
LDAC
Load DAC (Hardware
Pin)........................................... 20
Mask Register ................................................................. 21
Hardware Reset Pin ( ) ................................................... 21
LDAC
RESET
Reset Select Pin (RSTSEL) ........................................................ 21
Internal Reference Setup ........................................................... 22
Solder Heat Reflow..................................................................... 22
Long-Term Temperature Drift ................................................. 22
Thermal Hysteresis .................................................................... 22
Applications Information .............................................................. 23
Microprocessor Interfacing....................................................... 23
AD5316R to ADSP-BF531 Interface ........................................ 23
Layout Guidelines....................................................................... 23
Galvanically Isolated Interface ................................................. 23
Outline Dimensions....................................................................... 24
Ordering Guide .......................................................................... 24
REVISION HISTORY
5/2017—Rev. B to Rev. C
2/2014—Rev. A to Rev. B
Changes to Features Section............................................................ 1
Changes to Table 2 Summary.......................................................... 3
Changes to Table 3............................................................................ 4
Changes to Table 4 Summary.......................................................... 5
Changes to Table 5............................................................................ 6
Change to Table 2 ..............................................................................3
Change to Table 7 ..............................................................................9
Deleted Figure 7, Renumbered Sequentially .................................8
Deleted Long-Term Temperature Drift Section and
Figure 48 .......................................................................................... 22
RESET
Changes to VLOGIC Pin Description and
Pin Description,
7/2012—Rev. 0 to Rev. A
Table 7 ................................................................................................ 7
Changes to Figure 13 to Figure 16.................................................. 9
Changes to Figure 17 to Figure 21................................................ 10
Changes to Figure 27...................................................................... 11
Changes to Figure 34...................................................................... 12
Changes to Figure 35...................................................................... 13
Change to Features Section..............................................................1
Change to Relative Accuracy Parameter in Table 2 ......................3
Change to Differential Nonlinearity Parameter in Table 2..........3
Changes to Ordering Guide.......................................................... 24
7/2012—Revision 0: Initial Version
RESET
Changes to Hardware Reset (
) Section............................ 21
Added Long-Term Temperature Drift Section and Figure 47;
Renumbered Sequentially.............................................................. 22
Changes to Ordering Guide .......................................................... 24
Rev. C | Page 2 of 24
Data Sheet
AD5316R
SPECIFICATIONS
VDD = 2.7 V to 5.5 V; VREF = 2.5 V; 1.62 V ≤ VLOGIC ≤ 5.5 V; RL = 2 kΩ; CL = 200 pF; all specifications TMIN to TMAX, unless otherwise noted.
Table 2.
Parameter
Min
Typ
Max
Unit
Test Conditions/Comments1, 2
STATIC PERFORMANCE3
Resolution
10
Bits
Relative Accuracy
Differential Nonlinearity
Zero-Code Error
Offset Error
Full-Scale Error
Gain Error
0.12
0.5
0.5
1.5
1.5
0.1
0.1
0.1
0.2
LSB
LSB
mV
mV
% of FSR
% of FSR
% of FSR
% of FSR
µV/°C
ppm
Guaranteed monotonic by design
All 0s loaded to DAC register
0.4
+0.1
+0.01
0.02
0.01
All 1s loaded to DAC register
Total Unadjusted Error
External reference, gain = 2, TSSOP
Internal reference, gain = 1, TSSOP
Offset Error Drift4
1
1
0.15
2
Gain Temperature Coefficient4
DC Power Supply Rejection Ratio4
DC Crosstalk4
Of FSR/°C
DAC code = midscale; VDD = 5 V 10%
Due to single channel, full-scale output
change
mV/V
µV
3
2
µV/mA
µV
Due to load current change
Due to power-down (per channel)
OUTPUT CHARACTERISTICS4
Output Voltage Range
0
0
VREF
2 × VREF
V
V
nF
nF
kΩ
Gain = 1
Gain = 2 (see Figure 25)
RL = ∞
Capacitive Load Stability
2
10
RL = 1 kΩ
Resistive Load5
Load Regulation
1
DAC code = midscale
80
80
40
25
2.5
µV/mA
µV/mA
mA
Ω
µs
5 V 10%; −30 mA ≤ IOUT ≤ +30 mA
3 V 10%; −20 mA ≤ IOUT ≤ +20 mA
Short-Circuit Current6
Load Impedance at Rails7
Power-Up Time
See Figure 25
Coming out of power-down mode; VDD = 5 V
REFERENCE OUTPUT
Output Voltage8
2.4975
2.5025
5
V
At TA
Reference TC9
2
0.04
12
240
20
40
ppm/°C
Ω
See the Terminology section
Output Impedance4
Output Voltage Noise4
Output Voltage Noise Density4
Load Regulation, Sourcing4
Load Regulation, Sinking4
Output Current Load Capability4
Line Regulation4
µV p-p
nV/√Hz
µV/mA
µV/mA
mA
µV/V
ppm
ppm
0.1 Hz to 10 Hz
At TA, f = 10 kHz, CL = 10 nF
At TA
At TA
VDD ≥ 3 V
At TA
First cycle
Additional cycles
5
100
125
25
Thermal Hysteresis4
LOGIC INPUTS4
Input Current
2
µA
V
V
Per pin
Input Low Voltage, VINL
Input High Voltage, VINH
Pin Capacitance
0.3 × VLOGIC
0.7 × VLOGIC
2
pF
Rev. C | Page 3 of 24
AD5316R
Data Sheet
Parameter
Min
Typ
Max
Unit
Test Conditions/Comments1, 2
LOGIC OUTPUTS (SDA)4
Output Low Voltage, VOL
0.4
V
ISINK = 3 mA
Floating State Output Capacitance
4
pF
POWER REQUIREMENTS
VLOGIC
ILOGIC
VDD
1.8
5.5
3
5.5
5.5
V
µA
V
2.7
VREF + 1.5
Gain = 1
Gain = 2
V
IDD
VIH = VDD, VIL = GND, VDD = 2.7 V to 5.5 V
Internal reference off
Internal reference on, at full scale
−40°C to +85°C
Normal Mode10
0.59
1.1
1
0.7
1.3
4
mA
mA
µA
All Power-Down Modes11
6
µA
−40°C to +105°C
1 Temperature range is −40°C to +105°C.
2 The AD5316R and the AD5316 are not pin-to-pin or software compatible.
3 DC specifications are tested with the outputs unloaded, unless otherwise noted. Upper dead band (10 mV) exists only when VREF = VDD with gain = 1 or when VREF/2 = VDD
with gain = 2. Linearity calculated using a reduced code range of 4 to 1020.
4 Guaranteed by design and characterization; not production tested.
5 Channel A and Channel B can have a combined output current of up to 30 mA. Similarly, Channel C and Channel D can have a combined output current of up to
30 mA up to a junction temperature of 110°C.
6 VDD = 5 V. The device includes current limiting that is intended to protect the device during temporary overload conditions. Junction temperature can be exceeded
during current limit. Operation above the specified maximum junction temperature may impair device reliability.
7 When drawing a load current at either rail, the output voltage headroom with respect to that rail is limited by the 25 Ω typical channel resistance of the output
devices. For example, when sinking 1 mA, the minimum output voltage = 25 Ω × 1 mA = 25 mV (see Figure 25).
8 Initial accuracy presolder reflow is 750 µV; output voltage includes the effects of preconditioning drift. See the Solder Heat Reflow section.
9 Reference is trimmed and tested at two temperatures and is characterized from −40°C to +105°C. Reference temperature coefficient is calculated as per the box method.
See the Terminology section for more information.
10 Interface inactive. All DACs active. DAC outputs unloaded.
11 All DACs powered down.
AC CHARACTERISTICS
VDD = 2.7 V to 5.5 V; VREF = 2.5 V; 1.62 V ≤ VLOGIC ≤ 5.5 V; RL = 2 kΩ; CL = 200 pF; all specifications TMIN to TMAX, unless otherwise noted.
Table 3.
Parameter1, 2
Min
Typ
5
Max
Unit
Test Conditions/Comments3
Output Voltage Settling Time
Slew Rate
Digital-to-Analog Glitch Impulse
Digital Feedthrough
Digital Crosstalk
7
µs
V/µs
¼ to ¾ scale settling to 1 LSB
0.8
0.5
0.13
0.1
0.2
0.3
−80
300
nV-sec
nV-sec
nV-sec
nV-sec
nV-sec
dB
1 LSB change around major carry transition
Analog Crosstalk
DAC-to-DAC Crosstalk
Total Harmonic Distortion4
Output Noise Spectral Density
At TA, BW = 20 kHz, VDD = 5 V, fOUT = 1 kHz
DAC code = midscale, 10 kHz, gain = 2,
internal reference enabled
nV/√Hz
Output Noise
6
µV p-p
0.1 Hz to 10 Hz
1 Guaranteed by design and characterization; not production tested.
2 See the Terminology section.
3 Temperature range is −40°C to +105°C; typical at 25°C.
4 Digitally generated sine wave at 1 kHz.
Rev. C | Page 4 of 24
Data Sheet
AD5316R
TIMING CHARACTERISTICS
VDD = 2.7 V to 5.5 V; 1.62 V ≤ VLOGIC ≤ 5.5 V; all specifications TMIN to TMAX, unless otherwise noted.
Table 4.
Parameter1, 2 Min
Max
Unit
µs
µs
µs
µs
ns
µs
µs
µs
µs
ns
ns
ns
ns
ns
pF
Description
t1
t2
t3
t4
t5
t6
t7
t8
t9
t10
t11
t12
t13
tSP
2.5
0.6
1.3
0.6
100
0
0.6
0.6
1.3
0
20 + 0.1CB
20
400
0
SCL cycle time
tHIGH, SCL high time
tLOW, SCL low time
tHD,STA, start/repeated start hold time
tSU,DAT, data setup time
tHD,DAT, data hold time
tSU,STA, repeated start setup time
tSU,STO, stop condition setup time
tBUF, bus free time between a stop condition and a start condition
tR, rise time of SCL and SDA when receiving
tF, fall time of SCL and SDA when transmitting/receiving
LDAC pulse width
3
0.9
4
300
300
4, 5
SCL rising edge to LDAC rising edge
6
50
400
Pulse width of suppressed spike
Capacitive load for each bus line
5
CB
1 See Figure 2.
2 Guaranteed by design and characterization; not production tested.
3 A master device must provide a hold time of at least 300 ns for the SDA signal (referred to the VIH min of the SCL signal) to bridge the undefined region of the SCL
falling edge.
4 tR and tF are measured from 0.3 × VDD to 0.7 × VDD
5 CB is the total capacitance of one bus line in pF.
.
6 Input filtering on the SCL and SDA inputs suppresses noise spikes that are less than 50 ns.
Timing Diagram
START
CONDITION
REPEATED START
CONDITION
STOP
CONDITION
SDA
t9
t10
t11
t4
t3
SCL
t4
t2
t1
t6
t5
t7
t8
t12
1
2
t13
LDAC
LDAC
t12
NOTES
1
ASYNCHRONOUS LDAC UPDATE MODE.
SYNCHRONOUS LDAC UPDATE MODE.
2
Figure 2. 2-Wire Serial Interface Timing Diagram
Rev. C | Page 5 of 24
AD5316R
Data Sheet
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
THERMAL RESISTANCE
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages. This
value was measured using a JEDEC standard 4-layer board with
zero airflow. For the LFCSP package, the exposed pad must be
tied to GND.
Table 5.
Parameter
Rating
VDD to GND
VLOGIC to GND
VOUT to GND
VREF to GND
Digital Input Voltage to GND1
SDA and SCL to GND
Operating Temperature Range
Storage Temperature Range
Junction Temperature
−0.3 V to +7 V
−0.3 V to +7 V
−0.3 V to VDD + 0.3 V
−0.3 V to VDD + 0.3 V
−0.3 V to VLOGIC + 0.3 V
−0.3 V to +7 V
−40°C to +105°C
−65°C to +150°C
125°C
Table 6. Thermal Resistance
Package Type
16-Lead LFCSP
16-Lead TSSOP
θJA
Unit
°C/W
°C/W
70
112.6
Reflow Soldering Peak Temperature,
Pb Free (J-STD-020)
260°C
ESD CAUTION
1 Excluding SDA and SCL.
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
Rev. C | Page 6 of 24
Data Sheet
AD5316R
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
AD5316R
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
V
RSTSEL
RESET
A1
REF
V
V
B
A
OUT
V
V
A 1
12 A1
11 SCL
10 A0
OUT
OUT
GND 2
AD5316R
GND
SCL
TOP VIEW
V
3
4
DD
(Not to Scale)
V
A0
DD
9
V
LOGIC
C
OUT
V
V
C
D
V
LOGIC
OUT
OUT
GAIN
LDAC
SDA
TOP VIEW
(Not to Scale)
NOTES
1. THE EXPOSED PAD MUST BE TIED TO GND.
Figure 3. 16-Lead LFCSP Pin Configuration
Figure 4. 16-Lead TSSOP Pin Configuration
Table 7. Pin Function Descriptions
Pin No.
TSSOP
LFCSP
Mnemonic
VOUT
Description
1
2
3
3
4
5
A
GND
VDD
Analog Output Voltage from DAC A. The output amplifier has rail-to-rail operation.
Ground Reference Point for All Circuitry on the Part.
Power Supply Input. The part can be operated from 2.7 V to 5.5 V. The supply should be decoupled
with a 10 µF capacitor in parallel with a 0.1 µF capacitor to GND.
4
5
6
6
7
8
VOUT
VOUT
SDA
C
D
Analog Output Voltage from DAC C. The output amplifier has rail-to-rail operation.
Analog Output Voltage from DAC D. The output amplifier has rail-to-rail operation.
Serial Data Input. This pin is used in conjunction with the SCL line to clock data into or out of the
24-bit input shift register. SDA is a bidirectional, open-drain data line that should be pulled to the
supply with an external pull-up resistor.
7
8
9
LDAC
GAIN
LDAC can be operated in two modes, asynchronous update mode and synchronous update mode.
Pulsing this pin low allows any or all DAC registers to be updated if the input registers have new
data; all DAC outputs are simultaneously updated. This pin can also be tied permanently low.
10
Gain Select Pin. When this pin is tied to GND, all four DAC outputs have a span of 0 V to VREF.
When this pin is tied to VLOGIC, all four DAC outputs have a span of 0 V to 2 × VREF
.
9
10
11
11
12
13
VLOGIC
A0
SCL
Digital Power Supply. Voltage ranges from 1.62 V to 5.5 V.
Address Input. Sets the first LSB of the 7-bit slave address.
Serial Clock Line. This pin is used in conjunction with the SDA line to clock data into or out of the
24-bit input shift register.
12
13
14
15
A1
RESET
Address Input. Sets the second LSB of the 7-bit slave address.
Asynchronous Reset Input. The RESET input is falling edge sensitive. When RESET is activated (low), the
input register and the DAC register are updated with zero scale or midscale, depending on the
state of the RSTSEL pin. When RESET is low, all LDAC pulses are ignored. If the pin is not used, tie it
permanently to VLOGIC. If the pin is forced low at power-up, the POR circuit does not initialize correctly
until the pin is released.
14
15
16
1
RSTSEL
VREF
Power-On Reset Pin. When this pin is tied to GND, all four DACs are powered up to zero scale.
When this pin is tied to VLOGIC, all four DACs are powered up to midscale.
Reference Voltage. The AD5316R has an internal reference. When the internal reference is used,
VREF is the reference output pin. When an external reference is used, VREF is the reference input
pin. By default, the internal reference is used, and this pin is a reference output.
16
17
2
N/A
VOUT
EPAD
B
Analog Output Voltage from DAC B. The output amplifier has rail-to-rail operation.
Exposed Pad. The exposed pad must be tied to GND.
Rev. C | Page 7 of 24
AD5316R
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
2.5020
DEVICE 1
DEVICE 2
DEVICE 3
DEVICE 4
DEVICE 5
V
= 5V
DD
V
= 5V
DD
= 25°C
T
A
2.5015
2.5010
2.5005
2.5000
2.4995
2.4990
2.4985
2.4980
1
–40
–20
0
20
40
60
80
100
120
CH1 2µV
M1.0s
TEMPERATURE (°C)
Figure 8. Internal Reference Noise, 0.1 Hz to 10 Hz
Figure 5. Internal Reference Voltage vs. Temperature
2.5000
2.4999
2.4998
2.4997
2.4996
2.4995
2.4994
2.4993
90
80
70
60
50
40
30
20
10
0
V
= 5V
V
= 5V
DD
DD
= 25°C
T
A
–0.005
–0.003
–0.001
I
0.001
(A)
0.003
0.005
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
TEMPERATURE DRIFT (ppm/°C)
LOAD
Figure 6. Reference Output Temperature Drift Histogram
Figure 9. Internal Reference Voltage vs. Load Current
1600
1400
1200
1000
800
600
400
200
0
2.5002
2.5000
2.4998
2.4996
2.4994
2.4992
2.4990
V
= 5V
= 25°C
DD
T
= 25°C
A
T
A
DEVICE 1
DEVICE 3
DEVICE 2
4.0
10
100
1k
10k
100k
1M
2.5
3.0
3.5
4.5
5.0
5.5
FREQUENCY (Hz)
SUPPLY VOLTAGE (V)
Figure 7. Internal Reference Noise Spectral Density vs. Frequency
Figure 10. Internal Reference Voltage vs. Supply Voltage
Rev. C | Page 8 of 24
Data Sheet
AD5316R
0.5
0.15
0.12
0.09
0.06
0.03
0
0.3
0.1
INL
DNL
–0.1
–0.3
–0.03
–0.06
–0.09
–0.12
–0.15
V
= 5V
= 25°C
V
= 5V
DD
= 25°C
DD
T
T
A
A
INTERNAL REFERENCE = 2.5V
–0.5
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
0
156
312
468
CODE
624
780
936
V
(V)
REF
Figure 11. INL
Figure 14. INL Error and DNL Error vs. VREF
0.5
0.3
0.15
0.12
0.09
0.06
0.03
0
0.1
INL
DNL
–0.1
–0.3
–0.5
–0.03
–0.06
–0.09
–0.12
–0.15
V
= 5V
= 25°C
DD
T
= 25°C
A
T
A
INTERNAL REFERENCE = 2.5V
INTERNAL REFERENCE = 2.5V
0
156
312
468
CODE
624
780
936
2.7
3.2
3.7
4.2
4.7
5.2
SUPPLY VOLTAGE (V)
Figure 12. DNL
Figure 15. INL Error and DNL Error vs. Supply Voltage
0.15
0.12
0.09
0.06
0.03
0
0.10
0.08
0.06
0.04
0.02
0
FULL-SCALE ERROR
GAIN ERROR
INL
DNL
–0.03
–0.06
–0.09
–0.12
–0.15
–0.02
–0.04
–0.06
–0.08
–0.10
V
= 5V
V
= 5V
DD
DD
INTERNAL REFERENCE = 2.5V
INTERNAL REFERENCE = 2.5V
–40 10
60
110
–20
0
20
40
60
80
100
120
–40
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 16. Gain Error and Full-Scale Error vs. Temperature
Figure 13. INL Error and DNL Error vs. Temperature
Rev. C | Page 9 of 24
AD5316R
Data Sheet
0.10
0.09
0.08
0.07
0.06
0.05
0.04
0.03
0.02
0.01
0
V
= 5V
DD
V
= 5V
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
DD
INTERNAL REFERENCE = 2.5V
INTERNAL REFERENCE = 2.5V
ZERO-CODE ERROR
OFFSET ERROR
–40
–20
0
20
40
60
80
100
120
–40
–20
0
20
40
60
80
100
120
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 20. TUE vs. Temperature
Figure 17. Zero-Code Error and Offset Error vs. Temperature
0.10
0.08
0.06
0.04
0.02
0
0.10
0.08
0.06
0.04
0.02
0
GAIN ERROR
FULL-SCALE ERROR
–0.02
–0.04
–0.06
–0.08
–0.10
–0.02
–0.04
–0.06
–0.08
–0.10
T
= 25°C
A
T
= 25°C
A
INTERNAL REFERENCE = 2.5V
INTERNAL REFERENCE = 2.5V
2.7
3.2
3.7
4.2
4.7
5.2
2.7
3.2
3.7
4.2
4.7
5.2
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
Figure 18. Gain Error and Full-Scale Error vs. Supply Voltage
Figure 21. TUE vs. Supply Voltage, Gain = 1
1.5
1.0
0
–0.01
–0.02
–0.03
–0.04
–0.05
–0.06
–0.07
–0.08
–0.09
–0.10
0.5
ZERO-CODE ERROR
0
OFFSET ERROR
–0.5
–1.0
V
= 5V
DD
T
= 25°C
A
T = 25°C
A
INTERNAL REFERENCE = 2.5V
INTERNAL REFERENCE = 2.5V
156 312 468
CODE
–1.5
2.7
3.2
3.7
4.2
4.7
5.2
0
624
780
936 1023
SUPPLY VOLTAGE (V)
Figure 19. Zero-Code Error and Offset Error vs. Supply Voltage
Figure 22. TUE vs. Code
Rev. C | Page 10 of 24
Data Sheet
AD5316R
7
6
V
= 5V
= 25°C
DD
V
= 5V
DD
= 25°C
25
20
15
10
5
T
A
T
A
EXTERNAL
REFERENCE = 2.5V
INTERNAL
REFERENCE = 2.5V
GAIN = 2
0xFFFF
5
4
0xC000
0x8000
0x4000
0x0000
3
2
1
0
–1
0
–2
–0.06
540
560
580
600
620
640
–0.04
–0.02
0
0.02
0.04
0.06
I
(mA)
DD
LOAD CURRENT (A)
Figure 26. Source and Sink Capability at 5 V
Figure 23. IDD Histogram with External Reference, 5 V
5
4
V
= 5V
DD
= 25°C
V
= 3V
= 25°C
DD
30
25
20
15
10
5
T
A
T
A
INTERNAL
REFERENCE = 2.5V
GAIN = 1
EXTERNAL
REFERENCE = 2.5V
0xFFFF
0xC000
3
2
0x8000
0x4000
1
0x0000
0
–1
–2
0
1000
1020
1040
I
1060
1080
1100
1120
1140
–0.06
–0.04
–0.02
0
0.02
0.04
0.06
FULL SCALE (mA)
DD
LOAD CURRENT (A)
Figure 24. IDD Histogram with Internal Reference, VREF = 2.5 V, Gain = 2
Figure 27. Source and Sink Capability at 3 V
1.0
0.8
0.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
FULL-SCALE
ZERO CODE
0.4
SINKING, 2.7V
0.2
SINKING, 5V
0
EXTERNAL REFERENCE, FULL-SCALE
–0.2
SOURCING, 5V
–0.4
–0.6
–0.8
–1.0
SOURCING, 2.7V
15
–40
10
60
110
0
5
10
20
25
30
TEMPERATURE (°C)
LOAD CURRENT (mA)
Figure 25. Headroom/Footroom vs. Load Current
Figure 28. Supply Current vs. Temperature
Rev. C | Page 11 of 24
AD5316R
Data Sheet
4.0
3.5
3.0
2.5
2.0
1.5
1.0
2.5008
2.5003
2.4998
2.4993
2.4988
V
V
V
V
A
B
C
D
OUT
OUT
OUT
OUT
CHANNEL B
= 25°C
T
A
V
T
= 5V
DD
= 25°C
V
= 5.25V
DD
0.5
0
A
INTERNAL REFERENCE = 2.5V
CODE = 0x7FFF TO 0x8000
ENERGY = 0.227206nV-sec
INTERNAL REFERENCE = 2.5V
¼ TO ¾ SCALE
10
20
40
80
160
320
0
2
4
6
8
10
12
TIME (µs)
TIME (µs)
Figure 29. Settling Time
Figure 32. Digital-to-Analog Glitch Impulse
0.06
0.05
0.04
0.03
0.02
0.01
0
6
0.003
0.002
0.001
0
V
V
V
V
V
A
B
C
D
OUT
OUT
OUT
OUT
DD
V
V
V
B
C
D
OUT
OUT
OUT
5
4
3
2
1
–0.001
–0.002
0
T
= 25°C
A
INTERNAL REFERENCE = 2.5V
–0.01
–1
15
–10
–5
0
5
10
0
5
10
15
20
25
TIME (µs)
TIME (µs)
Figure 30. Power-On Reset to 0 V
Figure 33. Analog Crosstalk, VOUT
A
3
V
V
V
V
A
B
C
D
OUT
OUT
OUT
OUT
T
GAIN = 2
2
1
0
GAIN = 1
1
V
= 5V
DD
= 25°C
V
= 5V
= 25°C
DD
T
A
T
A
INTERNAL REFERENCE = 2.5V
EXTERNAL REFERENCE = 2.5V
–5
0
5
10
TIME (µs)
CH1 2µV M1.0s
A CH1
802mV
Figure 31. Exiting Power-Down to Midscale
Figure 34. 0.1 Hz to 10 Hz Output Noise Plot, 2.5 V External Reference
Rev. C | Page 12 of 24
Data Sheet
AD5316R
20
0
V
= 5V
DD
= 25°C
T
T
A
INTERNAL REFERENCE = 2.5V
–20
–40
–60
–80
1
–100
–120
–140
–160
–180
V
= 5V
= 25°C
DD
T
A
INTERNAL REFERENCE = 2.5V
0
2000 4000 6000 8000 10000 12000 14000 16000 18000 20000
FREQUENCY (Hz)
CH1 2µV M1.0s
A CH1
802mV
Figure 35. 0.1 Hz to 10 Hz Output Noise Plot, 2.5 V Internal Reference
Figure 37. Total Harmonic Distortion at 1 kHz
1600
4.0
3.9
3.8
3.7
3.6
3.5
3.4
3.3
3.2
3.1
3.0
V
T
= 5V
= 25°C
DD
0nF
FULL-SCALE
MIDSCALE
ZERO-SCALE
V
= 5V
= 25°C
DD
0.1nF
0.22nF
4.7nF
10nF
A
T
A
1400
1200
1000
800
600
400
200
0
INTERNAL REFERENCE = 2.5V
INTERNAL REFERENCE = 2.5V
10
100
1k
10k
100k
1M
1.590 1.595 1.600 1.605 1.610 1.615 1.620 1.625 1.630
FREQUENCY (Hz)
TIME (ms)
Figure 36. Noise Spectral Density
Figure 38. Settling Time vs. Capacitive Load
Rev. C | Page 13 of 24
AD5316R
Data Sheet
TERMINOLOGY
Relative Accuracy or Integral Nonlinearity (INL)
Relative accuracy or integral nonlinearity is a measurement of
the maximum deviation, in LSBs, from a straight line passing
through the endpoints of the DAC transfer function. Figure 11
shows a typical INL vs. code plot.
Output Voltage Settling Time
The output voltage settling time is the amount of time it takes
for the output of a DAC to settle to a specified level for a ¼ to ¾
full-scale input change.
Digital-to-Analog Glitch Impulse
Differential Nonlinearity (DNL)
Digital-to-analog glitch impulse is the impulse injected into the
analog output when the input code in the DAC register changes
state. It is normally specified as the area of the glitch in nV-sec,
and is measured when the digital input code is changed by 1 LSB
at the major carry transition (0x7FFF to 0x8000) (see Figure 32).
Differential nonlinearity is the difference between the measured
change and the ideal 1 LSB change between any two adjacent
codes. A specified differential nonlinearity of 1 LSB maximum
ensures monotonicity. The AD5316R is guaranteed monotonic
by design. Figure 12 shows a typical DNL vs. code plot.
Digital Feedthrough
Zero-Code Error
Digital feedthrough is a measurement of the impulse injected
into the analog output of the DAC from the digital inputs of the
DAC, but is measured when the DAC output is not updated. It
is specified in nV-sec and measured with a full-scale code change
on the data bus, that is, from all 0s to all 1s and vice versa.
Zero-code error is a measurement of the output error when
zero code (0x0000) is loaded to the DAC register. Ideally, the
output should be 0 V. The zero-code error is always positive in
the AD5316R because the output of the DAC cannot go below
0 V due to a combination of the offset errors in the DAC and
the output amplifier. Zero-code error is expressed in mV.
Figure 17 shows a plot of zero-code error vs. temperature.
Noise Spectral Density (NSD)
Noise spectral density is a measurement of the internally gener-
ated random noise. Random noise is characterized as a spectral
density (nV/√Hz) and is measured by loading the DAC to mid-
scale and measuring noise at the output. It is measured in nV/√Hz.
Figure 36 shows a plot of noise spectral density.
Full-Scale Error
Full-scale error is a measurement of the output error when full-
scale code (0xFFFF) is loaded to the DAC register. Ideally, the
output should be VDD − 1 LSB. Full-scale error is expressed as a
percentage of the full-scale range (% of FSR). Figure 16 shows a
plot of full-scale error vs. temperature.
DC Crosstalk
DC crosstalk is the dc change in the output level of one DAC
in response to a change in the output of another DAC. It is
measured with a full-scale output change on one DAC (or soft
power-down and power-up) while monitoring another DAC
kept at midscale. It is expressed in μV.
Gain Error
Gain error is a measurement of the span error of the DAC. It is
the deviation in slope of the DAC transfer characteristic from
the ideal expressed in % of FSR.
DC crosstalk due to load current change is a measurement
of the impact that a change in load current on one DAC has
on another DAC kept at midscale. It is expressed in μV/mA.
Gain Temperature Coefficient
Gain temperature coefficient is a measurement of the change in
gain error with changes in temperature. It is expressed in ppm
of FSR/°C.
Digital Crosstalk
Digital crosstalk is the glitch impulse transferred to the output
of one DAC at midscale in response to a full-scale code change
(all 0s to all 1s and vice versa) in the input register of another
DAC. It is expressed in nV-sec.
Offset Error
Offset error is a measurement of the difference between VOUT
(actual) and VOUT (ideal) expressed in mV in the linear region
of the transfer function. It can be negative or positive.
Analog Crosstalk
Offset Error Drift
Offset error drift is a measurement of the change in offset error
with changes in temperature. It is expressed in µV/°C.
Analog crosstalk is the glitch impulse transferred to the output
of one DAC in response to a change in the output of another DAC.
To measure analog crosstalk, load one of the input registers with
a full-scale code change (all 0s to all 1s and vice versa), and then
execute a software LDAC and monitor the output of the DAC
whose digital code was not changed. The area of the glitch is
expressed in nV-sec.
DC Power Supply Rejection Ratio (PSRR)
DC PSRR indicates how the output of the DAC is affected by
changes in the supply voltage. PSRR is the ratio of the change
in VOUT to a change in VDD for midscale output of the DAC. It
is measured in mV/V. VREF is held at 2.5 V, and VDD is varied
by 10%.
Rev. C | Page 14 of 24
Data Sheet
AD5316R
DAC-to-DAC Crosstalk
Voltage Reference Temperature Coefficient (TC)
DAC-to-DAC crosstalk is the glitch impulse transferred to the
output of one DAC in response to a digital code change and
subsequent analog output change of another DAC. It is measured
by loading one channel with a full-scale code change (all 0s to
all 1s and vice versa) using the write to and update commands
while monitoring the output of another channel that is at mid-
scale. The energy of the glitch is expressed in nV-sec.
Voltage reference TC is a measurement of the change in the
reference output voltage with a change in temperature. The
reference TC is calculated using the box method, which defines
the TC as the maximum change in the reference output over a
given temperature range expressed in ppm/°C, as follows:
VREFmax − VREFmin
TC =
× 106
V
×TempRange
REFnom
Total Harmonic Distortion (THD)
THD is the difference between an ideal sine wave and its
attenuated version using the DAC. The sine wave is used as the
reference for the DAC; THD is a measurement of the harmonics
present on the DAC output. It is measured in dB.
where:
REFmax is the maximum reference output measured over the
total temperature range.
REFmin is the minimum reference output measured over the total
temperature range.
REFnom is the nominal reference output voltage, 2.5 V.
V
V
V
TempRange is the specified temperature range of −40°C to
+105°C.
Rev. C | Page 15 of 24
AD5316R
Data Sheet
THEORY OF OPERATION
The resistor string structure is shown in Figure 40. Each resistor
in the string has a value R. The code loaded to the DAC register
determines the node on the string from which the voltage is
tapped off and fed into the output amplifier. The voltage is
tapped off by closing one of the switches that connect the string
to the amplifier. Because the AD5316R is a string of resistors, it
is guaranteed monotonic.
DIGITAL-TO-ANALOG CONVERTER
The AD5316R is a quad, 10-bit, serial input, voltage output DAC
with an internal reference. The part operates from supply
voltages of 2.7 V to 5.5 V. Data is written to the AD5316R in a
24-bit word format via a 2-wire serial interface. The AD5316R
incorporates a power-on reset circuit to ensure that the DAC
output powers up to a known output state. The device also has
a software power-down mode that reduces the typical current
consumption to 1 µA.
V
REF
R
TRANSFER FUNCTION
R
R
The internal reference is on by default. Because the input coding
to the DAC is straight binary, the ideal output voltage when using
an external reference is given by
TO OUTPUT
AMPLIFIER
D
2
VOUT = VREF × Gain
N
where:
REF is the value of the external reference.
Gain is the gain of the output amplifier and is set to 1 by default.
The gain can be set to 1 or 2 using the gain select pin. When the
GAIN pin is tied to GND, all four DAC outputs have a span of
0 V to VREF. When this pin is tied to VDD, all four DAC outputs
V
R
R
have a span of 0 V to 2 × VREF
D is the decimal equivalent of the binary code that is loaded to
the DAC register (0 to 1023).
.
Figure 40. Resistor String Structure
Internal Reference
N is the DAC resolution (10 bits).
The AD5316R on-chip reference is on at power-up but can be
disabled via a write to a control register. For more information,
see the Internal Reference Setup section.
DAC ARCHITECTURE
The DAC architecture consists of a string DAC followed by an
output amplifier. Figure 39 shows a block diagram of the DAC
architecture.
The 2.5 V, 2 ppm/°C internal reference provides a full-scale
output of 2.5 V or 5 V, depending on the state of the GAIN pin.
The internal reference is available at the VREF pin. This buffered
reference is capable of driving external loads of up to 10 mA.
V
REF
2.5V
REF
Output Amplifiers
REF (+)
The output buffer amplifier can generate rail-to-rail voltages on
its output for an output range of 0 V to VDD. The actual range
depends on the value of VREF, the GAIN pin, the offset error,
and the gain error. The GAIN pin selects the gain of the output.
INPUT
REGISTER
DAC
REGISTER
RESISTOR
STRING
V
X
OUT
REF (–)
GAIN
(GAIN = 1 OR 2)
GND
•
When this pin is tied to GND, all four outputs have a gain
of 1, and the output range is from 0 V to VREF
When this pin is tied to VDD, all four outputs have a gain
of 2, and the output range is from 0 V to 2 × VREF
Figure 39. Single DAC Channel Architecture Block Diagram
.
•
.
The output amplifiers are capable of driving a load of 1 kΩ in
parallel with 2 nF to GND. The slew rate is 0.8 V/µs with a ¼
to ¾ scale settling time of 5 µs.
Rev. C | Page 16 of 24
Data Sheet
AD5316R
Table 9. Address Bits and Selected DACs
SERIAL INTERFACE
Address Bits
The AD5316R has a 2-wire, I2C-compatible serial interface (see
the I2C-Bus Specification, Version 2.1, January 2000, available
from Philips Semiconductor). See Figure 2 for a timing diagram
of a typical write sequence. The AD5316R can be connected to
an I2C bus as a slave device, under the control of a master device.
The AD5316R supports standard (100 kHz) and fast (400 kHz)
data transfer modes. Support is not provided for 10-bit address-
ing or general call addressing.
DAC D DAC C DAC B DAC A Selected DAC Channels1
0
0
0
0
0
0
0
1
1
…
1
0
0
0
1
1
1
1
0
0
…
1
0
1
1
0
0
1
1
0
0
…
1
1
0
1
0
1
0
1
0
1
…
1
DAC A
DAC B
DAC A and DAC B
DAC C
DAC A and DAC C
DAC B and DAC C
DAC A, DAC B, and DAC C
DAC D
DAC A and DAC D
…
All DACs
Input Shift Register
The input shift register of the AD5316R is 24 bits wide. Data
is loaded into the device, MSB first, as a 24-bit word under the
control of the serial clock input, SCL. The input shift register
consists of an 8-bit command byte and a 16-bit data-word (see
Figure 41). The first eight MSBs make up the command byte.
1 Any combination of DAC channels can be selected using the address bits.
The 8-bit command byte is followed by two data bytes, which con-
tain the data-word. The data-word comprises the 10-bit input code,
followed by six don’t care bits (see Figure 41). The data bits are
transferred to the input register on the 24 falling edges of SCL.
The first four bits of the command byte are the command
bits (C3, C2, C1, and C0), which control the mode of
operation of the device (see Table 8).
The last four bits of the command byte are the address bits
(DAC D, DAC C, DAC B, and DAC A), which select the
DAC that is operated on by the command (see Table 9).
Commands can be executed on one DAC channel, any two or
three DAC channels, or on all four DAC channels, depending
on the address bits selected (see Table 9).
Table 8. Command Definitions
WRITE AND UPDATE COMMANDS
Command Bits
C3
0
0
C2
0
0
C1
0
0
C0
0
1
Command
LDAC
Pin) section.
For more information about the
LDAC
function, see the Load
No operation
Write to Input Register n (dependent
on LDAC)
DAC (Hardware
Write to Input Register n (Dependent on
)
LDAC
Command 0001 allows the user to write to each DAC’s
LDAC
0
0
1
0
Update DAC Register n with contents
of Input Register n
dedicated input register individually. When
is low, the
LDAC
0
0
0
0
0
1
0
1
1
1
0
0
1
0
1
Write to and update DAC Channel n
Power down/power up DAC
Hardware LDAC mask register
Software reset (power-on reset)
Internal reference setup register
Reserved
input register is transparent (if not controlled by the
mask register).
Update DAC Register n with Contents of Input Register n
1
1
X1
1
1
X1
0
1
X1
Command 0010 loads the DAC registers/outputs with the
contents of the input registers selected by the address bits
(see Table 9) and updates the DAC outputs directly.
1 X = don’t care.
Write to and Update DAC Channel n (Independent of
)
LDAC
Command 0011 allows the user to write to the DAC registers
and update the DAC outputs directly, independent of the state
LDAC
of the
pin.
DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
C3
C2
C1
C0 DAC D DAC C DAC B DAC A D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
X
X
X
X
X
X
COMMAND
DAC ADDRESS
DAC DATA
DAC DATA
COMMAND BYTE
DATA HIGH BYTE
DATA LOW BYTE
Figure 41. Input Shift Register Contents
Rev. C | Page 17 of 24
AD5316R
Data Sheet
I2C SLAVE ADDRESS
3. Data is transmitted over the serial bus in sequences of nine
clock pulses (eight data bits followed by an acknowledge bit).
Transitions on the SDA line must occur during the low period
of SCL; SDA must remain stable during the high period of SCL.
4. After all data bits are read or written, a stop condition is
established. In write mode, the master pulls the SDA line high
during the 10th clock pulse to establish a stop condition. In
read mode, the master issues a no acknowledge for the 9th
clock pulse (that is, the SDA line remains high). The master
then brings the SDA line low before the 10th clock pulse and
then high again during the 10th clock pulse to establish a
stop condition.
The AD5316R has a 7-bit I2C slave address. The five MSBs are
00011 and the two LSBs (A1 and A0) are set by the state of the
A1 and A0 address pins. The ability to make hardwired changes
to A1 and A0 allows the user to incorporate up to four AD5316R
devices on one bus (see Table 10).
Table 10. Device Address Selection
A1 Pin Connection
A0 Pin Connection
A1 Bit
A0 Bit
GND
GND
VLOGIC
VLOGIC
GND
VLOGIC
GND
VLOGIC
0
0
1
1
0
1
0
1
WRITE OPERATION
SERIAL OPERATION
The 2-wire I2C serial bus protocol operates as follows:
When writing to the AD5316R, the user must begin with a start
W
command followed by an address byte (R/ = 0), after which the
DAC acknowledges that it is prepared to receive data by pulling
SDA low. The AD5316R requires two bytes of data for the DAC
and a command byte that controls various DAC functions. Three
bytes of data must, therefore, be written to the DAC with the
command byte followed by the most significant data byte and the
least significant data byte, as shown in Figure 42. All these data
bytes are acknowledged by the AD5316R. A stop condition follows.
1. The master initiates a data transfer by establishing a start
condition when a high-to-low transition on the SDA line
occurs while SCL is high. The following byte is the address
byte, which consists of the 7-bit slave address.
2. The slave device with the transmitted address responds by
pulling SDA low during the 9th clock pulse (this is called
the acknowledge bit). At this stage, all other devices on the
bus remain idle while the selected device waits for data to
be written to, or read from, its input shift register.
1
9
1
9
SCL
SDA
0
0
0
1
1
A1
A0
R/W
DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16
ACK BY
ACK BY
AD5316R
START BY
MASTER
AD5316R
FRAME 1
SLAVE ADDRESS
FRAME 2
COMMAND BYTE
1
9
1
9
SCL
(CONTINUED)
SDA
(CONTINUED)
DB15 DB14 DB13 DB12 DB11 DB10 DB9
DB7
DB6 DB5 DB4
DB3
DB2
DB1
DB0
DB8
STOP BY
MASTER
ACK BY
AD5316R
ACK BY
AD5316R
FRAME 3
MOST SIGNIFICANT
DATA BYTE
FRAME 4
LEAST SIGNIFICANT
DATA BYTE
Figure 42. I2C Write Operation
Rev. C | Page 18 of 24
Data Sheet
AD5316R
READ OPERATION
MULTIPLE DAC READBACK SEQUENCE
When reading data back from the AD5316R, the user must begin
When reading data back from multiple AD5316R DACs, the
W
W
with a start command followed by an address byte (R/ = 0), after
user begins with an address byte (R/ = 0), after which the
which the DAC acknowledges that it is prepared to receive data
by pulling SDA low. The address byte must be followed by the
command byte, which determines both the read command that
is to follow and the pointer address to read from; the command
byte is also acknowledged by the DAC. The user configures the
channel to read back the contents of one or more DAC registers
and sets the readback command to active using the command byte.
DAC acknowledges that it is prepared to receive data by pulling
SDA low. The address byte must be followed by the command
byte, which is also acknowledged by the DAC. The user selects
the first channel to read back using the command byte.
Following this, the master establishes a repeated start condition,
W
and the address is resent with R/ = 1. This byte is acknowledged
by the DAC, indicating that it is prepared to transmit data. The
first two bytes of data are then read from DAC Input Register n
(selected using the command byte), most significant byte first, as
shown in Figure 43. The next two bytes read back are the contents
of DAC Input Register n + 1, and the next bytes read back are the
contents of DAC Input Register n + 2. Data is read from the DAC
input registers in this auto-incremented fashion until a NACK
followed by a stop condition follows. If the contents of DAC Input
Register D are read out, the next two bytes of data that are read
are the contents of DAC Input Register A.
Following this, the master establishes a repeated start condition,
W
and the address is resent with R/ = 1. This byte is acknowledged
by the DAC, indicating that it is prepared to transmit data. Two
bytes of data are then read from the DAC, as shown in Figure 43.
A NACK condition from the master, followed by a stop condition,
completes the read sequence. If more than one DAC is selected,
Channel A is read back by default.
1
9
1
9
SCL
SDA
0
0
0
1
1
A1
A0
R/W
DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16
ACK BY
ACK BY
AD5316R
START BY
MASTER
AD5316R
FRAME 1
SLAVE ADDRESS
FRAME 2
COMMAND BYTE
1
9
1
9
SCL
SDA
0
0
0
1
1
A1
A0
R/W
DB15 DB14 DB13 DB12 DB11 DB10 DB9
DB8
REPEATED START BY
MASTER
ACK BY
AD5316R
ACK BY
MASTER
FRAME 3
SLAVE ADDRESS
FRAME 4
MOST SIGNIFICANT
DATA BYTE n
1
9
1
9
SCL
(CONTINUED)
SDA
(CONTINUED)
DB15 DB14 DB13 DB12 DB11 DB10 DB9
DB8
DB7 DB6
DB5 DB4
DB3 DB2
DB1
DB0
ACK BY
MASTER
NACK BY
MASTER
STOP BY
MASTER
FRAME 5
LEAST SIGNIFICANT
DATA BYTE n
FRAME 6
MOST SIGNIFICANT
DATA BYTE n + 1
Figure 43. I2C Read Operation
Rev. C | Page 19 of 24
AD5316R
Data Sheet
POWER-DOWN OPERATION
AMPLIFIER
V
X
Command 0100 is designated for the power-down function.
The AD5316R provides three separate power-down modes
(see Table 11). These power-down modes are software program-
mable by setting Bit DB7 to Bit DB0 in the input shift register
(see Table 12). Two bits are associated with each DAC channel.
Table 11 shows how the state of these two bits corresponds to
the mode of operation of the device.
DAC
OUT
POWER-DOWN
CIRCUITRY
RESISTOR
NETWORK
Figure 44. Output Stage During Power-Down
Table 11. Modes of Operation
The bias generator, output amplifier, resistor string, and other
associated linear circuitry are shut down when power-down
mode is activated. However, the contents of the DAC registers
are unaffected in power-down mode, and the DAC registers can
be updated while the device is in power-down mode. The time
required to exit power-down is typically 2.5 µs for VDD = 5 V.
Operating Mode
Normal Operation
Power-Down Modes
1 kΩ to GND
100 kΩ to GND
Three-State
PDx1
PDx0
0
0
0
1
1
1
0
1
To reduce the current consumption further, the on-chip reference
can be powered off (see the Internal Reference Setup section).
Any or all DACs (DAC A to DAC D) can be powered down
to the selected mode by setting the corresponding bits in the
input shift register. See Table 12 for the contents of the input
shift register during the power-down/power-up operation.
LOAD DAC (HARDWARE LDAC PIN)
The AD5316R DAC has double buffered interfaces consisting of
two banks of registers: input registers and DAC registers. The user
can write to any combination of the input registers (see Table 9).
When both Bit PDx1 and Bit PDx0 (where x is the DAC selected)
in the input shift register are set to 0, the part works normally
with its normal power consumption of 1.1 mA at 5 V. When Bit
PDx1, Bit PDx0, or both Bit PDx1 and Bit PDx0 are set to 1, the
part is in power-down mode. In power-down mode, the supply
current falls to 4 μA at 5 V.
LDAC
Updates to the DAC registers are controlled by the
pin.
OUTPUT
AMPLIFIER
10-BIT
DAC
V
V
X
REF
OUT
In power-down mode, the output stage is internally switched
from the output of the amplifier to a resistor network of known
values. In this way, the output impedance of the part is known
when the part is in power-down mode.
DAC
LDAC
REGISTER
INPUT
REGISTER
Table 11 lists the three power-down options. The output is
connected internally to GND through either a 1 kΩ or a 100 kΩ
resistor, or it is left open-circuited (three-state). The output stage
is illustrated in Figure 44.
SCL
SDA
INPUT SHIFT
REGISTER
Figure 45. Simplified Diagram of Input Loading Circuitry for a Single DAC
Table 12. 24-Bit Input Shift Register Contents for Power-Down/Power-Up Operation1
DB23
(MSB) DB22
DB15
DB0
(LSB)
DB21
DB20
DB19 to DB16 to DB8 DB7
DB6
DB5
DB4
DB3
DB2
DB1
0
1
0
0
X
X
PDD1
PDD0
PDC1
PDC0
PDB1
PDB0
PDA1
PDA0
Command bits (C3 to C0)
Address bits
(don’t care)
Don’t
care
Power-down
select, DAC D
Power-down
select, DAC C
Power-down
select, DAC B
Power-down
select, DAC A
1 X = don’t care.
Rev. C | Page 20 of 24
Data Sheet
AD5316R
LDAC
LDAC
Instantaneous DAC Updating (
Held Low)
Table 13.
Overwrite Definition
Load
Register
LDAC
LDAC
For instantaneous updating of the DACs,
is held low while
Bit
LDAC
data is clocked into the input register using Command 0001. Both
the addressed input register and the DAC register are updated on
the 24th clock, and the output begins to change (see Table 14).
Pin
Operation
LDAC
LDAC
1 or 0
X1
(DB3 to DB0)
0
1
Determined by the LDAC pin.
DAC channels are updated. (DAC
channels see LDAC pin as 1.)
LDAC
Deferred DAC Updating (
For deferred updating of the DACs,
is clocked into the input register using Command 0001. All DAC
Pulsed Low)
LDAC
is held high while data
1 X = don’t care.
HARDWARE RESET PIN (
)
RESET
LDAC
outputs are asynchronously updated by pulling
low after the
LDAC
th
24 clock. The update occurs on the falling edge of
.
RESET
is an active low reset that allows the outputs to be cleared
to either zero scale or midscale. The clear code value is user select-
able via the reset select pin (RSTSEL). It is necessary to
LDAC MASK REGISTER
LDAC
Command 0101 is reserved for the software
When this command is executed, the address bits are ignored.
LDAC
function.
RESET
keep
low for a minimum of 30 ns to complete the
operation.
When writing to the DAC using Command 0101, the 4-bit
LDAC
RESET
When the
signal is returned high, the output remains at
mask register (DB3 to DB0) is loaded. Bit DB3 of the
mask
the cleared value until a new value is programmed. The outputs
RESET
register corresponds to DAC D; Bit DB2 corresponds to DAC C;
Bit DB1 corresponds to DAC B; and Bit DB0 corresponds to
DAC A.
cannot be updated with a new value while the
pin is low.
There is also a software executable reset function that resets the
DAC to the power-on reset code. Command 0110 is designated
for this software reset function (see Table 8). Any events
LDAC
The default value of these bits is 0; that is, the
normally. Setting any of these bits to 1 forces the selected DAC
LDAC
pin works
LDAC
RESET
on
during a power-on reset are ignored. If the
pin
channel to ignore transitions on the
pin, regardless of the
pin. This flexibility is useful in appli-
cations where the user wishes to select which channels respond
LDAC
is pulled low at power-up, the device does not initialize correctly
until the pin is released.
LDAC
state of the hardware
RESET SELECT PIN (RSTSEL)
to the
pin.
The AD5316R contains a power-on reset circuit that controls
the output voltage during power-up. When the RSTSEL pin is
tied to GND, the outputs power up to zero scale (note that this
is outside the linear region of the DAC). When the RSTSEL pin
is tied to VDD, the outputs power up to midscale. The outputs
remain powered up at the level set by the RSTSEL pin until a
valid write sequence is made to the DAC.
LDAC
control over the hardware
The
mask register allows the user extra flexibility and
LDAC
pin (see Table 13). Setting
LDAC
the
bit (DB3 to DB0) to 0 for a DAC channel allows the
LDAC
hard-ware
pin to control the updating of that channel.
1
LDAC
Table 14. Write Commands and
Pin Truth Table
Hardware
Pin State
LDAC
Input Register
Contents
Command
Description
DAC Register Contents
No change (no update)
Data update
0001
Write to Input Register n (dependent on LDAC)
VLOGIC
GND2
Data update
Data update
No change
0010
Update DAC Register n with contents of Input
Register n
VLOGIC
Updated with input register
contents
GND
No change
Updated with input register
contents
0011
Write to and update DAC Channel n
VLOGIC
GND
Data update
Data update
Data update
Data update
1 A high to low transition on the hardware
pin always updates the contents of the DAC register with the contents of the input register on channels that are not
LDAC
masked (blocked) by the
mask register.
LDAC
pin is permanently tied low, the
2 When the
mask bits are ignored.
LDAC
LDAC
Rev. C | Page 21 of 24
AD5316R
Data Sheet
INTERNAL REFERENCE SETUP
LONG-TERM TEMPERATURE DRIFT
By default, the internal reference is on at power-up. To reduce
the supply current, the on-chip reference can be turned off.
Command 0111 is reserved for setting up the internal reference.
To turn off the internal reference, set the software programmable
bit, DB0, in the input shift register using Command 0111, as
shown in Table 16. Table 15 shows how the state of the DB0 bit
corresponds to the mode of operation.
Figure 47 shows the change in the VREF (ppm) value after
1000 hours at 25°C ambient temperature.
140
120
100
80
Table 15. Internal Reference Setup Register
60
Internal Reference
Setup Register (Bit DB0)
40
Action
0
1
Reference on (default)
Reference off
20
0
SOLDER HEAT REFLOW
–20
0
100 200 300 400 500 600 700 800 900 1000
ELAPSED TIME (Hours)
As with all IC reference voltage circuits, the reference value
experiences a shift induced by the soldering process. Analog
Devices, Inc., performs a reliability test called precondition to
mimic the effect of soldering a device to a board. The output
voltage specification in Table 2 includes the effect of this
reliability test.
Figure 47. Reference Drift Through to 1000 Hours
THERMAL HYSTERESIS
Thermal hysteresis is the voltage difference induced on the
reference voltage by sweeping the temperature from ambient
to cold, then to hot, and then back to ambient.
Figure 46 shows the effect of solder heat reflow (SHR) as
measured through the reliability test (precondition).
Thermal hysteresis data is shown in Figure 48. It is measured by
sweeping the temperature from ambient to −40°C, then to +105°C,
and then back to ambient. The VREF delta is then measured between
the two ambient measurements (shown in blue in Figure 48). The
same temperature sweep and measurements were immediately
repeated, and the results are shown in red in Figure 48.
9
POSTSOLDER
HEAT REFLOW
60
50
40
30
20
10
0
PRESOLDER
HEAT REFLOW
FIRST TEMPERATURE SWEEP
SUBSEQUENT TEMPERATURE SWEEPS
8
7
6
5
4
3
2
1
0
2.498
2.499
2.500
(V)
2.501
2.502
V
REF
Figure 46. SHR Reference Voltage Shift
–200
–150
–100
–50
0
50
DISTORTION (ppm)
Figure 48. Thermal Hysteresis
Table 16. 24-Bit Input Shift Register Contents for Internal Reference Setup Command1
DB23 (MSB) DB22
DB21
DB20
DB19 to DB16
DB15 to DB1
DB0 (LSB)
0
1
1
1
X
X
1 or 0
Command bits (C3 to C0)
Address bits (don’t care)
Don’t care
Reference setup register
1 X = don’t care.
Rev. C | Page 22 of 24
Data Sheet
AD5316R
APPLICATIONS INFORMATION
For enhanced thermal, electrical, and board level performance,
solder the exposed pad on the bottom of the LFCSP package
to the corresponding thermal land paddle on the PCB. Design
thermal vias into the PCB land paddle area to further improve
heat dissipation.
MICROPROCESSOR INTERFACING
Microprocessor interfacing to the AD5316R is via a serial
bus that uses a standard protocol that is compatible with DSP
processors and microcontrollers. The communications channel
requires a 2-wire interface consisting of a clock signal and a
data signal.
The GND plane on the device can be increased (as shown in
Figure 50) to provide a natural heat sinking effect.
AD5316R TO ADSP-BF531 INTERFACE
The I2C interface of the AD5316R is designed for easy connec-
tion to industry-standard DSPs and microcontrollers. Figure 49
shows the AD5316R connected to the Analog Devices Blackfin®
processor. The Blackfin processor has an integrated I2C port
that can be connected directly to the I2C pins of the AD5316R.
AD5316R
GND
PLANE
AD5316R
BOARD
ADSP-BF531
GPIO1
GPIO2
SCL
SDA
Figure 50. Paddle Connection to Board
GALVANICALLY ISOLATED INTERFACE
PF9
PF8
LDAC
In many process control applications, it is necessary to provide
an isolation barrier between the controller and the unit being
controlled to protect and isolate the controlling circuitry from
any hazardous common-mode voltages that may occur.
RESET
Figure 49. AD5316R to ADSP-BF531 Interface
LAYOUT GUIDELINES
In any circuit where accuracy is important, careful consider-
ation of the power supply and ground return layout helps to
ensure the rated performance. The PCB on which the AD5316R
is mounted should be designed so that the AD5316R lies on the
analog plane.
The Analog Devices iCoupler® products provide voltage isolation
in excess of 2.5 kV. The serial loading structure of the AD5316R
makes the part ideal for isolated interfaces because the number of
interface lines is kept to a minimum. Figure 51 shows a 4-channel
isolated interface to the AD5316R using the ADuM1400. For
more information, visit http://www.analog.com/icouplers.
The AD5316R should have ample supply bypassing of 10 μF
in parallel with 0.1 μF on each supply, located as close to the
package as possible, ideally right up against the device. The 10 μF
capacitor is the tantalum bead type. The 0.1 μF capacitor should
have low effective series resistance (ESR) and low effective series
inductance (ESI), such as the common ceramic types; these
capacitors provide a low impedance path to ground at high
frequencies to handle transient currents due to internal logic
switching.
CONTROLLER
ADuM1400
V
V
V
V
V
V
V
V
IA
IB
IC
ID
OA
OB
OC
OD
TO
SERIAL
ENCODE
ENCODE
ENCODE
ENCODE
DECODE
DECODE
DECODE
DECODE
SCL
CLOCK IN
TO
SDA
SERIAL
DATA OUT
TO
RESET
RESET OUT
In systems where many devices are on one board, it is often
useful to provide some heat sinking capability to allow the
power to dissipate easily.
LOAD DAC
OUT
TO
LDAC
Figure 51. Isolated Interface
The AD5316R LFCSP models have an exposed pad beneath the
device. Connect this pad to the GND supply for the part. For
optimum performance, use special considerations to design the
motherboard and to mount the package.
Rev. C | Page 23 of 24
AD5316R
Data Sheet
OUTLINE DIMENSIONS
3.10
3.00 SQ
2.90
0.30
0.23
0.18
PIN 1
INDICATOR
PIN 1
INDICATOR
13
16
0.50
BSC
1
4
12
EXPOSED
PAD
1.75
1.60 SQ
1.45
9
8
5
0.50
0.40
0.30
0.25 MIN
TOP VIEW
BOTTOM VIEW
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
0.80
0.75
0.70
0.05 MAX
0.02 NOM
COPLANARITY
0.08
SECTION OF THIS DATA SHEET.
SEATING
PLANE
0.20 REF
COMPLIANT TO JEDEC STANDARDS MO-220-WEED-6.
Figure 52. 16-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
3 mm × 3 mm Body, Very Very Thin Quad
(CP-16-22)
Dimensions shown in millimeters
5.10
5.00
4.90
16
9
8
4.50
4.40
4.30
6.40
BSC
1
PIN 1
1.20
MAX
0.15
0.05
0.20
0.09
0.75
0.60
0.45
8°
0°
0.30
0.19
0.65
BSC
SEATING
PLANE
COPLANARITY
0.10
COMPLIANT TO JEDEC STANDARDS MO-153-AB
Figure 53. 16-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-16)
Dimensions shown in millimeters
ORDERING GUIDE
Reference
Temperature
Range
Accuracy
(INL)
Tempco
(ppm/°C)
Package
Description
Package
Model1
Resolution
10 Bits
10 Bits
10 Bits
Option
CP-16-22
RU-16
Branding
AD5316RBCPZ-RL7
AD5316RBRUZ
AD5316RBRUZ-RL7
EVAL-AD5316RDBZ
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
0.5 LSB
0.5 LSB
0.5 LSB
5 ꢀ(aꢁx
5 ꢀ(aꢁx
5 ꢀ(aꢁx
16-Lead LFCSP_WQ
16-Lead TSSOP
16-Lead TSSOP
Evaluation Board
DJT
RU-16
1 Z = RoHS Co(pliant Part.
I2C refers to a co((unications protocol originally developed by Philips Se(iconductors ꢀnow NXP Se(iconductorsx.
©2012–2017 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D10819-0-5/17(C)
Rev. C | Page 24 of 24
相关型号：
©2020 ICPDF网 联系我们和版权申明