AD7175-8BCPZ-RL7 [ADI]
24-Bit, 8-/16-Channel, 250 kSPS, Sigma-Delta ADC with True Rail-to-Rail Buffers;![AD7175-8BCPZ-RL7](http://pdffile.icpdf.com/pdf2/p00260/img/icpdf/AD7175-8BCPZ_1571945_icpdf.jpg)
型号: | AD7175-8BCPZ-RL7 |
厂家: | ![]() |
描述: | 24-Bit, 8-/16-Channel, 250 kSPS, Sigma-Delta ADC with True Rail-to-Rail Buffers 转换器 |
文件: | 总65页 (文件大小:1052K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
24-Bit, 8-/16-Channel, 250 kSPS, Sigma-
Delta ADC with True Rail-to-Rail Buffers
AD7175-8
Data Sheet
FEATURES
GENERAL DESCRIPTION
Fast and flexible output rate: 5 SPS to 250 kSPS
The AD7175-8 is a low noise, fast settling, multiplexed, 8-/16-
Channel scan data rate of 50 kSPS/channel (20 µs settling)
Performance specifications
17.2 noise free bits at 250 kSPS
20.2 noise free bits at 2.5 kSPS
24 noise free bits at 20 SPS
INL: 1 ppm of FSR
85 dB filter rejection of 50 Hz and 60 Hz with 50 ms settling
User configurable input channels
8 fully differential channels or 16 single-ended channels
Crosspoint multiplexer
On-chip 2.5 V reference ( 2 ppm/°C drift)
True rail-to-rail analog and reference input buffers
Internal or external clock
channel (fully/pseudo differential) Σ-Δ analog-to-digital
converter (ADC) for low bandwidth inputs. It has a maximum
channel scan rate of 50 kSPS (20 µs) for fully settled data. The
output data rates range from 5 SPS to 250 kSPS.
The AD7175-8 integrates key analog and digital signal condition-
ing blocks to allow users to configure an individual setup for
each analog input channel in use. Each feature can be user selected
on a per channel basis. Integrated true rail-to-rail buffers on the
analog inputs and external reference inputs provide easy to drive
high impedance inputs. The precision 2.5 V low drift (2 ppm/°C)
band gap internal reference (with output reference buffer) adds
embedded functionality to reduce external component count.
The digital filter allows simultaneous 50 Hz and 60 Hz rejection
at a 27.27 SPS output data rate. The user can switch between
different filter options according to the demands of each channel
in the application. The ADC automatically switches through
each selected channel. Further digital processing functions
include offset and gain calibration registers, configurable on a
per channel basis.
Power supply: AVDD1 − AVSS = 5 V, AVDD2 = IOVDD = 2 V to
5 V (nominal)
Split supply with AVDD1/AVSS at 2.5 V
ADC current: 8.4 mA
Temperature range: −40°C to +105°C
3- or 4-wire serial digital interface (Schmitt trigger on SCLK)
Serial port interface (SPI), QSPI, MICROWIRE, and DSP
compatible
The device operates with a 5 V AVDD1 − AVSS supply, or with
2.5 V AVDD1/AVSS, and 2 V to 5 V AVDD2 and IOVDD
nominal supplies. The specified operating temperature range is
−40°C to +105°C. The AD7175-8 is available in a 40-lead LFCSP
package.
APPLICATIONS
Process control: PLC/DCS modules
Temperature and pressure measurement
Medical and scientific multichannel instrumentation
Chromatography
FUNCTIONAL BLOCK DIAGRAM
AVDD2 REGCAPA REF– REF+ REFOUT
AVDD1
IOVDD REGCAPD
CROSSPOINT
MULTIPLEXER
BUFFERED
PRECISION
REFERENCE
1.8V
LDO
1.8V
LDO
REFERENCE
INPUT
BUFFERS
AIN0/REF2–
AIN1/REF2+
AVDD
INT
REF
CS
SCLK
DIN
SERIAL
INTERFACE
AND CONTROL
DIGITAL
FILTER
Σ-Δ ADC
DOUT/RDY
SYNC
ERROR
AIN15
AIN16
ANALOG
INPUT
BUFFERS
AVSS
XTAL AND INTERNAL
CLOCK OSCILLATOR
CIRCUITRY
I/O AND EXTERNAL
MUX CONTROL
AD7175-8
TEMPERATURE
SENSOR
AVSS
PDSW
GPIO0GPIO1GPO2GPO3
XTAL1 XTAL2/CLKIO
DGND
Figure 1.
Rev. 0
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rightsof third parties that may result fromits use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks andregisteredtrademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Technical Support
©2015 Analog Devices, Inc. All rights reserved.
www.analog.com
AD7175-8* PRODUCT PAGE QUICK LINKS
Last Content Update: 02/23/2017
COMPARABLE PARTS
View a parametric search of comparable parts.
REFERENCE DESIGNS
• CN0292
EVALUATION KITS
• AD7175-8 Evaluation Board
DESIGN RESOURCES
• AD7175-8 Material Declaration
• PCN-PDN Information
DOCUMENTATION
Data Sheet
• Quality And Reliability
• Symbols and Footprints
• AD7175-8: 24-Bit, 8-/16-Channel, 250 kSPS, Sigma- Delta
ADC with True Rail-to-Rail Buffers Preliminary Data Sheet
DISCUSSIONS
View all AD7175-8 EngineerZone Discussions.
User Guides
• UG-901: Evaluating the AD7175-8 24-Bit, 250 kSPS, Sigma-
Delta ADC with 20 µs Settling and Integrated Analog
Input Buffers
SAMPLE AND BUY
Visit the product page to see pricing options.
SOFTWARE AND SYSTEMS REQUIREMENTS
• AD7175 Microcontroller Renesas Driver
• AD717x Microcontroller No-OS
TECHNICAL SUPPORT
Submit a technical question or find your regional support
number.
• AD717x Eval+ Software
DOCUMENT FEEDBACK
Submit feedback for this data sheet.
This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not
trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified.
AD7175-8
Data Sheet
TABLE OF CONTENTS
CRC Calculation......................................................................... 41
Integrated Functions ...................................................................... 43
General-Purpose I/O ................................................................. 43
External Multiplexer Control ................................................... 43
Delay ............................................................................................ 43
16-Bit/24-Bit Conversions......................................................... 43
DOUT_RESET ........................................................................... 43
Synchronization.......................................................................... 43
Error Flags................................................................................... 44
DATA_STAT ............................................................................... 44
IOSTRENGTH ........................................................................... 44
Power-Down Switch .................................................................. 45
Internal Temperature Sensor .................................................... 45
Grounding and Layout .................................................................. 46
Register Summary .......................................................................... 47
Register Details ............................................................................... 49
Communications Register......................................................... 49
Status Register............................................................................. 51
ADC Mode Register................................................................... 52
Interface Mode Register ............................................................ 53
Register Check............................................................................ 54
Data Register............................................................................... 54
GPIO Configuration Register................................................... 55
ID Register................................................................................... 56
Channel Register 0 ..................................................................... 56
Channel Register 1 to Channel Register 15 ............................ 58
Setup Configuration Register 0 ................................................ 59
Features .............................................................................................. 1
Applications....................................................................................... 1
General Description ......................................................................... 1
Functional Block Diagram .............................................................. 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Timing Characteristics ................................................................ 6
Absolute Maximum Ratings............................................................ 8
Thermal Resistance ...................................................................... 8
ESD Caution.................................................................................. 8
Pin Configuration and Function Descriptions............................. 9
Typical Performance Characteristics ........................................... 11
Noise Performance and Resolution.............................................. 17
Getting Started................................................................................ 18
Power Supplies ............................................................................ 19
Digital Communication............................................................. 19
AD7175-8 Reset.......................................................................... 20
Configuration Overview ........................................................... 20
Circuit Description......................................................................... 25
Buffered Analog Input ............................................................... 25
Crosspoint Multiplexer.............................................................. 25
AD7175-8 Reference.................................................................. 26
Buffered Reference Input........................................................... 27
Clock Source ............................................................................... 27
Digital Filters................................................................................... 28
Sinc5 + Sinc1 Filter..................................................................... 28
Sinc3 Filter................................................................................... 28
Single Cycle Settling................................................................... 29
Enhanced 50 Hz and 60 Hz Rejection Filters......................... 33
Operating Modes............................................................................ 36
Continuous Conversion Mode ................................................. 36
Continuous Read Mode............................................................. 37
Single Conversion Mode ........................................................... 38
Standby and Power-Down Modes............................................ 39
Calibration................................................................................... 39
Digital Interface .............................................................................. 40
Checksum Protection................................................................. 40
Setup Configuration Register 1 to Setup Configuration
Register 7 ..................................................................................... 60
Filter Configuration Register 0................................................. 61
Filter Configuration Register 1 to Filter Configuration
Register 7 ..................................................................................... 62
Offset Register 0 ......................................................................... 62
Offset Register 1 to Offset Register 7....................................... 62
Gain Register 0............................................................................ 62
Gain Register 1 to Gain Register 7........................................... 63
Outline Dimensions....................................................................... 64
Ordering Guide .......................................................................... 64
REVISION HISTORY
10/15—Revision 0: Initial Version
Rev. 0 | Page 2 of 64
Data Sheet
AD7175-8
SPECIFICATIONS
AVDD1 = 4.5 V to 5.5 V, AV DD2 = 2 V to 5.5 V, IOV DD = 2 V to 5.5 V, AVSS = DGND = 0 V, REF+ = 2.5 V, REF− = AVSS,
internal master clock (MCLK) = 16 MHz, TA = TMIN to TMAX (−40°C to +105°C), unless otherwise noted.
Table 1.
Parameter
Test Conditions/Comments
Min
Typ
Max
Unit
ADC SPEED AND PERFORMANCE
Output Data Rate (ODR)
No Missing Codes1
Resolution
5
24
250,000
SPS
Bits
Excluding sinc3 filter ≥ 125 kSPS
See Table 19 to Table 23
Noise
See Table 19 to Table 23
ACCURACY
Integral Nonlinearity (INL)
All input buffers enabled
All input buffers disabled
Internal short
4.5
1
60
150
80
0.5
10
4.5
ppm of FSR
ppm of FSR
µV
nV/°C
ppm of FSR
ppm/°C
Offset Error2
Offset Drift
Gain Error2
Gain Drift1
Internal short
110
0.75
REJECTION
Power Supply Rejection
Common-Mode Rejection
At DC
AVDD1, AVDD2, for VIN = 1 V
VIN = 0.1 V
90
dB
95
120
dB
dB
At 50 Hz, 60 Hz1
20 Hz output data rate (post filter), 50 Hz
1 Hz and 60 Hz 1 Hz
50 Hz 1 Hz and 60 Hz 1 Hz
Normal Mode Rejection1
Internal clock, 20 SPS ODR (postfilter)
External clock, 20 SPS ODR (postfilter)
71
85
90
90
dB
dB
ANALOG INPUTS
Differential Input Range
Absolute Voltage Limits1
Input Buffers Disabled
Input Buffers Enabled
Analog Input Current
Input Buffers Disabled
Input Current
VREF = (REF+) − (REF−)
VREF
V
AVSS − 0.05
AVSS
AVDD1 + 0.05
AVDD1
V
V
48
0.75
4
µA/V
nA/V/°C
nA/V/°C
Input Current Drift
External clock
Internal clock
Input Buffers Enabled
Input Current
Input Current Drift
30
75
1
nA
AVDD1 − 0.2 V to AVSS + 0.2 V
AVDD1 to AVSS
1 kHz input
pA/°C
nA/°C
dB
Crosstalk
−120
INTERNAL REFERENCE
Output Voltage
100 nF external capacitor to AVSS
REFOUT, with respect to AVSS
REFOUT, TA = 25°C
2.5
V
Initial Accuracy3
−0.12
−10
+0.12
% of V
Temperature Coefficient1
0°C to 105°C
2
3
5
10
+10
ppm/°C
ppm/°C
mA
−40°C to +105°C
Reference Load Current, ILOAD
Power Supply Rejection
Load Regulation
Voltage Noise
Voltage Noise Density
AVDD1, AVDD2 (line regulation)
∆VOUT/∆ILOAD
eN, 0.1 Hz to 10 Hz, 2.5 V reference
eN, 1 kHz, 2.5 V reference
95
32
4.5
215
dB
ppm/mA
µV rms
nV/√Hz
Rev. 0 | Page 3 of 64
AD7175-8
Data Sheet
Parameter
Test Conditions/Comments
Min
Typ
200
25
Max
Unit
µs
mA
Turn-On Settling Time
Short-Circuit Current, ISC
EXTERNAL REFERENCE INPUTS
Differential Input Range
Absolute Voltage Limits1
Input Buffers Disabled
Input Buffers Enabled
REF+/REF− Input Current
Input Buffers Disabled
Input Current
100 nF REFOUT capacitor
VREF = (REF+) − (REF−)
1
2.5
AVDD1
V
AVSS − 0.05
AVSS
AVDD1 + 0.05
AVDD1
V
V
72
1.2
6
µA/V
nA/V/°C
nA/V/°C
Input Current Drift
External clock
Internal clock
Input Buffers Enabled
Input Current
800
1.2
nA
nA/°C
Input Current Drift
Normal Mode Rejection1
Common-Mode Rejection
TEMPERATURE SENSOR
Accuracy
See the Rejection parameter
95
dB
After user calibration at 25°C
2
°C
Sensitivity
470
µV/K
BURNOUT CURRENTS
Source/Sink Current
POWER-DOWN SWITCH
RON
Analog input buffers must be enabled
10
24
µA
Ω
Allowable Currents
16
mA
GENERAL-PURPOSE INPUTS/OUTPUTS
(GPIO0, GPIO1, GPO2, GPO3)
Input Mode Leakage Current1
With respect to AVSS
−10
+10
µA
pF
V
V
V
Floating State Output Capacitance
5
1
Output High Voltage, VOH
ISOURCE = 200 µA
ISINK = 800 µA
AVSS + 4
AVSS + 3
1
Output Low Voltage, VOL
AVSS + 0.4
AVSS + 0.7
1
Input High Voltage, VINH
Input Low Voltage, VINL
1
V
CLOCK
Internal Clock
Frequency
Accuracy
16
50
MHz
%
%
V
V
−2.5%
+2.5%
0.4
Duty Cycle
Output Low Voltage, VOL
Output High Voltage, VOH
Crystal
0.8 × IOVDD
14
Frequency
16
10
16
50
16.384
MHz
µs
MHz
%
Start-Up Time
External Clock (CLKIO)
Duty Cycle1
16.384
70
30
Rev. 0 | Page 4 of 64
Data Sheet
AD7175-8
Parameter
Test Conditions/Comments
Min
Typ
Max
Unit
LOGIC INPUTS
Input High Voltage, VINH
1
2 V ≤ IOVDD < 2.3 V
0.65 ×
IOVDD
0.7 × IOVDD
V
V
V
V
V
V
µA
2.3 V ≤ IOVDD ≤ 5.5 V
2 V ≤ IOVDD < 2.3 V
2.3 V ≤ IOVDD ≤ 5.5 V
IOVDD ≥ 2.7 V
1
Input Low Voltage, VINL
0.35 × IOVDD
0.7
0.25
0.2
+10
Hysteresis1
0.08
0.04
−10
IOVDD < 2.7 V
Leakage Current
LOGIC OUTPUT (DOUT/RDY)
1
Output High Voltage, VOH
IOVDD ≥ 4.5 V, ISOURCE = 1 mA
2.7 V ≤ IOVDD < 4.5 V, ISOURCE = 500 µA
IOVDD < 2.7 V, ISOURCE = 200 µA
IOVDD ≥ 4.5 V, ISINK = 2 mA
2.7 V ≤ IOVDD < 4.5 V, ISINK = 1 mA
IOVDD < 2.7 V, ISINK = 400 µA
Floating state
0.8 × IOVDD
0.8 × IOVDD
0.8 × IOVDD
V
V
V
V
V
V
µA
pF
1
Output Low Voltage, VOL
0.4
0.4
0.4
+10
Leakage Current
Output Capacitance
SYSTEM CALIBRATION1
Full-Scale (FS) Calibration Limit
Zero-Scale Calibration Limit
Input Span
−10
Floating state
10
1.05 × FS
2.1 × FS
V
V
V
−1.05 × FS
0.8 × FS
POWER REQUIREMENTS
Power Supply Voltage
AVDD1 to AVSS
4.5
2
−2.75
2
5
5.5
5.5
0
5.5
6.35
V
V
V
V
V
AVDD2 to AVSS4
2.5 to 5
AVSS to DGND
IOVDD to DGND4
IOVDD to AVSS
2.5 to 5
For AVSS < DGND
POWER SUPPLY CURRENTS5
All outputs unloaded, digital inputs
connected to IOVDD or DGND
Full Operating Mode
AVDD1 Current
Analog input and reference input buffers
(AIN , REF ) disabled, external reference
Analog input and reference input buffers
disabled, internal reference
Analog input and reference input buffers
enabled, external reference
1.4
1.75
13
1.65
2
mA
mA
mA
16
Each buffer: AIN+, AIN−, REF+, REF−
External reference
Internal reference
External clock
Internal clock
External crystal
Internal reference off, total current
consumption
Internal reference on, total current
consumption
Full power-down (including LDO and
internal reference)
2.9
4.5
4.75
2.5
2.75
3
mA
mA
mA
mA
mA
mA
µA
AVDD2 Current
IOVDD Current
5
5.2
2.8
3.1
Standby Mode (LDO On)
Power-Down Mode
30
425
5
µA
µA
10
Rev. 0 | Page 5 of 64
AD7175-8
Data Sheet
Parameter
Test Conditions/Comments
Min
Typ
Max
Unit
POWER DISSIPATION5
Full Operating Mode
All buffers disabled, external clock and
reference, AVDD2 = 2 V, IOVDD = 2 V
All buffers disabled, external clock and
reference, all supplies = 5 V
All buffers disabled, external clock and
reference, all supplies = 5.5 V
All buffers enabled, internal clock and
reference, AVDD2 = 2 V, IOVDD = 2 V
All buffers enabled, internal clock and
reference, all supplies = 5 V
All buffers enabled, internal clock and
reference, all supplies = 5.5 V
Internal reference off, all supplies = 5 V
Internal reference on, all supplies = 5 V
Full power-down, all supplies = 5 V
21
42
mW
mW
mW
mW
mW
mW
52
82
105
136
50
Standby Mode
150
2.2
25
µW
mW
µW
Power-Down Mode
1 This specification is not production tested but is supported by characterization data at the initial product release.
2 Following a system or internal zero-scale calibration, the offset error is in the order of the noise for the programmed output data rate selected. A system full-scale
calibration reduces the gain error to the order of the noise for the programmed output data rate.
3 This specification includes moisture sensitivity level (MSL) preconditioning effects.
4 The nominal range is 2 V to 5 V.
5 This specification is with no load on the REFOUT and digital output pins.
TIMING CHARACTERISTICS
IOVDD = 2 V to 5.5 V, DGND = 0 V, Input Logic 0 = 0 V, Input Logic 1 = IOVDD, CLOAD = 20 pF, unless otherwise noted.
Table 2.
Parameter
Limit at TMIN, TMAX
Unit
Description1, 2
SCLK
t3
t4
25
25
ns min
ns min
SCLK high pulse width
SCLK low pulse width
READ OPERATION
t1
0
ns min
ns max
ns max
ns min
ns max
ns max
ns min
ns max
ns min
ns min
CS falling edge to DOUT/RDY active time
IOVDD = 4.75 V to 5.5 V
15
40
0
12.5
25
2.5
20
0
IOVDD = 2 V to 3.6 V
3
t2
SCLK active edge to data valid delay4
IOVDD = 4.75 V to 5.5 V
IOVDD = 2 V to 3.6 V
Bus relinquish time after CS inactive edge
5
t5
t6
t7
SCLK inactive edge to CS inactive edge
10
SCLK inactive edge to DOUT/RDY high/low
WRITE OPERATION
t8
0
8
8
5
ns min
ns min
ns min
ns min
CS falling edge to SCLK active edge setup time4
Data valid to SCLK edge setup time
Data valid to SCLK edge hold time
CS rising edge to SCLK edge hold time
t9
t10
t11
1 Sample tested during initial release to ensure compliance.
2 See Figure 2 and Figure 3.
3 This parameter is defined as the time required for the output to cross the VOL or VOH limits.
4 The SCLK active edge is the falling edge of SCLK.
5
RDY
while DOUT/
DOUT/
returns high after a read of the data register. In single conversion mode and continuous conversion mode, the same data can be read again, if required,
RDY
is high, although care must be taken to ensure that subsequent reads do not occur close to the next output update. If the continuous read feature is
enabled, the digital word can be read only once.
Rev. 0 | Page 6 of 64
Data Sheet
AD7175-8
Timing Diagrams
CS (I)
t6
t1
t5
MSB
LSB
DOUT/RDY (O)
t7
t2
t3
SCLK (I)
t4
I = INPUT, O = OUTPUT
Figure 2. Read Cycle Timing Diagram
CS (I)
t11
t8
SCLK (I)
DIN (I)
t9
t10
MSB
LSB
I = INPUT, O = OUTPUT
Figure 3. Write Cycle Timing Diagram
Rev. 0 | Page 7 of 64
AD7175-8
Data Sheet
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
THERMAL RESISTANCE
θJA is specified for a device soldered on a JEDEC test board for
surface-mount packages.
Table 3.
Parameter
Rating
AVDD1, AVDD2 to AVSS
AVDD1 to DGND
IOVDD to DGND
IOVDD to AVSS
−0.3 V to +6.5 V
−0.3 V to +6.5 V
−0.3 V to +6.5 V
−0.3 V to +7.5 V
−3.25 V to +0.3 V
−0.3 V to AVDD1 + 0.3 V
−0.3 V to AVDD1 + 0.3 V
−0.3 V to IOVDD + 0.3 V
−0.3 V to IOVDD + 0.3 V
10 mA
−40°C to +105°C
−65°C to +150°C
150°C
260°C
4 kV
Table 4. Thermal Resistance
Package Type
θJA
Unit
40-Lead, 6 mm × 6 mm LFCSP
1-Layer JEDEC Board
4-Layer JEDEC Board
114
54
34
°C/W
°C/W
°C/W
AVSS to DGND
Analog Input Voltage to AVSS
Reference Input Voltage to AVSS
Digital Input Voltage to DGND
Digital Output Voltage to DGND
Analog Input/Digital Input Current
Operating Temperature Range
Storage Temperature Range
Maximum Junction Temperature
Lead Soldering, Reflow Temperature
ESD Rating (Human Body Model)
4-Layer JEDEC Board with 16 Thermal Vias
ESD CAUTION
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
Rev. 0 | Page 8 of 64
Data Sheet
AD7175-8
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
AIN16
AIN0/REF2–
AIN1/REF2+
AIN2
1
2
3
4
5
6
7
8
9
30 AIN8
29 AIN7
28 AIN6
27 AIN5
AD7175-8
TOP VIEW
(Not to Scale)
AIN3
26 AIN4
REFOUT
REGCAPA
AVSS
AVDD1
AVDD2 10
25 GPO2
24 GPIO1
23 GPIO0
22 REGCAPD
21 DGND
NOTES
1. SOLDER THE EXPOSED PAD TO A SIMILAR PAD ON THE PCB UNDER THE
EXPOSED PAD TO CONFER MECHANICAL STRENGTH AND FOR HEAT
DISSIPATION. THE EXPOSED PAD MUST BE CONNECTED TO AVSS
THROUGH THIS PAD ON THE PCB.
Figure 4. Pin Configuration
Table 5. Pin Function Descriptions1
Pin No. Mnemonic
Type2 Description
1
2
AIN16
AIN0/REF2−
AI
AI
Analog Input 16. This pin is selectable through the crosspoint multiplexer.
Analog Input 0 (AIN0)/Reference 2, Negative Input (REF2−). An external reference can be applied
between REF2+ and REF2−. REF2− can span from AVSS to AVDD1 − 1 V. Analog Input 0 is selectable
through the crosspoint multiplexer. Reference 2 can be selected through the REF_SELx bits in the setup
configuration registers.
3
AIN1/REF2+
AI
Analog Input 1 (AIN0)/Reference 2, Positive Input (REF2+). An external reference can be applied between
REF2+ and REF2−. REF2+ spans from AVDD1 to AVSS + 1 V. Analog Input 1 is selectable through the
crosspoint multiplexer. Reference 2 can be selected through the REF_SELx bits in the setup
configuration registers.
4
5
6
7
8
9
AIN2
AIN3
REFOUT
REGCAPA
AVSS
AI
AI
AO
AO
P
Analog Input 2. This pin is selectable through the crosspoint multiplexer.
Analog Input 3. This pin is selectable through the crosspoint multiplexer.
Buffered Output of Internal Reference. The output is 2.5 V with respect to AVSS.
Analog Low Dropout (LDO) Regulator Output. Decouple this pin to AVSS using a 1 µF capacitor.
Negative Analog Supply. This supply ranges from 0 V to −2.75 V and is nominally set to 0 V.
Analog Supply Voltage 1. This voltage is 5 V 10% with respect to AVSS. AVDD1 − AVSS can be a single
5 V supply or a 2.5 V split supply.
AVDD1
P
10
11
12
13
AVDD2
PDSW
XTAL1
P
AO
AI
Analog Supply Voltage 2. This voltage ranges from 2 V to AVDD1 with respect to AVSS.
Power-Down Switch Connected to AVSS. This pin is controlled by the PDSW bit in the GPIOCON register.
Input 1 for Crystal.
Input 2 for Crystal (XTAL2)/Clock Input or Output (CLKIO). See the CLOCKSEL bit settings in the
ADCMODE register for more information.
XTAL2/CLKIO AI/DI
14
DOUT/RDY DO
Serial Data Output (DOUT)/Data Ready Output (RDY). This pin serves a dual purpose. It functions as a
serial data output pin to access the output shift register of the ADC. The output shift register can contain
data from any of the on-chip data or control registers. The data-word/control word information is placed
on the DOUT/RDY pin on the SCLK falling edge and is valid on the SCLK rising edge. When CS is high, the
DOUT/RDY output is tristated. When CS is low, and a register is not being read, DOUT/RDY operates as
a data ready pin, going low to indicate the completion of a conversion. If the data is not read after the
conversion, the pin goes high before the next update occurs. The DOUT/RDY falling edge can be used as
an interrupt to a processor, indicating that valid data is available.
Rev. 0 | Page 9 of 64
AD7175-8
Data Sheet
Pin No. Mnemonic
Type2 Description
15
DIN
DI
Serial Data Input to the Input Shift Register on the ADC. Data in this shift register is transferred to the
control registers in the ADC, with the register address (RA) bits of the communications register
identifying the appropriate register. Data is clocked in on the rising edge of SCLK.
16
17
SCLK
CS
DI
DI
Serial Clock Input. This serial clock input is for data transfers to and from the ADC. SCLK has a Schmitt
triggered input, making the interface suitable for opto-isolated applications.
Chip Select Input. This pin is an active low logic input used to select the ADC. Use CS to select the ADC in
systems with more than one device on the serial bus. CS can be hardwired low, allowing the ADC to operate
in 3-wire mode with SCLK, DIN, and DOUT/RDY used to interface with the device. When CS is high, the
DOUT/RDY output is tristated.
18
ERROR
DI/O
Error input/output or General-Purpose Output. This pin can be used in one of the following three modes:
Active low error input mode. This mode sets the ADC_ERROR bit in the STATUS register.
Active low, open-drain error output mode. The status register error bits are mapped to the ERROR pin.
The ERROR pins of multiple devices can be wired together to a common pull-up resistor so that an error
on any device can be observed.
General-purpose output mode. The status of the pin is controlled by the ERR_DAT bit in the GPIOCON register.
The pin is referenced between IOVDD and DGND, as opposed to the AVDD1 and AVSS levels used by the
GPIO1 and GPIO2 pins. The ERROR pin has an active pull-up circuit in this case.
19
20
SYNC
DI
P
Synchronization Input. Allows synchronization of the digital filters and analog modulators when using
multiple AD7175-8 devices.
Digital I/O Supply Voltage. The IOVDD voltage ranges from 2 V to 5 V (nominal). IOVDD is independent of
AVDD1 and AVDD2. For example, IOVDD can be operated at 3.3 V when AVDD1 or AVDD2 equals 5 V, or
vice versa. If AVSS is set to −2.5 V, the voltage on IOVDD must not exceed 3.6 V.
IOVDD
21
22
DGND
REGCAPD
P
AO
Digital Ground.
Digital LDO Regulator Output. This pin is for decoupling purposes only. Decouple this pin to DGND
using a 1 µF capacitor.
23
24
GPIO0
GPIO1
DI/O
DI/O
General-Purpose Input/Output 0. Logic input/output on this this pin is referred to the AVDD1 and AVSS
supplies.
General-Purpose Input/Output 2. Logic input/output on this this pin is referred to the AVDD1 and AVSS
supplies.
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
GPO2
AIN4
AIN5
AIN6
AIN7
DO
AI
AI
AI
AI
AI
AI
AI
AI
AI
AI
AI
AI
DO
AI
General-Purpose Output 2. Logic output on this this pin is referred to the AVDD1 and AVSS supplies.
Analog Input 4. This pin is selectable through the crosspoint multiplexer.
Analog Input 5. This pin is selectable through the crosspoint multiplexer.
Analog Input 6. This pin is selectable through the crosspoint multiplexer.
Analog Input 7. This pin is selectable through the crosspoint multiplexer.
Analog Input 8. This pin is selectable through the crosspoint multiplexer.
Analog Input 9. This pin is selectable through the crosspoint multiplexer.
Analog Input 10. This pin is selectable through the crosspoint multiplexer.
Analog Input 11. This pin is selectable through the crosspoint multiplexer.
Analog Input 12. This pin is selectable through the crosspoint multiplexer.
Analog Input 13. This pin is selectable through the crosspoint multiplexer.
Analog Input 14. This pin is selectable through the crosspoint multiplexer.
Analog Input 15. This pin is selectable through the crosspoint multiplexer.
General-Purpose Output 3. Logic output on this this pin is referred to the AVDD1 and AVSS supplies.
AIN8
AIN9
AIN10
AIN11
AIN12
AIN13
AIN14
AIN15
GPO3
REF−
Reference 1 Input Negative Terminal. REF− can span from AVSS to AVDD1 − 1 V. Reference 1 can be
selected through the REF_SELx bits in the setup configuration registers.
40
REF+
EP
AI
P
Reference 1 Input Positive Terminal. An external reference can be applied between REF+ and REF−. REF+
can span from AVDD1 to AVSS + 1 V. Reference 1 can be selected through the REF_SELx bits in the setup
configuration registers.
Exposed Pad. Solder the exposed pad to a similar pad on the PCB under the exposed pad to confer
mechanical strength to the package and for heat dissipation. The exposed pad must be connected to AVSS
through this pad on the PCB.
1 Note that, throughout this data sheet, the dual function pin names are referenced by the relevant function only.
2 AI = analog input, AO = analog output, P = power supply, DI = digital input, DO = digital output, and DI/O = bidirectional digital input/output.
Rev. 0 | Page 10 of 64
Data Sheet
AD7175-8
TYPICAL PERFORMANCE CHARACTERISTICS
AVDD1 = 5 V, AVDD2 = 5 V, IOVDD = 3.3 V, TA = 25°C, unless otherwise noted.
8390000
8389500
8389000
8388500
8388000
8387500
8387000
8386500
8386000
1000
900
800
700
600
500
400
300
200
100
0
0
100 200 300 400 500 600 700 800 900 1000
SAMPLE NUMBER
8388460 8388461 8388462 8388463 8388464 8388465 8388466
ADC CODE
Figure 5. Noise (Analog Input Buffers Disabled, VREF = 5 V,
Output Data Rate = 5 SPS)
Figure 8. Histogram (Analog Input Buffers Disabled, VREF = 5 V,
Output Data Rate = 5 SPS)
120
100
80
60
40
20
0
8388480
8388475
8388470
8388465
8388460
8388455
8388450
8388445
0
100 200 300 400 500 600 700 800 900 1000
SAMPLE NUMBER
ADC CODE
Figure 9. Histogram (Analog Input Buffers Disabled, VREF = 5 V,
Output Data Rate = 10 kSPS)
Figure 6. Noise (Analog Input Buffers Disabled, VREF = 5 V,
Output Data Rate = 10 kSPS)
45
40
35
30
25
20
15
10
5
8388520
8388500
8388480
8388460
8388440
8388420
8388400
0
0
100 200 300 400 500 600 700 800 900 1000
SAMPLE NUMBER
ADC CODE
Figure 10. Histogram (Analog Input Buffers Disabled, VREF = 5 V,
Output Data Rate = 250 kSPS)
Figure 7. Noise (Analog Input Buffers Disabled, VREF = 5 V,
Output Data Rate = 250 kSPS)
Rev. 0 | Page 11 of 64
AD7175-8
Data Sheet
1000
900
800
700
600
500
400
300
200
100
0
8390000
8389500
8389000
8388500
8388000
8387500
8387000
8386500
8386000
8385500
8385000
8388490 8388491 8388492 8388493 8388494 8388495 8388496
ADC CODE
0
100 200 300 400 500 600 700 800 900 1000
SAMPLE NUMBER
Figure 11. Noise (Analog Input Buffers Enabled, VREF = 5 V,
Output Data Rate = 5 SPS)
Figure 14. Histogram (Analog Input Buffers Enabled, VREF = 5 V,
Output Data Rate = 5 SPS)
8388520
100
90
80
70
60
50
40
30
20
10
0
8388515
8388510
8388505
8388500
8388495
8388490
8388485
8388480
0
100 200 300 400 500 600 700 800 900 1000
SAMPLE NUMBER
ADC CODE
Figure 12. Noise (Analog Input Buffers Enabled, VREF = 5 V,
Output Data Rate = 10 kSPS)
Figure 15. Histogram (Analog Input Buffers Enabled, VREF = 5 V,
Output Data Rate = 10 kSPS)
35
30
25
20
15
10
5
8388580
8388560
8388540
8388520
8388500
8388480
8388460
8388440
0
0
100 200 300 400 500 600 700 800 900 1000
SAMPLE NUMBER
ADC CODE
Figure 13. Noise (Analog Input Buffers Enabled, VREF = 5 V,
Output Data Rate = 250 kSPS)
Figure 16. Histogram (Analog Input Buffers Enabled, VREF = 5 V,
Output Data Rate = 250 kSPS)
Rev. 0 | Page 12 of 64
Data Sheet
AD7175-8
0
–20
0.000016
ANALOG INPUT BUFFERS ON
ANALOG INPUT BUFFERS OFF
0.000014
0.000012
0.000010
0.000008
0.000006
0.000004
0.000002
0
–40
–60
–80
–100
–120
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
1
10
100
1k
10k
100k
1M
INPUT COMMON-MODE VOLTAGE (V)
V
FREQUENCY (Hz)
IN
Figure 20. Common-Mode Rejection Ratio (CMRR) vs. VIN Frequency
(VIN = 0.1 V, Output Data Rate = 250 kSPS)
Figure 17. Noise vs. Input Common-Mode Voltage,
Analog Input Buffers On and Off
–80
–90
20
18
16
14
12
10
8
ANALOG INPUT BUFFERS OFF
ANALOG INPUT BUFFERS ON
–100
–110
–120
–130
–140
–150
–160
–170
–180
6
4
2
0
0
10
20
30
V
40
50
60
70
2
4
6
8
10
12
14
16
FREQUENCY (Hz)
FREQUENCY (MHz)
IN
Figure 18. Noise vs. External Master Clock Frequency,
Analog Input Buffers On and Off
Figure 21. Common-Mode Rejection Ratio (CMRR) vs. VIN Frequency
(VIN = 0.1 V, 10 Hz to 70 Hz, Output Data Rate = 20 SPS, Enhanced Filter)
16800000
–60
CONTINUOUS CONVERSION—REFERENCE DISABLED
STANDBY—REFERENCE DISABLED
STANDBY—REFERENCE ENABLED
AVDD1—EXTERNAL 2.5V REFERENCE
AVDD1—INTERNAL 2.5V REFERENCE
16780000
16760000
16740000
16720000
16700000
16680000
16660000
–70
–80
–90
–100
–110
–120
–130
1
10
100
1k
10k
1
10
100
1k
10k
100k
1M
10M
100M
SAMPLE NUMBER
V
FREQUENCY (Hz)
IN
Figure 19. Internal Reference Settling Time
Figure 22. Power Supply Rejection Ratio (PSRR) vs. VIN Frequency
Rev. 0 | Page 13 of 64
AD7175-8
Data Sheet
5
16
14
12
10
8
INT OSC BUFFERS OFF
INT OSC BUFFERS ON
EXT CRYSTAL BUFFERS OFF
EXT CRYSTAL BUFFERS ON
EXT CLK BUFFERS OFF
EXT CLK BUFFERS ON
4
3
2
1
0
–1
–2
–3
–4
–5
6
4
2
0
–2.5
–1.5
–0.5
0.5
1.5
2.5
V
(V)
INL ERROR (ppm)
IN
Figure 23. Integral Nonlinearity (INL) vs. VIN
(Differential Input, External 2.5 V Reference)
Figure 26. Integral Nonlinearity (INL) Distribution Histogram (All Input
Buffers Disabled, Differential Input, VREF = 5 V External, 92 Units)
6
4
50
45
40
35
30
25
20
15
10
5
INT OSC BUFFERS OFF
INT OSC BUFFERS ON
EXT CRYSTAL BUFFERS OFF
EXT CRYSTAL BUFFERS ON
EXT CLK BUFFERS OFF
EXT CLK BUFFERS ON
2
0
–2
–4
–6
0
–5
–4
–3
–2
–1
0
1
2
3
4
5
15.98 15.99 16.00 16.01 16.02 16.03 16.04 16.05
FREQUENCY (MHz)
V
(V)
IN
Figure 27. Internal Oscillator Frequency/Accuracy Distribution Histogram
(100 Units)
Figure 24. Integral Nonlinearity (INL) vs. VIN
(Differential Input, External 5 V Reference)
16400000
16300000
16200000
16100000
16000000
15900000
15800000
15700000
15600000
25
20
INT OSC BUFFERS OFF
INT OSC BUFFERS ON
EXT CRYSTAL BUFFERS OFF
EXT CRYSTAL BUFFERS ON
EXT CLK BUFFERS OFF
EXT CLK BUFFERS ON
15
10
5
0
–5
–10
–15
–20
–2.5
–1.5
–0.5
0.5
1.5
2.5
–40
–20
0
20
40
60
80
100
TEMPERATURE (°C)
V
(V)
IN
Figure 28. Internal Oscillator Frequency vs. Temperature
Figure 25. Integral Nonlinearity (INL) vs. VIN
(Differential Input, Internal 2.5 V Reference)
Rev. 0 | Page 14 of 64
Data Sheet
AD7175-8
1500
1000
500
160
140
120
100
80
DEVICE 1
DEVICE 2
DEVICE 3
0
60
–500
–1000
–1500
40
20
0
–60 –50 –40 –30 –20 –10
0
10 20 30 40 50 60 70 80 90 100 110 120
TEMPERATURE (°C)
GAIN ERROR (ppm of FSR)
Figure 29. Absolute Reference Error vs. Temperature
Figure 32. Gain Error Distribution Histogram
(All Input Buffers Enabled, 611 Units)
35
30
25
20
15
10
5
160
140
120
100
80
60
40
20
0
0
–74 –70 –66 –62 –58 –54 –50 –46 –42 –38 –34 –30
OFFSET ERROR (µV)
74 75 76 77 78 79 80 81 82 83 84 85
GAIN ERROR (ppm of FSR)
Figure 30. Offset Error Distribution Histogram (Internal Short, 92 Units)
Figure 33. Gain Error Distribution Histogram
(All Input Buffers Disabled, 647 Units)
14
12
10
8
20
18
16
14
12
10
8
6
6
4
4
2
2
0
0
OFFSET DRIFT (nV/°C)
GAIN ERROR DRIFT (ppm of FSR/°C)
Figure 34. Gain Error Drift Distribution Histogram
(All Input Buffers Enabled, 79 Units)
Figure 31. Offset Error Drift Distribution Histogram
(Internal Short, 92 Units)
Rev. 0 | Page 15 of 64
AD7175-8
Data Sheet
18
16
14
12
10
8
18
16
14
12
10
8
6
6
4
4
2
2
0
0
–1.2 –1.0 –0.8 –0.6 –0.4 –0.2
0
0.2 0.4 0.6 0.8 1.0
TEMPERATURE DELTA (°C)
GAIN ERROR DRIFT (ppm of FSR/°C)
Figure 35. Gain Error Drift over Temperature Distribution Histogram
(All Input Buffers Disabled, 79 Units)
Figure 38. Temperature Sensor Distribution Histogram
(Uncalibrated, 100 Units)
25
20
15
10
35
30
25
20
15
10
5
5
ALL INPUT BUFFERS OFF
ALL INPUT BUFFERS ON
0
0
–40
–20
0
20
40
60
80
100
9.60 9.65 9.70 9.75 9.80 9.85 9.90 9.95 10.00 10.05 10.10
CURRENT (µA)
TEMPERATURE (°C)
Figure 36. Supply Current vs. Temperature (Continuous Conversion Mode)
Figure 39. Burnout Current Distribution Histogram
(100 Units)
700
100
80
60
40
20
0
–40°C, AIN–
–40°C, AIN+
+25°C, AIN–
+25°C, AIN+
+85°C, AIN–
+85°C, AIN+
+105°C, AIN–
+105°C, AIN+
93 DEVICES
600
500
400
300
200
100
0
–5
–4
–3
–2
–1
0
1
2
3
4
5
–40
25
105
TEMPERATURE (°C)
INPUT VOLTAGE (V)
Figure 37. Supply Current vs. Temperature
(Standby Mode with Reference Enabled)
Figure 40. Analog Input Current vs. Input Voltage
(VCM = 2.5 V)
Rev. 0 | Page 16 of 64
Data Sheet
AD7175-8
NOISE PERFORMANCE AND RESOLUTION
Table 6 and Table 7 show the rms noise, peak-to-peak noise,
effective resolution, and the noise free (peak-to-peak)
resolution of the AD7175-8 for various output data rates and
filters. The numbers given are for the bipolar input range with
an external 5 V reference. These numbers are typical and are
generated with a differential input voltage of 0 V when the ADC
is continuously converting on a single channel. It is important
to note that the peak-to-peak resolution is calculated based on
the peak-to-peak noise. The peak-to-peak resolution represents
the resolution for which there is no code flicker.
Table 6. RMS Noise and Peak-to-Peak Resolution vs. Output Data Rate Using a Sinc5 + Sinc1 Filter (Default)1
Output Data Rate (SPS)
RMS Noise (µV rms)
Effective Resolution (Bits)
Peak-to-Peak Noise (µV p-p) Peak-to-Peak Resolution (Bits)
Input Buffers Disabled
250,000
62,500
10,000
1000
59.92
49.96
16.66
5
8.7
5.5
2.5
0.77
0.19
0.18
0.1
20.1
20.8
21.9
23.6
24
24
24
24
65
43
18.3
5.2
1.1
0.95
0.45
0.34
17.2
17.8
19.1
20.9
23.1
23.3
24
0.07
24
Input Buffers Enabled
250,000
62,500
10,000
1000
59.98
49.96
16.66
5
9.8
6.4
3
0.92
0.23
0.2
0.13
0.07
20
85
55
23
5.7
1.2
1
0.66
0.32
16.8
17.5
18.7
20.7
23.0
23.3
23.9
24
20.6
21.7
23.4
24
24
24
24
1 Selected rates only, 1000 samples.
Table 7. RMS Noise and Peak-to-Peak Resolution vs. Output Data Rate Using a Sinc3 Filter1
Output Data Rate (SPS)
RMS Noise (µV rms)
Effective Resolution (Bits)
Peak-to-Peak Noise (µV p-p) Peak-to-Peak Resolution (Bits)
Input Buffers Disabled
250,000
62,500
10,000
1000
60
50
16.66
5
210
5.2
1.8
0.56
0.13
0.13
0.07
0.05
15.5
20.9
22.4
24
24
24
1600
40
14
3.9
0.8
0.7
0.37
0.21
12.6
17.9
19.4
21.3
23.6
23.8
24
24
24
24
Input Buffers Enabled
250,000
62,500
10,000
1000
60
50
16.66
5
210
5.8
2.1
0.71
0.17
0.15
0.12
0.08
15.5
20.7
22.2
23.7
24
24
24
24
1600
48
16
4.5
1.1
0.83
0.6
0.35
12.6
17.7
19.3
21.1
23.1
23.5
24
24
1 Selected rates only, 1000 samples.
Rev. 0 | Page 17 of 64
AD7175-8
Data Sheet
GETTING STARTED
The AD7175-8 offers the user a fast settling, high resolution,
multiplexed ADC with high levels of configurability. The
AD7175-8 includes the following features:
The AD7175-8 includes a precision 2.5 V low drift ( 2 ppm/°C)
band gap internal reference. This reference can used for the
ADC conversions, reducing the external component count.
Alternatively, the reference can be output to the REFOUT pin to
be used as a low noise biasing voltage for external circuitry. An
example of this is using the REFOUT signal to set the input
common mode for an external amplifier.
•
•
Eight fully differential or 16 single-ended analog inputs.
A crosspoint multiplexer selects any analog input
combination as the input signals to be converted, routing it
to the modulator positive or negative input.
The AD7175-8 includes two separate linear regulator blocks for
both the analog and digital circuitry. The analog LDO regulates
the AVDD2 supply to 1.8 V, supplying the ADC core. The user
can tie the AVDD1 and AVDD2 supplies together for the easiest
connection. If there is already a clean analog supply rail in the
system in the range of 2 V (minimum) to 5.5 V (maximum), the
user can also choose to connect this to the AVDD2 input,
allowing lower power dissipation.
•
•
True rail-to-rail buffered analog and reference inputs.
Fully differential input or single-ended input relative to any
analog input.
Per channel configurability—up to eight different setups
can be defined. A separate setup can be mapped to each of
the channels. Each setup allows the user to configure
whether the buffers are enabled or disabled, gain and offset
correction, filter type, output data rate, and reference
source selection (internal/external).
•
16MHz
CX2
CX1
SEE THE BUFFERED ANALOG INPUT SECTION
FOR FURTHER DETAILS
OPTIONAL EXTERNAL
CRYSTAL CIRCUITRY
CAPACITORS
12
XTAL1
2
AIN0/REF2–
XTAL2/CLKIO 13
DOUT/RDY 14
CLKIN
OPTIONAL
EXTERNAL
CLOCK
DOUT/RDY
DIN
3
AIN1/REF2+
AIN14
INPUT
15
DIN
16
SCLK
CS
SCLK
36
17
CS
37
1
AIN15
AIN16
AD7175-8
IOVDD
0.1µF
20
21
IOVDD
DGND
REGCAPD 22
1
3
0.1µF
1µF
AVDD1
V
IN
TP
NC
AVDD1
AVDD2
9
10
7
2
4
7
6
V
NC
IN
0.1µF
4.7µF
0.1µF
AVDD2
ADR445
40
39
GND
V
REF+
REF–
OUT
0.1µF
0.1µF
4.7µF
0.1µF
TRIM
5
TP
8
REGCAPA
0.1µF
1µF
AVSS
8
Figure 41. Typical Connection Diagram
Rev. 0 | Page 18 of 64
Data Sheet
AD7175-8
The linear regulator for the digital IOVDD supply performs a
similar function, regulating the input voltage applied at the
IOVDD pin to 1.8 V for the internal digital filtering. The serial
interface signals always operate from the IOVDD supply seen at
the pin. This means that if 3.3 V is applied to the IOVDD pin,
the interface logic inputs and outputs operate at this level.
DRIVE EDGE
SAMPLE EDGE
Figure 42. SPI Mode 3 SCLK Edges
The AD7175-8 can be used across a wide variety of applications,
providing high resolution and accuracy. A sample of these
scenarios is as follows:
Accessing the ADC Register Map
The communications register controls access to the full register
map of the ADC. This register is an 8-bit write only register. On
power-up or after a reset, the digital interface defaults to a state
where it is expecting a write to the communications register;
therefore, all communication begins by writing to the
communications register.
Fast scanning of analog input channels using the internal
multiplexer
Fast scanning of analog input channels using an external
multiplexer with automatic control from the GPIOs.
High resolution at lower speeds in either channel scanning
or ADC per channel applications
The data written to the communications register determines
which register is being accessed and if the next operation is a
read or write. The register address bits (RA[5:0]) determine the
specific register to which the read or write operation applies.
High resolution applications requiring a highly integrated
solution to save printed circuit board (PCB) area
POWER SUPPLIES
When the read or write operation to the selected register is
complete, the interface returns to its default state, where it
expects a write operation to the communications register.
The AD7175-8 has three independent power supplies: AVDD1,
AVDD2, and IOVDD.
AVDD1 powers the crosspoint multiplexer and integrated analog
and reference input buffers. AVDD1 is referenced to AVSS, and
AVDD1 − AVSS = 5 V only. AVDD1 − AVSS can be a single 5 V
supply or a 2.5 V split supply. The split supply operation allows
true bipolar inputs. When using split supplies, consider the absolute
maximum ratings (see the Absolute Maximum Ratings section).
Figure 43 and Figure 44 illustrate writing to and reading from a
register by first writing the 8-bit command to the communications
register, followed by the data for that register.
8 BITS, 16 BITS,
8-BIT COMMAND
OR 24 BITS OF DATA
CS
AVDD2 powers the internal 1.8 V analog LDO regulator. This
regulator powers the ADC core. AVDD2 is referenced to AVSS,
and AVDD2 − AVSS can range from 2 V (minimum) to 5.5 V
(maximum).
CMD
DATA
DIN
IOVDD powers the internal 1.8 V digital LDO regulator. This
regulator powers the digital logic of the ADC. IOVDD sets the
voltage levels for the SPI interface of the ADC. IOVDD is refer-
enced to DGND, and IOVDD − DGND can vary from 2 V
(minimum) to 5.5 V (maximum).
SCLK
Figure 43. Writing to a Register
(8-Bit Command with Register Address Followed by Data of 8, 16, or 24 Bits;
Data Length on DIN Is Dependent on the Register Selected)
There is no specific requirement for a power supply sequence
on the AD7175-8. When all power supplies are stable, a device
reset is required; see the AD7175-8 Reset section for details on
how to reset the device.
8 BITS, 16 BITS,
24 BITS, OR
32 BITS OUTPUT
8-BIT COMMAND
CS
DIGITAL COMMUNICATION
CMD
DIN
The AD7175-8 has a 3- or 4-wire SPI interface that is compatible
with QSPI™, MICROWIRE®, and DSPs. The interface operates
CS
in SPI Mode 3 and can be operated with
tied low. In SPI
DOUT/RDY
DATA
Mode 3, SCLK idles high, the falling edge of SCLK is the drive
edge, and the rising edge of SCLK is the sample edge. This
means that data is clocked out on the falling/drive edge and data
is clocked in on the rising/sample edge.
SCLK
Figure 44. Reading from a Register
(8-Bit Command with Register Address Followed by Data of 8, 16, or 24 Bits;
Data Length on DOUT Is Dependent on the Register Selected)
Rev. 0 | Page 19 of 64
AD7175-8
Data Sheet
Reading the ID register is the recommended method for verifying
correct communication with the device. The ID register is a
read only register and contains the value 0x3CDx for the
AD7175-8. The communications register and the ID register
details are described in Table 8 and Table 9, respectively.
Figure 45 shows an overview of the suggested flow for changing
the ADC configuration, divided into the following three blocks:
•
•
•
Channel configuration (see Box A in Figure 45)
Setup configuration (see Box B in Figure 45)
ADC mode and interface mode configuration (see Box C
in Figure 45)
AD7175-8 RESET
In situations where interface synchronization is lost, a write
operation of at least 64 serial clock cycles with DIN high returns the
ADC to its default state by resetting the entire device, including
Channel Configuration
The AD7175-8 has 16 independent channels and 8 independent
setups. The user can select any of the analog input pairs on any
channel, as well as any of the eight setups for any channel, giving
the user full flexibility in the channel configuration. This also
allows per channel configuration for up to eight channels when
using differential inputs or single-ended inputs. Channel configura-
tion can be shared across multiple channels.
CS
the register contents. Alternatively, if
is being used with the
CS
digital interface, returning
high sets the digital interface to its
default state and halts any serial interface operation.
CONFIGURATION OVERVIEW
After power-on or reset, the AD7175-8 default configuration
are as follows. Note that only a few of the register setting
options are shown; this list is just an example. For full register
information, see the Register Details section.
Channel Registers
The channel registers are used to select which of the 17 analog
input pins (AIN0 to AIN16) are used as either the positive analog
input (AIN+) or the negative analog input (AIN−) for that
channel. This register also contains a channel enable/disable bit
and the setup selection bits, which are used to select from the
eight available setups for this channel.
•
Channel configuration. CH0 is enabled, AIN0 is selected
as the positive input, and AIN1 is selected as the negative
input. Setup 0 is selected.
•
Setup configuration. The internal reference and the analog
input buffers are enabled. The reference input buffers are
disabled.
When the AD7175-8 is operating with more than one channel
enabled, the channel sequencer cycles through the enabled
channels in sequential order, from Channel 0 to Channel 15. If a
channel is disabled, it is skipped by the sequencer. Details of the
channel register for Channel 0 are shown in Table 10.
•
•
•
Filter configuration. The sinc5 + sinc 1 filter is selected and
the maximum output data rate is selected.
ADC mode. Continuous conversion mode and the internal
oscillator are enabled.
Interface mode. CRC and the data + status output are disabled.
A
B
C
CHANNEL CONFIGURATION
SELECT POSITIVE AND NEGATIVE INPUT FOR EACH ADC CHANNEL
SELECT ONE OF 8 SETUPS FOR ADC CHANNEL
SETUP CONFIGURATION
8 POSSIBLE ADC SETUPS
SELECT FILTER ORDER, OUTPUT DATA RATE, AND MORE
ADC MODE AND INTERFACE MODE CONFIGURATION
SELECT ADC OPERATING MODE, CLOCK SOURCE,
ENABLE CRC, DATA + STATUS, AND MORE
Figure 45. Suggested ADC Configuration Flow
Table 8. Communications Register
Reg.
Name
Bits
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 1
Bit 0
Bit 0
Reset
RW
0x00
COMMS
[7:0]
WEN
W
RA
0x00
W
R/
Table 9. ID Register
Reg.
Name
Bits
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Reset
RW
0x07
ID
[15:8]
[7:0]
ID[15:8]
ID[7:0]
0x3CDx
R
Table 10. Channel 0 Register
Reg.
Name
Bits
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
RW
0x10
CH0
[15:8]
[7:0]
CH_EN0
Reserved
AINPOS0[2:0]
SETUP_SEL[2:0]
Reserved
AINNEG0
AINPOS0[4:3]
0x8001
RW
Rev. 0 | Page 20 of 64
Data Sheet
AD7175-8
Setup Configuration Registers
ADC Setups
The setup configuration registers allow the user to select the
output coding of the ADC by selecting between bipolar mode
and unipolar mode. In bipolar mode, the ADC accepts negative
differential input voltages, and the output coding is offset binary.
In unipolar mode, the ADC accepts only positive differential
voltages, and the coding is straight binary. In either case, the
input voltage must be within the AVDD1/ AVSS supply voltages.
The user can select the reference source using these registers.
Three options are available: an internal 2.5 V reference, an
external reference connected between the REF+ and REF− pins,
or AVDD1 − AVSS. The analog input and reference input
buffers can also be enabled or disabled using this register.
The AD7175-8 has eight independent setups. Each setup
consists of the following four registers:
Setup configuration register
Filter configuration register
Gain register
Offset register
For example, Setup 0 consists of Setup Configuration Register 0,
Filter Configuration Register 0, Gain Register 0, and Offset
Register 0. Figure 46 shows the grouping of these registers. The
setup is selectable from the channel registers (see the Channel
Configuration section), which allows each channel to be assigned
to one of eight separate setups. Table 11 through Table 14 show the
four registers associated with Setup 0. This structure is repeated
for Setup 1 to Setup 3.
Filter Configuration Registers
The filter configuration registers select which digital filter is
used at the output of the ADC modulator. The order of the filter
and the output data rate is selected by setting the bits in this
register. For more information, see the Digital Filters section.
SETUP CONFIG
REGISTERS
FILTER CONFIG
REGISTERS
GAIN REGISTERS*
OFFSET REGISTERS
SETUPCON0
SETUPCON1
SETUPCON2
SETUPCON3
SETUPCON4
SETUPCON5
SETUPCON6
SETUPCON7
FILTCON0
FILTCON1
FILTCON2
FILTCON3
FILTCON4
FILTCON5
FILTCON6
FILTCON7
GAIN0
GAIN1
GAIN2
GAIN3
GAIN4
GAIN5
GAIN6
GAIN7
OFFSET0
0x30
0x20
0x21
0x22
0x23
0x24
0x25
0x26
0x27
0x28
0x29
0x2A
0x2B
0x2C
0x2D
0x2E
0x2F
0x38
0x39
0x3A
0x3B
0x3C
0x3D
0x3E
0x3F
OFFSET1
0x31
OFFSET2
0x32
OFFSET3
0x33
OFFSET4
0x34
OFFSET5
0x35
OFFSET6
0x36
OFFSET7
0x37
SELECT PERIPHERAL
FUNCTIONS FOR
ADC CHANNEL
SELECT DIGITAL
FILTER TYPE
GAIN CORRECTION
OPTIONALLY
OFFSET CORRECTION
OPTIONALLY PROGRAMMED
PER SETUP AS REQUIRED
AND OUTPUT DATA RATE
PROGRAMMED
PER SETUP AS REQUIRED
(*FACTORY CALIBRATED)
INPUT BUFFERS
REFERENCE BUFFERS
BURNOUT
SINC5 + SINC1
SINC3
SINC3 MAP
REFERENCE SOURCE
ENHANCED 50Hz AND 60Hz
Figure 46. ADC Setup Register Grouping
Table 11. Setup Configuration 0 Register
Reg. Name
Bits
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
RW
0x20 SETUPCON0 [15:8]
Reserved
BI_UNIPOLAR0
REFBUF0− AINBUF0+ AINBUF0− 0x1320
Reserved
RW
REFBUF0+
[7:0] BURNOUT_EN0 Reserved
REF_SEL0
Table 12. Filter Configuration 0 Register
Reg. Name
Bits
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
ENHFILT0
Bit 0
Reset
RW
0x28 FILTCON0 [15:8] SINC3_MAP0
[7:0] Reserved
Reserved
ORDER0
ENHFILTEN0
0x0500
RW
ODR0
Table 13. Gain Configuration 0 Register
Reg. Name
Bits
Bit[23:0]
Reset
RW
0x38 GAIN0
[23:0]
GAIN0[23:0]
0x5XXXX0 RW
Table 14. Offset Configuration 0 Register
Reg. Name
Bits
Bit[23:0]
Reset
RW
0x30 OFFSET0
[23:0]
OFFSET0[23:0]
0x800000 RW
Rev. 0 | Page 21 of 64
AD7175-8
Data Sheet
ADC Mode and Interface Mode Configuration
Gain Registers
The ADC mode register and the interface mode register configure
the core peripherals for use by the AD7175-8 and the mode for
the digital interface.
The gain registers are 24-bit registers that hold the gain
calibration coefficient for the ADC. The gain registers are
read/write registers. These registers are configured at power-on
with factory calibrated coefficients. Therefore, every device has
different default coefficients. The default value is automatically
overwritten if a system full-scale calibration is initiated by the
user or if the gain register is written to by the user. For more
information on calibration, see the Operating Modes section.
ADC Mode Register
The ADC mode register primarily sets the conversion mode of
the ADC to either continuous or single conversion. The user
can also select the standby and power-down modes, as well as
any of the calibration modes. In addition, this register contains
the clock source select bits and the internal reference enable
bits. The reference select bits are contained in the setup
configuration registers (see the ADC Setups section for more
information).
Offset Registers
The offset registers hold the offset calibration coefficient for the
ADC. The power-on reset value of the offset registers is 0x800000.
The offset registers are 24-bit read/write registers. The power-
on reset value is automatically overwritten if an internal or
system zero-scale calibration is initiated by the user or if the offset
registers are written to by the user.
Interface Mode Register
The interface mode register configures the digital interface
operation. This register allows the user to control data-word
length, CRC enable, data + status read, and continuous read mode.
The details of the ADC mode and interface mode registers are
shown in Table 15 and Table 16, respectively. For more information,
see the Digital Interface section.
Table 15. ADC Mode Register
Reg. Name
0x01 ADCMODE [15:8] REF_EN
[7:0] Reserved
Bits
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Reserved
Bit 2
CLOCKSEL
Bit 1
Delay
Reserved
Bit 0
Reset
RW
HIDE_DELAY SING_CYC
Mode
0xA000 RW
Table 16. Interface Mode Register
Reg.
Name
Bits
Bit 7
Bit 6
Reserved
CONTREAD DATA_STAT
Bit 5
Bit 4
ALT_SYNC IOSTRENGTH
Reserved CRC_EN
Bit 3
Bit 2
Bit 1
Reserved
Reserved
Bit 0
Reset
RW
0x02 IFMODE [15:8]
[7:0]
DOUT_RESET
WL16
0x0000 RW
REG_CHECK
Rev. 0 | Page 22 of 64
Data Sheet
AD7175-8
Understanding Configuration Flexibility
Programming the gain and offset registers is optional for any
use case, as indicated by the dashed lines between the register
blocks.
The most straightforward implementation of the AD7175-8 is
to use eight differential inputs with adjacent analog inputs and
run all of them with the same setup, gain correction, and offset
correction register. In this case, the user selects the following
differential inputs: AIN0/AIN1, AIN2/AIN3, AIN4/AIN5,
AIN6/AIN7, AIN8/AIN9, AIN10/AIN11, AIN12/AIN13, and
AIN14/AIN15. In Figure 47, the registers shown in black font
must be programmed for such a configuration. The registers
shown in gray font are redundant in this configuration.
An alternative way to implement these eight fully differential
inputs is by taking advantage of the eight available setups.
Motivation for doing this includes having a different speed/noise
requirement on some of the eight differential inputs vs. other
inputs, or there may be a specific offset or gain correction for
particular channels. Figure 48 shows how each of the differential
inputs may use a separate setup, allowing full flexibility in the
configuration of each channel.
CHANNEL
REGISTERS
AIN0
AIN1
CH0
CH1
0x10
0x11
0x12
0x13
0x14
0x15
0x16
0x17
0x18
0x19
0x1A
0x1B
0x1C
0x1D
0x1E
0x1F
AIN2
CH2
AIN3
CH3
SETUP CONFIG
REGISTERS
FILTER CONFIG
REGISTERS
GAIN REGISTERS*
OFFSET REGISTERS
AIN4
CH4
SETUPCON0
FILTCON0
GAIN0
OFFSET0
0x30
0x20
0x21
0x22
0x23
0x24
0x25
0x26
0x27
0x28
0x29
0x2A
0x2B
0x2C
0x2D
0x2E
0x2F
0x38
0x39
0x3A
0x3B
0x3C
0x3D
0x3E
0x3F
AIN5
CH5
SETUPCON1
SETUPCON2
SETUPCON3
SETUPCON4
SETUPCON5
SETUPCON6
SETUPCON7
FILTCON1
FILTCON2
FILTCON3
FILTCON4
FILTCON5
FILTCON6
FILTCON7
GAIN1
GAIN2
GAIN3
GAIN4
GAIN5
GAIN6
GAIN7
OFFSET1
0x31
AIN6
CH6
OFFSET2
0x32
AIN7
CH7
OFFSET3
0x33
AIN8
CH8
OFFSET4
0x34
AIN9
CH9
OFFSET5
0x35
AIN10
AIN11
AIN12
AIN13
AIN14
AIN15
AIN16
CH10
CH11
CH12
CH13
CH14
CH15
OFFSET6
0x36
OFFSET7
0x37
SELECT PERIPHERAL
FUNCTIONS FOR
ADC CHANNEL
SELECT DIGITAL
FILTER TYPE
GAIN CORRECTION
OPTIONALLY
OFFSET CORRECTION
OPTIONALLY PROGRAMMED
PER SETUP AS REQUIRED
AND OUTPUT DATA RATE
PROGRAMMED
PER SETUP AS REQUIRED
(*FACTORY CALIBRATED)
INPUT BUFFERS
REFERENCE BUFFERS
BURNOUT
250kSPS TO 5SPS
SINC5 + SINC1
SINC3
SELECT ANALOG INPUT PAIRS
ENABLE THE CHANNEL
SELECT SETUP 0
REFERENCE SOURCE
SINC3 MAP
ENHANCED 50Hz AND 60Hz
Figure 47. Eight Fully Differential Inputs, All Using a Single Setup (SETUPCON0; FILTCON0; GAIN0; OFFSET0)
CHANNEL
REGISTERS
AIN0
AIN1
CH0
CH1
0x10
0x11
0x12
0x13
0x14
0x15
0x16
0x17
0x18
0x19
0x1A
0x1B
0x1C
0x1D
0x1E
AIN2
CH2
AIN3
CH3
SETUP CONFIG
REGISTERS
FILTER CONFIG
REGISTERS
GAIN REGISTERS*
OFFSET REGISTERS
AIN4
CH4
SETUPCON0
FILTCON0
GAIN0
OFFSET0
0x30
0x20
0x21
0x22
0x23
0x24
0x25
0x26
0x27
0x28
0x29
0x2A
0x2B
0x2C
0x2D
0x2E
0x2F
0x38
0x39
0x3A
0x3B
0x3C
0x3D
0x3E
0x3F
AIN5
CH5
SETUPCON1
SETUPCON2
SETUPCON3
SETUPCON4
SETUPCON5
SETUPCON6
SETUPCON7
FILTCON1
FILTCON2
FILTCON3
FILTCON4
FILTCON5
FILTCON6
FILTCON7
GAIN1
GAIN2
GAIN3
GAIN4
GAIN5
GAIN6
GAIN7
OFFSET1
0x31
AIN6
CH6
OFFSET2
0x32
AIN7
CH7
OFFSET3
0x33
AIN8
CH8
OFFSET4
0x34
AIN9
CH9
OFFSET5
0x35
AIN10
AIN11
AIN12
AIN13
AIN14
AIN15
AIN16
CH10
CH11
CH12
CH13
CH14
CH15
OFFSET6
0x36
OFFSET7
0x37
SELECT PERIPHERAL
FUNCTIONS FOR
ADC CHANNEL
SELECT DIGITAL
FILTER TYPE
GAIN CORRECTION
OPTIONALLY
OFFSET CORRECTION
OPTIONALLY PROGRAMMED
PER SETUP AS REQUIRED
AND OUTPUT DATA RATE
PROGRAMMED
PER SETUP AS REQUIRED
(*FACTORY CALIBRATED)
INPUT BUFFERS
REFERENCE BUFFERS
BURNOUT
250kSPS TO 5SPS
SINC5 + SINC1
SINC3
0x1F
SELECT ANALOG INPUT PAIRS
ENABLE THE CHANNEL
SELECT SETUP
REFERENCE SOURCE
SINC3 MAP
ENHANCED 50Hz AND 60Hz
Figure 48. Eight Fully Differential Inputs with a Setup per Channel
Rev. 0 | Page 23 of 64
AD7175-8
Data Sheet
programmed as required, and the FILTCON0, FILTCON1, and
FILTCON2 registers are also programmed as required. Optional
gain and offset correction can be employed on a per setup basis
by programming the GAIN0, GAIN1, and GAIN2 registers and
the OFFSET0, OFFSET1, and OFFSET2 registers.
Figure 49 shows an example of how the channel registers span
between the analog input pins and the setup configurations
downstream. In this random example, seven differential inputs
and two single-ended inputs are required. The single-ended
inputs are the AIN8/AIN16 and AIN15/AIN16 combinations.
The first five differential input pairs (AIN0/AIN1, AIN2/AIN3,
AIN4/AIN5, AIN6/AIN7, and AIN9/AIN10) use the same setup:
SETUPCON0. The two single-ended input pairs (AIN8/AIN16
and AIN15/ AIN16) are set up as a diagnostics; therefore, use a
separate setup: SETUPCON1. The final two differential inputs
(AIN11/AIN12 and AIN13/AIN14) also use a separate setup:
SETUPCON2. Given that three setups are selected for use, the
SETUPCON0, SETUPCON1, and SETUPCON2 registers are
In the example shown in Figure 49, the CH0 to CH8 registers
are used. Setting the MSB in each of these registers, the CH_EN0
to CH_EN8 bits, enables the nine combinations via the crosspoint
multiplexer. When the AD7175-8 converts, the sequencer
transitions in ascending sequential order from CH0 to CH1 to
CH2, and then on to CH8 before looping back to CH0 to repeat
the sequence.
CHANNEL
REGISTERS
AIN0
AIN1
CH0
CH1
0x10
0x11
0x12
0x13
0x14
0x15
0x16
0x17
0x18
0x19
0x1A
0x1B
0x1C
0x1D
0x1E
AIN2
CH2
AIN3
CH3
SETUP CONFIG
REGISTERS
FILTER CONFIG
REGISTERS
GAIN REGISTERS*
OFFSET REGISTERS
AIN4
CH4
SETUPCON0
FILTCON0
GAIN0
OFFSET0
0x30
0x20
0x21
0x22
0x23
0x24
0x25
0x26
0x27
0x28
0x29
0x2A
0x2B
0x2C
0x2D
0x2E
0x2F
0x38
0x39
0x3A
0x3B
0x3C
0x3D
0x3E
0x3F
AIN5
CH5
SETUPCON1
SETUPCON2
SETUPCON3
SETUPCON4
SETUPCON5
SETUPCON6
SETUPCON7
FILTCON1
FILTCON2
FILTCON3
FILTCON4
FILTCON5
FILTCON6
FILTCON7
GAIN1
GAIN2
GAIN3
GAIN4
GAIN5
GAIN6
GAIN7
OFFSET1
0x31
AIN6
CH6
OFFSET2
0x32
AIN7
CH7
OFFSET3
0x33
AIN8
CH8
OFFSET4
0x34
AIN9
CH9
OFFSET5
0x35
AIN10
AIN11
AIN12
AIN13
AIN14
AIN15
AIN16
CH10
CH11
CH12
CH13
CH14
CH15
OFFSET6
0x36
OFFSET7
0x37
SELECT PERIPHERAL
FUNCTIONS FOR
ADC CHANNEL
SELECT DIGITAL
FILTER TYPE
GAIN CORRECTION
OPTIONALLY
OFFSET CORRECTION
OPTIONALLY PROGRAMMED
PER SETUP AS REQUIRED
AND OUTPUT DATA RATE
PROGRAMMED
PER SETUP AS REQUIRED
(*FACTORY CALIBRATED)
INPUT BUFFERS
REFERENCE BUFFERS
BURNOUT
250kSPS TO 5SPS
SINC5 + SINC1
SINC3
0x1F
SELECT ANALOG INPUT PAIRS
ENABLE THE CHANNEL
SELECT SETUP
REFERENCE SOURCE
SINC3 MAP
ENHANCED 50Hz AND 60Hz
Figure 49. Mixed Differential and Single-Ended Configuration Using Multiple Shared Setups
Rev. 0 | Page 24 of 64
Data Sheet
AD7175-8
CIRCUIT DESCRIPTION
AVDD1
AVSS
BUFFERED ANALOG INPUT
AIN0
AIN1
The AD7175-8 has true rail-to-rail, integrated, precision unity-
gain buffers on both ADC analog inputs. The buffers provide
the benefit of giving the user high input impedance with only
30 nA typical input current, allowing high impedance sources
to be connected directly to the analog inputs. The buffers fully
drive the internal ADC switch capacitor sampling network,
simplifying the analog front-end circuit requirements while
consuming a very efficient 2.9 mA typical per buffer. Each analog
input buffer amplifier is fully chopped, meaning that it minimizes
the offset error drift and 1/f noise of the buffer. The 1/f noise
profile of the ADC and buffer combined is shown in Figure 50.
0
AVDD1
Ø1
+IN
CS1
AVSS
Ø2
Ø2
AVDD1
AVSS
CS2
AIN14
Ø1
–IN
AVDD1
AIN15
AIN16
–50
–100
–150
–200
–250
AVSS
AVDD1
AVSS
Figure 51. Simplified Analog Input Circuit
The CS1 and CS2 capacitors each have a magnitude in the order
of a number of picofarads. This capacitance is the combination
of both the sampling capacitance and the parasitic capacitance.
0.1
1
10
100
1k
10k
Fully Differential Inputs
FREQUENCY (Hz)
Because the AIN0 to AIN16 analog inputs are connected to a
crosspoint multiplexer, any combination of signals can be used
to create an analog input pair. This crosspoint multiplexer allows
the user to select eight fully differential inputs or 16 single-ended
inputs.
Figure 50. Shorted Input FFT (Analog Input Buffers Enabled)
The analog input buffers do not suffer from linearity
degradation when operating at the rails, unlike many discrete
amplifiers. When operating at or close to the AVDD1 and AVSS
supply rails, there is an increase in input current. This increase
is most notable at higher temperatures. Figure 40 shows the
analog input current for various conditions. With the analog
input buffers disabled, the average input current to the AD7175-8
changes linearly with the differential input voltage at a rate of
48 µA /V.
If eight fully differential input paths are connected to the
AD7175-8, using adjacent analog input pins such as AIN0/AIN1
for the differential input pair is recommended. This is due to the
relative locations of these pins to each other. Decouple all analog
inputs to AVSS.
Single-Ended Inputs
CROSSPOINT MULTIPLEXER
The user can also choose to measure 16 different single-ended
analog inputs. In this case, each of the analog inputs is converted
as the difference between the single-ended input to be measured
and a set analog input common pin. Because there is a crosspoint
multiplexer, the user can set any of the analog inputs as the
common pin. An example of such a scenario is to connect the
AIN8 pin to AVSS or to the REFOUT voltage (that is, AVSS +
2.5 V) and select this input when configuring the crosspoint
multiplexer. When using the AD7175-8 with single-ended
inputs.
There are 17 analog input pins: AIN0 to AIN16. Each of these
pins connects to the internal crosspoint multiplexer. The
crosspoint multiplexer enables any of these inputs to be configured
as an input pair, either single-ended or fully differential. The
AD7175-8 can have up to 16 active channels. When more than
one channel is enabled, the channels are automatically sequenced
in order from the lowest enabled channel number to the highest
enabled channel number. The output of the multiplexer is
connected to the input of the integrated true rail-to-rail buffers.
These can be bypassed and the multiplexer output can be
directly connected to the switched-capacitor input of the ADC. The
simplified analog input circuit is shown in Figure 51.
Rev. 0 | Page 25 of 64
AD7175-8
Data Sheet
REF−/REF2− pin is connected directly to the AVSS potential.
On power-up of the AD7175-8, the internal reference is enabled
by default and is output on the REFOUT pin. When an external
reference is used instead of the internal reference to supply the
AD7175-8, attention must be paid to the output of the REFOUT
pin. If the internal reference is not being used elsewhere in the
application, ensure that the REFOUT pin is not hardwired to
AVSS because this draws a large current on power-up. On
power-up, if the internal reference is not being used, write to
the ADC mode register, disabling the internal reference. This is
controlled by the REF_EN bit (Bit 15) in the ADC mode
register, which is shown in Table 18.
AD7175-8 REFERENCE
The AD7175-8 offers the user the option of either supplying an
external reference to the REF+ and REF− or REF2+ and REF2-
pins of the device or allowing the use of the internal 2.5 V, low
noise, low drift reference. Select the reference source to be used by
the analog input by setting the REF_SELx bits (Bits[5:4]) in the
setup configuration registers appropriately. The structure of the
Setup Configuration 0 register is shown in Table 17. The
AD7175-8 defaults on power-up to use the internal 2.5 V
reference.
External Reference
The AD7175-8 has a fully differential reference input applied
through the REF+ and REF− or REF2+ and REF2 pins.
Standard low noise, low drift voltage references, such as the
ADR445, ADR444, and ADR441, are recommended for use.
Apply the external reference to the AD7175-8 reference pins as
shown in Figure 52. Decouple the output of any external
reference to AVSS. As shown in Figure 52, the ADR445 output is
decoupled with a 0.1 µF capacitor at its output for stability
purposes. The output is then connected to a 4.7 µF capacitor,
which acts as a reservoir for any dynamic charge required by the
ADC, and followed by a 0.1 µF decoupling capacitor at the
REF+ or REF2+ input. This capacitor is placed as close as
possible to the REF+/REF2+ and REF−/REF2− pins. The
Internal Reference
The AD7175-8 includes its own low noise, low drift voltage
reference. The internal reference has a 2.5 V output. The internal
reference is output on the REFOUT pin after the REF_EN bit in
the ADC mode register is set and is decoupled to AVSS with a
0.1 µF capacitor. The AD7175-8 internal reference is enabled by
default on power-up and is selected as the reference source for
the ADC. When using the internal reference, the INL performance
degrades as shown in Figure 23.
The REFOUT signal is buffered before being output to the pin.
The signal can be used externally in the circuit as a common-mode
source for external amplifier configurations.
AD7175-8
5.5V TO 18V
ADR4452
40
39
REF+
REF–
0.1µF
1
5V VREF
1
0.1µF
4.7µF
0.1µF
1
1
1
1
2
ALL DECOUPLING IS TO AVSS.
ANY OF THE ADRF440/ADR441/ADR443/ADR444/ADR445 FAMILY OF REFERENCES
CAN BE USED. THE ADR444 AND ADR441 BOTH ENABLE REUSE OF THE 5V
ANALOG SUPPLY NEEDED FOR AVDD1 TO POWER THE REFERENCE V
.
IN
Figure 52. External Reference ADR445 Connected to the AD7175-8 Reference Pins
Table 17. Setup Configuration 0 Register
Reg. Name
Bits
Bit 7
Bit 6
Bit 5
Bit 4
BI_UNIPOLAR0 REFBUF0+ REFBUF0− AINBUF0+ AINBUF0− 0x1320 RW
REF_SEL0 Reserved
Bit 3
Bit 2
Bit 1
Bit 0
Reset RW
0x20 SETUPCON0 [15:8]
[7:0]
Reserved
BURNOUT_EN0 Reserved
Table 18. ADC Mode Register
Reg.
Name
Bits
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
CLOCKSEL
Bit 1
Delay
Reserved
Bit 0
Reset
RW
0x01 ADCMODE [15:8]
[7:0]
REF_EN
Reserved
HIDE_DELAY
SING_CYC
Mode
Reserved
0xA000
RW
Rev. 0 | Page 26 of 64
Data Sheet
AD7175-8
exaggerated if the IOSTRENGTH bit is set at higher IOVDD
levels (see Table 28 for more information).
BUFFERED REFERENCE INPUT
The AD7175-8 has true rail-to-rail, integrated, precision unity
gain buffers on both ADC reference inputs. The buffers provide
the benefit of giving the user high input impedance and allow
high impedance external sources to be directly connected to the
reference inputs. The integrated reference buffers can fully drive
the internal reference switch capacitor sampling network,
simplifying the reference circuit requirements while consuming
a very efficient 2.9 mA typical per buffer. Each reference input
buffer amplifier is fully chopped, meaning that it minimizes the
offset error drift and 1/f noise of the buffer. When using an
external reference, such as the ADR445, ADR444, and ADR441,
these buffers are not required because these references, with
proper decoupling, can drive the reference inputs directly.
External Crystal
If higher precision, lower jitter clock sources are required, the
AD7175-8 can use an external crystal to generate the master
clock. The crystal is connected to the XTAL1 and XTAL2/CLKIO
pins. A recommended crystal for use is the FA-20H—a 16 MHz,
10 ppm, 9 pF crystal from Epson-Toyocom—which is available
in a surface-mount package. As shown in Figure 53, insert two
capacitors from the traces connecting the crystal to the XTAL1
and XTAL2/CLKIO pins. These capacitors allow for circuit
tuning. Connect these capacitors to the DGND pin. The value
for these capacitors depends on the length and capacitance of
the trace connections between the crystal and the XTAL1 and
XTAL2/CLKIO pins. Therefore, the values of these capacitors
differ depending on the PCB layout and the crystal employed.
CLOCK SOURCE
The AD7175-8 uses a nominal master clock of 16 MHz. The
AD7175-8 sources its sampling clock from one of three sources:
AD7175-8
Cx1
*
•
•
•
Internal oscillator
External crystal
External clock source
12
XTAL1
XTAL2/CLKIO 13
Cx2
All output data rates listed in the data sheet relate to a master
clock rate of 16 MHz. Using a lower clock frequency from, for
instance, an external source scales any listed data rate proportion-
ally. To achieve the specified data rates, particularly rates for the
rejection of 50 Hz and 60 Hz, use a 16 MHz clock. The source
of the master clock is selected by setting the CLOCKSEL bits
(Bits[3:2]) in the ADC mode register as shown in Table 18. The
default operation on power-up and reset of the AD7175-8 is to
operate with the internal oscillator. It is possible to fine tune the
output data rate and filter notch at low output data rates using
the SINC3_MAPx bit. See the Sinc3 Filter section for more
information.
*
*DECOUPLE TO DGND.
Figure 53. External Crystal Connections
The external crystal circuitry can be sensitive to the SCLK
edges, depending on SCLK frequency, IOVDD voltage, crystal
circuitry layout, and the crystal used. During crystal startup, any
disturbances caused by the SLCK edges may cause double edges
on the crystal input, resulting in invalid conversions until the
crystal voltage has reached a high enough level such that any
interference from the SCLK edges is insufficient to cause double
clocking. This double clocking can be avoided by ensuring that
the crystal circuitry has reached a sufficient voltage level after
startup before applying any SCLK signal.
Internal Oscillator
The internal oscillator runs at 16 MHz and can be used as the
ADC master clock. It is the default clock source for the AD7175-8
and is specified with an accuracy of 2.5%.
Due to the nature of the crystal circuitry, it is recommended
that empirical testing of the circuit be performed under the
required conditions, with the final PCB layout and crystal, to
ensure correct operation.
There is an option to allow the internal clock oscillator to be
output on the XTAL2/CLKIO pin. The clock output is driven
to the IOVDD logic level. Use of this option can affect the dc
performance of the AD7175-8 due to the disturbance intro-
duced by the output driver. The extent to which the performance is
affected depends on the IOVDD voltage supply. Higher IOVDD
voltages create a wider logic output swing from the driver and
affect performance to a greater extent. This effect is further
External Clock
The AD7175-8 can also use an externally supplied clock. In
systems where this is desirable, the external clock is routed to the
XTAL2/CLKIO pin. In this configuration, the XTAL2/CLKIO
pin accepts the externally sourced clock and routes it to the
modulator. The logic level of this clock input is defined by the
voltage applied to the IOVDD pin.
Rev. 0 | Page 27 of 64
AD7175-8
Data Sheet
DIGITAL FILTERS
The AD7175-8 has three flexible filter options to allow
optimization of noise, settling time, and rejection.
SINC3 FILTER
The sinc3 filter achieves the best single-channel noise performance
at lower rates and is, therefore, most suitable for single-channel
applications. The sinc3 filter always has a settling time, tSETTLE
•
•
•
Sinc5 + sinc1 filter
Sinc3 filter
Enhanced 50 Hz and 60 Hz rejection filters
,
equal to
t
SETTLE = 3/Output Data Rate
50Hz AND 60Hz
POSTFILTER
Figure 56 shows the frequency domain filter response for the
SINC1
SINC5
SINC3
sinc3 filter. The sinc3 filter has good roll-off over frequency and
has wide notches for good notch frequency rejection.
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
Figure 54. Digital Filter Block Diagram
The filter and output data rate are configured by setting the
appropriate bits in the filter configuration register for the
selected setup. Each channel can use a different setup and
therefore, a different filter and output data rate. See the Register
Details section for more information.
SINC5 + SINC1 FILTER
The sinc5 + sinc1 filter is targeted at multiplexed applications
and achieves single cycle settling at output data rates of 10 kSPS and
lower. The sinc5 block output is fixed at the maximum rate of
250 kSPS, and the sinc1 block output data rate can be varied to
control the final ADC output data rate. Figure 55 shows the
frequency domain response of the sinc5 + sinc1 filter at a 50 SPS
ODR. The sinc5 + sinc1 filter has a slow roll-off over frequency and
narrow notches.
–120
0
50
100
FREQUENCY (Hz)
150
Figure 56. Sinc3 Filter Response
The ODRs with the accompanying settling time and rms noise
for the sinc3 filter are shown in Table 21 and Table 22. It is possible
to finely tune the output data rate for the sinc3 filter by setting the
SINC3_MAPx bits in the filter configuration registers. If this bit is
set, the mapping of the filter register changes to directly program
the decimation rate of the sinc3 filter. All other options are
eliminated. The data rate when on a single channel can be
calculated using the following equation:
0
–20
–40
–60
fMOD
Output Data Rate =
32 × FILTCONx[14:0]
–80
where:
–100
–120
fMOD is the modulator rate (MCLK/2) and is 8 MHz for a
16 MHz MCLK.
FILTCONx[14:0] are the contents on the filter configuration
registers excluding the MSB.
0
50
100
FREQUENCY (Hz)
150
Figure 55. Sinc5 + Sinc1 Filter Response at 50 SPS ODR
For example, an output data rate of 50 SPS can be achieved with
SINC3_MAPx enabled by setting the FILTCONx[14:0] bits to a
value of 5000.
The ODRs with the accompanying settling time and rms noise
for the sinc5 + sinc1 filter are shown in Table 19 and Table 20.
Rev. 0 | Page 28 of 64
Data Sheet
AD7175-8
Figure 58 shows the same step on the analog input but with
single cycle settling enabled. The analog input requires at least a
single cycle for the output to be fully settled. The output data
SINGLE CYCLE SETTLING
By default, the AD7175-8 is configured with the SING_CYC bit
in the ADC mode register set so that only fully settled data is
output, effectively putting the ADC into a single cycle settling
mode. This mode achieves single cycle settling by reducing the
output data rate to be equal to the settling time of the ADC for the
selected output data rate. This bit has no effect with the sinc5 +
sinc1 filter at output data rates of 10 kSPS and lower.
RDY
rate, as indicated by the
signal, is now reduced to equal the
settling time of the filter at the selected output data rate.
ANALOG
INPUT
FULLY
SETTLED
ADC
OUTPUT
Figure 57 shows a step on the analog input with this mode
disabled and the sinc3 filter selected. The analog input requires
at least three cycles after the step change for the output to reach
the final settled value.
tSETTLE
Figure 58. Step Input with Single Cycle Settling
ANALOG
INPUT
FULLY
SETTLED
ADC
OUTPUT
1/ODR
Figure 57. Step Input Without Single Cycle Settling
Table 19. Output Data Rate, Settling Time, and Noise Using the Sinc5 + Sinc1 Filter with Input Buffers Disabled
Default Output Data
Output Data Rate
(SPS); SING_CYC =
0 and Single
Rate (SPS/Channel);
SING_CYC = 1 or with
Multiple Channels
Enabled1
Effective
Peak-to-Peak
Resolution with
5 V Reference
(Bits)
Notch
Frequency
(Hz)
Resolution with
5 V Reference
(Bits)
Settling
Time1
Noise
(µV rms)
Noise
Channel Enabled1
(µV p-p)2
50,000
41,667
31,250
27,778
20,833
17,857
12,500
10,000
5000
250,000
125,000
62,500
50,000
31,250
25,000
15,625
10,000
5000
2500
1000
500
397.5
200
100
59.92
49.96
20
16.66
10
20 µs
24 µs
32 µs
36 µs
48 µs
56 µs
80 µs
100 µs
200 µs
400 µs
1.0 ms
2.0 ms
2.516 ms
5.0 ms
10 ms
16.67 ms
20.016 ms
50.0 ms
60.02 ms
100 ms
200 ms
250,000
125,000
62,500
50,000
31,250
25,000
15,625
11,905
5435
2604
1016
504
400.00
200.64
100.16
59.98
50.00
20.01
8.7
7.2
5.5
5
4
3.6
2.9
2.5
20.1
20.4
20.8
20.9
21.3
21.4
21.7
21.9
22.5
23.0
23.6
24
24
24
24
24
24
24
24
24
65
60
43
41
32
29
22
18.3
12
8.2
5.2
3.2
3
17.2
17.3
17.8
17.9
18.3
18.4
18.8
19.1
19.7
20.2
20.9
21.6
21.7
22.3
22.9
23.1
23.3
24
1.7
1.2
2500
1000
0.77
0.57
0.5
0.36
0.25
0.19
0.18
0.11
0.1
500.0
397.5
200.0
100
59.92
49.96
20.00
16.66
10.00
5.00
2
1.3
1.1
0.95
0.6
0.45
0.4
0.34
16.66
10.00
5.00
24
24
24
0.08
0.07
5
24
1 The settling time is rounded to the nearest microsecond. This is reflected in the output data rate and channel switching rate. Channel switching rate = 1 ÷ settling time.
2 Measurement taken using 1000 samples.
Rev. 0 | Page 29 of 64
AD7175-8
Data Sheet
Table 20. Output Data Rate, Settling Time, and Noise Using the Sinc5 + Sinc1 Filter with Input Buffers Enabled
Default Output Data
Output Data Rate
(SPS); SING_CYC = 0
and Single Channel
Enabled1
Rate (SPS/Channel);
SING_CYC = 1 or with
Multiple Channels
Enabled1
Effective
Peak-to-Peak
Resolution with
5 V Reference
(Bits)
Notch
Frequency
(Hz)
Resolution with
5 V Reference
(Bits)
Settling
Time1
Noise
(µV rms)
Noise
(µV p-p)2
50,000
41,667
31,250
27,778
20,833
17,857
12,500
10,000
5000
250,000
125,000
62,500
50,000
31,250
25,000
15,625
10,000
5000
2500
1000
500
397.5
200
100
59.92
49.96
20
16.66
10
20 µs
24 µs
32 µs
36 µs
48 µs
56 µs
80 µs
100 µs
200 µs
400 µs
1.0 ms
2.0 ms
2.516 ms
5.0 ms
10 ms
16.67 ms
250,000
125,000
62,500
50,000
31,250
25,000
15,625
11,905
5435
2604
1016
504
400.00
200.64
100.16
59.98
9.8
8.4
6.4
5.9
4.8
4.3
3.4
3
20
85
66
55
49
39
33
26
23
16.8
17.2
17.5
17.6
18.0
18.2
18.6
18.7
19.3
19.9
20.7
21.3
21.4
22.1
22.5
23
20.2
20.6
20.7
21
21.1
21.5
21.7
22.2
22.7
23.4
23.8
24
24
24
24
24
24
24
24
24
2.1
1.5
16
10
2500
1000
0.92
0.68
0.6
0.43
0.32
0.23
0.2
0.14
0.13
0.1
5.7
3.9
3.7
2.2
1.7
1.2
1
0.75
0.66
0.47
0.32
500.0
397.5
200.0
100
59.92
49.96
20.00
16.66
10.00
5.00
20.016 ms 50.00
23.3
23.7
23.9
24
50.0 ms
60.02 ms
100 ms
200 ms
20.01
16.66
10.00
5.00
5
0.07
24
1 The settling time is rounded to the nearest microsecond. This is reflected in the output data rate and channel switching rate. Channel switching rate = 1 ÷ settling time.
2 Measurement taken using 1000 samples.
Rev. 0 | Page 30 of 64
Data Sheet
AD7175-8
Table 21. Output Data Rate, Settling Time, and Noise Using the Sinc3 Filter with Input Buffers Disabled
Default Output Data
Output Data Rate
(SPS); SING_CYC =
0 and Single
Rate (SPS/Channel);
SING_CYC = 1 or with
Multiple Channels
Enabled1
Effective
Peak-to-Peak
Resolution with
5 V Reference
(Bits)
Notch
Frequency
(Hz)
Resolution with
5 V Reference
(Bits)
Settling
Time1
Noise
(μV rms)
Noise
Channel Enabled1
(μV p-p)2
83,333
41,667
20,833
16,667
10,417
8333
5208
3333
1667
833
333.3
166.7
133.3
66.7
33.33
19.99
16.67
6.67
250,000
125,000
62,500
50,000
31,250
25,000
15,625
10,000
5000
2500
1000
500
400
200
100
60
50
20
16.67
10
5
12 μs
24 μs
48 μs
60 μs
96 μs
120 μs
192 μs
300 μs
6 μs
1.2 ms
3 ms
6 ms
7.5 ms
15 ms
30 ms
250,000
125,000
62,500
50,000
31,250
25,000
15,625
10,000
5000
2500
1000
500
400
210
28
5.2
4.2
3.2
2.9
2.2
1.8
1.3
0.91
0.56
0.44
0.4
0.25
0.2
0.13
0.13
0.08
0.07
0.06
0.05
15.5
18.4
20.9
21.2
21.6
21.7
22.1
22.4
22.9
23.4
24
24
24
24
24
24
24
24
24
1600
200
40
34
26
23
17
14
9.5
6
3.9
2.5
2.3
1.4
1
0.8
0.7
0.42
0.37
0.28
0.21
12.6
15.6
17.9
18.2
18.6
18.7
19.2
19.4
20
20.7
21.3
21.9
22.1
22.8
23.3
23.6
23.8
24
200
100
50.02 ms 59.98
60 ms
150 ms
180 ms
300 ms
600 ms
50
20
16.67
10
5
5.56
3.33
1.67
24
24
24
24
24
1 The settling time is rounded to the nearest microsecond. This is reflected in the output data rate and channel switching rate. Channel switching rate = 1 ÷ settling time.
2 Measurement taken using 1000 samples.
Rev. 0 | Page 31 of 64
AD7175-8
Data Sheet
Table 22. Output Data Rate, Settling Time, and Noise Using the Sinc3 Filter with Input Buffers Enabled
Default Output
Data Rate
Output Data Rate
(SPS);SING_CYC = 0
and Single Channel
Enabled1
(SPS/Channel);
SING_CYC = 1 or
with Multiple
Effective
Peak-to-Peak
Resolution with
5 V Reference
(Bits)
Notch
Frequency
(Hz)
Resolution with
5 V Reference
(Bits)
Settling
Time1
Noise
(µV rms)
Noise
Channels Enabled1
(µV p-p)2
83,333
41,667
20,833
16,667
10,417
8333
5208
3333
1667
833
333.3
166.7
133.3
66.7
33.33
19.99
16.67
6.67
250,000
125,000
62,500
50,000
31,250
25,000
15,625
10,000
5000
2500
1000
500
400
200
100
60
50
20
16.67
10
5
12 µs
24 µs
48 µs
60 µs
250,000
125,000
62,500
50,000
31,250
25,000
15,625
10,000
5000
2500
1000
500
400
200
100
59.98
50
210
28
5.8
4.9
3.8
3.4
2.6
2.1
1.5
15.5
18.4
20.7
21
21.3
21.5
21.9
22.2
22.7
23.1
23.7
24
24
24
24
24
24
24
24
24
1600
210
48
41
30
26
18
16
11
12.6
15.5
17.7
17.9
18.3
18.6
19.1
19.3
19.8
20.4
21.1
21.7
21.8
22.4
23
96 µs
120 µs
192 µs
300 µs
6 µs
1.2 ms
3 ms
1.1
7
4.5
3
0.71
0.52
0.41
0.32
0.2
0.17
0.15
0.13
0.12
0.1
6 ms
7.5 ms
15 ms
30 ms
50.02ms
60 ms
150 ms
180 ms
300 ms
600 ms
2.7
1.8
1.2
1.1
0.83
0.61
0.6
0.55
0.35
23.1
23.5
24
24
24
20
16.67
10
5.56
3.33
1.67
5
0.08
24
24
1 The settling time is rounded to the nearest microsecond. This is reflected in the output data rate and channel switching rate. Channel switching rate = 1 ÷ settling time.
2 Measurement taken using 1000 samples.
Rev. 0 | Page 32 of 64
Data Sheet
AD7175-8
sinc1 filter must be selected when using the enhanced filters to
achieve the specified settling time and noise performance. Table 23
shows the output data rates with the accompanying settling
time, rejection, and rms noise. Figure 59 to Figure 66 show the
frequency domain plots of the responses from the enhanced filters.
ENHANCED 50 HZ AND 60 HZ REJECTION FILTERS
The enhanced filters are designed to provide rejection of 50 Hz
and 60 Hz simultaneously and to allow the user to trade off
settling time and rejection. These filters can operate at up to
27.27 SPS or can reject up to 90 dB of 50 Hz 1 Hz and 60 Hz
1 Hz interference. These filters are realized by postfiltering
the output of the sinc5 + sinc1 filter. For this reason, the sinc5 +
Table 23. Enhanced Filters Output Data Rate, Noise, Settling Time, and Rejection Using the Enhanced Filters
Output Data Rate
(SPS)
Settling
Simultaneous Rejection of
Noise
Peak-to-Peak
Time (ms) 50 Hz 1 Hz and 60 Hz 1 Hz (dB)1 (μV rms) Resolution (Bits) Comments
Input Buffers Disabled
27.27
25
20
16.667
36.67
40.0
50.0
60.0
47
62
85
90
0.22
0.2
0.2
22.7
22.9
22.9
23
See Figure 59 and Figure 62
See Figure 60 and Figure 63
See Figure 61 and Figure 64
See Figure 65 and Figure 66
0.17
Input Buffers Enabled
27.27
25
20
36.67
40.0
50.0
60.0
47
62
85
90
0.22
0.22
0.21
0.21
22.7
22.7
22.8
22.8
See Figure 59 and Figure 62
See Figure 60 and Figure 63
See Figure 61 and Figure 64
See Figure 65 and Figure 66
16.667
1 Master clock = 16 MHz.
Rev. 0 | Page 33 of 64
AD7175-8
Data Sheet
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–100
0
40
45
50
55
60
65
70
100
200
300
400
500
600
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 62. 27.27 SPS ODR, 36.67 ms Settling Time at 50 Hz/60 Hz
Figure 59. 27.27 SPS ODR, 36.67 ms Settling Time
0
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–100
40
45
50
55
60
65
70
0
100
200
300
400
500
600
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 63. 25 SPS ODR, 40 ms Settling Time at 50 Hz/60 Hz
Figure 60. 25 SPS ODR, 40 ms Settling Time
0
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
40
45
50
55
60
65
70
0
100
200
300
400
500
600
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 61. 20 SPS ODR, 50 ms Settling Time
Figure 64. 20 SPS ODR, 50 ms Settling Time at 50 Hz/60 Hz
Rev. 0 | Page 34 of 64
Data Sheet
AD7175-8
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–100
0
100
200
300
400
500
600
40
45
50
55
60
65
70
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 65. 16.667 SPS ODR, 60 ms Settling Time
Figure 66. 16.667 SPS ODR, 60 ms Settling Time at 50 Hz/60 Hz
Rev. 0 | Page 35 of 64
AD7175-8
Data Sheet
OPERATING MODES
The AD7175-8 has a number of operating modes that can be set
from the ADC mode register and interface mode register (see
Table 27 and Table 28). These modes are as follows and are
described in the following sections:
register. When the data-word has been read from the data register,
RDY
the DOUT/
pin goes high. The user can read this register
additional times, if required. However, the user must ensure that
the data register is not being accessed at the completion of the
next conversion; otherwise, the new conversion word is lost.
•
•
•
•
•
•
Continuous conversion mode
Continuous read mode
Single conversion mode
Standby mode
Power-down mode
Calibration modes (three modes)
When several channels are enabled, the ADC automatically
sequences through the enabled channels, performing one
conversion on each channel. When all channels have been
converted, the sequence starts again with the first channel. The
channels are converted in order from lowest enabled channel to
highest enabled channel. The data register is updated as soon as
CONTINUOUS CONVERSION MODE
RDY
each conversion is available. The
output pulses low each
time a conversion is available. The user can then read the
conversion while the ADC converts the next enabled channel.
Continuous conversion is the default power-up mode. The
RDY
AD7175-8 converts continuously, and the
register goes low each time a conversion is complete. If
RDY
bit in the status
CS
is low,
output also goes low when a conversion is complete. To
If the DATA_STAT bit in the interface mode register is set to 1,
the contents of the status register, along with the conversion data,
are output each time the data register is read. The status register
indicates the channel to which the conversion corresponds.
the
read a conversion, the user writes to the communications
register, indicating that the next operation is a read of the data
CS
0x44
0x44
DIN
DATA
DATA
DOUT/RDY
SCLK
Figure 67. Continuous Conversion Mode
Rev. 0 | Page 36 of 64
Data Sheet
AD7175-8
To enable continuous read mode, set the CONTREAD bit in the
interface mode register. When this bit is set, the only serial interface
operations possible are reads from the data register. To exit con-
tinuous read mode, issue a dummy read of the ADC data register
CONTINUOUS READ MODE
In continuous read mode, it is not required to write to the
communications register before reading ADC data; apply only
RDY
the required number of SCLK pulses after
indicate the end of a conversion. When the conversion is
RDY
goes low to
RDY
command (0x44) while the
output is low. Alternatively, apply
CS
a software reset, that is, 64 SCLK pulses with
= 0 and DIN =
read,
returns high until the next conversion is available. In
1. This resets the ADC and all register contents. These are the
only commands that the interface recognizes after it is placed in
continuous read mode. Hold DIN low in continuous read mode
until an instruction is to be written to the device.
this mode, the data can be read only once. The user must also
ensure that the data-word is read before the next conversion is
complete. If the user has not read the conversion before the
completion of the next conversion or if insufficient serial clocks
are applied to the AD7175-8 to read the data-word, the serial
output register is reset shortly before the next conversion is
complete, and the new conversion is placed in the output serial
register. The ADC must be configured for continuous
conversion mode to use continuous read mode.
If multiple ADC channels are enabled, each channel is output
in turn, with the status bits being appended to the data if
DATA_STAT is set in the interface mode register. The status
register indicates the channel to which the conversion corresponds.
CS
0x02
0x0080
DIN
DATA
DATA
DATA
DOUT/RDY
SCLK
Figure 68. Continuous Read Mode
Rev. 0 | Page 37 of 64
AD7175-8
Data Sheet
RDY
available, the
output goes low. The ADC then selects the next
SINGLE CONVERSION MODE
channel and begins a conversion. The user can read the present
conversion while the next conversion is being performed. As soon
as the next conversion is complete, the data register is updated;
therefore, the user has a limited period in which to read the
conversion. When the ADC has performed a single conversion
on each of the selected channels, it returns to standby mode.
In single conversion mode, the AD7175-8 performs a single
conversion and is placed in standby mode after the conversion
RDY
is complete. The
of a conversion. When the data-word has been read from the
RDY
output goes low to indicate the completion
data register, the DOUT/
pin goes high. The data register
RDY
can be read several times, if required, even when the DOUT/
pin has gone high.
If the DATA_STAT bit in the interface mode register is set to 1,
the contents of the status register, along with the conversion, are
output each time the data register is read. The two LSBs of the
status register indicate the channel to which the conversion
corresponds.
If several channels are enabled, the ADC automatically
sequences through the enabled channels and performs a
conversion on each channel. When a conversion is started, the
RDY
DOUT/
pin goes high and remains high until a valid
CS
conversion is available and is low. As soon as the conversion is
CS
0x01
0x8010
0x44
DIN
DATA
DOUT/RDY
SCLK
Figure 69. Single Conversion Mode
Rev. 0 | Page 38 of 64
Data Sheet
AD7175-8
To start a calibration, write the relevant value to the mode bits
STANDBY AND POWER-DOWN MODES
RDY
RDY
in the ADC mode register. The DOUT/
pin and the
In standby mode, most blocks are powered down. The LDOs
remain active so that registers maintain their contents. The
internal reference remains active if enabled, and the crystal
oscillator remains active if selected. To power down the
reference in standby mode, set the REF_EN bit in the ADC
mode register to 0. To power down the clock in standby mode,
set the CLOCKSEL bits in the ADC mode register to 00
(internal oscillator).
bit in the status register go high when the calibration initiates.
When the calibration is complete, the contents of the correspond-
RDY
ing offset or gain register are updated, the
bit in the status
RDY
CS
is
register is reset and the
output pin returns low (if
low), and the AD7175-8 reverts to standby mode.
During an internal offset calibration, the selected positive
analog input pin is disconnected, and both modulator inputs
are connected internally to the selected negative analog input
pin. For this reason, it is necessary to ensure that the voltage on
the selected negative analog input pin does not exceed the
allowed limits and is free from excessive noise and interference.
In power-down mode, all blocks are powered down, including
the LDOs. All registers lose their contents, and the GPIOx outputs
are placed in three-state. To prevent accidental entry to power-
down mode, the ADC must first be placed in standby mode.
CS
Exiting power-down mode requires 64 SCLK pulses with
= 0
System calibrations, however, expect the system zero-scale
(offset) and system full-scale (gain) voltages to be applied to the
ADC pins before initiating the calibration modes. As a result,
errors external to the ADC are removed.
and DIN = 1, that is, a serial interface reset. A delay of 500 µs is
recommended before issuing a subsequent serial interface
command to allow the LDO to power up.
Figure 19 shows the internal reference settling time after
returning from standby mode (setting REF_EN = 0 and then 1)
and returning from power down.
From an operational point of view, treat a calibration like
another ADC conversion. An offset calibration, if required,
must always be performed before a full-scale calibration. Set the
RDY
system software to monitor the
bit in the status register or
output to determine the end of a calibration via a
CALIBRATION
RDY
the
The AD7175-8 allows a two-point calibration to be performed
to eliminate any offset and gain errors. Three calibration modes
eliminate these offset and gain errors on a per setup basis:
polling sequence or an interrupt driven routine. All calibrations
require a time equal to the settling time of the selected filter and
output data rate to be completed.
•
•
•
Internal zero-scale calibration mode
System zero-scale calibration mode
System full-scale calibration mode
An internal offset calibration, system zero-scale calibration, and
system full-scale calibration can be performed at any output data
rate. Using lower output data rates results in better calibration
accuracy and is accurate for all output data rates. A new offset
calibration is required for a given channel if the reference source
for that channel is changed.
There is no internal full-scale calibration mode because this is
calibrated in the factory at the time of production.
Only one channel can be active during calibration. After each
conversion, the ADC conversion result is scaled using the ADC
calibration registers before being written to the data register.
The offset error is typically 60 µV and an offset calibration
reduces the offset error to the order of the noise. The gain error
is factory calibrated at ambient temperature. Following this
calibration, the gain error is typically 80 ppm of FSR.
The default value of the offset register is 0x800000, and the
nominal value of the gain register is 0x555555. The calibration
range of the ADC gain is from 0.4 × VREF to 1.05 × VREF. The
following equations show the calculations that are used. In
unipolar mode, the ideal relationship—that is, not taking into
account the ADC gain error and offset error—is as follows:
The AD7175-8 provides the user with access to the on-chip
calibration registers, allowing the microprocessor to read the
calibration coefficients of the device and to write its own
calibration coefficients. A read or write of the offset and gain
registers can be performed at any time except during an internal
or self calibration.
0.75×VIN
VREF
Gain
0x400000
Data =
×223
−
(
Offset − 0x800000
)
×
×2
In bipolar mode, the ideal relationship—that is, not taking into
account the ADC gain error and offset error—is as follows:
0.75 ×VIN
×223
−
(
Offset − 0x800000
)
×
Data =
VREF
Gain
0x400000
+ 0x800000
Rev. 0 | Page 39 of 64
AD7175-8
Data Sheet
DIGITAL INTERFACE
The programmable functions of the AD7175-8 are controlled via
the SPI serial interface. The serial interface of the AD7175-8
For CRC checksum calculations during a write operation, the
following polynomial is always used:
x8 + x2 + x + 1
CS
RDY
consists of four signals: , DIN, SCLK, and DOUT/
. The
DIN input is used to transfer data into the on-chip registers, and
the DOUT output is used to access data from the on-chip
registers. SCLK is the serial clock input for the device, and all data
transfers (either on the DIN input or on the DOUT output) occur
with respect to the SCLK signal.
During read operations, the user can select between this
polynomial and a simpler exclusive OR (XOR) function. The
XOR function requires less time to process on the host
microcontroller than the polynomial-based checksum. The
CRC_EN bits in the interface mode register enable and disable
the checksum and allow the user to select between the
polynomial check and the simple XOR check.
RDY
The DOUT/
the output going low if
available in the data register. The
a read operation from the data register is complete. The
pin also functions as a data ready signal, with
CS
is low when a new data-word is
RDY
output is reset high when
RDY
The checksum is appended to the end of each read and write
transaction. The checksum calculation for the write transaction
is calculated using the 8-bit command word and the 8-bit to
24-bit data. For a read transaction, the checksum is calculated
using the command word and the 8-bit to 32-bit data output.
Figure 70 and Figure 71 show SPI write and read transactions,
respectively.
output also goes high before updating the data register to
indicate when not to read from the device to ensure that a data
read is not attempted while the register is being updated. Take
RDY
care to avoid reading from the data register when the
output is about to go low. The best method to ensure that no data
RDY
read occurs is to always monitor the
output; start reading
output goes low; and
ensure a sufficient SCLK rate, such that the read is complete
CS
8-BIT COMMAND
UP TO 24-BIT INPUT
8-BIT CRC
RDY
the data register as soon as the
CS
before the next conversion result.
is used to select a device. It
CS
DATA
CRC
DIN
can be used to decode the AD7175-8 in systems where several
components are connected to the serial bus.
SCLK
Figure 2 and Figure 3 show timing diagrams for interfacing to
CS
the AD7175-8 using
to decode the device. Figure 2 shows
Figure 70. SPI Write Transaction with CRC
the timing for a read operation from the AD7175-8, and Figure 3
shows the timing for a write operation to the AD7175-8. It is
possible to read from the data register several times even though
UP TO
8-BIT COMMAND
32-BIT OUTPUT
8-BIT CRC
CS
RDY
the
output returns high after the first read operation.
However, care must be taken to ensure that the read operations are
completed before the next output update occurs. In continuous
read mode, the data register can be read only once.
CMD
DIN
DOUT/
RDY
DATA
CRC
CS
The serial interface can operate in 3-wire mode by tying
low.
pins are used to
communicate with the AD7175-8. The end of the conversion
RDY
RDY
In this case, the SCLK, DIN, and DOUT/
SCLK
can also be monitored using the
bit in the status register.
CS
The AD7175-8 can be reset by writing 64 SCLKs with
= 0
Figure 71. SPI Read Transaction with CRC
and DIN = 1. A reset returns the interface to the state in which it
expects a write to the communications register. This operation
resets the contents of all registers to their power-on values.
Following a reset, allow a period of 500 µs before addressing the
serial interface.
If checksum protection is enabled when continuous read mode
is active, an implied read data command of 0x44 before every
data transmission must be accounted for when calculating the
checksum value. This implied read data command ensures a
nonzero checksum value even if the ADC data equals 0x000000.
CHECKSUM PROTECTION
The AD7175-8 has a checksum mode that can be used to
improve interface robustness. Using the checksum ensures that
only valid data is written to a register and allows data read from
a register to be validated. If an error occurs during a register
write, the CRC_ERROR bit is set in the status register. However,
to ensure that the register write is successful, read back the
register and verify the checksum.
Rev. 0 | Page 40 of 64
Data Sheet
AD7175-8
To generate the checksum, the data is left shifted by eight bits to
create a number ending in eight Logic 0s. The polynomial is
aligned so that its MSB is adjacent to the leftmost Logic 1 of the
data. An XOR function is applied to the data to produce a new,
shorter number. The polynomial is again aligned so that its MSB is
adjacent to the leftmost Logic 1 of the new result, and the proce-
dure is repeated. This process repeats until the original data is
reduced to a value less than the polynomial. This is the 8-bit
checksum.
CRC CALCULATION
Polynomial
The checksum, which is eight bits wide, is generated using the
polynomial
x8 + x2 + x + 1
Example of a Polynomial CRC Calculation—24-Bit Word: 0x654321 (Eight Command Bits and 16-Bit Data)
An example of generating the 8-bit checksum using the polynomial based checksum is as follows:
Initial value
011001010100001100100001
01100101010000110010000100000000
left shifted eight bits
polynomial
x8 + x2 + x + 1
=
100000111
100100100000110010000100000000
100000111
XOR result
polynomial
XOR result
polynomial
XOR result
polynomial value
XOR result
polynomial value
XOR result
polynomial value
XOR result
polynomial value
XOR result
polynomial value
XOR result
polynomial value
XOR result
polynomial value
XOR result
polynomial value
XOR result
polynomial value
XOR result
polynomial value
checksum = 0x86
100011000110010000100000000
100000111
11111110010000100000000
100000111
1111101110000100000000
100000111
111100000000100000000
100000111
11100111000100000000
100000111
1100100100100000000
100000111
100101010100000000
100000111
101101100000000
100000111
1101011000000
100000111
101010110000
100000111
1010001000
100000111
10000110
Rev. 0 | Page 41 of 64
AD7175-8
Data Sheet
XOR Calculation
The checksum, which is 8 bits wide, is generated by splitting the data into bytes and then performing an XOR of the bytes.
Example of an XOR Calculation—24-Bit Word: 0x654321 (Eight Command Bits and 16-Bit Data)
Using the previous example of a polynomial CRC calculation, divide the data into three bytes: 0x65, 0x43, and 0x21
01100101
01000011
00100110
00100001
00000111
0x65
0x43
XOR result
0x21
CRC
Rev. 0 | Page 42 of 64
Data Sheet
AD7175-8
INTEGRATED FUNCTIONS
The AD7175-8 has integrated functions that improve the
usefulness of a number of applications as well as serve
diagnostic purposes in safety conscious applications.
time, the delay can be absorbed by reducing the number of
averages the digital filter performs, which keeps the conversion
time the same but can affect the noise performance.
The effect on the noise performance depends on the delay time
compared to the conversion time. It is possible to absorb the
delay only for output data rates less than 10 kSPS with the
exception of the following four rates, which cannot absorb any
delay: 397.5 SPS, 59.92 SPS, 49.96 SPS, and 16.66 SPS.
GENERAL-PURPOSE I/O
The AD7175-8 has two general-purpose digital input/output
pins (GPIO0, GPIO1) and two general-purpose digital output
pins (GPO2, GPO3). As the naming convention suggests, the
GPIO0 and GPIO1 pins can be configured as inputs or outputs,
but GPO2 and GPO3 are outputs only. The GPIOx and GPOx
pins are enabled using the following bits in the GPIOCON
register: IP_EN0, IP_EN1 (or OP_EN0, OP_EN1) for GPIO0
and GPIO1, and OP_EN2_3 for GPO2 and GPO3.
16-BIT/24-BIT CONVERSIONS
By default, the AD7175-8 generates 24-bit conversions.
However, the width of the conversions can be reduced to 16 bits.
Setting the WL16 bit in the interface mode register to 1 rounds
all data conversions to 16 bits. Clearing this bit sets the width of
the data conversions to 24 bits.
When the GPIO0 or GPIO1 pin is enabled as an input, the logic
level at the pin is contained in the GP_DATA0 or GP_DATA1 bit,
respectively. When the GPIO0, GPIO1, GPO2, or GPO3 pin is
enabled as an output, the GP_DATA0, GP_DATA1, GP_DATA2,
or GP_DATA3 bit, respectively, determines the logic level output
at the pin. The logic levels for these pins are referenced to AVDD1
and AVSS; therefore, outputs have an amplitude of 5 V.
DOUT_RESET
RDY
The serial interface uses a shared DOUT/
pin. By default,
signal. During a data read, this pin
outputs the data from the register being read. After the read is
RDY
RDY
this pin outputs the
complete, the pin reverts to outputting the
signal after a
ERROR
The
When the ERR_EN bits in the GPIOCON register are set to 11,
ERROR
pin can also be used as a general-purpose output.
short fixed period of time (t7). However, this time may be too
short for some microcontrollers and can be extended until
the
pin operates as a general-purpose output. In this
CS
the
pin is brought high by setting the DOUT_RESET bit in
CS
configuration, the ERR_DAT bit in the GPIOCON register
determines the logic level output at the pin. The logic level for the
pin is referenced to IOVDD and DGND.
the interface mode register to 1. This means that
must be
used to frame each read operation and compete the serial
interface transaction.
ERROR
Both GPIOs and the
pin, when set as general-purpose
SYNCHRONIZATION
Normal Synchronization
outputs, have an active pull-up circuit.
EXTERNAL MULTIPLEXER CONTROL
When the SYNC_EN bit in the GPIOCON register is set to 1,
If an external multiplexer is used to increase the channel count,
the multiplexer logic pins can be controlled via the AD7175-8
GPIOx pins. With the MUX_IO bit, the GPIOx timing is
controlled by the ADC; therefore, the channel change is
synchronized with the ADC, eliminating any need for external
synchronization.
SYNC
SYNC
pin functions as a synchronization input. The
the
input lets the user reset the modulator and the digital filter
without affecting any of the setup conditions on the device. This
feature lets the user start to gather samples of the analog input
SYNC
from a known point, the rising edge of the
input.
SYNC
The
input must be low for at least one master clock cycle
DELAY
to ensure that synchronization occurs.
It is possible to insert a programmable delay before the AD7175-8
begins to take samples. This delay allows an external amplifier
or multiplexer to settle and can alleviate the specification
requirements for the external amplifier or multiplexer. Eight
programmable settings, ranging from 0 µs to 1 ms, can be set
using the delay bits in the ADC mode register (Register 0x01,
Bits[10:8]).
If multiple AD7175-8 devices are operated from a common
master clock, they can be synchronized so that their analog
inputs are sampled simultaneously. This synchronization is
normally done after each AD7175-8 device has performed its
own calibration or has calibration coefficients loaded into its
SYNC
calibration registers. A falling edge on the
digital filter and the analog modulator and places the AD7175-8
SYNC
input resets the
If a delay greater than 0 µs is selected and the HIDE_DELAY bit
in the ADC mode register is set to 0, this delay is added to the
conversion time, regardless of the selected output data rate.
into a consistent known state. While the
input is low, the
SYNC
AD7175-8 is maintained in this known state. On the
input rising edge, the modulator and filter are taken out of this
reset state, and on the next master clock edge, the device starts to
gather input samples again.
When using the sinc5 + sinc1 filter, it is possible to hide this
delay such that the output data rate remains the same as the output
data rate without the delay enabled. If the HIDE_DELAY bit is
set to 1 and the selected delay is less than half of the conversion
The device is taken out of reset on the master clock falling edge
SYNC
following the
input low to high transition. Therefore,
Rev. 0 | Page 43 of 64
AD7175-8
Data Sheet
SYNC
REG_ERROR
when multiple devices are being synchronized, take the
input high on the master clock rising edge to ensure that all
devices are released on the master clock falling edge. If
The REG_ERROR flag is used in conjunction with the
REG_CHECK bit in the interface mode register. When the
REG_CHECK bit is set, the AD7175-8 monitors the values in
the on-chip registers. If a bit changes, the REG_ERROR bit is
set. Therefore, for writes to the on-chip registers, set REG_CHECK
to 0. When the registers have been updated, the REG_CHECK
bit can be set to 1. The AD7175-8 calculates a checksum of the
on-chip registers. If one of the register values has changed, the
REG_ERROR bit is set. If an error is flagged, set REG_CHECK
to 0 to clear the REG_ERROR bit in the status register. The
register check function does not monitor the data register,
status register, or interface mode register.
SYNC
the
input is not taken high in sufficient time, a difference
of one master clock cycle between the devices is possible; that
is, the instant at which conversions are available differs from
device to device by a maximum of one master clock cycle.
SYNC
The
command for a single channel when in normal synchronization
SYNC
input can also be used as a start conversion
mode. In this mode, the rising edge of the
RDY
input starts a
output indicates
conversion, and the falling edge of the
when the conversion is complete. The settling time of the filter is
required for each data register update. After the conversion is
ERROR
Input/Output
SYNC
complete, bring the
conversion start signal.
input low in preparation for the next
ERROR
The
pin functions as an error input/output pin or a
general-purpose output pin. The ERR_EN bits in the GPIOCON
register determine the function of the pin.
Alternate Synchronization
SYNC
In alternate synchronization mode, the
input operates as
ERROR
When ERR_EN is set to 10, the
open-drain error output,
pin functions as an
a start conversion command when several channels of the
AD7175-8 are enabled. Setting the ALT_SYNC bit in the interface
mode register to 1 enables an alternate synchronization scheme.
SYNC
ERROR
. The three error bits in the
status register (ADC_ERROR, CRC_ERROR, and
REG_ERROR) are OR’ed, inverted, and mapped to the
ERROR
When the
input is taken low, the ADC completes the
conversion on the current channel, selects the next channel in
SYNC
to commence the conversion. The
ERROR
output. Therefore, the
output indicates that an error
the sequence, and then waits until the
RDY
input is taken high
output goes low when
has occurred. The status register must be read to identify the
error source.
the conversion is complete on the current channel, and the data
register is updated with the corresponding conversion.
ERROR
When ERR_EN is set to 01, the
pin functions as an
. The error output of another component
ERROR
ERROR
error input,
can be connected to the AD7175-8
AD7175-8 indicates when an error occurs on either itself or the
ERROR
SYNC
Therefore, the
input does not interfere with the sampling
input so that the
on the currently selected channel but allows the user to control
the instant at which the conversion begins on the next channel
in the sequence.
external component. The value on the
input is inverted
and OR’e d with the errors from the ADC conversion, and the
result is indicated via the ADC_ERROR bit in the status register.
Alternate synchronization mode can be used only when several
channels are enabled. It is not recommended to use this mode
when a single channel is enabled.
ERROR
The value of the
in the GPIO configuration register.
ERROR
input is reflected in the ERR_DAT bit
ERROR FLAGS
The
input/output is disabled when ERR_EN is set to 00.
The status register contains three error bits—ADC_ERROR,
CRC_ERROR, and REG_ERROR—that flag errors with the
ADC conversion, errors with the CRC check, and errors caused
ERROR
pin operates
When the ERR_EN bits are set to 11, the
as a general-purpose output.
DATA_STAT
ERROR
by changes in the registers, respectively. In addition, the
output can indicate that an error has occurred.
The contents of the status register can be appended to each con-
version on the AD7175-8. This function is useful if several
channels are enabled. Each time a conversion is output, the
contents of the status register are appended. The two LSBs of
the status register indicate to which channel the conversion
corresponds. In addition, the user can determine if any errors
are being flagged by the error bits.
ADC_ERROR
The ADC_ERROR bit in the status register flags any errors that
occur during the conversion process. The flag is set when an over-
range or underrange result is output from the ADC. The ADC
also outputs all 0s or all 1s when an undervoltage or overvoltage
occurs. This flag is reset only when the overvoltage or undervoltage
is removed. It is not reset by a read of the data register.
IOSTRENGTH
The serial interface can operate with a power supply as low as
CRC_ERROR
RDY
2 V. However, at this low voltage, the DOUT/
pin may not
If the CRC value that accompanies a write operation does not
correspond with the information sent, the CRC_ERROR flag is
set. The flag is reset as soon as the status register is explicitly read.
have sufficient drive strength if there is moderate parasitic
capacitance on the board or the SCLK frequency is high. The
Rev. 0 | Page 44 of 64
Data Sheet
AD7175-8
IOSTRENGTH bit in the interface mode register increases the
selected in the same way as an analog input channel. The
temperature sensor requires that the analog input buffers be
enabled on both analog inputs. If the buffers are not enabled,
selecting the temperature sensor as an input forces the buffers
to be enabled during the conversion.
RDY
drive strength of the DOUT/
pin.
POWER-DOWN SWITCH
Setting the PDSW bit in the GPIO configuration register allows
the PDSW pin to sink current. This function can be used in
applications where the switch controls the power-up/power-
down of the analog front-end sensor, for example, a bridge
sensor. The PDSW pin can sink 16 mA maximum.
To use the temperature sensor, the first step is to calibrate the
device in a known temperature (25°C) and take a conversion as
a reference point. The temperature sensor has a nominal
sensitivity of 470 µV/K; use the difference in this ideal slope and
the slope measured to calibrate the temperature sensor. The
temperature sensor is specified with a 2°C typical accuracy
after calibration at 25°C. The temperature can be calculated as
follows:
INTERNAL TEMPERATURE SENSOR
The AD7175-8 has an integrated temperature sensor. The
temperature sensor can be used as a guide for the ambient
temperature at which the device is operating. This can be used
for diagnostic purposes or as an indicator of when the applica-
tion circuit needs to rerun a calibration routine to take into
account a shift in operating temperature. The temperature
sensor is selected using the crosspoint multiplexer and is
Conversion Result
Temperature (°C) =
– 273.15
470 μV
Rev. 0 | Page 45 of 64
AD7175-8
Data Sheet
GROUNDING AND LAYOUT
The analog inputs and reference inputs are differential and,
therefore, most of the voltages in the analog modulator are
common-mode voltages. The high common-mode rejection of
the device removes common-mode noise on these inputs. The
analog and digital supplies to the AD7175-8 are independent
and connected to separate pins to minimize coupling between the
analog and digital sections of the device. The digital filter
provides rejection of broadband noise on the power supplies,
except at integer multiples of the master clock frequency.
possible to provide low impedance paths and reduce glitches on
the power supply line. Shield fast switching signals like clocks
with digital ground to prevent radiating noise to other sections
of the board and never run clock signals near the analog inputs.
Avoid crossover of digital and analog signals. Run traces on
opposite sides of the board at right angles to each other. This
technique reduces the effects of feedthrough on the board. A
microstrip technique is by far the best method but is not always
possible with a double sided board.
The digital filter also removes noise from the analog and
reference inputs, provided that these noise sources do not
saturate the analog modulator. As a result, the AD7175-8 is
more immune to noise interference than a conventional high
resolution converter. However, because the resolution of the
AD7175-8 is high and the noise levels from the converter are so
low, take care with regard to grounding and layout.
Good decoupling is important when using high resolution ADCs.
The AD7175-8 has three power supply pins—AVDD1, AVDD2,
and IOVDD. The AVDD1 and AVDD2 pins are referenced to
AVSS, and the IOVDD pin is referenced to DGND. Decouple
AVDD1 and AVDD2 with a 10 µF capacitor in parallel with a
0.1 µF capacitor to AVSS on each pin. Place the 0.1 µF capacitor
as close as possible to the device on each supply, ideally right up
against the device. Decouple IOVDD with a 10 µF capacitor in
parallel with a 0.1 µF capacitor to DGND. Decouple all analog
inputs to AVSS. If an external reference is used, decouple the
REF+ and REF− pins to AVSS.
The PCB that houses the ADC must be designed such that the
analog and digital sections are separated and confined to
certain areas of the board. A minimum etch technique is
generally best for ground planes because it results in the best
shielding.
The AD7175-8 also has two on-board LDO regulators—one
that regulates the AVDD2 supply and one that regulates the
IOVDD supply. For the REGCAPA pin, it is recommended that
1 µF and 0.1 µF capacitors to AVSS be used. Similarly, for the
REGCAPD pin, it is recommended that 1 µF and 0.1 µF
capacitors to DGND be used.
In any layout, the user must consider the flow of currents in the
system, ensuring that the paths for all return currents are as close as
possible to the paths the currents took to reach their destinations.
Avoid running digital lines under the device because this
couples noise onto the die and allows the analog ground plane
to run under the AD7175-8 to prevent noise coupling. The
power supply lines to the AD7175-8 must use as wide a trace as
If using the AD7175-8 for split supply operation, a separate
plane must be used for AVSS.
Rev. 0 | Page 46 of 64
Data Sheet
AD7175-8
REGISTER SUMMARY
Table 24. Register Summary
Reg. Name
Bits
[7:0]
[7:0]
Bit 7
WEN
RDY
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
0x00
RW
W
0x00 COMMS
0x00 STATUS
0x01 ADCMODE
W
RA
R/
ADC_ERROR
HIDE_DELAY
CRC_ERROR
REG_ERROR
CHANNEL
0x80
R
[15:8] REF_EN
SING_CYC
MODE
RESERVED
DELAY
RESERVED
DOUT_RESET 0x0000
0xA000
RW
[7:0]
RESERVED
CLOCKSEL
IOSTRENGTH
CRC_EN
0x02 IFMODE
[15:8]
[7:0]
RESERVED
ALT_SYNC
RESERVED
RESERVED
RW
R
CONTREAD
DATA_STAT
REG_CHECK
RESERVED WL16
0x03 REGCHECK
[23:16]
[15:8]
[7:0]
REGISTER_CHECK[23:16]
REGISTER_CHECK[15:8]
REGISTER_CHECK[7:0]
DATA[23:16]
0x000000
0x04 DATA
[23:16]
[15:8]
[7:0]
0x000000
R
DATA[15:8]
DATA[7:0]
0x06 GPIOCON
0x07 ID
[15:8]
[7:0]
RESERVED
GP_DATA3
PDSW
OP_EN2_3 MUX_IO
IP_EN0
SYNC_EN
OP_EN1
ERR_EN
GP_DATA1
ERR_DAT
0x0800
0x3CDx
0x8001
0x0001
0x0001
0x0001
0x0001
RW
R
GP_DATA2 IP_EN1
OP_EN0
GP_DATA0
[15:8]
[7:0]
ID[15:8]
ID[7:0]
0x10 CH0
0x11 CH1
0x12 CH2
0x13 CH3
0x14 CH4
[15:8] CH_EN0
[7:0]
SETUP_SEL0
RESERVED
AINNEG0
RESERVED
AINNEG1
RESERVED
AINNEG2
RESERVED
AINNEG3
RESERVED
AINNEG4
RESERVED
AINNEG5
RESERVED
AINNEG6
RESERVED
AINNEG7
RESERVED
AINNEG8
RESERVED
AINNEG9
RESERVED
AINNEG10
RESERVED
AINNEG11
RESERVED
AINNEG12
RESERVED
AINNEG13
RESERVED
AINNEG14
RESERVED
AINNEG15
REFBUF0−
RESERVED
AINPOS0[4:3]
RW
RW
RW
RW
RW
AINPOS0[2:0]
AINPOS1[2:0]
AINPOS2[2:0]
AINPOS3[2:0]
[15:8] CH_EN1
[7:0]
SETUP_SEL1
SETUP_SEL2
SETUP_SEL3
SETUP_SEL4
AINPOS1[4:3]
AINPOS2[4:3]
AINPOS3[4:3]
AINPOS4[4:3]
[15:8] CH_EN2
[7:0]
[15:8] CH_EN3
[7:0]
[15:8] CH_EN4
[7:0]
AINPOS4[2:0]
AINPOS5[2:0]
AINPOS6[2:0]
AINPOS7[2:0]
AINPOS8[2:0]
AINPOS9[2:0]
AINPOS10[2:0]
AINPOS11[2:0]
AINPOS12[2:0]
AINPOS13[2:0]
AINPOS14[2:0]
0x15 CH5
0x16 CH6
0x17 CH7
0x18 CH8
0x19 CH9
0x1A CH10
0x1B CH11
0x1C CH12
0x1D CH13
0x1E CH14
0x1F CH15
[15:8] CH_EN5
[7:0]
SETUP_SEL5
SETUP_SEL6
SETUP_SEL7
SETUP_SEL8
SETUP_SEL9
SETUP_SEL10
SETUP_SEL11
SETUP_SEL12
SETUP_SEL13
SETUP_SEL14
SETUP_SEL15
AINPOS5[4:3]
AINPOS6[4:3]
AINPOS7[4:3]
AINPOS8[4:3]
AINPOS9[4:3]
AINPOS10[4:3]
AINPOS11[4:3]
AINPOS12[4:3]
AINPOS13[4:3]
AINPOS14[4:3]
AINPOS15[4:3]
0x0001
0x0001
0x0001
0x0001
0x0001
0x0001
0x0001
0x0001
0x0001
0x0001
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
[15:8] CH_EN6
[7:0]
[15:8] CH_EN7
[7:0]
[15:8] CH_EN8
[7:0]
[15:8] CH_EN9
[7:0]
[15:8] CH_EN10
[7:0]
[15:8] CH_EN11
[7:0]
[15:8] CH_EN12
[7:0]
[15:8] CH_EN13
[7:0]
[15:8] CH_EN14
[7:0]
[15:8] CH_EN15
[7:0]
0x0001
0x1320
0x1320
0x1320
0x1320
0x1320
RW
RW
RW
RW
RW
RW
AINPOS15[2:0]
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
0x20 SETUPCON0 [15:8]
BI_UNIPOLAR0
REF_SEL0
BI_UNIPOLAR1
REF_SEL1
BI_UNIPOLAR2
REF_SEL2
BI_UNIPOLAR3
REF_SEL3
BI_UNIPOLAR4
REF_SEL4
Rev. 0 | Page 47 of 64
REFBUF0+
AINBUF0+
AINBUF0−
AINBUF1−
AINBUF2−
AINBUF3−
AINBUF4−
[7:0]
BURNOUT_EN0
BURNOUT_EN1
BURNOUT_EN2
BURNOUT_EN3
BURNOUT_EN4
0x21 SETUPCON1 [15:8]
REFBUF1+
REFBUF2+
REFBUF3+
REFBUF4+
REFBUF1−
AINBUF1+
[7:0]
RESERVED
0x22 SETUPCON2 [15:8]
REFBUF2−
REFBUF3−
AINBUF2+
[7:0]
0x23 SETUPCON3 [15:8]
[7:0]
RESERVED
AINBUF3+
RESERVED
0x24 SETUPCON4 [15:8]
[7:0]
REFBUF4−
AINBUF4+
RESERVED
AD7175-8
Data Sheet
Reg. Name
Bits
Bit 7
BURNOUT_EN5
Bit 6
Bit 5
Bit 4
BI_UNIPOLAR5
REF_SEL5
BI_UNIPOLAR6
REF_SEL6
BI_UNIPOLAR7
REF_SEL7
RESERVED
ORDER0
Bit 3
REFBUF5+
Bit 2
Bit 1
AINBUF5+
Bit 0
AINBUF5−
Reset
RW
0x25 SETUPCON5 [15:8]
RESERVED
REFBUF5−
0x1320
RW
[7:0]
0x26 SETUPCON6 [15:8]
[7:0]
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
REFBUF6− AINBUF6+
RESERVED
REFBUF7− AINBUF7+
RESERVED
ENHFILT0
REFBUF6+
REFBUF7+
AINBUF6−
AINBUF7−
0x1320
0x1320
0x0500
0x0500
0x0500
0x0500
0x0500
0x0500
0x0500
0x0500
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
BURNOUT_EN6
0x27 SETUPCON7 [15:8]
[7:0]
BURNOUT_EN7
0x28 FILTCON0
0x29 FILTCON1
0x2A FILTCON2
0x2B FILTCON3
0x2C FILTCON4
0x2D FILTCON5
0x2E FILTCON6
0x2F FILTCON7
[15:8] SINC3_MAP0
[7:0] RESERVED
[15:8] SINC3_MAP1
[7:0] RESERVED
[15:8] SINC3_MAP2
[7:0] RESERVED
[15:8] SINC3_MAP3
[7:0] RESERVED
[15:8] SINC3_MAP4
[7:0] RESERVED
[15:8] SINC3_MAP5
[7:0] RESERVED
[15:8] SINC3_MAP6
[7:0] RESERVED
[15:8] SINC3_MAP7
ENHFILTEN0
ENHFILTEN1
ENHFILTEN2
ENHFILTEN3
ENHFILTEN4
ENHFILTEN5
ENHFILTEN6
ENHFILTEN7
ODR0
ODR1
ODR2
ODR3
ODR4
ODR5
ODR6
ODR7
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
ENHFILT1
ENHFILT2
ENHFILT3
ENHFILT4
ENHFILT5
ENHFILT6
ENHFILT7
ORDER1
ORDER2
ORDER3
ORDER4
ORDER5
ORDER6
ORDER7
[7:0]
RESERVED
0x30 OFFSET0
0x31 OFFSET1
0x32 OFFSET2
0x33 OFFSET3
0x34 OFFSET4
0x35 OFFSET5
0x36 OFFSET6
0x37 OFFSET7
0x38 GAIN0
0x39 GAIN1
0x3A GAIN2
0x3B GAIN3
0x3C GAIN4
0x3D GAIN5
0x3E GAIN6
0x3F GAIN7
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
OFFSET0[23:0]
0x800000 RW
0x800000 RW
0x800000 RW
0x800000 RW
0x800000 RW
0x800000 RW
0x800000 RW
0x800000 RW
0x5XXXX0 RW
0x5XXXX0 RW
0x5XXXX0 RW
0x5XXXX0 RW
0x5XXXX0 RW
0x5XXXX0 RW
0x5XXXX0 RW
0x5XXXX0 RW
OFFSET1[23:0]
OFFSET2[23:0]
OFFSET3[23:0]
OFFSET4[23:0]
OFFSET5[23:0]
OFFSET6[23:0]
OFFSET7[23:0]
GAIN0[23:0]
GAIN1[23:0]
GAIN2[23:0]
GAIN3[23:0]
GAIN4[23:0]
GAIN5[23:0]
GAIN6[23:0]
GAIN7[23:0]
Rev. 0 | Page 48 of 64
Data Sheet
AD7175-8
REGISTER DETAILS
COMMUNICATIONS REGISTER
Address: 0x00, Reset: 0x00, Name: COMMS
All access to the on-chip registers must start with a write to the communications register. This write determines what register is accessed
next and whether that operation is a write or a read.
Table 25. Bit Descriptions for COMMS
Bits
Bit Name
Settings
Description
Reset
0x0
Access
W
7
WEN
This bit must be low to begin communications with the ADC.
6
R/W
This bit determines if the command is a read or write operation.
0x0
W
0
1
Write command
Read command
[5:0]
RA
The register address bits determine which register is to be read from or
written to as part of the current communication.
0x00
W
000000 Status register
000001 ADC mode register
000010 Interface mode register
000011 Register checksum register
000100 Data register
000110 GPIO configuration register
000111 ID register
010000 Channel 0 register
010001 Channel 1 register
010010 Channel 2 register
010011 Channel 3 register
010100 Channel 4 register
010101 Channel 5 register
010110 Channel 6 register
010111 Channel 7 register
011000 Channel 8 register
011001 Channel 9 register
011010 Channel 10 register
011011 Channel 11 register
011100 Channel 12 register
011101 Channel 13 register
011110 Channel 14 register
011111 Channel 15 register
100000 Setup Configuration 0 register
100001 Setup Configuration 1 register
100010 Setup Configuration 2 register
100011 Setup Configuration 3 register
100100 Setup Configuration 4 register
100101 Setup Configuration 5 register
100110 Setup Configuration 6 register
100111 Setup Configuration 7 register
101000 Filter Configuration 0 register
101001 Filter Configuration 1 register
101010 Filter Configuration 2 register
101011 Filter Configuration 3 register
101100 Filter Configuration 4 register
101101 Filter Configuration 5 register
101110 Filter Configuration 6 register
101111 Filter Configuration 7 register
Rev. 0 | Page 49 of 64
AD7175-8
Data Sheet
Bits
Bit Name
Settings
Description
Reset
Access
110000 Offset 0 register
110001 Offset 1 register
110010 Offset 2 register
110011 Offset 3 register
110100 Offset 4 register
110101 Offset 5 register
110110 Offset 6 register
110111 Offset 7 register
111000 Gain 0 register
111001 Gain 1 register
111010 Gain 2 register
111011 Gain 3 register
111100 Gain 4 register
111101 Gain 5 register
111110 Gain 6 register
111111 Gain 7 register
Rev. 0 | Page 50 of 64
Data Sheet
AD7175-8
STATUS REGISTER
Address: 0x00, Reset: 0x80, Name: STATUS
The status register is an 8-bit register that contains ADC and serial interface status information. It can optionally be appended to the data
register by setting the DATA_STAT bit in the interface mode register.
Table 26. Bit Descriptions for STATUS
Bits
Bit Name
Settings
Description
Reset
Access
7
RDY
The status of RDY is output to the DOUT/RDY pin whenever CS is low and
a register is not being read. This bit goes low when the ADC has written a
new result to the data register. In ADC calibration modes, this bit goes low
when the ADC has written the calibration result. RDY is brought high
automatically by a read of the data register.
0x1
R
0
1
New data result available
Awaiting new data result
6
ADC_ERROR
This bit by default indicates if an ADC overrange or underrange has
occurred. The ADC result is clamped to 0xFFFFFF for overrange errors and
0x000000 for underrange errors. This bit is updated when the ADC result is
written and is cleared at the next update after removing the overrange or
underrange condition.
0x0
R
0
1
No error
Error
5
4
CRC_ERROR
REG_ERROR
This bit indicates if a CRC error has taken place during a register write. For
register reads, the host microcontroller determines if a CRC error has
occurred. This bit is cleared by a read of this register.
No error
CRC error
0x0
0x0
R
R
0
1
This bit indicates if the content of one of the internal registers has
changed from the value calculated when the register integrity check was
activated. The check is activated by setting the REG_CHECK bit in the
interface mode register. This bit is cleared by clearing the REG_CHECK bit.
0
1
No error
Error
[3:0]
CHANNEL
These bits indicate which channel was active for the ADC conversion
whose result is currently in the data register. This may be different from
the channel currently being converted. The mapping is a direct map from
the channel register; therefore, Channel 0 results in 0x0 and Channel 15
results in 0xF.
0x0
R
0000 Channel 0
0001 Channel 1
0010 Channel 2
0011 Channel 3
0100 Channel 4
0101 Channel 5
0110 Channel 6
0111 Channel 7
1000 Channel 8
1001 Channel 9
1010 Channel 10
1011 Channel 11
1100 Channel 12
1101 Channel 13
1110 Channel 14
1111 Channel 15
Rev. 0 | Page 51 of 64
AD7175-8
Data Sheet
ADC MODE REGISTER
Address: 0x01, Reset: 0xA000, Name: ADCMODE
The ADC mode register controls the operating mode of the ADC and the master clock selection. A write to the ADC mode register resets
the filter and the bits and starts a new conversion or calibration.
RDY
Table 27. Bit Descriptions for ADCMODE
Bits
Bit Name
Settings
Description
Reset
Access
15
REF_EN
Enables internal reference and outputs a buffered 2.5 V to the REFOUT pin. 0x1
RW
0
1
Disabled
Enabled
14
13
HIDE_DELAY
SING_CYC
If a programmable delay is set using the delay bits, this bit allows the
delay to be hidden by absorbing the delay into the conversion time for
selected data rates with the sinc5 + sinc1 filter. See the Delay section for
more information.
Enabled
Disabled
0x0
RW
RW
0
1
This bit can be used when only a single channel is active to set the ADC to 0x1
only output at the settled filter data rate.
0
1
Disabled
Enabled
[12:11] RESERVED
These bits are reserved; set these bits to 0.
0x0
R
[10:8]
DELAY
These bits allow a programmable delay to be added after a channel switch 0x0
to allow the settling of external circuitry before the ADC starts processing
its input.
RW
000 0 µs
001 4 µs
010 16 µs
011 40 µs
100 100 µs
101 200 µs
110 500 µs
111 1 ms
7
RESERVED
MODE
This bit is reserved; set this bit to 0.
0x0
0x0
R
[6:4]
These bits control the operating mode of the ADC. See the Operating
Modes section for more information.
RW
000 Continuous conversion mode
001 Single conversion mode
010 Standby mode
011 Power-down mode
100 Internal offset calibration
110 System offset calibration
111 System gain calibration
[3:2]
[1:0]
CLOCKSEL
RESERVED
These bits are used to select the ADC clock source. Selecting the internal
oscillator also enables the internal oscillator.
00 Internal oscillator
01 Internal oscillator output on the XTAL2/CLKIO pin
10 External clock input on the XTAL2/CLKIO pin
11 External crystal on the XTAL1 and XTAL2/CLKIO pins
These bits are reserved; set these bits to 0.
0x0
0x0
RW
R
Rev. 0 | Page 52 of 64
Data Sheet
AD7175-8
INTERFACE MODE REGISTER
Address: 0x02, Reset: 0x0000, Name: IFMODE
The interface mode register configures various serial interface options.
Table 28. Bit Descriptions for IFMODE
Bits
Bit Name
Settings
Description
Reset
Access
R
[15:13] RESERVED
These bits are reserved; set these bits to 0.
0x0
0x0
12
11
ALT_SYNC
This bit enables a different behavior of the SYNC pin to allow the use
of SYNC as a control for conversions when cycling channels (see the
description of the SYNC_EN bit in the GPIO Configuration Register section
for details).
Disabled
Enabled
RW
0
1
IOSTRENGTH
This bit controls the drive strength of the DOUT/RDY pin. Set this bit when 0x0
reading from the serial interface at high speed with a low IOVDD supply
and moderate capacitance.
RW
0
1
Disabled (default)
Enabled
[10:9]
8
RESERVED
These bits are reserved; set these bits to 0.
0x0
0x0
R
DOUT_RESET
See the DOUT_RESET section for more information.
RW
0
1
Disabled
Enabled
7
6
5
CONTREAD
DATA_STAT
REG_CHECK
This bit enables the continuous read mode of the ADC data register. The
ADC must be configured in continuous conversion mode to use
continuous read mode. For more details, see the Operating Modes
section.
Disabled
Enabled
0x0
RW
RW
RW
0
1
This bit enables the status register to be appended to the data register
when read so that channel and status information are transmitted with
the data. This is the only way to be sure that the channel bits read from
the status register correspond to the data in the data register.
Disabled
Enabled
0x0
0
1
This bit enables a register integrity checker, which can be used to monitor 0x0
any change in the value of the user registers. To use this feature, configure
all other registers as desired with this bit cleared. Then write to this register to
set the REG_CHECK bit to 1. If the contents of any of the registers change,
the REG_ERROR bit is set in the status register. To clear the error, set the
REG_CHECK bit to 0. Neither the interface mode register nor the ADC data
or status registers are included in the registers that are checked. If a
register must have a new value written, this bit must first be cleared;
otherwise, an error is flagged when the new register contents are written.
0
1
Disabled
Enabled
4
RESERVED
CRC_EN
This bit is reserved; set this bit to 0.
0x0
R
[3:2]
These bits enable CRC protection of register reads/writes. CRC increases
the number of bytes in a serial interface transfer by one. See the CRC
Calculation section for more details.
0x00
RW
00 Disabled
01 XOR checksum enabled for register read transactions; register writes still
use CRC with these bits set
10 CRC checksum enabled for read and write transactions
This bit is reserved; set this bit to 0.
1
RESERVED
0x0
R
Rev. 0 | Page 53 of 64
AD7175-8
Data Sheet
Bits
Bit Name
WL16
Settings
Description
Reset
Access
0
This bit changes the ADC data register to 16 bits. The ADC is not reset by a 0x0
write to the interface mode register; therefore, the ADC result is not
rounded to the correct word length immediately after writing to these
bits. The first new ADC result is correct.
RW
0
1
24-bit data
16-bit data
REGISTER CHECK
Address: 0x03, Reset: 0x000000, Name: REGCHECK
The register check register is a 24-bit checksum calculated by exclusively OR'ing the contents of the user registers. The REG_CHECK bit
in the interface mode register must be set for this to operate; otherwise, the register reads 0.
Table 29. Bit Descriptions for REGCHECK
Bits
Bit Name
Settings
Description
Reset
Access
[23:0]
REGISTER_CHECK
This register contains the 24-bit checksum of user registers when the
REG_CHECK bit is set in the interface mode register.
0x000000
R
DATA REGISTER
Address: 0x04, Reset: 0x000000, Name: DATA
The data register contains the ADC conversion result. The encoding is offset binary, or it can be changed to unipolar by the
RDY RDY
output high if it is
BI_UNIPOLARx bits in the setup configuration registers. Reading the data register brings the
bit and the
output is brought high, it is not possible to know if another
RDY
low. The ADC result can be read multiple times; however, because the
ADC result is imminent. After the command to read the ADC register is received, the ADC does not write a new result into the data
register.
Table 30. Bit Descriptions for DATA
Bits
Bit Name
Settings
Description
Reset
Access
[23:0]
DATA
This register contains the ADC conversion result. If DATA_STAT is set in
the interface mode register, the status register is appended to this
register when read, making this a 32-bit register. If WL16 is set in the
interface mode register, this register is reduced to 16 bits.
0x000000
R
Rev. 0 | Page 54 of 64
Data Sheet
AD7175-8
GPIO CONFIGURATION REGISTER
Address: 0x06, Reset: 0x0800, Name: GPIOCON
The GPIO configuration register controls the general-purpose I/O pins of the ADC.
Table 31. Bit Descriptions for GPIOCON
Bits
Bit Name
RESERVED
PDSW
Settings Description
Reset
0x0
Access
R
15
These bits are reserved; set these bits to 0.
14
This bit enables/disables the power-down switch function. Setting the bit allows
the pin to sink current. This function can be used for bridge sensor applications
where the switch controls the power-up/power-down of the bridge.
0x0
RW
13
12
OP_EN2_3
MUX_IO
This bit enables the GPO2 and GPO3 pins. Outputs are referenced between AVDD1 0x0
and AVSS.
RW
RW
This bit allows the ADC to control an external multiplexer, using GPIO0/GPIO1/
GPO2/GPO3 in sync with the internal channel sequencing. The analog input pins
used for a channel can still be selected on a per channel basis. Therefore, it is
possible to have a 16-channel multiplexer in front of each analog input pair
(AIN0/AIN1 to AIN14/AIN15), giving a total of 128 differential channels. However,
only 16 channels at a time can be automatically sequenced. Following the sequence of
16 channels, the user changes the analog input to the next pair of input channels, and
it sequences through the next 16 channels. A delay can be inserted after switching an
external multiplexer (see the delay bits in the ADC Mode Register section).
0x0
11
SYNC_EN
This bit enables the SYNC pin as a synchronization input. When the pin is low, this
holds the ADC and filter in reset until the SYNC pin goes high. An alternative
operation of the SYNC pin is available when the ALT_SYNC bit in the interface
mode register is set. This mode only works when multiple channels are enabled. In
this case, a low on the SYNC pin does not immediately reset the filter/modulator.
Instead, if the SYNC pin is low when the channel is due to be switched, the modulator
and filter are prevented from starting a new conversion. Bringing SYNC high begins
the next conversion. This alternative sync mode allows SYNC to be used while cycling
through channels.
0x1
RW
0
1
Disabled.
Enabled.
[10:9]
ERR_EN
These bits enable the ERROR pin as an error input/output.
0x0
RW
00 Disabled.
01 ERROR is an error input. The (inverted) readback state is OR'ed with other error
sources and is available in the ADC_ERROR bit in the status register. The ERROR pin
state can also be read from the ERR_DAT bit in this register.
10 ERROR is an open-drain error output. The status register error bits are OR'ed,
inverted, and mapped to the ERROR pin. The ERROR pins of multiple devices can
be wired together to a common pull-up resistor so that an error on any device can
be observed.
11 ERROR is a general-purpose output. The status of the pin is controlled by the
ERR_DAT bit in this register. This output is referenced between IOVDD and DGND,
as opposed to the AVDD1 and AVSS levels used by the general-purpose I/O pins.
The ERROR pin has an active pull-up in this case.
8
ERR_DAT
This bit determines the logic level at the ERROR pin if the pin is enabled as a
general-purpose output. This bit reflects the readback status of the pin if the pin is
enabled as an input.
0x0
RW
7
6
5
GP_DATA3
GP_DATA2
IP_EN1
This bit is the write data for GPO3.
0x0
0x0
0x0
W
This bit is the write data for GPO2.
W
This bit turns GPIO1 into an input. Inputs are referenced to AVDD1 or AVSS.
RW
0
1
Disabled.
Enabled.
4
IP_EN0
This bit turns GPIO0 into an input. Inputs are referenced to AVDD1 or AVSS.
0x0
RW
0
1
Disabled.
Enabled.
Rev. 0 | Page 55 of 64
AD7175-8
Data Sheet
Bits
Bit Name
Settings Description
This bit turns GPIO1 into an output. Outputs are referenced between AVDD1 and AVSS. 0x0
Disabled.
Reset
Access
3
OP_EN1
RW
0
1
Enabled.
2
OP_EN0
This bit turns GPIO0 into an output. Outputs are referenced between AVDD1 and AVSS. 0x0
RW
0
1
Disabled.
Enabled.
1
0
GP_DATA1
GP_DATA0
This bit is the readback or write data for GPIO1.
This bit is the readback or write data for GPIO0.
0x0
0x0
RW
RW
ID REGISTER
Address: 0x07, Reset: 0x3CDx, Name: ID
The ID register returns a 16-bit ID. For the AD7175-8, this ID is 0x3CDx.
Table 32. Bit Descriptions for ID
Bits
Bit Name
Settings
Description
Reset
Access
[15:0]
ID
The ID register returns a 16-bit ID code that is specific to the ADC.
0x3CDx
R
0x3CDx AD7175-8
CHANNEL REGISTER 0
Address: 0x10, Reset: 0x8001, Name: CH0
The channel registers are 16-bit registers used to select which channels are currently active, which inputs are selected for each channel,
and which setup is used to configure the ADC for that channel.
Table 33. Bit Descriptions for CH0
Bits
Bit Name
Settings
Description
Reset
Access
15
CH_EN0
This bit enables Channel 0. If more than one channel is enabled, the ADC 0x1
automatically sequences between them.
RW
0
1
Disabled
Enabled (default)
[14:12] SETUP_SEL0
These bits identify which of the eight setups is used to configure the
ADC for this channel. A setup comprises a set of four registers: setup
configuration register, filter configuration register, offset register, and gain
register. All channels can use the same setup, in which case the same 3-bit
value must be written to these bits on all active channels, or up to eight
channels can be configured differently.
0x0
RW
000 Setup 0
001 Setup 1
010 Setup 2
011 Setup 3
100 Setup 4
101 Setup 5
110 Setup 6
111 Setup 7
[11:10] RESERVED
[9:5] AINPOS0
These bits are reserved; set these bits to 0.
0x0
0x0
R
These bits select which input is connected to the positive input of the
ADC for this channel.
RW
00000 AIN0 (default)
00001 AIN1
00010 AIN2
00011 AIN3
00100 AIN4
00101 AIN5
00110 AIN6
00111 AIN7
Rev. 0 | Page 56 of 64
Data Sheet
AD7175-8
Bits
Bit Name
Settings
Description
Reset
Access
01000 AIN8
01001 AIN9
01010 AIN10
01011 AIN11
01100 AIN12
01101 AIN13
01110 AIN14
01111 AIN15
10000 AIN16
10001 Temperature sensor+
10010 Temperature sensor−
10011 ((AVDD1 − AVSS)/5)+ (analog input buffers must be enabled)
10100 ((AVDD1 − AVSS)/5)− (analog input buffers must be enabled)
10101 REF+
10110 REF−
[4:0]
AINNEG0
These bits select which input is connected to the negative input of the
ADC for this channel.
0x1
RW
00000 AIN0
00001 AIN1 (default)
00010 AIN2
00011 AIN3
00100 AIN4
00101 AIN5
00110 AIN6
00111 AIN7
01000 AIN8
01001 AIN9
01010 AIN10
01011 AIN11
01100 AIN12
01101 AIN13
01110 AIN14
01111 AIN15
10000 AIN16
10001 Temperature sensor+
10010 Temperature sensor−
10011 ((AVDD1 − AVSS)/5)+
10100 ((AVDD1 − AVSS)/5)−
10101 REF+
10110 REF−
Rev. 0 | Page 57 of 64
AD7175-8
Data Sheet
CHANNEL REGISTER 1 TO CHANNEL REGISTER 15
Address: 0x11 to 0x1F, Reset: 0x0001, Name: CH1 to CH7
The remaining 15 channel registers share the same layout as Channel Register 0.
Table 34. CH1 to CH15 Register Map
Reg.
0x11
Name
CH1
Bits
[15:8]
[7:0]
Bit 7
CH_EN1
Bit 6
Bit 5
SETUP_SEL1
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
0x0001
RW
RW
RESERVED
AINNEG1
RESERVED
AINNEG2
RESERVED
AINNEG3
RESERVED
AINNEG4
RESERVED
AINNEG5
RESERVED
AINNEG6
RESERVED
AINNEG7
RESERVED
AINNEG8
RESERVED
AINNEG9
RESERVED
AINNEG10
RESERVED
AINNEG11
RESERVED
AINNEG12
RESERVED
AINNEG13
RESERVED
AINNEG14
RESERVED
AINNEG15
AINPOS1[4:3]
AINPOS2[4:3]
AINPOS3[4:3]
AINPOS4[4:3]
AINPOS5[4:3]
AINPOS6[4:3]
AINPOS7[4:3]
AINPOS8[4:3]
AINPOS9[4:3]
AINPOS10[4:3]
AINPOS11[4:3]
AINPOS12[4:3]
AINPOS13[4:3]
AINPOS14[4:3]
AINPOS15[4:3]
AINPOS1[2:0]
AINPOS2[2:0]
AINPOS3[2:0]
AINPOS4[2:0]
AINPOS5[2:0]
AINPOS6[2:0]
AINPOS7[2:0]
AINPOS8[2:0]
AINPOS9[2:0]
AINPOS10[2:0]
AINPOS11[2:0]
AINPOS12[2:0]
AINPOS13[2:0]
AINPOS14[2:0]
AINPOS15[2:0]
0x12
0x13
0x14
0x15
0x16
0x17
0x18
0x19
0x1A
0x1B
0x1C
0x1D
0x1E
0x1F
CH2
[15:8]
[7:0]
CH_EN2
CH_EN3
CH_EN4
CH_EN5
CH_EN6
CH_EN7
CH_EN8
CH_EN9
CH_EN10
CH_EN11
CH_EN12
CH_EN13
CH_EN14
CH_EN15
SETUP_SEL2
SETUP_SEL3
SETUP_SEL4
SETUP_SEL5
SETUP_SEL6
SETUP_SEL7
SETUP_SEL8
SETUP_SEL9
SETUP_SEL10
SETUP_SEL11
SETUP_SEL12
SETUP_SEL13
SETUP_SEL14
SETUP_SEL15
0x0001
0x0001
0x0001
0x0001
0x0001
0x0001
0x0001
0x0001
0x0001
0x0001
0x0001
0x0001
0x0001
0x0001
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
CH3
[15:8]
[7:0]
CH4
[15:8]
[7:0]
CH5
[15:8]
[7:0]
CH6
[15:8]
[7:0]
CH7
[15:8]
[7:0]
CH8
[15:8]
[7:0]
CH9
[15:8]
[7:0]
CH10
CH11
CH12
CH13
CH14
CH15
[15:8]
[7:0]
[15:8]
[7:0]
[15:8]
[7:0]
[15:8]
[7:0]
[15:8]
[7:0]
[15:8]
[7:0]
Rev. 0 | Page 58 of 64
Data Sheet
AD7175-8
SETUP CONFIGURATION REGISTER 0
Address: 0x20, Reset: 0x1320, Name: SETUPCON0
The setup configuration registers are 16-bit registers that configure the reference selection, input buffers, and output coding of the ADC.
Table 35. Bit Descriptions for SETUPCON0
Bits
Bit Name
Settings
Description
Reset
0x0
Access
R
[15:13] RESERVED
These bits are reserved; set these bits to 0.
This bit sets the output coding of the ADC for Setup 0.
Unipolar coded output
Bipolar coded output (offset binary)
This bit enables or disables the REF+ input buffer.
REF+ buffer disabled
12
11
10
9
BI_UNIPOLAR0
0x1
RW
0
1
REFBUF0+
REFBUF0−
AINBUF0+
AINBUF0−
BURNOUT_EN0
0x0
0x0
0x1
0x1
0x00
RW
RW
RW
RW
R
0
1
REF+ buffer enabled
This bit enables or disables the REF− input buffer.
REF− buffer disabled
REF− buffer enabled
0
1
This bit enables or disables the AIN+ input buffer.
AIN+ buffer disabled
AIN+ buffer enabled
0
1
8
This bit enables or disables the AIN− input buffer.
AIN− buffer disabled
AIN− buffer enabled
0
1
7
This bit enables a 10 µA current source on the positive analog input
selected and a 10 µA current sink on the negative analog input selected.
The burnout currents are useful in diagnosis of an open wire, whereby the
ADC result goes to full scale. Enabling the burnout currents during
measurement results in an offset voltage on the ADC. This means the
strategy for diagnosing an open wire operates best by turning on the
burnout currents at intervals, before or after precision measurements.
6
RESERVED
REF_SEL0
These bits are reserved; set these bits to 0.
0x00
0x2
R
[5:4]
These bits allow the user to select the reference source for ADC
conversion on Setup 0.
RW
00 External reference.
01 External Reference 2 supplied to AIN1/REF2+ and AIN0/REF2− pins.
10 Internal 2.5 V reference. This must also be enabled in the ADC mode register.
11 AVDD1 − AVSS. This can be used to as a diagnostic to validate other
reference values.
[3:0]
RESERVED
These bits are reserved; set these bits to 0.
0x0
R
Rev. 0 | Page 59 of 64
AD7175-8
Data Sheet
SETUP CONFIGURATION REGISTER 1 TO SETUP CONFIGURATION REGISTER 7
Address: 0x21 to 0x27, Reset: 0x1320, Name: SETUPCON1 to SETUPCON7
The remaining seven setup configuration registers share the same layout as Setup Configuration Register 0.
Table 36. SETUPCON1 to SETUPCON7 Register Map
Reg.
Name
Bits
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
AINBUF1+
Bit 0
Reset
RW
RW
0x21
SETUPCON1 [15:8]
[7:0]
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
BI_UNIPOLAR1
REFBUF1+
REFBUF1−
AINBUF1− 0x1320
AINBUF2− 0x1320
AINBUF3− 0x1320
AINBUF4− 0x1320
AINBUF5− 0x1320
AINBUF6− 0x1320
AINBUF7− 0x1320
BURNOUT_EN1
BURNOUT_EN2
BURNOUT_EN3
BURNOUT_EN4
BURNOUT_EN5
BURNOUT_EN6
BURNOUT_EN7
REF_SEL1
BI_UNIPOLAR2
REF_SEL2
BI_UNIPOLAR3
REF_SEL3
BI_UNIPOLAR4
REF_SEL4
BI_UNIPOLAR5
REF_SEL5
BI_UNIPOLAR6
REF_SEL6
BI_UNIPOLAR7
REF_SEL7
RESERVED
REFBUF2− AINBUF2+
RESERVED
REFBUF3− AINBUF3+
RESERVED
REFBUF4− AINBUF4+
RESERVED
REFBUF5− AINBUF5+
RESERVED
REFBUF6− AINBUF6+
RESERVED
REFBUF7− AINBUF7+
RESERVED
0x22
0x23
0x24
0x25
0x26
0x27
SETUPCON2 [15:8]
[7:0]
REFBUF2+
REFBUF3+
REFBUF4+
REFBUF5+
REFBUF6+
REFBUF7+
RW
RW
RW
RW
RW
RW
SETUPCON3 [15:8]
[7:0]
SETUPCON4 [15:8]
[7:0]
SETUPCON5 [15:8]
[7:0]
SETUPCON6 [15:8]
[7:0]
SETUPCON7 [15:8]
[7:0]
Rev. 0 | Page 60 of 64
Data Sheet
AD7175-8
FILTER CONFIGURATION REGISTER 0
Address: 0x28, Reset: 0x0500, Name: FILTCON0
The filter configuration registers are 16-bit registers that configure the ADC data rate and filter options. Writing to any of these registers
resets any active ADC conversion and restarts converting at the first channel in the sequence.
Table 37. Bit Descriptions for FILTCON0
Bits
Bit Name
Settings
Description
Reset
Access
15
SINC3_MAP0
If this bit is set, the mapping of the filter register changes to directly
program the decimation rate of the sinc3 filter for Setup 0. All other
options are eliminated. This allows fine tuning of the output data rate and
filter notch for rejection of specific frequencies. The data rate when on a
single channel equals fMOD/(32 × FILTCON0[14:0]).
0x0
RW
[14:12] RESERVED
These bits are reserved; set these bits to 0.
0x0
0x0
R
11
ENHFILTEN0
This bit enables various postfilters for enhanced 50 Hz/60 Hz rejection for
Setup 0. The ORDER0 bits must be set to 00 to select the sinc5 + sinc1
filter for this to work.
RW
0
1
Disabled
Enabled
[10:8]
ENHFILT0
These bits select between various postfilters for enhanced 50 Hz/60 Hz
rejection for Setup 0.
0x5
RW
010 27 SPS, 47 dB rejection, 36.7 ms settling
011 25 SPS, 62 dB rejection, 40 ms settling
101 20 SPS, 86 dB rejection, 50 ms settling
110 16.67 SPS, 92 dB rejection, 60 ms settling
This bit is reserved; set this bit to 0.
7
RESERVED
ORDER0
0x0
0x0
R
[6:5]
These bits control the order of the digital filter that processes the
modulator data for Setup 0.
RW
00 Sinc5 + sinc1 (default)
11 Sinc3
[4:0]
ODR0
These bits control the output data rate of the ADC and, therefore, the
settling time and noise for Setup 0. Rates shown are for the sinc5 + sinc 1
filter. See Table 19 to Table 22.
0x0
RW
00000 250,000
00001 125,000
00010 62,500
00011 50,000
00100 31,250
00101 25,000
00110 15,625
00111 10,000
01000 5000
01001 2500
01010 1000
01011 500
01100 397.5
01101 200
01110 100
01111 59.92
10000 49.96
10001 20
10010 16.66
10011 10
10100
5
Rev. 0 | Page 61 of 64
AD7175-8
Data Sheet
FILTER CONFIGURATION REGISTER 1 TO FILTER CONFIGURATION REGISTER 7
Address: 0x29 to 0x2F, Reset: 0x0500, Name: FILTCON1 to FILTCON7
The remaining seven filter configuration registers share the same layout as Filter Configuration Register 0.
Table 38. FILTCON1 to FILTCON7 Register Map
Reg.
Name
Bits
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
ODR1
Bit 1
Bit 0
Reset
RW
0x29
FILTCON1
[15:8]
[7:0]
SINC3_MAP1
RESERVED
SINC3_MAP2
RESERVED
SINC3_MAP3
RESERVED
SINC3_MAP4
RESERVED
SINC3_MAP5
RESERVED
SINC3_MAP6
RESERVED
SINC3_MAP7
RESERVED
RESERVED
ENHFILTEN1
ENHFILT1
0x0500
RW
ORDER1
RESERVED
ORDER2
RESERVED
ORDER3
RESERVED
ORDER4
RESERVED
ORDER5
RESERVED
ORDER6
RESERVED
ORDER7
0x2A
0x2B
0x2C
0x2D
0x2E
0x2F
FILTCON2
FILTCON3
FILTCON4
FILTCON5
FILTCON6
FILTCON7
[15:8]
[7:0]
ENHFILTEN2
ENHFILTEN3
ENHFILTEN4
ENHFILTEN5
ENHFILTEN6
ENHFILTEN7
ENHFILT2
ENHFILT3
ENHFILT4
ENHFILT5
ENHFILT6
ENHFILT7
0x0500
0x0500
0x0500
0x0500
0x0500
0x0500
RW
RW
RW
RW
RW
RW
ODR2
ODR3
ODR4
ODR5
ODR6
ODR7
[15:8]
[7:0]
[15:8]
[7:0]
[15:8]
[7:0]
[15:8]
[7:0]
[15:8]
[7:0]
OFFSET REGISTER 0
Address: 0x30, Reset: 0x800000, Name: OFFSET0
The offset (zero-scale) registers are 24-bit registers that can be used to compensate for any offset error in the ADC or in the system.
Table 39. Bit Descriptions for OFFSET0
Bits
Bit Name
Settings
Description
Reset
Access
[23:0]
OFFSET0
Offset calibration coefficient for Setup 0.
0x800000 RW
OFFSET REGISTER 1 TO OFFSET REGISTER 7
Address: 0x31 to 0x37, Reset: 0x800000, Name: OFFSET1 to OFFSET7
The remaining seven offset registers share the same layout as Offset Register 0.
Table 40. OFFSET1 to OFFSET7 Register Map
Reg.
0x30
0x31
0x32
0x33
0x34
0x35
0x36
0x37
Name
Bits
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
RW
OFFSET0
OFFSET1
OFFSET2
OFFSET3
OFFSET4
OFFSET5
OFFSET6
OFFSET7
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
OFFSET0[23:0]
OFFSET1[23:0]
OFFSET2[23:0]
OFFSET3[23:0]
OFFSET4[23:0]
OFFSET5[23:0]
OFFSET6[23:0]
OFFSET7[23:0]
0x800000
0x800000
0x800000
0x800000
0x800000
0x800000
0x800000
0x800000
RW
RW
RW
RW
RW
RW
RW
RW
GAIN REGISTER 0
Address: 0x38, Reset: 0x5XXXX0, Name: GAIN0
The gain (full-scale) registers are 24-bit registers that can be used to compensate for any gain error in the ADC or in the system.
Table 41. Bit Descriptions for GAIN0
Bits
Bit Name
Settings
Description
Reset
Access
[23:0]
GAIN0
Gain calibration coefficient for Setup 0.
0x5XXXX0 RW
Rev. 0 | Page 62 of 64
Data Sheet
AD7175-8
GAIN REGISTER 1 TO GAIN REGISTER 7
Address: 0x39 to 0x3F, Reset: 0x5XXXX0, Name: GAIN1 to GAIN7
The remaining seven gain registers share the same layout as Gain Register 0.
Table 42. GAIN1 to GAIN7 Register Map
Reg.
0x38
0x39
0x3A
0x3B
0x3C
0x3D
0x3E
0x3F
Name
GAIN0
GAIN1
GAIN2
GAIN3
GAIN4
GAIN5
GAIN6
GAIN7
Bits
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
GAIN0[23:0]
GAIN1[23:0]
GAIN2[23:0]
GAIN3[23:0]
GAIN4[23:0]
GAIN5[23:0]
GAIN6[23:0]
GAIN7[23:0]
Bit 2
Bit 1
Bit 0
Reset
RW
RW
RW
RW
RW
RW
RW
RW
RW
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
0x5XXXX0
0x5XXXX0
0x5XXXX0
0x5XXXX0
0x5XXXX0
0x5XXXX0
0x5XXXX0
0x5XXXX0
Rev. 0 | Page 63 of 64
AD7175-8
Data Sheet
OUTLINE DIMENSIONS
6.10
6.00 SQ
5.90
0.30
0.25
0.18
PIN 1
INDICATOR
PIN 1
INDICATOR
31
30
40
1
0.50
BSC
4.05
3.90 SQ
3.75
EXPOSED
PAD
21
20
10
11
0.45
0.40
0.35
0.25 MIN
TOP VIEW
BOTTOM VIEW
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
0.80
0.75
0.70
0.05 MAX
0.02 NOM
SECTION OF THIS DATA SHEET.
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-220-WJJD.
Figure 72. 40-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
6 mm × 6 mm Body, Very Very Thin Quad
(CP-40-14)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
Temperature Range
Package Description
Package Option
AD7175-8BCPZ
AD7175-8BCPZ-RL
AD7175-8BCPZ-RL7
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
40-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
40-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
40-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
CP-40-14
CP-40-14
CP-40-14
1 Z = RoHS Compliant Part.
©2015 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D12911-0-10/15(0)
Rev. 0 | Page 64 of 64
相关型号:
![](http://pdffile.icpdf.com/pdf2/p00209/img/page/AD7176_1179604_files/AD7176_1179604_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00209/img/page/AD7176_1179604_files/AD7176_1179604_2.jpg)
AD7176-2
The AD7176-2 is a fast settling, highly accurate, high resolution, multiplexed Σ-Πanalog-to-digital converter (ADC) for low band-width input signals.
ADI
![](http://pdffile.icpdf.com/pdf2/p00209/img/page/AD7176_1179604_files/AD7176_1179604_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00209/img/page/AD7176_1179604_files/AD7176_1179604_2.jpg)
AD7176-2BRUZ
The AD7176-2 is a fast settling, highly accurate, high resolution, multiplexed Σ-Πanalog-to-digital converter (ADC) for low band-width input signals.
ADI
![](http://pdffile.icpdf.com/pdf2/p00209/img/page/AD7176_1179604_files/AD7176_1179604_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00209/img/page/AD7176_1179604_files/AD7176_1179604_2.jpg)
AD7176-2BRUZ-RL
The AD7176-2 is a fast settling, highly accurate, high resolution, multiplexed Σ-Πanalog-to-digital converter (ADC) for low band-width input signals.
ADI
![](http://pdffile.icpdf.com/pdf2/p00305/img/page/AD7177-2BRUZ_1842002_files/AD7177-2BRUZ_1842002_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00305/img/page/AD7177-2BRUZ_1842002_files/AD7177-2BRUZ_1842002_2.jpg)
AD7177-2BRUZ
32-Bit, 10 kSPS, Sigma-Delta ADC with 100 µs Settling and True Rail-to-Rail Buffers
ADI
![](http://pdffile.icpdf.com/pdf2/p00305/img/page/AD7177-2BRUZ_1842002_files/AD7177-2BRUZ_1842002_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00305/img/page/AD7177-2BRUZ_1842002_files/AD7177-2BRUZ_1842002_2.jpg)
AD7177-2BRUZ-RL7
32-Bit, 10 kSPS, Sigma-Delta ADC with 100 µs Settling and True Rail-to-Rail Buffers
ADI
©2020 ICPDF网 联系我们和版权申明