AD9048KN [ADI]
IC 8-BIT FLASH METHOD ADC, PARALLEL ACCESS, PDIP28, PLASTIC, DIP-28, Analog to Digital Converter;
| 型号： | AD9048KN |
| 厂家： | 
ADI |
| 描述： | IC 8-BIT FLASH METHOD ADC, PARALLEL ACCESS, PDIP28, PLASTIC, DIP-28, Analog to Digital Converter 光电二极管 转换器 |
| 文件： | 总15页 (文件大小：109K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
APPROVED
A
B
C
D
E
Changes in accordance with NOR 5962-R261-92.
92-07-13
95-07-17
98-03-27
99-02-26
99-09-16
M. A. Frye
Redrawn with changes. Add device type 03. Editorial changes throughout.
Changes to table I. Editorial changes throughout. - drw
Changes to table I, sheet 5. - drw
M. A. Frye
Raymond Monnin
Raymond Monnin
Raymond Monnin
Change test conditions of supply current tests in table I for device types 01 and
02, sheet 5. - drw
F
Change in table I, sheet 5, for device types 01 and 02. - drw
00-01-03
04-12-20
Raymond Monnin
Raymond Monnin
G
Update drawing to current requirements. Editorial changes throughout. - drw
THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
REV
G
1
G
2
G
3
G
4
G
5
G
6
G
7
G
8
G
9
G
G
G
G
G
SHEET
10
11
12
13
14
PREPARED BY
Dan Wonnell
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
http://www.dscc.dla.mil
CHECKED BY
Charles E. Besore
STANDARD
MICROCIRCUIT
DRAWING
APPROVED BY
Michael A. Frye
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
MICROCIRCUIT, LINEAR, ANALOG-TO-DIGITAL
CONVERTER, VIDEO, 8-BIT,
MONOLITHIC SILICON
DRAWING APPROVAL DATE
92-03-25
AMSC N/A
REVISION LEVEL
G
SIZE
A
CAGE CODE
5962-90927
67268
SHEET
1
OF
14
DSCC FORM 2233
APR 97
5962-E053-05
1. SCOPE
1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M)
and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or
Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN.
1.2 PIN. The PIN is as shown in the following example:
5962
-
90927
01
Q
X
A
Federal
stock class
designator
\
RHA
designator
(see 1.2.1)
Device
type
(see 1.2.2)
Device
class
designator
(see 1.2.3)
Case
outline
(see 1.2.4)
Lead
finish
(see 1.2.5)
/
\/
Drawing number
1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are
marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A
specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device types. The device types identify the circuit function as follows:
Device type
Generic number
Circuit function
INL/DNL (TA = +25°C)
01
02
03
AD9048T
AD9048S
TS83048
8-bit video analog-to-digital converter
8-bit video analog-to-digital converter
8-bit video analog-to-digital converter
0.5 LSB
0.75 LSB
0.65 LSB
1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as
follows:
Device class
M
Device requirements documentation
Vendor self-certification to the requirements for MIL-STD-883 compliant, non-
JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A
Q or V
Certification and qualification to MIL-PRF-38535
1.2.4 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows:
Outline letter
Descriptive designator
Terminals
Package style
X
3
See figure 1
CQCC1-N28
28
28
Dual-in-line, side brazed
Square leadless chip carrier
1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535,
appendix A for device class M.
SIZE
STANDARD
5962-90927
A
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
G
SHEET
2
DSCC FORM 2234
APR 97
1.3 Absolute maximum ratings. 1/
V
CC to DGND............................................................................................. -0.5 V dc to +7.0 V dc
AGND to DGND........................................................................................ -0.5 V dc to +0.5 V dc
EE to AGND............................................................................................. +0.5 V dc to -7.0 V dc
V
VIN, VRT or VRB to AGND ........................................................................... +0.5 V to VEE
Differential reference voltage (VRT to VRB)................................................. -2.2 V dc to +2.2 V dc
CONV, NMINV or NLINV to DGND........................................................... -0.5 V dc to +5.5 V dc
Applied output voltage to DGND............................................................... -0.5 V dc to +5.5 V dc 2/
Applied output current, externally forced................................................... -1.0 mA to +6.0 mA 3/,4/
Output short-circuit duration...................................................................... 1.0 s 5/
Junction temperature ................................................................................ +175°C
Thermal resistance, junction-to-case (θJC)
Case outline X ....................................................................................... 15°C/W
Case outline 3........................................................................................ 21°C/W
Lead temperature, (soldering, 10 sec) ...................................................... +300°C
Storage temperature range....................................................................... -65°C to +150°C
1.4 Recommended operating conditions.
Ambient operating temperature range (TA) ............................................... -55°C to +125°C
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883
-
Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents are available online at http://assist.daps.dla.mil/quicksearch/ or http://assist.daps.dla.mil or
from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of
this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
________
1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
2/ Applied voltage must be current-limited to specified range.
3/ Forcing voltage must be limited to specified range.
4/ Current is specified as a negative when flowing into the device.
5/ Output High; one pin to ground; one second duration.
SIZE
STANDARD
5962-90927
A
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
G
SHEET
3
DSCC FORM 2234
APR 97
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with
MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for
device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified
herein.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in
MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.2.3 Block diagram. The block diagrams shall be as specified on figure 3.
3.2.4 Output circuit. The output circuit shall be as specified on figure 4.
3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the
electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full
ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table I.
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be
marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer
has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be
marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be
in accordance with MIL-PRF-38535, appendix A.
3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in
MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.
3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535
listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of
compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see
6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this
drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and
herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein.
3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for
device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing.
3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2
herein) involving devices acquired to this drawing is required for any change that affects this drawing.
3.9 Verification and review for device class M. For device class M, DSCC, DSCC's agent, and the acquiring activity retain the
option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made
available onshore at the option of the reviewer.
3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in
microcircuit group number 57 (see MIL-PRF-38535, appendix A).
SIZE
STANDARD
5962-90927
A
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
G
SHEET
4
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics.
Test
Symbol
+ICC
Conditions
Group A
Device
type
Limits
Unit
mA
mA
subgroups
-55°C ≤ TA ≤ +125°C
VCC = 5.0 V, VEE = -5.2 V
unless otherwise specified
Min
Max
56
58
46
48
110
120
110
120
60
Positive supply current
Negative supply current
1/, 2/
1
2, 3
1
2, 3
1
2, 3
1
2, 3
1
2, 3
1
2, 3
1, 2, 3
01, 02
03
1/, 2/, 3/
1/, 2/
-ICC
01, 02
03
1/, 2/, 4/
1/, 3/, 4/, 5/
1/, 6/
Analog input bias current
Analog input resistance
IB
RI
All
µA
kΩ
Ω
100
All
200
40
30
Reference ladder
resistance
Reference ladder current
Invert input logic "0"
current
RR
1/
01, 02
03
All
01, 02
03
01, 02
03
125
205
40
200
400
750
250
10
125
IRC
IIL
1/, 7/
1, 2, 3
1, 2, 3
mA
1/, 3/, 7/, 8/
µA
Invert input logic "1"
current
IIH
1/, 3/, 7/, 9a/, 9b/
1/, 3/, 7/, 9a/
1/, 3/, 7/, 9b/
1, 2, 3
1, 2, 3
µA
Digital output logic "0"
voltage
VOL
1/, 4/, 10/, 11/
1, 2, 3
All
0.5
V
Digital output logic "1"
Short circuit current 12/
Conversion rate
VOH
IOS
FS
1/, 10/, 11/
1/, 3/, 7/, 13/
1/, 7/, 11/, 14/
1, 2, 3
1, 2, 3
9
All
All
01, 02
03
2.4
-175
35
V
mA
MSPS
-30
50
Transient response
1/, 13/, 14/, 15/, 27/
1/, 13/, 14/, 15/
1/, 3/, 7/, 8/
9
01, 02
03
All
20
20
500
ns
µA
µA
Convert input logic “0”
current
IIL
1, 2, 3
Convert input logic”1”
current
IIH
1/, 3/, 7/, 9a/, 9b/
1/, 3/, 7/, 9a/
1/, 3/, 7/ 9b/
1, 2, 3
1, 2, 3
1, 2
3
01, 02
03
150
250
40
10
Convert pulse width 14/
(low)
tPWL
tPWH
1/
1/
9
All
All
18
10
ns
ns
Convert pulse width 14/
(high)
9
See footnotes at end of table.
SIZE
STANDARD
5962-90927
A
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
G
SHEET
5
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics - continued.
Test
Symbol
SNR
Conditions
Group A
Device
type
Limits
Unit
dB
subgroups
-55°C ≤ TA ≤ +125°C
VCC = 5.0 V, VEE = -5.2 V
unless otherwise specified
Min
45
Max
Signal-to-noise ratio
AIN = 1.248 MHz, 15/, 16/,
TA = +25°C
AIN = 2.438 MHz, 15/, 16/,
TA = +25°C
AIN = 1.248 MHz, 15/, 17/,
TA = +25°C
AIN = 2.438 MHz, 15/, 17/,
TA = +25°C
AIN = 1.248 MHz, 15/, 16/,
TA = +25°C
AIN = 2.438 MHz, 15/, 16/,
TA = +25°C
AIN = 1.248 MHz, 15/, 17/,
TA = +25°C
AIN = 2.438 MHz, 15/, 17/,
TA = +25°C
4
4
4
01
44
54
53
02, 03
43.5
43
52.5
52
AIN = 1.248 MHz, 16/, 18/
01
02, 03
01
45
43.5
TA = +25°C
Differential linearity
Integral linearity
DNL
INL
19/
4
5, 6
4
5, 6
4
5, 6
4
5, 6
4
5, 6
4
5, 6
4, 5, 6
4, 5, 6
0.5
0.75
0.75
1.0
0.65
0.75
0.5
0.75
0.75
1.0
0.65
0.75
LSB
LSB
02
03
01
02
03
19/
No missing codes
Top of reference ladder
offset
Bottom of reference ladder
offset
QMISS
EOT
19/
19/, 20/
All
01, 02
03
01, 02
03
PASS/FAIL
mV
12
20
8
EOB
VIH
VIL
19/, 21/
19/, 22/
19/, 22/
4, 5, 6
4, 5, 6
4, 5, 6
mV
V
10
Convert input logic "1"
voltage
All
2.0
Convert input logic "0"
voltage
All
0.8
V
See footnotes at end of table.
SIZE
STANDARD
5962-90927
A
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
G
SHEET
6
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics - continued.
Test
Symbol
Conditions
Group A
Device
type
Limits
Unit
subgroups
-55°C ≤ TA ≤ +125°C
VCC = 5.0 V, VEE = -5.2
unless otherwise specified
1/, 3/, 7/, 14/, 23/, 24/
1/, 14/, 23/, 25/
1/, 14/, 23/, 25/
1/, 3/, 4/, 14/, 23/, 24/
Min
Max
15
9
Output propagation delay
Output rise time
Output fall time
tPD
tR
tF
9
9
9
9
All
All
All
01, 02
03
ns
ns
ns
ns
14
Output hold time
tOH
5
4
Output time skew
In-band harmonics
tS
1/
9
4
All
01
02
03
7
ns
dBc
49
47
47
TA = +25°C, 1/, 26/
TA = +25°C, 1/, 26/, 27/
1/ Differential reference voltage = 2.0 V.
2/ Tested worst case with all outputs low, and all digital inputs at logic "0".
3/ VCC = 5.5 V.
4/ VEE = -5.5 V.
5/ Measured with VIN = 0V and CONVERT low.
6/ Calculate dV/dI. Measure input current at AIN = +VRT and -VRB for dI.
7/ VEE = -4.9 V.
8/ Tested logic "0" = 0.4 V.
9a/ Tested logic "1" = 2.4 V.
9b/ Tested logic "1" = 5.5 V.
10/ Output Logic "0" voltage measured at 10 mA current sink. Output Logic "1" voltage measured at 0.7 mA current source.
11/ VCC = 4.5 V.
12/ The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used
for these limits.
13/ Single output at logic high to ground, one second duration maximum.
14/ See figure 5.
15/ Measured at 20 MSPS encode rate with analog input 1 dB below full scale.
16/ RMS signal to RMS noise.
17/ Peak signal to RMS noise.
18/ Measured at 35 MSPS encode rate with analog input 1 dB below full scale.
19/ VCC = 5.0 V nominal, VEE = -5.2 V nominal, differential reference voltage = 2.0 V, +VREF = 0 V, -VREF = -2.0 V.
20/ VIN = midpoint of code 0.
21/ VIN = midpoint of code 255.
22/ Tested as Pass/Fail.
23/ Outputs terminated as shown in Figure 4.
24/ Measured from the 50% point of rising convert to 50% point of output data.
25/ Measured from output signal from 10% to 90% on all bits.
26/ Measured with analog input 1 dB below full scale.
27/ Parameter is guaranteed, but not tested.
SIZE
STANDARD
5962-90927
A
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
G
SHEET
7
DSCC FORM 2234
APR 97
Inches
Max
Millimeters
Inches
Max
.100 BSC
Millimeters
Min Max
2.54 BSC
Ltr
A
Min
Min
Max
Ltr
e
Min
.225
.023
.085
.015
1.490
.610
.620
5.72
.58
b
.014
.038
.008
.36
.97
.20
L
.125
.200
3.18
5.08
b1
C
2.16
.38
L1
Q
s
.150
.015
3.81
.38
.080
.100
2.03
2.54
D
37.85
15.49
15.75
E
.500
.590
12.70
14.99
s1
s2
.005
.005
.13
.13
E1
NOTE:
The US government preferred system of measurement is the metric SI system. However, since this item was originally
designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the
inch-pound units shall take precedence.
FIGURE 1. Case outline.
SIZE
STANDARD
5962-90927
A
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
G
SHEET
8
DSCC FORM 2234
APR 97
Device type
Case outline
01, 02, 03
X, 3
Terminal number Terminal symbol
1
2
D1 (MSB)
D2
3
D3
4
D4
5
6
DGND
VCC
7
VEE
8
VEE
9
VEE
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
VCC
DGND
NLINV
D5
D6
D7
D8 (LSB)
CONVERT
RT
AGND
NC
NC
NC
VIN
NC
AGND
RB
RM
NMINV
FIGURE 2. Terminal connections.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-90927
A
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
G
SHEET
9
DSCC FORM 2234
APR 97
FIGURE 3. Block diagram.
SIZE
STANDARD
5962-90927
A
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
G
SHEET
10
DSCC FORM 2234
APR 97
FIGURE 4. Output circuit.
FIGURE 5. Timing waveforms.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-90927
A
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
G
SHEET
11
DSCC FORM 2234
APR 97
4. VERIFICATION
4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with
MIL-PRF-38535 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan
shall not affect the form, fit, or function as described herein. For device class M, sampling and inspection procedures shall be in
accordance with MIL-PRF-38535, appendix A.
4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and shall be conducted
on all devices prior to qualification and technology conformance inspection. For device class M, screening shall be in
accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection.
4.2.1 Additional criteria for device class M.
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition A, B, C or D. The test circuit shall be maintained by the manufacturer under document revision
level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in
method 1015.
(2) TA = +125°C, minimum.
b. Interim and final electrical test parameters shall be as specified in table II herein.
4.2.2 Additional criteria for device classes Q and V.
a. The burn-in test duration, test condition and test temperature, or approved alternatives shall be as specified in the
device manufacturer's QM plan in accordance with MIL-PRF-38535. The burn-in test circuit shall be maintained under
document revision level control of the device manufacturer's Technology Review Board (TRB) in accordance with
MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in
method 1015 of MIL-STD-883.
b. Interim and final electrical test parameters shall be as specified in table II herein.
c. Additional screening for device class V beyond the requirements of device class Q shall be as specified in
MIL-PRF-38535, appendix B.
4.3 Qualification inspection for device classes Q and V. Qualification inspection for device classes Q and V shall be in
accordance with MIL-PRF-38535. Inspections to be performed shall be those specified in MIL-PRF-38535 and herein for groups
A, B, C, D, and E inspections (see 4.4.1 through 4.4.4).
4.4 Conformance inspection. Technology conformance inspection for classes Q and V shall be in accordance with
MIL-PRF-38535 including groups A, B, C, D, and E inspections and as specified herein. Quality conformance inspection for
device class M shall be in accordance with MIL-PRF-38535, appendix A and as specified herein. Inspections to be performed
for device class M shall be those specified in method 5005 of MIL-STD-883 and herein for groups A, B, C, D, and E inspections
(see 4.4.1 through 4.4.4).
4.4.1 Group A inspection.
a. Tests shall be as specified in table II herein.
b. Subgroups 7, 8, 10, and 11 in table I, method 5005 of MIL-STD-883 shall be omitted.
SIZE
STANDARD
5962-90927
A
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
G
SHEET
12
DSCC FORM 2234
APR 97
TABLE II. Electrical test requirements.
Subgroups
Subgroups
(in accordance with
(in accordance with
Test requirements
MIL-STD-883,
MIL-PRF-38535, table III)
method 5005, table I)
Device
Device
class Q
Device
class V
class M
Interim electrical
1
1
1
parameters (see 4.2)
Final electrical
1/ 1, 2, 3, 4,
5, 6, 9
1/ 1, 2, 3, 4,
5, 6, 9
1/ 1, 2, 3, 4, 5, 6, 9
parameters (see 4.2)
Group A test
1, 2, 3, 4, 5, 6,
9
1, 2, 3, 4, 5,
6, 9
1, 2, 3, 4, 5, 6, 9
requirements (see 4.4)
Group C end-point electrical
parameters (see 4.4)
Group D end-point electrical
parameters (see 4.4)
Group E end-point electrical
parameters (see 4.4)
1
1
1
1
1
1
1
1
1
1/ PDA applies to subgroup 1.
4.4.2 Group C inspection. The group C inspection end-point electrical parameters shall be as specified in table II herein.
4.4.2.1 Additional criteria for device class M. Steady-state life test conditions, method 1005 of MIL-STD-883:
a. Test condition A, B, C or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the
inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of
MIL-STD-883.
b. TA = +125°C, minimum.
c. Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
4.4.2.2 Additional criteria for device classes Q and V. The steady-state life test duration, test condition and test temperature,
or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The
test circuit shall be maintained under document revision level control by the device manufacturer's TRB in accordance with
MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the
inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-
883.
4.4.3 Group D inspection. The group D inspection end-point electrical parameters shall be as specified in table II herein.
4.4.4 Group E inspection. Group E inspection is required only for parts intended to be marked as radiation hardness assured
(see 3.5 herein).
a. End-point electrical parameters shall be as specified in table II herein.
b. For device classes Q and V, the devices or test vehicle shall be subjected to radiation hardness assured tests as
specified in MIL-PRF-38535 for the RHA level being tested. For device class M, the devices shall be subjected to
radiation hardness assured tests as specified in MIL-PRF-38535, appendix A for the RHA level being tested. All device
classes must meet the postirradiation end-point electrical parameter limits as defined in table I at TA = +25°C ±5°C,
after exposure, to the subgroups specified in table II herein.
SIZE
STANDARD
5962-90927
A
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
G
SHEET
13
DSCC FORM 2234
APR 97
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535 for device classes
Q and V or MIL-PRF-38535, appendix A for device class M.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.1.1 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor
prepared specification or drawing.
6.1.2 Substitutability. Device class Q devices will replace device class M devices.
6.2 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for
the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal.
6.3 Record of users. Military and industrial users should inform Defense Supply Center Columbus (DSCC) when a system
application requires configuration control and which SMD's are applicable to that system. DSCC will maintain a record of users
and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic
devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0544.
6.4 Comments. Comments on this drawing should be directed to DSCC-VA , Columbus, Ohio 43218-3990, or telephone
(614) 692-0547.
6.5 Abbreviations, symbols, and definitions. The abbreviations, symbols, and definitions used herein are defined in
MIL-PRF-38535 and MIL-HDBK-1331.
6.6 Sources of supply.
6.6.1 Sources of supply for device classes Q and V. Sources of supply for device classes Q and V are listed in QML-38535.
The vendors listed in QML-38535 have submitted a certificate of compliance (see 3.6 herein) to DSCC-VA and have agreed to
this drawing.
6.6.2 Approved sources of supply for device class M. Approved sources of supply for class M are listed in MIL-HDBK-103.
The vendors listed in MIL-HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been
submitted to and accepted by DSCC-VA.
SIZE
STANDARD
5962-90927
A
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
G
SHEET
14
DSCC FORM 2234
APR 97
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 04-12-20
Approved sources of supply for SMD 5962-90927 are listed below for immediate acquisition information only and shall
be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised
to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate
of compliance has been submitted to and accepted by DSCC-VA. This information bulletin is superseded by the next
dated revision of MIL-HDBK-103 and QML-38535. DSCC maintains an online database of all current sources of
supply at http://www.dscc.dla.mil/Programs/Smcr/.
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
Vendor
similar
PIN 2/
number
5962-9092701MXA
5962-9092701M3A
5962-9092702MXA
5962-9092702M3A
5962-9092703MXA
596209092703M3A
24355
24355
24355
24355
F8385
F8385
AD9048TQ/883B
AD9048TE/883B
AD9048SQ/883B
AD9048SE/883B
TS83048MCB/C
TS83048ME1B/C
1/ The lead finish shown for each PIN representing
a hermetic package is the most readily available
from the manufacturer listed for that part. If the
desired lead finish is not listed contact the vendor
to determine its availability.
2/ Caution. Do not use this number for item
acquisition. Items acquired to this number may not
satisfy the performance requirements of this drawing.
Vendor CAGE
number
Vendor name
and address
24355
Analog Devices
Rt 1 Industrial Park
PO Box 9106
Norwood, MA 02062
Point of contact:
7910 Triad Center Drive
Greensboro, NC 27409-9605
F8385
Atmel Grenoble
Avenue De Rochepleine
Saint Egreve F-38120, France
Point of contact:
Thales Components Corp. (18778)
40G Commerce Way
Totowa, NJ 07511-0540
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.
相关型号：
AD9048SQ/883B
IC 1-CH 8-BIT FLASH METHOD ADC, PARALLEL ACCESS, CDIP28, CERDIP-28, Analog to Digital Converter
ADI
AD9048TQ/833B
IC 1-CH 8-BIT FLASH METHOD ADC, PARALLEL ACCESS, CDIP28, CERAMIC, SIDE BRAZED, DIP-28, Analog to Digital Converter
ADI
AD9048TQ/883B
IC 1-CH 8-BIT FLASH METHOD ADC, PARALLEL ACCESS, CDIP28, CERDIP-28, Analog to Digital Converter
ADI
©2020 ICPDF网 联系我们和版权申明