AD9634 [ADI]
12-Bit, 170 MSPS/210 MSPS/250 MSPS; 12位, 170 MSPS / 210 MSPS / 250 MSPS型号: | AD9634 |
厂家: | ADI |
描述: | 12-Bit, 170 MSPS/210 MSPS/250 MSPS |
文件: | 总32页 (文件大小:1575K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
12-Bit, 170 MSPS/210 MSPS/250 MSPS,
1.8 V Analog-to-Digital Converter
AD9634
FUNCTIONAL BLOCK DIAGRAM
FEATURES
AVDD
AGND
DRVDD
SNR = 69.7 dBFS at 185 MHz AIN and 250 MSPS
SFDR = 87 dBc at 185 MHz AIN and 250 MSPS
−150.6 dBFS/Hz input noise at 185 MHz, −1 dBFS AIN and
250 MSPS
Total power consumption: 360 mW at 250 MSPS
1.8 V supply voltages
VIN+
PIPELINE
12-BIT
ADC
12
D0±/D1±
.
.
.
VIN–
VCM
PARALLEL
DDR LVDS
AND
AD9634
D10±/D11±
DRIVERS
LVDS (ANSI-644 levels) outputs
Integer 1-to-8 input clock divider (625 MHz maximum input)
Sample rates of up to 250 MSPS
IF sampling frequencies of up to 350 MHz
Internal ADC voltage reference
REFERENCE
DCO±
OR±
1-TO-8
CLOCK DIVIDER
SERIAL PORT
Flexible analog input range
SCLK SDIO
CSB
CLK+
CLK–
1.4 V p-p to 2.0 V p-p (1.75 V p-p nominal)
ADC clock duty cycle stabilizer
Figure 1.
Serial port control
Energy-saving power-down modes
User-configurable, built-in self test (BIST) capability
APPLICATIONS
Communications
Diversity radio systems
Multimode digital receivers (3G)
TD-SCDMA, WiMAX, W-CDMA, CDMA2000, GSM, EDGE, LTE
I/Q demodulation systems
Smart antenna systems
General-purpose software radios
Ultrasound equipment
Broadband data applications
GENERAL DESCRIPTION
The AD9634 is a 12-bit, analog-to-digital converter (ADC) with
sampling speeds of up to 250 MSPS. The AD9634 is designed to
support communications applications where low cost, small size,
wide bandwidth, and versatility are desired.
Programming for setup and control is accomplished using a
3-wire, SPI-compatible serial interface.
The AD9634 is available in a 32-lead LFCSP and is specified over
the industrial temperature range of −40°C to +85°C. This product
is protected by a U.S. patent.
The ADC core features a multistage, differential pipelined
architecture with integrated output error correction logic. The
ADC features wide bandwidth inputs that can support a variety
of user-selectable input ranges. An integrated voltage reference
eases design considerations. A duty cycle stabilizer (DCS) is
provided to compensate for variations in the ADC clock duty cycle,
allowing the converter to maintain excellent performance.
PRODUCT HIGHLIGHTS
1. Integrated 12-bit, 170 MSPS/210 MSPS/250 MSPS ADC.
2. Fast overrange and threshold detect.
3. Proprietary differential input maintains excellent SNR
performance for input frequencies of up to 350 MHz.
4. 3-pin, 1.8 V SPI port for register programming and readback.
5. Pin compatibility with the AD9642, allowing a simple
migration up to 14 bits, and with the AD6672.
The ADC output data are routed directly to the external 12-bit
LVDS output port.
Flexible power-down options allow significant power savings,
when desired.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2011 Analog Devices, Inc. All rights reserved.
AD9634
TABLE OF CONTENTS
Features .............................................................................................. 1
ADC Architecture ...................................................................... 19
Analog Input Considerations ................................................... 19
Voltage Reference ....................................................................... 21
Clock Input Considerations...................................................... 21
Power Dissipation and Standby Mode .................................... 23
Digital Outputs ........................................................................... 23
ADC Overrange (OR)................................................................ 23
Serial Port Interface (SPI).............................................................. 24
Configuration Using the SPI..................................................... 24
Hardware Interface..................................................................... 24
SPI Accessible Features.............................................................. 25
Memory Map .................................................................................. 26
Reading the Memory Map Register Table............................... 26
Memory Map Register Table..................................................... 27
Applications Information.............................................................. 29
Design Guidelines ...................................................................... 29
Outline Dimensions....................................................................... 30
Ordering Guide .......................................................................... 30
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description......................................................................... 1
Product Highlights ........................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
ADC DC Specifications................................................................. 3
ADC AC Specifications ................................................................. 4
Digital Specifications ................................................................... 6
Switching Specifications ................................................................ 7
Timing Specifications .................................................................. 8
Absolute Maximum Ratings............................................................ 9
Thermal Characteristics .............................................................. 9
ESD Caution.................................................................................. 9
Pin Configuration and Function Descriptions........................... 10
Typical Performance Characteristics ........................................... 12
Equivalent Circuits......................................................................... 18
Theory of Operation ...................................................................... 19
REVISION HISTORY
7/11—Revision 0: Initial Version
Rev. 0 | Page 2 of 32
AD9634
SPECIFICATIONS
ADC DC SPECIFICATIONS
AVDD = 1.8 V, DRVDD = 1.8 V, maximum sample rate, VIN = −1.0 dBFS differential input, 1.75 V p-p full scale input range,
DCS enabled, unless otherwise noted.
Table 1.
AD9634-170
AD9634-210
AD9634-250
Min Typ Max
Parameter
Temperature
Min
Typ
Max
Min
Typ
Max
Unit
RESOLUTION
Full
12
12
12
Bits
ACCURACY
No Missing Codes
Offset Error
Gain Error
Full
Full
Full
Full
25°C
Full
25°C
Guaranteed
Guaranteed
Guaranteed
11
+2/−11
0.ꢀ
11
11
mV
+1/−8
0.ꢀ
+3/−7 %FSR
Differential Nonlinearity (DNL)
0.ꢀ
0.ꢁ
LSB
LSB
LSB
LSB
0.22
0.2
0.22
0.2
0.22
0.27
Integral Nonlinearity (INL)1
0.ꢀ
0.ꢀ
TEMPERATURE DRIFT
Offset Error
Gain Error
Full
Full
7
55
7
58
7
75
ppm/°C
ppm/°C
INPUT REFERRED NOISE
VREF = 1.0 V
25°C
0.531
0.391
0.ꢀ07
LSB rms
ANALOG INPUT
Input Span
Full
Full
Full
Full
1.75
2.5
20
1.75
2.5
20
1.75
2.5
20
V p-p
pF
kΩ
V
Input Capacitance2
Input Resistance3
Input Common-Mode Voltage
POWER SUPPLIES
Supply Voltage
AVDD
0.9
0.9
0.9
Full
Full
1.7
1.7
1.8
1.8
1.9
1.9
1.7
1.7
1.8
1.8
1.9
1.9
1.7
1.7
1.8
1.8
1.9
1.9
V
V
DRVDD
Supply Current
1
IAVDD
Full
Full
123
50
13ꢀ
5ꢀ
129
5ꢁ
139
ꢁ0
13ꢁ
ꢁꢀ
1ꢀ5
ꢁ8
mA
mA
1
IDRVDD
POWER CONSUMPTION
Sine Wave Input (DRVDD = 1.8 V) Full
311
50
5
3ꢀ0
333
50
5
3ꢁ0
3ꢁ0
50
5
385
mW
mW
mW
Standby Powerꢀ
Full
Full
Power-Down Power
1 Measured with a low input frequency, full-scale sine wave.
2 Input capacitance refers to the effective capacitance between one differential input pin and its complement.
3 Input resistance refers to the effective resistance between one differential input pin and its complement.
ꢀ Standby power is measured with a dc input and the CLK pin inactive (that is, set to AVDD or AGND).
Rev. 0 | Page 3 of 32
AD9634
ADC AC SPECIFICATIONS
AVDD = 1.8 V, DRVDD = 1.8 V, maximum sample rate, VIN = −1.0 dBFS differential input, 1.75 V p-p full-scale input range, unless
otherwise noted.
Table 2.
AD9634-170
AD9634-210
AD9634-250
Parameter1
Temperature Min
Typ
Max Min
Typ
Max Min Typ Max Unit
SIGNAL-TO-NOISE RATIO (SNR)
fIN = 30 MHz
fIN = 90 MHz
25°C
25°C
Full
25°C
25°C
Full
70.3
70.1
70.2
70.1
70.1
70.0
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
ꢁ9.1
ꢁ8.8
fIN = 1ꢀ0 MHz
fIN = 185 MHz
ꢁ9.9
ꢁ9.5
70.0
ꢁ9.ꢁ
ꢁ9.9
ꢁ9.7
ꢁ7.8
fIN = 220 MHz
25°C
ꢁ9.2
ꢁ9.2
ꢁ9.3
SIGNAL-TO-NOISE AND DISTORTION (SINAD)
fIN = 30 MHz
fIN = 90 MHz
25°C
25°C
Full
25°C
25°C
Full
ꢁ9.ꢀ
ꢁ9.2
ꢁ9.2
ꢁ9.1
ꢁ9.2
ꢁ9.0
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
ꢁ8.1
ꢁ7.8
fIN = 1ꢀ0 MHz
fIN = 185 MHz
ꢁ8.9
ꢁ8.5
ꢁ9.1
ꢁ8.7
ꢁ9.0
ꢁ8.7
ꢁꢁ.7
fIN = 220 MHz
25°C
ꢁ8.3
ꢁ8.3
ꢁ8.ꢀ
EFFECTIVE NUMBER OF BITS (ENOB)
fIN = 30 MHz
fIN = 90 MHz
fIN = 1ꢀ0 MHz
fIN = 185 MHz
25°C
25°C
25°C
25°C
25°C
11.2
11.2
11.1
11.1
11.0
11.2
11.2
11.2
11.1
11.0
11.2
11.2
11.2
11.1
11.1
Bits
Bits
Bits
Bits
Bits
fIN = 220 MHz
WORST SECOND OR THIRD HARMONIC
fIN = 30 MHz
fIN = 90 MHz
25°C
25°C
Full
25°C
25°C
Full
−9ꢁ
−95
−9ꢁ
−92
−90
−89
dBc
dBc
dBc
dBc
dBc
dBc
dBc
−83
−80
fIN = 1ꢀ0 MHz
fIN = 185 MHz
−97
−8ꢁ
−9ꢀ
−95
−91
−87
−80
fIN = 220 MHz
25°C
−8ꢀ
−8ꢀ
−93
SPURIOUS-FREE DYNAMIC RANGE (SFDR)
fIN = 30 MHz
fIN = 90 MHz
25°C
25°C
Full
25°C
25°C
Full
9ꢁ
95
9ꢁ
92
90
89
dBc
dBc
dBc
dBc
dBc
dBc
dBc
83
80
fIN = 1ꢀ0 MHz
fIN = 185 MHz
97
8ꢁ
9ꢀ
95
91
87
80
fIN = 220 MHz
25°C
8ꢀ
8ꢀ
93
WORST OTHER (HARMONIC OR SPUR)
fIN = 30 MHz
fIN = 90 MHz
25°C
25°C
Full
25°C
25°C
Full
−98
−97
−9ꢁ
−95
−95
−95
dBc
dBc
dBc
dBc
dBc
dBc
dBc
−87
−83
fIN = 1ꢀ0 MHz
fIN = 185 MHz
−98
−95
−97
−95
−9ꢁ
−9ꢀ
−81
fIN = 220 MHz
25°C
−9ꢁ
−95
−9ꢀ
Rev. 0 | Page ꢀ of 32
AD9634
AD9634-170
AD9634-210
AD9634-250
Parameter1
Temperature Min
Typ
Max Min
Typ
Max Min Typ
Max Unit
TWO-TONE SFDR
fIN = 18ꢀ.1 MHz, 187.1 MHz (−7 dBFS)
FULL POWER BANDWIDTH2
NOISE BANDWIDTH3
25°C
25°C
25°C
87
89
88
dBc
350
1000
350
1000
350
1000
MHz
MHz
1 See the AN-835 Application Note, Understanding High Speed ADC Testing and Evaluation, for a complete set of definitions.
2 Full power bandwidth is the bandwidth of operation where typical ADC performance can be achieved.
3 Noise bandwidth is the −3 dB bandwidth for the ADC inputs across which noise may enter the ADC and is not attenuated internally.
Rev. 0 | Page 5 of 32
AD9634
DIGITAL SPECIFICATIONS
AVDD = 1.8 V, DRVDD = 1.8 V, maximum sample rate, VIN = −1.0 dBFS differential input, 1.0 V internal reference, DCS enabled, unless
otherwise noted.
Table 3.
Parameter
Temperature
Min
Typ
Max
Unit
DIFFERENTIAL CLOCK INPUTS (CLK+, CLK−)
Logic Compliance
CMOS/LVDS/LVPECL
Internal Common-Mode Bias
Differential Input Voltage
Input Voltage Range
Full
Full
Full
Full
Full
Full
Full
Full
0.9
3.ꢁ
V
V p-p
V
0.3
AGND
0.9
10
−22
AVDD
1.ꢀ
22
Input Common-Mode Range
V
High Level Input Current
Low Level Input Current
Input Capacitance
μA
μA
pF
kΩ
−10
ꢀ
Input Resistance
12
15
18
LOGIC INPUT (CSB)1
High Level Input Voltage
Low Level Input Voltage
High Level Input Current
Low Level Input Current
Input Resistance
Full
Full
Full
Full
Full
Full
1.22
0
50
−5
2.1
0.ꢁ
71
V
V
μA
μA
kΩ
pF
+5
2ꢁ
2
Input Capacitance
LOGIC INPUT (SCLK)2
High Level Input Voltage
Low Level Input Voltage
High Level Input Current
Low Level Input Current
Input Resistance
Full
Full
Full
Full
Full
Full
1.22
0
ꢀ5
−5
2.1
0.ꢁ
70
V
V
μA
μA
kΩ
pF
+5
2ꢁ
2
Input Capacitance
LOGIC INPUTS (SDIO)1
High Level Input Voltage
Low Level Input Voltage
High Level Input Current
Low Level Input Current
Input Resistance
Full
Full
Full
Full
Full
Full
1.22
0
ꢀ5
−5
2.1
0.ꢁ
70
V
V
μA
μA
kΩ
pF
+5
2ꢁ
5
Input Capacitance
DIGITAL OUTPUTS
LVDS Data and OR Outputs (OR+, OR−)
Differential Output Voltage (VOD), ANSI Mode
Output Offset Voltage (VOS), ANSI Mode
Differential Output Voltage (VOD), Reduced Swing Mode
Output Offset Voltage (VOS), Reduced Swing Mode
Full
Full
Full
Full
250
1.15
150
1.15
350
1.25
200
1.25
ꢀ50
1.35
280
1.35
mV
V
mV
V
1 Pull-up.
2 Pull-down.
Rev. 0 | Page ꢁ of 32
AD9634
SWITCHING SPECIFICATIONS
Table 4.
AD9634-170
AD9634-210
AD9634-250
Parameter
CLOCK INPUT PARAMETERS1
Temperature
Min
Typ Max Min Typ Max Min Typ Max Unit
Input Clock Rate
Conversion Rate2
Full
ꢁ25
ꢁ25
ꢁ25
MHz
DCS Enabled
DCS Disabled
CLK Period, Divide-by-1 Mode (tCLK
CLK Pulse Width High (tCH)
Full
Full
Full
ꢀ0
10
5.8
170
170
ꢀ0
10
ꢀ.8
210
210
ꢀ0
10
ꢀ
250
250
MSPS
MSPS
ns
)
Divide-by-1 Mode, DCS Enabled
Divide-by-1 Mode, DCS Disabled
Divide-by-2 Mode Through
Divide-by-8 Mode
Full
Full
Full
2.ꢁ1 2.9
2.7ꢁ 2.9
0.8
3.19
3.05
2.1ꢁ 2.ꢀ
2.28 2.ꢀ
0.8
2.ꢁꢀ
2.52
1.8
1.9
0.8
2.0
2.0
2.2
2.1
ns
ns
ns
Aperture Delay (tA)
Full
Full
1.0
0.1
1.0
0.1
1.0
0.1
ns
ps rms
Aperture Uncertainty (Jitter, tJ)
DATA OUTPUT PARAMETERS1
Data Propagation Delay (tPD)
DCO Propagation Delay (tDCO
DCO to Data Skew (tSKEW
Pipeline Delay (Latency)
Wake-Up Time (from Standby)
Wake-Up Time (from Power-Down)
Out-of-Range Recovery Time
Full
Full
Full
Full
Full
Full
Full
ꢀ.1
ꢀ.7
0.3
ꢀ.7
5.3
0.5
10
10
100
3
5.2
5.8
0.7
ꢀ.1
ꢀ.7
0.3
ꢀ.7
5.3
0.5
10
10
100
3
5.2
5.8
0.7
ꢀ.1
ꢀ.7
0.3
ꢀ.7
5.3
0.5
10
10
100
3
5.2
5.8
0.7
ns
ns
ns
Cycles
μs
)
)
μs
Cycles
1 See Figure 2.
2 Conversion rate is the clock rate after the divider.
Timing Diagram
N – 1
N + 4
tA
N + 5
N
N + 3
VIN
N + 1
N + 2
tCH
tCLK
CLK+
CLK–
tDCO
DCO–
DCO+
tSKEW
tPD
D0±/D1±
D0
N – 10
D1
N – 10
D0
N – 9
D1
N – 9
D0
N – 8
D1
N – 8
D0
N – 7
D1
N – 7
D0
N – 6
EVEN/ODD
(LSB)
D10±/D11±
(MSB)
D10
N – 10
D11
N – 10
D10
N – 9
D11
N – 9
D10
N – 8
D11
N – 8
D10
N – 7
D11
N – 7
D10
N – 6
Figure 2. Even/Odd LVDS Mode Data Output Timing
Rev. 0 | Page 7 of 32
AD9634
TIMING SPECIFICATIONS
Table 5.
Parameter
Test Conditions/Comments
Min Typ Max Unit
SPI TIMING REQUIREMENTS
tDS
tDH
tCLK
tS
See Figure 58 for the SPI timing diagram
Setup time between the data and the rising edge of SCLK
Hold time between the data and the rising edge of SCLK
Period of the SCLK
2
2
ꢀ0
2
2
10
10
10
ns
ns
ns
ns
ns
ns
ns
ns
Setup time between CSB and SCLK
tH
Hold time between CSB and SCLK
tHIGH
tLOW
tEN_SDIO
Minimum period that SCLK should be in a logic high state
Minimum period that SCLK should be in a logic low state
Time required for the SDIO pin to switch from an input to an output
relative to the SCLK falling edge (not shown in Figure 58)
tDIS_SDIO
Time required for the SDIO pin to switch from an output to an input
relative to the SCLK rising edge (not shown in Figure 58)
10
ns
Rev. 0 | Page 8 of 32
AD9634
ABSOLUTE MAXIMUM RATINGS
THERMAL CHARACTERISTICS
Table 6.
The exposed paddle must be soldered to the ground plane for the
LFCSP package. Soldering the exposed paddle to the customer
board increases the reliability of the solder joints, maximizing
the thermal capability of the package.
Parameter
Rating
Electrical
AVDD to AGND
DRVDD to AGND
VIN+, VIN− to AGND
CLK+, CLK− to AGND
VCM to AGND
CSB to AGND
SCLK to AGND
SDIO to AGND
D0 /D1 through D10 /D11
to AGND
−0.3 V to +2.0 V
−0.3 V to +2.0 V
−0.3 V to AVDD + 0.2 V
−0.3 V to AVDD + 0.2V
−0.3 V to AVDD + 0.2 V
−0.3 V to DRVDD + 0.3 V
−0.3 V to DRVDD + 0.3 V
−0.3 V to DRVDD + 0.3 V
−0.3 V to DRVDD + 0.3 V
Table 7. Thermal Resistance
Airflow
Velocity
(m/sec)
Package
Type
1, 2
1, 3
1, 4
θJA
θJC
3.1
θJB
20.7
Unit
°C/W
°C/W
°C/W
32-Lead LFCSP
5 mm × 5 mm
(CP-32-12)
0
37.1
32.ꢀ
29.1
1.0
2.0
1 Per JEDEC 51-7, plus JEDEC 25-5 2S2P test board.
DCO+/DCO− to AGND
OR+/OR− to AGND
Environmental
−0.3 V to DRVDD + 0.3 V
−0.3 V to DRVDD + 0.3 V
2 Per JEDEC JESD51-2 (still air) or JEDEC JESD51-ꢁ (moving air).
3 Per MIL-Std 883, Method 1012.1.
ꢀ Per JEDEC JESD51-8 (still air).
Operating Temperature Range
(Ambient)
Maximum Junction Temperature
Under Bias
Storage Temperature Range
(Ambient)
−ꢀ0°C to +85°C
150°C
Typical θJA is specified for a 4-layer PCB with solid ground plane.
As shown in Table 7, airflow increases heat dissipation, which
reduces θJA. In addition, metal in direct contact with the package
leads from metal traces, through holes, ground, and power
planes reduces the θJA.
−ꢁ5°C to +125°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
Rev. 0 | Page 9 of 32
AD9634
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
CLK+ 1
24 CSB
23
2
CLK–
SCLK
AVDD 3
OR– 4
22 SDIO
21 DCO+
AD9634
TOP VIEW
5
6
20
19
OR+
D0–/D1– (LSB)
DCO–
D10+/D11+ (MSB)
(Not to Scale)
D0+/D1+ (LSB) 7
DRVDD 8
18 D10–/D11– (MSB)
17 DRVDD
NOTES
1. DNC = DO NOT CONNECT. DO NOT CONNECT TO THIS PIN.
2. THE EXPOSED THERMAL PADDLE ON THE BOTTOM OF THE PACKAGE
PROVIDES THE ANALOG GROUND FOR THE PART. THIS EXPOSED
PADDLE MUST BE CONNECTED TO GROUND FOR PROPER OPERATION.
Figure 3. Pin Configuration
Table 8. Pin Function Descriptions
Pin No.
Mnemonic
Type
Description
ADC Power Supplies
8, 17
DRVDD
AVDD
Supply
Supply
Ground
Digital Output Driver Supply (1.8 V Nominal).
Analog Power Supply (1.8 V Nominal).
3, 27, 28, 31, 32
0
AGND, Exposed
Paddle
Analog Ground. The exposed thermal paddle on the bottom of the
package provides the analog ground for the part. This exposed paddle
must be connected to ground for proper operation.
25
DNC
Do No Connect. Do not connect to this pin.
ADC Analog
30
29
2ꢁ
VIN+
VIN−
VCM
Input
Input
Output
Differential Analog Input Pin (+).
Differential Analog Input Pin (−).
Common-Mode Level Bias Output for Analog Inputs. This pin should be
decoupled to ground using a 0.1 μF capacitor.
1
2
CLK+
CLK−
Input
Input
ADC Clock Input—True.
ADC Clock Input—Complement.
Digital Outputs
5
ꢀ
7
ꢁ
10
9
12
11
1ꢀ
13
1ꢁ
15
19
18
21
20
OR+
OR−
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Overrange—True.
Overrange—Complement.
D0+/D1+ (LSB)
D0−/D1− (LSB)
D2+/D3+
D2−/D3−
Dꢀ+/D5+
Dꢀ−/D5−
Dꢁ+/D7+
Dꢁ−/D7−
D8+/D9+
D8−/D9−
D10+/D11+ (MSB)
D10−/ D11− (MSB)
DCO+
DDR LVDS Output Data 0/Data 1—True (LSB).
DDR LVDS Output Data 0/Data 1—Complement (LSB).
DDR LVDS Output Data 2/Data 3—True.
DDR LVDS Output Data 2/Data 3—Complement.
DDR LVDS Output Data ꢀ/Data 5—True.
DDR LVDS Output Data ꢀ/Data 5—Complement.
DDR LVDS Output Data ꢁ/Data 7—True.
DDR LVDS Output Data ꢁ/Data 7—Complement.
DDR LVDS Output Data 8/Data 9—True.
DDR LVDS Output Data 8/Data 9—Complement.
DDR LVDS Output Data 10/Data 11—True (MSB).
DDR LVDS Output Data 10/Data 11—Complement (MSB).
LVDS Data Clock Output—True.
DCO−
LVDS Data Clock Output—Complement.
Rev. 0 | Page 10 of 32
AD9634
Pin No.
Mnemonic
Type
Description
SPI Control
23
22
2ꢀ
SCLK
SDIO
CSB
Input
Input/Output
Input
SPI Serial Clock.
SPI Serial Data I/O.
SPI Chip Select (Active Low).
Rev. 0 | Page 11 of 32
AD9634
TYPICAL PERFORMANCE CHARACTERISTICS
AVDD = 1.8 V, DRVDD = 1.8 V, sample rate = maximum sample rate per speed grade, DCS enabled, 1.75 V p-p differential input,
VIN = −1.0 dBFS, 32k sample, TA = 25°C, unless otherwise noted.
0
–20
0
170MSPS
170MSPS
305.1MHz @ –1.0dBFS
SNR = 67.2dB (68.2dBFS)
SFDR = 86dBc
90.1MHz @ –1.0dBFS
SNR = 69.1dB (70.1dBFS)
SFDR = 93dBc
–20
–40
–40
–60
–60
SECOND
HARMONIC
THIRD
HARMONIC
THIRD
HARMONIC
SECOND
HARMONIC
–80
–80
–100
–120
–140
–100
–120
–140
0
10
20
30
40
50
60
70
80
0
10
20
30
40
50
60
70
80
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 4. AD9634-170 Single-Tone FFT with fIN = 90.1 MHz
Figure 7. AD9634-170 Single-Tone FFT with fIN = 305.1 MHz
0
120
170MSPS
185.1MHz @ –1.0dBFS
SNR = 68.5dB (69.5dBFS)
SFDR (dBFS)
–20
100
80
60
40
20
0
SFDR = 86dBc
–40
–60
SNR (dBFS)
THIRD
HARMONIC
SECOND
HARMONIC
–80
SFDR (dBc)
–100
–120
–140
SNR (dBc)
–100 –90 –80 –70 –60 –50 –40 –30 –20 –10
0
0
10
20
30
40
50
60
70
80
INPUT AMPLITUDE (dBFS)
FREQUENCY (MHz)
Figure 8. AD9634-170 Single-Tone SNR/SFDR vs.
Input Amplitude (AIN) with fIN = 90.1 MHz, fS = 170 MSPS
Figure 5. AD9634-170 Single-Tone FFT with fIN = 185.1 MHz
100
0
170MSPS
220.1MHz @ –1.0dBFS
SNR = 68.2dB (69.2dBFS)
SFDR = 84dBc
95
90
85
80
75
70
65
60
–20
SFDR (dBc)
–40
–60
THIRD
HARMONIC
SECOND
HARMONIC
–80
–100
–120
–140
SNR (dBFS)
60
90
120 150 180 210 240 270 300 330
INPUT FREQUENCY (MHz)
0
10
20
30
40
50
60
70
80
FREQUENCY (MHz)
Figure 9. AD9634-170 Single-Tone SNR/SFDR vs. Input Frequency (fIN),
fS = 170 MSPS
Figure 6. AD9634-170 Single-Tone FFT with fIN = 220.1 MHz
Rev. 0 | Page 12 of 32
AD9634
0
–20
0
–20
170MSPS
184.12MHz @ –7.0dBFS
187.12MHz @ –7.0dBFS
SFDR = 85dBc (92dBFS)
SFDR (dBc)
–40
–40
IMD3 (dBc)
–60
–60
–80
–80
–100
–120
–140
SFDR (dBFS)
IMD3 (dBFS)
–100
–120
–90.0 –81.7 –73.4 –65.1 –56.8 –48.5 –40.2 –31.9 –23.6 –15.3 –7.0
INPUT AMPLITUDE (dBFS)
0
10
20
30
40
50
60
70
80
FREQUENCY (MHz)
Figure 10. AD9634-170 Two-Tone SFDR/IMD3 vs. Input Amplitude (AIN) with
fIN1 = 89.12 MHz, fIN2 = 92.12 MHz, fS = 170 MSPS
Figure 13. AD9634-170 Two Tone FFT with fIN1 = 184.12 MHz, fIN2 = 187.12 MHz
0
100
SFDR
95
–20
SFDR (dBc)
90
85
80
75
–40
IMD3 (dBc)
–60
–80
SFDR (dBFS)
–100
SNR
70
IMD3 (dBFS)
–120
65
–90.0 –81.7 –73.4 –65.1 –56.8 –48.5 –40.2 –31.9 –23.6 –15.3 –7.0
40 50 60 70 80 90 100 110 120 130 140 150 160 170
INPUT AMPLITUDE (dBFS)
SAMPLE RATE (MSPS)
Figure 11. AD9634-170 Two-Tone SFDR/IMD3 vs. Input Amplitude (AIN
)
Figure 14. AD9634-170 Single-Tone SNR/SFDR vs. Sample Rate (fS)
with fIN = 90 MHz
with fIN1 = 184.12 MHz, fIN2 = 187.12 MHz, fS = 170 MSPS
0
14000
170MSPS
0.531 LSB rms
16,384 TOTAL HITS
89.12MHz @ –7.0dBFS
92.12MHz @ –7.0dBFS
SFDR = 89dBc (96dBFS)
–20
–40
12000
10000
8000
6000
4000
2000
0
–60
–80
–100
–120
–140
0
10
20
30
40
50
60
70
80
N – 1
N
N + 1
FREQUENCY (MHz)
OUTPUT CODE
Figure 12. AD9634-170 Two-Tone FFT with fIN1 = 89.12 MHz, fIN2 = 92.12 MHz
Figure 15. AD9634-170 Grounded Input Histogram, fS = 170 MSPS
Rev. 0 | Page 13 of 32
AD9634
0
0
–20
210MSPS
210MSPS
90.1MHz @ –1.0dBFS
SNR = 69.1dB (70.1dBFS)
SFDR = 92dBc
305.1MHz @ –1.0dBFS
SNR = 67.6dB (68.6dBFS)
SFDR = 83dBc
–20
–40
–40
–60
–60
SECOND
HARMONIC
THIRD
HARMONIC
SECOND
HARMONIC
THIRD
HARMONIC
–80
–80
–100
–120
–140
–100
–120
–140
0
15
30
45
60
75
90
105
0
15
30
45
60
75
90
105
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 16. AD9634-210 Single-Tone FFT with fIN = 90.1 MHz
Figure 19. AD9634-210 Single-Tone FFT with fIN = 305.1 MHz
0
120
210MSPS
185.1MHz @ –1.0dBFS
SNR = 68.6dB (69.6dBFS)
SFDR = 93dBc
SFDR (dBFS)
–20
100
–40
–60
80
SNR (dBFS)
SECOND
HARMONIC
THIRD
HARMONIC
60
–80
SFDR (dBc)
40
–100
–120
–140
SNR (dBc)
20
0
–100 –90 –80 –70 –60 –50 –40 –30 –20 –10
0
0
15
30
45
60
75
90
105
INPUT AMPLITUDE (dBFS)
FREQUENCY (MHz)
Figure 20. AD9634-210 Single-Tone SNR/SFDR vs. Input Amplitude (AIN) with
fIN = 90.1 MHz, fS = 210 MSPS
Figure 17. AD9634-210 Single-Tone FFT with fIN = 185.1 MHz
100
0
210MSPS
SFDR (dBc)
220.1MHz @ –1.0dBFS
95
90
85
80
75
SNR = 68.3dB (69.3dBFS)
SFDR = 84dBc
–20
–40
–60
SECOND
HARMONIC
THIRD
HARMONIC
–80
–100
–120
–140
SNR (dBFS)
70
65
60
60
90
120 150 180 210 240 270 300 330
INPUT FREQUENCY (MHz)
0
15
30
45
60
75
90
105
FREQUENCY (MHz)
Figure 21. AD9634-210 Single-Tone SNR/SFDR vs. Input Frequency (fIN),
fS = 210 MSPS
Figure 18. AD9634-210 Single-Tone FFT with fIN = 220.1 MHz
Rev. 0 | Page 1ꢀ of 32
AD9634
0
–20
0
–20
210MSPS
184.12MHz @ –7.0dBFS
187.12MHz @ –7.0dBFS
SFDR = 89dBc (96dBFS)
SFDR (dBc)
–40
–40
IMD3 (dBc)
–60
–60
–80
–80
–100
–120
–140
SFDR (dBFS)
IMD3 (dBFS)
–100
–120
–90.0 –81.7 –73.4 –65.1 –56.8 –48.5 –40.2 –31.9 –23.6 –15.3 –7.0
INPUT AMPLITUDE (dBFS)
0
15
30
45
60
75
90
105
FREQUENCY (MHz)
Figure 22. AD9634-210 Two-Tone SFDR/IMD3 vs. Input Amplitude (AIN) with
fIN1 = 89.12 MHz, fIN2 = 92.12 MHz, fS = 210 MSPS
Figure 25. AD9634-210 Two Tone FFT with fIN1 = 184.12 MHz, fIN2 = 187.12 MHz
0
100
SFDR
95
90
85
80
75
–20
SFDR (dBc)
–40
IMD3 (dBc)
–60
–80
SFDR (dBFS)
–100
SNR
70
IMD3 (dBFS)
–120
65
–90.0 –81.7 –73.4 –65.1 –56.8 –48.5 –40.2 –31.9 –23.6 –15.3 –7.0
40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210
INPUT AMPLITUDE (dBFS)
SAMPLE RATE (MSPS)
Figure 23. AD9634-210 Two-Tone SFDR/IMD3 vs. Input Amplitude (AIN) with
fIN1 = 184.12 MHz, fIN2 = 187.12 MHz, fS = 210 MSPS
Figure 26. AD9634-210 Single-Tone SNR/SFDR vs. Sample Rate (fS) with
fIN = 90 MHz
0
16000
210MSPS
0.391 LSB rms
16,384 TOTAL HITS
89.12MHz @ –7.0dBFS
92.12MHz @ –7.0dBFS
14000
–20
SFDR = 88dBc (95dBFS)
–40
12000
10000
8000
6000
4000
2000
0
–60
–80
–100
–120
–140
0
15
30
45
60
75
90
105
N – 1
N
N + 1
FREQUENCY (MHz)
OUTPUT CODE
Figure 24. AD9634-210 Two-Tone FFT with fIN1 = 89.12 MHz, fIN2 = 92.12 MHz
Figure 27. AD9634-210 Grounded Input Histogram, fS = 210 MSPS
Rev. 0 | Page 15 of 32
AD9634
0
0
–20
250MSPS
250MSPS
90.1MHz @ –1.0dBFS
SNR = 69.0dB (70.0dBFS)
SFDR = 89dBc
305.1MHz @ –1.0dBFS
SNR = 67.4dB (68.4dBFS)
SFDR = 82dBc
–20
–40
–40
–60
–60
SECOND
THIRD
SECOND
HARMONIC
THIRD
HARMONIC
HARMONIC
HARMONIC
–80
–80
–100
–120
–140
–100
–120
–140
0
25
50
75
100
125
0
25
50
75
100
125
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 28. AD9634-250 Single-Tone FFT with fIN = 90.1 MHz
Figure 31. AD9634-250 Single-Tone FFT with fIN = 305.1 MHz
0
120
250MSPS
185.1MHz @ –1.0dBFS
SFDR (dBFS)
SNR = 68.7dB (69.7dBFS)
SFDR = 87dBc
–20
–40
100
80
SNR (dBFS)
–60
THIRD
HARMONIC
SECOND
HARMONIC
60
–80
SFDR (dBc)
40
–100
–120
–140
SNR (dBc)
20
0
–100 –90 –80 –70 –60 –50 –40 –30 –20 –10
0
0
25
50
75
100
125
INPUT AMPLITUDE (dBFS)
FREQUENCY (MHz)
Figure 32. AD9634-250 Single-Tone SNR/SFDR vs. Input Amplitude (AIN) with
fIN = 90.1 MHz, fS = 250 MSPS
Figure 29. AD9634-250 Single-Tone FFT with fIN = 185.1 MHz
100
0
250MSPS
220.1MHz @ –1.0dBFS
SNR = 68.3dB (69.3dBFS)
SFDR = 91dBc
95
–20
–40
SFDR (dBc)
90
85
80
75
70
–60
SECOND
HARMONIC
THIRD
HARMONIC
–80
–100
–120
–140
SNR (dBFS)
65
60
60
90
120 150 180 210 240 270 300 330
INPUT FREQUENCY (MHz)
0
25
50
75
100
125
FREQUENCY (MHz)
Figure 33. AD9634-250 Single-Tone SNR/SFDR vs. Input Frequency (fIN),
fS = 250 MSPS
Figure 30. AD9634-250 Single-Tone FFT with fIN = 220.1 MHz
Rev. 0 | Page 1ꢁ of 32
AD9634
0
–20
0
–20
250MSPS
184.12MHz @ –7.0dBFS
187.12MHz @ –7.0dBFS
SFDR = 88dBc (95dBFS)
SFDR (dBc)
–40
–40
IMD3 (dBc)
–60
–60
–80
–80
–100
–120
–140
SFDR (dBFS)
IMD3 (dBFS)
–100
–120
–90.0 –81.7 –73.4 –65.1 –56.8 –48.5 –40.2 –31.9 –23.6 –15.3 –7.0
INPUT AMPLITUDE (dBFS)
0
25
50
75
100
125
FREQUENCY (MHz)
Figure 34. AD9634-250 Two-Tone SFDR/IMD3 vs. Input Amplitude (AIN) with
fIN1 = 89.12 MHz, fIN2 = 92.12 MHz, fS = 250 MSPS
Figure 37. AD9634-250 Two Tone FFT with fIN1 = 184.12 MHz, fIN2 = 187.12 MHz
0
100
SFDR
95
–20
SFDR (dBc)
90
85
80
75
–40
IMD3 (dBc)
–60
–80
SFDR (dBFS)
SNR
–100
70
IMD3 (dBFS)
–120
65
–90.0 –81.7 –73.4 –65.1 –56.8 –48.5 –40.2 –31.9 –23.6 –15.3 –7.0
40
60
80 100 120 140 160 180 200 220 240 260
SAMPLE RATE (MSPS)
INPUT AMPLITUDE (dBFS)
Figure 35. AD9634-250 Two-Tone SFDR/IMD3 vs. Input Amplitude (AIN
)
Figure 38. AD9634-250 Single-Tone SNR/SFDR vs. Sample Rate (fS)
with fIN = 90 MHz
with fIN1 = 184.12 MHz, fIN2 = 187.12 MHz, fS = 250 MSPS
0
16000
250MSPS
0.407 LSB rms
16,384 TOTAL HITS
89.12MHz @ –7.0dBFS
92.12MHz @ –7.0dBFS
SFDR = 88dBc (95dBFS)
14000
–20
–40
12000
10000
8000
6000
4000
2000
0
–60
–80
–100
–120
–140
0
25
50
75
100
125
N – 1
N
N + 1
FREQUENCY (MHz)
OUTPUT CODE
Figure 36. AD9634-250 Two-Tone FFT with fIN1 = 89.12 MHz, fIN2 = 92.12 MHz
Figure 39. AD9634-250 Grounded Input Histogram, fS = 250 MSPS
Rev. 0 | Page 17 of 32
AD9634
EQUIVALENT CIRCUITS
DRVDD
AVDD
VIN
350Ω
SDIO
26kΩ
Figure 43. Equivalent SDIO Circuit
Figure 40. Equivalent Analog Input Circuit
AVDD
AVDD
AVDD
0.9V
350Ω
26kΩ
SCLK
15kΩ
15kΩ
CLK+
CLK–
Figure 44. Equivalent SCLK Input Circuit
Figure 41. Equivalent Clock lnput Circuit
DRVDD
AVDD
26kΩ
350Ω
CSB
V+
DATAOUT–
V–
V–
DATAOUT+
V+
Figure 45. Equivalent CSB Input Circuit
Figure 42. Equivalent LVDS Output Circuit
Rev. 0 | Page 18 of 32
AD9634
THEORY OF OPERATION
In intermediate frequency (IF) undersampling applications, reduce
the shunt capacitors. In combination with the driving source
impedance, the shunt capacitors limit the input bandwidth.
Refer to the AN-742 Application Note, Frequency Domain
Response of Switched-Capacitor ADCs; the AN-827 Application
Note, A Resonant Approach to Interfacing Amplifiers to Switched-
Capacitor ADCs; and the Analog Dialogue article, “Transformer-
Coupled Front-End for Wideband A/D Converters” for more
information on this subject.
The AD9634 can sample any fS/2 frequency segment from dc to
250 MHz using appropriate low-pass or band-pass filtering at
the ADC inputs with little loss in ADC performance.
Programming and control of the AD9634 are accomplished
using a 3-pin, SPI-compatible serial interface.
ADC ARCHITECTURE
The AD9634 architecture consists of a front-end sample-and-
hold circuit, followed by a pipelined, switched-capacitor ADC.
The quantized outputs from each stage are combined into a
final 12-bit result in the digital correction logic. The pipelined
architecture permits the first stage to operate on a new input
sample and the remaining stages to operate on the preceding
samples. Sampling occurs on the rising edge of the clock.
BIAS
S
S
C
C
FB
S
VIN+
VIN–
C
C
PAR1
PAR2
S
H
S
S
Each stage of the pipeline, excluding the last, consists of a low
resolution flash ADC connected to a switched-capacitor digital-
to-analog converter (DAC) and an interstage residue amplifier
(MDAC). The MDAC magnifies the difference between the
reconstructed DAC output and the flash input for the next stage
in the pipeline. One bit of redundancy is used in each stage to
facilitate digital correction of flash errors. The last stage simply
consists of a flash ADC.
C
S
C
C
FB
C
PAR1
PAR2
S
BIAS
Figure 46. Switched-Capacitor Input
For best dynamic performance, match the source impedances
driving VIN+ and VIN− and differentially balance the inputs.
The input stage contains a differential sampling circuit that can
be ac- or dc-coupled in differential or single-ended modes. The
output staging block aligns the data, corrects errors, and passes the
data to the output buffers. The output buffers are powered from a
separate supply, allowing digital output noise to be separated from
the analog core. During power-down, the output buffers go into
a high impedance state.
Input Common Mode
The analog inputs of the AD9634 are not internally dc biased. In
ac-coupled applications, the user must provide this bias externally.
Setting the device so that VCM = 0.5 × AVDD (or 0.9 V) is
recommended for optimum performance. An on-board common-
mode voltage reference is included in the design and is available
from the VCM pin. Using the VCM output to set the input
common mode is recommended. Optimum performance is
achieved when the common-mode voltage of the analog input
is set by the VCM pin voltage (typically 0.5 × AVDD). The
VCM pin must be decoupled to ground by a 0.1 μF capacitor,
as described in the Applications Information section. Place this
decoupling capacitor close to the pin to minimize the series
resistance and inductance between the part and this capacitor.
ANALOG INPUT CONSIDERATIONS
The analog input to the AD9634 is a differential switched-capacitor
circuit that has been designed to attain optimum performance
when processing a differential input signal.
The clock signal alternatively switches the input between sample
mode and hold mode (see the configuration shown in Figure 46).
When the input is switched into sample mode, the signal source
must be capable of charging the sampling capacitors and settling
within ½ clock cycle.
A small resistor in series with each input can help reduce the
peak transient current required from the output stage of the
driving source. A shunt capacitor can be placed across the
inputs to provide dynamic charging currents. This passive
network creates a low-pass filter at the ADC input; therefore,
the precise values are dependent on the application.
Rev. 0 | Page 19 of 32
AD9634
Differential Input Configurations
C2
R3
Optimum performance can be achieved when driving the
AD9634 in a differential input configuration. For baseband
applications, the AD8138, ADA4937-1, and ADA4930-1
differential drivers provide excellent performance and a flexible
interface to the ADC.
R2
R2
VIN+
VIN–
R1
C1
R1
2V p-p
49.9Ω
ADC
VCM
The output common-mode voltage of the ADA4930-1 is easily
set with the VCM pin of the AD9634 (see Figure 47), and the
driver can be configured in a Sallen-Key filter topology to
provide band limiting of the input signal.
15pF
0.1µF
R3
0.1µF
C2
Figure 48. Differential Transformer-Coupled Configuration
The signal characteristics must be considered when selecting
a transformer. Most RF transformers saturate at frequencies
below a few megahertz. Excessive signal power can also cause
core saturation, which leads to distortion.
200Ω
33Ω
5pF
15Ω
90Ω
VIN–
VIN+
76.8Ω
AVDD
ADC
VCM
VIN
ADA4930-1
At input frequencies in the second Nyquist zone and above, the
noise performance of most amplifiers is not adequate to achieve
the true SNR performance of the AD9634. For applications where
SNR is a key parameter, differential double balun coupling is
the recommended input configuration (see Figure 49). In this
configuration, the input is ac-coupled and the VCM voltage is
provided to each input through a 33 Ω resistor. These resistors
compensate for losses in the input baluns to provide a 50 Ω
impedance to the driver.
0.1µF
33Ω
15pF
15Ω
120Ω
200Ω
0.1µF
Figure 47. Differential Input Configuration Using the ADA4930-1
For baseband applications where SNR is a key parameter,
differential transformer coupling is the recommended input
configuration. An example is shown in Figure 48. To bias the
analog input, connect the VCM voltage to the center tap of the
secondary winding of the transformer.
In the double balun and transformer configurations, the value
of the input capacitors and resistors is dependent on the input
frequency and source impedance. Based on these parameters
the value of the input resistors and capacitors may need to be
adjusted, or some components may need to be removed. Table 9
displays recommended values to set the RC network for different
input frequency ranges. However, these values are dependent on
the input signal and bandwidth and should be used only as a
starting guide. Note that the values given in Table 9 are for the
R1, R2, R3, C1, and C2 components shown in Figure 49.
Table 9. Example RC Network
Frequency Range (MHz)
R1 Series (Ω)
C1 Differential (pF)
R2 Series (Ω)
C2 Shunt (pF)
R3 Shunt (Ω)
ꢀ9.9
ꢀ9.9
0 to 100
100 to 300
33
15
8.2
3.9
0
0
15
8.2
C2
R3
R1
0.1µF
0.1µF
R2
R2
VIN+
2V p-p
33Ω
P
S
S
P
C1
ADC
A
0.1µF
33Ω
0.1µF
R1
VCM
VIN–
R3
0.1µF
C2
Figure 49. Differential Double Balun Input Configuration
Rev. 0 | Page 20 of 32
AD9634
1000pF 180nH 220nH
1µH
165Ω
VPOS
15pF
VCM
1nF
AD8375
5.1pF 3.9pF
301Ω
2.5kΩ║2pF
165Ω
1nF
1µH
68nH
AD9634
180nH 220nH
1000pF
NOTES
1. ALL INDUCTORS ARE COILCRAFT 0603CS COMPONENTS
WITH THE EXCEPTION OF THE 1µH CHOKE INDUCTORS (0603LS).
2. FILTER VALUES SHOWN ARE FOR A 20MHz BANDWIDTH FILTER CENTERED AT 140MHz.
Figure 50. Differential Input Configuration Using the AD8375
An alternative to using a transformer-coupled input at
frequencies in the second Nyquist zone is to use an amplifier
with variable gain. The AD8375 digital variable gain amplifier
(DVGA) provides good performance for driving the AD9634.
Figure 50 shows an example of the AD8375 driving the AD9634
through a band-pass antialiasing filter.
The RF balun configuration is recommended for clock frequencies
between 125 MHz and 625 MHz, and the RF transformer is
recommended for clock frequencies from 10 MHz to 200 MHz.
The back-to-back Schottky diodes across the secondary windings
of the transformer limit clock excursions into the AD9634 to
approximately 0.8 V p-p differential. This limit helps prevent the
large voltage swings of the clock from feeding through to other
portions of the AD9634, while preserving the fast rise and fall times
of the signal, which are critical for low jitter performance.
VOLTAGE REFERENCE
A stable and accurate voltage reference is built into the AD9634.
The full-scale input range can be adjusted by varying the reference
voltage via SPI. The input span of the ADC tracks reference
voltage changes linearly.
®
Mini-Circuits
ADT1-1WT, 1:1Z
ADC
390pF
390pF
390pF
XFMR
CLOCK
INPUT
CLK+
CLK–
CLOCK INPUT CONSIDERATIONS
100Ω
50Ω
For optimum performance, the AD9634 sample clock inputs,
CLK+ and CLK−, should be clocked with a differential signal.
The signal is typically ac-coupled into the CLK+ and CLK− pins by
means of a transformer or a passive component configuration.
These pins are biased internally (see Figure 51) and require no
external bias. If the inputs are floated, the CLK− pin is pulled low
to prevent spurious clocking.
SCHOTTKY
DIODES:
HSMS2822
Figure 52. Transformer Coupled Differential Clock (Up to 200 MHz)
25Ω
ADC
390pF
1nF
390pF
390pF
AVDD
CLOCK
INPUT
CLK+
0.9V
CLK–
CLK+
CLK–
SCHOTTKY
DIODES:
HSMS2822
25Ω
4pF
4pF
Figure 53. Balun-Coupled Differential Clock (Up to 625 MHz)
If a low jitter clock source is not available, another option is to
ac couple a differential PECL signal to the sample clock input pins
as shown in Figure 54. The AD9510, AD9511,AD9512, AD9513,
AD9514, AD9515, AD9516, AD9517, AD9518, AD9520, AD9522,
AD9523, AD9524, ADCLK905, ADCLK907, and ADCLK925
clock drivers offer excellent jitter performance.
Figure 51. Equivalent Clock Input Circuit
Clock Input Options
The AD9634 has a very flexible clock input structure. Clock input
can be a CMOS, LVDS, LVPECL, or sine wave signal. Regardless
of the type of signal being used, clock source jitter is of the most
concern, as described in the Jitter Considerations section.
0.1µF
0.1µF
Figure 52 and Figure 53 show two preferable methods for clocking
the AD9634 (at clock rates of up to 625 MHz). A low jitter clock
source is converted from a single-ended signal to a differential
signal using an RF balun or RF transformer.
CLOCK
INPUT
CLK+
AD95xx,
100Ω
ADCLKxxx
ADC
CLK–
0.1µF PECL DRIVER
0.1µF
CLOCK
INPUT
240Ω
240Ω
50kΩ
50kΩ
Figure 54. Differential PECL Sample Clock (Up to 625 MHz)
Rev. 0 | Page 21 of 32
AD9634
A third option is to ac couple a differential LVDS signal to the
sample clock input pins, as shown in Figure 55. The AD9510,
AD9511,AD9512, AD9513, AD9514, AD9515, AD9516, AD9517,
AD9518, AD9520, AD9522, AD9523, AD9524 clock drivers offer
excellent jitter performance.
Jitter Considerations
High speed, high resolution ADCs are sensitive to the quality
of the clock input. The degradation in SNR at a given input
frequency (fIN) due to jitter (tJ) can be calculated by
SNRHF = −10 log[(2π × fIN × tJRMS)2 + 10 (−SNR /10)
]
LF
In the equation, the rms aperture jitter represents the root-
mean-square of all jitter sources, which include the clock input,
the analog input signal, and the ADC aperture jitter specification.
IF undersampling applications are particularly sensitive to jitter,
as shown in Figure 56.
0.1µF
0.1µF
CLOCK
INPUT
CLK+
AD95xx
LVDS DRIVER
100Ω
ADC
0.1µF
0.1µF
CLOCK
INPUT
CLK–
50kΩ
50kΩ
80
Figure 55. Differential LVDS Sample Clock (Up to 625 MHz)
75
70
65
60
Input Clock Divider
The AD9634 contains an input clock divider with the ability to
divide the input clock by integer values between 1 and 8. For
divide ratios other than 1, the DCS is enabled by default on
power-up.
Clock Duty Cycle
0.05ps
0.2ps
0.5ps
1ps
1.5ps
Typical high speed ADCs use both clock edges to generate a
variety of internal timing signals and, as a result, may be sensitive to
clock duty cycle. Commonly, a 5% tolerance is required on the
clock duty cycle to maintain dynamic performance characteristics.
55
MEASURED
50
1
10
100
1000
INPUT FREQUENCY (MHz)
The AD9634 contains a DCS that retimes the nonsampling
(falling) edge, providing an internal clock signal with a nominal
50% duty cycle. This allows the user to provide a wide range of
clock input duty cycles without affecting the performance of the
AD9634.
Figure 56. AD9634-250 SNR vs. Input Frequency and Jitter
In cases where aperture jitter may affect the dynamic range of the
AD9634, treat the clock input as an analog signal. In addition,
use separate power supplies for the clock drivers and the ADC
output driver to avoid modulating the clock signal with digital
noise. Low jitter, crystal controlled oscillators provide the best clock
sources. If the clock is generated from another type of source (by
gating, dividing, or another method), it should be retimed by the
original clock during the last step.
Jitter on the rising edge of the input clock is still of paramount
concern and is not reduced by the duty cycle stabilizer. The duty
cycle control loop does not function for clock rates less than
40 MHz nominally. The loop has a time constant associated
with it that must be considered when the clock rate may change
dynamically. A wait time of 1.5 μs to 5 μs is required after a
dynamic clock frequency increase or decrease before the DCS loop
is relocked to the input signal. During the time that the loop is
not locked, the DCS loop is bypassed, and internal device timing
is dependent on the duty cycle of the input clock signal. In such
applications, it may be appropriate to disable the duty cycle
stabilizer. In all other applications, enabling the DCS circuit is
recommended to maximize ac performance.
Refer to AN-501 Application Note, Aperture Uncertainty and ADC
System Performance, and AN-756 Application Note, Sampled
Systems and the Effects of Clock Phase Noise and Jitter, for more
information about jitter performance as it relates to ADCs.
Rev. 0 | Page 22 of 32
AD9634
When using the SPI port interface, the user can place the ADC
in power-down mode or standby mode. Standby mode allows
the user to keep the internal reference circuitry powered when
faster wake-up times are required. To put the part into standby
mode, set the internal power-down mode bits (Bits[1:0]) in the
power modes register (Address 0x08) to 10. See the Memory
Map section and AN-877 Application Note, Interfacing to High
Speed ADCs via SPI for additional details.
POWER DISSIPATION AND STANDBY MODE
As shown in Figure 57, the power dissipated by the AD9634 is
proportional to its sample rate. The data in Figure 57 was taken
using the same operating conditions as those used for the Typical
Performance Characteristics section.
0.4
0.3
0.2
0.1
0
0.25
0.20
0.15
0.10
0.05
0
DIGITAL OUTPUTS
TOTAL POWER
The AD9634 output drivers can be configured for either ANSI
LVDS or reduced swing LVDS using a 1.8 V DRVDD supply.
As detailed in the AN-877 Application Note, Interfacing to High
Speed ADCs via SPI, the data format can be selected for offset
binary, twos complement, or gray code when using the SPI
control.
I
AVDD
I
DRVDD
Digital Output Enable Function (OEB)
The AD9634 has a flexible three-state ability for the digital output
pins. The three-state mode is enabled using the SPI interface.
The data outputs can be three-stated by using the output enable
bar bit (Bit 4) in Register 0x14. This OEB function is not intended
for rapid access to the data bus.
40 55 70 85 100 115 130 145 160 175 190 205 220 235 250
ENCODE FREQUENCY (MSPS)
Figure 57. AD9634-250 Power and Current vs. Sample Rate
By setting the internal power-down mode bits (Bits[1:0]) in the
power modes register (Address 0x08) to 01, the AD9634 is placed
in power-down mode. In this state, the ADC typically dissipates
5 mW. During power-down, the output drivers are placed in a
high impedance state.
Timing
The AD9634 provides latched data with a pipeline delay of 10 input
sample clock cycles. Data outputs are available one propagation
delay (tPD) after the rising edge of the clock signal.
Low power dissipation in power-down mode is achieved by
shutting down the reference, reference buffer, biasing networks,
and clock. Internal capacitors are discharged when entering power-
down mode and then must be recharged when returning to
normal operation. As a result, wake-up time is related to the
time spent in power-down mode, and shorter power-down
cycles result in proportionally shorter wake-up times.
Minimize the length of the output data lines as well as the loads
placed on these lines to reduce transients within the AD9634.
These transients may degrade converter dynamic performance.
The lowest typical conversion rate of the AD9634 is 40 MSPS. At
clock rates below 40 MSPS, dynamic performance can degrade.
Data Clock Output (DCO)
The AD9634 also provides the data clock output (DCO) intended
for capturing the data in an external register. Figure 2 shows
timing diagram of the AD9634 output modes.
ADC OVERRANGE (OR)
The ADC overrange indicator is asserted when an overrange is
detected on the input of the ADC. The overrange condition is
determined at the output of the ADC pipeline and, therefore, is
subject to a latency of 10 ADC clock cycles. An overrange at the
input is indicated by this bit 10 clock cycles after it occurs.
Table 10. Output Data Format
Input (V)
VIN+ − VIN−, Input Span = 1.75 V p-p (V)
Offset Binary Output Mode
0000 0000 0000
0000 0000 0000
Twos Complement Mode (Default)
1000 0000 0000
1000 0000 0000
OR
1
0
VIN+ − VIN− < −0.875
VIN+ − VIN− = −0.875
VIN+ − VIN− = 0
1000 0000 0000
0000 0000 0000
0
VIN+ − VIN− = +0.875
VIN+ − VIN− > +0.875
1111 1111 1111
1111 1111 1111
0111 1111 1111
0111 1111 1111
0
1
Rev. 0 | Page 23 of 32
AD9634
SERIAL PORT INTERFACE (SPI)
The AD9634 serial port interface (SPI) allows the user to configure
the converter for specific functions or operations through a
structured register space provided inside the ADC. The SPI offers
added flexibility and customization, depending on the application.
Addresses are accessed via the serial port and can be written to
or read from via the port. Memory is organized into bytes that can
be further divided into fields. These fields are documented in the
Memory Map section. For detailed operational information, see
the AN-877 Application Note, Interfacing to High Speed ADCs
via SPI.
All data is composed of 8-bit words. The first bit of each individual
byte of serial data indicates whether a read or write command is
issued. This allows the serial data input/output (SDIO) pin to
change direction from an input to an output.
In addition to word length, the instruction phase determines
whether the serial frame is a read or write operation, allowing
the serial port to be used both to program the chip and to read
the contents of the on-chip memory. If the instruction is a readback
operation, performing a readback causes the serial data input/
output (SDIO) pin to change direction from an input to an output
at the appropriate point in the serial frame.
CONFIGURATION USING THE SPI
Data can be sent in MSB-first mode or in LSB-first mode. MSB-
first mode is the default on power-up and can be changed via
the SPI port configuration register. For more information about
this and other features, see the AN-877 Application Note,
Interfacing to High Speed ADCs via SPI.
Three pins define the SPI of this ADC: the SCLK pin, the SDIO
pin, and the CSB pin (see Table 11). The SCLK (serial clock) pin
is used to synchronize the read and write data presented from
and to the ADC. The SDIO (serial data input/output) pin is a
dual-purpose pin that allows data to be sent and read from the
internal ADC memory map registers. The CSB (chip select bar)
pin is an active-low control that enables or disables the read and
write cycles.
HARDWARE INTERFACE
The pins described in Table 11 comprise the physical interface
between the user programming device and the serial port of the
AD9634. The SCLK pin and the CSB pin function as inputs when
using the SPI interface. The SDIO pin is bidirectional, functioning
as an input during write phases and as an output during readback.
Table 11. Serial Port Interface Pins
Pin
Function
SCLK Serial clock. The serial shift clock input, which is used to
synchronize serial interface reads and writes.
SDIO Serial data input/output. A dual-purpose pin that
typically serves as an input or an output, depending on
the instruction being sent and the relative position in the
timing frame.
The SPI interface is flexible enough to be controlled by either
FPGAs or microcontrollers. One method for SPI configuration
is described in detail in the AN-812 Application Note,
Microcontroller-Based Serial Port Interface (SPI) Boot Circuit.
CSB
Chip select bar. An active-low control that gates the read
and write cycles.
The SPI port should not be active during periods when the full
dynamic performance of the converter is required. Because the
SCLK signal, the CSB signal, and the SDIO signal are typically
asynchronous to the ADC clock, noise from these signals can
degrade converter performance. If the on-board SPI bus is used for
other devices, it may be necessary to provide buffers between
this bus and the AD9634 to prevent these signals from transi-
tioning at the converter inputs during critical sampling periods.
The falling edge of CSB, in conjunction with the rising edge of
SCLK, determines the start of the framing. An example of the serial
timing and its definitions can be found in Figure 58 and Table 5.
Other modes involving the CSB are available. The CSB can be
held low indefinitely, which permanently enables the device;
this is called streaming. The CSB can stall high between bytes to
allow for additional external timing. When CSB is tied high, SPI
functions are placed in a high impedance mode. This mode turns
on any SPI pin secondary functions.
During an instruction phase, a 16-bit instruction is transmitted.
Data follows the instruction phase, and its length is determined
by the W0 and W1 bits.
Rev. 0 | Page 2ꢀ of 32
AD9634
Table 12. Features Accessible Using the SPI
SPI ACCESSIBLE FEATURES
Feature Name
Description
Table 12 provides a brief description of the general features that
are accessible via the SPI. These features are described in detail in
AN-877 Application Note, Interfacing to High Speed ADCs via
SPI.
Mode
Allows the user to set either power-down mode
or standby mode
Clock
Offset
Allows the user to access the DCS via the SPI
Allows the user to digitally adjust the
converter offset
Test I/O
Allows the user to set test modes to have
known data on output bits
Output Mode
Output Phase
Output Delay
VREF
Allows the user to set up outputs
Allows the user to set the output clock polarity
Allows the user to vary the DCO delay
Allows the user to set the reference voltage
Digital
Processing
Allows the user to enable the synchronization
features
tHIGH
tDS
tCLK
tH
tS
tDH
tLOW
CSB
SCLK DON’T CARE
SDIO DON’T CARE
DON’T CARE
R/W
W1
W0
A12
A11
A10
A9
A8
A7
D5
D4
D3
D2
D1
D0
DON’T CARE
Figure 58. Serial Port Interface Timing Diagram
Rev. 0 | Page 25 of 32
AD9634
MEMORY MAP
Default Values
READING THE MEMORY MAP REGISTER TABLE
After the AD9634 is reset, critical registers are loaded with
default values. The default values for the registers are given in
the memory map register table (see Table 13).
Each row in the memory map register table has eight bit
locations. The memory map is roughly divided into three
sections: the chip configuration registers (Address 0x00 to
Address 0x02), the transfer register (Address 0xFF), and the
ADC functions registers (Address 0x08 to Address 0x25),
including setup, control, and test.
Logic Levels
An explanation of logic level terminology follows:
•
“Bit is set” is synonymous with “bit is set to Logic 1” or
“writing Logic 1 for the bit.”
The memory map register table (Table 13) documents the
default hexadecimal value for each hexadecimal address shown.
The Bit 7 (MSB) column is the start of the default hexadecimal
value given. For example, Address 0x14, the output mode register,
has a hexadecimal default value of 0x01. This means that Bit 0 = 1
and the remaining bits are 0s. This setting is the default output
format value, which is twos complement. For more information
on this function and others, see the AN-877 Application Note,
Interfacing to High Speed ADCs via SPI. This document details
the functions controlled by Register 0x00 to Register 0x25.
•
“Clear a bit” is synonymous with “bit is set to Logic 0” or
“writing Logic 0 for the bit.”
Transfer Register Map
Address 0x08 to Address 0x20 are shadowed. Writes to these
addresses do not affect part operation until a transfer command is
issued by writing 0x01 to Address 0xFF, setting the transfer bit. This
allows these registers to be updated internally and simultaneously
when the transfer bit is set. The internal update takes place
when the transfer bit is set, and then the bit autoclears.
Open Locations
All address and bit locations that are not included in Table 13
are not currently supported for this device. Write 0s to unused
bits of a valid address location. Writing to these locations is
required only when part of an address location is open (for
example, Address 0x18). If the entire address location is open
(for example, Address 0x13), do not write to this address location.
Rev. 0 | Page 2ꢁ of 32
AD9634
MEMORY MAP REGISTER TABLE
All address and bit locations that are not included in Table 13 are not currently supported for this device.
Table 13. Memory Map Registers
Default Default
Addr
(Hex)
Register
Name
Bit 7
(MSB)
Bit 0
(LSB)
Value
(Hex)
Notes/
Comments
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Chip Configuration Registers
0x00
SPI port
configuration
0
LSB first
Soft reset
1
1
Soft reset
LSB first
0
0x18
Nibbles are
mirrored so
that LSB-
first mode
or MSB-first
mode is set
correctly,
regardless
of shift
mode.
0x01
0x02
Chip ID
8-bit chip ID[7:0], AD9ꢁ3ꢀ = 0x87 (default)
0x87
0x00
Read only.
Chip grade
Open
Open
Open
Open
Speed grade ID;
00 = 250 MSPS
01 = 210 MSPS
11 = 170 MSPS
Open
Open
Open
Open
Open
Speed
grade ID
used to
differentiate
devices;
read only.
Transfer Register
0xFF Transfer
Open
Open
Open
Open
Transfer
Synchro-
nously
transfers
data from
the master
shift
register to
the slave.
ADC Function Registers
0x08
Power modes
Open
Open
Open
Open
Open
Open
Open
Open
Open
Open
Internal power-down mode
00 = normal operation
01 = full power-down
10 = standby
0x00
Determines
various
generic
modes of
chip
operation.
11 = reserved
0x09
0x0B
Global clock
Clock divide
Open
Open
Open
Open
Open
Duty cycle
stabilizer
(default)
0x01
0x00
Input clock divider phase adjust
000 = no delay
Clock divide ratio
Clock divide
values other
than 000
auto-
matically
cause the
duty cycle
stabilizer to
become
000 = divide by 1
001 = divide by 2
010 = divide by 3
011 = divide by ꢀ
100 = divide by 5
101 = divide by ꢁ
110 = divide by 7
111 = divide by 8
001 = 1 input clock cycle
010 = 2 input clock cycles
011 = 3 input clock cycles
100 = ꢀ input clock cycles
101 = 5 input clock cycles
110 = ꢁ input clock cycles
111 = 7 input clock cycles
active.
0x0D
Test mode
Test mode
0 = contin-
uous/
repeat
pattern
1 = single
pattern
then zeros
Open
Reset PN
long gen
Reset PN
short gen
Output test mode
0x00
When this
register is
set, the test
data is
placed on
the output
pins in
place of
normal
data.
0000 = off (default)
0001 = midscale short
0010 = positive FS
0011 = negative FS
0100 = alternating checkerboard
0101 = PN long sequence
0110 = PN short sequence
0111 = one/zero word toggle
1000 = user test mode
1001 to 1110 = unused
1111 = ramp output
Rev. 0 | Page 27 of 32
AD9634
Default Default
Addr
(Hex)
Register
Name
Bit 7
(MSB)
Bit 0
(LSB)
Value
(Hex)
Notes/
Comments
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
0x0E
0x10
0x1ꢀ
BIST enable
Open
Open
Open
Open
Open
Open
Open
Reset BIST
sequence
Open
BIST enable
0x00
0x00
0x01
Offset adjust
Output mode
Open
Open
Offset adjust in LSBs from +31 to −32
(twos complement format)
Open
Open
Output
enable bar
0 = on
(default)
1 = off
Open
Output
invert
0 = normal
(default)
1 =
Output format
00 = offset binary
01 = twos complement
(default)
Configures
the outputs
and the
format of
the data.
10 = gray code
11 = reserved
inverted
0x15
Output adjust
Open
Open
Open
LVDS output drive current adjust
0000 = 3.72 mA output drive current
0001 = 3.5 mA output drive current (default)
0010 = 3.30 mA output drive current
0011 = 2.9ꢁ mA output drive current
0100 = 2.82 mA output drive current
0101 = 2.57 mA output drive current
0110 = 2.27 mA output drive current
0x01
0111 = 2.0 mA output drive current (reduced range)
1000 to 1111 = reserved
0x1ꢁ
0x17
Clock phase
control
Invert
DCO clock
Open
Open
Open
Open
Open
Open
Open
Open
Open
0x00
0x00
DCO output
delay
Enable
DCO
clock
delay
DCO clock delay
[delay = (3100 ps × register value/31 + 100)]
00000 = 100 ps
00001 = 200 ps
00010 = 300 ps
…
11110 = 3100 ps
11111 = 3200 ps
0x18
Input span
select
Open
Open
Open
Full-scale input voltage selection
01111 = 2.087 V p-p
…
00001 = 1.772 V p-p
00000 = 1.75 V p-p (default)
11111 = 1.727 V p-p
…
0x00
Full-scale
input
adjustment
in 0.022 V
steps.
10000 = 1.383 V p-p
0x19
0x1A
0x1B
0x1C
0x1D
0x1E
0x1F
0x20
0x2ꢀ
0x25
User Test
Pattern 1 LSB
User Test Pattern 1[7:0]
User Test Pattern 1[15:8]
User Test Pattern 2[7:0]
User Test Pattern 2[15:8]
User Test Pattern 3[7:0]
User Test Pattern 3[15:8]
User Test Pattern ꢀ[7:0]
User Test Pattern ꢀ[15:8]
BIST signature[7:0]
0x00
0x00
0x00
0x00
0x00
0x00
0x00
User Test
Pattern 1 MSB
User Test
Pattern 2 LSB
User Test
Pattern 2 MSB
User Test
Pattern 3 LSB
User Test
Pattern 3 MSB
User Test
Pattern ꢀ LSB
User Test
Pattern ꢀ MSB
0x00
0x00
BIST signature
LSB
Read only.
Read only.
BIST signature
MSB
BIST signature[15:8]
0x00
Rev. 0 | Page 28 of 32
AD9634
APPLICATIONS INFORMATION
The copper plane should have several vias to achieve the lowest
possible resistive thermal path for heat dissipation to flow through
the bottom of the PCB. These vias should be filled or plugged with
nonconductive epoxy.
DESIGN GUIDELINES
Before starting system-level design and layout of the AD9634, it
is recommended that the designer become familiar with these
guidelines, which describe the special circuit connections and
layout requirements needed for certain pins.
To maximize the coverage and adhesion between the ADC and
the PCB, overlay a silkscreen to partition the continuous plane on
the PCB into several uniform sections. This provides several tie
points between the ADC and the PCB during the reflow process.
Using one continuous plane with no partitions guarantees only one
tie point between the ADC and the PCB. See the evaluation
board for a PCB layout example. For detailed information about
the packaging and PCB layout of chip scale packages, refer to
the AN-772 Application Note, A Design and Manufacturing
Guide for the Lead Frame Chip Scale Package (LFCSP).
Power and Ground Recommendations
When connecting power to the AD9634, it is recommended that
two separate 1.8 V supplies be used: use one supply for analog
(AVDD) and a separate supply for digital outputs (DRVDD).
The designer can employ several different decoupling capacitors
to cover both high and low frequencies. Locate these capacitors
close to the point of entry at the PC board level and close to the
pins of the part with minimal trace length.
A single PCB ground plane should be sufficient when using the
AD9634. With proper decoupling and smart partitioning of the
PCB analog, digital, and clock sections, optimum performance
can be easily achieved.
VCM
Decouple the VCM pin to ground with a 0.1 μF capacitor, as
shown in Figure 48.
SPI Port
Exposed Paddle Thermal Heat Slug Recommendations
The SPI port should not be active during periods when the full
dynamic performance of the converter is required. Because the
SCLK, CSB, and SDIO signals are typically asynchronous to the
ADC clock, noise from these signals can degrade converter
performance. If the on-board SPI bus is used for other devices,
it may be necessary to provide buffers between this bus and the
AD9634 to keep these signals from transitioning at the converter
input pins during critical sampling periods.
It is mandatory that the exposed paddle on the underside of the
ADC be connected to analog ground (AGND) to achieve the
best electrical and thermal performance. A continuous, exposed
(no solder mask) copper plane on the PCB should be connected
to the AD9634 exposed paddle, Pin 0.
Rev. 0 | Page 29 of 32
AD9634
OUTLINE DIMENSIONS
5.10
5.00 SQ
4.90
0.30
0.25
0.18
PIN 1
INDICATOR
PIN 1
INDICATOR
25
32
24
1
0.50
BSC
*
3.75
EXPOSED
PAD
3.60 SQ
3.55
17
8
16
9
0.50
0.40
0.30
0.25 MIN
TOP VIEW
BOTTOM VIEW
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
0.80
0.75
0.70
0.05 MAX
0.02 NOM
SECTION OF THIS DATA SHEET.
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
*
COMPLIANT TO JEDEC STANDARDS MO-220-WHHD-5
WITH EXCEPTION TO EXPOSED PAD DIMENSION.
Figure 59. 32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
5 mm × 5 mm Body, Very Very Thin Quad
(CP-32-12)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
Temperature Range
Package Description
Package Option
CP-32-12
CP-32-12
CP-32-12
CP-32-12
AD9ꢁ3ꢀBCPZ-250
AD9ꢁ3ꢀBCPZRL7-250
AD9ꢁ3ꢀBCPZ-210
AD9ꢁ3ꢀBCPZRL7-210
AD9ꢁ3ꢀBCPZ-170
AD9ꢁ3ꢀBCPZRL7-170
AD9ꢁ3ꢀ-170EBZ
AD9ꢁ3ꢀ-210EBZ
AD9ꢁ3ꢀ-250EBZ
−ꢀ0°C to +85°C
−ꢀ0°C to +85°C
−ꢀ0°C to +85°C
−ꢀ0°C to +85°C
−ꢀ0°C to +85°C
−ꢀ0°C to +85°C
32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
Evaluation Board with AD9ꢁ3ꢀ and Software
CP-32-12
CP-32-12
Evaluation Board with AD9ꢁ3ꢀ and Software
Evaluation Board with AD9ꢁ3ꢀ and Software
1 Z = RoHS Compliant Part.
Rev. 0 | Page 30 of 32
AD9634
NOTES
Rev. 0 | Page 31 of 32
AD9634
NOTES
©2011 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D09996-0-7/11(0)
Rev. 0 | Page 32 of 32
相关型号:
©2020 ICPDF网 联系我们和版权申明