AD7091 [ADI]
1 MSPS, Ultralow Power, 12-Bit ADC in 8-Lead LFCSP; 1 MSPS ,超低功耗, 12位ADC,采用8引脚LFCSP型号: | AD7091 |
厂家: | ADI |
描述: | 1 MSPS, Ultralow Power, 12-Bit ADC in 8-Lead LFCSP |
文件: | 总20页 (文件大小:448K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
1 MSPS, Ultralow Power,
12-Bit ADC in 8-Lead LFCSP
Data Sheet
AD7091
FEATURES
FUNCTIONAL BLOCK DIAGRAM
V
REGCAP
DD
Fast throughput rate of 1 MSPS
Specified for VDD of 2.09 V to 5.25 V
INL of 1 LSB maximum
AD7091
Analog input range of 0 V to VDD
Ultralow power
367 μA typical at 3 V and 1 MSPS
324 nA typical at 3 V in power-down mode
Reference provided by VDD
Flexible power/throughput rate management
High speed serial interface: SPI®-/QSPI™-/MICROWIRE®-/
DSP-compatible
SDO
SCLK
CS
12-BIT
SERIAL
INTERFACE
T/H
V
SAR
ADC
IN
CLK
OSC
CONVERSION
CONTROL LOGIC
CONVST
GND
Figure 1.
Busy indicator
Power-down mode
8-lead, 2 mm × 2 mm LFCSP package
Temperature range: −40°C to +125°C
1100
1000
900
800
700
600
500
400
300
200
100
0
V
= 3V
DD
APPLICATIONS
Battery-powered systems
Handheld meters
Medical instruments
Mobile communications
Instrumentation and control systems
Data acquisition systems
Optical sensors
Diagnostic/monitoring functions
Energy harvesting
0
200
400
600
800
1000
THROUGHPUT RATE (kSPS)
Figure 2. Power Dissipation vs. Throughput Rate
GENERAL DESCRIPTION
The AD7091 is a 12-bit successive approximation register
analog-to-digital converter (SAR ADC) that offers ultralow
power consumption (typically 367 μA at 3 V and 1 MSPS) while
achieving fast throughput rates (1 MSPS with a 50 MHz SCLK).
The AD7091 operates from a single 2.09 V to 5.25 V power
supply. The AD7091 also features an on-chip conversion clock
and a high speed serial interface.
The reference is derived internally from VDD. This design allows
the widest dynamic input range to the ADC; that is, the analog
input range for the AD7091 is from 0 V to VDD
.
PRODUCT HIGHLIGHTS
1. Lowest Power 12-Bit SAR ADC Available.
2. High Throughput Rate with Ultralow Power Consumption.
3. Flexible Power/Throughput Rate Management.
Average power scales with the throughput rate. Power-down
mode allows the average power consumption to be reduced
when the device is not performing a conversion.
4. Reference Derived from the Power Supply.
5. Single-Supply Operation.
The conversion process and data acquisition are controlled using
CONVST
a
signal and an internal oscillator. The AD7091 has a
serial interface that allows data to be read after the conversion
while achieving a 1 MSPS throughput rate. The AD7091 uses
advanced design and process techniques to achieve very low
power dissipation at high throughput rates.
Rev. A
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2012–2013 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
AD7091
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Converter Operation.................................................................. 10
ADC Transfer Function............................................................. 10
Typical Connection Diagram ................................................... 11
Analog Input ............................................................................... 11
Modes of Operation ................................................................... 12
Power Consumption .................................................................. 13
Multiplexer Applications........................................................... 14
Serial Interface ................................................................................ 15
Busy Indicator Enabled.............................................................. 15
Busy Indicator Disabled ............................................................ 16
Software Reset............................................................................. 17
Interfacing with an 8-/16-Bit SPI Bus...................................... 17
Outline Dimensions....................................................................... 18
Ordering Guide .......................................................................... 18
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description ......................................................................... 1
Product Highlights ........................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Timing Specifications .................................................................. 4
Absolute Maximum Ratings............................................................ 5
Thermal Resistance ...................................................................... 5
ESD Caution.................................................................................. 5
Pin Configuration and Function Descriptions............................. 6
Typical Performance Characteristics ............................................. 7
Terminology ...................................................................................... 9
Theory of Operation ...................................................................... 10
Circuit Information.................................................................... 10
REVISION HISTORY
6/13—Rev. 0 to Rev. A
Changes to Figure 22...................................................................... 13
Added Multiplexer Applications Section .................................... 14
Updated Outline Dimensions....................................................... 18
10/12—Revision 0: Initial Version
Rev. A | Page 2 of 20
Data Sheet
AD7091
SPECIFICATIONS
VDD = 2.09 V to 5.25 V, fSAMPLE = 1 MSPS, fSCLK = 50 MHz, TA = −40°C to +125°C, unless otherwise noted.
Table 1.
Parameter
DYNAMIC PERFORMANCE1
Signal-to-Noise Ratio (SNR)2
Test Conditions/Comments
fIN = 10 kHz sine wave
VDD < 2.7 V
Min
Typ
Max
Unit
68
69
68
dB
dB
dB
VDD ≥ 2.7 V
67
66.3
Signal-to-Noise-and-Distortion Ratio
(SINAD)2
Total Harmonic Distortion (THD)2
Spurious-Free Dynamic Range (SFDR)2
Aperture Delay2
−86
−85
5
40
1.5
1.2
−74
−75
dB
dB
ns
ps
MHz
MHz
Aperture Jitter2
Full Power Bandwidth2
At −3 dB
At −0.1 dB
DC ACCURACY
Resolution
12
Bits
LSB
LSB
LSB
LSB
LSB
Integral Nonlinearity (INL)2
Differential Nonlinearity (DNL)2
Offset Error2
0.6
0.3
0.7
1.2
1.1
1
0.9
+5
4
Guaranteed no missing codes to 12 bits
−8.5
Gain Error2
Total Unadjusted Error (TUE)2
ANALOG INPUT
Input Voltage Range
DC Leakage Current
Input Capacitance3
0
VDD
1
V
µA
pF
pF
During acquisition phase
Outside acquisition phase
7
1
LOGIC INPUTS
Input High Voltage (VINH
)
0.7 × VDD
V
Input Low Voltage (VINL
Input Current (IIN)
)
0.3 × VDD
1
5
V
µA
pF
Typically 10 nA, VIN = 0 V or VDD
Input Capacitance (CIN)3
LOGIC OUTPUTS
Output High Voltage (VOH
)
ISOURCE = 200 µA
ISINK = 200 µA
VDD − 0.2
V
V
µA
pF
Output Low Voltage (VOL
)
0.4
1
5
Floating State Leakage Current
Floating State Output Capacitance3
Output Coding
Straight binary
CONVERSION RATE
Conversion Time
650
350
1
ns
ns
MSPS
Track-and-Hold Acquisition Time2, 3
Full-scale step input
Throughput Rate
POWER REQUIREMENTS
VDD
2.09
5.25
V
IDD
VIN = 0 V
VDD = 5.25 V
Normal Mode—Static4
9.3
9.1
27
28
554
442
µA
µA
µA
µA
µA
µA
µA
µA
VDD = 3 V
Normal Mode—Operational
Power-Down Mode
VDD = 5.25 V, fSAMPLE = 1 MSPS
VDD = 3 V, fSAMPLE = 1 MSPS
VDD = 3 V, fSAMPLE = 100 kSPS
VDD = 5.25 V
450
367
45
0.374
0.324
0.324
8.2
8
1.8
VDD = 3 V
VDD = 3 V, TA = −40°C to +85°C
Rev. A | Page 3 of 20
AD7091
Data Sheet
Parameter
Test Conditions/Comments
VIN = 0 V
VDD = 5.25 V
Min
Typ
Max
Unit
Power Dissipation
Normal Mode—Static4
50
27
2.4
1.1
2
142
84
3
1.4
44
24
µW
µW
mW
mW
µW
µW
VDD = 3 V
Normal Mode—Operational
Power-Down Mode
VDD = 5.25 V, fSAMPLE = 1 MSPS
VDD = 3 V, fSAMPLE = 1 MSPS
VDD = 5.25 V
VDD = 3 V
1
1 Dynamic performance is achieved when SCLK operates in burst mode. Operating a free running SCLK during the acquisition phase degrades dynamic performance.
2 See the Terminology section.
3 Sample tested during initial release to ensure compliance.
4 SCLK is operating in burst mode and is idling high. With a free running SCLK and pulled low, the IDD static current is increased by 60 µA typical at VDD = 5.25 V.
CS
CS
TIMING SPECIFICATIONS
VDD = 2.09 V to 5.25 V, TA = −40°C to +125°C, unless otherwise noted. Signals are specified from 10% to 90% of VDD with a load
capacitance of 12 pF on the output pin.1
Table 2.
Parameter
Limit at TMIN, TMAX
Unit
Description
fSCLK
t1
t2
t3
t4
t5
t6
t7
50
8
7
0.4 tSCLK
3
0.4 tSCLK
15
10
650
6
MHz max
ns max
ns max
ns min
ns min
ns min
ns max
ns min
ns max
ns min
ns max
ns min
ns min
µs max
ns min
Frequency of serial read clock
Delay from the end of a conversion until SDO exits the three-state condition
Data access time after SCLK falling edge
SCLK high pulse width
SCLK to data valid hold time
SCLK low pulse width
SCLK falling edge to SDO high impedance
CONVST pulse width
t8
t9
Conversion time
CS low time before the end of a conversion
Delay from CS falling edge until SDO exits the three-state condition
CS high time before the end of a conversion
Delay from the end of a conversion until the CS falling edge
Power-up time
t10
t11
t12
t13
tQUIET
18
8
8
100
50
Time between the last SCLK edge and the next CONVST pulse
1 Sample tested during initial release to ensure compliance.
Rev. A | Page 4 of 20
Data Sheet
AD7091
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
THERMAL RESISTANCE
Table 3.
Table 4. Thermal Resistance
Parameter
Rating
Package Type
θJA
θJC
Unit
VDD to GND
−0.3 V to +7 V
−0.3 V to VDD + 0.3 V
−0.3 V to VDD + 0.3 V
−0.3 V to VDD + 0.3 V
10 mA
8-Lead LFCSP
36.67
6.67
°C/W
Analog Input Voltage to GND
Digital Input Voltage to GND
Digital Output Voltage to GND
Input Current to Any Pin Except
Supplies1
ESD CAUTION
Operating Temperature Range
Storage Temperature Range
Junction Temperature
ESD
−40°C to +125°C
−65°C to +150°C
150°C
Human Body Model (HBM)
Field-Induced Charged Device
Model (FICDM)
2.5 kV
1.5 kV
1 Transient currents of up to 100 mA do not cause silicon controlled rectifier
(SCR) latch-up.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. A | Page 5 of 20
AD7091
Data Sheet
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
V
1
2
3
4
8
7
SDO
DD
AD7091
V
SCLK
IN
TOP VIEW
6 CS
REGCAP
GND
(Not to Scale)
5 CONVST
NOTES
1. THE EXPOSED PAD IS NOT CONNECTED
INTERNALLY. FOR INCREASED
RELIABILITY OF THE SOLDER JOINTS
AND FOR MAXIMUM THERMAL CAPABILITY,
SOLDER THE EXPOSED PAD TO THE
SUBSTRATE, GND.
Figure 3. Pin Configuration
Table 5. Pin Function Descriptions
Pin No.
Mnemonic
Description
1
VDD
Power Supply Input. The VDD range is from 2.09 V to 5.25 V. Decouple this supply pin to GND. Typical recom-
mended capacitor values are 10 µF and 0.1 µF.
2
3
VIN
REGCAP
Analog Input. The single-ended analog input range is from 0 V to VDD.
Decoupling Capacitor Pin for Voltage Output from Internal Low Dropout (LDO) Regulator. Decouple this output
pin separately to GND using a 1 μF capacitor. The voltage at this pin is 1.8 V typical.
4
5
6
GND
Ground. This pin is the ground reference point for all circuitry on the AD7091. The analog input signal should
be referred to this GND voltage.
Conversion Start. Active low, edge triggered logic input. The falling edge of CONVST places the track-and-hold
into hold mode and initiates a conversion.
Chip Select. Active low logic input. The serial bus is enabled when CS is held low; in this mode CS is used to frame
the output data on the SPI bus.
CONVST
CS
7
8
SCLK
SDO
Serial Clock. This pin acts as the serial clock input.
Serial Data Output. The conversion output data is supplied to this pin as a serial data stream. The bits are
clocked out on the falling edge of the SCLK input. The data is provided MSB first.
9
EPAD
Exposed Pad. The exposed pad is not connected internally. For increased reliability of the solder joints and for
maximum thermal capability, solder the exposed pad to the substrate, GND.
Rev. A | Page 6 of 20
Data Sheet
AD7091
TYPICAL PERFORMANCE CHARACTERISTICS
0
72
70
68
66
64
62
60
T
= 25°C
V
T
= 3V
fIAN = 10kHz
fSAAMPLE = 1MSPS
DD
V
= 5V
= 3V
= 25°C
DD
–20
–40
fSAMPLE = 1MSPS
SNR = 69.84dB
SINAD = 69.56dB
THD = –81.05dB
V
= 2.7V
DD
V
DD
–60
–80
–100
–120
–140
0
100
200
300
400
500
1
10
INPUT FREQUENCY (kHz)
100
FREQUENCY (kHz)
Figure 4. Typical Dynamic Performance
Figure 7. SNR vs. Analog Input Frequency for Various Supply Voltages
1.0
0.8
0
T
= 25°C
V
T
= 3V
= 25°C
fSAAMPLE = 1MSPS
DD
fSAAMPLE = 1MSPS
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
0.6
0.4
0.2
0
–0.2
–0.4
–0.6
–0.8
–1.0
V
= 3V
DD
V
= 2.7V
DD
0
512
1024
1536
2048
2560
3072
3584
4096
1
10
100
CODE
INPUT FREQUENCY (kHz)
Figure 8. THD vs. Analog Input Frequency for Various Supply Voltages
Figure 5. Typical INL Performance
–50
1.0
0.8
V
T
= 3V
V
T
= 3V
= 25°C
fIAN = 10kHz
DD
= 25°C
DD
fSAAMPLE = 1MSPS
–55
–60
–65
–70
–75
–80
–85
–90
fSAMPLE = 1MSPS
0.6
0.4
0.2
0
–0.2
–0.4
–0.6
–0.8
–1.0
0
512
1024
1536
2048
2560
3072
3584
4096
10
100
1000
10000
CODE
SOURCE IMPEDANCE (Ω)
Figure 6. Typical DNL Performance
Figure 9. THD vs. Source Impedance
Rev. A | Page 7 of 20
AD7091
Data Sheet
75
T
550
500
450
400
350
300
250
= 25°C
fSAAMPLE = 1MSPS
fSAMPLE = 1MSPS
V
= 2.7V
= 3V
DD
70
65
60
55
50
+125°C
V
DD
V
= 5V
DD
+85°C
+25°C
–40°C
1
10
INPUT FREQUENCY (kHz)
100
2.25 2.50 2.75 3.00 3.25 3.50 3.75 4.00 4.25 4.50 4.75 5.00
SUPPLY VOLTAGE (V)
Figure 13. Operational Supply Current vs. Supply Voltage
for Various Temperatures
Figure 10. SINAD vs. Analog Input Frequency for Various Supply Voltages
60
6000
5000
4000
3000
2000
1000
0
V
A
= 3.3V
V
V
V
V
= 2.09V
= 3V
= 3.6V
= 5.25V
DD
= 25°C
DD
DD
DD
DD
T
51,436
65,536 SAMPLES
50
40
30
20
10
0
8108
2048
5992
0
0
2047
2049
2050
2051
–40
25
85
125
CODE
TEMPERATURE (°C)
Figure 11. Histogram of Codes at Code Center (VDD/2)
Figure 14. Power-Down Supply Current vs. Temperature
for Various Supply Voltages
7
+125°C
6
5
4
3
+25°C
–40°C
2
1
0
V
= 3V
DD
10
20
30
40
50
SDO CAPACITANCE LOAD (pF)
Figure 12. t2 Delay vs. SDO Capacitance Load, VDD = 3 V
Rev. A | Page 8 of 20
Data Sheet
AD7091
TERMINOLOGY
Integral Nonlinearity (INL)
Signal-to-Noise-and-Distortion Ratio (SINAD)
INL is the maximum deviation from a straight line passing
through the endpoints of the ADC transfer function. For the
AD7091, the endpoints of the transfer function are zero scale
(a point 0.5 LSB below the first code transition) and full scale
(a point 0.5 LSB above the last code transition).
SINAD is the measured ratio of signal to noise and distortion
at the output of the ADC. The signal is the rms value of the sine
wave, and noise is the rms sum of all nonfundamental signals up
to half the sampling frequency (fSAMPLE/2), including harmonics,
but excluding dc.
Differential Nonlinearity (DNL)
Total Unadjusted Error (TUE)
DNL is the difference between the measured and the ideal
1 LSB change between any two adjacent codes in the ADC.
TUE is a comprehensive specification that includes the gain,
linearity, and offset errors.
Offset Error
Total Harmonic Distortion (THD)
Offset error is the deviation of the first code transition (00 … 000
to 00 … 001) from the ideal (such as GND + 0.5 LSB).
THD is the ratio of the rms sum of harmonics to the funda-
mental. For the AD7091, THD is defined as
Gain Error
2
2
2
2
2
V2 +V3 +V4 +V5 +V6
THD dB = 20 log
( )
Gain error is the deviation of the last code transition (111 … 110
to 111 … 111) from the ideal (such as VDD − 1.5 LSB) after the
offset error has been adjusted out.
V1
where:
V1 is the rms amplitude of the fundamental.
V2, V3, V4, V5, and V6 are the rms amplitudes of the second
Track-and-Hold Acquisition Time
The track-and-hold amplifier returns to track mode after the
end of a conversion. The track-and-hold acquisition time is the
time required for the output of the track-and-hold amplifier to
reach its final value, within 0.5 LSB, after a conversion.
through the sixth harmonics.
Spurious-Free Dynamic Range (SFDR)
SFDR, also known as peak harmonic or spurious noise, is defined
as the ratio of the rms value of the next largest component in the
ADC output spectrum (up to fSAMPLE/2 and excluding dc) to the
rms value of the fundamental.
Signal-to-Noise Ratio (SNR)
SNR is the measured ratio of signal to noise at the output of the
ADC. The signal is the rms amplitude of the fundamental. Noise
is the sum of all nonfundamental signals up to half the sampling
frequency (fSAMPLE/2), excluding dc.
Aperture Delay
Aperture delay is the measured interval between the leading edge of
the sampling clock and the point at which the ADC samples data.
The ratio is dependent on the number of quantization levels in the
digitization process: the more levels, the smaller the quantization
noise. The theoretical signal-to-noise ratio for an ideal N-bit
converter with a sine wave input is given by
Aperture Jitter
Aperture jitter is the sample-to-sample variation in the effective
point in time at which the data is sampled.
Full Power Bandwidth
Signal-to-Noise Ratio = (6.02N + 1.76) dB
Full power bandwidth is the input frequency at which the ampli-
tude of the reconstructed fundamental is reduced by 0.1 dB or
3 dB for a full-scale input.
Therefore, for a 12-bit converter, the SNR is 74 dB.
Rev. A | Page 9 of 20
AD7091
Data Sheet
THEORY OF OPERATION
When the ADC starts a conversion, SW2 opens and SW1 moves
to Position B, causing the comparator to become unbalanced (see
Figure 16). The control logic and the charge redistribution DAC
are used to add and subtract fixed amounts of charge from the
sampling capacitor to bring the comparator back into a balanced
condition. When the comparator is rebalanced, the conversion
is complete. The control logic generates the ADC output code.
Figure 17 shows the ADC transfer function.
CIRCUIT INFORMATION
The AD7091 is a 12-bit successive approximation register
analog-to-digital converter (SAR ADC) that offers ultralow
power consumption (typically 367 µA at 3 V and 1 MSPS) while
achieving fast throughput rates (1 MSPS with a 50 MHz SCLK).
The part operates from a single power supply in the range of
2.09 V to 5.25 V.
The AD7091 provides an on-chip track-and-hold amplifier
and an analog-to-digital converter (ADC) with a serial interface
housed in a tiny 8-lead LFCSP package. This package offers
considerable space-saving advantages compared with alternative
solutions. The serial clock input accesses data from the part. The
clock for the SAR ADC is generated internally.
CHARGE
REDISTRIBUTION
DAC
SAMPLING
CAPACITOR
A
V
IN
CONTROL
LOGIC
SW1
B
SW2
CONVERSION
PHASE
COMPARATOR
The analog input range is 0 V to VDD. An external reference is
not required for the ADC, nor is there a reference on chip. The
reference voltage for the AD7091 is derived from the power
supply and, thus, provides the widest dynamic input range of
GND
LDO/2
Figure 16. ADC Conversion Phase
ADC TRANSFER FUNCTION
0 V to VDD
.
The output coding of the AD7091 is straight binary. The designed
code transitions occur midway between successive integer LSB
values, such as 0.5 LSB, 1.5 LSB, and so on. The LSB size for the
AD7091 is VDD/4096. The ideal transfer characteristic for the
AD7091 is shown in Figure 17.
The AD7091 also features a power-down option to save power
between conversions. The power-down feature is implemented
using the standard serial interface, as described in the Modes of
Operation section.
CONVERTER OPERATION
111 ... 111
111 ... 110
The AD7091 is a SAR ADC based around a charge redistribu-
tion DAC. Figure 15 and Figure 16 show simplified schematics
of the ADC.
111 ... 000
1LSB = V
DD
/4096
011 ... 111
Figure 15 shows the ADC during its acquisition phase; SW2 is
closed and SW1 is in Position A. The comparator is held in a
balanced condition, and the sampling capacitor acquires the
signal on VIN.
000 ... 010
000 ... 001
000 ... 000
1LSB
V
– 1LSB
DD
0V
ANALOG INPUT
CHARGE
REDISTRIBUTION
DAC
Figure 17. AD7091 Transfer Characteristic
SAMPLING
CAPACITOR
A
V
IN
CONTROL
LOGIC
SW1
B
ACQUISITION
PHASE
SW2
COMPARATOR
GND
LDO/2
Figure 15. ADC Acquisition Phase
Rev. A | Page 10 of 20
Data Sheet
AD7091
V
DD
TYPICAL CONNECTION DIAGRAM
Figure 19 shows a typical connection diagram for the AD7091.
A positive power supply in the range of 2.09 V to 5.25 V should
be connected to the VDD pin. The reference is derived internally
from VDD and, for this reason, VDD should be well decoupled to
achieve the specified performance; typical values for the decoupling
capacitors are 100 nF and 10 μF. The analog input range is 0 V
to VDD. The typical value for the regulator bypass decoupling
capacitor (REGCAP) is 1 μF. The conversion result is output in
a 12-bit word with the MSB first.
D1
C2
3.6pF
R1
V
IN
C1
1pF
C3
2.5pF
D2
NOTES
1. DURING THE CONVERSION PHASE, THE SWITCH IS OPEN.
DURING THE TRACK PHASE, THE SWITCH IS CLOSED.
Figure 18. Equivalent Analog Input Circuit
Alternatively, because the supply current required by the AD7091
is so low, a precision reference can be used as the supply source
to the part. A reference from the REF19x or ADR34xx voltage
reference family (REF195 or ADR3450 for 5 V, and REF193 or
ADR3430 for 3 V) can be used to supply the required voltage
to the ADC. This configuration is especially useful if the power
supply is quite noisy, or if the system supply voltages are at some
value other than 5 V or 3 V, such as 15 V.
Capacitor C1 in Figure 18 is typically about 1 pF and can
primarily be attributed to pin capacitance. Resistor R1 is a
lumped component made up of the on resistance of a switch.
This resistor is typically about 500 Ω. Capacitor C2 is the ADC
sampling capacitor and typically has a capacitance of 3.6 pF.
In applications where harmonic distortion and signal-to-noise
ratio (SNR) are critical, the analog input should be driven from
a low impedance source. Large source impedances significantly
affect the ac performance of the ADC and may necessitate the
use of an input buffer amplifier, as shown in Figure 19. The choice
of the op amp is a function of the particular application.
If the busy indicator function is required, connect a pull-up
resistor of typically 100 kΩ to VDD to the SDO pin (see Figure 19).
In addition, for applications in which power consumption is
a concern, the power-down mode can be used to improve the
power performance of the ADC (see the Modes of Operation
section for more information).
When no amplifier is used to drive the analog input, the source
impedance should be limited to low values. The maximum source
impedance depends on the amount of total harmonic distortion
(THD) that can be tolerated. The THD increases as the source
impedance increases and performance degrades. Figure 9 shows
a graph of THD vs. source impedance when using a supply
voltage of 3 V and a sampling rate of 1 MSPS.
ANALOG INPUT
Figure 18 shows an equivalent circuit of the AD7091 analog
input structure. The D1 and D2 diodes provide ESD protection
for the analog input. To prevent the diodes from becoming
forward-biased and conducting current, ensure that the analog
input signal never exceeds VDD by more than 300 mV. These diodes
can conduct a maximum of 10 mA without causing irreversible
damage to the part.
To achieve the specified performance, use an external filter—such
as the one-pole, low-pass RC filter shown in Figure 19—on the
analog input connected to the AD7091.
WITH BUSY
INDICATOR
V
DD
V
DD
(2.09V to 5.25V)
10μF
1μF
100nF
100kΩ
V
REGCAP
DD
SDO
51Ω
MICROPROCESSOR/
MICROCONTROLLER/
DSP
V
IN
ANALOG
INPUT
SCLK
AD7091
4.7nF
CS
CONVST
GND
Figure 19. Typical Connection Diagram
Rev. A | Page 11 of 20
AD7091
Data Sheet
To read back data stored in the conversion result register, wait until
MODES OF OPERATION
CS
the conversion is complete, and then pull
low. The conversion
The mode of operation of the AD7091 is selected by controlling
data is subsequently clocked out on the SDO pin (see Figure 20).
Because the output shift register is 12 bits wide, data is shifted out
of the device as a 12-bit word under the control of the serial clock
input (SCLK). After reading back the data, the user can pull
CONVST
the logic level of the
signal when a conversion is complete.
The two modes of operation are normal mode and power-down
mode. These modes of operation provide flexible power manage-
ment options, allowing optimization of the power dissipation to
throughput rate ratio for different application requirements.
CONVST
low again to start another conversion after the tQUIET
time has elapsed.
CONVST
The logic level of the
pin at the end of a conversion
Power-Down Mode
determines whether the AD7091 remains in normal mode or
enters power-down mode (see the Normal Mode section and the
Power-Down Mode section). Similarly, if the device is in power-
The power-down mode of operation is intended for use in applica-
tions where slower throughput rates and lower power consumption
are required. In this mode, the ADC can be powered down after
each conversion or after a series of conversions performed at a
high throughput rate, with the ADC powered down for relatively
long durations between these bursts of several conversions. When
the AD7091 is in power-down mode, the serial interface remains
active even though all analog circuitry is powered down.
CONVST
down mode,
controls whether the device returns to
normal mode or remains in power-down mode.
Normal Mode
The normal mode of operation is intended to achieve the fastest
throughput rate performance. In normal mode, the AD7091
remains fully powered at all times, so power-up times are not
a concern. Figure 20 shows the general timing diagram of the
AD7091 in normal mode.
CONVST
To enter power-down mode, pull
low and keep it low
prior to the end of a conversion (denoted as EOC in Figure 21).
CONVST
After the conversion is complete, the logic level of the
In normal mode, the conversion is initiated on the falling edge of
CONVST
pin is tested. If the
power-down mode.
signal is logic low, the part enters
CONVST
, as described in the Serial Interface section. To ensure
CONVST
that the part remains fully powered at all times,
return high after t7 and remain high until the conversion is com-
plete. At the end of a conversion (denoted as EOC in Figure 20),
must
The serial interface of the AD7091 is functional in power-down
mode; therefore, users can read back the conversion result after
the part enters power-down mode.
CONVST
the logic level of
is tested.
EOC
t7
CONVST
CS
t8
t12
t10
SDO
CONVERSION DATA
NOTES
1.
IS DON’T CARE.
2. EOC IS THE END OF A CONVERSION.
Figure 20. Normal Mode of Operation, Serial Interface Read Timing
EOC
POWER-DOWN MODE
CONVST
t13
t8
t12
CS
t10
SDO
CONVERSION DATA
NOTES
1.
IS DON’T CARE.
2. EOC IS THE END OF A CONVERSION.
Figure 21. Entering and Exiting Power-Down Mode
Rev. A | Page 12 of 20
Data Sheet
AD7091
To exit power-down mode and power up the AD7091, pull
The contribution to the total power dissipated by the normal
mode static operation is
CONVST
CONVST
high at any time. On the rising edge of
, the
device begins to power up. The power-up time of the AD7091
is 100 µs. To start the next conversion, operate the interface as
described in the Normal Mode section.
9.1 μA × 3 V = 27 μW
Therefore, the total power dissipated at 500 kSPS is
537 μW + 27 μW = 564 μW
POWER CONSUMPTION
Power Consumption Using a Combination of Normal
Mode and Power-Down Mode
The two modes of operation for the AD7091—normal mode
and power-down mode (see the Modes of Operation section for
more information)—produce different power vs. throughput
rate performances. Using a combination of normal mode and
power-down mode achieves the optimum power performance.
A combination of normal mode and power-down mode
achieves the optimum power performance. This operation
can be performed at constant sampling rates of <10 kSPS.
Figure 22 shows the AD7091 conversion sequence using a
combination of normal mode and power-down mode with a
throughput of 5 kSPS. With a VDD supply voltage of 3 V, the
static current is 9.1 μA. The dynamic current is 357.9 μA at
1 MSPS. The current consumption during power-down mode
is 324 nA. A conversion takes typically 650 ns to complete, and
the AD7091 takes 100 μs to power up from power-down mode.
To achieve optimum static current consumption, SCLK should
CS
be in burst mode and
should idle high. Failure to adhere to
these guidelines results in increased static current.
Improved power consumption for the AD7091 can also be
achieved by carefully selecting the VDD supply (see Figure 13).
Power Consumption in Normal Mode
With a 3 V VDD supply and a throughput rate of 1 MSPS, the IDD
current consumption for the part in normal operational mode is
367 μA (composed of 9.1 μA of static current and 357.9 μA of
dynamic current during conversion). The dynamic current con-
sumption is directly proportional to the throughput rate.
The dynamic conversion time contributes 5 μW to the overall
power dissipation as follows:
((5 kSPS/1 MSPS) × 357.9 μA) × 3 V = 5 μW
The contribution to the total power dissipated by the normal
mode static operation and the power-down mode is
The following example calculates the power consumption of
the AD7091 when operating in normal mode with a 500 kSPS
throughput rate and a 3 V supply.
(((100 μs + 650 ns)/200 μs) × 9.1 μA) × 3 V +
((99.4 μs/200 μs) × 324 nA) × 3 V = 14 μW
Therefore, the total power dissipated at 5 kSPS is
5 μW + 14 μW = 19 μW
The dynamic conversion time contributes 537 μW to the overall
power dissipation as follows:
((500 kSPS/1 MSPS) × 357.9 μA) × 3 V = 537 μW
EOC
CONVST
99μs
POWER-DOWN
100μs
POWER-UP
650ns
CONVERSION
CS
SDO
DATA
200μs
NOTES
1. EOC IS THE END OF A CONVERSION.
Figure 22. Conversion Sequence with Normal Mode and Power-Down Mode, 5 kSPS Throughput
Rev. A | Page 13 of 20
AD7091
Data Sheet
Figure 23 and Figure 24 show the typical power dissipation
vs. throughput rate for the AD7091 at 3 V for the VDD supply.
Figure 24 shows the reduction in power consumption that can
be achieved when power-down mode is used compared with
using only normal mode at lower throughput rates.
1100
MULTIPLEXER APPLICATIONS
A multiplexer can be used in the signal chain to switch multiple
analog input signals to the AD7091. In such applications,
control the multiplexer switch time to ensure accurate analog-
to digital-conversion of the input signals. To allow the AD7091
to fully acquire the input signal, the multiplexer should
switch in the channel to be converted a minimum of 350 ns
before initiating a conversion. The multiplexer should also
hold this channel at the AD7091 for a minimum of 200 ns after
V
= 3V
DD
1000
900
800
700
600
500
400
300
200
100
0
CONVST
the
falling edge.
0
200
400
600
800
1000
THROUGHPUT RATE (kSPS)
Figure 23. Power Dissipation vs. Throughput Rate (Full Range)
100
V
(NO PD)
DD
V
DD
10
V
V
= 3V
DD
= 0V
IN
1
0.01
0.1
1
10
100
THROUGHPUT RATE (kSPS)
Figure 24. Power Dissipation vs. Throughput Rate (Lower Range)
Rev. A | Page 14 of 20
Data Sheet
AD7091
SERIAL INTERFACE
The AD7091 serial interface consists of four signals: SCLK,
The busy indicator allows the host to detect when the SDO
CONVST
CS
pin exits the three-state condition after the end of a conversion.
When the busy indicator is enabled, 13 SCLK cycles are required:
12 clock cycles to propagate the data and an additional clock cycle
to return the SDO pin to the three-state condition.
SDO,
, and . The serial interface is used to access
data from the result register and to control the modes of oper-
ation of the device.
The SCLK pin is the serial clock input for the device.
The SDO pin outputs the conversion result; data transfers
take place with respect to SCLK.
To enable the busy indicator feature, a conversion must first
CONVST
be started. A high-to-low transition on
initiates a
conversion. This transition places the track-and-hold into hold
mode and samples the analog input at this point. If the user does
CONVST
The
pin is used to initiate the conversion process
and to select the mode of operation of the AD7091 (see the
Modes of Operation section).
CONVST
not want the AD7091 to enter power-down mode,
should be taken high before the end of the conversion.
CS
CS
The
takes the SDO line out of a high impedance state. A rising
CS
pin is used to frame the data. The falling edge of
A conversion requires 650 ns to complete. When the conversion
process is finished, the track-and-hold returns to track mode.
edge on
returns the SDO line to a high impedance state.
CS
CS
Before the end of a conversion, pull
indicator (see Figure 26).
low to enable the busy
The logic level of at the end of a conversion determines
whether the busy indicator is enabled. This feature affects the
propagation of the MSB with respect to
The conversion result is shifted out of the device as a 12-bit
CS
CS
and SCLK.
word under the control of SCLK and the logic level of
at the
BUSY INDICATOR ENABLED
end of a conversion. At the end of a conversion, SDO is driven
low. SDO remains low until the MSB (DB11) of the conversion
result is clocked out on the first falling edge of SCLK. DB10 to
DB0 are shifted out on the subsequent falling edges of SCLK.
The 13th SCLK falling edge returns SDO to a high impedance
state. Data is propagated on SCLK falling edges and is valid on
both the rising and falling edges of the next SCLK. The timing
diagram for this operation is shown in Figure 26.
When the busy indicator is enabled, the SDO pin can be used as
an interrupt signal to indicate that a conversion is complete. The
connection diagram for this configuration is shown in Figure 25.
Note that a pull-up resistor to VDD is required on the SDO pin.
CS1
CONVERT
V
DD
DIGITAL HOST
100kΩ
CS
CONVST
SDO
CONVST
If another conversion is required, pull
repeat the cycle.
low again and
DATA IN
AD7091
SCLK
IRQ
CLK
Figure 25. Connection Diagram with Busy Indicator
EOC
t7
CONVST
CS
tQUIET
t8
t9
t3
3
4
5
10
11
t5
1
2
12
SCLK
SDO
13
t1
t6
t2
t4
DB0
DB11
DB10
DB9
DB8
DB7
DB2
DB1
THREE-STATE
THREE-STATE
NOTES
1. EOC IS THE END OF A CONVERSION.
Figure 26. Serial Port Timing with Busy Indicator
Rev. A | Page 15 of 20
AD7091
Data Sheet
The conversion result is shifted out of the device as a 12-bit
CS
BUSY INDICATOR DISABLED
word under the control of SCLK and . The MSB (Bit DB11)
To operate the AD7091 without the busy indicator, a conversion
must first be started. A high-to-low transition on
ates a conversion. This transition places the track-and-hold into
hold mode and samples the analog input at this point. If the user
does not want the AD7091 to enter power-down mode,
should be taken high before the end of the conversion.
CS
is clocked out on the falling edge of . DB10 to DB0 are shifted
CONVST
initi-
out on the subsequent falling edges of SCLK. The 12th SCLK
falling edge returns SDO to a high impedance state. After all the
CS
data is clocked out, pull
high again. Data is propagated on
CONVST
SCLK falling edges and is valid on both the rising and falling
edges of the next SCLK. The timing diagram for this operation
is shown in Figure 27.
A conversion requires 650 ns to complete. When the conversion
process is finished, the track-and-hold returns to track mode. To
prevent the busy indicator from becoming enabled, ensure that
CONVST
If another conversion is required, pull
repeat the cycle.
low again and
CS
is pulled high before the end of the conversion (see Figure 27).
EOC
t7
CONVST
tQUIET
t8
t12
CS
t11
t3
5
1
2
3
4
10
11
12
SCLK
t5
t6
t10
t2
t4
SDO
DB11
DB10
DB9
DB8
DB7
DB2
DB1
DB0
THREE-STATE
THREE-STATE
NOTES
1. EOC IS THE END OF A CONVERSION.
Figure 27. Serial Port Timing Without Busy Indicator
Rev. A | Page 16 of 20
Data Sheet
AD7091
SOFTWARE RESET
INTERFACING WITH AN 8-/16-BIT SPI BUS
The AD7091 requires the user to initiate a software reset upon
power-up. Note that failure to apply the correct software reset
command may result in a device malfunction. The timing
diagram for the software reset operation is shown in Figure 28.
It is also possible to interface the AD7091 with a conventional
8-/16-bit SPI bus.
Performing conversions and reading results can be achieved by
configuring the host SPI interface for 16 bits, which results in
providing an additional four SCLK cycles to complete a conver-
sion compared with the standard interface methods (see the
Busy Indicator Enabled section and the Busy Indicator Disabled
section).
After the 13th SCLK falling edge with the busy indicator enabled
or after the 12th SCLK falling edge with the busy indicator disabled,
SDO returns to a high impedance state. The additional four bits
should be treated as don’t care bits by the host. All other timings
are as shown in Figure 26 and Figure 27, with tQUIET starting after
the 16th SCLK cycle.
To issue a software reset,
CONVST
1. Start a conversion by pulling
low.
CS
2. Read back the conversion result by pulling
conversion is complete.
low after the
CS
3. Between the second and eighth SCLK cycles, pull
to short cycle the read operation.
high
4. At the end of the next conversion, the software reset is
executed.
As soon as a software reset is issued, the user can start another
CONVST
conversion by pulling
low.
A software reset can be performed by configuring the SPI bus for
eight bits and performing the operation described in the Software
Reset section.
EOC/
SOFTWARE
RESET
EOC
t7
t7
CONVST
t8
t8
t12
CS
t10
SDO
SHORT CYCLE READ
t3
SCLK
1
2
6
7
8
t5
NOTES
1. EOC IS THE END OF A CONVERSION.
Figure 28. Software Reset Timing
Rev. A | Page 17 of 20
AD7091
Data Sheet
OUTLINE DIMENSIONS
1.70
1.60
1.50
2.10
2.00 SQ
1.90
0.50 BSC
8
5
0.15 REF
PIN 1 INDEX
EXPOSED
PAD
1.10
1.00
0.90
AREA
0.425
0.350
0.275
4
1
PIN 1
INDICATOR
(R 0.15)
TOP VIEW
BOTTOM VIEW
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
0.60
0.55
0.50
0.05 MAX
0.02 NOM
SECTION OF THIS DATA SHEET.
SEATING
PLANE
0.30
0.25
0.20
0.20 REF
Figure 29. 8-Lead Lead Frame Chip Scale Package [LFCSP_UD]
2.00 mm × 2.00 mm Body, Ultra Thin, Dual Lead
(CP-8-10)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
AD7091BCPZ-RL
AD7091BCPZ-RL7
EVAL-AD7091SDZ
EVAL-SDP-CB1Z
Temperature Range
−40°C to +125°C
−40°C to +125°C
Package Description
Package Option
Branding
8-Lead Lead Frame Chip Scale Package [LFCSP_UD]
8-Lead Lead Frame Chip Scale Package [LFCSP_UD]
Evaluation Board
CP-8-10
CP-8-10
92
92
Evaluation Controller Board
1 Z = RoHS Compliant Part.
Rev. A | Page 18 of 20
Data Sheet
NOTES
AD7091
Rev. A | Page 19 of 20
AD7091
NOTES
Data Sheet
©2012–2013 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D10996-0-6/13(A)
Rev. A | Page 20 of 20
相关型号:
©2020 ICPDF网 联系我们和版权申明