AD9525 [ADI]
Low Jitter Clock Generator with Eight LVPECL Outputs; 低抖动时钟发生器,八LVPECL输出型号: | AD9525 |
厂家: | ADI |
描述: | Low Jitter Clock Generator with Eight LVPECL Outputs |
文件: | 总48页 (文件大小:1303K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Low Jitter Clock Generator
with Eight LVPECL Outputs
Data Sheet
AD9525
FEATURES
FUNCTIONAL BLOCK DIAGRAM
Integrated ultralow noise synthesizer
8 differential 3.6 GHz LVPECL outputs and 1 LVPECL SYNC
output or 2 CMOS SYNC outputs
2 differential reference inputs and 1 single-ended reference
input
REFA
REFA
AD9525
REFB
REFB
SYNC_OUT
÷S
PLL
SYNC_OUT
OUT7
OUT7
REFC
APPLICATIONS
OUT6
OUT6
LTE and multicarrier GSM base stations
Clocking high speed ADCs, DACs
ATE and high performance instrumentation
40/100 Gb/sec OTN line side clocking
Cable/DOCSIS CMTS clocking
OUT5
OUT5
OUT4
OUT4
CLKIN
CLKIN
DIVIDERS
Test and measurement
OUT3
OUT3
OUT2
OUT2
OUT1
OUT1
SPI CONTROL
OUT0
OUT0
Figure 1.
GENERAL DESCRIPTION
The AD9525 is designed to support converter clock requirements
for long-term evolution (LTE) and multicarrier GSM base station
designs.
The AD9525 offers a dedicated output that can be used to provide
a programmable signal for resetting or synchronizing a data
converter. The output signal is activated by a SPI write.
The AD9525 provides a low power, multioutput, clock distribution
function with low jitter performance, along with an on-chip PLL
that can be used with an external VCO or VCXO. The VCO input
and eight LVPECL outputs can operate up to a frequency of
3.6 GHz. All outputs share a common divider that can provide
a division of 1 to 6.
The AD9525 is available in a 48-lead LFCSP and can be operated
from a single 3.3 V supply. The external VCXO or VCO can
have an operating voltage of up to 5.5 V.
The AD9525 operates over the extended industrial temperature
range of −40°C to +85°C.
Rev. 0
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Technical Support
©2012 Analog Devices, Inc. All rights reserved.
www.analog.com
AD9525
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Absolute Maximum Ratings ......................................................... 12
Thermal Resistance.................................................................... 12
ESD Caution................................................................................ 12
Pin Configuration and Function Descriptions........................... 13
Typical Performance Characteristics ........................................... 15
Terminology.................................................................................... 18
Detailed Block Diagram ................................................................ 19
Theory of Operation ...................................................................... 20
Configuration of the PLL .......................................................... 20
Clock Distribution ..................................................................... 23
SYNC_OUT ................................................................................ 23
Reset Modes ................................................................................ 25
Power-Down Modes .................................................................. 26
Serial Control Port ......................................................................... 27
Pin Descriptions ......................................................................... 27
General Operation of Serial Control Port............................... 27
The Instruction Word (16 Bits)................................................ 28
MSB/LSB First Transfers ........................................................... 28
Control Registers ............................................................................ 31
Control Register Map Overview .............................................. 31
Register Map Descriptions............................................................ 33
Applications Information.............................................................. 45
Frequency Planning Using the AD9525.................................. 45
Using the AD9525 Outputs for ADC Clock Applications.... 45
LVPECL Clock Distribution..................................................... 46
SYNC_OUT Distribution ......................................................... 46
Outline Dimensions....................................................................... 47
Ordering Guide............................................................................... 47
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description......................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Conditions..................................................................................... 3
Supply Current.............................................................................. 3
Power Dissipation......................................................................... 3
REFA and REFB Input Characteristics...................................... 4
REFC Input Characteristics ........................................................ 4
Clock Inputs .................................................................................. 5
PLL Characteristics ...................................................................... 5
PLL Digital Lock Detect .............................................................. 6
Clock Outputs............................................................................... 6
Timing Characteristics ................................................................ 7
Clock Output Absolute Time Jitter (Clock Generation
Using External 122.88 MHz VCXO).......................................... 8
Clock Output Absolute Time Jitter (Clock Generation
Using External 1475 MHz VCO) ............................................... 8
Clock Output Absolute Time Jitter (Clock Generation
Using External 2.05 GHz VCO) ................................................. 9
Clock Output Absolute Time Jitter (Clock Generation
Using External 3 GHz VCO) ...................................................... 9
Clock Output Additive Phase Noise (Distribution Only;
Clock Input to Distribution Output, Including VCO
Divider).......................................................................................... 9
PD RESET
,
, and REF_SEL Pins................................................ 10
STATUS and REF_MON Pins .................................................. 10
Serial Control Port ..................................................................... 11
REVISION HISTORY
10/12—Revision 0: Initial Version
Rev. 0 | Page 2 of 48
Data Sheet
AD9525
SPECIFICATIONS
Typical is given for VDD3 = 3.3 V 5%; VDD3 ≤ VDD_CP ≤ 5.25 V; TA = 25°C; OUT_RSET resistor = 4.12 kΩ; CP_RSET resistor (CPRSET) =
5.1 kΩ, unless otherwise noted. Minimum and maximum values are given over full VDD3 and TA (−40°C to +85°C) variation as listed in Table 1.
REFA at 122.88 MHz, CLKIN frequency = 2949.12 MHz.
CONDITIONS
Table 1.
Parameter
Min
Typ Max
Unit
Test Conditions/Comments
SUPPLY VOLTAGE
VDD3
3.3
V
3.3 V 5%
VDD_CP
VDD3
5.25
4.12
5.1
V
Nominally 3.3 V to 5.0 V 5%
Sets internal biasing currents; connect to ground
OUT_RSET PIN RESISTOR
CP_RSET PIN RESISTOR (CPRSET RESISTOR)
kΩ
kΩ
Sets internal CP current range, nominally 4.8 mA
(CP_LSB = 600 µA); actual current calculated by
CP_LSB = 3.06/CPRSET, connect to ground; CPRSET
range = 2.7 kΩ to10 kΩ
TEMPERATURE RANGE, TA
−40
+25 +85
°C
SUPPLY CURRENT
Table 2.
Parameter
Min Typ
Max
Unit
Test Conditions/Comments
SUPPLY CURRENT FOR VDD3 and VDD_CP PINS
fCLK = 2949.12 MHz; REFA and REFB enabled
at 122.88 MHz; R dividers = 2; M divider = 2;
PFD = 61.44 MHz; eight LVPECL outputs at
1474.56 MHz; LVPECL 780 mV mode
VDD3 (Pin 3, Pin 36, Pin 41, Pin 46), Total Supply
Voltage for Outputs
VDD3 (Pin 9), Supply Voltage for M Divider,
CLK Inputs and Distribution
310
98
369
107
mA
mA
Outputs terminated with 50 Ω to VDD3 − 2 V
VDD_CP (Pin 13), Supply Voltage for Charge Pump
VDD3 (Pin 20), Supply Voltage for PLL
VDD3 (Pin 32), Supply Voltage for SYNC_OUT
6.6
53
45
7.6
63.4
54
mA
mA
mA
POWER DISSIPATION
Table 3.
Parameter
Min Typ
Max
Unit
Test Conditions/Comments
POWER DISSIPATION, CHIP
Does not include power dissipated in external
resistors; all LVPECL outputs terminated with
50 Ω to VDD3 − 2 V; LVPECL 780 mV mode
Power-On Default
Typical Operation 1
782
1.15
871
1.23
mW
W
No programming; default register values
fCLK = 2949.12 MHz; REFA and REFB enabled
at 122.88 MHz; R dividers = 2; M divider = 2;
PFD = 61.44 MHz; eight LVPECL outputs at
1474.56 MHz
Typical Operation 2
1.17
1.25
W
fCLK = 2949.12 MHz; PLL on; REFA enabled at
122.88 MHz; M divider = 1; PFD = 122.88MHz;
eight LVPECL outputs at 2949.12 MHz
PD Power-Down
51
56.4
19.1
mW
mW
PD pin pulled low
PD Power-Down, Maximum Sleep
13.2
PD pin pulled low; power-down distribution
reference, Reg. 0x230[1] = 1b; note that powering
down distribution reference disables safe power-
down mode (see Power-Down Modes section)
VDD_CP Supply
22
25
mW
PLL operating; typical closed-loop configuration
Rev. 0 | Page 3 of 48
AD9525
Data Sheet
Parameter
Min Typ
Max
Unit
Test Conditions/Comments
POWER DELTAS, INDIVIDUAL FUNCTIONS
M Divider On/Off
P Divider On/Off
B Divider On/Off
REFB On
Power delta when a function is enabled/disabled
M divider bypassed
P divider bypassed
B divider bypassed
Delta from powering down REFB differential input
5
3
16
15
254
8.7
5.7
23.1
25
mW
mW
mW
mW
PLL On/Off
300.5 mW
PLL off to PLL on, normal operation; no reference
enabled
One Channel, One Driver
One Channel, Two Drivers
159
288
184
337
mW
mW
No LVPECL output on to one LVPECL output on
at 2949.12 MHz; same output pair
No LVPECL output on to two LVPECL outputs on
at 2949.12 MHz; same output pair
REFA AND REFB INPUT CHARACTERISTICS
Table 4.
Parameter
Min Typ
Max
Unit
Test Conditions/Comments
DIFFERENTIAL MODE (REFA, REFA; REFB, REFB)
Differential mode (can accommodate single-
ended input by ac grounding unused input)
Input Frequency
0
500
MHz
Frequencies below ~1 MHz should be dc-coupled;
be careful to match self-bias voltage
Input Sensitivity
200
1.52 1.65
1.38 1.50
mV p-p Frequency at 122.88 MHz
Self-Bias Voltage, REFA and REFB
Self-Bias Voltage, REFA and REFB
Input Resistance, REFA and REFB
Input Resistance, REFA and REFB
1.78
1.61
4.9
V
V
Self-bias voltage of REFA and REFB inputs1
Self-bias voltage of REFA and REFB inputs1
4.5
4.9
4.7
5.2
kΩ
kΩ
Self-biased1
Self-biased1
5.4
DUTY CYCLE
Duty cycle bounds are set by pulse width high and
pulse width low
Pulse Width Low
Pulse Width High
500
500
ps
ps
1
REFA
, REFB and
REFB
self-bias points are offset slightly to avoid chatter on an open input condition.
The differential pairs of REFA and
REFC INPUT CHARACTERISTICS
Table 5.
Parameter
Min Typ
Max
300
0.8
Unit
Test Conditions/Comments
REFC INPUT
Input Frequency Range
Input High Voltage
Input Low Voltage
Input Current
Duty Cycle
MHz
V
V
DC-coupled input (not self-biased)
2.0
1
µA
Duty cycle bounds are set by pulse width high and
pulse width low
Pulse Width Low
Pulse Width High
1
1
ns
ns
Rev. 0 | Page 4 of 48
Data Sheet
AD9525
CLOCK INPUTS
Table 6.
Parameter
Min Typ
Max
Unit
Test Conditions/Comments
Input Frequency
0
3.6
GHz
Frequencies below ~1 MHz should be dc-coupled; be careful to
match self-bias voltage
Input Sensitivity
Input Level
150
mV p-p Measured at 3.1 GHz
2
V p-p
Larger voltage swings can turn on the protection diodes and
can degrade jitter performance
Self-biased; enables ac coupling
With 200 mV p-p signal applied; dc-coupled
Self-biased
Input Common-Mode Voltage, VCM
Input Common-Mode Range, VCMR
Input Resistance
1.55 1.64
1.3
1.74
1.8
7.4
V
V
kΩ
pF
6.7
7
2
Input Capacitance
PLL CHARACTERISTICS
Table 7.
Parameter
Min Typ
Max
Unit
Test Conditions/Comments
PHASE/FREQUENCY DETECTOR (PFD)
PFD Input Frequency
125
45
MHz
MHz
Antibacklash pulse width = 1.3 ns, 2.9 ns
Antibacklash pulse width = 6.0 ns
CHARGE PUMP (CP)
VDD_CP (Pin 13); VCP is the voltage of the charge pump pin
( C P, Pin 14)
ICP Sink/Source
High Value
Programmable
With CPRSET = 5.1 kΩ; higher ICP is possible by changing
CPRSET; VCP = VDD_CP/2 V
With CPRSET = 5.1 kΩ; lower ICP is possible by changing
CPRSET, VCP = VDD_CP/2 V
4.5
4.9
5.4
mA
mA
Low Value
0.57 0.61
0.67
Absolute Accuracy
CPRSET Range
ICP High Impedance Mode Leakage
Sink-and-Source Current Matching
ICP vs. VCP
2.5
%
VCP = VDD_CP/2 V
2.7
3.5
2
10
kΩ
µA
%
%
%
VDD_CP = 5 V
0.5 V < VCP < VDD_CP − 0.5 V
0.5 V < VCP < VDD_CP − 0.5 V
VCP = VDD_CP/2 V
1.5
2
ICP vs. Temperature
P DIVIDER (PART OF N DIVIDER)
Input Frequency P = 1
Input Frequency P = 2
Input Frequency P = 3
Input Frequency P = 4
Input Frequency P = 5
Input Frequency P = 6
B DIVIDER (PART OF N DIVIDER)
Input Frequency
1500 MHz
3000 MHz
3600 MHz
3600 MHz
3600 MHz
3600 MHz
1500 MHz
3600 MHz
B counter input frequency (N Divider input frequency
divided by P)
M DIVIDER
Input Frequency
NOISE CHARACTERISTICS
In-Band Phase Noise of the Charge Pump/
Phase Frequency Detector (In-Band
Means Within the LBW of the PLL)
PLL in-band phase noise floor is estimated by measuring the
in-band phase noise at the output of the VCO and subtracting
20 log(N) (where N is the value of the N divider)
At 61.44 MHz PFD Frequency
At 122.88 MHz PFD Frequency
PLL Figure of Merit (FOM)
−144
−141
−222
dBc/Hz
dBc/Hz
dBc/Hz Reference slew rate > 0.25 V/ns; FOM +10 log (fPFD) is an
approximation of the PFD/CP in-band phase noise (in the
flat region) inside the PLL loop bandwidth; when running
closed loop, the phase noise, as observed at the VCO output,
is increased by 20 log(N)
Rev. 0 | Page 5 of 48
AD9525
Data Sheet
PLL DIGITAL LOCK DETECT
Table 8.
Parameter
PLL DIGITAL LOCK DETECT WINDOW1
Min
Typ
Max
Unit
Test Conditions/Comments
Signal available at the STATUS and REF_MON pins when
selected by appropriate register settings; lock detect window
settings can be varied by changing the CPRSET resistor
Lock Threshold (Coincidence of Edges)
Selected by Reg. 0x010[1:0] and Reg. 0x019[1], which is the
threshold for transitioning from unlock to lock
Low Range (ABP 1.3 ns, 2.9 ns)
High Range (ABP 1.3 ns, 2.9 ns)
High Range (ABP 6.0 ns)
4
7
3.5
ns
ns
ns
Reg. 0x010[1:0] = 00b, 01b,11b; Reg. 0x019[1] = 1b
Reg. 0x010[1:0] = 00b, 01b, 11b; Reg. 0x019[1] = 0b
Reg. 0x010[1:0] = 10b; Reg. 0x019[1] = 0b
Selected by Reg. 0x017[1:0] and Reg. 0x019[1], which is the
threshold for transitioning from unlock to lock
Unlock Threshold (Hysteresis)1
Low Range (ABP 1.3 ns, 2.9 ns)
High Range (ABP 1.3 ns, 2.9 ns)
High Range (ABP 6.0 ns)
8.3
16.9
11
ns
ns
ns
Reg. 0x010[1:0] = 00b, 01b, 11b; Reg. 0x019[1] = 1b
Reg. 0x010[1:0] = 00b, 01b, 11b; Reg. 0x019[1] = 0b
Reg. 0x010[1:0] = 10b; Reg. 0x019[1] = 0b
1 For reliable operation of the digital lock detect, the period of the PFD frequency must be greater than the unlock-after-lock time.
CLOCK OUTPUTS
Table 9.
Parameter
Min
Typ
Max
Unit Test Conditions/Comments
LVPECL CLOCK OUTPUTS
Output Frequency, Maximum
Rise Time/Fall Time (20% to 80%)
Duty Cycle
3.6
GHz
ps
105
162
Input duty cycle = 50/50
M = 1
47
45
47
45
32
750
50
50
49
49
32
830
53
55
51
55
33
984
%
%
%
%
%
mV
FOUT = 2800 MHz
FOUT < 3000 MHz
FOUT = 1400 MHz
FOUT < 1500 MHz
FOUT = 933.33 MHz
Voltage across pins, output driver static;
Termination = 50 Ω to VDD3 − 2 V
M = 2, 4, 6
M = 3, 5
Output Differential Voltage,
Magnitude
Common-Mode Output Voltage
VDD3 –
1.42
VDD3 –
1.37
VDD3 –
1.32
V
Output driver static; VDD3 (Pin 3, Pin 36, Pin 41, Pin 46);
Termination = 50 Ω to VDD3 − 2 V
Rev. 0 | Page 6 of 48
Data Sheet
AD9525
TIMING CHARACTERISTICS
Table 10.
Parameter
Min
Typ Max
Unit
Test Conditions/Comments
PROPAGATION DELAY, tPECL, CLKIN TO LVPECL OUTPUT
For All M Divider Values
Variation with Temperature
OUTPUT SKEW, LVPECL OUTPUTS1
All LVPECL Outputs
Termination as shown in Figure 35
High frequency clock distribution configuration
461
522 600
388
ps
fs/°C
13.5 25.2
ps
Across temperature and VDD per device
Temperature Coefficient
14
fs/°C
ps
All LVPECL Outputs Across Multiple Parts
OUTPUT SKEW, LVPECL-TO-SYNC_OUT1
SYNC_OUT LVPECL Mode
144
All LVPECL Outputs
Temperature Coefficient
All LVPECL Outputs Across Multiple Parts
SYNC_OUT CMOS Mode
189 298
543
ps
fs/°C
ps
Across temperature and VDD per device
417
All LVPECL Outputs
All LVPECL Outputs Across Multiple Parts
PROPAGATION DELAY, REF TO LVPECL OUTPUT
1.64 2.34
2.46
ns
ns
ps
Across temperature and VDD per device
267
581 924
REF refers to either REFA/REFA or REFB/REFB pairs
1 The output skew is the difference between any two paths while operating at the same voltage and temperature.
Timing Diagrams
tCLK
CLK
DIFFERENTIAL
80%
tPECL
LVPECL
20%
tCMOS
tRP
tFP
Figure 3. LVPECL Timing, Differential
CLK
Figure 2. CLK/
to Clock Output Timing, M Divider = 1
Rev. 0 | Page 7 of 48
AD9525
Data Sheet
CLOCK OUTPUT ABSOLUTE TIME JITTER (CLOCK GENERATION USING EXTERNAL 122.88 MHZ VCXO)
Table 11.
Parameter
Min Typ Max Unit
Test Conditions/Comments
LVPECL OUTPUT ABSOLUTE TIME JITTER
Application example based on a typical setup using
an external 122.88 MHz VCXO (Crystek CVHD-950);
reference = 122.88 MHz; R divider = 1; LBW = 40 Hz
FOUT = 122.88 MHz
FOUT = 61.44 MHz
107
69
108
107
fs rms Integration BW = 1 kHz to 40 MHz
fs rms Integration BW = 12 kHz to 20 MHz
fs rms Integration BW = 1 kHz to 20 MHz
fs rms Integration BW = 12 kHz to 20 MHz
CLOCK OUTPUT ABSOLUTE TIME JITTER (CLOCK GENERATION USING EXTERNAL 1475 MHZ VCO)
Table 12.
Parameter
Min Typ Max Unit
Test Conditions/Comments
LVPECL OUTPUT ABSOLUTE TIME JITTER
Application example based on a typical setup using
an external 1475 MHz VCO (Bowei Model MVCO-1475);
reference = 122.88 MHz; R divider = 1; PLL LBW = 18 kHz
FOUT = 1474.56 MHz
99
77
74
68
fs rms Integration BW = 1 kHz to 100 MHz
fs rms Integration BW = 10 kHz to 100 MHz
fs rms Integration BW = 10 kHz to 40 MHz
fs rms Integration BW = 12 kHz to 20 MHz
Reference Sideband Spurs
FOUT = 245.76 MHz
−93
104
87
dBc
122.88 MHz
fs rms Integration BW = 1 kHz to 100 MHz
fs rms Integration BW = 10 kHz to 100 MHz
fs rms Integration BW = 12 kHz to 20 MHz
75
Reference Sideband Spurs
−98
dBc
122.88 MHz
Table 13.
Parameter
Min Typ Max Unit
Test Conditions/Comments
LVPECL OUTPUT ABSOLUTE TIME JITTER
Application example based on a typical setup using
an external 1475 MHz VCO (Z-Communications CRO1474-LF);
reference = 122.88 MHz; R divider = 1; PLL LBW = 8 kHz
FOUT = 1474.56 MHz
72
40
33
28
fs rms Integration BW = 1 kHz to 100 MHz
fs rms Integration BW = 10 kHz to 100 MHz
fs rms Integration BW = 10 kHz to 40 MHz
fs rms Integration BW = 12 kHz to 20 MHz
Reference Sideband Spurs
FOUT = 245.76 MHz
−94
83
61
dBc
122.88 MHz
fs rms Integration BW = 1 kHz to 100 MHz
fs rms Integration BW = 10 kHz to 40 MHz
fs rms Integration BW = 12 kHz to 20 MHz
46
Reference Sideband Spurs
−93
dBc
122.88 MHz
Rev. 0 | Page 8 of 48
Data Sheet
AD9525
CLOCK OUTPUT ABSOLUTE TIME JITTER (CLOCK GENERATION USING EXTERNAL 2.05 GHZ VCO)
Table 14.
Parameter
Min Typ
Max
Unit
Test Conditions/Comments
LVPECL OUTPUT ABSOLUTE TIME JITTER
Application example based on a typical setup using
an external 2.05 MHz VCO (Bowei Model MVCO-
2050A); reference = 122.054215 MHz; R divider = 12;
PLL LBW = 5 kHz
FOUT = 2048.867 MHz
19
21
87
−105
fs rms
fs rms
fs rms
dBc
Integration BW = 200 kHz to 5 MHz
Integration BW = 200 kHz to 10 MHz
Integration BW = 12 kHz to 20 MHz
10.671MHz
Reference Sideband Spurs
CLOCK OUTPUT ABSOLUTE TIME JITTER (CLOCK GENERATION USING EXTERNAL 3 GHZ VCO)
Table 15.
Parameter
Min Typ
Max
Unit
Test Conditions/Comments
LVPECL OUTPUT ABSOLUTE TIME JITTER
Application example based on a typical setup using
an external 2950 MHz VCO (Z-Communications Model
CRO-2950); reference = 122.88 MHz; R divider = 1
FOUT = 2949.12 MHz; PLL LBW = 7 kHz
63
38
34
28
−99
62
36
31
25
−100
78
60
44
33
fs rms
fs rms
fs rms
fs rms
dBc
fs rms
fs rms
fs rms
fs rms
dBc
fs rms
fs rms
fs rms
fs rms
dBc
Integration BW = 1 kHz to 100 MHz
Integration BW = 10 kHz to 100 MHz
Integration BW = 10 kHz to 40 MHz
Integration BW = 12 kHz to 20 MHz
122.88 MHz
Integration BW = 1 kHz to 100 MHz
Integration BW = 10 kHz to 100 MHz
Integration BW = 10 kHz to 40 MHz
Integration BW = 12 kHz to 20 MHz
122.88 MHz
Integration BW = 1 kHz to 100 MHz
Integration BW = 10 kHz to 100 MHz
Integration BW = 10 kHz to 40 MHz
Integration BW = 12 kHz to 20 MHz
122.88 MHz
Reference Sideband Spurs
FOUT = 1474.56 MHz; PLL LBW = 7 kHz
Reference Sideband Spurs
FOUT = 491.52 MHz; PLL LBW = 7 kHz
Reference Sideband Spurs
−96
CLOCK OUTPUT ADDITIVE PHASE NOISE (DISTRIBUTION ONLY; CLOCK INPUT TO DISTRIBUTION OUTPUT,
INCLUDING VCO DIVIDER)
Table 16.
Parameter
Min Typ
Max
Unit
Test Conditions/Comments
CLK-TO-LVPECL ADDITIVE PHASE NOISE
CLK = 2949.12 MHz, FOUT = 2949.12 MHz
Divider = 1
Distribution section only; does not include PLL and VCO
At 10 Hz Offset
At 100 Hz Offset
At 1 kHz Offset
At 10 kHz Offset
At 100 kHz Offset
At 800 kHz Offset
At 1 MHz Offset
At 10 MHz Offset
−112
−122
−133
−141
−146
−148
−148
−149
−151
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
At 100 MHz Offset
Rev. 0 | Page 9 of 48
AD9525
Data Sheet
Parameter
Min Typ
Max
Unit
Test Conditions/Comments
CLK = 1474.56 MHz, FOUT = 1474.56 MHz
Divider = 1
At 10 Hz Offset
At 100 Hz Offset
At 1 kHz Offset
At 10 kHz Offset
At 100 kHz Offset
At 800 kHz Offset
At 1 MHz Offset
−114
−125
−134
−144
−149
−151
−151
−154
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
At 10 MHz Offset
CLK = 122.88 MHz, FOUT = 122.88 MHz
Divider = 1
At 10 Hz Offset
At 100 Hz Offset
At 1 kHz Offset
At 10 kHz Offset
At 100 kHz Offset
At 800 kHz Offset
At 1 MHz Offset
−134
−145
−153
−159
−161
−161
−161
−161
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
At 10 MHz Offset
PD, RESET, AND REF_SEL PINS
Table 17.
Parameter
Min Typ
Max
Unit
Test Conditions/Comments
INPUT CHARACTERISTICS
Logic 1 Voltage
2.0
V
Logic 0 Voltage
0.8
V
Logic 1 Current
Logic 0 Current PD, RESET
1
µA
µA
−112
The minus sign indicates that current is flowing out of
the AD9525, which is due to the internal pull-up
resistor
Logic 0 Current REF_SEL
Capacitance
1
2
µA
pF
RESET TIMING
Pulse Width Low
RESET Inactive to Start of Register
Programming
50
100
ns
ns
STATUS AND REF_MON PINS
Table 18.
Parameter
Min Typ
2.7
Max
Unit
Test Conditions/Comments
OUTPUT CHARACTERISTICS
Output Voltage High, VOH
Output Voltage Low, VOL
MAXIMUM TOGGLE RATE
1 mA output load
V
V
0.4
200
MHz
Applies when mux is set to any divider or counter
output or PFD up/down pulse; usually debug mode
only; beware that spurs can couple to output when any
of these pins is toggling
Rev. 0 | Page 10 of 48
Data Sheet
AD9525
SERIAL CONTROL PORT
Table 19.
Parameter
Min
Typ
Max
Unit
Test Conditions/Comments
CS (INPUT)
CS has an internal 30 kΩ pull-up resistor
Input Logic 1 Voltage
Input Logic 0 Voltage
Input Logic 1 Current
Input Logic 0 Current
2.0
V
V
µA
µA
0.8
2.5
−112
2
The minus sign indicates that current is flowing out of the
AD9525, which is due to the internal pull-up resistor
Input Capacitance
SCLK (INPUT)
pF
SCLK has an internal 30 kΩ pull-down resistor
Input Logic 1 Voltage
Input Logic 0 Voltage
Input Logic 1 Current
Input Logic 0 Current
Input Capacitance
SDIO (WHEN INPUT)
Input Logic 1 Voltage
Input Logic 0 Voltage
Input Logic 1 Current
Input Logic 0 Current
Input Capacitance
SDIO, SDO (OUTPUTS)
Output Logic 1 Voltage
Output Logic 0 Voltage
TIMING
2.0
2.0
2.7
V
V
µA
µA
pF
0.8
1
112
2
V
V
nA
nA
pF
0.8
10
20
2
1 mA load current
V
V
0.4
31
Clock Rate (SCLK, 1/tSCLK
Pulse Width High, tHIGH
Pulse Width Low, tLOW
SDIO to SCLK Setup, tDS
SCLK to SDIO Hold, tDH
)
MHz
ns
ns
ns
ns
16
16
2
1.1
SCLK to Valid SDIO and SDO, tDV
CS to SCLK Setup and Hold, tS, tH
12
ns
ns
2
CS Minimum Pulse Width High, tPWH 3.6
ns
Rev. 0 | Page 11 of 48
AD9525
Data Sheet
ABSOLUTE MAXIMUM RATINGS
Table 20.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Parameter
Rating
VDD3 to GND
−0.3 V to +3.6 V
VDD_CP, CP to GND
REFA, REFA, REFB, REFB, REFC to GND
OUT_RSET to GND
CP_RSET to GND
CLKIN, CLKIN to GND
CLKIN to CLKIN
−0.3 V to +5.8 V
−0.3 V to VDD3 + 0.3 V
−0.3 V to VDD3 + 0.3 V
−0.3 V to VDD3 + 0.3 V
−0.3 V to VDD3 + 0.3 V
−1.2 V to +1.2 V
THERMAL RESISTANCE
Table 21. Thermal Resistance (Simulated)
SCLK, SDIO, SDO, CS to GND
−0.3 V to VDD3 + 0.3 V
−0.3 V to VDD3 + 0.3 V
Airflow
OUT0, OUT0, OUT1, OUT1, OUT2, OUT2,
OUT3, OUT3, OUT4, OUT4, OUT5, OUT5,
OUT6, OUT6, OUT7, OUT7,
Package Velocity
1, 2
1, 3
1, 4
1, 2
Type
(m/sec)
θJA
θJC
θJB
14.7
ΨJT
0.2
0.3
0.4
Unit
°C/W
°C/W
°C/W
48-Lead
LFCSP
0
27.3
23.9
21.4
2.1
SYNC_OUT, SYNC_OUT to GND
1.0
2.5
RESET, PD, STATUS, REF_MON to GND
Junction Temperature1
−0.3 V to VDD3 + 0.3 V
150°C
1 Per JEDEC 51-7, plus JEDEC 51-5 2S2P test board.
Storage Temperature Range
Lead Temperature (10 sec)
−65°C to +150°C
300°C
2 Per JEDEC JESD51-2 (still air) or JEDEC JESD51-6 (moving air).
3 Per MIL-Std 883, Method 1012.1.
4 Per JEDEC JESD51-8 (still air).
1 See Table 21 for θJA.
ESD CAUTION
Rev. 0 | Page 12 of 48
Data Sheet
AD9525
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
2
36 VDD3
OUT7
OUT1
OUT1
35
3
VDD3
34 OUT7
4
5
OUT0
OUT0
33 REF_MON
AD9525
32
VDD3
6
7
8
9
10
11
12
OUT_RSET
31 SYNC_OUT
30 SYNC_OUT
29
GND
28 SDO
27 SDIO
TOP
VIEW
(Not to Scale)
CLKIN
CLKIN
VDD3
STATUS
REFC
REF_SEL
26
SCLK
25 CS
NOTES
1. THE EXPOSED PAD IS A GROUND CONNECTION ON THE CHIP THAT
MUST BE SOLDERED TO THE ANALOG GROUND OF THE PCB TO
ENSURE PROPER FUNCTIONALITY AND HEAT DISSIPATION, NOISE,
AND MECHANICAL STRENGTH BENEFITS.
Figure 4. Pin Configuration
Table 22. Pin Function Descriptions
Pin No. Mnemonic Type Description
1
2
3
4
5
6
7
8
OUT1
O
O
P
O
O
O
I
LVPECL Complementary Output 1.
OUT1
VDD3
OUT0
LVPECL Output 1.
3.3 V Power Supply for Channel OUT0 and Channel OUT1.
LVPECL Complementary Output 0.
OUT0
LVPECL Output 0.
OUT_RSET
CLKIN
CLKIN
Clock Distribution Current Set Resistor. Connect a 4.12 kΩ resistor from this pin to GND.
Along with CLKIN, this pin is the differential input for the clock distribution section.
I
Along with CLKIN, this pin is the differential input for the clock distribution section. If a single-ended input is
connected to the CLKIN pin, connect a 0.1 µF bypass capacitor from CLKIN to ground.
9
VDD3
STATUS
REFC
REF_SEL
VDD_CP
P
O
I
I
P
3.3 V Power Supply for CLK Inputs, M Divider, and Output Distribution.
Lock Detect and Other Status Signals.
Reference Clock Input C. This pin is a CMOS input for the PLL reference.
Reference Input Select. Logic high = REFB. No internal pull-up or pull-down resistor on this pin.
Power Supply for Charge Pump (CP). VDD3 < VDD_CP < 5.0 V. VDD_CP must still be connected to 3.3 V if the PLL
is not used.
10
11
12
13
14
CP
O
Charge Pump (Output). This pin connects to an external loop filter. This pin can be left unconnected if the
PLL is not used.
15
16
GND
CP_RSET
GND Ground for Charge Pump VDD_CP Supply. Connect to ground.
O
Charge Pump Current Set Resistor. Connect a 5.1 kΩ resistor from this pin to GND. This resistor can be
omitted if the PLL is not used.
17
18
19
20
21
22
23
24
25
26
27
REFA
REFA
GND
VDD3
REFB
REFB
PD
I
I
Reference Clock Input A. Along with REFA, this pin is the differential input for the PLL reference.
Reference Clock Input A. Along with REFA, this pin is the differential input for the PLL reference.
GND Ground for PLL Power Supply. Connect to ground.
P
I
3.3 V Power Supply for PLL.
Reference Clock Input B. Along with REFB, this pin is the differential input for the PLL reference.
Reference Clock Input B. Along with REFB, this pin is the differential input for the PLL reference.
Chip Power-Down, Active Low. This pin has an internal 30 kΩ pull-up resistor.
Chip Reset, Active Low. This pin has an internal 30 kΩ pull-up resistor.
Serial Control Port Chip Select; Active Low. This pin has an internal 30 kΩ pull-up resistor.
Serial Control Port Clock Signal. This pin has an internal 30 kΩ pull-down resistor.
Serial Control Port Bidirectional Serial Data In/Out.
I
I
RESET
CS
I
I
SCLK
SDIO
I
I
Rev. 0 | Page 13 of 48
AD9525
Data Sheet
Pin No. Mnemonic Type Description
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
EP
SDO
GND
I
Serial Control Port Unidirectional Serial Data Out.
GND Connect to ground.
SYNC_OUT
SYNC_OUT
VDD3
REF_MON
OUT7
O
O
P
O
O
O
P
O
O
O
O
P
O
O
O
O
P
LVPECL Complementary Output for Programmable Sync Signal.
LVPECL Output for Programmable Sync Signal.
Power Supply for SYNC_OUT Driver.
Reference Monitor (Output). This pin has multiple selectable outputs.
LVPECL Complementary Output 7.
LVPECL Output 7.
3.3 V Power Supply for Channel OUT6 and Channel OUT7.
LVPECL Complementary Output 6.
LVPECL Output 6.
LVPECL Complementary Output 5.
LVPECL Output 5.
3.3 V Power Supply for Channel OUT4 and Channel OUT5.
LVPECL Complementary Output 4.
LVPECL Output 4.
OUT7
VDD3
OUT6
OUT6
OUT5
OUT5
VDD3
OUT4
OUT4
OUT3
LVPECL Complementary Output 3.
LVPECL Output 3.
3.3 V Power Supply for Channel OUT2 and Channel OUT3.
LVPECL Complementary Output 2.
LVPECL Output 2.
OUT3
VDD3
OUT2
O
O
OUT2
EP, GND
GND Exposed Paddle. The exposed pad is a ground connection on the chip that must be soldered to the analog
ground of the PCB to ensure proper functionality and heat dissipation, noise, and mechanical strength
benefits.
Rev. 0 | Page 14 of 48
Data Sheet
AD9525
TYPICAL PERFORMANCE CHARACTERISTICS
6
5
PUMP UP
PUMP DOWN
4
1
3
2
1
0
CH1 500mV Ω
2.5ns/DIV
40.0GS/s
A CH1 40.0mV
0
1
2
3
4
VOLTAGE ON CP PIN (V)
Figure 5. Charge Pump Characteristics at VDD_CP = 3.3 V
Figure 8. LVPECL Output (Differential) at 122.88 MHz
6
5
4
3
2
1
0
2.5
2.3
2.1
1.9
1.7
1.5
1.3
1.1
0.9
0.7
0.5
960mV p-p
780mV p-p
PUMP UP
PUMP DOWN
600mV p-p
400mV p-p
0
500
1000
1500
2000
2500
3000
0
1
2
3
4
5
6
FREQUENCY (MHz)
VOLTAGE ON CP PIN (V)
Figure 6. Charge Pump Characteristics at VDD_CP = 5.0 V
Figure 9. LVPECL Differential Voltage Swing vs. Frequency
–217.5
–218.0
–218.5
–219.0
–219.5
–220.0
–220.5
–221.0
–221.5
–222.0
–222.5
0
0.2
0.4
0.6
0.8
1.0
1.2
SLEW RATE OF REFA (V/ns)
Figure 7. PLL Figure of Merit (FOM) vs. Slew Rate at REFA
Rev. 0 | Page 15 of 48
AD9525
Data Sheet
–20
–30
–80
1: 1kHz, –96.0dBc/Hz
2: 10kHz, –106.3dBc/Hz
3: 100kHz, –137.2dBc/Hz
4: 800kHz, –144.5dBc/Hz
5: 1MHz, –144.6dBc/Hz
6: 10MHz, –147.7dBc/Hz
7: 100MHz, –152.4dBc/Hz
–90
–40
–50
–100
–110
–120
–130
–140
–150
–160
–170
–60
–70
–80
–90
–100
–110
–120
–130
–140
–150
–160
–170
–180
1
2
3
5
NOISE:
ANALYSIS RANGE X: START 1kHz
STOP 100MHz
7
4
6
INTG NOISE: –59.5dBc/100MHz
RMS NOISE: 1.5mRAD
86.2mdeg
RMS JITTER: 81.2fsec
100
1k
10k
100k
1M
10M
100M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 10. Additive (Residual) Phase Noise, CLK-to-LVPECL at 122.88 MHz,
Divide-by-1
Figure 13. Phase Noise (Absolute), External VCO (Z-Communications Model
CRO-2950) at 2949.12 MHz; PFD = 122.88 MHz; LBW = 8 kHz;
LVPECL Output = 2949.12 MHz
–80
–90
–20
1: 1kHz, –109.3936dBc/Hz
–30
2: 10kHz, –113.5616dBc/Hz
3: 100kHz, –143.3042dBc/Hz
4: 800kHz, –150.5212dBc/Hz
–40
5: 1MHz, –150.7666dBc/Hz
–50
6: 10MHz, –152.9127dBc/Hz
7: 100MHz, –156.0506 dBc/Hz
–100
–110
–120
–130
–140
–150
–160
–170
–60
–70
–80
–90
–100
–110
–120
–130
–140
–150
–160
–170
–180
1
2
3
NOISE:
5
ANALYSIS RANGE X: START 1kHz
STOP 100MHz
7
4
6
INTG NOISE: –67.8dBc/100MHz
RMS NOISE: 575.9µRAD
33.0mdeg
RMS JITTER: 62.2fsec
10
100
1k
10k
100k
1M
10M
100M
100
1k
10k
100k
1M
10M
100M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 11. Additive (Residual) Phase Noise, CLK-to-LVPECL at 1500 MHz,
Divide-by-1
Figure 14. Phase Noise (Absolute), External VCO (Z-Communications Model
CRO-2950) at 2949.12 MHz; PFD = 122.88 MHz; LBW = 8k Hz;
LVPECL Output = 1474.56 MHz
–20
–20
1: 1kHz, –136.9dBc/Hz
1: 1kHz, –103.4dBc/Hz
–30
–30
2: 10kHz, –150.3dBc/Hz
2: 10kHz, –109.2dBc/Hz
3: 100kHz, –156.4dBc/Hz
–40
–40
–50
3: 100kHz, –130.6dBc/Hz
4: 800kHz, –147.3dBc/Hz
5: 1MHz, –148.5dBc/Hz
6: 10MHz, –152.9dBc/Hz
7: 100MHz, –154.4dBc/Hz
4: 800kHz, –161.1dBc/Hz
5: 1MHz, –160.9dBc/Hz
–50
6: 10MHz, –161.7dBc/Hz
7: 100MHz, –161.8dBc/Hz
–60
–60
NOISE:
–70
–70
ANALYSIS RANGE X: START 12kHz
–80
–90
STOP 20MHz
–80
INTG NOISE: –88.6dBc/20.0MHz
–90
RMS NOISE: 52.8µRAD
3.0mdeg
–100
–110
–120
–130
–140
–150
–160
–170
–180
–100
–110
–120
–130
–140
–150
–160
–170
–180
RMS JITTER: 68.4fsec
1
2
3
5
NOISE:
ANALYSIS RANGE X: START 1kHz
STOP 100MHz
1
7
5
7
4
2
6
INTG NOISE: –63.7dBc/100MHz
3
RMS NOISE: 919.9µRAD
52.7mdeg
4
6
RMS JITTER: 99.3fsec
100
1k
10k
100k
1M
10M
100
1k
10k
100k
1M
10M
100M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 12. Phase Noise (Absolute), External VCO
(Bowei Model MVCO-1475) at 1474.56 MHz; PFD = 122.88 MHz;
LBW = 18 kHz; LVPECL Output = 1474.56 MHz
Figure 15. Phase Noise (Absolute), External VCXO (122.88 MHz VCXO)
(Crystek CVHD-950); Reference = 122.88 MHz; R Divider = 1);
LBW = 40 Hz; LVPECL Output = 122.88 MHz
Rev. 0 | Page 16 of 48
Data Sheet
AD9525
–20
–30
–20
–30
1: 1kHz, –85.0dBc/Hz
2: 10kHz, –99.3dBc/Hz
3: 100kHz, –123.0dBc/Hz
4: 800kHz, –140.7dBc/Hz
5: 1MHz, –142.0dBc/Hz
6: 10MHz, –149.0dBc/Hz
7: 100MHz, –153.3dBc/Hz
–40
–40
–50
–50
–60
–60
–70
–70
–80
–80
–90
–90
1
1
–100
–110
–120
–130
–140
–150
–160
–170
–180
–100
–110
–120
–130
2
3
2
5
–140
NOISE:
5
7
7
4
3
ANALYSIS RANGE X: START 1kHz
–150
–160
–170
–180
STOP 100MHz
6
4
6
INTG NOISE: –62.1dBc/19.7MHz
RMS NOISE: 1.1µRAD
63.6mdeg
RMS JITTER: 86.2fsec
100
1k
10k
100k
1M
10M
100M
100
1k
10k
100k
1M
10M
100M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 16. Phase Noise (Absolute), External VCO 2.05 GHz VCO
(Bowei Model MVCO-2050A); at 2050 MHz; Reference = 122.054215 MHz;
R Divider = 12
Figure 17. Phase Noise (Absolute), External VCO (Z-Communications
CRO1474-LF) at 1474.56 MHz; PFD = 122.88 MHz;
LBW = 15 kHz; LVPECL Output = 1474.56 MHz
Rev. 0 | Page 17 of 48
AD9525
Data Sheet
TERMINOLOGY
Time Jitter
Phase Jitter and Phase Noise
Phase noise is a frequency domain phenomenon. In the time
domain, the same effect is exhibited as time jitter. When observing
a sine wave, the time of successive zero crossings varies. In a square
wave, the time jitter is a displacement of the edges from their
ideal (regular) times of occurrence. In both cases, the variations in
timing from the ideal are the time jitter. Because these variations
are random in nature, the time jitter is specified in seconds root
mean square (rms) or 1 sigma of the Gaussian distribution.
An ideal sine wave can be thought of as having a continuous
and even progression of phase with time from 0° to 360° for
each cycle. Actual signals, however, display a certain amount
of variation from ideal phase progression over time. This
phenomenon is called phase jitter. Although many causes can
contribute to phase jitter, one major cause is random noise,
which is characterized statistically as being Gaussian (normal)
in distribution.
Time jitter that occurs on a sampling clock for a DAC or an
ADC decreases the signal-to-noise ratio (SNR) and dynamic
range of the converter. A sampling clock with the lowest possible
jitter provides the highest performance from a given converter.
This phase jitter leads to a spreading out of the energy of the
sine wave in the frequency domain, producing a continuous
power spectrum. This power spectrum is usually reported as
a series of values whose units are dBc/Hz at a given offset in
frequency from the sine wave (carrier). The value is a ratio
(expressed in decibels) of the power contained within a 1 Hz
bandwidth with respect to the power at the carrier frequency.
For each measurement, the offset from the carrier frequency is
also given.
Additive Phase Noise
Additive phase noise is the amount of phase noise that can be
attributed to the device or subsystem being measured. The phase
noise of any external oscillators or clock sources is subtracted,
making it possible to predict the degree to which the device
impacts the total system phase noise when used in conjunction
with the various oscillators and clock sources, each of which
contributes its own phase noise to the total. In many cases, the
phase noise of one element dominates the system phase noise.
When there are multiple contributors to phase noise, the total is
the square root of the sum of squares of the individual contributors.
It is meaningful to integrate the total power contained within
some interval of offset frequencies (for example, 10 kHz to
10 MHz). This is called the integrated phase noise over that
frequency offset interval; it can be readily related to the time
jitter due to the phase noise within that offset frequency interval.
Phase noise has a detrimental effect on the performance of ADCs,
DACs, and RF mixers. It lowers the achievable dynamic range of
the converters and mixers, although they are affected in somewhat
different ways.
Additive Time Jitter
Additive time jitter is the amount of time jitter that can be attri-
buted to the device or subsystem being measured. The time jitter of
any external oscillators or clock sources is subtracted. This makes it
possible to predict the degree to which the device impacts the total
system time jitter when used in conjunction with the various
oscillators and clock sources, each of which contributes its own
time jitter to the total. In many cases, the time jitter of the external
oscillators and clock sources dominates the system time jitter.
Rev. 0 | Page 18 of 48
Data Sheet
AD9525
DETAILED BLOCK DIAGRAM
REF_SEL
CP
VDD_CP CP_RSET CLKIN CLKIN
AD9525
NINE
DIFFERENTIAL
OUTPUTS
LVPECL
REFA
REFA
÷R
A
1, 2, 3... 32
SYNC_OUT
SYNC_OUT
REFB
REFB
÷R
B
1, 2, 3... 32
SYNC
GENERATION
CHARGE
PUMP
÷S
PFD
OUT7
OUT7
÷R
C
÷M
1, 2, 3, 4, 5, 6
REFC
1, 2, 3... 127
OUT6
OUT6
OUT5
OUT5
SDIO
SDO
SCLK
CS
OUT4
OUT4
CONTROL
INTERFACE
(SPI)
OUT3
OUT3
÷N
RESET
PD
OUT2
OUT2
÷B
1, 2, 3... 32
OUT1
OUT1
÷P
STATUS
MONITOR
1, 2, 3, 4, 5, 6
STATUS
OUT0
OUT0
REF_MON
Figure 18. Detailed Block Diagram
Rev. 0 | Page 19 of 48
AD9525
Data Sheet
THEORY OF OPERATION
The AD9525 PLL is useful for generating clock frequencies from
a supplied reference frequency. In addition, the PLL can be used
to clean up jitter and phase noise on a noisy reference. The exact
choice of PLL parameters and loop dynamics is application specific.
The flexibility and depth of the AD9525 PLL allow the part to
be tailored to function in many different applications and signal
environments.
An important limit to keep in mind is the maximum frequency
allowed into the PFD. The maximum input frequency into the
PFD is a function of the antibacklash pulse setting, as specified
in the phase/frequency detector (PFD) parameter in Table 7.
Charge Pump (CP)
The charge pump is controlled by the PFD. The PFD monitors
the phase and frequency relationship between its two inputs and
tells the CP to pump up or pump down to charge or discharge the
integrating node (part of the loop filter). The integrated and
filtered CP current is transformed into a voltage that drives the
tuning node of the external VCO to move the VCO frequency
up or down. The CP can be set for high impedance (allows
holdover operation), for normal operation (attempts to lock the
PLL loop), for pump-up, or for pump-down (test modes). The CP
current is programmable in eight steps. The exact value of the CP
current LSB is set by the CPRSET resistor, which is nominally
5.1 kΩ. The actual LSB current can be calculated by CP_LSB =
3.06/CPRSET.
The AD9525 includes on-chip PLL blocks that can be used with
an external VCO or VCXO to create a complete phase-locked
loop. The PLL requires an external loop filter, which usually
consists of a small number of capacitors and resistors. The
configuration and components of the loop filter help to establish
the loop bandwidth and stability of the PLL. The external loop
filter that must be connected between CP and the tuning pin of
the VCO/VCXO. This loop filter determines the loop bandwidth
and stability of the PLL. Make sure to select the proper PFD
polarity for the VCO/VCXO being used.
The AD9525 can also be configured as a clock distribution by
CLKIN
shutting down the PLL and using CLKIN and
as the
PLL External Loop Filter
input. The M divider can be used to divide the input frequency
down to the desired output frequency to each of the eight LVPECL
outputs.
An example of an external loop filter for the PLL is shown in
Figure 19. A loop filter must be calculated for each desired PLL
configuration. The values of the components depend on the VCO
frequency, the KVCO, the PFD frequency, the charge pump
current, the desired loop bandwidth, and the desired phase
margin. The loop filter affects the phase noise, the loop settling
time, and the loop stability. A basic knowledge of PLL theory is
necessary for understanding loop filter design. ADIsimCLK can
help with the calculation of a loop filter according to the application
requirements.
CONFIGURATION OF THE PLL
Configuration of the PLL is accomplished by programming
the various settings for the R divider, N divider, PFD polarity,
and charge pump current. The combination of these settings
and the loop filter determines the PLL loop bandwidth and PLL
stability. These are managed through programmable register
settings and by the design of the external loop filter.
PLL Reference Inputs
Successful PLL operation and satisfactory PLL loop performance
are highly dependent on proper configuration of the PLL settings,
and the design of the external loop filter is crucial to the proper
operation of the PLL.
The AD9525 features two fully differential PLL reference input
circuits. The differential inputs are self-biased, allowing for easy
ac coupling of input signals. All PLL reference inputs are off by
default. The self-bias level of the two sides is offset slightly to
prevent chattering of the input buffer when the reference is ac
coupled and is slow or missing. The input offset increases the
voltage swing required of the driver to overcome the offset. The
input frequency range and common-mode voltages for the
reference inputs are specified in Table 4.
ADIsimCLK™ is a free program that can help with the design
and exploration of the capabilities and features of the AD9525,
including the design of the PLL loop filter. The AD9516 model
found in the latest ADIsimCLK version can be used for modeling
the AD9525 loop filter. It is available at www.analog.com/clocks.
Phase Frequency Detector (PFD)
The reference input receiver is powered down when the PLL is
powered down. It is possible to dc couple to these inputs. If the
differential reference input is driven by a single-ended signal,
The PFD takes inputs from the R divider and the N divider and
produces an output proportional to the phase and frequency
difference between them. The PFD includes a programmable
delay element that controls the width of the antibacklash pulse.
This pulse ensures that there is no dead zone in the PFD transfer
function and minimizes phase noise and reference spurs. The
antibacklash pulse width is set by Register 0x010[1:0].
REFA REFB
the unused side (
or
) should be decoupled via a
suitable capacitor to a quiet ground.
The AD9525 provides a third single-ended CMOS reference
input referred to as REFC.
Rev. 0 | Page 20 of 48
Data Sheet
AD9525
Reference Switchover
M Divider
The AD9525 supports two separate differential reference inputs.
Manual switchover is performed between these inputs either
through Register 0x01A or by using the REF_SEL pin. This
feature supports networking and other applications that require
redundant references.
The M divider is a fixed divide (FD) of 1, 2, 3, 4, 5, or 6.
The maximum input frequency to the M counter is reflected in
the maximum CLKIN input frequency specified in Table 6.
The M divider provides frequency division between the CLKIN
input and the N feedback divider and clock distribution output
channels.
Manual switchover requires that a clock be present on the reference
input that is being switched to or that the switchover deglitching
feature be disabled (Register 0x01A[4]).
The M divider can also be set to static, which is useful for
applications where the only desired output frequency is the
CLK input frequency.
Reference Dividers R
The reference inputs are routed to their respective divider, R. R can
be set to any value from 1 to 32 (Both R = 0 and R = 1 give divide-
by-1.).
P Divider
The P divider is a fixed divide (FD) of 1, 2, 3, 4, 5 or 6.
The maximum input frequency to the P counter is reflected in
the maximum CLKIN input frequency specified in Table 4.
The division is set by the values of RLOW and RHIGH. The divider
can be bypassed (equivalent to divide-by-1, divider circuit is
powered down) by setting the bypass bit.
B Divider
For each R divider, the frequency division (RX) is set by the values
of RLOW and RHIGH (four bits each, representing Decimal 0 to
Decimal 15), where
The B divider is a fixed divide (FD) of 1, 2, 3, …or 32.
The maximum input frequency to the B counter is ~1500 MHz,
as specified in Table 7. This is the prescaler input frequency
(external VCO or CLKIN) divided by the P and M counters.
For example, M = 1 and P = 1 mode is not allowed if the
external VCO frequency is greater than 1500 MHz because the
frequency going to the B divider is too high.
Number of Low Cycles = RLOW + 1
Number of High Cycles = RHIGH + 1
The high and low cycles are cycles of the clock signal currently
routed to the input of the R.
The division is set by the values of BLOW and BHIGH. The divider
can be bypassed (equivalent to divide-by-1, divider circuit is
powered down) by setting the bypass bit.
When a divider is bypassed, RX = 1.
Otherwise, RX = (RHIGH + 1) + (RLOW + 1) = RHIGH + RLOW + 2.
This allows each reference divider to divide by any integer from
1 to 32.
The frequency division, BX, is set by the values of BLOW and
BHIGH (four bits each, representing Decimal 0 to Decimal 15),
where
The output of the R divider goes to a mux to select one of the
references to the PFD inputs. The frequency applied to the PFD
must not exceed the maximum allowable frequency, which
depends on the antibacklash pulse setting (see Table 7).
Number of Low Cycles = BLOW + 1
Number of High Cycles = BHIGH + 1
The high and low cycles are cycles of the clock signal currently
routed to the input of the B divider.
The R divider has its own reset. The R divider can also be reset
using the shared reset bit of the R and B counters. This reset bit
is not self-clearing.
When a divider is bypassed, BX = 1.
The R divider in the REFC path has a division ratio programmable
from 1 to 127.
Otherwise, BX = (BHIGH + 1) + (BLOW + 1) = BHIGH + BLOW + 2.
Although manual reset is not normally required, the B counter has
its own reset bit. Note that this reset bit is not self-clearing.
VCO/VCXO, M and N Feedback Dividers
The feedback division is the product of the M divider and the
N divider. The N divider is a combination of a prescaler (P) and
a B divider.
f
VCO = (fREF/R) × N × M
where:
M =1, 2, 3, 4, 5, or 6.
N = (P × B).
P =1, 2, 3, 4, 5, or 6.
B = 1, 2, 3, … or 32.
Rev. 0 | Page 21 of 48
AD9525
Data Sheet
Digital Lock Detect (DLD)
VCO
1
ATTENUATOR
CLKIN
CLKIN
V
TUNE
By selecting the proper output through the mux on each pin, the
DLD function is available at the STATUS and REF_MON pins.
The digital lock detect circuit indicates a lock when the time
difference of the rising edges at the PFD inputs is less than a
specified value (the lock threshold). The loss of a lock is indicated
when the time difference exceeds a specified value (the unlock
threshold). Note that the unlock threshold is wider than the
lock threshold, which allows some phase error in excess of the
lock window to occur without chattering on the lock indicator.
50Ω
R2
CP
R1
C3
C2
C1
AD9525
The lock detect window timing depends on the value of the
CPRSET resistor, as well as three settings: the digital lock detect
window bit (Register 0x019[1]), the antibacklash pulse width
bits (Register 0x010[1:0], see Table 8), and the lock detect counter
bits (Register 0x019[3:2]). The lock and unlock detection values in
Table 8 are for the nominal value of CPRSET = 5.11 kΩ. Doubling
the CPRSET value to 10 kΩ doubles the values in Table 8.
1
VCO MANUFACTURERS RECOMMEND EITHER A T OR PI ATTENUATOR
TO PREVENT VCO PULLING. REFER TO MANUFACTURER’S
RECOMMENDATION
Figure 19. CLKIN Configured as Single-Ended VCO
CMOS VCXO
100kΩ
CLKIN
V
TUNE
A lock is not indicated until there is a programmable number
of consecutive PFD cycles with a time difference that is less than
the lock detect threshold. The lock detect circuit continues to
indicate a lock until a time difference greater than the unlock
threshold occurs on a single subsequent cycle. For the lock detect
to work properly, the period of the PFD frequency must be
greater than the unlock threshold. The number of consecutive PFD
cycles required for a lock is programmable (Register 0x018[6:5]).
100kΩ
CLKIN
CP
R2
R
1
C3
C2
C1
AD9525
Note that, in certain low (<500 Hz) loop bandwidth, high phase
margin cases, it is possible that the DLD can chatter during
acquisition. This is normal and occurs because the PFD inputs
are moving slowly in and out of the lock/unlock window during
PLL loop settling. Adjustment of the lock detect counter setting
(Register 0x019[3:2]) can suppress this behavior.
Figure 20. CLKIN Configured as Single-Ended CMOS VCXO
1
PECL VCXO
CLKIN
V
CLKIN
TUNE
External VCXO/VCO Clock Input (CLKIN/
)
CLKIN
This differential input is used to drive the AD9525 clock
distribution section. The pins are internally self-biased, and the
input signal should be ac-coupled via capacitors.
R2
CP
CLKIN
The CLKIN/
input can be used either as a distribution
R1
only input (with the PLL off) or as a feedback input for an external
VCO/VCXO using the internal PLL. Sample configurations
are illustrated in Figure 19 through Figure 21. Refer to the
manufacturer’s recommendation for VCO terminations; a T or
PI attenuator is often recommended, as illustrated in Figure 19.
C3
C2
C1
AD9525
1
PROVIDE THE PROPER VCXO
MANUFACTURER PECL TERMINATION.
For operation using a CMOS input, an external resistive divider
is required to limit the swing on CLKIN (see Table 6 for the
maximum input rating).
Figure 21. CLKIN Configured as Differential LVPECL VCXO
Status Monitor
The AD9525 contains three frequency status monitors that are
used to indicate if the PLL reference (or references, in the case
of single-ended mode) and the VCO have fallen below a threshold.
Rev. 0 | Page 22 of 48
Data Sheet
AD9525
ways to activate safe power-down mode: individually set the
power-down bit for each driver, power down an individual
output channel, or activate sleep mode.
CLOCK DISTRIBUTION
The AD9525 can be used only as a clock fan out buffer by
disabling the PLL circuit blocks except for the clock distribution
section. The clock distribution consists of eight LVPECL clock
output drivers that share a common M divider. See the M Divider
section for more information on the common M divider.
In total power-down mode 0x0230[1] = 1 (power down
distribution reference). This mode must not be used if there is
an external voltage bias network (such as Thevenin equivalent
termination) on the output pins that will cause a dc voltage to
appear at the powered down outputs. However, total power-down
mode is allowed when the LVPECL drivers are terminated using
only pull-down resistors.
Duty Cycle and Duty-Cycle Correction
The duty cycle of the clock signal at the output of a driver is
a result of either or both of the following conditions:
CLKIN CLKIN
input duty cycle. If the CLKIN,
•
The CLKIN,
input is routed directly to the output, the duty cycle of the
CLKIN
SW1B SW1A
output is the same as the CLKIN,
input.
•
The M divider value. An odd M divider value results in
a non-50% duty cycle.
R2
200Ω
R1
200Ω
N1
QN1
OUT
OUT
N2
Table 23.Typical Output Duty Cycle with M Divider ≠ 1
QN2
M Divider
Output Duty Cycle (%)
Even
50
Odd = 3
Odd = 5
33.3
40
SW2
4.4mA
LVPECL Output Drivers
Figure 22. LVPECL Output Simplified Equivalent Circuit
The LVPECL differential voltage (VOD) is selectable (from
~400 mV to 960 mV (see Bit 2 and Bit 1 in Register 0x0F0 to
Register 0x0F7).
SYNC_OUT
SYNC_OUT provides one LVPECL output or two CMOS
output signal that can used to reset or synchronize a converter.
SYNC_OUT functionality block diagram is shown in Figure 23.
The SYNC_OUT signal is derived from the PLL phase detector
reference input clock or feedback (N-divider) clock. A program-
mable 16-bit S divider further divides the selected reference clock.
There are three different modes of operation for SYNC_OUT:
single shot, periodic, or pseudorandom. SYNC_OUT is retimed to
the high speed clock.
The LVPECL output polarity can be set as noninverting or
inverting, which allows for the adjustment of the relative
polarity of outputs within an application without requiring
a board layout change. Each LVPECL output can be powered
down or powered up, as needed. Because of the architecture of
the LVPECL output stages, there is the possibility of electrical
overstress and breakdown under certain power-down conditions.
For this reason, the LVPECL outputs have two power-down modes:
total power-down and safe power-down. The primary power-
down mode is the safe power-down mode. This mode continues
to protect the output devices while powered down. There are three
OUT0 TO OUT7
UP
REF
PFD
CP
÷M
DN
LOW
÷N
11 10 00 01
SELECT REF: REF, FB, PD
DIGITAL LOCK DETECT
SYNC ENABLE
SYNC_OUT
÷S DIGITAL SYNC CONTROL
M DIVIDER OUTPUT
D
SET
CLR
Q
Q
Figure 23. SYNC_OUT Functional Diagram
Rev. 0 | Page 23 of 48
AD9525
Data Sheet
Single Shot Mode
Pseudorandom Mode
In single shot mode one sync pulse occurs after writing SYNC
ENABLE 0x192[4] = 1. An IO_UPDATE is required to complete
a register write. The width of the sync pulse is determined by the
value of the S divider. A divider value of 0x0000 allows a pulse
whose width is equal to one half period of the phase detector rate.
A divider value of 0x0001 allows a pulse whose width is equal
to two half periods of the phase detector rate. In single shot
mode, the sync enable bit is self-clearing and the sync circuits
are ready to receive another sync enable.
Pseudorandom mode is similar to periodic mode but the pulse
is a PN17 sequence that is continuous until SYNC ENABLE is
cleared by a register writing SYNC ENABLE 0x192[4] = 0. An
IO_UPDATE is required to complete a register write. The width
of the sync pulse is equal to one half period the phase detector
rate. The pulse repetition rate is determined by the value of the
S divider. A divider value of 0x0000 allows a pulse rate equal to
the phase detector rate. A divider value of 0x0001 allows pulse
rate equal to two half the phase detector rate.
Periodic Mode
SYNC_OUT Programming
In periodic mode, the pulse is continuous until SYNC ENABLE
is cleared by a register writing SYNC ENABLE 0x192[4] = 0.
An IO_UPDATE is required to complete a register write. The
width of the sync pulse is equal to one half period of the phase
detector rate. The pulse repetition rate is determined by the
value of the S divider. A divider value of 0x0000 allows a pulse
rate equal to the phase detector rate. A divider value of 0x0001
allows a pulse rate equal to two half periods of the phase detector
rate. The SYNC_OUT signal is resampled with the OUT clock
to ensure time alignment and minimum output skew. There is a
possibility in periodic mode that the SYNC_OUT could slip one
half cycle of the OUT clock period.
The procedure to configure the SYNC_OUT depends on the
logic requirement of the converters that require synchroniza-
tion. Analog Devices, Inc., converters are synchronized on the
rise edge of the SYNC pulse.
SYNC_OUT CMOS Driver
The user can also configure the LVPECL SYNC_OUT as a pair
of CMOS outputs. When the output is configured as CMOS,
CMOS Output A and CMOS Output B are automatically turned
on. Either CMOS Output A or Output B can be turned on or off
independently. The user can also select the relative polarity of the
CMOS outputs for any combination of inverting and noninverting
(see Register 0x0F9). The user can power down each CMOS output
as needed to save power. The CMOS driver is in tristate when it is
powered down.
S DIVIDER = 0
tSTART
REF CLOCK
SYNC ENABLE = HIGH
(SINGLE SHOT SELF CLEARING)
IO_UPDATE
SYNC_OUT
MODE = SINGLE SHOT
SYNC_OUT
MODE = PERIODIC
SYNC_OUT
MODE = PN17
SYNC ENABLE = LOW
(SINGLE SHOT SELF CLEARING)
IO_UPDATE
tSTOP
Figure 24. SYNC Output Timing
Rev. 0 | Page 24 of 48
Data Sheet
AD9525
SYNC_OUT
CONTROL
USER PROGRAMS
REGISTER VALUE
FOR S DIVIDER
PROGRAM: S DIVIDER,
SYNC MODE
AND SYNC MODE
PROGRAM: SYNC
ENABLE
REQUEST SYNC
PROGRAM: IO UPDATE
DIGITAL LOCK DETECT
IS USED TO PREVENT
OCCURENCE OF SYNC
IF PLL IS UNLOCKED
NO
LOCK
DETECT = HIGH
YES
THE ANALOG CLOCK
TO THE DIGITAL STATE
MACHINE IS
DISABLED IF SYNC
IS DISABLED
ENABLE_ANALOG
SYNC HIGH FOR S DIVIDER + 1
REF CLOCK CYCLES
SYNC LOW
SYNC ENABLE IS SELF
CLEARING IN SINGLE
SHOT MODE. OTHER
MODES REQUIRE A
SPI WRITE TO DISABLE
SYNC_OUT
NO
SYNC ENABLE
LOW?
YES
END SYNC
PROCESS
Figure 25. SYNC_OUT Flowchart
RESET
Hardware Reset via the
Pin
RESET MODES
RESET
briefly pulling
The AD9525 has a power-on reset (POR) and several other
ways to apply a reset condition to the chip.
, a hard reset (an asynchronous hard reset is executed by
RESET
low), restores the chip to the on-chip
default register settings. It takes ~2 µs for the outputs to begin
RESET
Power-On Reset
toggling after
is issued.
During chip power-up, a power-on reset pulse is issued when
VDD reaches ~2.6 V (<2.8 V) and restores the chip to the
default on-chip setting. It takes ~70 ms for the outputs to begin
toggling after the power-on reset pulse signal is internally
generated. The default power-on state of the AD9525 is
configured as a buffer.
Soft Reset via the Serial Port
The serial port control register allows for a soft reset by setting
Bit 2 and Bit 5 in Register 0x000. When Bit 5 and Bit 2 are set,
the chip enters a soft reset mode and restores the chip to the on-
chip setting, except for Register 0x000. Except for the self-clearing
bits, Bit 2 and Bit 5, Register 0x000 retains its previous value
prior to reset. These bits are self-clearing. However, the self-clearing
operation does not complete until an additional serial port SCLK
cycle occurs, and the AD9525 is held in reset until that happens.
Rev. 0 | Page 25 of 48
AD9525
Data Sheet
PLL Power-Down
POWER-DOWN MODES
The PLL section of the AD9525 can be selectively powered down.
In this mode, the AD9525 can be used as a 1 to 8 clock buffer by
using the CLKIN as the clock input.
PD
Chip Power-Down via
The AD9525 can be put into a power-down condition by pulling
PD
the
currents inside the AD9525. The chip remains in this power-down
PD
pin low. Power-down turns off most of the functions and
Distribution Power-Down
state until
is brought back to logic high. When taken out of
The distribution section can be powered down by writing
Register 0x230[4] = 1b, which turns off the bias to the distribution
section.
power-down mode, the AD9525 returns to the settings that
were programmed into its registers prior to the power-down,
unless the registers are changed by new programming while
Individual Clock Output Power-Down
PD
the
pin is held low.
Any of the clock distribution outputs can be powered down
into safe power-down mode by individually writing to the
appropriate registers. The register map details the individual
power-down settings for each output. These settings are found
in Register 0x0F0[0] to Register 0x0F7[0].
Powering down the chip shuts down the currents on the chip,
except for the bias current necessary to maintain the LVPECL
outputs in a safe shutdown mode. The LVPECL bias currents are
needed to protect the LVPECL output circuitry from damage that
can be caused by certain termination and load configurations
when tristated. Because this is not a complete power-down, it
can be called sleep mode.
Individual Clock Channel Power-Down
Any of the clock distribution channels can be powered down
individually by writing to the appropriate registers. Powering
down a clock channel is similar to powering down an individual
driver, but it saves more power because additional circuits are also
powered down. Powering down a clock channel also automatically
powers down the drivers connected to it. The register map details
the individual power-down settings for each output channel.
These settings are found in Register 0x0F0[4], Register 0x0F2[4],
Register 0x0F4[4], and Register 0x0F6[4].
PD
When the AD9525 is in a
following state:
power-down, the chip is in the
•
•
The PLL is off.
The CLKIN input buffer is off, but the CLKIN input dc
bias circuit is on.
The reference input buffer is off, but the dc bias circuit is
still on.
•
•
•
•
All dividers are off.
All LVPECL outputs are in safe off mode.
The serial control port is active, and the chip responds to
commands.
Rev. 0 | Page 26 of 48
Data Sheet
AD9525
SERIAL CONTROL PORT
The AD9525 serial control port is a flexible, synchronous serial
communications port that allows an easy interface with many
industry-standard microcontrollers and microprocessors. The
AD9525 serial control port is compatible with most synchronous
transfer formats, including Motorola® SPI and Intel® SSR protocols.
The serial control port allows read/write access to all registers
that configure the AD9525.
During this period, the serial control port state machine enters
a wait state until all data is sent. If the system controller decides
to abort the transfer before all of the data is sent, the state machine
must be reset, either by completing the remaining transfers or
CS
by returning
low for at least one complete SCLK cycle (but
CS
fewer than eight SCLK cycles). Raising the
pin on a nonbyte
boundary terminates the serial transfer and flushes the buffer.
PIN DESCRIPTIONS
In the streaming mode (see Table 25), any number of data bytes
can be transferred in a continuous stream. The register address
is automatically incremented or decremented (see the MSB/LSB
SCLK (serial clock) is the serial shift clock. This pin is an input.
SCLK is used to synchronize serial control port reads and writes.
Write data bits are registered on the rising edge of this clock,
and read data bits are registered on the falling edge. This pin is
internally pulled down by a 30 kΩ resistor to ground.
CS
First Transfers section).
must be raised at the end of the last
byte to be transferred, thereby ending streaming mode.
Communication Cycle—Instruction Plus Data
SDIO (serial data input/output) is a dual-purpose pin that acts
either as an input only (unidirectional mode) or as an input/
output (bidirectional mode). The AD9525 defaults to the
bidirectional I/O mode (Register 0x000[7] = 0b).
There are two parts to a communication cycle with the AD9525.
The first part writes a 16-bit instruction word into the AD9525,
coincident with the first 16 SCLK rising edges. The instruction
word provides the AD9525 serial control port with information
regarding the data transfer, which is the second part of the
communication cycle. The instruction word defines whether
the upcoming data transfer is a read or a write, the number of
bytes in the data transfer, and the starting register address for
the first byte of the data transfer.
SDO (serial data out) is used only in the unidirectional I/O mode
(Register 0x000[7] = 1b) as a separate output pin for reading back
data.
CS
(chip select bar) is an active low control that gates the read
CS
and write cycles. When
is high, SDO and SDIO are in a high
Write
impedance state. This pin is internally pulled up by a 30 kΩ
resistor to VS.
If the instruction word is for a write operation, the second part
is the transfer of data into the serial control port buffer of the
AD9525. Data bits are registered on the rising edge of SCLK.
AD9525
SERIAL PORT
CONTROL
(SPI)
SDIO
SDO
SCLK
CS
The length of the transfer (one, two, or three bytes or streaming
mode) is indicated by two bits ([W1:W0]) in the instruction
byte. When the transfer is one, two, or three bytes but not
Figure 26. Serial Control Port
CS
streaming,
stall the bus (except after the last byte, where it ends the cycle).
CS
can be raised after each sequence of eight bits to
GENERAL OPERATION OF SERIAL CONTROL PORT
Single byte or multiple byte transfers are supported, as well as
MSB first or LSB first transfer formats. The AD9525 serial control
port can be configured for a single bidirectional I/O pin (SDIO
only) or for two unidirectional I/O pins (SDIO/SDO). By default,
the AD9525 is in bidirectional mode. Short instruction mode
(8-bit instruction) is not supported. Only long instruction mode
(16-bit instruction) is supported.
When the bus is stalled, the serial transfer resumes when
lowered. Raising the
serial control port. During a write, streaming mode does not
skip over reserved or blank registers, and the user can write
0x00 to the reserved register addresses.
is
pin on a nonbyte boundary resets the
CS
Because data is written into a serial control port buffer area,
not directly into the actual control registers of the AD9525, an
additional operation is needed to transfer the serial control port
buffer contents to the actual control registers of the AD9525,
thereby causing them to become active. The update registers
operation (IO_UPDATE) consists of setting Register 0x232[0] =
1b (this bit is self-clearing). Any number of bytes of data can be
changed before executing an update registers. The update registers
operation simultaneously actuates all register changes that have
been written to the buffer since any previous update.
A write or a read operation to the AD9525 is initiated by
CS
pulling
low.
CS
The
stalled high mode is supported in data transfers where
three or fewer bytes of data (plus instruction data) are transferred
CS
(see Table 24). In this mode, the
pin can temporarily return
high on any byte boundary, allowing time for the system controller
CS
to process the next byte.
can go high on byte boundaries only
and can go high during either part (instruction or data) of the
transfer.
Rev. 0 | Page 27 of 48
AD9525
Data Sheet
Read
the range of the 0x232 registers used by the AD9525.
Bits[A12:A10] must always be 0b. For multibyte transfers, this
address is the starting byte address. In MSB first mode, subsequent
bytes decrement the address.
The AD9525 supports only the long instruction mode. If the
instruction word is for a read operation, the next N × 8 SCLK
cycles clock out the data from the address specified in the
instruction word, where N is 1 to 3 as determined by [W1:W0].
If N = 4, the read operation is in streaming mode, continuing
MSB/LSB FIRST TRANSFERS
The AD9525 instruction word and byte data can be MSB first
or LSB first. Any data written to Register 0x000 must be mirrored;
the upper four bits (Bits[7:4]) must mirror the lower four bits
(Bits[3:0]). This makes it irrelevant whether LSB first or MSB
first is in effect. As an example of this mirroring, see the default
setting for Register 0x000, which mirrors Bit 4 and Bit 3. This
sets the long instruction mode, which is the default and the only
mode that is supported.
CS
until
is raised. Streaming mode does not skip over reserved
or blank registers. The readback data is valid on the falling edge
of SCLK.
The default mode of the AD9525 serial control port is the
bidirectional mode. In bidirectional mode, both the sent data
and the readback data appear on the SDIO pin. It is also possible to
set the AD9525 to unidirectional mode (Register 0x000[7] = 1
and Register 0x000[0] = 1). In unidirectional mode, the readback
data appears on the SDO pin.
The default for the AD9525 is MSB first.
When LSB first is set by Register 0x000[1] and Register 0x000[6],
it takes effect immediately because it affects only the operation
of the serial control port and does not require that an update be
executed.
A readback request reads the data that is in the serial control
port buffer area or the data that is in the active registers
(see Figure 27). Readback of the buffer or active registers
is controlled by Register 0x004[0].
When MSB first mode is active, the instruction and data bytes
must be written from MSB to LSB. Multibyte data transfers in
MSB first format start with an instruction byte that includes the
register address of the most significant data byte. Subsequent
data bytes must follow, in order, from the high address to the
low address. In MSB first mode, the serial control port internal
address generator decrements for each data byte of the multibyte
transfer cycle.
The AD9525 uses Register Address 0x000 to Register
Address 0x232.
CS
SCLK/SCL
SDIO/SDA
UPDATE
REGISTERS
SERIAL
CONTROL
PORT
SDO
When LSB first is active, the instruction and data bytes must be
written from LSB to MSB. Multibyte data transfers in LSB first
format start with an instruction byte that includes the register
address of the least significant data byte, followed by multiple
data bytes. In a multibyte transfer cycle, the internal byte address
generator of the serial port increments for each byte.
WRITE REGISTER 0x232 = 0x001
TO UPDATE REGISTERS
Figure 27. Relationship Between Serial Control Port Buffer Registers and
Active Registers
THE INSTRUCTION WORD (16 BITS)
W
The MSB of the instruction word is R/ , which indicates
The AD9525 serial control port register address decrements
from the register address just written toward Register 0x000 for
multibyte I/O operations if the MSB first mode is active (default).
If the LSB first mode is active, the register address of the serial
control port increments from the address just written toward
Register 0x232 for multibyte I/O operations.
whether the instruction is a read or a write. The next two bits
([W1:W0]) indicate the length of the transfer in bytes. The final
13 bits are the address ([A12:A0]) at which to begin the read or
write operation.
For a write, the instruction word is followed by the number of
bytes of data indicated by Bits[W1:W0] (see Table 24).
Streaming mode always terminates when it reaches Register 0x232.
Note that unused addresses are not skipped during multibyte I/O
operations.
Table 24. Byte Transfer Count
W1
W0
Bytes to Transfer
0
0
1
1
0
1
0
1
1
2
3
Table 25. Streaming Mode (No Addresses Are Skipped)
Write Mode Address Direction Stop Sequence
LSB first
MSB first
Increment
Decrement
0x230, 0x231, 0x232, stop
0x001, 0x000, 0x232, stop
Streaming mode
Bits[A12:A0] select the address within the register map that is
written to or read from during the data transfer portion of the
communications cycle. Only Bits[A9:A0] are needed to cover
Rev. 0 | Page 28 of 48
Data Sheet
AD9525
Table 26. Serial Control Port, 16-Bit Instruction Word, MSB First
MSB
LSB
I15
I14
I13
I12
I11
I10
I9
I8
I7
I6
I5
I4
I3
I2
I1
I0
R/W
W1
W0
A12 = 0
A11 = 0
A10 = 0
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
CS
SCLK DON'T CARE
DON'T CARE
DON'T CARE
DON'T CARE
SDIO
R/W W1 W0 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0
16-BIT INSTRUCTION HEADER REGISTER (N) DATA REGISTER (N – 1) DATA
Figure 28. Serial Control Port Write—MSB First, 16-Bit Instruction, Two Bytes of Data
CS
SCLK
DON'T CARE
R/W W1 W0 A12 A11A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
DON'T CARE
SDIO
D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0
SDO DON'T CARE
16-BIT INSTRUCTION HEADER
REGISTER (N) DATA
REGISTER (N – 1) DATA
REGISTER (N – 2) DATA
REGISTER (N – 3) DATA
DON'T
CARE
Figure 29. Serial Control Port Read—MSB First, 16-Bit Instruction, Four Bytes of Data
tHIGH
tDS
tS
tC
tCLK
tDH
tLOW
CS
DON'T CARE
DON'T CARE
DON'T CARE
SCLK
SDIO
R/W
W1
W0
A12
A11
A10
A9
A8
A7
A6
A5
D4
D3
D2
D1
D0
DON'T CARE
Figure 30. Serial Control Port Write—MSB First, 16-Bit Instruction, Timing Measurements
CS
SCLK
tDV
SDIO
SDO
DATA BIT N
DATA BIT N – 1
Figure 31. Timing Diagram for Serial Control Port Register Read
CS
SCLK DON'T CARE
DON'T CARE
DON'T CARE
DON'T CARE
A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 W0 W1 R/W D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7
16-BIT INSTRUCTION HEADER REGISTER (N) DATA REGISTER (N + 1) DATA
SDIO
Figure 32. Serial Control Port Write—LSB First, 16-Bit Instruction, Two Bytes of Data
Rev. 0 | Page 29 of 48
AD9525
Data Sheet
tS
tC
CS
tCLK
tHIGH
tLOW
tDS
SCLK
SDIO
tDH
BIT N
BIT N + 1
Figure 33. Serial Control Port Timing—Write
Table 27. Serial Control Port Timing
Parameter
Description
tDS
tDH
tCLK
tS
Setup time between data and rising edge of SCLK
Hold time between data and rising edge of SCLK
Period of the clock
Setup time between the CS falling edge and SCLK rising edge (start of communication cycle)
Setup time between SCLK rising edge and the CS rising edge (end of communication cycle)
Minimum period that SCLK should be in a logic high state
tC
tHIGH
tLOW
tDV
Minimum period that SCLK should be in a logic low state
SCLK to valid SDIO and SDO (see Figure 31)
Rev. 0 | Page 30 of 48
Data Sheet
AD9525
CONTROL REGISTERS
CONTROL REGISTER MAP OVERVIEW
Register addresses that are not listed in Table 28 are not used,
and writing to those registers has no effect. Registers that are
marked as reserved should never have their values changed.
When writing to registers with bits that are marked reserved,
the user should take care to always write the default value for
the reserved bits.
Table 28. Control Register Map
Reg.
Default
Addr.
(Hex)
Register
Name
(MSB)
Bit 7
(LSB)
Bit 0
Value
(Hex)
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Serial Port Configuration
0x000 SPI mode
serial port
SD0
active
LSB first/
address
increase
Soft reset
Don't care
Don't care
Soft
reset
LSB first/
address
increase
SD0 active
Don't care
0x00
configuration
Don't
care
Don't care
Soft reset
Don't care
Don't care
Don't care
Don't care
Don't care
Soft
reset
Don't care
0x00
0x00
0x004 Readback
control
Don't
care
Don't care
Don't
care
Don't care
Read back
active regs
PLL Configuration
0x010 PFD charge
pump
PFD
polarity
CP current, Bits[2:0]
CP mode, Bits[1:0]
Antibacklash pulse width,
Bits[1:0]
0x7D
0x011 R dividers
0x012
REFB divider output high cycles, Bits[3:0]
REFB divider output low cycles, Bits[3:0]
REFA divider output low cycles, Bits[3:0]
B divider output low cycles, Bits[3:0]
P divider prescaler, Bits[2:0]
0x00
0x00
0x00
0x00
REFA divider output high cycles, Bits[3:0]
B divider output high cycles, Bits[3:0]
0x013 B divider
0x014 N divider
Don't
care
Don't care
B divider bypass REFB
divider
REFA divider
bypass
bypass
0x015 Resets
Don't
care
Reserved
Reserved
Reserved
B divider reset
REFB
divider
reset
REFA
divider reset
Reset all
dividers
0x00
0x016 REFC
REFC
enable
REFC divider, Bits[6:0]
0x00
0x00
0x017 Status pin
Charge
pump
STATUS pin
divider enable
STATUS output select, Bits[5:0]
pin to
VDD_CP/2
0x018 REF_MON pin
control
Don’t
care
Don’t care
Don't care
Don’t care
Don't care
REF_MON pin control, Bits[4:0]
0x00
0x00
0x00
0x019 Lock detect
Don't
care
Don’t care
Disable
Lock detect counter, Bits[1:0] Digital lock
detect window
Digital lock
det disable
0x01A
Ref
Enable
Enable REFB
present
monitor
Enable REFA
present monitor switchover (manual
Select REFB
Stay on
REFB
Use REF_SEL
pin for
Enable
switchover
and monitors
FB clock
present
monitor
automatic
reference
switchover
deglitch
register
mode)
reference
switchover
0x01B
0x01C
Reserved
Reserved
= 0
Reserved = 0
Reserved = 0
Reserved =
0
Reserved = 0
Reserved = 0
Reserved = 0
0x00
0x22
PLL block PD
register
N divider N divider PD
ECL 2
R Divider B ECL 2
CMOS PD
R Divider A R Divider B PD
R
R Channel B
PD
R Channel A
PD
ECL 2
CMOS PD
Divider A
PD
CMOS PD
0x01F
PLL readback
Unused
Unused
Unused
Selected
reference
Status FB clock
Don't care
Status
REFB
Status REFA
Digital lock
detect (DLD)
N/A
PECL/CMOS Outputs
0x0F0
LVPECL OUT0
Don’t
care
Don’t care
Don’t care
Power
down
OUT0 PECL output level,
Bits[1:0]
Power down
PECL driver
0x04
Channel 0,
Channel 1
0x0F1
0x0F2
LVPECL OUT1
LVPECL OUT2
Don’t
care
Don’t care
Don’t care
Don’t care
Don’t care
Reserved
Don't care
Don't care
OUT1 PECL output level,
Bits[1:0]
Power down
PECL driver
0x04
0x04
Don’t
care
Power
down
OUT2 PECL output level,
Bits[1:0]
Power down
PECL driver
Channel 2,
Channel 3
0x0F3
LVPECL OUT3
Don’t
care
Don’t care
Don’t care
Reserved
Don't care
OUT3 PECL output level,
Bits[1:0]
Power down
PECL driver
0x04
Rev. 0 | Page 31 of 48
AD9525
Data Sheet
Reg.
Addr.
(Hex)
Default
Value
(Hex)
Register
Name
(MSB)
Bit 7
(LSB)
Bit 0
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
0x0F4
LVPECL OUT4
Don't
care
Don't care
Don't care
Power
down
Don't care
OUT4 PECL output level,
Bits[1:0]
Power down
PECL driver
0x04
Channel 4,
Channel 5
0x0F5
0x0F6
LVPECL OUT5
LVPECL OUT6
Don't
care
Don't care
Don't care
Don't care
Don't care
Reserved
Don't care
Don't care
OUT5 PECL output level,
Bits[1:0]
Power down
PECL driver
0x04
0x04
Don't
care
Power
down
OUT6 PECL output level,
Bits[1:0]
Power down
PECL driver
Channel 6,
Channel 7
0x0F7
0x0F8
LVPECL OUT7
Sync output
Don't
care
Don't care
Don't care
Don't care
Don't care
Reserved
Don't care
Don't care
OUT7 PECL output level,
Bits[1:0]
Power down
PECL driver
0x04
0x10
Don't
care
Power
down sync
channel
SYNC_OUT PECL output
level, Bits[1:0]
Power down
PECL driver
0x0F9
0x0FA
Sync output,
other control
Don't
care
Don't care
Don't care
Don't care
Don't care
Polarity
CMOS
mode
Enable CMOS drivers,
Bits[1:0]
CMOS mode
Don't care
Sync out
resampling
edge select
0x00
0x00
Drivers
reserved
Don't
care
Don't care
Don't care
Don't
care
Don't care
SYNC Control
0x190 Sync clock
S divider
Sync clock S divider, Bits[7:0]
Sync clock S divider, Bits[15:8]
0x00
0x00
0x00
0x191 Sync clock
S divider
0x192 Sync clock
control
Don't
care
Don't care
Don't care
Don't care
Don't care
Don't care
Don't care
Sync
Sync source, Bits[1:0]
Sync mode, Bits[1:0]
enable
VCO, Reference and CLK1 Inputs
0x1E0
VCO divider
Don't
care
Don't care
Don't care
M divider, Bits[2:0]
0x00
0x00
Other
0x230 Power-down
0x232 IO_UPDATE
Don't
care
Dist all
power-
down
CLKIN power-
down
M
Distribution
reference
PLL power-
down
divider
power-
down
power-down
Don't
care
Don't care
Don't care
Don't care
Don't care
Don't
care
Don't care
IO_UPDATE
0x00
Rev. 0 | Page 32 of 48
Data Sheet
AD9525
REGISTER MAP DESCRIPTIONS
Table 29 through Table 49 provide a detailed description of each of the control register functions. The registers are listed by hexadecimal
address.
Table 29. SPI Mode Serial Port Configuration
Reg.
Addr.
(Hex)
Bits
Bit Name
Description
0x000
7
SDO active
Selects unidirectional or bidirectional data transfer mode.
0: SDIO pin used for write and read; SDO is high impedance (default).
1: SDO used for read; SDIO used for write; unidirectional mode.
SPI MSB or LSB data orientation. (This register is ignored in I2C mode.)
0: data-oriented MSB first; addressing decrements (default).
1: data-oriented LSB first; addressing increments.
Soft reset.
6
5
LSB first/address
increase
Soft reset
1 (self-clearing): soft reset; restores default values to internal registers.
Unused.
4
Unused
[3:0]
Mirror[7:4]
Bits[3:0] should always mirror Bits[7:4] so that it does not matter whether the part is in MSB or LSB first mode
(see Register 0x000[6]). Set bits as follows:
Bit 0 = Bit 7
Bit 1 = Bit 6
Bit 2 = Bit 5
Bit 3 = Bit 4
0x004
0
Read back
active registers
Select register bank used for a readback.
0: reads back buffer registers (default).
1: reads back active registers.
Table 30. PFD Charge Pump
Reg.
Addr.
(Hex) Bits
Bit Name
Description
0x010
7
PFD polarity
Sets the PFD polarity.
0: Positive (higher control voltage produces higher frequency) (default).
1: Negative (higher control voltage produces lower frequency).
Charge pump current (with CPRSET = 5.1 kΩ).
[6:4]
CP current
Bit 6
Bit 5
Bit 4
ICP (mA)
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0.6
1.2
1.8
2.4
3.0
3.6
4.2
4.8 (default)
[3:2]
[1:0]
CP mode
Charge pump operating mode.
Bit 3
Bit 2
Charge Pump Mode
0
0
1
1
0
1
0
1
High impedance state
Force source current (pump-up)
Force sink current (pump-down)
Normal operation (default)
Antibacklash
pulse width
See Table 7 for the maximum operating frequency for each setting.
Bit 1
Bit 0
Antibacklash Pulse Width Mode (ns)
0
0
1
1
0
1
0
1
2.9 (default)
1.3
6.0
2.9
Rev. 0 | Page 33 of 48
AD9525
Data Sheet
Table 31. REFA, REFB, REFC, B, N, and P Dividers
Reg.
Addr.
(Hex) Bits
Bit Name
Description
0x011 [7:4] REFB divider output Divider high cycle word. Normally set to one-half desired divider division minus one:
high cycles
for example, D/2 – 1; therefore, for Divide = 8, set to 0x03 (8/2 – 1).
Number of clock cycles (minus 1) of the divider input during which the divider output stays high. A
value of 0x7 means that the divider is low for eight input clock cycles (default: 0x0).
[3:0] REFB divider output Divider low cycle word. Normally set to one-half desired divider division minus one:
low cycles
for example, D/2 – 1; therefore, for Divide = 8, set to 0x03 (8/2 – 1).
Number of clock cycles (minus 1) of the divider input during which the divider output stays high. A
value of 0x7 means that the divider is low for eight input clock cycles (default: 0x0).
0x012 [7:4] REFA divider output Divider high cycle word. Normally set to one-half desired divider division minus one:
high cycles
for example, D/2 – 1; therefore, for Divide = 8, set to 0x03 (8/2 – 1).
Number of clock cycles (minus 1) of the divider input during which the divider output stays low. A
value of 0x7 means the divider is high for eight input clock cycles (default: 0x0).
[3:0] REFA divider output Divider low cycle word. Normally set to one-half desired divider division minus one:
low cycles
for example, D/2 – 1; therefore, for Divide = 8, set to 0x03 (8/2 – 1).
Number of clock cycles (minus 1) of the divider input during which the divider output stays high. A
value of 0x7 means that the divider is low for eight input clock cycles (default: 0x0).
0x013 [7:4] B divider output
high cycles
Divider high cycle word. Normally set to one-half desired divider division minus one:
for example, D/2 – 1; therefore, for Divide = 8, set to 0x03 (8/2 – 1).
Number of clock cycles (minus 1) of the divider input during which the divider output stays low. A
value of 0x7 means the divider is high for eight input clock cycles (default: 0x0).
[3:0] B divider output
low cycles
Divider low cycle word. Normally set to one-half desired divider division minus one:
for example, D/2 – 1; therefore, for Divide = 8, set to 0x03 (8/2 – 1).
Number of clock cycles (minus 1) of the divider input during which the divider output stays high. A
value of 0x7 means that the divider is low for eight input clock cycles (default: 0x0).
0x014 [7:6] Don’t care
Don’t care.
5
4
3
B divider bypass
Bypasses and powers down the B divider; routes input to divider output.
0: uses divider (default).
1: B divider is set to divide-by-1.
REFB divider bypass Bypasses and powers down the divider; routes input to divider output.
0: uses divider (default).
1: REFB divider is set to divide-by-1.
REFA divider bypass Bypasses and powers down the divider; routes input to divider output.
0: use divider (default).
1: REFA divider is set to divide-by-1.
[2:0] P divider prescaler
P divider value (B divider prescaler).
Bit 2 Bit 1 Bit 0 Divider Value
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
1(default)
2
3
4
5
6
Static
Static
0x015
7
6
5
4
3
Don’t care
Reserved
Don’t care.
0 (default).
0 (default).
0 (default).
Resets B divider.
Reserved
Reserved
B divider reset
0: normal operation (default).
1: holds B divider in reset.
Rev. 0 | Page 34 of 48
Data Sheet
AD9525
Reg.
Addr.
(Hex) Bits
Bit Name
Description
2
REFB divider reset
REFA divider reset
Reset all dividers
REFC enable
Resets REFB divider.
0: normal (default).
1: holds REFB divider in reset.
Resets REFA divider.
1
0
0: normal (default).
1: holds REFA divider in reset.
Resets REFA, REFB, B divider (B divider is part of N divider).
0: normal (default).
1: holds REFA, REFB, B divider in reset.
Enables REFC path.
0x016
7
0: disabled (default).
1: enables REFC path.
[6:0] REFC divider
7-bit REFC divider. Divide-by-1 to divide-by-127.
0000000, 0000001: both divide-by-1 (default: 0x00).
Table 32. Status Pin and Other
Reg.
Addr.
(Hex)
Bits Bit Name
Description
0x017
7
Charge pump pin
to VDD_CP/2
Sets the charge pump pin to one-half of the VDD_CP supply voltage.
0: charge pump normal operation (default).
1: charge pump pin set to VDD_CP/2.
6
STATUS pin divider
enable
Enables STATUS pin divider.
0: disabled (default).
1: enables divider.
[5:0] STATUS output
select
Selects the signal that appears at the STATUS pin. Register 0x017[6] must be set to 0 to for any mode
identified as LVL.
Level or
Dynamic
Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Signal
Signal at STATUS Pin
Ground, dc (default).
N divider output.
Ground, dc.
Ground, dc.
Ground, dc.
PFD up pulse.
PFD down pulse.
Ground (dc); for all other cases of 0XXXXX
not specified.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
X
0
0
0
0
0
0
0
X
0
0
0
0
1
1
1
X
0
0
1
1
0
0
1
X
0
1
0
1
0
1
0
X
LVL
DYN
LVL
LVL
LVL
DYN
DYN
LVL
The selections that follow are the same
as for the REF_MON pin.
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
0
1
1
0
0
0
1
0
1
0
1
LVL
Ground (dc).
REFA clock.
REFB clock.
Selected reference clock to PLL.
Unselected reference clock to PLL.
DYN
DYN
DYN
DYN
LVL
Both REFA and REFB clocks missing
(active high).
1
1
1
1
0
0
0
0
0
0
1
1
1
1
0
0
1
1
0
0
0
1
0
1
LVL
LVL
LVL
LVL
Ground, dc.
REFA present (active high).
REFB present (active high).
(REFA present) AND (REFB present).
Rev. 0 | Page 35 of 48
AD9525
Data Sheet
Reg.
Addr.
(Hex)
Bits Bit Name
Description
Level or
Dynamic
Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Signal
Signal at STATUS Pin
1
0
1
0
1
0
LVL
(DLD) AND (selected reference present)
AND (feedback clock present).
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
1
0
1
LVL
LVL
LVL
LVL
LVL
LVL
DYN
DYN
DYN
DYN
LVL
Feedback clock present (active high).
Selected reference (low: REFA, high: REFB).
DLD; active high.
N/A.
Ground (dc).
VDD3 (PLL power supply).
REFA clock.
REFB clock.
Selected reference to PLL.
Unselected reference to PLL.
Status of selected reference (status of
differential reference); active low.
1
1
1
1
1
1
1
1
1
1
0
0
1
1
1
1
1
0
0
0
1
1
0
0
1
0
1
0
1
0
LVL
LVL
LVL
LVL
LVL
Both reference clocks missing; active low.
REFA present (active low).
REFB present (active low).
(REFA present) AND (REFB present).
(DLD) AND (selected reference present)
AND (feedback clock present); (active low).
1
1
1
1
1
1
0
1
1
0
1
0
LVL
LVL
Feedback clock present
Selected reference (low = REFA, high =
REFB); active low.
1
1
1
1
1
1
1
1
1
1
1
1
0
1
1
1
0
1
LVL
LVL
LVL
DLD (active low).
N/A.
VDD3 (PLL power supply).
Rev. 0 | Page 36 of 48
Data Sheet
AD9525
Table 33. REF_MON Pin Control
Reg.
Addr.
Bit
(Hex) Bits Name
Description
0x018 [7:5] Don’t
care
Don’t care.
[4:0] REF_MON Selects the signal that is connected to the REF_MON pin.
pin
control
Level or
Dynamic
Bit 4 Bit 3
Bit 2 Bit 1
Bit 0 Signal
Signal at REF_MON Pin
Ground (dc).
REFA clock.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
1
0
1
0
LVL
DYN
DYN
DYN
DYN
LVL
LVL
LVL
LVL
LVL
LVL
REFB clock.
Selected reference clock to PLL.
Unselected reference clock to PLL.
Both reference clocks missing (active high).
Ground (dc).
Status REF A frequency (active high).
Status REF B frequency (active high).
(Status REF A frequency) AND (status REF B frequency).
(DLD) AND (status of selected reference) AND (status of feedback
clock).
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
LVL
LVL
LVL
LVL
LVL
LVL
DYN
DYN
DYN
DYN
LVL
LVL
Status of feedback clock (active high).
Selected reference (low: REFA, high: REFB).
DLD; active high.
N/A.
Ground, dc.
VDD3 (PLL power supply).
REFA
.
REFB
.
Selected reference to PLL
.
Unselected reference to PLL
.
Status of selected reference (status of differential reference); active low.
Status of unselected reference (not available in differential mode);
active low.
1
1
1
1
1
1
1
1
1
0
1
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
1
0
0
1
1
0
0
1
1
1
0
1
0
1
0
1
0
1
LVL
LVL
LVL
LVL
LVL
LVL
LVL
LVL
LVL
Status of REF A frequency (active low).
Status of REF B frequency (active low).
(Status of REFA frequency) AND (status of REFB frequency)
.
(DLD) AND (status of selected reference) AND (status of feedback clock)
.
Status of feedback clock (active low).
Selected reference (low: REFA, high: REFB); active low.
DLD (active low).
N/A.
VDD3 (PLL power supply).
Rev. 0 | Page 37 of 48
AD9525
Data Sheet
Table 34. Lock Detect
Reg.
Addr.
(Hex) Bits
0x019 [7:4]
[3:2]
Bit Name
Description
Don’t care
Don’t care.
Lock detect
counter
Required consecutive number of PFD cycles with edges inside lock detect window before the DLD
indicates a locked condition.
Bit 3
Bit 2
PFD Cycles to Determine Lock
0
0
1
1
0
1
0
1
5 (default)
16
64
255
1
0
Digital lock detect
window
If the time difference of the rising edges at the inputs to the PFD is less than the lock detect window time,
the digital lock detect flag is set. The flag remains set until the time difference is greater than the loss-
of-lock threshold.
0: high range (default).
1: low range.
Digital lock detect
disable
Digital lock detect operation.
0: normal lock detect operation (default).
1: disables lock detect.
Table 35. Reference Switchover and Monitors
Reg.
Addr.
(Hex)
Bits
Bit Name
Description
0x01A
7
Enable feedback
clock present
monitor
Enables feedback clock monitor. The presence of a feedback clock is checked with the selected
reference to the PLL. This monitor does not have a value output if there is no reference to the PLL.
0: disables monitor (default).
1: enables monitor.
6
5
Enable REFB
present monitor
Enables Reference B clock monitor. The presence of the REFB clock is checked with the feedback clock
to the PLL. This monitor does not have a value output if there is no feedback clock to the PLL.
Register 0x01C[5] = 0 (on) for monitor to work.
0: disables monitor (default).
1: enables monitor.
Enable REFA
present monitor
Enables Reference A clock monitor. The presence of the REFA clock is checked with the feedback clock
to the PLL. This monitor does not have a value output if there is no feedback clock to the PLL.
Register 0x01C[4] = 0 (on) for monitor to work.
0: disables monitor (default).
1: enables monitor.
4
3
2
1
0
Disable switchover Disables or enables the switchover deglitch circuit.
deglitch
0: enables switchover deglitch circuit (default).
1: disables switchover deglitch circuit.
If Register 0x01A[1] = 0, selects reference for PLL.
0: selects REFA.
Select REFB
(manual register
mode)
1: selects REFB.
Stay on REFB
Stays on REFB after switchover.
0: returns to REFA automatically when REFA status is good again.
1: stays on REFB after switchover. Do not automatically return to REFA.
If Register 0x01A[0] = 0 (manual), sets method of PLL reference selection.
0: uses Register 0x01A[3] (default).
Use REF_SEL pin
for reference
switchover
1: uses REF_SEL pin.
Enable automatic
ref switchover
Automatic or manual reference switchover.
0: manual reference switchover.
1: automatic reference switchover.
Rev. 0 | Page 38 of 48
Data Sheet
AD9525
Table 36. Reserved
Reg.
Addr.
(Hex) Bits Bit Name
Description
0x01B [7:0] Reserved
Reserved.
0: default. All bits should be set to 0.
Table 37. PLL Block Power-Down
Reg.
Addr.
(Hex) Bits Name
Description
0x01C
7
6
5
N divider
ECL 2 CMOS
power-down
Turns off the N divider’s output clock. This stops the clock to the PFD and the frequency monitors.
0: clock on (default).
1: clock off.
N divider
power-down
N divider power-down.
0: N divider on (default).
1: N divider off.
This bit stops the clock to the frequency monitors for REFB. If this bit is disabled, the automatic reference
switchover does not operate. In some configurations, enabling the REFB divider ECL 2 CMOS may increase
reference spurs on clock outputs.
REFB Divider
ECL 2 CMOS
power-down
0: on.
1: off (default).
4
REFA Divider
ECL 2 CMOS
power-down
This bit stops the clock to the frequency monitors for REFA. If this bit is disabled, the automatic reference
switchover does not operate. In some configurations, enabling the REFA Divider ECL 2 CMOS may
increase reference spurs on clock outputs.
0: on (default).
1: off.
3
2
1
0
REFB divider
power-down
Powers down REFB divider. The REFB input receiver is still powered up.
0: REFB divider on (default).
1: REFB divider off.
REFA divider
power-down
Powers down REFA divider. The REFA input receiver is still powered up.
0: REFA divider on (default).
1: REFA divider off.
REFB channel
power-down
Powers down REFB channel. The REFB input receiver is powered down.
0: REFB channel on.
1: REFB channel off (default).
REFA channel
power-down
Powers down REFA channel. The REFA input receiver is powered down.
0: REFA channel on (default).
1: REFA channel off.
Rev. 0 | Page 39 of 48
AD9525
Data Sheet
Table 38. PLL Readback
Reg.
Addr.
(Hex) Bits
Bit Name
Description
0x01F [7:5] Unused
Unused
4
3
Selected reference
Shows the reference used by the PLL
0: REFA
1: REFB
Status feedback clock
Status REFB
Status of the feedback clock, as determined by the selected reference
0: missing
1: present
2
1
0
Status of Reference B clock, as determined by the feedback clock
0: missing
1: present
Status REFA
Status of Reference A clock, as determined by the feedback clock
0: missing
1: present
Digital lock detect (DLD)
Digital lock detect
0: PLL not locked
1: PLL locked
Table 39. LVPECL Drivers OUT0
Reg.
Addr.
(Hex)
Bits
Bit Name
Description
0x0F0
[7:5] Don’t care
Don’t care
4
3
Power down Channel 0 and
Channel 1
Powers down Channel 0 and Channel 1
0: enabled (default)
1: power-down
Don’t care
Don’t care
[2:1] OUT0 level
Bit 1 Bit 0
VOD (mV)
0
0
1
1
0
1
0
1
400
600
780 (default)
960
0
OUT0 driver power-down
0: enabled (default)
1: power-down
Table 40. LVPECL Drivers OUT1
Reg.
Addr.
(Hex)
Bits
Bit Name
Description
0x0F1
[7:5] Don’t care
Don’t care
4
3
Reserved
Reserved, write 0
Don’t care
Don’t care
[2:1] OUT1 level
Bit 1 Bit 0 VOD (mV)
0
0
1
1
0
1
0
1
400
600
780 (default)
960
0
OUT1 driver power-down
0: enabled (default)
1: power-down
Rev. 0 | Page 40 of 48
Data Sheet
AD9525
Table 41. LVPECL Drivers OUT2
Reg.
Addr.
(Hex) Bits
0x0F2 [7:5]
4
Bit Name
Description
Don’t care
Don’t care
Power down
Channel 2 and
Channel 3
Powers down Channel 2 and Channel 3
0: enabled (default)
1: power-down
3
Don’t care
OUT2 level
Don’t care
[2:1]
Bit 1 Bit 0
VOD (mV)
400
0
0
1
1
0
1
0
1
600
780 (default)
960
0
OUT2 driver
power-down
0: enabled (default)
1: power-down
Table 42. LVPECL Drivers OUT3
Reg.
Addr.
(Hex) Bits Bit Name
Description
0x0F3 [7:5] Don’t care
Don’t care
4
3
Reserved
Reserved, write 0
Don’t care
Don’t care
[2:1] OUT3 level
Bit 1 Bit 0
VOD (mV)
400
0
0
1
1
0
1
0
1
600
780 (default)
960
0
OUT3 driver
power-down
0: enabled (default)
1: power-down
Table 43. PECL Drivers OUT4
Reg.
Addr.
(Hex) Bits Bit Name
Description
0x0F4 [7:5] Don’t care
Don’t care
4
Power down
Channel 4 and
Channel 5
Powers down Channel 4 and Channel 5
0: enabled (default)
1: power-down
3
Don’t care
Don’t care
[2:1] OUT4 level
Bit 1 Bit 0
VOD (mV)
0
0
1
1
0
1
0
1
400
600
780 (default)
960
0
OUT4 driver
power-down
0: enabled (default)
1: power-down
Rev. 0 | Page 41 of 48
AD9525
Data Sheet
Table 44. LVPECL Drivers OUT5
Reg.
Addr.
(Hex)
Bits Bit Name
Description
0x0F5
[7:5] Don’t care
Don’t care
4
3
Reserved
Reserved, write 0
Don’t care
Don’t care
[2:1] OUT5 level
Bit 1 Bit 0 VOD (mV)
0
0
1
1
0
1
0
1
400
600
780 (default)
960
0
OUT5 driver
power-down
0: enabled (default)
1: power-down
Table 45. LVPECL Drivers OUT6
Reg.
Addr.
(Hex)
Bits Bit Name
Description
0x0F6
[7:5]
Don’t care
4
Power down
Channel 6 and
Channel 7
Power down Channel 6 and Channel 7
0: enabled (default)
1: power-down
3
Don’t care
[2:1] OUT6 level
Bit 1 Bit 0 VOD (mV)
0
0
1
1
0
1
0
1
400
600
780 (default)
960
0
OUT6 driver
power-down
0: enabled (default)
1: power-down
Table 46. LVPECL Drivers OUT7
Reg.
Addr.
(Hex)
Bits Bit Name
Description
0x0F7
[7:5] Don’t care
Don’t care
4
3
Reserved
Reserved, write 0
Don’t care
Don’t care
[2:1] OUT7 level
Bit 1 Bit 0 VOD (mV)
0
0
1
1
0
1
0
1
400
600
780 (default)
960
0
OUT7 driver
power-down
0: enabled (default)
1: power-down
Rev. 0 | Page 42 of 48
Data Sheet
AD9525
Table 47. SYNC_OUT Control
Reg.
Addr.
(Hex) Bits Bit Name
Description
0x0F8 [7:5] Don’t care
Don’t care.
4
SYNC_OUT
channel
Powers down SYNC_OUT channel.
0: enabled.
power-down
1: power-down (default).
3
Sync polarity
Polarity LVPECL mode.
0: noninverting (default).
1: inverting.
[2:1] SYNC_OUT
level
Bit 1
Bit 0
VOD (mV)
0
0
1
1
0
1
0
1
400 (default)
600
780
960
0
SYNC_OUT
driver
0: enabled (default).
1: powers down LVPECL SYNC_OUT driver.
power-down
0x0F9 [7:5] Don’t care
Polarity CMOS
mode
Don’t care.
4
Polarity CMOS mode. This bit is also used in conjunction with Register 0x0F8[3] when the driver is in CMOS
mode (Register 0x0F9[1] = 1).
Reg. 0x0F9[4]
Reg. 0x0F8[3]
SYNC OUT/SYNC OUTB
0
0
1
1
0
1
0
1
Noninverting/noninverting
Inverting/inverting
Noninverting/inverting
Inverting/noninverting
[3:2] Enable CMOS
drivers
Sets the CMOS driver output configuration when Register 0x0F9[1] = 1.
SYNC_OUT
Bit 3
Bit 2
SYNC_OUT
0
0
1
1
0
1
0
1
Tristate
On
Tristate
On
Tristate
Tristate
On
On
1
0
CMOS mode
Use CMOS mode instead of LVPECL mode for SYNC_OUT.
0: LVPECL mode (default).
1: CMOS mode.
Sync out
resampling
edge select
SYNC_OUT resample edge select. Selects the M divider output edge used to resample the sync clock.
0: use rising edge of M clock (default).
1: use falling edge of M clock.
0x190 [7:0] Sync clock
S divider
16-bit sync S divider, Bits[7:0] (LSB).
Cycles of reference clock = S Divider Bits[15:0] + 1. For example, [15:0] = 0 is 1 reference clock cycles,
[15:0] = 1 is 2 reference clock cycles … [15:0] = 65535 is 65536 reference clock cycles.
0x191 [7:0] Sync clock
S divider
16-bit sync S divider, Bits[15:8] (MSB).
0x192 [7:5] Don’t care
Don’t care.
4
Sync enable
0: disable SYNC_OUT (default).
1: Enable SYNC_OUT.
Note: Self-clearing for single shot sync.
[3:2] Sync source
[1:0] Sync mode
Bit 1
Bit 0
Select Reference for SYNC Clock
0
0
1
1
0
1
0
1
REF: reference input (default)
FB: PLL feedback N divider
Power-down: power down SYNC
Power-down: power down SYNC
Bit 1
Bit 0
Sync Mode
0
0
1
1
0
1
0
1
Single shot (default)
Periodic
Pseudorandom
Pseudorandom
Rev. 0 | Page 43 of 48
AD9525
Data Sheet
Table 48. VCO, Reference, and CLK Inputs
Reg.
Addr.
(Hex) Bits
Bit Name
Description
Don’t care.
0x1E0 [7:3] Don’t care
[2:0] M divider
M divider value.
Bit 2
Bit 1
Bit 0
Divider Value
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
1
2
3
4
5
6
7
8
Table 49. Other
Reg.
Addr.
(Hex) Bits
Name
Description
0x230 [7:5] Don’t care
Don’t care.
4
3
2
1
Dist all power-down
Powers down all of distribution. Puts all drivers in safe power-down mode.
0 (default): enabled.
1: power-down.
CLKIN power-down
Powers down CLKIN, CLKIN.
0 (default): enabled.
1: power-down.
M divider power-down Powers down M divider.
0 (default): enabled.
1: power-down.
Distribution reference
power-down
Power down distribution reference. This bit should be asserted only when the drivers do not
need the safe power-down mode guidelines.
0 (default): enabled.
1: power-down.
0
PLL power-down
Power down PLL.
0 (default): enabled.
1: power-down.
232
[7:1] Don’t care
IO_UPDATE
Don’t care.
0
This bit must be set to 1b to transfer the contents of the buffer registers into the active registers.
This happens on the next SCLK rising edge. This bit is self-clearing; that is, it does not have to be
set back to 0.
1 (self-clearing): update all active registers to the contents of the buffer registers.
Rev. 0 | Page 44 of 48
Data Sheet
AD9525
APPLICATIONS INFORMATION
Figure 34 shows the required sampling clock jitter as a function
of the analog frequency and effective number of bits (ENOB).
FREQUENCY PLANNING USING THE AD9525
The AD9525 is a highly flexible PLL. When choosing the PLL
settings and version of the AD9525, the following guidelines
should be kept in mind.
110
18
1
SNR = 20log
2πfAtJ
100
90
80
70
60
50
40
30
16
14
12
10
8
The AD9525 has three frequency dividers: the reference (or R)
divider, the feedback (or N) divider, and the M divider. When
trying to achieve a particularly difficult frequency divide ratio
requiring a large amount of frequency division, some of the
frequency division can be done by either the M divider or the
N divider, thus allowing a higher phase detector frequency and
more flexibility in choosing the loop bandwidth.
tJ
tJ
tJ
=
=
=
100f
200f
400f
s
s
s
tJ
tJ
=
=
1p
s
2p
s
tJ
=
10p
s
Choosing a nominal charge pump current in the middle of the
allowable range as a starting point allows the designer to increase or
decrease the charge pump current and, thus, allows the designer
to fine-tune the PLL loop bandwidth in either direction.
6
10
100
fA (MHz)
1k
Figure 34. SNR and ENOB vs. Analog Input Frequency
ADIsimCLK is a powerful PLL modeling tool that can be
downloaded from www.analog.com. It is very accurate in
determining the optimal loop filter for a given application.
For more information, see the AN-756 Application Note,
Sampled Systems and the Effects of Clock Phase Noise and Jitter,
and the AN-501 Application Note, Aperture Uncertainty and
ADC System Performance, at www.analog.com.
USING THE AD9525 OUTPUTS FOR ADC CLOCK
APPLICATIONS
Many high performance ADCs feature differential clock inputs
to simplify the task of providing the required low jitter clock on
a noisy PCB. Distributing a single-ended clock on a noisy PCB can
result in coupled noise on the sampling clock. Differential distri-
bution has inherent common-mode rejection that can provide
superior clock performance in a noisy environment. The
differential LVPECL outputs of the AD9525 enable clock
solutions that maximize converter SNR performance.
Any high speed ADC is extremely sensitive to the quality of the
sampling clock of the AD9525. An ADC can be thought of as a
sampling mixer, and any noise, distortion, or time jitter on the
clock is combined with the desired signal at the analog-to-digital
output. Clock integrity requirements scale with the analog input
frequency and resolution, with higher analog input frequency
applications at ≥14-bit resolution being the most stringent. The
theoretical SNR of an ADC is limited by the ADC resolution and
the jitter on the sampling clock. Considering an ideal ADC of
infinite resolution, where the step size and quantization error
can be ignored, the available SNR can be expressed, approxi-
mately, by
The input requirements of the ADC (differential or single-ended,
logic level termination) should be considered when selecting
the best clocking/converter solution.
1
SNR(dB) = 20 log
2πfAtJ
where:
fA is the highest analog frequency being digitized.
tJ is the rms jitter on the sampling clock.
Rev. 0 | Page 45 of 48
AD9525
Data Sheet
LVPECL CLOCK DISTRIBUTION
SYNC_OUT DISTRIBUTION
The LVPECL outputs (because they are open emitter) require
a dc termination to bias the output transistors. The simplified
equivalent circuit in Figure 22 shows the LVPECL output stage.
The SYNC_OUT driver of the AD9525 can be configured as
CMOS drivers. When selected for use as CMOS drivers, each
output becomes a pair of CMOS outputs, each of which can be
individually turned on or off and set as inverting or noninverting.
Be sure to note the skew difference of using CMOS mode vs.
LVPECL mode.
In most applications, a LVPECL far-end Thevenin termination
(see Figure 35) or Y-termination (see Figure 36) is
recommended. In both cases, VS of the receiving buffer should
match VS_DRV (VS_DRV = VDD3). If it does not match, ac
coupling is recommended (see Figure 37).
When single-ended CMOS clocking is used, refer to the guidelines
presented in the following paragraphs.
VS_DRV
Point-to-point connections should be designed such that each
driver has only one receiver, if possible. Connecting outputs in
this manner allows for simple termination schemes and minimizes
ringing due to possible mismatched impedances on the output
trace. Series termination at the source is generally required to
provide transmission line matching and/or to reduce current
transients at the driver.
VS_DRV
V
S
127Ω
127Ω
50Ω
SINGLE-ENDED
(NOT COUPLED)
LVPECL
LVPECL
50Ω
83Ω
83Ω
The value of the resistor is dependent on the board design and
timing requirements (typically 10 Ω to 100 Ω is used). CMOS
outputs are also limited in terms of the capacitive load or trace
length that they can drive. Typically, trace lengths less than 3 inches
are recommended to preserve signal rise/fall times and signal
integrity.
Figure 35. DC-Coupled 3.3 V LVPECL Far-End Thevenin Termination
VS_DRV
V
= VS_DRV
LVPECL
S
Z
Z
= 50Ω
= 50Ω
0
50Ω
50Ω
50Ω
LVPECL
60.4Ω
(1.0 INCH)
10Ω
CMOS
CMOS
0
MICROSTRIP
Figure 36. DC-Coupled 3.3 V LVPECL Y-Termination
Figure 38. Series Termination of CMOS Output
Termination at the far end of the PCB trace is a second option.
The SYNC_OUT CMOS output of the AD9525 does not supply
enough current to provide a full voltage swing with a low
impedance resistive, far-end termination, as shown in Figure 39.
The far-end termination network should match the PCB trace
impedance and provide the desired switching point. The reduced
signal swing may still meet receiver input requirements in some
applications. This can be useful when driving long trace lengths
on less critical nets.
VS_DRV
V
S
0.1nF
100Ω DIFFERENTIAL
(COUPLED)
100Ω
LVPECL
LVPECL
0.1nF
TRANSMISSION LINE
200Ω
200Ω
Figure 37. AC-Coupled LVPECL with Parallel Transmission Line
V
LVPECL Y-termination is an elegant termination scheme that
uses the fewest components and offers both odd- and even-mode
impedance matching. Even-mode impedance matching is an
important consideration for closely coupled transmission lines
at high frequencies. Its main drawback is that it offers limited
flexibility for varying the drive strength of the emitter-follower
LVPECL driver. This can be an important consideration when
driving long trace lengths but is usually not an issue.
S
100Ω
50Ω
10Ω
CMOS
CMOS
100Ω
Figure 39. CMOS Output with Far-End Termination
Because of the limitations of single-ended CMOS clocking,
consider using differential outputs when driving high speed
signals over long traces. The AD9525 offers SYNC_OUT
LVPECL outputs that are better suited for driving long traces
where the inherent noise immunity of differential signaling
provides superior performance for clocking converters.
Thevenin-equivalent termination uses a resistor network to
provide 50 Ω termination to a dc voltage that is below VOL of
the LVPECL driver. In this case, VS_DRV on the AD9525
should equal VS of the receiving buffer. Although the resistor
combination shown results in a dc bias point of VS_DRV − 2 V,
the actual common-mode voltage is VS_DRV − 1.3 V because
there is additional current flowing from the AD9525 LVPECL
driver through the pull-down resistor.
Rev. 0 | Page 46 of 48
Data Sheet
AD9525
OUTLINE DIMENSIONS
7.00
BSC SQ
0.30
0.23
0.18
PIN 1
INDICATOR
PIN 1
INDICATOR
48
37
36
1
0.50
BSC
EXPOSED
PAD
5.20
5.10 SQ
5.00
12
13
25
24
0.45
0.40
0.35
0.25 MIN
TOP VIEW
BOTTOM VIEW
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
0.80
0.75
0.70
0.05 MAX
0.02 NOM
SECTION OF THIS DATA SHEET.
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-220-WKKD.
Figure 40. 48-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
7 mm × 7 mm Body, Very Very Thin Quad
CP-48-4
Dimensions shown in millimeters
ORDERING GUIDE
Model1
Temperature Range
−40°C to +85°C
−40°C to +85°C
Package Description
Package Option
AD9525BCPZ
48-Lead Lead Frame Chip Scale Package (LFCSP_WQ)
48-Lead Lead Frame Chip Scale Package (LFCSP_WQ)
Evaluation Board, No VCO
CP-48-4
CP-48-4
AD9525BCPZ-REEL7
AD9525/PCBZ
AD9525/PCBZ-VCO
Evaluation Board, 2950 MHz VCO Installed
1 Z = RoHS Compliant Part.
Rev. 0 | Page 47 of 48
AD9525
NOTES
Data Sheet
©2012 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D10011-0-10/12(0)
Rev. 0 | Page 48 of 48
相关型号:
©2020 ICPDF网 联系我们和版权申明