AD8114_15 [ADI]
Low Cost 225 MHz;型号: | AD8114_15 |
厂家: | ADI |
描述: | Low Cost 225 MHz |
文件: | 总33页 (文件大小:1936K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Low Cost 225 MHz
16 × 16 Crosspoint Switches
AD8114/AD8115
FUNCTIONAL BLOCK DIAGRAM
FEATURES
16 × 16 high speed nonblocking switch arrays
AD8114; G = 1
SER/PAR D0 D1 D2 D3 D4
A0
A1
AD8115; G = 2
Serial or parallel programming of switch array
Serial data out allows daisy-chaining of multiple
16 × 16 arrays to create larger switch arrays
High impedance output disable allows connection of
multiple devices without loading the output bus
For smaller arrays see the AD8108/AD8109 (8 × 8) or
AD8110/AD8111 (16× 8) switch arrays
Complete solution
A2
CLK
A3
80-BIT SHIFT REGISTER
WITH 5-BIT
PARALLEL LOADING
DATA
OUT
DATA IN
UPDATE
80
SET
INDIVIDUAL
OR RESET
ALL OUTPUTS
TO "OFF"
PARALLEL LATCH
CE
RESET
80
16
DECODE
16 × 5:16 DECODERS
Buffered inputs
OUTPUT
AD8114/AD8115
BUFFER
G = +1,
G = +2
256
Programmable high impedance outputs
16 output amplifiers, AD8114 (G = 1), AD8115 (G = 2)
Drives 150 Ω loads
Excellent video performance
25 MHz, 0.1 dB gain flatness
0.05%/0.05° differential gain/differential phase error
(RL = 150 Ω)
SWITCH
MATRIX
16
16 INPUTS
OUTPUTS
Excellent ac performance
−3 dB bandwidth: 225 MHz
Slew rate: 375 V/µs
Low power of 700 mW (2.75 mW per point)
Low all hostile crosstalk of −70 dB @ 5 MHz
Reset pin allows disabling of all outputs (connected through
a capacitor to ground provides power-on reset capability)
100-lead LQFP (14 mm × 14 mm)
Figure 1.
flatness out to 25 MHz while driving a 75 Ω back-terminated
load, make the AD8114/AD8115 ideal for all types of signal
switching.
APPLICATIONS
Routing of high speed signals including
Video (NTSC, PAL, S, SECAM, YUV, RGB)
Compressed video (MPEG, wavelet)
3-level digital video (HDB3)
Datacomms
The AD8114/AD8115 include 16 independent output buffers
that can be placed into a high impedance state for paralleling
crosspoint outputs so that off channels do not load the output
bus. The AD8114 has a gain of 1, while the AD8115 offers a
gain of 2. They operate on voltage supplies of 5 ꢀ while
consuming only 70 mA of idle current. The channel switching is
performed via a serial digital control (which can accommodate
daisy-chaining of several devices) or via a parallel control,
allowing updating of an individual output without
Telecomms
GENERAL DESCRIPTION
The AD8114/AD81151 are high speed 16 × 16 video crosspoint
switch matrices. They offer a −3 dB signal bandwidth greater
than 200 MHz and channel switch times of less than 50 ns
with 1% settling. With −70 dB of crosstalk and −90 dB isolation
(@ 5 MHz), the AD8114/AD8115 are useful in many high speed
applications. The differential gain and differential phase of better
than 0.05% and 0.05°, respectively, along with 0.1 dB
1Patent pending.
reprogramming the entire array.
The AD8114/AD8115 is packaged in 100-lead LQFP package
and is available over the extended industrial temperature range
of −40°C to +85°C.
Rev. B
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
© 2005 Analog Devices, Inc. All rights reserved.
IMPORTANT LINKS for the AD8114_8115*
Last content update 08/23/2013 04:02 pm
PARAMETRIC SELECTION TABLES
DESIGN COLLABORATION COMMUNITY
Find Similar Products By Operating Parameters
High Speed Switches
Collaborate Online with the ADI support team and other designers
about select ADI products.
Follow us on Twitter: www.twitter.com/ADI_News
Like us on Facebook: www.facebook.com/AnalogDevicesInc
DOCUMENTATION
Data-acquisition system uses fault protection
CMOS Switches Offer High Performance in Low Power, Wideband
Applications
Enhanced Multiplexing for MEMS Optical Cross Connects
Video Amplifier Products
DESIGN SUPPORT
Submit your support request here:
Linear and Data Converters
Embedded Processing and DSP
FOR THE AD8114
AN-282: Fundamentals of Sampled Data Systems
Telephone our Customer Interaction Centers toll free:
Americas:
Europe:
China:
1-800-262-5643
00800-266-822-82
4006-100-006
1800-419-0108
8-800-555-45-90
EVALUATION KITS & SYMBOLS & FOOTPRINTS
India:
View the Evaluation Boards and Kits page for the AD8114
Russia:
View the Evaluation Boards and Kits page for the AD8115
Symbols and Footprints for the AD8114
Quality and Reliability
Lead(Pb)-Free Data
Symbols and Footprints for the AD8115
SAMPLE & BUY
AD8114
AD8115
View Price & Packaging
Request Evaluation Board
Request Samples
Check Inventory & Purchase
Find Local Distributors
* This page was dynamically generated by Analog Devices, Inc. and inserted into this data sheet.
Note: Dynamic changes to the content on this page (labeled 'Important Links') does not
constitute a change to the revision number of the product data sheet.
This content may be frequently modified.
AD8114/AD8115
TABLE OF CONTENTS
AD8114/AD8115—Specifications ................................................. 3
Power-On Reset.......................................................................... 19
Gain Selection............................................................................. 19
Creating Larger Crosspoint Arrays.......................................... 20
Multichannel ꢀideo ................................................................... 21
Crosstalk...................................................................................... 22
PCB Layout...................................................................................... 25
Evaluation Board ............................................................................ 29
Control the Evaluation Board from a PC................................ 30
Overshoot of PC Printer Ports’ Data Lines............................. 30
Outline Dimensions....................................................................... 31
Ordering Guide .......................................................................... 31
Timing Characteristics (Serial) .................................................. 5
Timing Characteristics (Parallel) ............................................... 6
Absolute Maximum Ratings............................................................ 8
Maximum Power Dissipation ..................................................... 8
ESD Caution.................................................................................. 8
Pin Configuration and Function Descriptions............................. 9
Typical Performance Characteristics ........................................... 11
I/O Schematics................................................................................ 17
Theory of Operation ...................................................................... 18
Applications................................................................................. 18
REVISION HISTORY
9/05—Rev. A to Rev. B
Updated Format.................................................................. Universal
Change to Figure 3 ............................................................................6
Change to Absolute Maximum Ratings..........................................8
Changes to Maximum Power Dissipation Section........................8
Updated Outline Dimensions........................................................31
Changes to Ordering Guide ...........................................................31
11/01—Rev. 0 to Rev. A
Edits to ORDERING GUIDE...........................................................5
Comments added to Outline Dimensions ...................................26
Revision 0: Initial Version
Rev. B | Page 2 of 32
AD8114/AD8115
AD8114/AD8115—SPECIFICATIONS
ꢀS = 5 ꢀ, TA = +25°C, RL = 1 kΩ, unless otherwise noted.
Table 1.
Parameter
Conditions
Min
Typ
Max
Unit
DYNAMIC PERFORMANCE
−3 dB Bandwidth
200 mV p-p, RL = 150 Ω
2 V p-p, RL = 150 Ω
0.1 dB, 200 mV p-p, RL = 150 Ω
0.1 dB, 2 V p-p, RL = 150 Ω
2 V p-p, RL = 150 Ω
150/125
225/200
100/125
25/40
20/40
5
MHz
MHz
MHz
MHz
ns
Gain Flatness
Propagation Delay
Settling Time
Slew Rate
0.1%, 2 V step, RL = 150 Ω
2 V step, RL = 150 Ω
40
375/450
ns
V/µs
NOISE/DISTORTION PERFORMANCE
Differential Gain Error
NTSC or PAL, RL = 1 kΩ
NTSC or PAL, RL = 150 Ω
NTSC or PAL, RL = 1 kΩ
NTSC or PAL, RL = 150 Ω
f = 5 MHz
f = 10 MHz
f = 10 MHz, RL = 150 Ω, one channel
0.01 MHz to 50 MHz
0.05
0.05
0.05
0.05
−70/−64
−60/−52
−90
%
%
Differential Phase Error
Crosstalk, All Hostile
Degrees
Degrees
dB
dB
dB
Off Isolation, Input-Output
Input Voltage Noise
16/18
nV/√Hz
DC PERFORMANCE
Gain Error
No load
RL = 1 kΩ
RL = 150 Ω
No load, channel-channel
RL = 1 kΩ channel-channel
0.05/0.2
0.05/0.2
0.2/0.35
0.01/0.5
0.01/0.5
0.75/1.5
0.08/0.6
0.04/1
%
%
%
%
Gain Matching
%
Gain Temperature Coefficient
OUTPUT CHARACTERISTICS
Output Impedance
ppm/°C
DC, enabled
Disabled
Disabled
Disabled
No load
0.2
10
5
Ω
MΩ
pF
µA
V
V
mA
Output Disable Capacitance
Output Leakage Current
Output Voltage Range
Voltage Range
1
3.0
2.5
3.3
3
65
IOUT = 20 mA
Short-Circuit Current
INPUT CHARACTERISTICS
Input Offset Voltage
Worst case (all configurations)
Temperature coefficient
No load
3
15
5
mV
µV/°C
V
pF
MΩ
µA
10
3.5
5
10
2
Input Voltage Range
Input Capacitance
Input Resistance
3/ 1.5
1
Any switch configuration
Input Bias Current
Per output selected
SWITCHING CHARACTERISTICS
Enable On Time
60
ns
Switching Time, 2 V Step
Switching Transient (Glitch)
50% UPDATE to 1% settling
50
ns
20/30
mV p-p
Rev. B | Page 3 of 32
AD8114/AD8115
Parameter
Conditions
Min
Typ
Max
Unit
POWER SUPPLIES
Supply Current
AVCC, outputs enabled, no load
AVCC, outputs disabled
AVEE, outputs enabled, no load
AVEE, outputs disabled
70/80
27/30
70/80
27/30
16
mA
mA
mA
mA
mA
V
dB
dB
dB
DVCC, outputs enabled, no load
Supply Voltage Range
PSRR
4.5 to 5.5
DC
f = 100 kHz
f = 1 MHz
64
80
66
46
OPERATING TEMPERATURE RANGE
Temperature Range
θJA
Operating (still air)
Operating (still air)
−40 to +85
40
°C
°C/W
Rev. B | Page 4 of 32
AD8114/AD8115
TIMING CHARACTERISTICS (SERIAL)
Table 2. Timing Characteristics
Parameter
Symbol
Min
20
100
20
100
0
Typ
Max
Unit
ns
ns
ns
ns
ns
ns
ns
ns
µs
ns
ns
Serial Data Setup Time
CLK Pulse Width
Serial Data Hold Time
CLK Pulse Separation, Serial Mode
CLK to UPDATE Delay
t1
t2
t3
t4
t5
t6
t7
–
UPDATE Pulse Width
50
CLK to DATA OUT Valid, Serial Mode
Propagation Delay, UPDATE to Switch On or Off
Data Load Time, CLK = 5 MHz, Serial Mode
CLK, UPDATE Rise and Fall Times
RESET Time
200
50
–
–
16
100
200
–
Table 3. Logic Levels
VIH
VIL
VOH
VOL
IIH
IIL
IOH
IOL
RESET, SER/PAR
CLK, DATA IN,
CE, UPDATE
RESET, SER/PAR
CLK, DATA IN,
CE, UPDATE
DATA OUT
DATA OUT
RESET, SER/PAR
CLK, DATA IN,
CE, UPDATE
RESET, SER/PAR
CLK, DATA IN,
CE, UPDATE
DATA OUT
DATA OUT
2.0 V min
0.8 V max
2.7 V min
0.5 V max
20 µA max
−400 µA min
−400 µA max
3.0 mA min
t2
t4
1
CLK
0
LOAD DATA INTO
SERIAL REGISTER
ON FALLING EDGE
t1
t3
1
DATA IN
0
OUT7 (D3)
OUT00 (D0)
t5
OUT7 (D4)
t6
1 = LATCHED
UPDATE
TRANSFER DATA FROM SERIAL
REGISTER TO PARALLEL
LATCHES DURING LOW LEVEL
0 = TRANSPARENT
t7
DATA OUT
Figure 2. Timing Diagram, Serial Mode
Rev. B | Page 5 of 32
AD8114/AD8115
TIMING CHARACTERISTICS (PARALLEL)
Table 4. Timing Characteristics
Parameter
Symbol
Min
20
100
20
100
0
Typ
Max
Unit
ns
ns
ns
ns
Data Setup Time
CLK Pulse Width
Data Hold Time
CLK Pulse Separation
CLK to UPDATE Delay
UPDATE Pulse Width
Propagation Delay, UPDATE to Switch On or Off
CLK, UPDATE Rise and Fall Times
RESET Time
t1
t2
t3
t4
t5
t6
–
ns
50
ns
50
ns
–
100
200
ns
–
ns
Table 5. Logic Levels
VIH
VIL
VOH
VOL
IIH
IIL
IOH
IOL
RESET, SER/PAR,
CLK, D0, D1, D2,
RESET, SER/PAR,
CLK, D0, D1, D2,
DATA OUT
DATA OUT
RESET, SER/PAR,
CLK, D0, D1, D2,
RESET, SER/PAR,
CLK, D0, D1, D2,
DATA
OUT
DATA
OUT
D3, D4, A0, A1, A2, D3, D4, A0, A1, A2,
D3, D4, A0, A1, A2, D3, D4, A0, A1, A2,
A3, CE, UPDATE
A3, CE, UPDATE
A3, CE, UPDATE
A3, CE, UPDATE
−400 µA
max
3.0 mA
min
2.0 V min
0.8 V max
2.7 V min
0.5 V max
20 µA max
−400 µA min
t2
t4
1
CLK
0
t1
t3
1
D0–D3
A0–A2
0
t5
t6
1 = LATCHED
UPDATE
0 = TRANSPARENT
Figure 3. Timing Diagram, Parallel Mode
Rev. B | Page 6 of 32
AD8114/AD8115
Table 6. Operation Truth Table
CE UPDATE
SER/
PAR
RESET
CLK DATA IN
DATA OUT
X
Datai-80
Operation/Comment
1
0
X
1
X
X
Datai
X
1
X
0
No change in logic.
The data on the serial DATA IN line is loaded into
serial register. The first bit clocked into the serial register
appears at DATA OUT 80 clocks later.
f
0
0
X
1
0
X
D0…D4,
A0… A3
NA in parallel mode
1
1
0
1
X
X
The data on the parallel data lines, D0 to D4, are
loaded into the 80 bit serial shift register location
addressed by A0 to A3.
Data in the 80-bit shift register transfers into the
parallel latches that control the switch array.
Latches are transparent.
f
X
X
X
X
X
X
Asynchronous operation. All outputs are disabled.
Remainder of logic is unchanged.
D0
D1
D2
D3
D4
PARALLEL
DATA
(OUTPUT
ENABLE)
SER/PAR
S
S
S
S
S
S
S
S
S
S
S
S
D1
D1
D1
D1
D1
D1
D1
D1
D1
D1
D1
D1
DATA
OUT
D Q
CLK
D
Q
Q
D Q
CLK
D
Q
D
Q
D
Q
D
Q
D
Q
D
Q
D
Q
D
Q
D
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
DATA IN
(SERIAL)
D0
D0
D0
D0
D0
D0
D0
D0
D0
D0
D0
D0
CLK
CLK
CLK
CLK
CLK
CLK
CLK
CLK
CLK
CLK
CLK
CE
UPDATE
OUT0 EN
OUT1 EN
OUT2 EN
OUT3 EN
OUT4 EN
OUT5 EN
OUT6 EN
OUT7 EN
OUT8 EN
OUT9 EN
OUT10 EN
OUT11 EN
OUT12 EN
OUT13 EN
OUT14 EN
OUT15 EN
A0
A1
A2
A3
LE
D
LE
D
LE
D
LE
D
LE
D
LE
D
LE
D
LE
D
LE
D
LE
D
LE
D
LE
D
OUT0
B0
OUT0
B1
OUT0
B2
OUT0
B3
OUT0
EN
OUT1
B0
OUT14
EN
OUT15
B0
OUT15
B1
OUT15
B2
OUT15
B3
OUT15
EN
Q
Q
Q
Q
CLR
Q
Q
CLR
Q
Q
Q
Q
Q
CLR Q
RESET
(OUTPUT ENABLE)
DECODE
16
OUTPUT ENABLE
256
SWITCH MATRIX
Figure 4. Logic Diagram
Rev. B | Page 7 of 32
AD8114/AD8115
ABSOLUTE MAXIMUM RATINGS
Table 7.
Parameter
Supply Voltage
Internal Power Dissipation1
AD8114/AD8115 100-Lead
Plastic LQFP (ST)
Input Voltage
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rating
12.0 V
2.6 W
VS
Observe power
derating curves
Output Short-Circuit Duration
Storage Temperature Range2
−65°C to +125°C
1 Specification is for device in free air (TA = 25°C):
100-lead plastic LQFP (ST): θJA = 40°C/W.
2 Maximum reflow temperatures are to JEDEC industry standard J-STD-020.
5
MAXIMUM POWER DISSIPATION
T
= 125°C
J
The maximum power that can be safely dissipated by the
AD8114/AD8115 is limited by the associated rise in junction
temperature. The maximum safe junction temperature for
plastic encapsulated devices is determined by the glass transition
temperature of the plastic, approximately 125°C. Temporarily
exceeding this limit may cause a shift in parametric performance
due to a change in the stresses exerted on the die by the package.
Exceeding a junction temperature of 125°C for an extended
period can result in device failure.
4
3
2
1
0
While the AD8114/AD8115 are internally short-circuit
protected, this may not be sufficient to guarantee that the
maximum junction temperature (125°C) is not exceeded under
all conditions. To ensure proper operation, it is necessary to
observe the maximum power derating curves shown in Figure 5.
–50 –40 –30 –20 –10
0
10 20 30 40 50 60 70 80 90
AMBIENT TEMPERATURE (°C)
Figure 5. Maximum Power Dissipation vs. Temperature
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. B | Page 8 of 32
AD8114/AD8115
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
DVCC
DVCC
PIN 1
2
DGND
DGND
AGND
IN07
3
4
AGND
IN08
5
AGND
IN09
AGND
IN06
6
7
AGND
IN10
AGND
IN05
8
9
AGND
IN11
AGND
IN04
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
AD8114/AD8115
TOP VIEW
AGND
IN12
AGND
IN03
(Not to Scale)
AGND
IN13
AGND
IN02
AGND
IN14
AGND
IN01
AGND
IN15
AGND
IN00
AGND
AVEE
AVCC
AVCC15
OUT15
AVEE14/15
OUT14
AGND
AVEE
AVCC
AVCC00
OUT00
AVEE00/01
OUT01
NC = NO CONNECT
Figure 6. Pin Configuration
Rev. B | Page 9 of 32
AD8114/AD8115
Table 8. Pin Function Descriptions
Pin No.
Mnemonic
Pin Description
58, 60, 62, 64, 66, 68, 70, 72,
4, 6, 8, 10, 12, 14, 16, 18
INxx
Analog Inputs. xx = Channels 00 through 15.
96
97
98
95
DATA IN
CLK
DATA OUT
UPDATE
Serial Data Input, TTL Compatible.
Clock, TTL Compatible. Falling edge triggered.
Serial Data Out, TTL Compatible.
Enable (Transparent) Low. Allows serial register to connect directly to switch matrix.
Data latched when high.
100
99
RESET
CE
Disable Outputs, Active Low.
Chip Enable, Enable Low. Must be low to clock in and latch data.
Selects Serial Data Mode, Low or Parallel Data Mode, High. Must be connected.
Analog Outputs. yy = Channels 00 through 15.
94
SER/PAR
OUTyy
53, 51, 49, 47, 45, 43, 41, 39,
37, 35, 33, 31, 29, 27, 25, 23
3, 5, 7, 9, 11, 13, 15, 17, 19, 57,
59, 61, 63, 65, 67, 69, 71, 73
AGND
Analog Ground for Inputs and Switch Matrix. Must be connected.
1, 75
2, 74
20, 56
21, 55
DVCC
DGND
AVEE
AVCC
AVCCxx/yy
AVEExx/yy
A0
A1
A2
A3
D0
+5 V for Digital Circuitry.
Ground for Digital Circuitry.
−5 V for Inputs and Switch Matrix.
+5 V for Inputs and Switch Matrix.
54, 50, 46, 42, 38, 34, 30, 26, 22
52, 48, 44, 40, 36, 32, 28, 24
84
83
82
81
80
79
78
77
76
85 to 93
+5 V for Output Amplifier that is Shared by Channels xx and yy. Must be connected.
–5 V for Output Amplifier that is Shared by Channels xx and yy. Must be connected.
Parallel Data Input, TTL Compatible (output select LSB).
Parallel Data Input, TTL Compatible (output select).
Parallel Data Input, TTL Compatible (output select).
Parallel Data Input, TTL Compatible (output select MSB).
Parallel Data Input, TTL Compatible (input select LSB)
Parallel Data Input, TTL Compatible (input select).
Parallel Data Input, TTL Compatible (input select).
Parallel Data Input, TTL Compatible (input select MSB).
Parallel Data Input, TTL Compatible (output enable).
No Connect.
D1
D2
D3
D4
NC
Rev. B | Page 10 of 32
AD8114/AD8115
TYPICAL PERFORMANCE CHARACTERISTICS
1
2
1
0.2
0.5
GAIN
0.4
0.1
0
–1
–2
–3
200mV p-p
200mV p-p
0.3
0
–1
–2
–3
FLATNESS
0
GAIN
0.2
0.1
0
–0.1
–0.2
–0.3
–0.4
–0.5
–0.6
FLATNESS
2V p-p
–4
–5
–6
–7
–8
–0.1
–0.2
–0.3
–4
–5
–6
–7
200mV p-p
2V p-p
2V p-p
V
R
AS SHOWN
V AS SHOWN
O
R = 150Ω
O
= 150Ω
–0.4
–0.5
L
L
0.1
1
10
100
1000
0.1
1
10
100
1000
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 7. AD8114 Frequency Response, RL = 150 Ω
Figure 10. AD8115 Frequency Response, RL = 150 Ω
3
2
3
2
1
0.4
0.3
0.5
0.4
200mV p-p
0.3
0.2
0.1
0
1
0
200mV p-p
GAIN
GAIN
0.2
0.1
0
0
–1
–2
FLATNESS
–1
–2
FLATNESS
–0.1
–0.2
–0.3
2V p-p
–3
–4
–5
–3
–4
–5
–6
–7
–0.1
–0.2
–0.3
200mV p-p
2V p-p
–0.4
–0.5
–0.6
2V p-p
V
R
AS SHOWN
= 1kΩ
V
R
AS SHOWN
O
= 1kΩ
O
–6
–7
–0.4
–0.5
L
L
0.1
1
10
100
1000
0.1
1
10
FREQUENCY (MHz)
100
1000
FREQUENCY (MHz)
Figure 8. AD8114 Frequency Response, RL = 1 kΩ
Figure 11. AD8115 Frequency Response, RL = 1 kΩ
10
4
8
6
4
3
2
1
V
R
C
= 200mV p-p
AS SHOWN
= 18pF
V
R
C
= 200mV p-p
AS SHOWN
= 18pF
O
O
L
L
L
L
R = 1kΩ
L
R
= 1kΩ
L
2
0
0
–1
–2
R
= 150Ω
L
R
= 150Ω
L
–2
–4
–6
–3
–4
–5
–6
–8
–10
0.1
1
10
FREQUENCY (MHz)
100
1000
0.1
1
10
FREQUENCY (MHz)
100
1000
Figure 12. AD8115 Frequency Response vs. Load Impedance
Figure 9. AD8114 Frequency Response vs. Load Impedance
Rev. B | Page 11 of 32
AD8114/AD8115
0
0
–10
–20
–30
–40
–50
–60
R
R
= 1kΩ
R
R
= 1kΩ
= 37.5Ω
L
T
L
T
–10
–20
–30
–40
–50
–60
= 37.5Ω
ALL HOSTILE
ALL HOSTILE
ADJACENT
–70
–80
–70
–80
ADJACENT
–90
–90
–100
–100
0.1
1
10
FREQUENCY (MHz)
100
1000
0.1
1
10
FREQUENCY (MHz)
100
1000
Figure 13. AD8114 Crosstalk vs. Frequency
Figure 16. AD8115 Crosstalk vs. Frequency
0
0
V
R
= 2V p-p
= 150Ω
V = 2V p-p
O
–10
O
–10
R
= 150Ω
L
L
–20
–30
–40
–50
–60
–70
–20
–30
–40
–50
–60
–70
2ND HARMONIC
2ND HARMONIC
3RD HARMONIC
–80
–80
3RD HARMONIC
–90
–90
–100
–100
1
10
FUNDAMENTAL FREQUENCY (MHz)
50
1
10
FUNDAMENTAL FREQUENCY (MHz)
50
Figure 14. AD8114 Distortion vs. Frequency
Figure 17. AD8115 Distortion vs. Frequency
V
= 2V STEP
V
= 2V STEP
O
O
R
= 150Ω
R
= 150Ω
L
L
0
5
10
15
20
25
30
35
40
45
0
5
10
15
20
25
30
35
40
45
5ns/DIV
5ns/DIV
Figure 18. AD8115 Settling Time
Figure 15. AD8114 Settling Time
Rev. B | Page 12 of 32
AD8114/AD8115
1M
1M
100k
100k
10k
1k
10k
1k
100
0.1
100
0.1
1
1
10
100
500
10
100
500
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 22. AD8115 Input Impedance vs. Frequency
Figure 19. AD8114 Input Impedance vs. Frequency
1000
100
10
1000
100
10
1
1
0.1
0.1
0.1
1
10
100
1000
0.1
1
10
100
1000
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 20. AD8114 Output Impedance, Enabled vs. Frequency
Figure 23. AD8115 Output Impedance, Enabled vs. Frequency
1M
1M
100k
100k
10k
1k
10k
1k
100
10
100
10
0.1
1
10
100
1000
0.1
1
10
100
1000
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 21. AD8114 Output Impedance, Disabled vs. Frequency
Figure 24. AD8115 Output Impedance, Disabled vs. Frequency
Rev. B | Page 13 of 32
AD8114/AD8115
–40
–50
–60
–70
–40
–50
–60
–70
–80
–90
–80
–90
–100
–110
–100
–110
–120
–130
–140
–120
–130
–140
0.1
1
10
100
500
0.1
1
10
100
500
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 25. AD8114 Off Isolation, Input-Output
Figure 28. AD8115 Off Isolation, Input-Output
–20
–20
–30
–40
–30
–40
+PSRR
–50
–60
–50
–60
–PSRR
–PSRR
+PSRR
–70
–80
–70
–80
–90
–90
–100
0.03
–100
0.03
1
1
0.1
10
0.1
10
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 26. AD8114 PSRR vs. Frequency
Figure 29. AD8115 PSRR vs. Frequency
170
150
170
150
130
110
130
110
90
70
90
70
50
30
10
50
30
10
18nV/√Hz
16nV/√Hz
10
100
1k
10k
100k
1M
10M
10
100
1k
10k
100k
1M
10M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 27. AD8114 Voltage Noise vs. Frequency
Figure 30. AD8115 Voltage Noise vs. Frequency
Rev. B | Page 14 of 32
AD8114/AD8115
V
= 200mV STEP
V = 200mV STEP
O
O
R
= 150Ω
R = 150Ω
0.15V
0.10V
0.15V
0.10V
L
L
0.05V
0V
0.05V
0V
–0.05V
–0.05V
–0.10V
–0.15V
–0.10V
–0.15V
50mV
25ns
50mV
25ns
Figure 31. AD8114 Pulse Response, Small Signal
Figure 34. AD8115 Pulse Response, Small Signal
V
= 2V STEP
V
= 200mV STEP
O
O
R
= 150Ω
R
= 150Ω
1.5V
1.0V
1.5V
1.0V
L
L
0.5V
0V
0.5V
0V
–0.5V
–0.5V
–1.0V
–1.5V
–1.0V
–1.5V
500mV
25ns
500mV
20ns
Figure 32. AD8114 Pulse Response, Large Signal
Figure 35. AD8115 Pulse Response, Large Signal
+5V
0V
+5V
UPDATE
UPDATE
0V
+2V
INPUT 1
AT +1V
+1V
–0V
–1V
–0V
–2V
INPUT 0
AT –1V
INPUT 1
AT +1V
INPUT 0
AT –1V
V
V
OUT
OUT
10ns
10ns
Figure 33. AD8114 Switching Time
Figure 36. AD8115 Switching Time
Rev. B | Page 15 of 32
AD8114/AD8115
5V
5V
UPDATE
UPDATE
0V
0V
0.05V
0.05V
0V
0V
–0.05V
–0.05V
50ns
50ns
Figure 37. AD8114 Switching Transient (Glitch)
Figure 40. AD8115 Switching Transient (Glitch)
260
240
220
200
180
160
240
220
200
180
160
140
140
120
120
100
80
100
80
60
60
40
40
20
0
20
0
–12
–8
–4
0
4
8
–14
–8 –6 –4 –2
0
4
8
10 12 14 16 18
–10
–6
–2
2
6
10
–12 –10
2
6
OFFSET VOLTAGE (mV)
OFFSET VOLTAGE (mV)
Figure 38. AD8114 Offset Voltage Distribution
Figure 41. AD8115 Offset Voltage Distribution
44
40
36
32
28
24
20
16
12
8
44
40
36
32
28
24
20
16
12
8
4
0
4
0
–20 –16 –12
–8
–4
0
4
8
12
16
20
–12
–8
–4
0
4
8
12
16
20
OFFSET VOLTAGE DRIFT (µV/°C)
OFFSET VOLTAGE DRIFT (µV/°C)
Figure 39. AD8114 Offset Voltage Drift Distribution (−40°C to +85°C)
Figure 42. AD8115 Offset Voltage Drift Distribution (−40°C to +85°C)
Rev. B | Page 16 of 32
AD8114/AD8115
I/O SCHEMATICS
V
V
CC
CC
ESD
ESD
ESD
INPUT
INPUT
ESD
AVEE
DGND
Figure 43. Analog Input
Figure 46. Logic Input
V
V
CC
CC
ESD
ESD
2kΩ
ESD
OUTPUT
OUTPUT
ESD
AVEE
DGND
Figure 44. Analog Output
Figure 47. Logic Output
V
CC
20kΩ
ESD
RESET
ESD
DGND
Figure 45. Reset Input
Rev. B | Page 17 of 32
AD8114/AD8115
THEORY OF OPERATION
The AD8114 (G = 1) and AD8115 (G = 2) are crosspoint arrays
with 16 outputs, each of which can be connected to any one of
16 inputs. Organized by output row, 16 switchable
APPLICATIONS
The AD8114/AD8115 have two options for changing the
programming of the crosspoint matrix. In the first option a
serial word of 80 bits can be provided that will update the entire
matrix each time. The second option allows for changing a
single output’s programming via a parallel interface. The serial
option requires fewer signals, but more time (clock cycles) for
changing the programming, while the parallel programming
technique requires more signals, but can change a single output
at a time and requires fewer clock cycles to complete
programming.
transconductance stages are connected to each output buffer in
the form of a 16-to-1 multiplexer. Each of the 16 rows of
transconductance stages are wired in parallel to the 16 input
pins, for a total array of 256 transconductance stages. Decoding
logic for each output selects one (or none) of the
transconductance stages to drive the output stage. The
transconductance stages are NPN-input differential pairs,
sourcing current into the folded cascode output stage. The
compensation network and emitter follower output buffer are in
the output stage. ꢀoltage feedback sets the gain, with the
AD8114 configured as a unity gain follower, and the AD8115
configured as a gain-of-2 amplifier with a feedback network.
Serial Programming
The serial programming mode uses the device pins , CLK,
CE
DATA IN,
, and
/PAR. The first step is to assert a
SER
UPDATE
low on
/PAR to enable the serial programming mode.
SER
CE
This architecture provides drive for a reverse-terminated video
load (150 Ω), with low differential gain and phase error for
relatively low power consumption. Power consumption is
further reduced by disabling outputs and transconductance
stages that are not in use. The user will notice a small increase
in input bias current as each transconductance stage is enabled.
for the chip must be low to allow data to be clocked into the
device. The signal can be used to address an individual
CE
device when devices are connected in parallel.
The signal should be high during the time that data is
UPDATE
shifted into the device’s serial port. Although the data will still
shift in when is low, the transparent, asynchronous
Features of the AD8114 and AD8115 simplify the construction
of larger switch matrices. The unused outputs of both devices
can be disabled to a high impedance state, allowing the outputs
of multiple ICs to be bused together. In the case of the AD8115,
a feedback isolation scheme is used so that the impedance of the
gain-of-2 feedback network does not load the output. Because
no additional input buffering is necessary, high input resistance
and low input capacitance are easily achieved without
additional signal degradation. To control enable glitches, it is
recommended that the disabled output voltage be maintained
within its normal enabled voltage range ( 3.3 ꢀ). If necessary,
the disabled output can be kept from drifting out of range by
applying an output load resistor to ground.
UPDATE
latches will allow the shifting data to reach the matrix. This will
cause the matrix to try to update to every intermediate state as
defined by the shifting data.
The data at DATA IN is clocked in at every down edge of CLK.
A total of 80 bits must be shifted in to complete the
programming. For each of the 16 outputs, there are four bits
(D0 to D3) that determine the source of its input followed by
one bit (D4) that determines the enabled state of the output. If
D4 is low (output disabled), the four associated bits (D0 to D3)
do not matter because no input will be switched to that output.
The most significant output address data is shifted in first, and
then following in sequence until the least significant output
A flexible TTL-compatible logic interface simplifies the
programming of the matrix. Both parallel and serial loading
into a first rank of latches programs each output. A global latch
simultaneously updates all outputs. A power-on reset pin is
available to avoid bus conflicts by disabling all outputs.
address data is shifted in. At this point
can be taken
UPDATE
low, which will cause the programming of the device according
to the data that was just shifted in. The registers are
UPDATE
is low (and
asynchronous, and when
are transparent.
is low), they
CE
UPDATE
Rev. B | Page 18 of 32
AD8114/AD8115
information that identifies the input that gets programmed to
the output that is addressed. The fourth data bit (D4) will
determine the enabled state of the output. If D4 is low (output
disabled), then the data on D0 to D3 does not matter.
If more than one AD8114/AD8115 device is to be serially
programmed in a system, the DATA OUT signal from one
device can be connected to the DATA IN of the next device to
form a serial chain. All of the CLK,
,
, and
CE UPDATE SER
/PAR pins should be connected in parallel and operated as
described above. The serial data is input to the DATA IN pin of
the first device of the chain, and it will ripple on through to the
last. Therefore, the data for the last device in the chain should
come at the beginning of the programming sequence. The
length of the programming sequence (80 bits) will be multiplied
by the number of devices in the chain.
After the desired address and data signals have been established,
they can be latched into the shift register by a high to low
transition of the CLK signal. The matrix will not be
programmed, however, until the
signal is taken low. It
UPDATE
is thus possible to latch in new data for several or all of the
outputs first via successive negative transitions of CLK while
is held high, and then have all the new data take effect
UPDATE
when UPDATE goes low. This technique should be used when
programming the device for the first time after power-up when
using parallel programming.
Parallel Programming
While using the parallel programming mode, it is not necessary
to reprogram the entire device when making changes to the
matrix. In fact, parallel programming allows the modification of
a single output at a time. Since this takes only one
POWER-ON RESET
When powering up the AD8114/AD8115, it is usually desirable
to have the outputs come up in the disabled state. When taken
CLK/
cycle, significant time savings can be realized by
UPDATE
using parallel programming.
low, the
pin will cause all outputs to be in the disabled
RESET
state. However, the
signal does not reset all registers in
RESET
One important consideration in using parallel programming is
that the
signal does not reset all registers in the
the AD8114/AD8115. This is important when operating in the
parallel programming mode. Please refer to that section for
information about programming internal registers after power-
up. Serial programming will program the entire matrix each
time, so no special considerations apply.
RESET
AD8114/AD8115. When taken low, the
signal will only
RESET
set each output to the disabled state. This is helpful during
power-up to ensure that two parallel outputs will not be active
at the same time.
Since the data in the shift register is random after power-up, it
should not be used to program the matrix, or the matrix can
enter unknown states. To prevent this, do not apply logic low
After initial power-up, the internal registers in the device will
generally have random data, even though the
signal was
RESET
asserted. If parallel programming is used to program one
output, then that output will be properly programmed, but the
rest of the device will have a random program state depending
on the internal register content at power-up. Therefore, when
using parallel programming, it is essential that all outputs be
programmed to a desired state after power-up. This will ensure
that the programming matrix is always in a known state. From
then on, parallel programming can be used to modify a single
output or more at a time.
signals to both
and
initially after power-up. The
CE
UPDATE
shift register should first be loaded with the desired data, and
then
The
can be taken low to program the device.
UPDATE
pin has a 20 kΩ pull-up resistor to DꢀDD that can
RESET
be used to create a simple power-up reset circuit. A capacitor
from to ground will hold low for some time
RESET
RESET
while the rest of the device stabilizes. The low condition will
cause all the outputs to be disabled. The capacitor will then
charge through the pull-up resistor to the high state, thus
allowing full programming capability of the device.
In similar fashion, if both
and
are taken low after
UPDATE
CE
initial power-up, the random power-up data in the shift register
will be programmed into the matrix. Therefore, to prevent the
crosspoint from being programmed into an unknown state, do
GAIN SELECTION
The 16 × 16 crosspoints come in two versions, depending on
the gain of the analog circuit paths that is desired. The AD8114
device is unity gain and can be used for analog logic switching
and other applications where unity gain is desired. The AD8114
can also be used for the input and interior sections of larger
crosspoint arrays where termination of output signals is not
usually used. The AD8114 outputs have very high impedance
when their outputs are disabled.
not apply low logic levels to both
and
after power
CE
UPDATE
is initially applied. Programming the full shift register one time
to a desired state by either serial or parallel programming after
initial power-up will eliminate the possibility of programming
the matrix to an unknown state.
To change an output’s programming via parallel programming,
/PAR and
SER
should be taken high and
should be
UPDATE
CE
taken low. The CLK signal should be in the high state. The 4-bit
address of the output to be programmed should be put on A0 to
A3. The first four data bits (D0 to D3) should contain the
The AD8115 can be used for devices that will be used to drive a
terminated cable with its outputs. This device has a built-in gain
Rev. B | Page 19 of 32
AD8114/AD8115
of 2 that eliminates the need for a gain-of-2 buffer to drive a
video line. Its high output disabled impedance minimizes signal
degradation when paralleling additional outputs.
architectures that can be constructed with fewer devices than
this minimum. These systems have connectivity available on a
statistical basis that is determined when designing the overall
system.
CREATING LARGER CROSSPOINT ARRAYS
The basic concept in constructing larger crosspoint arrays is to
connect inputs in parallel in a horizontal direction and to wire-
OR the outputs together in the vertical direction. The meaning
of horizontal and vertical can best be understood by looking at
a diagram. Figure 48 illustrates this concept for a 32 × 32
crosspoint array that uses four AD8114s or AD8115s.
The AD8114/AD8115 are high density building blocks for
creating crosspoint arrays of dimensions larger than 16 × 16.
ꢀarious features, such as output disable, chip enable, and gain-
of-1 and gain-of-2 options, are useful for creating larger arrays.
When required for customizing a crosspoint array size, they can
be used with the AD8108 and AD8109, a pair of (unity gain and
gain-of-2) 8 × 8 video crosspoint switches, or with the AD8110
and AD8111, a pair of (unity gain and gain-of-2) 16 × 8 video
crosspoint switches.
AD8114
OR
AD8114
OR
16
16
IN 00–15
16
AD8115
AD8115
R
TERM
The first consideration in constructing a larger crosspoint is to
determine the minimum number of devices required. The 16 ×
16 architecture of the AD8114/AD8115 contains 256 points,
which is a factor of 64 greater than a 4 × 1 crosspoint (or
multiplexer). The PC board area, power consumption, and
design effort savings are readily apparent when compared to
using these smaller devices.
16
16
AD8114
OR
AD8115
AD8114
OR
AD8115
16
16
IN 16–31
16
R
TERM
16
16
Figure 48. 32 × 32 Crosspoint Array Using AD8114 or Four AD8115s
For a nonblocking crosspoint, the number of points required is
the product of the number of inputs multiplied by the number
of outputs. Nonblocking requires that the programming of a
given input to one or more outputs does not restrict the
availability of that input to be a source for any other outputs.
The inputs are each uniquely assigned to each of the 32 inputs
of the two devices and terminated appropriately. The outputs
are wired-OR’ed together in pairs. The output from only one of
a wire-OR’ed pair should be enabled at any given time. The
device programming software must be properly written to cause
this to happen.
Some nonblocking crosspoint architectures will require more
than this minimum as calculated above. Also, there are blocking
Rev. B | Page 20 of 32
AD8114/AD8115
RANK 1
(8 × AD8114)
128:32
8
8
IN 00–15
IN 16–31
IN 32–47
IN 48–63
IN 64–79
IN 80–95
IN 96–111
AD8114
AD8114
AD8114
AD8114
AD8114
AD8114
AD8114
AD8114
16
16
16
16
16
16
16
R
R
R
R
R
R
R
TERM
TERM
TERM
TERM
TERM
TERM
TERM
8
8
8
8
RANK 2
32:16 NONBLOCKING
(32:32 BLOCKING)
8
8
8
8
8
1k
OUT 00Ð15
NONBLOCKING
Ω
AD8115
AD8115
8
8
8
1kΩ
8
1kΩ
8
ADDITIONAL
16 OUTPUTS
(SUBJECT
8
8
8
TO BLOCKING)
8
1kΩ
8
8
8
8
IN 112–127
16
R
TERM
Figure 49. Nonblocking 128 × 16 Array (128 × 32 Blocking)
composite video requires only one crosspoint channel per
system video channel. There are, however, other video formats
that can be routed with the AD8114/AD8115 requiring more
than one crosspoint channel per video channel.
Using additional crosspoint devices in the design can lower the
number of outputs that must be wire-OR’ed together. Figure 49
shows a block diagram of a system using eight AD8114s and
two AD8115s to create a nonblocking, gain-of-2, 128 × 16
crosspoint that restricts the wire-OR’ing at the output to only
four outputs.
Some systems use twisted-pair wiring to carry video signals.
These systems utilize differential signals and can lower costs
because they use lower cost cables, connectors and termination
methods. They also have the ability to lower crosstalk and reject
common-mode signals, which can be important for equipment
that operates in noisy environments or where common-mode
voltages are present between transmitting and receiving
equipment.
Additionally, by using the lower eight outputs from each of the
two Rank 2 AD8115s, a blocking 128 × 32 crosspoint array can
be realized. There are, however, some drawbacks to this
technique. The offset voltages of the various cascaded devices
will accumulate, and the bandwidth limitations of the devices
will compound. In addition, the extra devices will consume
more current and take up more board space. Once again, the
overall system design specifications will determine how to make
the various tradeoffs.
In such systems, the video signals are differential; there is a
positive and negative (or inverted) version of the signals. These
complementary signals are transmitted onto each of the two
wires of the twisted pair, yielding a first-order zero common-
mode voltage. At the receive end, the signals are differentially
received and converted back into a single-ended signal.
MULTICHANNEL VIDEO
The excellent video specifications of the AD8114/AD8115 make
them ideal candidates for creating composite video crosspoint
switches. These can be made quite dense by taking advantage of
the AD8114/AD8115’s high level of integration and the fact that
When switching these differential signals, two channels are
required in the switching element to handle the two differential
Rev. B | Page 21 of 32
AD8114/AD8115
signals that make up the video channel. Thus, one differential
video channel is assigned to a pair of crosspoint channels, both
input and output. For a single AD8114/AD8115, eight
differential video channels can be assigned to the 16 inputs and
16 outputs. This will effectively form an 8 × 8 differential
crosspoint switch.
Types of Crosstalk
Crosstalk can be propagated by means of any of three methods.
These fall into the categories of electric field, magnetic field,
and sharing of common impedances. This section will explain
these effects.
Every conductor can be both a radiator of electric fields and a
receiver of electric fields. The electric field crosstalk mechanism
occurs when the electric field created by the transmitter
propagates across a stray capacitance (e.g., free space) and
couples with the receiver and induces a voltage. This voltage is
an unwanted crosstalk signal in any channel that receives it.
Programming such a device will require that inputs and outputs
be programmed in pairs. This information can be deduced by
inspection of the programming format of the AD8114/AD8115
and the requirements of the system.
There are other analog video formats requiring more than one
analog circuit per video channel. One 2-circuit format that is
commonly being used in systems such as satellite Tꢀ, digital
cable boxes, and higher quality ꢀCRs is called S-video or Y/C
video. This format carries the brightness (luminance or Y)
portion of the video signal on one channel and the color
(chrominance, chroma, or C) on a second channel.
Currents flowing in conductors create magnetic fields that
circulate around the currents. These magnetic fields will then
generate voltages in any other conductors whose paths they
link. The undesired induced voltages in these other channels are
crosstalk signals. The channels that crosstalk can be said to have
a mutual inductance that couples signals from one channel to
another.
Since S-video also uses two separate circuits for one video
channel, creating a crosspoint system requires assigning one
video channel to two crosspoint channels, as in the case of a
differential video system. Aside from the nature of the video
format, other aspects of these two systems will be the same.
The power supplies, grounds, and other signal return paths of a
multichannel system are generally shared by the various
channels. When a current from one channel flows in one of
these paths, a voltage that is developed across the impedance
becomes an input crosstalk signal for other channels that share
the common impedance.
There are yet other video formats using three channels to carry
the video information. ꢀideo cameras produce RGB (red, green,
blue) directly from the image sensors. RGB is also the usual
format used by computers internally for graphics. RGB can be
converted to Y, R-Y, B-Y format, sometimes called YUꢀ format.
These 3-circuit video standards are referred to as component
analog video.
All these sources of crosstalk are vector quantities, so the
magnitudes cannot simply be added together to obtain the total
crosstalk. In fact, there are conditions where driving additional
circuits in parallel in a given configuration can actually reduce
the crosstalk.
The component video standards require three crosspoint
channels per video channel to handle the switching function. In
a fashion similar to the 2-circuit video formats, the inputs and
outputs are assigned in groups of three, and the appropriate
logic programming is performed to route the video signals.
Areas of Crosstalk
For a practical AD8114/AD8115 circuit, it is required that it be
mounted to some sort of circuit board to connect it to power
supplies and measurement equipment. Great care has been
taken to create a characterization board (also available as an
evaluation board) that adds minimum crosstalk to the intrinsic
device. This, however, raises the issue that a system’s crosstalk is
a combination of the intrinsic crosstalk of the devices in
addition to the circuit board to which they are mounted. It is
important to try to separate these two areas of crosstalk when
attempting to minimize its effect.
CROSSTALK
Many systems, such as broadcast video, that handle numerous
analog signal channels have strict requirements for keeping the
various signals from influencing any of the others in the system.
Crosstalk is the term used to describe the coupling of the
signals of other nearby channels to a given channel.
In addition, crosstalk can occur among the inputs to a
crosspoint and among the output. It can also occur from input
to output. Techniques will be discussed for diagnosing which
part of a system is contributing to crosstalk.
When there are many signals in close proximity in a system, as
will undoubtedly be the case in a system that uses the
AD8114/AD8115, the crosstalk issues can be quite complex. A
good understanding of the nature of crosstalk and some
definition of terms is required to specify a system that uses one
or more AD8114/AD8115s.
Rev. B | Page 22 of 32
AD8114/AD8115
Measuring Crosstalk
Obviously, some subset of all these cases must be selected to be
used as a guide for a practical measure of crosstalk. One
common method is to measure all hostile crosstalk. This term
means that the crosstalk to the selected channel is measured
while all other system channels are driven in parallel. In general,
this will yield the worst crosstalk number, but this is not always
the case due to the vector nature of the crosstalk signal.
Crosstalk is measured by applying a signal to one or more
channels and measuring the relative strength of that signal on a
desired selected channel. The measurement is usually expressed
as dB down from the magnitude of the test signal. The crosstalk
is expressed by
XT = 20 log10
Asel
(
s
)
Atest
(
s
)
Other useful crosstalk measurements are those created by one
nearest neighbor or by the two nearest neighbors on either side.
These crosstalk measurements will generally be higher than
those of more distant channels, so they can serve as a worst-case
measure for any other 1-channel or 2-channel crosstalk
measurements.
where s = jω is the Laplace transform variable, Asel(s) is the
amplitude of the crosstalk-induced signal in the selected
channel, and Atest(s) is the amplitude of the test signal. It can be
seen that crosstalk is a function of frequency, but not a function
of the magnitude of the test signal (to first order). In addition,
the crosstalk signal will have a phase relative to the test signal
associated with it.
Input and Output Crosstalk
The flexible programming capability of the AD8114/AD8115
can be used to diagnose whether crosstalk is occurring more on
the input side or the output side. Some examples are illustrative.
A given input channel (IN07 in the middle for this example)
can be programmed to drive OUT07 (also in the middle). The
input to IN07 is just terminated to ground (via 50 Ω or 75 Ω)
and no signal is applied.
A network analyzer is most commonly used to measure
crosstalk over a frequency range of interest. It can provide both
magnitude and phase information about the crosstalk signal.
As a crosspoint system or device grows larger, the number of
theoretical crosstalk combinations and permutations can
become extremely large. For example, in the case of the 16 × 16
matrix of the AD8114/AD8115, we can examine the number of
crosstalk terms that can be considered for a single channel, say
IN00 input. IN00 is programmed to connect to one of the
AD8114/AD8115 outputs where the measurement can be made.
All the other inputs are driven in parallel with the same test
signal (practically that is provided by a distribution amplifier),
with all other outputs except OUT07 disabled. Since grounded
IN07 is programmed to drive OUT07, no signal should be
present. Any signal that is present can be attributed to the other
15 hostile input signals because no other outputs are driven.
(They are all disabled.) Thus, this method measures the all-
hostile input contribution to crosstalk into IN07. Of course, the
method can be used for other input channels and combinations
of hostile inputs.
First, we can measure the crosstalk terms associated with
driving a test signal into each of the other 15 inputs one at a
time while applying no signal to IN00. We can then measure the
crosstalk terms associated with driving a parallel test signal into
all 15 other inputs taken two at a time in all possible
combinations, then three at a time, etc., until there is only one
way to drive a test signal into all 15 other inputs in parallel.
For output crosstalk measurement, a single input channel is
driven (IN00, for example) and all outputs other than a given
output (IN07 in the middle) are programmed to connect to
IN00. OUT07 is programmed to connect to IN15 (far away
from IN00), which is terminated to ground. Thus OUT07
should not have a signal present since it is listening to a quiet
input. Any signal measured at the OUT07 can be attributed to
the output crosstalk of the other 16 hostile outputs. Again, this
method can be modified to measure other channels and other
crosspoint matrix combinations.
Each of these cases is legitimately different from the others and
might yield a unique value depending on the resolution of the
measurement system, but it is hardly practical to measure all
these terms and then to specify them. In addition, this describes
the crosstalk matrix for just one input channel. A similar
crosstalk matrix can be proposed for every other input. In
addition, if the possible combinations and permutations for
connecting inputs to the other (not used for measurement)
outputs are taken into consideration, the numbers rather
quickly grow to astronomical proportions. If a larger crosspoint
array of multiple AD8114/AD8115s is constructed, the numbers
grow larger still.
Rev. B | Page 23 of 32
AD8114/AD8115
driven from a 75 Ω terminated cable, the input crosstalk can be
reduced by buffering this signal with a low output impedance
buffer.
Effect of Impedances on Crosstalk
The input side crosstalk can be influenced by the output
impedance of the sources that drive the inputs. The lower the
impedance of the drive source, the lower the magnitude of the
crosstalk. The dominant crosstalk mechanism on the input side
is capacitive coupling. The high impedance inputs do not have
significant current flow to create magnetically induced
crosstalk. However, significant current can flow through the
input termination resistors and the loops that drive them. Thus,
the PC board on the input side can contribute to magnetically
coupled crosstalk.
On the output side, the crosstalk can be reduced by driving a
lighter load. Although the AD8114/AD8115 is specified with
excellent differential gain and phase when driving a standard
150 Ω video load, the crosstalk will be higher than the
minimum obtainable due to the high output currents. These
currents will induce crosstalk via the mutual inductance of the
output pins and bond wires of the AD8114/AD8115.
From a circuit standpoint, this output crosstalk mechanism
looks like a transformer, with a mutual inductance between the
windings, that drives a load resistor. For low frequencies, the
magnitude of the crosstalk is given by
From a circuit standpoint, the input crosstalk mechanism looks
like a capacitor coupling to a resistive load. For low frequencies,
the magnitude of the crosstalk will be given by
XT = 20 log10
RS CM
× s
XT = 20 log10 (Mxy×s / RL )
where RS is the source resistance, CM is the mutual capacitance
between the test signal circuit and the selected circuit, and s is
the Laplace transform variable.
where Mxy is the mutual inductance of Output X to Output Y,
and RL is the load resistance on the measured output. This
crosstalk mechanism can be minimized by keeping the mutual
inductance low and increasing RL. The mutual inductance can
be kept low by increasing the spacing of the conductors and
minimizing their parallel length.
From the equation, it can be observed that this crosstalk
mechanism has a high-pass nature; it can be minimized by
reducing the coupling capacitance of the input circuits and
lowering the output impedance of the drivers. If the input is
Rev. B | Page 24 of 32
AD8114/AD8115
PCB LAYOUT
Extreme care must be exercised to minimize additional
crosstalk generated by the system circuit board(s). The areas
that must be carefully detailed are grounding, shielding, signal
routing, and supply bypassing.
Optimized for video applications, all signal inputs and outputs
are terminated with 75 Ω resistors. Stripline techniques are used
to achieve a characteristic impedance of 75 Ω on the signal
input and output lines. Figure 50 shows a cross section of one of
the input or output tracks along with the arrangement of the
PCB layers. It should be noted that unused regions of the four
layers are filled up with ground planes. As a result, the input
and output traces, in addition to having controlled impedances,
are well shielded.
The packaging of the AD8114/AD8115 is designed to help keep
the crosstalk to a minimum. Each input is separated from each
other input by an analog ground pin. All of these AGNDs
should be directly connected to the ground plane of the circuit
board. These ground pins provide shielding, low impedance
return paths, and physical separation for the inputs. All of these
help to reduce crosstalk.
w = 0.008"
(0.2mm)
TOP LAYER
t = 0.00135" (0.0343mm)
b = 0.0514"
(1.3mm)
a = 0.008"
(0.2mm)
Each output is separated from its two neighboring outputs by an
analog supply pin of one polarity or the other. Each of these
analog supply pins provides power to the output stages of only
the two nearest outputs. These supply pins provide shielding,
physical separation, and a low impedance supply for the
outputs. Individual bypassing of each of these supply pins with a
0.01 µF chip capacitor directly to the ground plane minimizes
high frequency output crosstalk via the mechanism of sharing
common impedances.
SIGNAL LAYER
POWER LAYER
BOTTOM LAYER
h = 0.025"
(0.63mm)
Figure 50. Cross Section of Input and Output Traces
The board has 32 BNC type connectors: 16 inputs and 16 outputs.
The connectors are arranged in a crescent around the device. As
can be seen from Figure 53, this results in all 16 input signal
traces and all 16 signal output traces having the same length.
This is useful in tests such as all-hostile crosstalk where the
phase relationship and delay between signals needs to be
maintained from input to output.
Each output also has an on-chip compensation capacitor that is
individually tied to the nearby analog ground pins AGND00
through AGND07. This technique reduces crosstalk by
preventing the currents that flow in these paths from sharing a
common impedance on the IC and in the package pins. These
AGNDxx signals should all be connected directly to the ground
plane.
The three power supply pins AꢀCC, DꢀCC and AꢀEE should
be connected to good quality, low noise, 5 ꢀ supplies. Where
the same 5 ꢀ power supplies are used for analog and digital,
separate cables should be run for the power supply to the
evaluation board’s analog and digital power supply pins.
The input and output signals will have minimum crosstalk if
they are located between ground planes on layers above and
below, and separated by ground in between. ꢀias should be
located as close to the IC as possible to carry the inputs and
outputs to the inner layer. The only place the input and output
signals surface is at the input termination resistors and the
output series back-termination resistors. These signals should
also be separated, to the extent possible, as soon as they emerge
from the IC package.
As a general rule, each power supply pin (or group of adjacent
power supply pins) should be locally decoupled with a 0.01 µF
capacitor. If there is a space constraint, it is more important to
decouple analog power supply pins before digital power supply
pins. A 0.1 µF capacitor, located reasonably close to the pins,
can be used to decouple a number of power supply pins. Finally
a 10 µF capacitor should be used to decouple power supplies as
they come onto the board.
Rev. B | Page 25 of 32
AD8114/AD8115
Figure 51. Component Side Silkscreen
Figure 52. Board Layout (Component Side)
Rev. B | Page 26 of 32
AD8114/AD8115
Figure 53. Board Layout (Signal Layer)
Figure 54. Board Layout (Ground Plane)
Rev. B | Page 27 of 32
AD8114/AD8115
Figure 55. Board Layout (Circuit Side)
Figure 56. Circuit Side Silkscreen
Rev. B | Page 28 of 32
AD8114/AD8115
EVALUATION BOARD
DVCC DGND NC AVEE AGND AVCC NC
P1-7
P1-1 P1-2
+
P1-3 P1-4
P1-5 P1-6
+
DVCC
0.01µF
AVCC
0.01µF
AVEE
0.01µF
JUMPER
+
0.1µF 10µF
0.1µF 10µF
1, 75
DVCC
21, 55
AVCC
20, 56
AVEE
0.1µF 10µF
NO CONNECT:
85–93
AVCC
58
54
53
INPUT 00
INPUT 00
AGND
AVCC
OUTPUT 00
OUTPUT 01
OUTPUT 02
OUTPUT 03
OUTPUT 04
OUTPUT 05
OUTPUT 06
OUTPUT 07
OUTPUT 08
OUTPUT 09
OUTPUT 10
OUTPUT 11
OUTPUT 12
OUTPUT 13
OUTPUT 14
OUTPUT 15
57,59
0.01µF
0.01µF
0.01µF
0.01µF
0.01µF
0.01µF
0.01µF
0.01µF
0.01µF
0.01µF
0.01µF
0.01µF
0.01µF
0.01µF
0.01µF
0.01µF
75Ω
75Ω
75Ω
75Ω
75Ω
75Ω
75Ω
75Ω
75Ω
75Ω
75Ω
75Ω
75Ω
75Ω
75Ω
75Ω
75Ω
OUTPUT 00
60
61
AV
EE
INPUT 01
INPUT 02
INPUT 03
INPUT 04
INPUT 05
INPUT 06
INPUT 07
INPUT 08
INPUT 09
INPUT 10
INPUT 11
INPUT 12
INPUT 13
INPUT 14
INPUT 15
INPUT 01
AGND
52
51
AVEE
75Ω
OUTPUT 01
62
63
AVCC
75Ω
INPUT 02
AGND
50
49
AVCC
OUTPUT 02
64
65
INPUT 03
AGND
AV
EE
48
47
AVEE
75Ω
OUTPUT 03
66
67
INPUT 04
AGND
AVCC
75Ω
46
45
AVCC
68
69
OUTPUT 04
INPUT 05
AGND
AV
EE
44
43
AVEE
70
71
75Ω
INPUT 06
AGND
OUTPUT 05
AVCC
75Ω
42
41
AVCC
72
INPUT 07
AGND
OUTPUT 06
3,73
AV
EE
40
39
AVEE
4
5
INPUT 08
AGND
AD8114/AD8115
75Ω
OUTPUT 07
AVCC
75Ω
38
37
6
7
AVCC
INPUT 09
AGND
OUTPUT 08
AV
EE
8
9
36
35
INPUT 10
AGND
AVEE
75Ω
OUTPUT 09
10
11
AVCC
75Ω
INPUT 11
AGND
34
33
AVCC
OUTPUT 10
12
13
AV
INPUT 12
AGND
EE
32
31
AVEE
75Ω
OUTPUT 11
14
15
INPUT 13
AGND
AVCC
75Ω
30
29
AVCC
16
17
OUTPUT 12
INPUT 14
AGND
AV
EE
28
27
AVEE
75Ω
18
19
OUTPUT 13
INPUT 15
AGND
AVCC
75Ω
26
25
AVCC
98
96
DATA OUT
DATA IN
OUTPUT 14
R
AV
EE
24
23
AVEE
75Ω
OUTPUT 15
R
AVCC 22
P2-5
P2-4
P2-2
P2-3
P2-1
P2-6
2,74 100 99 97
95 84 83 82 81 80 79 78 77 76 94
R
R33
20kΩ
R
C
DVCC
R
R
R
R
R
R
R
R
R
R
R
R
SERIAL MODE
JUMP
NOTES
R = OPTIONAL 50
C = OPTIONAL SMOOTHING CAPACITOR
Ω
TERMINATOR RESISTORS
Figure 57. Evaluation Board Schematic
Rev. B | Page 29 of 32
AD8114/AD8115
MOLEX 0.100" CENTER
CRIMP TERMINAL HOUSING
CONTROL THE EVALUATION BOARD FROM A PC
D-SUB 25 PIN (MALE)
RESET
The evaluation board includes Windows®-based control
software and a custom cable that connects the board’s digital
interface to the printer port of the PC. The wiring of this cable
is shown in Figure 58. The software requires Windows 3.1 or
later to operate. To install the software, insert the disk labeled
Disk 1 of 2 into the PC and run the file called SETUP.EXE.
Additional installation instructions will be given on-screen.
Before beginning installation, it is important to terminate any
other Windows applications that are running.
1
1
14
CLK
CE
UPDATE
DATA IN
DGND
6
MOLEX
TERMINAL HOUSING
D-SUB-25
SIGNAL
2
3
3
1
CE
RESET
25
13
4
5
6
25
4
5
2
6
UPDATE
DATA IN
CLK
When you launch the crosspoint control software, you will be
asked to select the printer port. Most modern PCs have only
one printer port, usually called LPT1. However some laptop
computers use the PRN port.
DGND
EVALUATION BOARD
PC
Figure 58. Evaluation Board-PC Connection Cable
Figure 59 shows the main screen of the control software in its
initial reset state (all outputs off). Using the mouse, any input
can be connected with one or more outputs by simply clicking
on the appropriate radio buttons in the 16 × 16 on-screen array.
Each time a button is clicked on, the software automatically
sends and latches the required 80-bit data stream to the
evaluation board. An output can be turned off by clicking the
appropriate button in the off column. To turn off all outputs,
OVERSHOOT OF PC PRINTER PORTS’ DATA LINES
The data lines on some printer ports have excessive overshoot.
Overshoot on the pin that is used as the serial clock (Pin 6 on
the D-Sub-25 connector) can cause communication problems.
This overshoot can be eliminated by connecting a capacitor
from the CLK line on the evaluation board to ground. A pad
has been provided on the circuit side (C33) of the evaluation
board to allow this capacitor to be soldered into place.
Depending on the overshoot from the printer port, this
capacitor may need to be as large as 0.01 µF.
click on
.
RESET
While the computer software only supports serial programming
via a PC’s parallel port and the provided cable, the evaluation
board has a connector that can be used for parallel
AD8114/AD8115
Parallel Port Selection
programming. The
/PAR signal should be at a logic high to
SER
use parallel programming. There is no cable or software
provided with the evaluation board for parallel programming.
These are left to the user to provide.
The software offers volatile and nonvolatile storage of
configurations. For volatile storage, up to two configurations
can be stored and recalled using the Memory 1 and Memory 2
buffers. These function in a fashion identical to the memory on
a pocket calculator. For nonvolatile storage of a configuration,
the save setup and load setup functions can be used. This stores
the configuration as a data file on disk.
Figure 59. Screen Display and Control Software
Rev. B | Page 30 of 32
AD8114/AD8115
OUTLINE DIMENSIONS
16.00
BSC SQ
1.60 MAX
0.75
0.60
0.45
100
1
76
75
PIN 1
14.00
BSC SQ
TOP VIEW
(PINS DOWN)
1.45
1.40
1.35
0.20
0.09
7°
3.5°
0°
0.08 MAX
COPLANARITY
25
51
50
0.15
0.05
26
SEATING
PLANE
0.27
0.22
0.17
VIEW A
0.50
BSC
LEAD PITCH
VIEW A
ROTATED 90° CCW
COMPLIANT TO JEDEC STANDARDS MS-026-BED
Figure 60. 100-Lead Low Profile Quad Flat Package [LQFP]
(ST-100)
Dimension shown in millimeters
ORDERING GUIDE1
Model
AD8114AST
AD8114ASTZ2
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
Package Option
ST-100
ST-100
ST-100
ST-100
100-Lead Low Profile Quad Flat Package [LQFP]
100-Lead Low Profile Quad Flat Package [LQFP]
100-Lead Low Profile Quad Flat Package [LQFP]
100-Lead Low Profile Quad Flat Package [LQFP]
Evaluation Board
AD8115AST
AD8115ASTZ2
AD8114-EVAL
AD8115-EVAL
Evaluation Board
1 Details of the lead finish composition can be found on the ADI website at www.analog.com by reviewing the Material Description of each relevant package.
2 Z = Pb-free part.
Rev. B | Page 31 of 32
AD8114/AD8115
NOTES
©
2005 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C01070–0–9/05(B)
Rev. B | Page 32 of 32
相关型号:
©2020 ICPDF网 联系我们和版权申明