AD7656A-1BSTZ [ADI]
250 kSPS, 6-Channel, Simultaneous Sampling, Bipolar, 16-Bit ADC;
| 型号： | AD7656A-1BSTZ |
| 厂家： | 
ADI |
| 描述： | 250 kSPS, 6-Channel, Simultaneous Sampling, Bipolar, 16-Bit ADC 转换器 |
| 文件： | 总29页 (文件大小：658K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
250 kSPS, 6-Channel, Simultaneous
Sampling, Bipolar, 16-Bit ADC
Data Sheet
AD7656A-1
FEATURES
FUNCTIONAL BLOCK DIAGRAM
V
CONVST A CONVST B CONVST C AV
DV
CC CC
DD
Pin and software compatible with the AD7656A featuring
reduced decoupling requirements
6 independent analog-to-digital converters (ADCs)
True bipolar analog inputs
Pin-/software-selectable ranges: 10 V or 5 V
Fast throughput rate: 250 kSPS
iCMOS process technology
Low power: 140 mW at 250 kSPS with 5 V supplies
High noise performance with wide bandwidth
88 dB SNR at 10 kHz input frequency
On-chip reference and reference buffers
High speed parallel, serial, and daisy-chain interface modes
High speed serial interface
Serial peripheral interface (SPI)/QSPI™/MICROWIRE®/DSP
compatible
Power-down mode: 315 µW maximum
64-lead LQFP
CS
CLK
OSC
REF
SER/PAR SEL
CONTROL
LOGIC
V
DRIVE
STBY
BUF
OUTPUT
DRIVERS
DB8/DOUT A
16-BIT SAR
T/H
V1
V2
V3
V4
V5
V6
DB6/SCLK
T/H
T/H
T/H
T/H
T/H
16-BIT SAR
16-BIT SAR
16-BIT SAR
16-BIT SAR
16-BIT SAR
OUTPUT
DRIVERS
DB9/DOUT B
BUF
BUF
OUTPUT
DRIVERS
DB10/DOUT C
DATA/
CONTROL
LINES
OUTPUT
DRIVERS
RD
WR/REF
EN/DIS
Built-in power supply sequencing (PSS) robustness solution
AD7656A-1
APPLICATIONS
V
AGND
DGND
SS
Power line monitoring and measuring systems
Instrumentation and control systems
Multiaxis positioning systems
Figure 1.
The conversion process and data acquisition are controlled
using the CONVST x signals and an internal oscillator. Three
CONVST x pins (CONVST A, CONVST B, and CONVST C)
allow independent, simultaneous sampling of the three ADC
pairs. The AD7656A-1 has a high speed parallel and serial
interface, allowing the device to interface with microprocessors
or digital signal processors (DSPs). In serial interface mode, the
AD7656A-1 has a daisy-chain feature that allows multiple
ADCs to connect to a single serial interface. The AD7656A-1
can accommodate true bipolar input signals in the 4 × VREF
range and the 2 × VREF range. The AD7656A-1 also contains
an on-chip 2.5 V reference.
GENERAL DESCRIPTION
The AD7656A-11 is a reduced decoupling pin- and software-
compatible version of AD7656A. The AD7656A-1 contains six
16-bit, fast, low power successive approximation ADCs in a
package designed on the iCMOS® process (industrial CMOS).
iCMOS is a process combining high voltage silicon with submicron
CMOS and complementary bipolar technologies. It enables the
development of a wide range of high performance analog ICs,
capable of 33 V operation in a footprint that no previous
generation of high voltage devices could achieve. Unlike analog
ICs using conventional CMOS processes, iCMOS components
can accept bipolar input signals while providing increased
performance, which dramatically reduces power consumption
and package size.
Multifunction pin names may be referenced by their relevant
function only.
The AD7656A-1 features throughput rates of to 250 kSPS. It
contains wide bandwidth (4.5 MHz), track-and-hold amplifiers
that can handle input frequencies up to 4.5 MHz.
PRODUCT HIGHLIGHTS
1. Six 16-bit, 250 kSPS ADCs on board.
2. Six true bipolar, high impedance analog inputs.
3. High speed parallel and serial interfaces.
4. Reduced decoupling requirements and reduced bill of
materials cost compared with the AD7656A.
1 Protected by U.S. Patent No. 6,731,232.
Rev. 0
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rightsof third parties that may result fromits use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks andregisteredtrademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Technical Support
©2013 Analog Devices, Inc. All rights reserved.
www.analog.com
AD7656A-1* PRODUCT PAGE QUICK LINKS
Last Content Update: 02/23/2017
COMPARABLE PARTS
View a parametric search of comparable parts.
REFERENCE MATERIALS
Technical Articles
• MS-2210: Designing Power Supplies for High Speed ADC
DOCUMENTATION
DESIGN RESOURCES
• AD7656A-1 Material Declaration
• PCN-PDN Information
Application Notes
• AN-893: Configuring the AD7656/AD7657/AD7658 for
Serial and Daisy-Chain Interface Modes of Operation
• AN-931: Understanding PulSAR ADC Support Circuitry
• Quality And Reliability
Data Sheet
• Symbols and Footprints
• AD7656A-1: 250 kSPS, 6-Channel, Simultaneous Sampling,
Bipolar, 16-Bit ADC Data Sheet
DISCUSSIONS
View all AD7656A-1 EngineerZone Discussions.
User Guides
• UG-417: Evaluating the AD7656-1/AD7657-1/AD7658-1,
250 kSPS, 6-Channel, Simultaneous Sampling, Bipolar 16-/
14-/12-Bit ADCs
SAMPLE AND BUY
Visit the product page to see pricing options.
SOFTWARE AND SYSTEMS REQUIREMENTS
• AD7656-1 FMC-SDP Interposer & Evaluation Board / Xilinx
TECHNICAL SUPPORT
Submit a technical question or find your regional support
number.
KC705 Reference Design
• BeMicro FPGA Project for AD7656-1 with Nios driver
DOCUMENT FEEDBACK
Submit feedback for this data sheet.
This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not
trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified.
AD7656A-1
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Theory of Operation ...................................................................... 15
Converter Details ....................................................................... 15
ADC Transfer Function............................................................. 16
Internal/External Reference...................................................... 16
Typical Connection Diagram ................................................... 16
Driving the Analog Inputs ........................................................ 17
Interface Options........................................................................ 17
Software Selection of ADCs...................................................... 19
Serial Read Operation................................................................ 21
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description......................................................................... 1
Product Highlights ........................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Timing Specifications .................................................................. 5
Absolute Maximum Ratings............................................................ 6
Power Supply Sequencing ........................................................... 6
Thermal Resistance ...................................................................... 6
ESD Caution.................................................................................. 6
Pin Configuration and Function Descriptions............................. 7
Typical Performance Characteristics ........................................... 10
Terminology .................................................................................... 13
PAR
/SEL = 1)............. 22
Daisy-Chain Mode (DCEN = 1, SER/
Application Hints ........................................................................... 24
Layout .......................................................................................... 24
Outline Dimensions....................................................................... 25
Ordering Guide .......................................................................... 25
REVISION HISTORY
12/13—Revision 0: Initial Version
Rev. 0 | Page 2 of 28
Data Sheet
AD7656A-1
SPECIFICATIONS
VREF = 2.5 V internal/external, AVCC = 4.75 V to 5.25 V, DVCC = 4.75 V to 5.25 V, and VDRIVE = 2.7 V to 5.25 V. For the 4 × VREF range,
V
DD = 11 V to 16.5 V, and VSS = −11 V to −16.5 V. For the 2 × VREF range, VDD = 6 V to 16.5 V, and VSS = −6 V to −16.5 V. fSAMPLE =
250 kSPS, and TA = TMIN to TMAX, unless otherwise noted.
Table 1.
Parameter
Min
Typ
Max
Unit
Test Conditions/Comments
DYNAMIC PERFORMANCE
Signal-to-Noise + Distortion (SINAD)1
Signal-to-Noise Ratio (SNR)1
Total Harmonic Distortion (THD)1
fIN = 10 kHz sine wave
88
88
dB
dB
dB
dB
dB
−90
−105
−100
VDD/VSS = 6 V to 16.5 V
fa = 10.5 kHz, fb = 9.5 kHz
Peak Harmonic or Spurious Noise (SFDR)1
Intermodulation Distortion (IMD)1
Second-Order Terms
−112
−107
dB
dB
Third-Order Terms
Aperture Delay
Aperture Delay Matching
Aperture Jitter
10
4
ns
ns
ps
35
Channel-to-Channel Isolation1
Full-Power Bandwidth
−100
4.5
2.2
dB
MHz
MHz
fIN on unselected channels up to 100 kHz
At −3 dB
At −0.1 dB
DC ACCURACY
Resolution
No Missing Codes
Integral Nonlinearity1
16
15
Bits
Bits
LSB
3
1
LSB
Positive Full-Scale Error1
Positive Full-Scale Error Matching1
Bipolar Zero-Scale Error1
Bipolar Zero-Scale Error Matching1
Negative Full-Scale Error1
Negative Full-Scale Error Matching1
ANALOG INPUT
0.381
0.8
0.35
0.048
0.038
0.8
% FSR
% FSR
% FSR
% FSR
% FSR
% FSR
0.0137%
0.381
0.35
See Table 6 for minimum VDD/VSS for each
range
Input Voltage Ranges
−4 × VREF
−2 × VREF
+4 × VREF
+2 × VREF
1
V
V
µA
pF
pF
RNGx bits or RANGE pin = 0
RNGx bits or RANGE pin = 1
DC Leakage Current
Input Capacitance2
10
14
4 × VREF range when in track mode
2 × VREF range when in track mode
REFERENCE INPUT/OUTPUT
Reference Input Voltage Range
DC Leakage Current
2.5
3
1
V
µA
pF
Input Capacitance2
18.5
150
6
REFEN/DIS = 13
1000 hours
Reference Output Voltage
Long-Term Stability
Reference Temperature Coefficient
2.49
2.51
25
V
ppm
ppm/°C
ppm/°C
Rev. 0 | Page 3 of 28
AD7656A-1
Data Sheet
Parameter
Min
Typ
Max
Unit
Test Conditions/Comments
LOGIC INPUTS
Input High Voltage (VINH
)
0.7 × VDRIVE
V
Input Low Voltage (VINL
Input Current (IIN)
)
0.3 × VDRIVE
10
10
V
µA
pF
Typically 10 nA, VIN = 0 V or VDRIVE
Input Capacitance (CIN)2
LOGIC OUTPUTS
Output High Voltage (VOH)
Output Low Voltage (VOL)
Floating-State Leakage Current
Floating-State Output Capacitance2
Output Coding
VDRIVE − 0.2
V
V
µA
pF
ISOURCE = 200 µA
ISINK = 200 µA
0.2
10
10
Twos complement
CONVERSION RATE
Conversion Time
3.1
µs
Track-and-Hold Acquisition Time1, 2
Throughput Rate
POWER REQUIREMENTS
VDD Range
VSS Range
AVCC
550
250
ns
kSPS
Parallel interface mode only
6
−6
4.75
4.75
2.7
16.5
−16.5
5.25
5.25
5.25
V
V
V
V
V
For the 4 × VREF range, VDD = 11 V to 16.5 V
For the 4 × VREF range, VSS= −11 V to −16.5 V
DVCC
VDRIVE
4
ITOTAL
Digital inputs = 0 V or VDRIVE
Normal Mode (Static)
18
26
mA
mA
AVCC = DVCC = VDRIVE = 5.25 V, VDD = 16.5 V,
VSS = −16.5 V
fSAMPLE = 250 kSPS, AVCC = DVCC = VDRIVE = 5.25 V,
Normal Mode (Operational)
V
DD = 16.5 V, VSS = −16.5 V
ISS (Operational)
IDD (Operational)
Partial Power-Down Mode
0.25
0.25
7
mA
mA
mA
VSS = −16.5 V, fSAMPLE = 250 kSPS
VDD = 16.5 V, fSAMPLE = 250 kSPS
AVCC = DVCC = VDRIVE = 5.25 V, VDD = 16.5 V,
VSS = −16.5 V
Full Power-Down Mode (STBY Pin)
Power Dissipation
60
µA
SCLK on or off, AVCC = DVCC = VDRIVE = 5.25 V,
V
DD = 16.5 V, VSS = −16.5 V
AVCC = DVCC = VDRIVE = 5.25 V, VDD = 16.5 V,
VSS = −16.5 V
Normal Mode (Static)
94
140
40
mW
mW
mW
µW
Normal Mode (Operational)
Partial Power-Down Mode
Full Power-Down Mode (STBY Pin)
fSAMPLE = 250 kSPS
315
1 See the Terminology section.
2 Sample tested during initial release to ensure compliance.
3 Multifunction pin names may be referenced by their relevant function only.
4 Includes IAVCC, IVDD, IVSS, IVDRIVE, and IDVCC
.
Rev. 0 | Page 4 of 28
Data Sheet
AD7656A-1
TIMING SPECIFICATIONS
AVCC and DVCC = 4.75 V to 5.25 V, VDRIVE = 2.7 V to 5.25 V, VREF = 2.5 V internal/external, TA = TMIN to TMAX, unless otherwise noted. For the
4 × VREF range, VDD = 11 V to 16.5 V, and VSS = −11 V to −16.5 V. For the 2 × VREF range, VDD = 6 V to 16.5 V, and VSS = −6 V to
−16.5 V. Sample tested during initial release to ensure compliance. All input signals are specified with tR = tF = 5 ns (10% to 90% of VDD) and
timed from a voltage level of 1.6 V.
Table 2.
Limit at TMIN, TMAX
Parameter
VDRIVE < 4.75 V VDRIVE = 4.75 V to 5.25 V
Unit
Description1
PARALLEL INTERFACE MODE
tCONV
tQUIET
3
150
3
150
µs typ
ns min
Conversion time, internal clock
Minimum quiet time required between bus
relinquish and start of next conversion
tACQ
t10
t1
550
25
60
2
550
25
60
2
ns min
ns min
ns max
ms max
Acquisition time
Minimum CONVST x low pulse
CONVST x high to BUSY high
STBY rising edge to CONVST x rising edge, not
shown in figures
tWAKE-UP
25
25
µs max
Partial power-down mode
PARALLEL READ OPERATION
t2
0
0
ns min
ns min
ns min
ns min
ns max
ns min
ns max
ns min
BUSY to RD delay
t3
0
0
CS to RD setup time
t4
0
0
CS to RD hold time
t5
45
45
10
12
6
36
36
10
12
6
RD pulse width
t6
Data access time after RD falling edge
Data hold time after RD rising edge
Bus relinquish time after RD rising edge
Minimum time between reads
t7
t8
t9
PARALLEL WRITE OPERATION
t11
t12
t13
t14
t15
15
0
15
0
ns min
ns min
ns min
ns min
ns min
WR pulse width
CS to WR setup time
5
5
CS to WR hold time
5
5
Data setup time before WR rising edge
Data hold after WR rising edge
5
5
SERIAL INTERFACE MODE
fSCLK
t16
18
12
22
18
12
22
MHz max Frequency of serial read clock
ns max
ns max
Delay from CS until DOUT x three-state disabled
2
t17
Data access time after SCLK rising edge/CS
falling edge
t18
t19
t20
t21
0.4 × tSCLK
0.4 × tSCLK
10
0.4 × tSCLK
0.4 × tSCLK
10
ns min
ns min
ns min
ns max
SCLK low pulse width
SCLK high pulse width
SCLK to data valid hold time after SCLK falling edge
CS rising edge to DOUT x high impedance
18
18
1 Multifunction pin names may be referenced by their relevant function only.
2 A buffer is used on the DOUT x pins (Pin 5 to Pin 7) for this measurement.
200µA
I
OL
TO OUTPUT
PIN
1.6V
C
L
25pF
200µA
I
OH
Figure 2. Load Circuit for Digital Output Timing Specifications
Rev. 0 | Page 5 of 28
AD7656A-1
Data Sheet
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
POWER SUPPLY SEQUENCING
Simultaneous application of VDD and VSS is necessary to
guarantee reliability of the device. In cases where simultaneous
application cannot be guaranteed, VDD must power up before
VSS. When a negative voltage is applied to the analog inputs
before VDD and VSS are fully powered up, a 560 Ω resistor must
be placed on the analog inputs.
Table 3.
Parameter
Rating
VDD to AGND, DGND
VSS to AGND, DGND
VDD to AVCC
AVCC to AGND, DGND
DVCC to AVCC
DVCC to DGND, AGND
AGND to DGND
VDRIVE to DGND
Analog Input Voltage to AGND
Digital Input Voltage to DGND
Digital Output Voltage to DGND
REFIN/REFOUT to AGND
Input Current to Any Pin Except Supplies1
Operating Temperature Range
Storage Temperature Range
Junction Temperature
Pb/Sn Temperature, Soldering
Reflow (10 sec to 30 sec)
0 V to +16.5 V
0 V to −16.5 V
AVCC + 0.7 V to +16.5 V
−0.3 V to +7 V
−0.3 V to AVCC + 0.3 V
−0.3 V to +7 V
−0.3 V to +0.3 V
−0.3 V to DVCC + 0.3 V
VSS + 1 V to VDD − 1 V
−0.3 V to VDRIVE + 0.3 V
−0.3 V to VDRIVE + 0.3 V
−0.3 V to AVCC + 0.3 V
10 mA
−40°C to +85°C
−65°C to +150°C
150°C
A number of sequencing combinations can lead to temporary
high current states; however, when all supplies are powered up,
the device returns to normal operating currents. The analog
input (AIN) coming before AVCC causes temporary high current
on the analog inputs. Digital inputs before DVCC, and DVCC
before other supplies, also cause temporary high current states.
THERMAL RESISTANCE
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages. These
specifications apply to a 4-layer board.
Table 4. Thermal Resistance
Package Type
θJA
θJC
Unit
240(0)°C
64-Lead LQFP
45
11
°C/W
Pb-Free Temperature, Soldering Reflow 260(0)°C
ESD 1.5 kV
ESD CAUTION
1 Transient currents of up to 100 mA do not cause SCR latch-up.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. 0 | Page 6 of 28
Data Sheet
AD7656A-1
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
1
2
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
DB14/REFBUF
V6
AV
AV
V5
EN/DIS
DB13
PIN 1
CC
CC
3
DB12
DB11
4
5
DB10/DOUT C
DB9/DOUT B
DB8/DOUT A
DGND
AGND
AGND
V4
6
AD7656A-1
7
TOP VIEW
8
(Not to Scale)
AV
AV
V3
CC
CC
9
V
DRIVE
10
11
12
13
14
15
16
DB7/HBEN/DCEN
DB6/SCLK
AGND
AGND
V2
DB5/DCIN A
DB4/DCIN B
DB3/DCIN C
DB2/SEL C
AV
AV
V1
CC
CC
DB1/SEL B
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Figure 3. Pin Configuration
Table 5. Pin Function Descriptions
Pin No.
Mnemonic
Description1
1
Data Bit 14/Reference Buffer Enable and Disable. When SER/PAR/SEL = 0, this pin acts as a three-
state digital input/output pin.
DB14/REFBUFEN
/DIS
2, 3, 64
DB13, DB12, DB15
Data Bit 12, Data Bit 13, and Data Bit 15. When SER/PAR/SEL = 0, these pins act as three-state parallel
digital input/output pins. When CS and RD are low, these pins are used to output the conversion
result. When CS and WR are low, these pins are used to write to the control register. When SER/PAR/SEL =
1, tie these pins to DGND.
4
5
DB11
Data Bit 11. When SER/PAR/SEL = 0, this pin acts as a three-state parallel digital output pin. When
SER/PAR/SEL = 1, tie this pin to DGND.
DB10/DOUT C
Data Bit 10/Serial Data Output C. When SER/PAR/SEL = 0, this pin acts as a three-state parallel digital
output pin. When SER/PAR/SEL = 1 and SEL C = 1, this pin functions as DOUT C and outputs serial
conversion data. This pin configures the serial interface to have three DOUT x output lines.
Data Bit 9/Serial Data Output B. When SER/PAR/SEL = 0, this pin acts as a three-state parallel digital
output pin. When SER/PAR/SEL = 1 and SEL B = 1, this pin functions as DOUT B and outputs serial
conversion data. This pin configures the serial interface to have two DOUT x output lines.
Data Bit 8/Serial Data Output A. When SER/PAR/SEL = 0, this pin acts as a three-state parallel digital
output pin. When SER/PAR/SEL = 1 and SEL A = 1, this pin functions as DOUT A and outputs serial
conversion data.
6
7
DB9/DOUT B
DB8/DOUT A
8, 25
9
DGND
VDRIVE
Digital Ground. This is the ground reference point for all digital circuitry on the AD7656A-1. Connect
both DGND pins to the DGND plane of a system. The DGND and AGND voltages should ideally be at the
same potential and must not be more than 0.3 V apart, even on a transient basis.
Logic Power Supply Input. The voltage supplied at this pin determines the operating voltage of the
interface. This pin is nominally at the same supply as the supply of the host interface.
Rev. 0 | Page 7 of 28
AD7656A-1
Data Sheet
Pin No.
Mnemonic
Description1
10
DB7/HBEN/DCEN
Data Bit 7/High Byte Enable/Daisy-Chain Enable. When the parallel interface is selected and the device is
used in word mode (SER/PAR/SEL = 0 and W/B = 0), Pin 10 functions as Data Bit 7. When the parallel
interface is selected and the device is used in byte mode (SER/PAR/SEL = 0 and W/B = 1), Pin 10 functions
as HBEN. If the HBEN is logic high, the data is output MSB byte first on DB15 to DB8. If HBEN is logic
low, the data is output LSB byte first on DB15 to DB8. When the serial interface is selected (SER/PAR/SEL =
1), Pin 10 functions as DCEN. If the DCEN is logic high, the AD7656A-1 operates in daisy-chain mode
with DB5 to DB3 functioning as DCIN A to DCIN C. When the serial interface is selected but the
device is not used in daisy-chain mode, tie DCEN to DGND.
11
12
13
14
15
DB6/SCLK
Data Bit 6/Serial Clock. When SER/PAR/SEL = 0, this pin acts as a three-state parallel digital output
pin. When SER/PAR/SEL = 1, this pin functions as the SCLK input and is the read serial clock for the
serial transfer.
DB5/DCIN A
DB4/DCIN B
DB3/DCIN C
DB2/SEL C
Data Bit 5/Daisy-Chain Input A. When SER/PAR/SEL is low, this pin acts as a three-state parallel
digital output pin. When SER/PAR/SEL = 1 and DCEN = 1, this pin acts as Daisy-Chain Input A. When
the serial interface is selected, but the device is not used in daisy-chain mode, tie this pin to DGND.
Data Bit 4/Daisy-Chain Input B. When SER/PAR/SEL = 0, this pin acts as a three-state parallel digital
output pin. When SER/PAR/SEL = 1 and DCEN = 1, this pin acts as Daisy-Chain Input B. When the serial
interface is selected, but the device is not used in daisy-chain mode, tie this pin to DGND.
Data Bit 3/Daisy-Chain Input C. When SER/PAR/SEL = 0, this pin acts as a three-state parallel digital
output pin. When SER/PAR/SEL = 1 and DCEN = 1, this pin acts as Daisy-Chain Input C. When the serial
interface is selected, but the device is not used in daisy-chain mode, tie this pin to DGND.
Data Bit 2/Select DOUT C. When SER/PAR/SEL = 0, this pin acts as a three-state parallel digital output
pin. When SER/PAR/SEL = 1, this pin functions as SEL C and is used to configure the serial interface. If
this pin is 1, the serial interface operates with three DOUT x output pins and enables DOUT C as a
serial output. If this pin is 0, the DOUT C is not enabled to operate as a serial data output pin. Leave
unused serial DOUT x pins unconnected.
16
17
DB1/SEL B
DB0/SEL A
Data Bit 1/Select DOUT B. When SER/PAR/SEL = 0, this pin acts as a three-state parallel digital output
pin. When SER/PAR/SEL = 1, this pin functions as SEL B and is used to configure the serial interface. If
this pin is 1, the serial interface operates with two or three DOUT x output pins and enables DOUT B
as a serial output. If this pin is 0, DOUT B is not enabled to operate as a serial data output pin and
only one DOUT output pin, DOUT A, is used. Leave unused serial DOUT x pins unconnected.
Data Bit 0/Select DOUT A. When SER/PAR/SEL = 0, this pin acts as a three-state parallel digital output
pin. When SER/PAR/SEL = 1, this pin functions as SEL A and is used to configure the serial interface. If
this pin is 1, the serial interface operates with one, two, or three DOUT x output pins and enables
DOUT A as a serial output. When the serial interface is selected, always set this pin to 1.
18
19
BUSY
CS
Busy Output. This pin transitions to high when a conversion is started and remains high until the
conversion is complete and the conversion data is latched into the output data registers. A new
conversion cannot be initiated on the AD7656A-1 when the BUSY signal is high because any applied
CONVST edges are ignored.
Chip Select. This active low logic input frames the data transfer. If both CS and RD are logic low and
the parallel interface is selected, the output bus is enabled, and the conversion result is output on
the parallel data bus lines. If both CS and WR are logic low and the parallel interface is selected, DB15 to
DB8 are used to write data to the on-chip control register. When the serial interface is selected, the
CS is used to frame the serial read transfer and clock out the MSB of the serial output data.
20
RD
Read Data. If both CS and RD are logic low and the parallel interface is selected, the output bus is
enabled. When the serial interface is selected, hold the RD line low.
21, 22, 23
CONVST C,
Conversion Start Input A, Conversion Start Input B, and Conversion Start Input C. These logic inputs
CONVST B, CONVST A are used to initiate conversions on the ADC pairs. CONVST A is used to initiate simultaneous conversions
on V1 and V2. CONVST B is used to initiate simultaneous conversions on V3 and V4. CONVST C is
used to initiate simultaneous conversions on V5 and V6. When one of these pins switches from low
to high, the track-and-hold switch on the selected ADC pair switches from track to hold mode, and
the conversion is initiated. These inputs can also be used to place the ADC pairs into partial power-
down mode.
24
26
STBY
Standby Mode Input. This pin is used to put all six on-chip ADCs into standby mode. The STBY pin is
high for normal operation and low for standby operation.
Digital Power, 4.75 V to 5.25 V. The DVCC and AVCC voltages should ideally be at the same potential
and must not be more than 0.3 V apart, even on a transient basis. Decouple this supply to DGND by
placing a 1 µF decoupling capacitor on the DVCC pin.
DVCC
Rev. 0 | Page 8 of 28
Data Sheet
AD7656A-1
Pin No.
Mnemonic
Description1
27
RANGE
Analog Input Range Selection. Logic input. The logic level on this pin determines the input range of
the analog input channels. When this pin is Logic 1 at the falling edge of BUSY, the range for the
next conversion is 2 × VREF. When this pin is Logic 0 at the falling edge of BUSY, the range for the
next conversion is 4 × VREF. In hardware select mode, the RANGE pin is checked on the falling edge
of BUSY. In software mode (H/S SEL = 1), the RANGE pin can be tied to DGND, and the input range is
determined by the RNGA, RNGB, and RNGC bits in the control register (see Table 9).
28
RESET
Reset Input. When set to logic high, this pin resets the AD7656A-1. In software mode, the current
conversion is aborted, and the internal register is set to all 0s. In hardware mode, the AD7656A-1 is
configured depending on the logic levels on the hardware select pins. In all modes, the AD7656A-1
should receive a RESET pulse after power-up. The RESET high pulse should be typically 100 ns wide.
The CONVST x pin may be held high during the RESET pulse. However, if the CONVST x pin is held low
during the RESET pulse, after the RESET pulse, the AD7656A-1 needs to receive a complete CONVST x
pulse to initiate the first conversion; this consists of a high-to-low CONVST x edge followed by a low-
to-high CONVST x edge. In hardware mode, the user can initiate a RESET pulse between conversion
cycles, that is, a 100 ns RESET pulse can be applied to the device after BUSY has transitioned from high
to low and the data has been read. The RESET can then be issued prior to the next complete CONVST x
pulse. Ensure that in such a case, RESET has returned to logic low prior to the next complete CONVST x
pulse.
29
W/B
Word/Byte Input. When this pin is logic low, data can be transferred to and from the AD7656A-1 using
the parallel data lines DB15 to DB0. When this pin is logic high and the parallel interface is selected,
byte mode is enabled. In this mode, data is transferred using the DB15 to DB8 data lines, and DB7
functions as HBEN. To obtain the 16-bit conversion result, 2-byte reads are required. When the serial
interface is selected, tie this pin to DGND.
30
31
VSS
VDD
Negative Power Supply Voltage. This is the negative supply voltage for the analog input section.
Positive Power Supply Voltage. This is the positive supply voltage for the analog input section.
32, 37, 38, 43,
44, 49, 52, 53,
55, 57, 59
AGND
Analog Ground. This pin is the ground reference point for all analog circuitry on the AD7656A-1. Refer
all analog input signals and external reference signals to this pin. Connect all AGND pins to the
AGND plane of the system. The AGND and DGND voltages should ideally be at the same potential
and must not be more than 0.3 V apart, even on a transient basis.
33, 36, 39,
42, 45, 48
V1 to V6
Analog Input 1 to Analog Input 6. These pins are single-ended analog inputs. In hardware mode,
the analog input range of these channels is determined by the RANGE pin. In software mode, it is
determined by the RNGC to RNGA bits of the control register (see Table 9).
34, 35, 40,
41, 46, 47,
50, 60
AVCC
Analog Supply Voltage, 4.75 V to 5.25 V. This is the supply voltage for the ADC cores. The AVCC and
DVCC voltages should ideally be at the same potential and must not be more than 0.3 V apart, even
on a transient basis.
51
REFIN/REFOUT
Reference Input/Reference Output. The on-chip reference is available via this pin. Alternatively, the
internal reference can be disabled, and an external reference can be applied to this input. See the
Internal/External Reference section. When the internal reference is enabled, decouple this pin using
at least a 1 µF decoupling capacitor.
54, 56, 58
61
REFCAPA, REFCAPB,
REFCAPC
Reference Capacitor A, Reference Capacitor B, and Reference Capacitor C. Decoupling capacitors are
connected to these pins to decouple the reference buffer for each ADC pair. Decouple each REFCAP x pin
to AGND using a 1 µF capacitor.
Serial/Parallel Selection Input. When this pin is low, the parallel interface is selected. When this pin is high,
the serial interface is selected. When the serial interface is selected, DB10 to DB8 function as DOUT C to
DOUT A, DB0 to DB2 function as DOUT x, and DB7 functions as DCEN. When the serial interface is
selected, tie DB15 and DB13 to DB11 to DGND.
SER/PAR SEL
62
63
H/S SEL
Hardware/Software Select Input. Logic input. When H/S SEL = 0, the AD7656A-1 is operated in
hardware select mode, and the ADC pairs to be simultaneously sampled are selected by the
CONVST pins. When H/S SEL = 1, the ADC pairs to be sampled simultaneously are selected by
writing to the control register. When the serial interface is selected, CONVST A is used to initiate
conversions on the selected ADC pairs.
Write Data/Reference Enable and Disable. When the H/S SEL pin is high and both CS and WR are
logic low, DB15 to DB8 are used to write data to the internal control register. When the H/S SEL pin is
low, this pin is used to enable or disable the internal reference. When H/S SEL = 0 and REFEN/DIS = 0, the
internal reference is disabled and an external reference should be applied to the REFIN/REFOUT pin.
When H/S SEL = 0 and REFEN/DIS = 1, the internal reference is enabled and the REFIN/REFOUT pin
should be decoupled. See the Internal/External Reference section.
WR/REFEN/DIS
1 Multifunction pin names may be referenced by their relevant function only.
Rev. 0 | Page 9 of 28
AD7656A-1
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
2.0
1.5
0
V
/V = ±12V
T = –40°C
A
= 5V DNL WCP = 0.61LSB
V
/V = ±15V
DD SS
DD SS
AV /DV /V
fSAMPLE = 250kSPS
2 × V
AV /DV /V
±10V RANGE
= 5V
CC
CC DRIVE
CC
CC DRIVE
–20
DNL WCN = –0.82LSB
RANGE
INTERNAL REFERENCE
REF
–40
T
= 25°C
1.0
fSAAMPLE = 250kSPS
fIN = 10kHz
–60
0.5
SNR = 88.44dB
SINAD = 88.43dB
THD = –111.66dB
–80
0
–100
–120
–140
–160
–180
–0.5
–1.0
–1.5
–2.0
0
10k
20k
30k
CODE
40k
50k
60k 65535
0
20
40
60
80
100
120
FREQUENCY (kHz)
Figure 7. Typical DNL
Figure 4. FFT for 10 V Range (VDD/VSS
=
15 V)
90
89
88
87
86
85
84
83
0
–20
fSAMPLE = 250kSPS
= 25°C
INTERNAL REFERENCE
V
/V = ±12V
DD SS
T
AV /DV /V
±5V RANGE
INTERNAL REFERENCE
= 5V
A
CC
CC DRIVE
±10V RANGE
/V = ±12V
V
DD SS
–40
AV /DV /V
= 5V
T
= 25°C
CC
CC DRIVE
fSAAMPLE = 250kSPS
fIN = 10kHz
–60
SNR = 88.25dB
SINAD = 88.24dB
THD = –112.46dB
±5V RANGE
–80
V
/V = ±12V
DD SS
AV /DV /V
= 5V
CC
CC DRIVE
–100
–120
–140
–160
–180
10
100
0
20
40
60
80
100
120
ANALOG INPUT FREQUENCY (kHz)
FREQUENCY (kHz)
Figure 8. SINAD vs. Analog Input Frequency
Figure 5. FFT for 5 V Range (VDD/VSS
=
12 V)
–80
–85
2.0
1.5
1.0
0.5
0
V
/V = ±12V
T = –40°C
A
= 5V INL WCP = 0.97LSB
fSAMPLE = 250kSPS
A
INTERNAL REFERENCE
DD SS
AV /DV /V
fSAMPLE = 250kSPS
2 × V
T
= 25°C
CC
CC DRIVE
INL WCN = –0.72LSB
RANGE
REF
–90
–95
±10V RANGE
/V = ±12V
V
DD SS
–100
–105
–110
–115
AV /DV /V
= 5V
CC
CC DRIVE
–0.5
–1.0
–1.5
–2.0
±5V RANGE
/V = ±12V
V
DD SS
AV /DV /V
= 5V
CC
CC DRIVE
10
100
0
10k
20k
30k
CODE
40k
50k
60k 65535
ANALOG INPUT FREQUENCY (kHz)
Figure 9. THD vs. Analog Input Frequency
Figure 6. Typical INL
Rev. 0 | Page 10 of 28
Data Sheet
AD7656A-1
3.20
3.15
3.10
3.05
3.00
2.95
2.90
2.85
2.80
2.75
2.70
–80
AV /DV /V
= 5V
V
/V = ±16.5V
CC
CC DRIVE
DD SS
V
/V = ±12V
AV /DV /V
= 5.25V
DD SS
CC
CC DRIVE
T
= 25°C
R
= 1000Ω
A
SOURCE
INTERNAL REFERENCE
±4 × V RANGE
–90
–100
–110
–120
REF
R
= 220Ω
SOURCE
R
= 50Ω
SOURCE
R
= 100Ω
SOURCE
R
= 10Ω
SOURCE
–55
–35
–15
5
25
45
65
85
105
125
10
100
TEMPERATURE (°C)
ANALOG INPUT FREQUENCY (kHz)
Figure 10. THD vs. Analog Input Frequency for Various Source Impedances,
4 × VREF Range
Figure 13. Conversion Time vs. Temperature
–80
3500
3000
2500
2000
1500
1000
500
V
/V = ±12V
DD SS
3212
AV /DV /V
= 5V
CC
CC DRIVE
V
/V = ±15V
DD SS
T
= 25°C
–85
–90
A
AV /DV /V
INTERNAL REFERENCE
8192 SAMPLES
= 5V
CC
CC DRIVE
2806
INTERNAL REFERENCE
±2 × V
RANGE
REF
R
= 1000Ω
–95
SOURCE
1532
–100
–105
–110
–115
R
= 220Ω
R
= 100Ω
SOURCE
SOURCE
R
= 50Ω
SOURCE
R
= 10Ω
392
–3
SOURCE
168
25
57
–4
0
0
3
0
–5
10
100
–2
–1
0
1
2
ANALOG INPUT FREQUENCY (kHz)
CODE
Figure 11. THD vs. Analog Input Frequency for Various Source Impedances,
2 × VREF Range
Figure 14. Histogram of Codes
2.510
100
90
80
70
60
50
40
f
= 250kSPS
RANGE
AV /DV /V
= 5V
SAMPLE
CC
CC DRIVE
±2 × V
INTERNAL REFERENCE
T
V
/V = ±12V
REF
DD SS
2.508
2.506
2.504
2.502
2.500
2.498
2.496
2.494
2.492
= 25°C
= 10kHz
A
f
IN
100nF ON V AND V
DD
SS
V
SS
V
DD
–55
–35
–15
5
25
45
65
85
105
125
30
80
130 180 230 280 330 380 430 480 530
SUPPLY RIPPLE FREQUENCY (kHz)
TEMPERATURE (°C)
Figure 12. Reference Voltage vs. Temperature
Figure 15. PSRR vs. Supply Ripple Frequency
Rev. 0 | Page 11 of 28
AD7656A-1
Data Sheet
90
22
20
18
16
14
12
10
±5V RANGE
±10V RANGE
89
88
±10V RANGE
AV /DV /V
= 5.25V
CC DRIVE
CC
V
/V = ±16.5V
DD SS
±5V RANGE
AV /DV /V
= 5V
CC DRIVE
CC
V
/V = ±12V
DD SS
87
86
85
AV /DV /V
= 5V
CC
CC DRIVE
fSAMPLE = 250kSPS
fIN = 10kHz
INTERNAL REFERENCE
f
= 250kSPS
SAMPLE
FOR ±5V RANGE V /V = ±12V
DD SS
FOR ±10V RANGE V /V = ±16.5V
DD SS
–40
–20
0
20
40
60
80
100
120
140
–40
–20
0
20
40
60
80
100
120
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 16. SNR vs. Temperature
Figure 19. Dynamic Current vs. Temperature
–90
–95
95
90
85
80
75
70
65
60
fSAMPLE = 250kSPS
fIN = 10kHz
INTERNAL REFERENCE
–100
–105
–110
–115
–120
±5V RANGE
AV /DV /V
= 5V
CC
CC DRIVE
V
/V = ±12V
DD SS
fSAMPLE = 250kSPS
±2 × V
RANGE
REF
INTERNAL REFERENCE
±10V RANGE
AV /DV /V
V
T
= 25°C
fIAN = 10kHz
= 5.25V
CC DRIVE
/V = ±16.5V
CC
DD SS
1µF ON AV SUPPLY PIN
CC
±100mV SUPPLY RIPPLE AMPLITUDE
–60 –40 –20
0
20
40
60
80
100 120
140
30
70
110
150
190
230
TEMPERATURE (°C)
SUPPLY RIPPLE FREQUENCY (kHz)
Figure 17. THD vs. Temperature
Figure 20. PSRR vs. Supply Ripple Frequency for AVCC Supply
120
110
100
90
80
AV /DV /V
= 5V
CC
CC DRIVE
V
/V = ±12V
DD SS
T
= 25°C
A
70
INTERNAL REFERENCE
±2 × V RANGE
REF
30kHz ON SELECTED CHANNEL
20 40 60 80
FREQUENCY OF INPUT NOISE (kHz)
60
0
100
120
140
Figure 18. Channel-to-Channel Isolation vs. Frequency of Input Noise
Rev. 0 | Page 12 of 28
Data Sheet
AD7656A-1
TERMINOLOGY
The ratio depends on the number of quantization levels in the
digitization process: the more levels, the smaller the quantization
noise. The theoretical SINAD ratio for an ideal N-bit converter
with a sine wave input is given by
Integral Nonlinearity (INL)
The INL is the maximum deviation from a straight line passing
through the endpoints of the ADC transfer function. The
endpoints of the transfer function are zero scale at a ½ LSB below
the first code transition and full scale at ½ LSB above the last
code transition.
SINAD = (6.02 N + 1.76) dB
Therefore, SINAD is 98 dB for a 16-bit converter.
Differential Nonlinearity (DNL)
The DNL is the difference between the measured and the ideal
1 LSB change between any two adjacent codes in the ADC.
Total Harmonic Distortion (THD)
The THD is the ratio of the rms sum of the harmonics to the
fundamental. For the AD7656A-1, it is defined as
Bipolar Zero-Scale Error
2
2
2
2
2
V2 +V3 +V4 +V5 +V6
The bipolar zero-scale error is the deviation of the midscale
transition (all 1s to all 0s) from the ideal VIN voltage, that is,
AGND − 1 LSB.
THD (dB) = 20 log
V1
where:
V1 is the rms amplitude of the fundamental.
Bipolar Zero-Scale Error Matching
The bipolar zero-scale error matching is the difference in
bipolar zero-code error between any two input channels.
V2, V3, V4, V5, and V6 are the rms amplitudes of the second
through sixth harmonics.
Positive Full-Scale Error
Peak Harmonic or Spurious Noise
The positive full-scale error is the deviation of the last code
transition (011 … 110 to 011 … 111) from the ideal (4 × VREF
1 LSB or 2 × VREF − 1 LSB) after adjusting for the bipolar zero-
scale error.
The peak harmonic or spurious noise is the ratio of the rms
value of the next largest component in the ADC output
spectrum (up to fSAMPLE/2, excluding dc) to the rms value of
the fundamental. Normally, the value of this specification is
determined by the largest harmonic in the spectrum, but for
ADCs where the harmonics are buried in the noise floor, it is
determined by a noise peak.
−
Positive Full-Scale Error Matching
The positive full-scale error matching is the difference in
positive full-scale error between any two input channels.
Intermodulation Distortion (IMD)
Negative Full-Scale Error
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities creates distortion
products at the sum and difference frequencies of mfa nfb,
where m, n = 0, 1, 2, 3. Intermodulation distortion terms are
those for which neither m nor n are equal to 0. For example, the
second-order terms include (fa + fb) and (fa − fb), and the
third-order terms include (2fa + fb), (2fa − fb), (fa + 2fb), and
(fa − 2fb).
The negative full-scale error is the deviation of the first code
transition (10 … 000 to 10 … 001) from the ideal (−4 × VREF
1 LSB or −2 × VREF + 1 LSB) after adjusting for the bipolar zero
scale error.
+
Negative Full-Scale Error Matching
The negative full-scale error matching is the difference in
negative full-scale error between any two input channels.
Track-and-Hold Acquisition Time
The AD7656A-1 is tested using the CCIF standard in which two
input frequencies near the maximum input bandwidth are used.
In this case, the second-order terms are usually distanced in
frequency from the original sine waves, and the third-order
terms are usually at a frequency close to the input frequencies.
As a result, the second- and third-order terms are specified
separately. The calculation of the intermodulation distortion is
per the THD specification, where it is the ratio of the rms sum
of the individual distortion products to the rms amplitude of
the sum of the fundamentals and is expressed in decibels.
The track-and-hold amplifier returns to track mode at the end
of the conversion. The track-and-hold acquisition time is the
time required for the output of the track-and-hold amplifier to
reach its final value, within 1 LSB, after the end of the conversion.
See the Track-and-Hold section for more details.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the measured output signal
to the rms sum of all other spectral components below the
Nyquist frequency. The value for SNR is expressed in decibels.
Signal-to-Noise-and-Distortion (SINAD) Ratio
The SINAD ratio is the measured ratio of signal-to-noise-and-
distortion at the output of the ADC. The signal is the rms
amplitude of the fundamental. Noise is the sum of all
nonfundamental signals up to half the sampling frequency
(fSAMPLE/2, excluding dc).
Channel-to-Channel Isolation
Channel-to-channel isolation is a measure of the level of crosstalk
between any two channels. It is measured by applying a full-scale,
100 kHz sine wave signal to all unselected input channels and
determining the degree to which the signal attenuates in the
selected channel with a 30 kHz signal.
Rev. 0 | Page 13 of 28
AD7656A-1
Data Sheet
Power Supply Rejection Ratio (PSRR)
the VDD and VSS supplies of the ADC at a frequency sampled,
f
SAMPLE, as follows:
Variations in power supply affect the full-scale transition but
not the linearity of the converter. Power supply rejection is the
maximum change in the full-scale transition point due to a change
in power supply voltage from the nominal value. See the Typical
Performance Characteristics section.
PSRR (dB) = 10 log(Pf/PfS)
where:
Pf is equal to the power at Frequency f in the ADC output.
PfS is equal to the power at Frequency fSAMPLE coupled onto the
Figure 15 shows the power supply rejection ratio vs. supply ripple
frequency for the AD7656A-1. The power supply rejection ratio
is defined as the ratio of the power in the ADC output at full-scale
frequency, f, to the power of a 200 mV p-p sine wave applied to
VDD and VSS supplies.
Percent Full-Scale Ratio (% FSR)
%FSR is calculated using the full theoretical span of the ADC.
Rev. 0 | Page 14 of 28
Data Sheet
AD7656A-1
THEORY OF OPERATION
CONVERTER DETAILS
Analog Input
The AD7656A-1 can handle true bipolar input voltages. The
logic level on the RANGE pin or the value written to the RNGx
bits in the control register determines the analog input range on
the AD7656A-1 for the next conversion. When the RANGE pin or
RNGx bit is 1, the analog input range for the next conversion is
2 × VREF. When the RANGE pin or RNGx bit is 0, the analog
The AD7656A-1 is a pin- and software-compatible, reduced
decoupling version of the AD7656A device. In addition, the
AD7656A-1 is a high speed, low power converter that allows the
simultaneous sampling of six on-chip analog-to-digital converters
(ADCs). The analog inputs on the AD7656A-1 can accept true
bipolar input signals. The RANGE pin or RNGx bits are used to
select either 4 × VREF or 2 × VREF as the input range for the
next conversion.
input range for the next conversion is 4 × VREF
.
V
DD
The AD7656A-1 contains six successive approximation (SAR)
ADCs, six track-and-hold amplifiers, an on-chip 2.5 V reference,
reference buffers, and high speed parallel and serial interfaces.
The device allows the simultaneous sampling of all six ADCs
when the three CONVST x pins (CONVST A, CONVST B, and
CONVST C) are tied together. Alternatively, the six ADCs can
be grouped into three pairs. Each pair has an associated CONVST x
signal used to initiate simultaneous sampling on each ADC pair,
on four ADCs, or on all six ADCs. CONVST A is used to initiate
simultaneous sampling on V1 and V2, CONVST B is used to
initiate simultaneous sampling on V3 and V4, and CONVST C
is used to initiate simultaneous sampling on V5 and V6.
V
V
DD_INTERNAL
D1
C2
R1
V1
C1
D2
SS_INTERNAL
V
SS
Figure 21. Equivalent Analog Input Structure
Figure 21 shows an equivalent circuit of the analog input of
structure of the AD7656A-1. The two diodes, D1 and D2,
provide ESD protection for the analog inputs. Ensure that the
analog input signal never exceeds the VDD and VSS supply rail
limits by more than VSS + 1 V and VDD − 1 V. Signals exceeding
this value cause these diode to become forward-biased and to start
conducting into the substrate. The maximum current these diodes
can conduct without causing irreversible damage to the device is
10 mA. The C1 capacitor in Figure 21 is typically about 4 pF and
can be attributed primarily to pin capacitance. The R1 resistor is
a lumped component made up of the on resistance of a switch
(that is, a track-and-hold switch). This resistor is typically about
3.5 kΩ. The C2 capacitor is the ADC sampling capacitor and
has a capacitance of 10 pF typically.
A conversion is initiated on the AD7656A-1 by pulsing the
CONVST x input. On the rising edge of CONVST x, the track-
and-hold amplifier of the selected ADC pair is placed into hold
mode and the conversions are started. After the rising edge of
CONVST x, the BUSY signal goes high to indicate that the
conversion is taking place. The conversion clock for the
AD7656A-1 is internally generated, and the conversion time for
the device is 3 µs. Any further CONVST rising edges on either
CONVST A, CONVST B, or CONVST C are ignored as long as
BUSY is high. The BUSY signal returns low to indicate the end of
a conversion. On the falling edge of BUSY, the track-and-hold
amplifier returns to track mode. Data can be read from the output
register via the parallel or serial interface.
The AD7656A-1 requires VDD and VSS dual supplies for the high
voltage analog input structures. These supplies must be greater
than the analog input range (see Table 6 for the requirements on
these supplies for each analog input range).
Track-and-Hold Amplifiers
The AD7656A-1 requires a low voltage AVCC supply of 4.75 V to
5.25 V to power the ADC core, a DVCC supply of 4.75 V to 5.25 V
for the digital power, and a VDRIVE supply of 2.7 V to 5.25 V for
the interface power.
The track-and-hold amplifiers on the AD7656A-1 allow the ADCs
to accurately convert an input sine wave of full-scale amplitude
to 16-bit resolution. The input bandwidth of the track-and-hold
amplifiers is greater than the Nyquist rate of the ADC, even
when the AD7656A-1 is operating at the maximum throughput
rate. The device can handle input frequencies of up to 4.5 MHz.
To meet the specified performance when using the minimum
supply voltage for the selected analog input range, it may be
necessary to reduce the throughput rate from the maximum
throughput rate.
The track-and-hold amplifiers sample their respective inputs
simultaneously on the rising edge of CONVST x. The aperture time
(that is, the delay time between the external CONVST x signal
actually entering hold) for the track-and-hold amplifier is 10 ns.
This is well matched across all six track-and-hold amplifiers on one
device and from device to device. This allows more than six ADCs
to be sampled simultaneously. The end of the conversion is signaled
by the falling edge of BUSY, and it is at this point that the track-
and-hold amplifiers return to track mode and the acquisition
time begins.
Table 6. Minimum VDD/VSS Supply Voltage Requirements
Analog Input
Range (V)
Reference
Full-Scale
Input (V)
Minimum
VDD/VSS (V)
Voltage (V)
4 × VREF
2 × VREF
2.5
2.5
11
6
11
6
Rev. 0 | Page 15 of 28
AD7656A-1
Data Sheet
The AD7656A-1 contains three on-chip reference buffers as
ADC TRANSFER FUNCTION
shown in Figure 23. Each of the three ADC pairs has an
associated reference buffer. These reference buffers require
external decoupling capacitors, using 1 µF capacitors, on the
REFCAPA, REFCAPB, and REFCAPC pins. The internal
reference buffers can be disabled in software mode by writing to
Bit DB8 in the internal control register. If a serial interface is
selected, the internal reference buffers can be disabled in hardware
mode by setting the DB14/REFBUFEN/DIS pin high. If the internal
reference and its buffers are disabled, apply an external buffered
reference to the REFCAPx pins.
The output coding of the AD7656A-1 is twos complement. The
designed code transitions occur midway between successive
integer LSB values, that is, 1⁄2 LSB, 3⁄2 LSB. The LSB size is
FSR/65,536 for the AD7656A-1. The ideal transfer characteristic
is shown in Figure 22.
011 ... 111
011 ... 110
000 ... 001
000 ... 000
111 ... 111
REFCAPA
SAR
SAR
BUF
BUF
BUF
100 ... 010
100 ... 001
100 ... 000
AGND – 1LSB
REFIN/
REFOUT
–FSR/2 + 1/2LSB
+FSR/2 – 3/2LSB
ANALOG INPUT
REF
SAR
SAR
REFCAPB
Figure 22. Transfer Characteristic
The LSB size is dependent on the analog input range selected
(see Table 7).
SAR
SAR
Table 7. LSB Size for Each Analog Input Range
REFCAPC
Input Range (V)
LSB Size (mV)
Full Scale Range
Figure 23. Reference Circuit
10
5
0.305
0.152
20 V/65,536
10 V/65,536
TYPICAL CONNECTION DIAGRAM
Figure 24 shows the typical connection diagram for the
AD7656A-1, illustrating the reduction in the number and value
of decoupling capacitors that are required. There are eight AVCC
supply pins on each device. The AVCC supplies are the supplies
used for the AD7656A-1 conversion process; therefore, decouple
them well. The AVCC supply applied to the eight AVCC pins can
be decoupled using just one 1 µF capacitor. The AD7656A-1 can
operate with the internal reference or an externally applied
reference. In this configuration, the device is configured to
operate with the external reference. The REFIN/REFOUT pin is
decoupled with a 1 µF capacitor. The three internal reference
buffers are enabled. Each of the REFCAPx pins is decoupled
with a 1 µF capacitor.
INTERNAL/EXTERNAL REFERENCE
The REFIN/REFOUT pin allows access to the 2.5 V reference of
the AD7656A-1, or it allows an external reference to be
connected, providing the reference source for conversion.
The AD7656A-1 can accommodate a 2.5 V external reference.
When applying an external reference via the REFIN/REFOUT
pin, the internal reference must be disabled, and the reference
buffers must be enabled. Alternatively, an external reference can be
applied via the REFCAPx pins, in which case, disable the internal
reference, and it is also recommended to disable the reference
buffers to save power and minimize crosstalk. After a reset, the
AD7656A-1 defaults to operating in external reference mode with
the internal reference disabled and the reference buffers
enabled.
If the same supply is being used for the AVCC and DVCC supplies,
place a ferrite or small RC filter between the supply pins.
The internal reference can be enabled in either hardware or
software mode. To enable the internal reference in hardware mode,
The AGND pins are connected to the analog ground plane of
the system. The DGND pins are connected to the digital ground
plane in the system. Connect the AGND and DGND planes
together at one place in the system. Make this connection as
close as possible to the AD7656A-1 in the system.
H
set the /S SEL pin to 0 and the REFEN/DIS pin to 1. To enable the
H
internal reference in software mode, set /S SEL to 1 and write to
the control register to set Bit DB9 of the register to 1. For the
internal reference mode, decouple the REFIN/REFOUT pin using a
1 µF capacitor.
Rev. 0 | Page 16 of 28
Data Sheet
AD7656A-1
DV
CC
+
DIGITAL SUPPLY
VOLTAGE +3V OR +5V
ANALOG SUPPLY
VOLTAGE 5V
+
+
1µF
1µF
1µF
AGND AV
DD
DV
DGND
V DGND
DRIVE
CC
CC
1
+11V TO +16.5V
V
SUPPLY
+
+
+
1µF
1µF
1µF
PARALLEL
INTERFACE
D0 TO D15
AGND
MICROCONTROLLER/
MICROPROCESSOR/
DSP
RESET
CS
RD
BUSY
REFCAPA, REFCAPB, REFCAPC
AGND
2.5V
REF
REFIN/OUT CONVST A, CONVST B, CONVST C
SER/PAR
AGND
H/S
W/B
RANGE
AD7656A-1
SIX ANALOG
INPUTS
1
–11V TO –16.5V
V
SS
SUPPLY
V
STBY
DRIVE
1µF
+
AGND
NOTES
1
SEE THE POWER SUPPLY SEQUENCING SECTION.
Figure 24. Typical Connection Diagram
The VDRIVE supply is connected to the same supply as the
processor. The voltage on VDRIVE controls the voltage value of
the output logic signals.
Four read pulses (in parallel mode) are applied and data from
V1, V2, V5, and V6 are output. Data from V3 and V4 is not
output because CONVST B was not toggled in this cycle.
However, when in serial mode, all zeros are output in place of
the ADC result for ADCs not included in the conversion cycle.
See the Serial Interface (SER//SEL = 1) section for more
information.
Decouple the VDD and VSS signals with a minimum 1 μF decoupling
capacitor. These supplies are used for the high voltage analog
input structures on the AD7656A-1 analog inputs.
DRIVING THE ANALOG INPUTS
Parallel Interface (SER/ /SEL = 0)
PAR
Together, the driver amplifier and the analog input circuit used
for the AD7656A-1 must settle for a full-scale step input to a 16-bit
level (0.0015%), which is within the specified 550 ns acquisition
time of the AD7656A-1. The noise generated by the driver
amplifier must be kept as low as possible to preserve the signal-
to-noise ratio (SNR) and transition noise performance of the
AD7656A-1. In addition, the driver also needs to have a THD
performance suitable for the AD7656A-1.
The AD7656A-1 consists of six 16-bit ADCs. A simultaneous
sample of all six ADCs can be performed by connecting all
three CONVST x pins (CONVST A, CONVST B, and
CONVST C) together. The AD7656A-1 needs to see a CONVST x
pulse to initiate a conversion, consisting of a falling CONVST x
edge followed by a rising CONVST x edge. The rising edge of
CONVST x initiates simultaneous conversions on the selected
ADCs. The AD7656A-1 contains an on-chip oscillator that is
used to perform the conversions. The conversion time, tCONV, is
3 μs. The BUSY signal goes low to indicate the end of a
conversion. The falling edge of the BUSY signal is used to place
the track-and-hold amplifier into track mode.
The AD8021 meets these requirements. The AD8021 needs an
external compensation capacitor of 10 pF. If a dual version of
the AD8021 is required, the AD8022 can be used. The AD8610
and the AD797 can also be used to drive the AD7656A-1.
INTERFACE OPTIONS
The AD7656A-1 also allows the six ADCs to be converted
simultaneously in pairs by pulsing the three CONVST x pins
independently. CONVST A is used to initiate simultaneous
conversions on V1 and V2, CONVST B is used to initiate
simultaneous conversions on V3 and V4, and CONVST C is used
to initiate simultaneous conversions on V5 and V6. The conversion
results from the simultaneously sampled ADCs are stored in the
output data registers. Note that when a rising edge occurs on any
one CONVST x pin to initiate a conversion, any further CONVST
rising edges on any of the CONVST x pins are ignored while BUSY
is high.
The AD7656A-1 provides two interface options: a high speed
parallel interface and a high speed serial interface. The required
interface mode is selected via the SER/
interface can operate in word ( /B = 0) or byte ( /B = 1)
mode. When in serial mode, the AD7656A-1 can be configured
into daisy-chain mode.
PAR
SEL pin. The parallel
W
W
When in parallel mode, a read operation only accesses the results
related to conversions that have just occurred. For example,
consider the case where CONVST A and CONVST C are toggled
simultaneously but CONVST B is not used. At the end of the
conversion process, when BUSY goes low, a read is implemented.
Rev. 0 | Page 17 of 28
AD7656A-1
Data Sheet
Data can be read from the AD7656A-1 via the parallel data bus
Although a conversion can be initiated during a read sequence,
it is not recommended practice, because doing so can affect the
performance of the conversion. For the specified performance,
it is recommended to perform the read after the conversion.
For unused input channel pairs, tie the associated CONVST x
CS
RD
W
with standard
and
signals ( /B = 0). To read the data over
PAR CS RD
the parallel bus, tie SER/
SEL low. The
and
input
signals are internally gated to enable the conversion result onto
the data bus. The data lines, the DB0 to DB15 pins, leave their
pin to VDRIVE
.
CS
RD
high impedance state when both
and
are logic low.
If there is only an 8-bit bus available, the parallel interface of the
CS
RD
The
signal can be permanently tied low, and the
signal
W
AD7656A-1 can be configured to operate in byte mode ( /B = 1).
can be used to access the conversion results. A read operation
can take place after the BUSY signal goes low. The number of
required read operations depends on the number of ADCs that
are simultaneously sampled (see Figure 25). If CONVST A
and CONVST B are simultaneously brought low, four read
operations are required to obtain the conversion results from
V1, V2, V3, and V4. If CONVST A and CONVST C are
simultaneously brought low, four read operations are required
to obtain the conversion results from V1, V2, V5, and V6.
The conversion results are output in ascending order.
In this configuration, the DB7/HBEN/DCEN pin takes on its
HBEN function. Each channel conversion result from the
AD7656A-1 can be accessed in two read operations, with eight
bits of data provided on DB15 to DB8 for each of the read
operations (see Figure 26). The HBEN pin determines whether
the read operation first accesses the high byte or the low byte of
the 16-bit conversion result. To always access the low byte first
on DB15 to DB8, tie the HBEN pin low. To always access the
high byte first on DB15 to DB8, tie the HBEN pin high. In byte
mode when all three CONVST x pins are pulsed together to initiate
simultaneous conversions on all six ADCs, 12 read operations
are necessary to read back the six 16-bit conversion results.
Leave DB6 to DB0 unconnected in byte mode.
When using the three CONVST x signals to independently
initiate conversions on the three ADC pairs, when a rising edge
occurs on any one CONVST x pin to initiate a conversion, any
further CONVST rising edges on any of the CONVST x pins are
ignored while BUSY is high.
t10
CONVST A,
CONVST B,
CONVST C
tCONV
tACQ
BUSY
t4
CS
t3
t2
t5
RD
t9
t7
t6
t8
tQUIET
DATA
V1
V2
V3
V4
V5
V6
W
Figure 25. Parallel Interface Timing Diagram ( /B = 0)
CS
t4
t3
t9
t5
RD
t8
t7
t6
DB15 TO DB8
LOW BYTE
HIGH BYTE
W
Figure 26. Parallel Interface—Read Cycle for Byte Mode of Operation ( /B = 1, HBEN = 0)
Rev. 0 | Page 18 of 28
Data Sheet
AD7656A-1
The AD7656A-1 control register allows individual ranges to be
programmed on each ADC pair. DB12 to DB10 bits in the
control register are used to program the range on each ADC pair.
SOFTWARE SELECTION OF ADCS
H
The /S SEL pin determines the source of the combination of ADCs
H
that are to be simultaneously sampled. When the /S SEL pin is
After a reset occurs on the AD7656A-1, the control register
contains all 0s. The CONVST A signal is used to initiate a
simultaneous conversion on the combination of channels
selected via the control register. The CONVST B and
CONVST C signals can be tied low when operating in software
logic low, the combination of channels to be simultaneously
sampled is determined by the CONVST A, CONVST B, and
H
CONVST C pins. When the /S SEL pin is logic high, the
combination of channels selected for simultaneous sampling is
determined by the contents of the DB15 to DB13 bits in the
control registers. In this mode, a write to the control register is
necessary.
H
mode ( /S SEL = 1). The number of read pulses required
depends on the number of ADCs selected in the control register
and on whether the devices are operating in word or byte mode.
The conversion results are output in ascending order.
The control register is an 8-bit write-only register. Data is
CS
WR
written to this register using the
and
pins and the DB15
During the write operation, Data Bus Bit DB15 to Data Bus Bit DB8
are bidirectional and become inputs to the control register when
to DB8 data pins (see Figure 27). The control register is detailed
in Table 8 and Table 9. To select an ADC pair to be simultaneously
sampled, set the corresponding data line high during the write
operation.
RD
CS
WR
is logic high and
and
are logic low. The logic state
on DB15 through DB8 is latched into the control register when
WR
goes logic high.
CS
WR
t13
t12
t11
t15
t14
DB15 TO DB8
DATA
W
Figure 27. Parallel Interface—Write Cycle for Word Mode ( /B = 0)
Table 8. Control Register Bit Map (Default All Zeros)
DB15
DB14
DB13
DB12
DB11
DB10
DB9
DB8
VC
VB
VA
RNGC
RNGB
RNGA
REFEN
REFBUF
Table 9. Control Register Bit Function Descriptions
Bit
Mnemonic Description
DB15 VC
This bit selects the V5 and V6 analog inputs for the next conversion. When this bit is set to 1, V5 and V6 are
simultaneously converted on the next CONVST A rising edge.
DB14 VB
This bit selects the V3 and V4 analog inputs for the next conversion. When this bit is set to 1, V3 and V4 are
simultaneously converted on the next CONVST A rising edge.
DB13 VA
This bit selects the V1 and V2 analog inputs for the next conversion. When this bit is set to 1, V1 and V2 are
simultaneously converted on the next CONVST A rising edge.
DB12 RNGC
DB11 RNGB
DB10 RNGA
This bit selects the analog input range for the V5 and V6 analog inputs. When this bit is set to 1, the 2 × VREF range is
selected for the next conversion. When this bit is set to 0, the 4 × VREF range is selected for the next conversion.
This bit selects the analog input range for the V3 and V4 analog inputs. When this bit is set to 1, the 2 × VREF range is
selected for the next conversion. When this bit is set to 0, the 4 × VREF range is selected for the next conversion.
This bit selects the analog input range for the V1 and V2 analog inputs. When this bit is set to 1, the 2 × VREF range is
selected for the next conversion. When this bit is set to 0, the 4 × VREF range is selected for the next conversion.
DB9
DB8
REFEN
This bit selects the internal reference or an external reference. When this bit is set to 0, the external reference mode is
selected. When this bit is set to 1, the internal reference is selected.
REFBUF
This bit selects between using the internal reference buffers and choosing to bypass these reference buffers. When
this bit is set to 0, the internal reference buffers are enabled, and decoupling is required on the REFCAPx pins. When
this bit is set to 1, the internal reference buffers are disabled, and a buffered reference must be applied to the REFCAPx pins.
Rev. 0 | Page 19 of 28
AD7656A-1
Data Sheet
with the new conversion results, and data can be read from the
AD7656A-1. To read the data back from the device over the
H
Changing the Analog Input Range ( /S SEL = 0)
The AD7656A-1 RANGE pin allows the user to select either 2 ×
REF or 4 × VREF as the analog input range for the six analog
PAR
serial interface, tie SER/
SEL high. The
and SCLK signals
CS
V
are used to transfer data from the AD7656A-1. The device has
three DOUT x pins: DOUT A, DOUT B, and DOUT C. Data can
be read back from the AD7656A-1 using one, two, or all three
DOUT x lines.
H
inputs. When the /S SEL pin is low, the logic state of the
RANGE pin is sampled on the falling edge of the BUSY signal to
determine the range for the next simultaneous conversion. When
the RANGE pin is logic high at the falling edge of the BUSY
signal, the range for the next conversion is 2 × VREF. When the
RANGE pin is logic low at the falling edge of the BUSY signal,
the range for the next conversion is 4 × VREF. After a RESET
pulse, the range is updated on the first falling BUSY edge.
Figure 28 shows six simultaneous conversions and the read
sequence using three DOUT x lines. Also in Figure 28, 32 SCLK
transfers are used to access data from the AD7656A-1; however,
CS
two 16 SCLK individually framed transfers with the
signal
can also be used to access the data on the three DOUT x lines.
Any additional SCLKs applied after this result in an output of
all zeros. When the serial interface is selected and conversion
data is clocking out on all three DOUT x lines, tie DB0/SEL A,
DB1/SEL B, and DB2/SEL C to VDRIVE. These pins are used to
enable the DOUT A to DOUT C lines, respectively.
H
Changing the Analog Input Range ( /S SEL = 1)
H
When the /S SEL pin is high, the range can be changed by
writing to the control register. Bits[DB12:DB10] in the control
register are used to select the analog input ranges for the next
conversion. Each analog input pair has an associated range bit,
allowing independent ranges to be programmed on each ADC
pair. When the RNGx bit is set to 1, the range for the next
If it is required to clock conversion data out on two data output
lines, use DOUT A and DOUT B. To enable DOUT A and
DOUT B, tie DB0/SEL A and DB1/SEL B to VDRIVE, and tie
DB2/SEL C tied low. When six simultaneous conversions are
performed and only two DOUT x lines are used, a 48 SCLK
transfer can be used to access the data from the AD7656A-1.
Any additional SCLKs applied after this result in an output of
all zeros. The read sequence is shown in Figure 29 for a
simultaneous conversion on all six ADCs using two DOUT x
lines. If a simultaneous conversion occurred on all six ADCs,
and only two DOUT x lines are used to read the results from
the AD7656A-1, DOUT A clocks out the result from V1, V2,
and V5, and DOUT B clocks out the results from V3, V4, and V6.
conversion is 2 × VREF. When the RNGx bit is set to 0, the range
for the next conversion is 4 × VREF
.
Serial Interface (SER/ /SEL = 1)
PAR
By pulsing one, two, or all three CONVST signals, the AD7656A-1
uses its on-chip trimmed oscillator to simultaneously convert
the selected channel pairs on the rising edge of CONVST x.
After the rising edge of CONVST x, the BUSY signal goes high to
indicate that the conversion has started. It returns low when the
conversion is complete, 3 µs later. Any further CONVST x rising
edges on either CONVST A, CONVST B, or CONVST C are
ignored as long as BUSY is high. The output register is loaded
CONVST A,
CONVST B,
CONVST C
tCONV
tACQ
BUSY
CS
16
32
SCLK
tQUIET
DOUT A
V1
V3
V5
V2
V4
V6
DOUT B
DOUT C
Figure 28. Serial Interface with Three DOUT x Lines
CS
48
SCLK
DOUT A
DOUT B
V5
V6
V1
V3
V2
V4
Figure 29. Serial Interface with Two DOUT x Lines
Rev. 0 | Page 20 of 28
Data Sheet
AD7656A-1
t1
CONVST A,
CONVST B,
CONVST C
t10
tACQ
tCONV
t2
BUSY
ACQUISITION
CONVERSION
ACQUISITION
CS
tQUIET
t19
t18
SCLK
t16
t17
t20
DOUT A,
DOUT B,
DOUT C
t21
DB15
DB14
DB13
DB1
DB0
Figure 30. Serial Read Operation
Data can also be clocked out using just one DOUT x line, in which
case, use DOUT A to access the conversion data. To configure
the AD7656A-1 to operate in this mode, tie DB0/SEL A to
SERIAL READ OPERATION
Figure 30 shows the timing diagram for reading data from the
AD7656A-1 when the serial interface. The SCLK input signal
VDRIVE, and tie DB1/SEL B and DB2/SEL C low. The disadvantage
CS
provides the clock source for the serial interface. The
goes low to access data from the AD7656A-1. The falling edge
CS
signal
of using only one DOUT x line is that the throughput rate is
reduced. Data can be accessed from the AD7656A-1 using one
96-SCLK transfer, three 32-SCLK individually framed transfers, or
six 16-SCLK individually framed transfers. Any additional SCLKs
applied after this result in an output of all zeros. When using the
of
takes the bus out of three-state and clocks out the MSB of
the 16-bit conversion result. The ADCs output 16 bits for each
conversion result; the data stream of the AD7656A-1 consists of 16
bits of conversion data, provided MSB first.
RD
serial interface, tie the
signal low, and leave the unused
The first bit of the conversion result is valid on the first SCLK
DOUT x line(s) unconnected.
CS
falling edge after the
falling edge. The subsequent 15 data
Whether one, two, or three data output lines are used, if a
particular CONVST x pin is not used in the conversion cycle,
all zeros are output in place of the ADC result for the associated
ADCs even though they were not used in the conversion cycle.
This means that if, for example, only CONVST B is pulsed and
one data output pin is in use, 64 SCLKs are required to access
the results from V3 and V4; however, only 32 SCLKs are required if
two or three data output lines are in use.
bits are clocked out on the rising edge of the SCLK signal. Data
is valid on the SCLK falling edge. To access each conversion result,
16 clock pulses must be provided to the AD7656A-1. Figure 30
shows how a 16-SCLK read is used to access the conversion
results.
Rev. 0 | Page 21 of 28
AD7656A-1
Data Sheet
CONVERT
DIGITAL HOST
CONVST x
CONVST x
DATA IN1
DATA IN2
DOUT A
DOUT B
DCIN A
DCIN B
DOUT A
AD7656A-1
AD7656A-1 DOUT B
SCLK
CS
SCLK
CS
CS
SCLK
DCEN = 0
DEVICE 2
DCEN = 1
DEVICE 1
Figure 31. Daisy-Chain Configuration
CONVST A,
CONVST B,
CONVST C
BUSY
CS
1
2
3
15
16
17
31
32
33
47
48
49
63
64
65
94
95
96
SCLK
DEVICE 1, DOUT A
DEVICE 1, DOUT B
DEVICE 2, DOUT A
DEVICE 2, DOUT B
MSB V1
MSB V3
MSB V1
MSB V3
LSB V1 MSB V2
LSB V3 MSB V4
LSB V1 MSB V2
LSB V3 MSB V4
LSB V2 MSB V5
LSB V4 MSB V6
LSB V2 MSB V5
LSB V4 MSB V6
LSB V5 MSB V1
LSB V6 MSB V3
LSB V5
LSB V1 MSB V2
LSB V3 MSB V4
LSB V5
LSB V6
LSB V6
Figure 32. Daisy-Chain Serial Interface Timing with Two DOUT Lines
CS
The
falling edge is used to frame the serial transfer from the
DAISY-CHAIN MODE (DCEN = 1, SER/PAR/SEL = 1)
AD7656A-1, to take the bus out of three-state, and to clock out
the MSB of the first conversion result. In the example shown in
Figure 32, all 12 ADC channels are simultaneously sampled.
Two DOUT x lines are used to read the conversion results in
When reading conversion data back from the AD7656A-1 using
one, two, three DOUT x pins, it is possible to configure the
AD7656A-1 to operate in daisy-chain mode by using the DCEN
pin. This daisy-chain feature allows multiple AD7656A-1 devices
to be cascaded together and is useful for reducing the component
count and wiring connections. An example connection of two
devices is shown in Figure 31. This configuration shows two
DOUT x lines being used for each device. Simultaneous sampling
of the 12 analog inputs is possible by using a common CONVST x
signal. The DB5, DB4, and DB3 data pins are used as the
DCIN A to DCIN C data input pins for the daisy-chain mode.
CS
this example. frames a 96-SCLK transfer. During the first
48 SCLKs, the conversion data is transferred from Device 2 to
Device 1. DOUT A on Device 2 transfers conversion data from
V1, V2, and V5 into DCIN A in Device 1; and DOUT B on
Device 2 transfers conversion results from V3, V4, and V6 to
DCIN B in Device 1. During the first 48 SCLKs, Device 1 transfers
data into the digital host. DOUT A on Device 1 transfers
conversion data from V1, V2, and V5; DOUT B on Device 1
transfers conversion data from V3, V4, and V6. During the last
48-SCLKs, Device 2 clocks out zeros, and Device 1 shifts the
data clocked in from Device 2 during the first 48-SCLKs into
the digital host. This example can also be implemented using
six 16-SCLK individually framed transfers if DCEN remains
high during the transfers.
The rising edge of CONVST is used to initiate a conversion on
the AD7656A-1. After the BUSY signal has gone low to indicate
that the conversion is complete, the user can begin to read the data
from the two devices. Figure 32 shows the serial timing diagram
when operating two AD7656A-1 devices in daisy-chain mode.
Rev. 0 | Page 22 of 28
Data Sheet
AD7656A-1
CONVST A,
CONVST B,
CONVST C
BUSY
CS
1
2
3
15
16
17
31
32
33
47
48
49
63
64
SCLK
DEVICE 1, DOUT A
DEVICE 1, DOUT B
DEVICE 1, DOUT C
DEVICE 2, DOUT A
DEVICE 2, DOUT B
DEVICE 2, DOUT C
MSB V1
MSB V3
MSB V5
MSB V1
MSB V3
MSB V5
LSB V1 MSB V2
LSB V3 MSB V4
LSB V5 MSB V6
LSB V1 MSB V2
LSB V3 MSB V4
LSB V5 MSB V6
LSB V2 MSB V1
LSB V4 MSB V3
LSB V6 MSB V5
LSB V2
LSB V1 MSB V2
LSB V3 MSB V4
LSB V5 MSB V6
LSB V2
LSB V4
LSB V6
LSB V4
LSB V6
Figure 33. Daisy-Chain Serial Interface Timing with Three DOUT x Lines
Figure 33 shows the timing if two AD7656A-1 devices are
configured in daisy-chain mode and are operating with three
DOUT x lines. Assuming that a simultaneous sampling of all
and ADC 2 enter partial power-down, and ADC 3 to ADC 6
remain fully powered. At Point B in Figure 34, ADC1 and ADC 2
begin to power up. When the required power-up time has
elapsed, a conversion can be initiated on the next CONVST x
rising edge as shown.
CS
12 inputs occurs, the
frames a 64-SCLK transfer during the
read operation. During the first 32 SCLKs of this transfer, the
conversion results from Device 1 are clocked into the digital
host and the conversion results from Device 2 are clocked into
Device 1. During the last 32 SCLKs of the transfer, the conversion
results from Device 2 are clocked out of Device 1 and into the
digital host, and Device 2 clocks out 0s.
A
B
tWAKE-UP
CONVST A
BUSY
The maximum number of devices in the chain is limited by the
throughput required per channel depending on the application
needs, the SCLK frequency used, and the number of serial data
lines used.
CONVST B
CONVST C
Figure 34. Entering and Exiting Partial Power-Down Mode
The AD7656A-1 has a standby mode whereby the device can be
placed into a low power consumption mode (315 µW maximum).
The AD7656A-1 is placed into standby mode by bringing the
Standby/Partial Power-Down Modes of Operation
PAR
PAR
/SEL = 1)
(SER/
/SEL = 0 or SER/
Each ADC pair can be individually placed into partial power-
down mode at the end of their conversion by bringing the
associated CONVST x signal low before the falling edge of
BUSY. If a CONVST x pin is low when BUSY goes low, the
associated ADC pair only enters partial power-down mode if
they were actually converting within that cycle, that is, if that
particular CONVST x pin was used to trigger conversions. To
power an ADC pair back up, bring the CONVST x signal high
to tell the ADC pair to power up and place the track-and-hold
amplifier into track mode. After the power-up time from partial
power-down has elapsed, the CONVST x signal can receive a
rising edge to initiate a valid conversion. In partial power-down
mode, the reference buffers remain powered up. When an ADC
pair is in partial power-down mode, conversions can still occur
on the other fully powered ADCs. In Figure 34 at Point A, ADC 1
STBY
operation by bringing
input
logic low and can be powered up again for normal
STBY
logic high. The output data buffers
are still operational when the AD7656A-1 is in standby mode,
meaning the user can continue to access the conversion results
of the device. This standby feature can be used to reduce the
average power consumed by the AD7656A-1 when operating at
lower throughput rates. The device can be placed into standby
at the end of each conversion when BUSY goes low and is taken
out of standby mode prior to the next conversion. The time for
the AD7656A-1 to come out of standby is called the wake-up
time. The wake-up time limits the maximum throughput rate at
which the AD7656A-1 can operate when powering down between
conversions. See the Specifications section for additional
information.
Rev. 0 | Page 23 of 28
AD7656A-1
Data Sheet
APPLICATION HINTS
For the power supply lines to the AVCC, DVCC, VDRIVE, VDD, and VSS
pins on the AD7656A-1, use as large a trace as possible to
provide low impedance paths and to reduce the effect of glitches
on the power supply lines. Establish good connections between
the AD7656A-1 supply pins and the power tracks on the board;
this must involve the use of a single via or multiple vias for each
supply pin.
LAYOUT
Design the printed circuit board (PCB) that houses the AD7656A-1
so that the analog and digital sections are separated and confined
to different areas of the board.
Use at least one ground plane. The ground plane can be
common or split between the digital and analog sections. In the
case of the split plane, join the digital and analog ground in only
one place, preferably underneath the AD7656A-1, or at least as
close as possible to the device.
Good decoupling is also important to lower the supply impedance
presented to the AD7656A-1 and to reduce the magnitude of
the supply spikes. Place the decoupling capacitors near, but
ideally right up against, these pins and their corresponding
ground pins. Additionally, place low ESR 1 µF capacitors on each
of the supply pins, the REFIN/REFOUT pin, and each REFCAPx
pin. Avoid sharing these capacitors between pins, and use vias
to connect the capacitors to the power and ground planes. In
addition, use wide, short traces between each via and the
capacitor pad, or place the vias adjacent to the capacitor pad to
minimize parasitic inductances. The AD7656A-1 offers the user a
reduced decoupling solution that is pin and software compatible
with the AD7656A. The recommended reduced decoupling
required for AD7656A-1 is outlined in Figure 24.
If the AD7656A-1 is in a system where multiple devices require
analog-to-digital ground connections, still make the connection
at one point only, a star ground point, established as close as
possible to the AD7656A-1. Make good connections to the
ground plane. Avoid sharing one connection for multiple
ground pins. Use individual vias or multiple vias to the ground
plane for each ground pin.
Avoid running digital lines under the device because doing so
couples noise onto the die. Allow the analog ground plane to
run under the AD7656A-1 to avoid noise coupling. Shield fast
switching signals like CONVST x or clocks with digital ground
to avoid radiating noise to other sections of the board, and
never run the fast switching signals near the analog signal
paths. Avoid crossover of digital and analog signals. Run traces
on layers in close proximity on the board at right angles to each
other to reduce the effect of feedthrough through the board.
Rev. 0 | Page 24 of 28
Data Sheet
AD7656A-1
OUTLINE DIMENSIONS
12.20
12.00 SQ
11.80
0.75
0.60
0.45
1.60
MAX
64
49
1
48
PIN 1
10.20
10.00 SQ
9.80
TOP VIEW
(PINS DOWN)
1.45
1.40
1.35
0.20
0.09
7°
3.5°
0°
0.08
COPLANARITY
16
33
0.15
0.05
SEATING
17
32
PLANE
VIEW A
0.27
0.22
0.17
0.50
BSC
LEAD PITCH
VIEW A
ROTATED 90° CCW
COMPLIANT TO JEDEC STANDARDS MS-026-BCD
Figure 35. 64-Lead Low Profile Quad Flat Package [LQFP]
(ST-64-2)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
Temperature Range
−40°C to +85°C
−40°C to +85°C
Package Description
Package Option
ST-64-2
ST-64-2
AD7656A-1BSTZ
AD7656A-1BSTZ-RL
64-Lead Low Profile Quad Flat Package [LQFP]
64-Lead Low Profile Quad Flat Package [LQFP]
1 Z = RoHS Compliant Part.
Rev. 0 | Page 25 of 28
AD7656A-1
NOTES
Data Sheet
Rev. 0 | Page 26 of 28
Data Sheet
NOTES
AD7656A-1
Rev. 0 | Page 27 of 28
AD7656A-1
NOTES
Data Sheet
©2013 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D11128-0-12/13(0)
Rev. 0 | Page 28 of 28
相关型号：
AD7656BST-500RL7
6-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PQFP64, MS-026BCD, LQFP-64
ADI
AD7656BSTZ-1
6-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, PQFP64, ROHS COMPLIANT, MS-026BCD, LQFP-64
ROCHESTER
AD7656BSTZ-500RL7
6-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PQFP64, LEAD FREE, MS-026BCD, LQFP-64
ADI
©2020 ICPDF网 联系我们和版权申明