AD8153ACPZ [ADI]
3.2 Gbps Single Buffered Mux/Demux Switch; 3.2 Gbps的一个缓冲器，复用器/解复用器开关
| 型号： | AD8153ACPZ |
| 厂家： | 
ADI |
| 描述： | 3.2 Gbps Single Buffered Mux/Demux Switch |
| 文件： | 总24页 (文件大小：719K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
3.2 Gbps
Single Buffered Mux/Demux Switch
AD8153
FEATURES
FUNCTIONAL BLOCK DIAGRAM
Single lane 2:1 mux/1:2 demux
3.2 Gbps to dc data rates
TRANSMIT
PRE-EMPHASIS
RECEIVE
EQUALIZATION
Compensates over 40 inches of FR4 at 3.2 Gbps through
Two levels of input equalization, or
Four levels of output pre-emphasis
Operates with ac- or dc-coupled differential I/O
Low deterministic jitter, typically 16 ps p-p
Low random jitter, typically 500 fs rms
On-chip terminations
INPUT A
INPUT B
EQ
EQ
OUTPUT C
RECEIVE
EQUALIZATION
OUTPUT A
OUTPUT B
INPUT C
EQ
Unicast or bicast on 1:2 demux function
Loopback capability on all ports
3.3 V core supply
Flexible I/O supply
Low power, typically 200 mW in basic configuration1
32-lead LFCSP package
SEL
2:1 MULTIPLEXER/
1:2 DEMULTIPLEXER
TRANSMIT
PRE-EMPHASIS
BICAST
LB_A
LB_B
LB_C
CONTROL
LOGIC
MODE
RESETB
EQ_A/(SCL)
EQ_B/(SDA)
EQ_C
AD8153
PE_A/(I2C_A[0])
PE_B/(I2C_A[1])
PE_C/(I2C_A[2])
−40°C to +85°C operating temperature range
APPLICATIONS
Figure 1.
Low cost redundancy switch
SONET OC48/SDH16 and lower data rates
Gigabit Ethernet over backplane
Fibre Channel 1.06 Gbps and 2.12 Gbps over backplane
Serial RapidIO
PCI Express Gen 1
Infiniband over backplane
provide access to advanced features, such as additional pre-
emphasis settings and output disable. In mixed mode, the user
accesses the advanced features using I2C, but controls lane
switching using the external pins.
GENERAL DESCRIPTION
The AD8153 is an asynchronous, protocol agnostic, single-lane
2:1 switch with three differential CML inputs and three differential
CML outputs. The AD8159, another member of the Xstream
line of products, is suitable for similar applications that require
more than one lane.
The main application of the AD8153 is to support redundancy
on both the backplane side and the line interface side of a serial
link. The device has unicast and bicast capability, so it is capable
of supporting either 1 + 1 or 1:1 redundancy.
The AD8153 is optimized for NRZ signaling with data rates of
up to 3.2 Gbps per port. Each port offers two levels of input
equalization and four levels of output pre-emphasis.
Using a mixture of bicast and loopback modes, the AD8153 can
also be used to test high speed serial links by duplicating the
incoming data and transmitting it to the destination port and
test equipment simultaneously.
The device consists of a 2:1 multiplexer and a 1:2 demultiplexer.
There are three operating modes: pin mode, serial mode, and
mixed mode. In pin mode, lane switching, equalization, and
pre-emphasis are controlled exclusively using external pins. In
serial mode, an I2C interface is used to control the device and to
1
Two ports active with no pre-emphasis.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2007 Analog Devices, Inc. All rights reserved.
AD8153
TABLE OF CONTENTS
Features .............................................................................................. 1
Transmit Pre-Emphasis ............................................................. 14
I2C Serial Control Interface........................................................... 15
Register Set.................................................................................. 15
General Functionality................................................................ 15
I2C Data Write............................................................................. 16
I2C Data Read.............................................................................. 17
Applications Information.............................................................. 18
PCB Design Guidelines ................................................................. 19
Interfacing to the AD8153............................................................. 20
Termination Structures.............................................................. 20
Input Compliance....................................................................... 20
Output Compliance ................................................................... 21
Outline Dimensions....................................................................... 22
Ordering Guide .......................................................................... 22
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description......................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
I2C Timing Specifications............................................................ 4
Absolute Maximum Ratings............................................................ 5
ESD Caution.................................................................................. 5
Pin Configuration and Function Descriptions............................. 6
Typical Performance Characteristics ............................................. 7
Theory of Operation ...................................................................... 13
Switch Configurations ............................................................... 13
Receive Equalization .................................................................. 14
REVISION HISTORY
4/07—Revision 0: Initial Version.
Rev. 0 | Page 2 of 24
AD8153
SPECIFICATIONS
VCC = VTTI = VTTO = 3.3 V, VEE = 0 V, RL = 50 Ω, two outputs active with no pre-emphasis, data rate = 3.2 Gbps, ac-coupled, PRBS7 test
pattern, VID = 800 mV p-p, TA = 25°C, unless otherwise noted.1
Table 1.
Parameter
Conditions
Min
Typ
Max
Unit
DYNAMIC PERFORMANCE
Data Rate/Channel (NRZ)
Deterministic Jitter
Random Jitter
Propagation Delay
Lane-to-Lane Skew
Switching Time
DC
3.2
Gbps
ps p-p
fs
ps
ps
Data rate = 3.2 Gbps, high EQ
RMS, high EQ
Input to output
16
500
640
55
5
ns
Output Rise/Fall Time
INPUT CHARACTERISTICS
Input Voltage Swing
Input Voltage Range
Input Capacitance
20% to 80%
85
ps
Differential
Common mode, VID = 800 mV p-p
200
VEE + 1.0
2000
VCC + 0.3
mV p-p
V
pF
2
OUTPUT CHARACTERISTICS
Output Voltage Swing
Output Voltage Range
Output Current
Differential, @ dc
Single-ended absolute voltage level
No pre-emphasis
700
Vcc − 1.6
800
900
Vcc + 0.6
mV p-p
V
mA
mA
pF
16
28
2
Output Current
Maximum pre-emphasis, all ports
Output Capacitance
TERMINATION CHARACTERISTICS
Resistance
Differential
100
0.1
Ω
Ω/°C
Temperature Coefficient
POWER SUPPLY
Operating Range
VCC
VTTI
VTTO
VEE = 0 V
VEE = 0 V
VEE = 0 V
3.0
3.3
VCC
VCC
3.6
V
V
V
Supply Current
ICC
II/O = ITTO + ITTI
Two outputs active, no pre-emphasis, 400 mV I/O swings
(800 mV p-p differential)
27
26
31
32
35
39
mA
mA
Supply Current
ICC
II/O = ITTO + ITTI
Three outputs active, maximum pre-emphasis, 400 mV
I/O swings (800 mV p-p differential)
53
74
58
84
63
95
mA
mA
THERMAL CHARACTERISTICS
Operating Temperature Range
θJA
−40
+85
°C
°C/W
Still air
30.0
LOGIC INPUT CHARACTERISTICS
Input High (VIH)
Input Low (VIL)
2.4
VEE
VCC
0.8
V
V
1 VID: Input differential voltage swing.
Rev. 0 | Page 3 of 24
AD8153
I2C TIMING SPECIFICATIONS
SDA
t
t
t
t
t
BUF
r
t
HD;STA
SP
f
SU;DAT
t
f
tLOW
t
r
SCL
t
t
SU;STO
t
HD;STA
SU;STA
t
t
HIGH
HD;DAT
S
Sr
P
S
Figure 2. I2C Timing Diagram
Table 2.
Parameter
SCL Clock Frequency
Hold Time for a Start Condition
Set-up Time for a Repeated Start Condition
Low Period of the SCL Clock
High Period of the SCL Clock
Data Hold Time
Symbol
fSCL
Min
0
Max
Unit
kHz
μs
μs
μs
μs
μs
ns
ns
ns
μs
ns
pF
400+
–
–
–
–
–
–
300
300
–
–
7
tHD;STA
tSU;STA
tLOW
tHIGH
tHD;DAT
tSU;DAT
tr
0.6
0.6
1.3
0.6
0
10
1
1
Data Set-Up Time
Rise Time for Both SDA and SCL
Fall Time for Both SDA and SCL
Set-Up Time for Stop Condition
Bus Free Time Between a Stop Condition and a Start Condition
Capacitance for Each I/O Pin
tf
tSU;STO
tBUF
Ci
0.6
1
5
Rev. 0 | Page 4 of 24
AD8153
ABSOLUTE MAXIMUM RATINGS
Table 3.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Parameter
Rating
VCC to VEE
3.7 V
VTTI
VCC + 0.6 V
VTTO
VCC + 0.6 V
Internal Power Dissipation
Differential Input Voltage
Logic Input Voltage
Storage Temperature Range
Lead Temperature
Junction Temperature
4.1 W
2.0 V
VEE − 0.3V < VIN < VCC + 0.6 V
−65°C to +125°C
300°C
ESD CAUTION
150°C
Rev. 0 | Page 5 of 24
AD8153
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
VCC
VTTO
ONA
OPA
VTTI
INA
1
2
3
4
5
6
7
8
24 MODE
23 RESETB
22 SEL
21 BICAST
20 LB_A
19 LB_B
18 LB_C
17 EQ_A/(SCL)
PIN 1
INDICATOR
AD8153
TOP VIEW
IPA
VEE
NOTE
EPAD NEEDS TO BE ELECTRICALLY
CONNECTED TO VEE.
Figure 3. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
Mnemonic
Type
Power
Power
I/O
Description
1, 9, 12
2
3
4
VCC
VTTO
ONA
OPA
Positive Supply.
Output Termination Supply.
High Speed Output Complement.
High Speed Output.
I/O
5
6
7
VTTI
INA
IPA
Power
I/O
I/O
Input Termination Supply.
High Speed Input Complement.
High Speed Input.
8, 32, EPAD
10
11
VEE
ONB
OPB
Power
I/O
I/O
Negative Supply.
High Speed Output Complement.
High Speed Output.
13
14
INB
IPB
I/O
I/O
High Speed Input Complement.
High Speed Input.
15
16
17
18
19
20
21
22
23
24
25
26
27
28
EQ_C
Control
Control
Control
Control
Control
Control
Control
Control
Control
Control
Control
Control
I/O
Port C Input Equalization Control.
Port B Input Equalization Control/(I2C Data when MODE = 1).
Port A Input Equalization Control/(I2C Clock when MODE = 1).
Port C Loopback Enable.
Port B Loopback Enable.
Port A Loopback Enable.
EQ_B/(SDA)
EQ_A/(SCL)
LB_C
LB_B
LB_A
BICAST
SEL
Bicast Enable.
A/B Select.
RESETB
MODE
PE_C/(I2C_A[2])
PE_B/(I2C_A[1])
ONC
Configuration Registers Reset.
Configuration Mode. 1 for Serial/Mixed Mode, 0 for Pin Mode.
Port C Pre-Emphasis Control/(I2C Slave Address Bit 2 when MODE = 1).
Port B Pre-Emphasis Control/(I2C Slave Address Bit 1 when MODE = 1).
High Speed Output Complement.
High Speed Output.
OPC
I/O
29
30
31
PE_A/(I2C_A[0])
INC
IPC
Control
I/O
I/O
Port A Pre-Emphasis Control/(I2C Slave Address Bit 0 when MODE = 1).
High Speed Input Complement.
High Speed Output.
Rev. 0 | Page 6 of 24
AD8153
TYPICAL PERFORMANCE CHARACTERISTICS
VCC = VTTI = VTTO =3.3 V, VEE = 0 V, RL = 50 Ω, two outputs active with no pre-emphasis, high EQ, data rate = 3.2 Gbps, ac-coupled,
PRBS7 test pattern, VID = 800 mV p-p, TA = 25°C, unless otherwise noted.
50Ω CABLES
50Ω CABLES
2
2
2
2
INPUT
PIN
OUTPUT
PIN
DATA OUT
50Ω
HIGH-SPEED
SAMPLING
AD8153
AC COUPLED
EVALUATION
BOARD
PATTERN
GENERATOR
TP1
TP2
OSCILLOSCOPE
Figure 4. Standard Test Circuit (No Channel)
40ps/DIV
40ps/DIV
Figure 6. 3.2 Gbps Output Eye, No Channel
(TP2 from Figure 4)
Figure 5. 3.2 Gbps Input Eye
(TP1 from Figure 4)
Rev. 0 | Page 7 of 24
AD8153
50Ω CABLES
50Ω CABLES
50Ω CABLES
2
2
2
2
2
2
INPUT OUTPUT
PIN PIN
DATA OUT
FR4 TEST BACKPLANE
50Ω
HIGH-
SPEED
SAMPLING
OSCILLOSCOPE
DIFFERENTIAL
STRIPLINE TRACES
8mils WIDE, 8mils SPACE,
8mils DIELECTRIC HEIGHT
TRACE LENGTHS = 20 INCHES,
40 INCHES
AD8153
AC COUPLED
EVALUATION
BOARD
PATTERN
GENERATOR
TP1
TP2
TP3
40ps/DIV
REFERENCE EYE DIAGRAM AT TP1
Figure 7. Input Equalization Test Circuit
40ps/DIV
40ps/DIV
Figure 10. 3.2 Gbps Output Eye, 20 Inch FR4 Input Channel, High EQ
(TP3 from Figure 7)
Figure 8. 3.2 Gbps Input Eye, 20 Inch FR4 Input Channel
(TP2 from Figure 7)
40ps/DIV
40ps/DIV
Figure 11. 3.2 Gbps Output Eye, 40 Inch FR4 Input Channel, High EQ
(TP3 from Figure 7)
Figure 9. 3.2 Gbps Input Eye, 40 Inch FR4 Input Channel
(TP2 from Figure 7)
Rev. 0 | Page 8 of 24
AD8153
50Ω CABLES
50Ω CABLES
50Ω CABLES
2
2
2
2
2
2
INPUT OUTPUT
PIN PIN
DATA OUT
FR4 TEST BACKPLANE
50Ω
HIGH-
SPEED
SAMPLING
OSCILLOSCOPE
DIFFERENTIAL
STRIPLINE TRACES
8mils WIDE, 8mils SPACE,
8mils DIELECTRIC HEIGHT
TRACE LENGTHS = 20 INCHES,
40 INCHES
AD8153
AC COUPLED
EVALUATION
BOARD
PATTERN
GENERATOR
TP1
TP2
TP3
40ps/DIV
REFERENCE EYE DIAGRAM AT TP1
Figure 12. Output Pre-Emphasis Test Circuit
40ps/DIV
40ps/DIV
Figure 15. 3.2 Gbps Output Eye, 20 Inch FR4 Output Channel, PE = 2
(TP3 from Figure 12)
Figure 13. 3.2 Gbps Output Eye, Pre-Channel, PE = 2
(TP2 from Figure 12)
40ps/DIV
40ps/DIV
Figure 14. 3.2 Gbps Output Eye, Pre-Channel, PE = 3
(TP2 from Figure 12)
Figure 16. 3.2 Gbps Output Eye, 40 Inch FR4 Output Channel, PE = 3
(TP3 from Figure 12)
Rev. 0 | Page 9 of 24
AD8153
80
70
60
50
40
30
20
10
80
70
60
50
40
30
20
10
0
PE = 1
PE = 0
PE = 2
LOW EQ
PE = 3
HIGH EQ
0
0
10
20
30
40
0
10
20
30
40
FR4 INPUT CHANNEL LENGTH (IN)
FR4 OUTPUT CHANNEL LENGTH (IN)
Figure 17. Deterministic Jitter vs. FR4 Input Channel Length
Figure 20. Deterministic Jitter vs. FR4 Output Channel Length
80
20
15
10
SAMPLES: 557k
70
60
50
40
30
20
10
DETERMINISTIC JITTER
5
0
RANDOM JITTER
2.5
0
1.0
1.5
2.0
3.0
3.5
4.0
–2ps
–1ps
0.0s
1ps
2ps
DATA RATE (Gbps)
Figure 18. Jitter vs. Data Rate
Figure 21. Random Jitter Histogram, 3.2 Gbps
80
70
60
50
40
30
20
10
80
70
60
50
40
30
20
10
DETERMINISTIC JITTER
RANDOM JITTER
DETERMINISTIC JITTER
RANDOM JITTER
0
0
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
0.8
1.3
1.8
2.3
2.8
3.3
3.8
DIFFERENTIAL INPUT SWING (V)
INPUT COMMON-MODE VOLTAGE (V)
Figure 19. Jitter vs. Differential Input Swing
Figure 22. Jitter vs. Input Common-Mode Voltage
Rev. 0 | Page 10 of 24
AD8153
80
70
60
50
40
30
20
10
80
70
60
50
40
30
20
10
0
DETERMINISTIC JITTER
RANDOM JITTER
DETERMINISTIC JITTER
RANDOM JITTER
0
3.0
3.1
3.2
3.3
(V)
3.4
3.5
3.6
2
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.6
V
VTTO (V)
CC
Figure 26. Jitter vs. Output Termination Voltage
Figure 23. Jitter vs. Core Supply Voltage
100
95
90
85
80
75
80
70
60
50
40
30
20
10
DETERMINISTIC JITTER
RANDOM JITTER
0
–40
–20
0
20
40
60
80
100
–40
–20
0
20
40
60
80
100
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 27. Rise/Fall Time vs. Temperature
Figure 24. Jitter vs. Temperature
700
650
600
700
650
600
550
500
550
500
–40
–20
0
20
40
60
80
100
3.0
3.1
3.2
3.3
(V)
3.4
3.5
3.6
TEMPERATURE (°C)
V
CC
Figure 25. Propagation Delay vs. Core Supply Voltage
Figure 28. Propagation Delay vs. Temperature
Rev. 0 | Page 11 of 24
AD8153
1000
1000
900
900
800
800
700
600
500
400
300
200
100
700
600
500
400
300
200
100
0
0
3.0
3.1
3.2
3.3
(V)
3.4
3.5
3.6
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
V
DATA RATE (Gbps)
CC
Figure 30. Eye Height vs. Data Rate
Figure 29. Eye Height vs. Core Supply Voltage
Rev. 0 | Page 12 of 24
AD8153
THEORY OF OPERATION
The AD8153 consists of a 2:1 multiplexer and a 1:2 demultiplexer.
There are three operating modes: pin mode, serial mode, and
mixed mode. In pin mode, lane switching, equalization, and
pre-emphasis are controlled using external pins. In serial mode,
an I2C interface is used to control the device and to provide
access to advanced features, such as additional pre-emphasis
settings and output disable. In mixed mode, the user accesses
the advanced features using I2C but controls lane switching
using external pins.
side, the device relays received data on either Input Port A or Input
Port B to Output Port C, depending on the state of the SEL bit.
When bicast mode is off, the outputs of either Port A or Port B
are in an idle state. In the idle state, the output tail current is set
to 0, and the P and N sides of the lane are pulled up to the output
termination voltage through the on-chip termination resistors.
The device also supports loopback on all ports, illustrated in
Figure 31. Enabling loopback on any port overrides configurations
set by the BICAST and SEL control bits. Table 5 summarizes the
possible switch configurations.
SWITCH CONFIGURATIONS
On the demultiplexer side, the AD8153 relays received data on
Input Port C to Output Port A and/or Output Port B, depending
on the state of the BICAST and SEL bits. On the multiplexer
The AD8153 output disable feature can be used to force an
output into the idle (powered-down) state. This feature is only
accessible through the serial control interface.
OUTPUT A
1:2 DEMUX
INPUT C
PORT C LOOPLOCK
OUTPUT C
OUTPUT B
PORT A LOOPBACK
PORT B LOOPBACK
INPUT A
INPUT B
2:1 MUX
Figure 31. Loopback Configurations
Table 5. Switch Configurations
LB_A
LB_B
LB_C
SEL
0
0
1
1
0
X
1
0
1
1
0
1
X
0
0
1
0
BICAST
Output A
Output B
Idle
Input C
Input C
Input C
Idle
Input C
Input C
Input B
Input B
Input B
Input B
Input B
Input B
Idle
Output C
Input A
Input A
Input B
Input B
Input C
Input C
Input C
Input A
Input B
Input B
Input C
Input C
Input C
Input A
Input A
Input B
Input C
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
0
1
1
1
0
0
0
1
1
1
0
0
0
0
1
0
1
0
1
0
X
0
1
X
0
1
0
1
X
0
Input C
Input C
Idle
Input C
Input C
Input C
Idle
Input C
Idle
Input C
Input C
Idle
Input C
Input A
Input A
Input A
Input A
Input C
Input C
Idle
0
1
Rev. 0 | Page 13 of 24
AD8153
LB_A
LB_B
LB_C
SEL
X
1
0
1
BICAST
Output A
Input A
Input A
Input A
Input A
Input A
Output B
Input C
Input C
Input B
Input B
Input B
Output C
Input C
Input C
Input A
Input B
Input C
1
1
1
1
1
0
0
1
1
1
1
1
0
0
1
1
X
X
X
X
X
RECEIVE EQUALIZATION
TRANSMIT PRE-EMPHASIS
In backplane applications, the AD8153 needs to compensate for
signal degradation caused by long traces. The device supports
two levels of input equalization, configured on a per-port basis.
Table 6 summarizes the high-frequency asymptotic gain boost
for each setting.
Transmitter pre-emphasis levels can be set by pin control or
through the control registers when using the I2C interface. Pin
control allows two settings of PE. The control registers provide
two additional settings.
Table 7. Pre-Emphasis Settings
Table 6. Receive Equalization Settings
Serial Mode
Pin Mode
EQ_A/B/C
EQ Boost
PE_A/B/C Setting PE_A/B/C PE Boost (%) PE Boost (dB)
0
1
6 dB
12 dB
0
1
2
3
0
0
0
N/A
1
25
50
75
1.9
3.5
4.9
N/A
Rev. 0 | Page 14 of 24
AD8153
I2C SERIAL CONTROL INTERFACE
pins or the internal register set. The source of the control is
REGISTER SET
selected using the mask bits (Register 0x00). If a mask bit is set
to 0, the external pin acts as the source for that specific control.
If a mask bit is set to 1, the associated internal register acts as
the source for that specific control. As an example, if Register 0x00
were set to the value 0x0C, the SEL and LB_C controls would
come from the internal register set (Bit 0 of Register 0x04 and Bit
3 of Register 0x03, respectively), and the BICAST, LB_A, and
LB_B controls would come from the external pins.
The AD8153 can be controlled in one of three modes: pin
mode, serial mode, and mixed mode. In pin mode, the AD8153
control is derived from the package pins, whereas in serial
mode a set of internal registers controls the AD8153. There is
also a mixed mode where switching is controlled via external
pins, and equalization and pre-emphasis are controlled via the
internal registers. The methods for writing data to and reading
data from the AD8153 are described in the I2C Data Write
section and the I2C Data Read section.
GENERAL FUNCTIONALITY
The mode is controlled via the MODE pin. To set the part in
pin mode, MODE should be driven low to VEE. When MODE
is driven high to VCC, the part is set to serial or mixed mode.
The AD8153 register set is controlled through a 2-wire I2C
interface. The AD8153 acts only as an I2C slave device. Therefore,
the I2C bus in the system needs to include an I2C master to
configure the AD8153 and other I2C devices that may be on the
bus. When the MODE pin is set to a Logic 1, data transfers are
controlled through the use of the two I2C wires: the input clock
pin, SCL, and the bidirectional data pin, SDA.
The AD8153 I2C interface can be run in the standard (100 kHz)
and fast (400 kHz) modes. The SDA line only changes value
when the SCL pin is low with two exceptions. To indicate the
beginning or continuation of a transfer, the SDA pin is driven
low while the SCL pin is high, and to indicate the end of a
transfer, the SDA line is driven high while the SCL line is high.
Therefore, it is important to control the SCL clock to only
toggle when the SDA line is stable unless indicating a start,
repeated start, or stop condition.
In pin mode, all controls are derived from the external pins. In
serial mode, each channel’s equalization and pre-emphasis are
controlled only through the registers, as described in Table 8.
Additionally, further functionality is available in serial mode as
each channel’s output can be enabled/disabled with the Output
Enable control bits, which is not possible in pin mode. To
change the switching in the AD8153 to serial mode, the mask
bits (Register 0x00) must be set to 1 by writing the value 0x1F to
this register, as explained in the following sections. Once all the
mask bits are set to 1, switching is controlled via the LB_A,
LB_B, LB_C, SEL, and BICAST bits in the register set.
In mixed mode, each channel’s equalization and pre-emphasis
are controlled through the registers as described above. The
switching, however, can be controlled using either the external
Table 8. Register Map
Address
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Default
00000000
(0x00)
00000000
(0x00)
BICAST MASK
SEL MASK
LB_C MASK
LB_B MASK
LB_A MASK
00000001
(0x01)
00000000
(0x00)
OUTPUT DISABLE A
OUTPUT DISABLE B
OUTPUT DISABLE C
LB_A
LB_B
LB_C
EQ_A
EQ_B
EQ_C
PE_A [1]
PE_B [1]
PE_C [1]
BICAST
PE_A [0]
PE_B [0]
PE_C [0]
SEL
00000010
(0x02)
00000000
(0x00)
00000011
(0x03)
00000000
(0x00)
0000100
(0x04)
00000000
(0x00)
Rev. 0 | Page 15 of 24
AD8153
10. Send a repeated start condition (while holding the SCL line
high, pull the SDA line low) and continue with Step 2 in this
procedure to perform another write.
I2C DATA WRITE
To write data to the AD8153 register set, a microcontroller, or
any other I2C master, needs to send the appropriate control
signals to the AD8153 slave device. The steps that need to be
followed are listed below, where the signals are controlled by the
I2C master unless otherwise specified. A diagram of the procedure
is shown in Figure 32.
11. Send a repeated start condition (while holding the SCL line
high, pull the SDA line low) and continue with Step 2 of the
read procedure (in the I2C Data Read section) to perform a
read from another address.
12. Send a repeated start condition (while holding the SCL line
high, pull the SDA line low) and continue with step 8 of the
read procedure (in the I2C Data Read section) to perform a
read from the same address set in Step 5.
1. Send a start condition (while holding the SCL line high, pull
the SDA line low).
2. Send the AD8153 part address (seven bits) whose upper
four bits are the static value b1001 and whose lower three
bits are controlled by the input pins I2C_A[2:0]. This
transfer should be MSB first.
The AD8153 write process is shown in Figure 32. The SCL
signal is shown along with a general write operation and a
specific example. In the example, data 0x92 is written to
Address 0x6D of an AD8153 part with a part address of 0x4B.
The part address is seven bits wide and is composed of the
AD8153 static upper four bits (b1001) and the pin
programmable lower three bits (I2C_ADDR[2:0]). In this
example, the I2C_ADDR bits are set to b011. In Figure 32, the
corresponding step number is visible in the circle under the
waveform. The SCL line is driven by the I2C master and never
by the AD8153 slave. As for the SDA line, the data in the shaded
polygons is driven by the AD8153, whereas the data in the non-
shaded polygons is driven by the I2C master. The end phase case
shown is that of 9a.
3. Send the write indicator bit (0).
4. Wait for the AD8153 to acknowledge the request.
5. Send the register address (eight bits) to which data is to be
written. This transfer should be MSB first.
6. Wait for the AD8153 to acknowledge the request.
7. Send the data (eight bits) to be written to the register whose
address was set in Step 5. This transfer should be MSB first.
8. Wait for the AD8153 to acknowledge the request.
9. Send a stop condition (while holding the SCL line high, pull
the SDA line high) and release control of the bus.
It is important to note that the SDA line only changes when the
SCL line is low, except for the case of sending a start, stop, or
repeated start condition, Step 1 and Step 9 in this case.
SCL
ADDR
[2:0]
SDA
START FIXED PART ADDR
RW
REGISTER ADDR
ACK
DATA
ACK STOP
ACK
(GENERAL CASE)
SDA
(EXAMPLE)
1
2
2
3
4
5
6
7
8
9a
Figure 32. I2C Write Diagram
Rev. 0 | Page 16 of 24
AD8153
12. Acknowledge the data.
I2C DATA READ
13. Send a stop condition (while holding the SCL line high, pull
the SDA line high) and release control of the bus.
To read data from the AD8153 register set, a microcontroller, or
any other I2C master, needs to send the appropriate control
signals to the AD8153 slave device. The steps to be followed are
listed below, where the signals are controlled by the I2C master
unless otherwise specified. A diagram of the procedure can be
seen in Figure 33.
14. Send a repeated start condition (while holding the SCL line
high, pull the SDA line low) and continue with Step 2 of the
write procedure (see the I2C Data Write section) to perform
a write.
1. Send a start condition (while holding the SCL line high, pull
the SDA line low).
15. Send a repeated start condition (while holding the SCL line
high, pull the SDA line low) and continue with Step 2 of this
procedure to perform a read from another address.
2. Send the AD8153 part address (seven bits) whose upper
four bits are the static value b1001 and whose lower three
bits are controlled by the input pins I2C_ADDR[2:0]. This
transfer should be MSB first.
16. Send a repeated start condition (while holding the SCL line
high, pull the SDA line low) and continue with Step 8 of this
procedure to perform a read from the same address.
3. Send the write indicator bit (0).
The AD8153 read process is shown in Figure 33. The SCL signal
is shown along with a general read operation and a specific
example. In the example, Data 0x49 is read from Address 0x6D
of an AD8153 part with a part address of 0x4B. The part address is
seven bits wide and is composed of the AD8153 static upper
four bits (b1001) and the pin programmable lower three bits
(I2C_ADDR[2:0]). In this example, the I2C_ADDR bits are set
to b011. In Figure 33, the corresponding step number is visible
in the circle under the waveform. The SCL line is driven by the
I2C master and never by the AD8153 slave. As for the SDA line,
the data in the shaded polygons is driven by the AD8153,
whereas the data in the nonshaded polygons is driven by the I2C
master. The end phase case shown is that of 13a.
4. Wait for the AD8153 to acknowledge the request.
5. Send the register address (eight bits) from which data is to
be read. This transfer should be MSB first. The register
address is kept in memory in the AD8153 until the part is
reset or the register address is written over with the same
procedure (Step 1 to Step 6).
6. Wait for the AD8153 to acknowledge the request.
7. Send a repeated start condition (while holding the SCL line
high, pull the SDA line low).
8. Send the AD8153 part address (seven bits) whose upper
four bits are the static value b1001 and whose lower three
bits are controlled by the input pins I2C_ADDR[1:0]. This
transfer should be MSB first.
It is important to note that the SDA line only changes when the
SCL line is low, except for the case of sending a start, stop, or
repeated start condition, as in Step 1, Step 7, and Step 13. In
Figure 33, A is the same as ACK in Figure 32. Equally, Sr
represents a repeated start where the SDA line is brought high
before SCL is raised. SDA is then dropped while SCL is still high.
9. Send the read indicator bit (1).
10. Wait for the AD8153 to acknowledge the request.
11. The AD8153 then serially transfers the data (eight bits) held
in the register indicated by the address set in Step 5.
SCL
ADDR
[2:0]
ADDR
[2:0]
SDA
R
R
FIXED PART
ADDR
FIXED PART
ADDR
A
A
START
REGISTER ADDR
A
6
DATA
A
STOP
13a
Sr
W
W
(GENERAL CASE)
SDA
(EXAMPLE)
1
2
2
3
4
5
7
8
8
9
10
11
12
Figure 33. I2C Read Diagram
Rev. 0 | Page 17 of 24
AD8153
APPLICATIONS INFORMATION
The main application of the AD8153 is to support redundancy
on both the backplane side and the line interface side of a serial
link. Figure 34 illustrates redundancy in a typical backplane
system. Each line card is connected to two switch fabrics
(primary and redundant). The device can be configured to
support either 1 + 1 or 1:1 redundancy.
Another application for the AD8153 is in test equipment for
evaluating high speed serial links. Figure 36 illustrates a
possible application of the AD8153 in a simple link tester.
PRIMARY
SWITCH
FABRIC
PHYSICAL
DIGITAL ENGINE
INTERFACE
AD8153
LINE CARDS
REDUNDANT
SWITCH
FABRIC
PHYSICAL
INTERFACE
DIGITAL ENGINE
AD8153
FABRIC CARDS
BACKPLANE
Figure 34. Switch Redundancy Application
SFP
SFP
CDR
PROCESSING
ENGINE/CROSSBAR/
BACKPLANE
CDR
AD8153
Figure 35. Line Interface Redundancy Application
DUT
CONNECTOR
AD8153
PROTOCOL
ANALYZER
FPGA
Figure 36. Test Equipment Application
Rev. 0 | Page 18 of 24
AD8153
PCB DESIGN GUIDELINES
Proper RF PCB design techniques must be used for optimal
performance.
Transmission Lines
Use of 50 Ω transmission lines is required for all high frequency
input and output signals to minimize reflections. It is also
necessary for the high speed pairs of differential input traces to
be matched in length, as well as the high speed pairs of differential
output traces, to avoid skew between the differential traces.
Power Supply Connections and Ground Planes
Use of one low impedance ground plane is recommended. The
VEE pins should be soldered directly to the ground plane to
reduce series inductance. If the ground plane is an internal
plane and connections to the ground plane are made through
vias, multiple vias can be used in parallel to reduce the series
inductance. The exposed pad should be connected to the VEE
plane using plugged vias so that solder does not leak through
the vias during reflow.
Soldering Guidelines for Chip Scale Package
The lands on the 32-lead LFCSP are rectangular. The printed
circuit board pad for these should be 0.1 mm longer than the
package land length and 0.05 mm wider than the package land
width. The land should be centered on the pad. This ensures
that the solder joint size is maximized. The bottom of the chip
scale package has a central exposed pad. The pad on the printed
circuit board should be at least as large as this exposed pad. The
user must connect the exposed pad to VEE using plugged vias
so that solder does not leak through the vias during reflow. This
ensures a solid connection from the exposed pad to VEE.
Use of a 10 μF electrolytic capacitor between VCC and VEE is
recommended at the location where the 3.3 V supply enters the
PCB. It is recommended that 0.1 μF and 1 nF ceramic chip
capacitors be placed in parallel at each supply pin for high
frequency power supply decoupling. When using 0.1 μF and 1 nF
ceramic chip capacitors, they should be placed between the IC
power supply pins (VCC, VTTI, VTTO) and VEE, as close as
possible to the supply pins.
By using adjacent power supply and GND planes, excellent high
frequency decoupling can be realized by using close spacing
between the planes. This capacitance is given by
CPLANE = 0.88εr A/d (pF)
where:
εr is the dielectric constant of the PCB material.
A is the area of the overlap of power and GND planes (cm2).
d is the separation between planes (mm).
For FR4, εr = 4.4 and 0.25 mm spacing, C ~15 pF/cm2.
Rev. 0 | Page 19 of 24
AD8153
INTERFACING TO THE AD8153
TERMINATION STRUCTURES
AC Coupling
One way to simplify the input circuit and make it compatible
with a wide variety of driving devices is to use ac coupling. This
has the effect of isolating the dc common-mode levels of the
driver and the AD8153 input circuitry. AC coupling requires a
capacitor in series with each single-ended input signal, as shown
in Figure 39. This should be done in a manner that does not
interfere with the high speed signal integrity of the PCB.
To determine the best strategy for connecting to the high speed
pins of the AD8153, the user must first be familiar with the on-
chip termination structures. The AD8153 contains two types of
these structures: one type for input ports and one type for output
ports (see Figure 37 and Figure 38).
VCC
V
V
V
CC
TTI
CC
VTTI
55Ω
55Ω
50Ω
50Ω
55Ω
55Ω
C
P
IP
IN
IPX
INX
C
N
1173Ω
1173Ω
VEE
AD8153
VEE
DRIVER
Figure 37. Receiver Simplified Diagram
Figure 39. AC-Coupling Input Signal of AD8153
When ac coupling is used, the common-mode level at the input
of the device is equal to VTTI. The single-ended input signal
swings above and below VTTI equally. The user can then use
the specifications in Table 1 to determine the input signal swing
levels that satisfy the input range of the AD8153.
VCC
VTTO
50Ω
50Ω
OPX
ONX
If dc coupling is required, determining the input common-
mode level is less straightforward because the configuration of
the driver must also be considered. In most cases, the user
would set VTTI on the AD8153 to the same level as the driver
output termination voltage. This prevents a continuous dc
current from flowing between the two supply nets. As a
practical matter, both devices can be terminated to the same
physical supply net.
V
V
IP
IN
I
T
VEE
Figure 38. Transmitter Simplified Diagram
Consider the following example: a driver is dc-coupled to the
input of the AD8153. The AD8153 input termination voltage
(VTTI) and the driver output termination voltage (VTTOD) are both
set to the same level; that is, VTTI = VTTOD = 3.3 V. If an 800 mV
differential p-p swing is desired, the total output current of the
driver is 16 mA. At balance, the output current is divided evenly
between the two sides of the differential signal path, 8 mA to each
side. This 8 mA of current flows through the parallel combina-
tion of the 55 Ω input termination resistor on the AD8153 and
the 50 Ω output termination resistor on the driver, resulting in a
common-mode level of
For input ports, the termination structure consists of two 55 Ω
resistors connected to a termination supply and an 1173 Ω
resistor connected across the differential inputs, the latter being
a result of the finite differential input impedance of the equalizer.
For output ports, there are two 50 Ω resistors connected to the
termination supply. Note that the differential input resistance
for both structures is the same, 100 Ω.
INPUT COMPLIANCE
The range of allowable input voltages is determined by the
fundamental limitations of the active input circuitry. This range
of signals is normally a function of the common-mode level of
the input signal, the signal swing, and the supply voltage. For a
given input signal swing, there is a range of common-mode
voltages that keeps the high and low voltage excursions within
acceptable limits. Similarly, for a given common-mode input
voltage, there is a maximum acceptable input signal swing.
There is also a minimum signal swing that the active input
circuitry can resolve reliably. The specifications are found in
Table 1.
V
TTI − 8 mA × (50 Ω || 55 Ω) = VTTI − 209 mV
The user can then determine the allowable range of values for VTTI
that meets the input compliance range based on an 800 mV p-p
differential swing.
Rev. 0 | Page 20 of 24
AD8153
Table 9 shows an example calculation of the output levels for the
typical case, where VCC = VTTO = 3.3 V, with 50 Ω far-end
terminations to a 3.3 V supply.
OUTPUT COMPLIANCE
Figure 40 is a graphical depiction of the single-ended waveform
at the output of the AD8153. The common-mode level (VOCM
)
and the amplitude (VOSE) of this waveform are a function of the
output tail current (IT), the output termination supply voltage
(VTTO), the topology of the far-end receiver, and whether ac- or
dc-coupling is used. Keep in mind that the output tail current
varies with the pre-emphasis level. The user must ensure that
the high (VH) and low (VL) voltage excursions at the output are
within the single-ended absolute voltage range limits as
V
TTO
V
H
V
OCM
V
OSE-DC
V
OSE-BOOST
V
L
~320ps
specified in Table 1. Failure to understand the implications of
output signal levels and the choice of ac- or dc-coupling may
lead to transistor saturation and poor transmitter performance.
Figure 40. Single-Ended Output Waveform
Table 9. Output Voltage Levels
DC-Coupled
AC-Coupled
PE Setting
IT (mA)
16
20
24
28
VOSE-DC (mV p-p)
VOSE-BOOST (mV p-p)
VOCM (V)
3.1
3.05
3
VH (V)
3.3
3.3
3.3
3.3
VL (V)
2.9
2.8
2.7
2.6
VOCM (V)
2.9
2.8
2.7
2.6
VH (V)
3.1
3.05
3
VL (V)
2.7
2.55
2.4
0
1
2
3
400
400
400
400
400
500
600
700
2.95
2.95
2.25
Table 10. Symbol Definitions
Symbol
Formula
Definition
VOSE-DC
Single-ended output voltage swing after settling
IT PE=0 × 25Ω
VOSE-BOOST
Boosted single-ended output voltage swing
IT ×25Ω
VOCM (dc-coupled)
Common-mode voltage when the output is dc-coupled
IT
VTTO
VTTO
−
−
×25Ω
×50Ω
2
IT
2
VOCM (ac-coupled)
Common-mode voltage when the output is ac-coupled
VH
VL
High single-ended output voltage excursion
Low single-ended output voltage excursion
VOCM + VOSE-BOOST/2
VOCM - VOSE-BOOST/2
Rev. 0 | Page 21 of 24
AD8153
OUTLINE DIMENSIONS
5.00
BSC SQ
0.60 MAX
0.60 MAX
PIN 1
INDICATOR
25
32
1
24
0.50
BSC
PIN 1
INDICATOR
TOP
VIEW
2.85
2.70 SQ
2.55
*
4.75
BSC SQ
EXPOSED
PAD
(BOT TOM VIEW)
0.50
0.40
0.30
17
16
8
9
0.20 MIN
3.50 REF
0.80 MAX
1.00
0.85
0.80
12° MAX
0.65 TYP
0.05 MAX
0.02 NOM
0.30
0.25
0.18
SEATING
PLANE
COPLANARITY
0.08
0.20 REF
COMPLIANT TO JEDEC STANDARDS MO-220-VHHD-2
*
THE AD8153 HAS A CONDUCTIVE HEAT SLUG TO HELP DISSIPATE HEAT AND ENSURE RELIABLE OPERATION OF
THE DEVICE OVER THE FULL INDUSTRIAL TEMPERATURE RANGE. THE SLUG IS EXPOSED ON THE BOTTOM OF
THE PACKAGE AND ELECTRICALLY CONNECTED TO V . IT IS RECOMMENDED THAT NO PCB SIGNAL
EE
TRACES OR VIAS BE LOCATED UNDER THE PACKAGE THAT COULD COME IN CONTACT WITH THE CONDUCTIVE
SLUG.
Figure 41. 32-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
5 mm × 5 mm Body, Very Thin Quad
(CP-32-8)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD8153ACPZ1
Temperature Range
Package Description
Package Option
CP-32-8
CP-32-8
−40°C to +85°C
32-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
Evaluation Board
AD8153ACPZ-RL71 −40°C to +85°C
AD8153-EVALZ1
1 Z = RoHS Compliant Part.
Rev. 0 | Page 22 of 24
AD8153
NOTES
Rev. 0 | Page 23 of 24
AD8153
NOTES
©2007 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06393-0-4/07(0)
Rev. 0 | Page 24 of 24
相关型号：
©2020 ICPDF网 联系我们和版权申明