AD8619_15_技术文档

Low Cost Micropower, Low Noise CMOS

Rail-to-Rail, Input/Output Operational Amplifiers

Data Sheet

AD8613/AD8617/AD8619

FEATURES

PIN CONFIGURATIONS

Offset voltage: 2.2 mV maximum

Low input bias current: 1 pA maximum

Single-supply operation: 1.8 V to 5.5 V

Low noise: 22 nV/√Hz

1

2

3

5

OUT

V–

V+

AD8613

TOP VIEW

(Not to Scale)

4

+IN

–IN

Micropower: 50 μA/amplifier maximum over temperature

No phase reversal

Unity gain stable

Figure 1. 5-Lead SC70 and 5-Lead TSOT-23

OUT A

–IN A

+IN A

V–

1

2

3

4

8

7

6

5

V+

AD8617

TOP VIEW

(Not to Scale)

OUT B

–IN B

+IN B

Qualified for automotive applications

APPLICATIONS

Battery-powered instrumentation

Multipole filters

Figure 2. 8-Lead MSOP and 8-Lead SOIC_N

Current shunt sense

Sensors

ADC predrivers

DAC drivers/level shifters

Low power ASIC input or output amplifiers

OUT A 1

–IN A 2

+IN A 3

V– 4

8 V+

AD8617

TOP VIEW

(Not to Scale)

7 OUT B

6 –IN B

5 +IN B

NOTES

1. PIN 4 AND THE EXPOSED PAD

MUST BE CONNECTED TO V–.

GENERAL DESCRIPTION

The AD8613/AD8617/AD8619 are single, dual, and quad micro-

power, rail-to-rail input and output amplifiers that feature low

supply current, as well as low input voltage and current noise.

Figure 3. 8-Lead LFCSP_VD

1

OUT A

–IN A

+IN A

V+

14

13

12

11

OUT D

–IN D

+IN D

V–

2

3

4

5

6

7

The parts are fully specified to operate from 1.8 V to 5 V single

supply, or ±±.9 V and ±ꢀ.5 V dual supply. The combination of low

noise, very low input bias currents, and low power consumption

make the AD8613/AD8617/AD8619 especially useful in portable

and loop-powered instrumentation.

AD8619

TOP VIEW

(Not to Scale)

+IN B

–IN B

OUT B

10 +IN C

9

8

–IN C

OUT C

The ability to swing rail-to-rail at both the input and output

enables designers to buffer CMOS ADCs, DACs, ASICs, and

other wide output swing devices in low power, single-supply

systems.

Figure 4. 14-Lead TSSOP and 14-Lead SOIC

The AD8613 is available in a 5-lead SC7± package and a 5-lead

TSOT-ꢀ3 package. The AD8617 is available in 8-lead MSOP,

8-lead SOIC, and 8-lead LFCSP packages. The AD8619 is available

in 14-lead TSSOP and 14-lead SOIC packages. The AD8617W is

qualified for automotive applications and is available in an

8-lead MSOP package and an 8-lead SOIC package. The

AD8619W is qualified for automotive applications and is

available in a 14-lead TSSOP.

Rev. F

Document Feedback

Information furnished by Analog Devices is believed to be accurate and reliable. However, no

responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other

rights of third parties that may result from its use. Specifications subject to change without notice. No

license is granted by implication or otherwise under any patent or patent rights of Analog Devices.

Trademarks and registeredtrademarks arethe property of their respective owners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.

Technical Support

www.analog.com

AD8613/AD8617/AD8619

Data Sheet

TABLE OF CONTENTS

Features .............................................................................................. 1

Thermal Resistance.......................................................................5

ESD Caution...................................................................................5

Typical Performance Characteristics ..............................................6

Outline Dimensions....................................................................... 12

Ordering Guide .......................................................................... 15

Automotive Products................................................................. 15

Applications....................................................................................... 1

General Description......................................................................... 1

Pin Configurations ........................................................................... 1

Revision History ............................................................................... 2

Specifications..................................................................................... 3

Absolute Maximum Ratings............................................................ 5

REVISION HISTORY

4/14—Rev. E to Rev. F

1/06—Rev. A to Rev. B

Changes to General Description Section ...................................... 1

Changes to Table 3............................................................................ 5

Changes to Ordering Guide .......................................................... 15

Added Automotive Products Section .......................................... 15

Added AD8613....................................................................Universal

Changes to Features ..........................................................................1

Changes to Table 1.............................................................................3

Changes to Table 2.............................................................................4

Updated Outline Dimensions....................................................... 12

Changes to Ordering Guide.......................................................... 13

3/10—Rev. D to Rev. E

Changes to General Description .................................................... 1

Changes to Ordering Guide .......................................................... 15

10/05—Rev. 0 to Rev. A

Added AD8619....................................................................Universal

Change to Specifications Section ....................................................3

Updated Outline Dimensions....................................................... 12

Changes to Ordering Guide.......................................................... 13

3/10—Rev. C to Rev. D

Changes to General Description .................................................... 1

Changes to Ordering Guide .......................................................... 15

10/09—Rev. B to Rev. C

9/05—Revision 0: Initial Version

Added 8-Lead LFCSP Package..........................................Universal

Changes to Features Section, Figure 2 Caption, General

Description Section, and Figure 3.................................................. 1

Changed V_Sto V_SYThroughout...................................................... 3

Changes to Input Characteristics, Input Voltage Range

Parameter; Dynamic Performance, Settling Time to 0.1% and

Phase Margin Parameters; and Noise Performance, Peak-to-

Peak Noise Parameter, Table 1 ........................................................ 3

Changes to Input Characteristics, Input Voltage Range

Parameter; Dynamic Performance, Settling Time to 0.1% and

Phase Margin Parameters; and Noise Performance, Peak-to-

Peak Noise Parameter, Table 2 ........................................................ 4

Changes to Table 3 and Table 4....................................................... 5

Changes to Figure 12 to Figure 15.................................................. 7

Changes to Figure 18 Caption ........................................................ 8

Changes to Figure 30 and Figure 31............................................. 10

Updated Outline Dimensions ....................................................... 12

Added Figure 44; Renumbered Sequentially .............................. 14

Changes to Ordering Guide .......................................................... 15

Rev. F | Page 2 of 16

Data Sheet

AD8613/AD8617/AD8619

SPECIFICATIONS

Electrical characteristics at V_SY= 5 V, V _CM= V_SY/2, T_A= 25°C, unless otherwise noted.

Table 1.

Parameter

Symbol

V_OS

Conditions

Min

Typ

Max

Unit

INPUT CHARACTERISTICS

Offset Voltage

−0.3 V < V_CM< +5.3 V

−40°C < T_A< +125°C, −0.3 V < V_CM< +5.2 V

−40°C < T_A< +125°C

0.4

2.2

4.5

7.0

1

mV

µV/°C

pA

Offset Voltage Drift

AD8613

Input Bias Current

∆V_OS/∆T

I_B

1

2.5

0.2

−40°C < T_A< +85°C

−40°C < T_A< +125°C

110

780

0.5

50

250

5

pA

V

Input Offset Current

I_OS

0.1

−40°C < T_A< +85°C

−40°C < T_A< +125°C

Input Voltage Range

IVR

0

Common-Mode Rejection Ratio

CMRR

0 V < V_CM< 5 V

95

dB

−40°C < T_A< +125°C

R_L= 10 kΩ, 0.5 V < V_O< 4.5 V

68

235

dB

V/mV

pF

Large Signal Voltage Gain

Input Capacitance

A_VO

C_DIFF

C_CM

500

1.9

2.5

pF

OUTPUT CHARACTERISTICS

Output Voltage High

V_OH

I_L= 1 mA

−40°C to +125°C

I_L= 10 mA

4.95

4.9

4.98

4.7

V

−40°C to +125°C

I_L= 1 mA

−40°C to +125°C

I_L= 10 mA

4.50

V

Output Voltage Low

V_OL

20

30

50

275

335

mV

mA

Ω

190

−40°C to +125°C

Short-Circuit Current

Closed-Loop Output Impedance

POWER SUPPLY

I_SC

Z_OUT

80

15

f = 10 kHz, A_V= 1

Power Supply Rejection Ratio

PSRR

I_SY

1.8 V < V_SY< 5 V

−40°C < T_A< +125°C

V_O= V_SY/2

67

64

94

38

dB

µA

Supply Current/Amplifier

−40°C <T_A< +125°C

50

DYNAMIC PERFORMANCE

Slew Rate

Settling Time to 0.1%

Gain Bandwidth Product

SR

t_S

GBP

R_L= 10 kΩ

0.1

23

400

350

70

V/µs

μs

kHz

Degrees

G = 1, V_IN= 2 V step, C_L= 20 pF, R_L= 1 kΩ

R_L= 100 kΩ

R_L= 10 kΩ

Phase Margin

Ø_M

R_L= 10 kΩ, R_L= 100 kΩ, C_L= 20 pF

NOISE PERFORMANCE

Peak-to-Peak Noise

Voltage Noise Density

e_np-p

e_n

0.1 Hz to 10 Hz

f = 1 kHz

f = 10 kHz

f = 1 kHz

2.3

25

22

3.5

µV

nV/√Hz

pA/√Hz

Current Noise Density

i_n

0.05

Rev. F | Page 3 of 16

AD8613/AD8617/AD8619

Data Sheet

Electrical characteristics at V_SY= 1.8 V, V_CM= V_SY/2, T_A= 25°C, unless otherwise noted.

Table 2.

Parameter

Symbol

V_OS

Conditions

Min

Typ

Max

Unit

INPUT CHARACTERISTICS

Offset Voltage

−0.3 V < V_CM< +1.9 V

−0.3 V < V_CM< +1.8 V; −40°C < T_A< +125°C

−40°C < T_A< +125°C

0.4

2.2

8.5

9.0

1

mV

µV/°C

pA

Offset Voltage Drift

AD8613

Input Bias Current

∆V_OS/∆T

I_B

1

3.7

0.2

−40°C < T_A< +85°C

−40°C < T_A< +125°C

110

780

0.5

50

250

1.8

pA

V

Input Offset Current

I_OS

0.1

−40°C < T_A< +85°C

−40°C < T_A< +125°C

Input Voltage Range

IVR

0

Common-Mode Rejection Ratio

CMRR

0 V < V_CM< 1.8 V

−40°C < T_A< +125°C

R_L= 10 kΩ, 0.5 V < V_O< 1.3 V

58

55

85

86

dB

V/mV

pF

Large Signal Voltage Gain

Input Capacitance

A_VO

C_DIFF

C_CM

1000

2.1

3.8

OUTPUT CHARACTERISTICS

Output Voltage High

V_OH

V_OL

I_L= 1 mA

−40°C to +125°C

1.65

1.6

1.73

44

V

Output Voltage Low

I_L= 1 mA

−40°C to +125°C

60

80

mV

mA

Ω

Short-Circuit Current

Closed-Loop Output Impedance

POWER SUPPLY

I_SC

Z_OUT

7

15

f = 10 kHz, A_V= 1

Power Supply Rejection Ratio

Supply Current/Amplifier

PSRR

I_SY

1.8 V < V_S< 5 V

V_O= V_SY/2

−40°C <T_A< +125°C

67

94

38

dB

µA

50

DYNAMIC PERFORMANCE

Slew Rate

Settling Time to 0.1%

Gain Bandwidth Product

SR

t_S

GBP

R_L= 10 kΩ

0.1

6.5

400

350

70

V/µs

µs

kHz

Degrees

G = 1, V_IN= 1 V step, C_L= 20 pF, R_L= 1 kΩ

R_L= 100 kΩ

R_L= 10 kΩ

Phase Margin

Ø_M

R_L= 10 kΩ, R_L= 100 kΩ, C_L= 20 pF

NOISE PERFORMANCE

Peak-to-Peak Noise

Voltage Noise Density

e_np-p

e_n

0.1 Hz to 10 Hz

f = 1 kHz

f = 10 kHz

f = 1 kHz

2.3

25

22

3.5

µV

nV/√Hz

pA/√Hz

Current Noise Density

i_n

0.05

Rev. F | Page 4 of 16

Data Sheet

AD8613/AD8617/AD8619

ABSOLUTE MAXIMUM RATINGS

THERMAL RESISTANCE

T_A= 25°C, unless otherwise noted.

θ_JAis specified for the worst-case conditions, that is, a device

soldered in a circuit board for surface-mount packages.

Table 3.

Parameter

Rating

Table 4. Thermal Characteristics

Package Type

Supply Voltage

Input Voltage

6 V

V_SS− 0.3 V to V_DD+ 0.3 V

θ_JA

θ_JC

61

126

45

43

20

36

35

Unit

°C/W

Input Current

Differential Input Voltage

10 ꢀm

6 V

5-Lead TSOT-23 (UJ-5)

5-Lead SC70 (KS-5)

207

376

210

158

81

Output Short-Circuit Duration to GND Indefinite

8-Lead MSOP (RM-8)

8-Lead SOIC_N (R-8)

8-Lead LFCSP_VD (CP-8-9)

14-Lead SOIC_N (R-14)

14-Lead TSSOP (RU-14)

Storage Teꢀperature Range

−65°C to +150°C

Operating Teꢀperature Range

Junction Teꢀperature Range

Lead Teꢀperature (Soldering, 60 sec)

−40°C to +125°C

−65°C to +150°C

300°C

120

180

ESD mD8613

HBM

FICDM

ESD mD8617

HBM

4000 V

1000 V

ESD CAUTION

3000 V

1000 V

100 V

FICDM

MM

ESD mD8619

HBM

4000 V

1250 V

200 V

FICDM

MM

Stresses above those listed under Absolute Maximum Ratings

may cause permanent damage to the device. This is a stress

rating only; functional operation of the device at these or any

other conditions above those indicated in the operational

section of this specification is not implied. Exposure to absolute

maximum rating conditions for extended periods may affect

device reliability.

Rev. F | Page 5 of 16

AD8613/AD8617/AD8619

Data Sheet

TYPICAL PERFORMANCE CHARACTERISTICS

V_SY= 5 V or 2.5 V, unless otherwise noted.

1800

400

350

300

250

200

150

100

50

V

= 5.5V

SY

–0.5V < V

V

= 5V AND 1.8V

SY

< +5.5V

CM

= 25°C

1600

1400

1200

1000

800

600

400

200

0

T

A

0

25

50

75

100

125

150

TEMPERATURE (°C)

INPUT OFFSET VOLTAGE (µV)

Figure 8. Input Bias Current vs. Temperature

Figure 5. Input Offset Voltage Distribution

50

40

30

20

10

0

40

35

30

25

20

15

10

5

–40°C < T < 125°C

A

T

= 25°C

A

V

= 2.5V

CM

0

1

2

3

5

0

1

2

3

4

5

6

7

8

9

10

SUPPLY VOLTAGE (V)

TCV (µV/°C)

OS

Figure 6. Input Offset Voltage Drift Distribution

Figure 9. Supply Current vs. Supply Voltage

2000

1500

1000

500

50

40

30

20

10

0

V

= 5V

SY

= 25°C

V

= ±2.5V, ±1.35V, ±0.9V

SY

T

A

0

–500

–1000

–1500

–2000

–0.5

0

0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5

INPUT COMMON MODE VOLTAGE (V)

–40

–10

20

50

80

110

TEMPERATURE (°C)

Figure 10. Supply Current vs. Temperature

Figure 7. Input Offset Voltage vs. Input Common-Mode Voltage

Rev. F | Page 6 of 16

Data Sheet

AD8613/AD8617/AD8619

135

1k

60

50

V

A

= 5V

SY

= 25ºC

T

100

10

V

– V

OH

SY

90

40

SOURCE

30

45

20

ΦM

1

10

SINK

0

V

OL

0.1

0.01

V

R

C

= ±2.5V AND ±0.9V

= 100kΩ

= 20pF

SY

–10

–20

L

–45

1M

0.001

0.01

0.1

LOAD CURRENT (mA)

1

10

1k

10k

100k

FREQUENCY (Hz)

Figure 11. Output Voltage to Supply Rail vs. Load Current

Figure 14. Open-Loop Gain and Phase vs. Frequency

40

120

100

80

60

40

20

0

V

= 5V

V

= 5V AND 2.7V

SY

= 25°C

T

A

30

20

10

0

V

– V @ 1mA

OH

SY

V

@ 1mA

OL

–40 –25 –10

5

20

35

50

65

80

95 110 125

100

1k

10k

100k

1M

FREQUENCY (Hz)

TEMPERATURE (°C)

Figure 12. Output Voltage to Supply Rail vs. Temperature

(I_L= 1 mA)

Figure 15. CMRR vs. Frequency

350

300

250

200

150

100

50

120

100

80

60

40

20

0

V

= 5V

SY

V

= ±2.5V AND ±1.35V

SY

= 25°C

T

A

V

– V @ 10mA

OH

SY

V

@ 10mA

OL

0

–40 –25 –10

5

20

35

50

65

80

95 110 125

100

1k

10k

100k

1M

TEMPERATURE (°C)

FREQUENCY (Hz)

Figure 13. Output Voltage to Supply Rail vs. Temperature

(I_L= 10 mA)

Figure 16. PSRR vs. Frequency

Rev. F | Page 7 of 16

AD8613/AD8617/AD8619

Data Sheet

1k

V

= 5V

SY

A

R

C

= 1

= 10kΩ

= 200pF

V

L

A

= 100

V

100

10

1

A

= 10

V

A

= 1

V

= 5V AND 1.8V

SY

0

100

1k

10k

FREQUENCY (Hz)

100k

1M

TIME (20µs/DIV)

Figure 17. Output Impedance vs. Frequency

Figure 20. Large Signal Transient Response

50

45

40

35

30

25

20

15

10

5

V

= 5V

= 25°C

SY

0

T

A

V

A

= ±2.5V

= –50

SY

V

–2.5

100

0

–OS

+OS

0

10

100

LOAD CAPACITANCE (pF)

1000

TIME (20µs/DIV)

Figure 18. Small Signal Overshoot vs. Load Capacitance

Figure 21. Positive Overload Recovery

V

= 5V, 2.7V, 1.8V

= 1

= 10kΩ

= 200pF

SY

V

A

= ±2.5V

= –50

SY

A

R

C

V

L

2.5

V

0

–100

TIME (4µs/DIV)

TIME (20µs/DIV)

Figure 19. Small Signal Transient Response

Figure 22. Negative Overload Recovery

Rev. F | Page 8 of 16

Data Sheet

AD8613/AD8617/AD8619

1000

100

10

V

= 5V

= 25ºC

SY

V

IN

T

A

V

OUT

1/F CORNER @ 100Hz

V

= ±2.5V

SY

A

R

= 1

= 10kΩ

V

L

V

= 6V p-p

IN

1

10

100

1000

10000

TIME (20ms/DIV)

FREQUENCY (Hz)

Figure 23. No Phase Reversal

Figure 25. Voltage Noise Density

140

120

100

80

V

= 5V AND 2.7V

V

= 5V

SY

60

40

20

0

100

1k

10k

100k

1M

TIME (1s/DIV)

FREQUENCY (Hz)

Figure 24. 0.1 Hz to 10 Hz Input Voltage Noise

Figure 26. Channel Separation

Rev. F | Page 9 of 16

AD8613/AD8617/AD8619

Data Sheet

V_SY= 1.8 V or 0.9 V, unless otherwise noted.

450

80

60

40

20

0

V

= 1.8V

V

= 1.8V

SY

0V < V

< 1.8V

CM

= 25°C

400

350

300

250

200

150

100

50

T

A

V

–V @ 1mA

SY OH

V

@ 1mA

OH

80

0

–40 –25 –10

5

20

35

50

65

95 110 125

TEMPERATURE (°C)

INPUT OFFSET VOLTAGE (µV)

Figure 27. Input Offset Voltage Distribution

Figure 30. Output Voltage to Supply Rail vs. Temperature

(I_L= 1 mA)

2000

1500

1000

500

100

80

60

40

20

0

V

T

= 1.8V

V

T

= 1.8V

= 25°C

SY

= 25°C

SY

A

0

–500

–1000

–1500

–2000

–0.5 –0.2

0.1

0.4

0.7

1.0

1.3

1.6

1.9

2.2

100

1k

10k

100k

1M

INPUT COMMON-MODE VOLTAGE (V)

FREQUENCY (Hz)

Figure 28. Input Offset Voltage vs. Input Common-Mode Voltage

Figure 31. CMRR vs. Frequency

1000

120

100

80

60

40

20

0

V

= 1.8V

SY

= 25°C

V

= 1.8V

SY

= 25°C

T

A

T

A

100

10

V

–V

SY OH

SOURCE

1

SINK

V

OL

0.1

0.01

0.001

0.01

0.1

LOAD CURRENT (mA)

1

10

100

1k

1M

10k

FREQUENCY (Hz)

Figure 29. Output Voltage to Supply Rail vs. Load Current

Figure 32. PSRR vs. Frequency

Rev. F | Page 10 of 16

Data Sheet

AD8613/AD8617/AD8619

40

V

= 1.8V

SY

= 25°C

V

= 1.8V

SY

T

A

30

20

10

0

–OS

+OS

10

100

LOAD CAPACITANCE (pF)

1k

TIME (1s/DIV)

Figure 33. Small Signal Overshoot vs. Load Capacitance

Figure 35. 0.1 Hz to 10 Hz Input Voltage Noise

1k

100

10

V

= 1.8V

= 25°C

SY

V

= 1.8V

= 1

= 10kΩ

= 200pF

SY

T

A

R

C

V

L

1/F CORNER @ 100Hz

1

10

100

1k

10k

TIME (20µs/DIV)

FREQUENCY (Hz)

Figure 36. Voltage Noise Density

Figure 34. Large Signal Transient Response

Rev. F | Page 11 of 16

AD8613/AD8617/AD8619

OUTLINE DIMENSIONS

Data Sheet

3.20

3.00

2.80

8

1

5

4

5.15

4.90

4.65

3.20

3.00

2.80

PIN 1

IDENTIFIER

0.65 BSC

0.95

0.85

0.75

15° MAX

1.10 MAX

0.80

0.55

0.40

0.15

0.05

0.23

0.09

6°

0°

0.40

0.25

COPLANARITY

0.10

COMPLIANT TO JEDEC STANDARDS MO-187-AA

Figure 37. 8-Lead Mini Small Outline Package [MSOP]

(RM-8)

Dimensions shown in millimeters

5.00 (0.1968)

4.80 (0.1890)

8

1

5

4

6.20 (0.2441)

5.80 (0.2284)

4.00 (0.1574)

3.80 (0.1497)

0.50 (0.0196)

0.25 (0.0099)

1.27 (0.0500)

BSC

45°

1.75 (0.0688)

1.35 (0.0532)

0.25 (0.0098)

0.10 (0.0040)

8°

0°

0.51 (0.0201)

0.31 (0.0122)

COPLANARITY

0.10

1.27 (0.0500)

0.40 (0.0157)

0.25 (0.0098)

0.17 (0.0067)

SEATING

PLANE

COMPLIANT TO JEDEC STANDARDS MS-012-AA

CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS

(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR

REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.

Figure 38. 8-Lead Standard Small Outline Package [SOIC_N]

Narrow Body (R-8)

Dimensions shown in millimeters and (inches)

Rev. F | Page 12 of 16

Data Sheet

AD8613/AD8617/AD8619

8.75 (0.3445)

8.55 (0.3366)

8

7

14

1

6.20 (0.2441)

5.80 (0.2283)

4.00 (0.1575)

3.80 (0.1496)

1.27 (0.0500)

BSC

0.50 (0.0197)

0.25 (0.0098)

45°

1.75 (0.0689)

1.35 (0.0531)

0.25 (0.0098)

0.10 (0.0039)

8°

0°

COPLANARITY

0.10

SEATING

PLANE

1.27 (0.0500)

0.40 (0.0157)

0.51 (0.0201)

0.31 (0.0122)

0.25 (0.0098)

0.17 (0.0067)

COMPLIANT TO JEDEC STANDARDS MS-012-AB

CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS

(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR

REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.

Figure 39. 14-Lead Standard Small Outline Package [SOIC_N]

Narrow Body (R-14)

Dimensions shown in millimeters and (inches)

5.10

5.00

4.90

14

8

7

4.50

4.40

4.30

6.40

BSC

1

PIN 1

0.65 BSC

1.05

1.00

0.80

1.20

MAX

0.20

0.09

0.75

0.60

0.45

8°

0°

0.15

0.05

COPLANARITY

0.10

SEATING

PLANE

0.30

0.19

COMPLIANT TO JEDEC STANDARDS MO-153-AB-1

Figure 40. 14-Lead Thin Shrink Small Outline Package [TSSOP]

(RU-14)

Dimensions shown in millimeters

Rev. F | Page 13 of 16

AD8613/AD8617/AD8619

Data Sheet

2.20

2.00

1.80

2.40

2.10

1.80

5

1

4

3

1.35

1.25

1.15

2

0.65 BSC

1.10

1.00

0.90

0.70

0.40

0.10

0.80

0.46

0.36

0.26

0.22

0.08

SEATING

PLANE

0.10 MAX

0.30

0.15

COPLANARITY

0.10

COMPLIANT TO JEDEC STANDARDS MO-203-AA

Figure 41. 5-Lead Thin Shrink Small Outline Transistor Package [SC70]

(KS-5)

Dimensions shown in millimeters

2.90 BSC

5

1

4

3

2.80 BSC

1.60 BSC

2

0.95 BSC

1.90

BSC

*

0.90 MAX

0.70 MIN

*

1.00 MAX

0.20

0.08

8°

4°

0°

0.10 MAX

0.50

0.30

0.60

0.45

0.30

SEATING

PLANE

*

COMPLIANT TO JEDEC STANDARDS MO-193-AB WITH

THE EXCEPTION OF PACKAGE HEIGHT AND THICKNESS.

Figure 42. 5-Lead Thin Small Outline Transistor Package [TSOT-23]

(UJ-5)

Dimensions shown in millimeters

Rev. F | Page 14 of 16

Data Sheet

AD8613/AD8617/AD8619

3.25

3.00 SQ

2.75

0.60 MAX

5

0.50

BSC

0.60 MAX

8

2.95

2.75 SQ

2.55

EXPOSED

PAD

1.60

1.50

1.40

PIN 1

INDICATOR

4

1

PIN 1

INDICATOR

0.50

0.40

0.30

TOP VIEW

BOTTOM VIEW

2.23

2.13

2.03

12° MAX

0.70 MAX

0.65 TYP

0.90 MAX

0.85 NOM

0.05 MAX

0.01 NOM

FOR PROPER CONNECTION OF

THE EXPOSED PAD, REFER TO

THE PIN CONFIGURATION AND

FUNCTION DESCRIPTIONS

0.30

0.23

0.18

SEATING

PLANE

SECTION OF THIS DATA SHEET.

0.20 REF

Figure 43. 8-Lead Lead Frame Chip Scale Package [LFCSP_VD]

3 mm × 3 mm Body, Very Thin, Dual Lead

(CP-8-9)

Dimensions shown in millimeters

ORDERING GUIDE

Model^{1, 2}

Temperature Range

−40°C to +125°C

Package Description

5-Lead SC70

Package Option

KS-5

UJ-5

Branding

A0Y

AD8613AKSZ-R2

AD8613AKSZ-REEL

AD8613AKSZ-REEL7

AD8613AUJZ-R2

AD8613AUJZ-REEL

AD8613AUJZ-REEL7

AD8617ACPZ-R2

AD8617ACPZ-R7

AD8617ACPZ-RL

AD8617ARMZ

−40°C to +125°C

5-Lead SC70

5-Lead TSOT-23

8-Lead LFCSP_VD

8-Lead MSOP

UJ-5

A0Y

CP-8-9

RM-8

R-8

RM-8

R-8

A0T

AD8617ARMZ-REEL

AD8617ARZ

8-Lead MSOP

A0T

8-Lead SOIC_N

8-Lead MSOP

8-Lead SOIC_N

14-Lead TSSOP

14-Lead SOIC_N

14-Lead TSSOP

AD8617ARZ-REEL

AD8617ARZ-REEL7

AD8617WARMZ-REEL

AD8617WARZ-R7

AD8619ARUZ

AD8619ARUZ-REEL

AD8619ARZ

AD8619ARZ-REEL7

AD8619WARUZ-R7

AD8619WARUZ-RL

A23

RU-14

R-14

RU-14

¹Z = RoHS Compliant Part.

²Qualified for automotive applications.

AUTOMOTIVE PRODUCTS

The AD8617W and AD8619W models are available with controlled manufacturing to support the quality and reliability requirements of

automotive applications. Note that these automotive models may have specifications that differ from the commercial models; therefore,

designers should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for

use in automotive applications. Contact your local Analog Devices account representative for specific product ordering information and

to obtain the specific Automotive Reliability reports for these models.

Rev. F | Page 15 of 16

AD8613/AD8617/AD8619

NOTES

Data Sheet

registered trademarks are the property of their respective owners.

D05622-0-4/14(F)

Rev. F | Page 16 of 16


型号：	AD8619_15
厂家：	ADI
描述：	Low Cost Micropower, Low Noise CMOS
文件：	总16页 (文件大小：396K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

AD8619_15 [ADI]

相关型号：

AD8620

AD8620A

AD8620AR

AD8620AR-REEL

AD8620AR-REEL7

AD8620ARZ

AD8620ARZ-REEL

AD8620ARZ-REEL7

AD8620B

AD8620BR

AD8620BR-REEL

AD8620BR-REEL7