AD9777-EB [ADI]
16-Bit, 160 MSPS 2x/4x/8x Interpolating Dual TxDAC D/A Converter; 16位, 160 MSPS 2倍/ 4倍/ 8倍内插双通道TxDAC D / A转换器型号: | AD9777-EB |
厂家: | ADI |
描述: | 16-Bit, 160 MSPS 2x/4x/8x Interpolating Dual TxDAC D/A Converter |
文件: | 总60页 (文件大小:1777K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
16-Bit, 160 MSPS 2x/4x/8x
Interpolating Dual TxDAC+® D/A Converter
AD9777
Versatile input data interface
FEATURES
Twos complement/straight binary data coding
Dual-port or single-port interleaved input data
Single 3.3 V supply operation
16-bit resolution, 160 MSPS/400 MSPS input/output
data rate
Selectable 2×/4×/8× interpolating filter
Programmable channel gain and offset adjustment
fS/4, fS/8 digital quadrature modulation capability
Direct IF transmission mode for 70 MHz + IFs
Enables image rejection architecture
Fully compatible SPI® port
Power dissipation: typical 1.2 W @ 3.3 V
On-chip 1.2 V reference
80-lead thin quad flat package, exposed pad (TQFP_EP)
APPLICATIONS
Communications
Excellent ac performance
Analog quadrature modulation architecture
3G, multicarrier GSM, TDMA, CDMA systems
Broadband wireless, point-to-point microwave radios
Instrumentation/ATE
SFDR −73 dBc @ 2 MHz to 35 MHz
WCDMA ACPR 71 dB @ IF = 19.2 MHz
Internal PLL clock multiplier
Selectable internal clock divider
Versatile clock input
Differential/single-ended sine wave or
TTL/CMOS/LVPECL compatible
FUNCTIONAL BLOCK DIAGRAM
IDAC
COS
AD9777
HALF-
BAND
FILTER1*
HALF-
BAND
HALF-
BAND
GAIN
DAC
OFFSET
DAC
FILTER2* FILTER3*
DATA
SIN
fDAC/2, 4, 8
SIN
ASSEMBLER
IMAGE
REJECTION/
DUAL DAC
MODE
BYPASS
MUX
16
16
16
16
16
16
I
I/Q DAC
GAIN/OFFSET
REGISTERS
LATCH
I AND Q
NONINTERLEAVED
OR INTERLEAVED
DATA
16
16
16
Q
LATCH
16
FILTER
BYPASS
MUX
COS
WRITE
MUX
CONTROL
I
IDAC
SELECT
OUT
/2
(fDAC)
CLOCK OUT
/2
/2
/2
SPI INTERFACE AND
CONTROL REGISTERS
PRESCALER
DIFFERENTIAL
CLK
PHASE DETECTOR
AND VCO
* HALF-BAND FILTERS ALSO CAN BE
CONFIGURED FOR ZERO STUFFING ONLY
PLL CLOCK MULTIPLIER AND CLOCK DIVIDER
Figure 1.
Rev. C
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
© 2006 Analog Devices, Inc. All rights reserved.
AD9777
TABLE OF CONTENTS
Features .............................................................................................. 1
Sleep/Power-Down Modes........................................................ 29
Two Port Data Input Mode ....................................................... 29
PLL Enabled, Two-Port Mode.................................................. 30
DATACLK Inversion.................................................................. 30
DATACLK Driver Strength....................................................... 30
PLL Enabled, One-Port Mode .................................................. 30
ONEPORTCLK Inversion......................................................... 31
ONEPORTCLK Driver Strength.............................................. 31
IQ Pairing.................................................................................... 31
PLL Disabled, Two-Port Mode................................................. 31
PLL Disabled, One-Port Mode................................................. 32
Digital Filter Modes ................................................................... 32
Amplitude Modulation.............................................................. 32
Modulation, No Interpolation.................................................. 34
Modulation, Interpolation = 2× ............................................... 35
Modulation, Intermodulation = 4× ......................................... 36
Modulation, Intermodulation = 8× ......................................... 37
Zero Stuffing ............................................................................... 38
Interpolating (Complex Mix Mode)........................................ 38
Operations on Complex Signals............................................... 38
Applications....................................................................................... 1
General Description......................................................................... 4
Product Highlights....................................................................... 4
Specifications..................................................................................... 5
DC Specifications ......................................................................... 5
Dynamic Specifications ............................................................... 6
Digital Specifications ................................................................... 7
Digital Filter Specifications......................................................... 8
Absolute Maximum Ratings............................................................ 9
Thermal Characteristics .............................................................. 9
ESD Caution.................................................................................. 9
Pin Configuration and Function Descriptions........................... 10
Terminology .................................................................................... 12
Typical Performance Characteristics ........................................... 13
Mode Control (via SPI Port)..................................................... 18
Register Description................................................................... 20
Functional Description.................................................................. 22
Serial Interface for Register Control........................................ 22
General Operation of the Serial Interface............................... 22
Instruction Byte .......................................................................... 23
R/W .............................................................................................. 23
N1, N0.......................................................................................... 23
A4, A3, A2, A1, A0..................................................................... 23
Serial Interface Port Pin Descriptions ..................................... 23
MSB/LSB Transfers..................................................................... 23
Notes on Serial Port Operation ................................................ 25
DAC Operation........................................................................... 25
1R/2R Mode ................................................................................ 26
CLOCK Input Configuration ................................................... 26
Programmable PLL .................................................................... 27
Power Dissipation....................................................................... 29
Complex Modulation and Image Rejection of Baseband
Signals .......................................................................................... 39
Image Rejection and Sideband Suppressions of Modulated
Carriers........................................................................................ 41
Applying the Output Configurations........................................... 46
Unbuffered Differential Output, Equivalent Circuit ............. 46
Differential Coupling Using a Transformer............................ 46
Differential Coupling Using an Op Amp................................ 47
Interfacing with the AD8345 Quadrature Modulator........... 47
Evaluation Board ............................................................................ 48
Outline Dimensions....................................................................... 58
Ordering Guide .......................................................................... 58
Rev. C | Page 2 of 60
AD9777
REVISION HISTORY
Edits to Register Description—Address 07h, 0Bh Section...... 16
Edits to Equation 1........................................................................ 16
Edits to MSB/LSB Transfers Section........................................... 18
Changes to Figure 8 ...................................................................... 20
Edits to Programmable PLL Section........................................... 21
Added new Figure 14.................................................................... 22
Renumbered Figures 15 to 69...................................................... 22
Added Two-Port Data Input Mode Section............................... 23
Edits to PLL Enabled, Two-Port Mode Section ........................ 24
Edits to Figure 19 ......................................................................... 24
Edits to Figure 21 .......................................................................... 25
Edits to PLL Disabled, Two-Port Mode Section ....................... 25
Edits to Figure 22 .......................................................................... 25
Edits to Figure 23 .......................................................................... 26
Edits to Figure 26a ........................................................................ 27
Changes to Figures 53 and 54...................................................... 38
Edits to Evaluation Board Section .............................................. 39
Changes to Figures 56 to 59......................................................... 40
Replaced Figures 60 to 69 ............................................................ 42
Updated Outline Dimensions...................................................... 49
1/06—Rev. B to Rev. C
Updated Formatting .........................................................Universal
Changes to Figure 32 .................................................................... 22
Changes to Figure 108.................................................................. 54
Updated Outline Dimensions ..................................................... 58
Changes to Ordering Guide......................................................... 58
6/04—Data Sheet Changed from Rev. A to Rev. B.
Changes to DC Specifications ....................................................... 5
Changes to Absolute Maximum Ratings...................................... 8
Changes to DAC Operation Section........................................... 25
Changes to Figure 49, Figure 50, and Figure 51........................ 29
Changes to the PLL Enabled, One-Port Mode Section............ 30
Changes to the PLL Disabled, One-Port Mode Section........... 32
Changes to the Ordering Guide .................................................. 57
Updated the Outline Dimensions ............................................... 57
3/03—Data Sheet Changed from Rev. 0 to Rev. A.
Edits to Features .............................................................................. 1
Edits to DC Specifications ............................................................. 3
Edits to Dynamic Specifications.................................................... 4
Edits to Pin Function Descriptions............................................... 7
Edits to Table I ............................................................................... 14
Edits to Register Description—Address 02h Section............... 15
Edits to Register Description—Address 03h Section............... 16
7/02—Revision 0: Initial Version
Rev. C | Page 3 of 60
AD9777
GENERAL DESCRIPTION
The AD97771 is the 16-bit member of the AD977x pin
compatible, high performance, programmable 2×/4×/8×
interpolating TxDAC+ family. The AD977x family features a
serial port interface (SPI) that provides a high level of
programmability, thus allowing for enhanced system level
options. These options include selectable 2×/4×/8× interpola-
tion filters; fS/2, fS/4, or fS/8 digital quadrature modulation with
image rejection; a direct IF mode; programmable channel gain
and offset control; programmable internal clock divider;
straight binary or twos complement data interface; and a single-
port or dual-port data interface.
Targeted at wide dynamic range, multicarrier, and
multistandard systems, the superb baseband performance of the
AD9777 is ideal for wideband CDMA, multicarrier CDMA,
multicarrier TDMA, multicarrier GSM, and high performance
systems employing high-order QAM modulation schemes. The
image rejection feature simplifies and can help to reduce the
number of signal band filters needed in a transmit signal chain.
The direct IF mode helps to eliminate a costly mixer stage for a
variety of communications systems.
PRODUCT HIGHLIGHTS
1. The AD9777 is the 16-bit member of the AD977x pin
compatible, high performance, programmable 2×/4×/8×
interpolating TxDAC+ family.
The selectable 2×/4×/8× interpolation filters simplify the
requirements of the reconstruction filters while simultaneously
enhancing the TxDAC+ family’s pass-band noise/distortion
performance. The independent channel gain and offset adjust
registers allow the user to calibrate LO feedthrough and sideband
suppression errors associated with analog quadrature modulators.
The 6 dB of gain adjustment range can also be used to control the
output power level of each DAC.
2. Direct IF transmission is possible for 70 MHz + IFs
through a novel digital mixing process.
3. fS/2, fS/4, and fS/8 digital quadrature modulation and user
selectable image rejection simplify/remove cascaded SAW
filter stages.
4. A 2×/4×/8× user selectable interpolating filter eases data
rate and output signal reconstruction filter requirements.
The AD9777 features the ability to perform fS/2, fS/4, and fS/8
digital modulation and image rejection when combined with an
analog quadrature modulator. In this mode, the AD9777 accepts I
and Q complex data (representing a single or multicarrier wave-
form), generates a quadrature modulated IF signal along with its
orthogonal representation via its dual DACs, and presents these
two reconstructed orthogonal IF carriers to an analog quadrature
modulator to complete the image rejection upconversion process.
Another digital modulation mode (that is, the direct IF mode)
allows the original baseband signal representation to be fre-
quency translated such that pairs of images fall at multiples of
one-half the DAC update rate.
5. User selectable twos complement/straight binary data
coding.
6. User programmable channel gain control over 1 dB range
in 0.01 dB increments.
7. User programmable channel offset control 10ꢀ over the
FSR.
8. Ultrahigh speed 400 MSPS DAC conversion rate.
9. Internal clock divider provides data rate clock for easy
interfacing.
The AD977x family includes a flexible clock interface accepting
differential or single-ended sine wave or digital logic inputs. An
internal PLL clock multiplier is included and generates the
necessary on-chip high frequency clocks. It can also be disabled
to allow the use of a higher performance external clock source.
An internal programmable divider simplifies clock generation
in the converter when using an external clock source. A flexible
data input interface allows for straight binary or twos comple-
ment formats and supports single-port interleaved or dual-port
data.
10. Flexible clock input with single-ended or differential input,
CMOS, or 1 V p-p LO sine wave input capability.
11. Low power: Complete CMOS DAC operates on 1.2 W
from a 3.1 V to 3.5 V single supply. The 20 mA full-scale
current can be reduced for lower power operation, and
several sleep functions are provided to reduce power
during idle periods.
12. On-chip voltage reference: The AD9777 includes a 1.20 V
temperature compensated band gap voltage reference.
Dual high performance DAC outputs provide a differential
current output programmable over a 2 mA to 20 mA range. The
AD9777 is manufactured on an advanced 0.35 micron CMOS
process, operates from a single-supply of 3.1 V to 3.5 V, and
consumes 1.2 W of power.
13. An 80-lead thin quad flat package, exposed pad
(TQFP_EP).
1 Protected by U.S. Patent Numbers, 5,568,145; 5,689,257; and 5,703,519.
Other patents pending.
Rev. C | Page 4 of 60
AD9777
SPECIFICATIONS
DC SPECIFICATIONS
TMIN to TMAX, AVDD = 3.3 V, CLKVDD = 3.3 V, DVDD = 3.3 V, PLLVDD = 3.3 V, IOUTFS = 20 mA, unless otherwise noted.
Table 1.
Parameter
Min
Typ
Max
Unit
RESOLUTION
DC Accuracy1
16
Bits
Integral Nonlinearity
6
3
LSB
LSB
Differential Nonlinearity
ANALOG OUTPUT (for 1R and 2R Gain Setting Modes)
Offset Error
Gain Error (with Internal Reference)
Gain Matching
Full-Scale Output Current2
Output Compliance Range
Output Resistance
−6.5
+6.5
−0.025
−1.0
−1
2
−1.0
0.01
+0.025
+1.0
+1
20
+1.25
% of FSR
% of FSR
% of FSR
mA
V
kΩ
0.1
200
3
Output Capacitance
pF
Gain, Offset Cal DACs, Monotonicity Guaranteed
REFERENCE OUTPUT
Reference Voltage
1.14
0.1
1.20
100
1.26
1.25
V
nA
Reference Output Current3
REFERENCE INPUT
Input Compliance Range
Reference Input Resistance
Small Signal Bandwidth
TEMPERATURE COEFFICIENTS
Offset Drift
Gain Drift (with Internal Reference)
Reference Voltage Drift
POWER SUPPLY
V
kΩ
MHz
7
0.5
0
50
50
ppm of FSR/°C
ppm of FSR/°C
ppm/°C
AVDD
Voltage Range
3.1
3.1
3.3
72.5
23.3
3.5
76
26
V
mA
mA
4
Analog Supply Current (IAVDD
IAVDD in SLEEP Mode
CLKVDD (PLL OFF)
)
Voltage Range
3.3
8.5
3.5
10.0
V
mA
4
Clock Supply Current (ICLKVDD
CLKVDD (PLL ON)
Clock Supply Current (ICLKVDD
DVDD
)
)
23.5
mA
Voltage Range
3.1
3.3
34
380
1.75
6.0
0.4
3.5
41
410
V
mA
mW
W
mW
% of FSR/V
°C
4
Digital Supply Current (IDVDD
)
Nominal Power Dissipation4
5
PDIS
PDIS in PWDN
Power Supply Rejection Ratio—AVDD
OPERATING RANGE
−40
+85
1 Measured at IOUTA driving a virtual ground.
2 Nominal full-scale current, IOUTFS, is 32× the IREF current.
3 Use an external amplifier to drive any external load.
4 100 MSPS fDAC with fOUT = 1 MHz, all supplies = 3.3 V, no interpolation, no modulation.
5 400 MSPS fDAC, fDATA = 50 MSPS, fS/2 modulation, PLL enabled.
Rev. C | Page 5 of 60
AD9777
DYNAMIC SPECIFICATIONS
TMIN to TMAX, AVDD = 3.3 V, CLKVDD = 3.3 V, DVDD = 3.3 V, PLLVDD = 0 V, IOUTFS = 20 mA, Interpolation = 2×, differential
transformer-coupled output, 50 Ω doubly terminated, unless otherwise noted.
Table 2.
Parameter
Min
Typ
Max
Unit
DYNAMIC PERFORMANCE
Maximum DAC Output Update Rate (fDAC
Output Settling Time (tST) (to 0.025%)
Output Rise Time (10% to 90%)1
Output Fall Time (10% to 90%)1
Output Noise (IOUTFS = 20 mA)
AC LINEARITY—BASEBAND MODE
)
400
MSPS
ns
ns
ns
pA/√Hz
11
0.8
0.8
50
Spurious-Free Dynamic Range (SFDR) to Nyquist (fOUT = 0 dBFS)
fDATA = 100 MSPS, fOUT = 1 MHz
fDATA = 65 MSPS, fOUT = 1 MHz
fDATA = 65 MSPS, fOUT = 15 MHz
fDATA = 78 MSPS, fOUT = 1 MHz
fDATA = 78 MSPS, fOUT = 15 MHz
fDATA = 160 MSPS, fOUT = 1 MHz
fDATA = 160 MSPS, fOUT = 15 MHz
71
85
85
84
85
83
85
83
dBc
dBc
dBc
dBc
dBc
dBc
dBc
Spurious-Free Dynamic Range within a 1 MHz Window
fOUT = 0 dBFS, fDATA = 100 MSPS, fOUT = 1 MHz
Two-Tone Intermodulation (IMD) to Nyquist (fOUT1 = fOUT2 = −6 dBFS)
fDATA = 65 MSPS, fOUT1 = 10 MHz; fOUT2 = 11 MHz
fDATA = 65 MSPS, fOUT1 = 20 MHz; fOUT2 = 21 MHz
fDATA = 78 MSPS, fOUT1 = 10 MHz; fOUT2 = 11 MHz
fDATA = 78 MSPS, fOUT1 = 20 MHz; fOUT2 = 21 MHz
fDATA = 160 MSPS, fOUT1 = 10 MHz; fOUT2 = 11 MHz
fDATA = 160 MSPS, fOUT1 = 20 MHz; fOUT2 = 21 MHz
Total Harmonic Distortion (THD)
73
99.1
dBc
85
78
85
78
85
84
dBc
dBc
dBc
dBc
dBc
dBc
fDATA = 100 MSPS, fOUT = 1 MHz; 0 dBFS
−71
−83
dB
Signal-to-Noise Ratio (SNR)
fDATA = 78 MSPS, fOUT = 5 MHz; 0 dBFS
fDATA = 160 MSPS, fOUT = 5 MHz; 0 dBFS
79
75
dB
dB
Adjacent Channel Power Ratio (ACPR)
WCDMA with 3.84 MHz BW, 5 MHz Channel Spacing
IF = Baseband, fDATA = 76.8 MSPS
IF = 19.2 MHz, fDATA = 76.8 MSPS
73
73
dBc
dBc
Four-Tone Intermodulation
21 MHz, 22 MHz, 23 MHz, and 24 MHz at −12 dBFS (fDATA = MSPS, Missing Center)
AC LINEARITY—IF MODE
Four-Tone Intermodulation at IF = 200 MHz
201 MHz, 202 MHz, 203 MHz, and 204 MHz at −12 dBFS (fDATA = 160 MSPS, fDAC = 320 MHz)
76
72
dBFS
dBFS
1 Measured single-ended into 50 Ω load.
Rev. C | Page 6 of 60
AD9777
DIGITAL SPECIFICATIONS
TMIN to TMAX, AVDD = 3.3 V, CLKVDD = 3.3 V, PLLVDD = 0 V, DVDD = 3.3 V, IOUTFS = 20 mA, unless otherwise noted.
Table 3.
Parameter
Min
Typ
Max
Unit
DIGITAL INPUTS
Logic 1 Voltage
Logic 0 Voltage
2.1
3
0
V
V
0.9
Logic 1 Current
Logic 0 Current
Input Capacitance
CLOCK INPUTS
−10
−10
+10
+10
µA
µA
pF
5
Input Voltage Range
Common-Mode Voltage
Differential Voltage
SERIAL CONTROL BUS
Maximum SCLK Frequency (fSLCK
0
0.75
0.5
3
2.25
V
V
V
1.5
1.5
)
15
30
30
MHz
ns
ns
Mimimum Clock Pulse Width High (tPWH
Mimimum Clock Pulse Width Low (tPWL
)
)
Maximum Clock Rise/Fall Time
Minimum Data/Chip Select Setup Time (tDS
1
ms
ns
ns
)
25
0
Minimum Data Hold Time (tDH
)
Maximum Data Valid Time (tDV
RESET Pulse Width
Inputs (SDI, SDIO, SCLK, CSB)
Logic 1 Voltage
)
30
ns
ns
1.5
2.1
3
0
V
V
Logic 0 Voltage
0.9
Logic 1 Current
Logic 0 Current
Input Capacitance
SDIO Output
−10
−10
+10
+10
µA
µA
pF
5
Logic 1 Voltage
DRVDD − 0.6
V
Logic 0 Voltage
0.4
V
Logic 1 Current
Logic 0 Current
30
30
50
50
mA
mA
Rev. C | Page 7 of 60
AD9777
DIGITAL FILTER SPECIFICATIONS
20
0
Table 4. Half-Band Filter No. 1 (43 Coefficients)
Tap
Coefficient
1, 43
2, 42
3, 41
4, 40
5, 39
6, 38
7, 37
8, 36
8
0
−29
0
67
0
−134
0
244
0
−414
0
673
0
−1,079
0
1,772
0
−3,280
0
10,364
16,384
–20
–40
–60
–80
–100
–120
9, 35
10, 34
11, 33
12, 32
13, 31
14, 30
15, 29
16, 28
17, 27
18, 26
19, 25
20, 24
21, 23
22
0
0
0
0.5
1.0
1.5
2.0
2.0
8
fOUT (NORMALIZED TO INPUT DATA RATE)
Figure 2. 2× Interpolating Filter Response
20
0
–20
–40
–60
–80
–100
–120
Table 5. Half-Band Filter No. 2 (19 Coefficients)
Tap
Coefficient
1, 19
2, 18
3, 17
4, 16
5, 15
6, 14
7, 13
8, 12
9, 11
10
19
0
−120
0
438
0
−1,288
0
5,047
8,192
0.5
1.0
1.5
fOUT (NORMALIZED TO INPUT DATA RATE)
Figure 3. 4× Interpolating Filter Response
20
0
–20
–40
–60
–80
–100
–120
Table 6. Half-Band Filter No. 3 (11 Coefficients)
Tap
1, 11
2, 10
3, 9
4, 8
5, 7
6
Coefficient
7
0
−53
0
302
512
2
4
6
fOUT (NORMALIZED TO INPUT DATA RATE)
Figure 4. 8× Interpolating Filter Response
Rev. C | Page 8 of 60
AD9777
ABSOLUTE MAXIMUM RATINGS
Table 7.
Parameter
With Respect To
AGND, DGND, CLKGND
AVDD, DVDD, CLKVDD
AGND, DGND, CLKGND
AGND
AGND
DGND
DGND
CLKGND
Min
−0.3
−4.0
−0.3
−0.3
−1.0
−0.3
−0.3
−0.3
−0.3
−0.3
Max
Unit
V
V
V
V
V
V
V
V
V
V
°C
°C
°C
AVDD, DVDD, CLKVDD
AVDD, DVDD, CLKVDD
AGND, DGND, CLKGND
REFIO, FSADJ1/FSADJ2
IOUTA, IOUTB
P1B15 to P1B0, P2B15 to P2B0, RESET
DATACLK/PLL_LOCK
CLK+, CLK−
+4.0
+4.0
+0.3
AVDD + 0.3
AVDD + 0.3
DVDD + 0.3
DVDD + 0.3
CLKVDD + 0.3
CLKVDD + 0.3
DVDD + 0.3
125
LPF
CLKGND
DGND
SPI_CSB, SPI_CLK, SPI_SDIO, SPI_SDO
Junction Temperature
Storage Temperature
Lead Temperature (10 sec)
−65
+150
300
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only;
functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is
not implied. Exposure to absolute maximum ratings for extended periods may affect device reliability.
THERMAL CHARACTERISTICS
Thermal Resistance
80-lead thin quad flat package, exposed pad [TQFP_EP]
θJA = 23.5°C/W (With thermal pad soldered to PCB)
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the
human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. C | Page 9 of 60
AD9777
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
1
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
FSADJ1
FSADJ2
REFIO
RESET
SPI_CSB
SPI_CLK
SPI_SDIO
SPI_SDO
DGND
CLKVDD
LPF
PIN 1
2
3
CLKVDD
CLKGND
CLK+
4
5
6
CLK–
7
CLKGND
DATACLK/PLL_LOCK
DGND
AD9777
TxDAC+
TOP VIEW
(Not to Scale)
8
9
10
11
12
13
14
15
16
17
18
19
20
DVDD
DVDD
P2B0 (LSB)
P2B1
P1B15 (MSB)
P1B14
P2B2
P1B13
P2B3
P1B12
P2B4
P1B11
P1B10
P2B5
DGND
DGND
DVDD
DVDD
P1B9
P2B6
P1B8
P2B7
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
NC = NO CONNECT
Figure 5. Pin Configuration
Rev. C | Page 10 of 60
AD9777
Table 8. Pin Function Description
Pin No.
Mnemonic
CLKVDD
LPF
Description
1, 3
2
Clock Supply Voltage.
PLL Loop Filter.
4, 7
5
6
CLKGND
CLK+
CLK−
Clock Supply Common.
Differential Clock Input.
Differential Clock Input.
8
DATACLK/PLL_LOCK
With the PLL enabled, this pin indicates the state of the PLL. A read of a Logic 1 indicates the
PLL is in the locked state. Logic 0 indicates the PLL has not achieved lock. This pin may also be
programmed to act as either an input or output (Address 02h, Bit 3) DATACLK signal running
at the input data rate.
9, 17, 25,
35, 44, 52
DGND
Digital Common.
10, 18, 26,
36, 43, 51
11 to 16, 19
to 24, 27 to
30
DVDD
Digital Supply Voltage.
Port 1 Data Inputs.
P1B15 (MSB) to P1B0 (LSB)
31
IQSEL/P2B15 (MSB)
ONEPORTCLK/P2B14
In one-port mode, IQSEL = 1 followed by a rising edge of the differential input clock latches
the data into the I channel input register. IQSEL = 0 latches the data into the Q channel input
register. In two-port mode, this pin becomes the Port 2 MSB.
With the PLL disabled and the AD9777 in one-port mode, this pin becomes a clock output
that runs at twice the input data rate of the I and Q channels. This allows the AD9777 to
accept and demux interleaved I and Q data to the I and Q input registers.
32
33, 34, 37 to
42, 45 to 50
53
P2B13 to P2B0 (LSB)
SPI_SDO
Port 2 Data Inputs.
In the case where SDIO is an input, SDO acts as an output. When SDIO becomes an output,
SDO enters a High-Z state. This pin can also be used as an output for the data rate clock. For
more information, see the Two Port Data Input Mode section.
54
55
56
57
SPI_SDIO
SPI_CLK
SPI_CSB
RESET
Bidirectional Data Pin. Data direction is controlled by Bit 7 of Register Address 00h. The
default setting for this bit is 0, which sets SDIO as an input.
Data input to the SPI port is registered on the rising edge of SPI_CLK. Data output on the SPI
port is registered on the falling edge.
Chip Select/SPI Data Synchronization. On momentary logic high, resets SPI port logic and
initializes instruction cycle.
Logic 1 resets all of the SPI port registers, including Address 00h, to their default values. A
software reset can also be done by writing a Logic 1 to SPI Register 00h, Bit 5. However, the
software reset has no effect on the bits in Address 00h.
58
59
60
REFIO
Reference Output, 1.2 V Nominal.
Full-Scale Current Adjust, Q Channel.
Full-Scale Current Adjust, I Channel.
Analog Supply Voltage.
FSADJ2
FSADJ1
AVDD
61, 63, 65,
76, 78, 80
62, 64, 66, 67, AGND
70, 71, 74,
Analog Common.
75, 77, 79
68, 69
72, 73
IOUTB2, IOUTA2
IOUTB1, IOUTA1
Differential DAC Current Outputs, Q Channel.
Differential DAC Current Outputs, I Channel.
Rev. C | Page 11 of 60
AD9777
TERMINOLOGY
Adjacent Channel Power Ratio (ACPR)
A ratio in dBc between the measured power within a channel
relative to its adjacent channel.
Monotonicity
A DAC is monotonic if the output either increases or remains
constant as the digital input increases.
Complex Image Rejection
Offset Error
In a traditional two-part upconversion, two images are created
around the second IF frequency. These images are redundant and
have the effect of wasting transmitter power and system bandwidth.
By placing the real part of a second complex modulator in series
with the first complex modulator, either the upper or lower
frequency image near the second IF can be rejected.
The deviation of the output current from the ideal of 0 is called
offset error. For IOUTA, 0 mA output is expected when the inputs
are all 0. For IOUTB, 0 mA output is expected when all inputs are
set to 1.
Output Compliance Range
The range of allowable voltage at the output of a current-output
DAC. Operation beyond the maximum compliance limits may
cause either output stage saturation or breakdown, resulting in
nonlinear performance.
Complex Modulation
The process of passing the real and imaginary components of a
signal through a complex modulator (transfer function = ejωt
=
cosωt + jsinωt) and realizing real and imaginary components
on the modulator output.
Pass Band
Frequency band in which any input applied therein passes
unattenuated to the DAC output.
Differential Nonlinearity (DNL)
DNL is the measure of the variation in analog value, normalized to
full scale, associated with a 1 LSB change in digital input code.
Power Supply Rejection
The maximum change in the full-scale output as the supplies
are varied from minimum to maximum specified voltages.
Gain Error
The difference between the actual and ideal output span. The
actual span is determined by the output when all inputs are set
to 1 minus the output when all inputs are set to 0.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the measured output signal
to the rms sum of all other spectral components below the
Nyquist frequency, excluding the first six harmonics and dc.
The value for SNR is expressed in decibels.
Glitch Impulse
Asymmetrical switching times in a DAC give rise to undesired
output transients that are quantified by a glitch impulse. It is
specified as the net area of the glitch in pV-s.
Spurious-Free Dynamic Range
The difference, in dB, between the rms amplitude of the
output signal and the peak spurious signal over the specified
bandwidth.
Group Delay
Number of input clocks between an impulse applied at the
device input and the peak DAC output current. A half-band FIR
filter has constant group delay over its entire frequency range.
Settling Time
The time required for the output to reach and remain within a
specified error band about its final value, measured from the
start of the output transition.
Impulse Response
Response of the device to an impulse applied to the input.
Interpolation Filter
Stop-Band Rejection
If the digital inputs to the DAC are sampled at a multiple rate of
fDATA (interpolation rate), a digital filter can be constructed that
has a sharp transition band near fDATA/2. Images that would
typically appear around fDAC (output data rate) can be greatly
suppressed.
The amount of attenuation of a frequency outside the pass band
applied to the DAC, relative to a full-scale signal applied at the
DAC input within the pass band.
Temperature Drift
It is specified as the maximum change from the ambient (25°C)
value to the value at either TMIN or TMAX. For offset and gain
drift, the drift is reported in ppm of full-scale range (FSR) per
°C. For reference drift, the drift is reported in ppm per °C.
Linearity Error
(Also called integral nonlinearity or INL) Linearity error is
defined as the maximum deviation of the actual analog output
from the ideal output, determined by a straight line drawn from
zero to full scale.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of the first six harmonic
components to the rms value of the measured fundamental. It is
expressed as a percentage or in decibels (dB).
Rev. C | Page 12 of 60
AD9777
TYPICAL PERFORMANCE CHARACTERISTICS
T = 25°C, AVDD = 3.3 V, CLKVDD = 3.3 V, DVDD = 3.3 V, IOUTFS = 20 mA, Interpolation = 2×, differential transformer-coupled output,
50 Ω doubly terminated, unless otherwise noted.
10
10
0
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–10
–20
–30
–40
–50
–60
–70
–80
–90
0
65
130
0
50
100
150
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 6. Single-Tone Spectrum @ fDATA = 65 MSPS with fOUT = fDATA/3
Figure 9. Single-Tone Spectrum @ fDATA = 78 MSPS with fOUT = fDATA/3
90
90
0dBFS
0dBFS
85
85
80
75
–6dBFS
80
75
70
–6dBFS
70
–12dBFS
65
–12dBFS
65
60
55
50
60
55
50
0
5
10
15
20
25
30
0
5
10
15
20
25
30
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 7. In-Band SFDR vs. fOUT @ fDATA = 65 MSPS
Figure 10. In-Band SFDR vs. fOUT @ fDATA = 78 MSPS
90
85
80
75
70
65
60
55
50
90
85
80
75
70
65
60
55
50
0dBFS
–12dBFS
–12dBFS 0dBFS
–6dBFS
–6dBFS
0
5
10
15
20
25
30
0
5
10
15
20
25
30
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 8. Out-of-Band SFDR vs. fOUT @ fDATA = 65 MSPS
Figure 11. Out-of-Band SFDR vs. fOUT @ fDATA = 78 MSPS
Rev. C | Page 13 of 60
AD9777
10
0
90
85
80
75
70
65
60
55
50
0dBFS
–10
–20
–30
–40
–50
–60
–70
–80
–3dBFS
–6dBFS
–90
0
100
200
300
0
5
10
15
20
25
30
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 12. Single-Tone Spectrum @ fDATA = 160 MSPS with fOUT = fDATA/3
Figure 15. Third-Order IMD Products vs. Two-Tone fOUT @ fDATA = 65 MSPS
90
90
0dBFS
0dBFS
85
85
80
75
80
75
70
–6dBFS
–3dBFS
70
65
60
55
50
–6dBFS
–12dBFS
65
60
55
50
0
10
20
30
40
50
0
5
10
15
20
25
30
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 13. In-Band SFDR vs. fOUT @ fDATA = 160 MSPS
Figure 16. Third-Order IMD Products vs. Two-Tone fOUT @ fDATA = 78 MSPS
90
85
80
75
70
65
60
55
50
90
0dBFS
85
80
–3dBFS
75
–6dBFS
–12dBFS
–6dBFS
70
65
60
55
50
0dBFS
0
10
20
30
40
50
0
10
20
30
40
50
60
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 14. Out-of-Band SFDR vs. fOUT @ fDATA = 160 MSPS
Figure 17. Third-Order IMD Products vs. Two-Tone fOUT @ fDATA = 160 MSPS
Rev. C | Page 14 of 60
AD9777
90
85
80
75
70
65
60
55
50
90
85
80
75
70
65
60
55
50
4
×
0dBFS
–3dBFS
–6dBFS
8×
1
×
2×
0
10
20
30
40
50
60
3.1
3.2
3.3
3.4
3.5
FREQUENCY (MHz)
AVDD (V)
Figure 18. Third-Order IMD Products vs. Two-Tone fOUT and Interpolation
Rate, 1× fDATA = 160 MSPS, 2× fDATA = 160 MSPS,
Figure 21. Third-Order IMD Products vs. AVDD @ fOUT = 10 MHz,
f
DAC = 320 MSPS, fDATA = 160 MSPS
4× fDATA = 80 MSPS, 8× fDATA = 50 MSPS
90
90
85
80
75
70
65
60
55
50
8×
85
PLL OFF
80
4×
75
1×
70
2×
PLL ON
65
60
55
50
–15
–10
–5
0
0
50
100
150
A
(dBFS)
INPUT DATA RATE (MSPS)
OUT
Figure 19. Third-Order IMD Products vs. Two-Tone AOUT and Interpolation
Rate, fDATA = 50 MSPS in All Cases, 1× fDAC = 50 MSPS, 2× fDAC = 100 MSPS,
4× fDAC = 200 MSPS, 8× fDAC = 400 MSPS
Figure 22. SNR vs. Data Rate for fOUT = 5 MHz
90
90
85
80
75
70
65
60
55
50
78MSPS
85
80
75
70
65
60
55
50
0dBFS
–6dBFS
fDATA = 65MSPS
160MSPS
–12dBFS
3.1
3.2
3.3
AVDD (V)
3.4
3.5
–50
0
50
100
TEMPERATURE (°C)
Figure 20. SFDR vs. AVDD fOUT = 10 MHz, fDAC = 320 MSPS, fDATA = 160 MSPS
Figure 23. SFDR vs. Temperature @ fOUT = fDATA/11
Rev. C | Page 15 of 60
AD9777
0
–20
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–40
–60
–80
–100
0
–100
0
5
10
15
20
25
30
35
40
45
50
100
150
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 27. Two-Tone IMD Performance, fDATA = 90 MSPS, Interpolation = 4×
Figure 24. Single-Tone Spurious Performance, fOUT = 10 MHz,
f
DATA = 150 MSPS, No Interpolation
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
0
–20
–40
–60
–80
–100
0
50
100
150
200
250
300
0
10
20
30
40
50
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 25. Two-Tone IMD Performance,
DATA = 150 MSPS, No Interpolation
Figure 28. Single-Tone Spurious Performance, fOUT = 10 MHz,
DATA = 80 MSPS, Interpolation = 4×
f
f
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
0
–20
–40
–60
–80
–100
0
50
100
150
200
250
300
0
5
10
15
20
25
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 26. Single-Tone Spurious Performance, fOUT = 10 MHz,
DATA = 150 MSPS, Interpolation = 2×
Figure 29. Two-Tone IMD Performance, fOUT = 10 MHz,
fDATA = 50 MSPS, Interpolation = 8×
f
Rev. C | Page 16 of 60
AD9777
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
0
100
200
300
400
0
20
40
60
80
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 30. Single-Tone Spurious Performance, fOUT = 10 MHz,
DATA = 50 MSPS, Interpolation = 8×
Figure 31. Eight-Tone IMD Performance, fDATA = 160 MSPS, Interpolation = 8x
f
Rev. C | Page 17 of 60
AD9777
MODE CONTROL (VIA SPI PORT)
Table 9. Mode Control via SPI Port1
Address Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
00h
01h
02h
SDIO
LSB, MSB First
0 = MSB
1 = LSB
Software
Reset on
Logic 1
Sleep Mode
Logic 1
Shuts Down
the DAC
Output
Currents
Power-Down
Mode Logic 1
Shuts Down All Current Set by
Digital and
Analog
Functions
1R/2R Mode
DAC Output
PLL_LOCK
Indicator
Bidirectional
0 = Input
1 = I/O
One or Two
External
Resistors
0 = 2R, 1 = 1R
Filter
Filter
Modulation Modulation
Mode
(None, fS/2,
fS/4, fS/8)
0 = No Zero
Stuffing on
Interpolation
Filters, Logic 1
Enables Zero
Stuffing
1 = Real Mix
Mode
0 = Complex
Mix Mode
0 = e−jωt
1 = e+jωt
DATACLK/
PLL_LOCK2
Select
0 =
PLL_LOCK
Interpolation Interpolation
Rate
(1×, 2×,
4×, 8×)
Mode
(None, fS/2,
fS/4, fS/8)
Rate
(1×, 2×,
4×, 8×)
1 =
DATACLK
0 = Signed
Input Data
1 =
0 = Two-Port
Mode
1 = One-Port
Mode
DATACLK
Driver
Strength
DATACLK
Invert
0 = No
Invert
1 = Invert
ONEPORTCLK
Invert
0 = No Invert
1 = Invert
IQSEL
Invert
0 = No
Invert
1 = Invert
Q First
0 = I First
1 = Q First
Unsigned
03h
04h
Data Rate2
Clock
Output
PLL Divide
(Prescaler)
Ratio
PLL Divide
(Prescaler)
Ratio
0 = PLL
0 = Automatic
Charge Pump
Control
PLL
PLL
PLL
OFF2
Charge
Pump
Control
Charge
Pump
Control
Charge
Pump
Control
1 = PLL ON
1 =
Programmable
05h
06h
07h
08h
IDAC
Fine Gain
Adjustment
IDAC
Fine Gain
Adjustment
IDAC
Fine Gain
Adjustment Adjustment
IDAC
Fine Gain
IDAC
Fine Gain
Adjustment
IDAC
Fine Gain
Adjustment
IDAC
Fine Gain
Adjustment Adjustment
IDAC
Fine Gain
IDAC
Coarse Gain
Adjustment
IDAC
Coarse Gain
Adjustment
IDAC IDAC
Coarse Gain Coarse Gain
Adjustment Adjustment
IDAC Offset
Adjustment
Bit 9
IDAC Offset
Adjustment
Bit 8
IDAC Offset IDAC Offset
Adjustment Adjustment
Bit 7
IDAC Offset
Adjustment
Bit 5
IDAC Offset
Adjustment
Bit 4
IDAC Offset IDAC Offset
Adjustment Adjustment
Bit 3
Bit 6
Bit 2
IDAC IOFFSET
Direction
0 = IOFFSET on
IOUTA
IDAC Offset IDAC Offset
Adjustment Adjustment
Bit 1
Bit 0
1 = IOFFSET on
I
OUTB
09h
QDAC
QDAC
QDAC
QDAC
QDAC
QDAC
QDAC
QDAC
Fine Gain
Adjustment
Fine Gain
Adjustment
Fine Gain
Adjustment Adjustment
Fine Gain
Fine Gain
Adjustment
Fine Gain
Adjustment
Fine Gain
Adjustment Adjustment
Fine Gain
Rev. C | Page 18 of 60
AD9777
Address Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0Ah
QDAC
QDAC
QDAC
QDAC
Coarse Gain
Adjustment
Coarse Gain
Adjustment
Coarse Gain Coarse Gain
Adjustment Adjustment
0Bh
0Ch
QDAC Offset QDAC Offset
QDAC
Offset
Adjustment Bit 6
Bit 7
QDAC Offset QDAC Offset
QDAC Offset
Adjustment
Bit 4
QDAC
Offset
QDAC
Offset
Adjustment
Bit 9
Adjustment
Bit 8
Adjustment
Adjustment
Bit 5
Adjustment Adjustment
Bit 3
Bit 2
QDAC IOFFSET
Direction
0 = IOFFSET on
IOUTA
QDAC
Offset
QDAC
Offset
Adjustment Adjustment
Bit 1
Bit 0
1 = IOFFSET on
IOUTB
0Dh
Version
Register
Version
Register
Version
Register
Version
Register
1 Default values are shown in bold.
2 For more information, see the Two Port Data Input Mode section.
Rev. C | Page 19 of 60
AD9777
Bit 3: Logic 1 enables zero stuffing mode for interpolation filters.
REGISTER DESCRIPTION
Address 00h
Bit 2: Default (1) enables the real mix mode. The I and Q data
channels are individually modulated by fS/2, fS/4, or fS/8 after
the interpolation filters. However, no complex modulation is
done. In the complex mix mode (Logic 0), the digital
modulators on the I and Q data channels are coupled to create a
digital complex modulator. When the AD9777 is applied in
conjunction with an external quadrature modulator, rejection
can be achieved of either the higher or lower frequency image
around the second IF frequency (that is, the LO of the analog
quadrature modulator external to the AD9777) according to the
bit value of Register 01h, Bit 1.
Bit 7: Logic 0 (default) causes the SPI_SDIO pin to act as an
input during the data transfer (Phase 2) of the communications
cycle. When set to 1, SPI_SDIO can act as an input or output,
depending on Bit 7 of the instruction byte.
Bit 6: Logic 0 (default). Determines the direction (LSB/MSB
first) of the communications and data transfer communications
cycles. Refer to the MSB/LSB Transfers section for more details.
Bit 5: Writing a 1 to this bit resets the registers to their default
values and restarts the chip. The RESET bit always reads back 0.
Register Address 00h bits are not cleared by this software reset.
However, a high level at the RESET pin forces all registers,
including those in Address 00h, to their default state.
Bit 1: Logic 0 (default) causes the complex modulation to be of
the form e−jωt, resulting in the rejection of the higher frequency
image when the AD9777 is used with an external quadrature
modulator. A Logic 1 causes the modulation to be of the form
e+jωt, which causes rejection of the lower frequency image.
Bit 4: Sleep Mode. A Logic 1 to this bit shuts down the DAC
output currents.
Bit 0: In two-port mode, a Logic 0 (default) causes Pin 8 to act
as a lock indicator for the internal PLL. A Logic 1 in this register
causes Pin 8 to act as a DATACLK. For more information, see
the Two Port Data Input Mode section.
Bit 3: Power-Down. Logic 1 shuts down all analog and digital
functions except for the SPI port.
Bit 2: 1R/2R Mode. The default (0) places the AD9777 in two
resistor mode. In this mode, the IREF currents for the I and Q
DAC references are set separately by the RSET resistors on
FSADJ2 and FSADJ1 (Pins 59 and 60). In 2R mode, assuming
the coarse gain setting is full scale and the fine gain setting is 0,
Address 02h
Bit 7: Logic 0 (default) causes data to be accepted on the inputs
as twos complement binary. Logic 1 causes data to be accepted
as straight binary.
I
FULLSCALE1 = 32 × VREF/FSADJ1 and IFULLSCALE2 = 32 ×
REF/FSADJ2. With this bit set to 1, the reference currents for
both I and Q DACs are controlled by a single resistor on Pin 60.
FULLSCALE in one resistor mode for both the I and Q DACs is half
V
Bit 6: Logic 0 (default) places the AD9777 in two-port mode. I
and Q data enters the AD9777 via Ports 1 and 2, respectively. A
Logic 1 places the AD9777 in one-port mode in which
interleaved I and Q data is applied to Port 1. See Table 8 for
detailed information on how to use the DATACLK/PLL_LOCK,
IQSEL, and ONEPORTCLK modes.
I
of what it would be in 2R mode, assuming all other conditions
(RSET, register settings) remain unchanged. The full-scale
current of each DAC can still be set to 20 mA by choosing a
resistor of half the value of the RSET value used in 2R mode.
Bit 5: DATACLK Driver Strength. With the internal PLL
disabled and this bit set to Logic 0, it is recommended that
DATACLK be buffered. When this bit is set to Logic 1,
DATACLK acts as a stronger driver capable of driving small
capacitive loads.
Bit 1: PLL_LOCK Indicator. When the PLL is enabled, reading
this bit gives the status of the PLL. A Logic 1 indicates the PLL
is locked. A Logic 0 indicates an unlocked state.
Address 01h
Bit 7, Bit 6: This is the filter interpolation rate according to the
following table.
Bit 4: Logic 0 (default). A value of 1 inverts DATACLK at Pin 8.
Bit 2: Logic 0 (default). A value of 1 inverts ONEPORTCLK
at Pin 32.
00
01
10
11
1×
2×
4×
8×
Bit 1: Logic 0 (default) causes IQSEL = 0 to direct input data to
the I channel, while IQSEL = 1 directs input data to the Q
channel.
Bit 5 and Bit 4: This is the modulation mode according to the
following table.
Bit 0: Logic 0 (default) defines IQ pairing as IQ, IQ…, while
programming a Logic 1 causes the pair ordering to
be QI, QI…
00
01
10
11
none
fS/2
fS/4
fS/8
Rev. C | Page 20 of 60
AD9777
Address 03h
Address 05h, 09h
Bit 7: This allows the data rate clock (divided down from the
DAC clock) to be output at either the DATACLK/PLL_LOCK
pin (Pin 8) or at the SPI_SDO pin (Pin 53). The default of 0 in
this register enables the data rate clock at DATACLK/
PLL_LOCK, while a 1 in this register causes the data rate clock
to be output at SPI_SDO. For more information, see the Two
Port Data Input Mode section.
Bit 7, Bit 6, Bit 5, Bit 4, Bit 3, Bit 2, Bit 1, and Bit 0: These bits
represent an 8-bit binary number (Bit 7 MSB) that defines the
fine gain adjustment of the I (05h) and Q (09h) DAC according
to Equation 1.
Address 06h, 0Ah
Bit 3, Bit 2, Bit 1, and Bit 0: These bits represent a 4-bit binary
number (Bit 3 MSB) that defines the coarse gain adjustment of
the I (06h) and Q (0Ah) DACs according to Equation 1.
Bit 1, Bit 0: Setting this divide ratio to a higher number allows
the VCO in the PLL to run at a high rate (for best performance)
while the DAC input and output clocks run substantially slower.
The divider ratio is set according to the following table.
Address 07h, 0Bh
Bit 7, Bit 6, Bit 5, Bit 4, Bit 3, Bit 2, Bit 1, and Bit 0: These bits
are used in conjunction with Address 08h, 0Ch, Bits 1, 0.
00
÷1
÷2
÷4
÷8
01
Address 08h, 0Ch
10
Bit 1 and Bit 0: The 10 bits from these two address pairs (07h,
08h and 0Bh, 0Ch) represent a 10-bit binary number that
defines the offset adjustment of the I and Q DACs according to
Equation 1. (07h, 0Bh–Bit 7 MSB/08h, 0Ch–Bit 0 LSB).
11
Address 04h
Bit 7: Logic 0 (default) disables the internal PLL. Logic 1
Address 08h, 0Ch
enables the PLL.
Bit 7: This bit determines the direction of the offset of the I
(08h) and Q (0Ch) DACs. A Logic 0 applies a positive offset
current to IOUTA, while a Logic 1 applies a positive offset current
to IOUTB. The magnitude of the offset current is defined by the
bits in Addresses 07h, 0Bh, 08h, 0Ch according to Equation 1.
Equation 1 shows IOUTA and IOUTB as a function of fine gain,
coarse gain, and offset adjustment when using 2R mode. In 1R
mode, the current IREF is created by a single FSADJ resistor
(Pin 60). This current is divided equally into each channel so that
a scaling factor of one-half must be added to these equations for
full-scale currents for both DACs and the offset.
Bit 6: Logic 0 (default) sets the charge pump control to
automatic. In this mode, the charge pump bias current is
controlled by the divider ratio defined in Address 03h, Bits 1
and 0. Logic 1 allows the user to manually define the charge
pump bias current using Address 04h, Bits 2, 1, and 0. Adjusting
the charge pump bias current allows the user to optimize the
noise/settling performance of the PLL.
Bit 2, Bit 1, Bit 0: With the charge pump control set to manual,
these bits define the charge pump bias current according to the
following table.
000
001
010
011
111
50 µA
100 µA
200 µA
400 µA
800 µA
6×I
COARSE +1
3×I
32
FINE
256
1024 DATA
⎡
⎢
⎤
⎡
⎤
⎥
⎛
⎜
⎝
⎞
⎟
⎠
⎛
⎞
⎟
⎛
⎜
⎝
⎞
⎟
⎠
⎛
⎜
⎝
⎞⎛
⎟⎜
⎠⎝
⎞
⎟
⎠
⎛
⎜
⎝
⎞
⎟
⎠
REF
REF
REF
IOUTA
=
=
−
−
×
(A)
⎜
216
⎥
⎦
⎢
⎣
8
16
24
⎝
⎠
⎦ ⎣
16
⎡
⎤
⎤
⎥
⎛
⎞
⎜
⎟
⎜
⎠
⎝
⎞
⎟
⎟
⎠
6×I
COARSE +1
3×I
32
FINE
256
1024
24
2
− DATA −1
⎡
⎛
⎜
⎝
⎞⎛
⎞
⎟
⎠
⎛
⎜
⎝
⎞⎛
⎟⎜
⎠⎝
⎞
⎟
⎠
⎛
⎢⎜
⎝
REF
IOUTB
×
⎥
(A)
(1)
⎜
⎟
216
⎢
⎣
8
16
⎠⎝
⎦ ⎢
⎥
⎦
⎣
OFFSET
1024
⎛
⎜
⎞
⎠
IOFFSET = 4×IREF
(A)
⎟
⎝
Rev. C | Page 21 of 60
AD9777
FUNCTIONAL DESCRIPTION
The AD9777 dual interpolating DAC consists of two data
channels that can be operated independently or coupled to form
a complex modulator in an image reject transmit architecture.
Each channel includes three FIR filters, making the AD9777
capable of 2×, 4×, or 8× interpolation. High speed input and
output data rates can be achieved within the following
limitations.
SDO (PIN 53)
SDIO (PIN 54)
AD9777 SPI PORT
INTERFACE
SPI_CLK (PIN 55)
CSB (PIN 56)
Figure 32. SPI Port Interface
Interpolation Rate
(MSPS)
Input Data Rate
(MSPS)
DAC Sample Rate
(MSPS)
SERIAL INTERFACE FOR REGISTER CONTROL
The AD9777 serial port is a flexible, synchronous serial
communications port that allows easy interface to many
industry-standard microcontrollers and microprocessors. The
serial I/O is compatible with most synchronous transfer
formats, including both the Motorola SPI® and Intel® SSR
protocols. The interface allows read/write access to all registers
that configure the AD9777. Single- or multiple-byte transfers
are supported as well as MSB first or LSB first transfer formats.
The AD9777’s serial interface port can be configured as a single
pin I/O (SDIO) or two unidirectional pins for I/O (SDIO/SDO).
1×
2×
4×
8×
160
160
100
50
160
320
400
400
Both data channels contain a digital modulator capable of
mixing the data stream with an LO of fDAC/2, fDAC/4, or fDAC/8,
where fDAC is the output data rate of the DAC. A zero stuffing
feature is also included and can be used to improve pass-band
flatness for signals being attenuated by the SIN(x)/x
characteristic of the DAC output. The speed of the AD9777,
combined with its digital modulation capability, enables direct
IF conversion architectures at 70 MHz and higher.
GENERAL OPERATION OF THE SERIAL INTERFACE
There are two phases to a communication cycle with the
AD9777. Phase 1 is the instruction cycle, which is the writing of
an instruction byte into the AD9777 coincident with the first
eight SCLK rising edges. The instruction byte provides the
AD9777 serial port controller with information regarding the
data transfer cycle, which is Phase 2 of the communication
cycle. The Phase 1 instruction byte defines whether the upcom-
ing data transfer is read or write, the number of bytes in the
data transfer, and the starting register address for the first byte
of the data transfer. The first eight SCLK rising edges of each
communication cycle are used to write the instruction byte into
the AD9777.
The digital modulators on the AD9777 can be coupled to form
a complex modulator. By using this feature with an external
analog quadrature modulator, such as the Analog Devices
AD8345, an image rejection architecture can be enabled. To
optimize the image rejection capability, as well as LO feed-
through in this architecture, the AD9777 offers programmable
(via the SPI port) gain and offset adjust for each DAC.
Also included on the AD9777 are a phase-locked loop (PLL)
clock multiplier and a 1.20 V band gap voltage reference. With
the PLL enabled, a clock applied to the CLK+/CLK− inputs is
frequency multiplied internally and generates all necessary
internal synchronization clocks. Each 16-bit DAC provides two
complementary current outputs whose full-scale currents can
be determined either from a single external resistor or inde-
pendently from two separate resistors (see the 1R/2R Mode
section). The AD9777 features a low jitter, differential clock
input that provides excellent noise rejection while accepting a
sine or square wave input. Separate voltage supply inputs are
provided for each functional block to ensure optimum noise
and distortion performance.
A Logic 1 on the SPI_CSB pin, followed by a logic low, resets
the SPI port timing to the initial state of the instruction cycle.
This is true regardless of the present state of the internal
registers or the other signal levels present at the inputs to the
SPI port. If the SPI port is in the middle of an instruction cycle
or a data transfer cycle, none of the present data is written.
The remaining SCLK edges are for Phase 2 of the
communication cycle. Phase 2 is the actual data transfer
between the AD9777 and the system controller. Phase 2 of the
communication cycle is a transfer of one to four data bytes, as
determined by the instruction byte. Normally, using one multi-
byte transfer is the preferred method. However, single byte data
transfers are useful to reduce CPU overhead when register
access requires one byte only. Registers change immediately
upon writing to the last bit of each transfer byte.
Sleep and power-down modes can be used to turn off the DAC
output current (sleep) or the entire digital and analog sections
(power-down) of the chip. A SPI-compliant serial port is used
to program the many features of the AD9777. Note that in
power-down mode, the SPI port is the only section of the chip
still active.
Rev. C | Page 22 of 60
AD9777
SPI_CSB (Pin 56)—Chip Select
INSTRUCTION BYTE
The instruction byte contains the information shown below.
Active low input starts and gates a communication cycle. It
allows more than one device to be used on the same serial
communications lines. The SPI_SDO and SPI_SDIO pins go to
a high impedance state when this input is high. Chip select
should stay low during the entire communication cycle.
N1
0
N0
0
Description
Transfer 1 Byte
Transfer 2 Bytes
Transfer 3 Bytes
Transfer 4 Bytes
0
1
1
0
1
1
SPI_SDIO (Pin 54)—Serial Data I/O
R/W
Data is always written into the AD9777 on this pin. However,
this pin can be used as a bidirectional data line. Bit 7 of Register
Address 00h controls the configuration of this pin. The default
is Logic 0, which configures the SPI_SDIO pin as
unidirectional.
Bit 7 of the instruction byte determines whether a read or a
write data transfer occurs after the instruction byte write. Logic
1 indicates read operation. Logic 0 indicates a write operation.
N1, N0
SPI_SDO (Pin 53)—Serial Data Out
Bit 6 and Bit 5 of the instruction byte determine the number of
bytes to be transferred during the data transfer cycle. The bit
decodes are shown in the following table.
Data is read from this pin for protocols that use separate lines
for transmitting and receiving data. In the case where the
AD9777 operates in a single bidirectional I/O mode, this pin
does not output data and is set to a high impedance state.
MSB
I7
LSB
I0
I6
I5
I4
I3
I2
I1
R/W
N1
N0
A4
A3
A2
A1
A0
MSB/LSB TRANSFERS
A4, A3, A2, A1, A0
The AD9777 serial port can support both most significant bit
(MSB) first or least significant bit (LSB) first data formats. This
functionality is controlled by the LSB first bit in Register 0. The
default is MSB first.
Bit 4, Bit 3, Bit 2, Bit 1, and Bit 0 of the instruction byte
determine which register is accessed during the data transfer
portion of the communications cycle. For multibyte transfers,
this address is the starting byte address. The remaining register
addresses are generated by the AD9777.
When this bit is set active high, the AD9777 serial port is in LSB
first format. In LSB first mode, the instruction byte and data
bytes must be written from LSB to MSB. In LSB first mode, the
serial port internal byte address generator increments for each
byte of the multibyte communication cycle.
SERIAL INTERFACE PORT PIN DESCRIPTIONS
SPI_CLK (Pin 55)—Serial Clock
The serial clock pin is used to synchronize data to and from the
AD9777 and to run the internal state machines. SPI_CLK
maximum frequency is 15 MHz. All data input to the AD9777
is registered on the rising edge of SPI_CLK. All data is driven
out of the AD9777 on the falling edge of SCLK.
When this bit is set default low, the AD9777 serial port is in
MSB first format. In MSB first mode, the instruction byte and
data bytes must be written from MSB to LSB. In MSB first
mode, the serial port internal byte address generator decre-
ments for each byte of the multibyte communication cycle.
When incrementing from 1Fh, the address generator changes to
00h. When decrementing from 00h, the address generator
changes to 1Fh.
Rev. C | Page 23 of 60
AD9777
INSTRUCTION CYCLE
DATA TRANSFER CYCLE
CS
SCLK
SDIO
R/W
I6
I5
I4
I3
I2
I1
I0
D7
D7
D6
D6
D2
D2
D1
D1
D0
D0
(N)
(N)
N
N
N
0
0
0
0
0
SDO
0
N
Figure 33. Serial Register Interface Timing MSB First
INSTRUCTION CYCLE
DATA TRANSFER CYCLE
CS
SCLK
SDIO
I0
I1
I2
I3
I4
I5
I6
R/W
D0
D0
D1
D1
D2
D6
D7
(N)
(N)
0
0
0
0
0
0
N
N
N
N
SDO
D2
D6
D7
Figure 34. Serial Register Interface Timing LSB First
tSCLK
tDS
CS
tPWH
tPWL
SCLK
SDIO
tDS
tDH
INSTRUCTION BIT 7
INSTRUCTION BIT 6
Figure 35. Timing Diagram for Register Write to AD9777
CS
SCLK
tDV
SDIO
SDO
DATA BIT N
DATA BIT N–1
Figure 36. Timing Diagram for Register Read from AD9777
Rev. C | Page 24 of 60
AD9777
The offset control defines a small current that can be added to
IOUTA or IOUTB (not both) on the IDAC and QDAC. The selection
of which IOUT this offset current is directed toward is program-
mable via Register 08h, Bit 7 (IDAC) and Register 0Ch, Bit 7
(QDAC). Figure 42 shows the scale of the offset current that can
be added to one of the complementary outputs on the IDAC
and QDAC. Offset control can be used for suppression of LO
leakage resulting from modulation of dc signal components. If
the AD9777 is dc-coupled to an external modulator, this feature
can be used to cancel the output offset on the AD9777 as well as
the input offset on the modulator. Figure 42 shows a typical
example of the effect that the offset control has on LO
suppression.
NOTES ON SERIAL PORT OPERATION
The AD9777 serial port configuration bits reside in Bit 6 and
Bit 7 of Register Address 00h. It is important to note that the
configuration changes immediately upon writing to the last bit
of the register. For multibyte transfers, writing to this register
may occur during the middle of the communication cycle. Care
must be taken to compensate for this new configuration for the
remaining bytes of the current communication cycle.
The same considerations apply to setting the reset bit in
Register Address 00h. All other registers are set to their default
values, but the software reset does not affect the bits in Register
Address 00h.
OFFSET
CONTROL
REGISTERS
It is recommended to use only single byte transfers when
changing serial port configurations or initiating a software
reset.
OFFSET
DAC
FINE
GAIN
DAC
GAIN
CONTROL
REGISTERS
FINE
GAIN
DAC
I
I
IDAC
OUTA1
A write to Bit 1, Bit 2, and Bit 3 of Address 00h with the same
logic levels as for Bit 7, Bit 6, and Bit 5 (bit pattern: XY1001YX
binary) allows the user to reprogram a lost serial port configu-
ration and to reset the registers to their default values. A second
write to Address 00h with reset bit low and serial port configu-
ration as specified above (XY) reprograms the OSC IN
1.2VREF
REFIO
0.1µF
OUTB1
COARSE COARSE
QDAC
I
I
OUTA2
GAIN
DAC
GAIN
DAC
OUTB2
FSADJ1
RSET1
OFFSET
CONTROL
REGISTERS
FSADJ2
OFFSET
DAC
multiplier setting. A changed fSYSCLK frequency is stable after a
maximum of 200 fMCLK cycles (equals wake-up time).
GAIN
CONTROL
RSET2
REGISTERS
Figure 37. DAC Outputs, Reference Current Scaling, and Gain/Offset Adjust
DAC OPERATION
The dual 16-bit DAC output of the AD9777, along with the
reference circuitry, gain, and offset registers, is shown in Figure
37 and Figure 38. Note that an external reference can be used by
simply overdriving the internal reference with the external
reference. Referring to the transfer functions in Equation 1, a
reference current is set by the internal 1.2 V reference, the
external RSET resistor, and the values in the coarse gain register.
The fine gain DAC subtracts a small amount from this and the
result is input to IDAC and QDAC, where it is scaled by an
amount equal to 1024/24. Figure 39 and Figure 40 show the
scaling effect of the coarse and fine adjust DACs. IDAC and
QDAC are PMOS current source arrays, segmented in a 5-4-7
configuration. The five MSB control an array of 31 current
sources. The next four bits consist of 15 current sources whose
values are all equal to 1/16 of an MSB current source. The 7
LSBs are binary weighted fractions of the middle bits’ current
AVDD
84µA
REFIO
7kΩ
0.7V
Figure 38. Internal Reference Equivalent Circuit
25
20
2R MODE
15
sources. All current sources are switched to either IOUTA or IOUTB
,
depending on the input code.
10
The fine adjustment of the gain of each channel allows for im-
proved balance of QAM modulated signals, resulting in improved
modulation accuracy and image rejection. In the Interfacing with
the AD8345 Quadrature Modulator section, the performance
data shows to what degree image rejection can be improved when
the AD9777 is used with an AD8345 quadrature modulator from
Analog Devices, Inc.
1R MODE
5
0
0
5
10
15
20
COARSE GAIN REGISTER CODE
(ASSUMING RSET1, RSET2 = 1.9kΩ)
Figure 39. Coarse Gain Effect on IFULLSCALE
Rev. C | Page 25 of 60
AD9777
0
–0.5
–1.0
–1.5
–2.0
–2.5
0
–10
–20
–30
–40
–50
–60
–70
–80
OFFSET REGISTER 1 ADJUSTED
1R MODE
2R MODE
OFFSET REGISTER 2
ADJUSTED, WITH OFFSET
REGISTER 1 SET
TO OPTIMIZED VALUE
–3.0
0
200
400
600
800
1000
–1024 –768
–512
–256
0
256
512
768
1024
FINE GAIN REGISTER CODE
(ASSUMING RSET1, RSET2 = 1.9k
DAC1, DAC2 (OFFSET REGISTER CODES)
Ω
)
Figure 42. Offset Adjust Control, Effect on LO Suppression
Figure 40. Fine Gain Effect on IFULLSCALE
1R/2R MODE
In Figure 42, the negative scale represents an offset added to
OUTB, while the positive scale represents an offset added to IOUTA
I
In 2R mode, the reference current for each channel is set
independently by the FSADJ resistor on that channel. The
AD9777 can be programmed to derive its reference current
from a single resistor on Pin 60 by putting the part into 1R
mode. The transfer functions in Equation 1 are valid for 2R
mode. In 1R mode, the current developed in the single FSADJ
resistor is split equally between the two channels. The result is
that in 1R mode, a scale factor of 1/2 must be applied to the
formulas in Equation 1. The full-scale DAC current in 1R mode
can still be set to as high as 20 mA by using the internal 1.2 V
reference and a 950 Ω resistor instead of the 1.9 kΩ resistor
typically used in 2R mode.
of the respective DAC. Offset Register 1 corresponds to IDAC,
while Offset Register 2 corresponds to QDAC. Figure 42
represents the AD9777 synthesizing a complex signal that is
then dc-coupled to an AD8345 quadrature modulator with an
LO of 800 MHz. The dc coupling allows the input offset of the
AD8345 to be calibrated out as well. The LO suppression at the
AD8345 output was optimized first by adjusting Offset
Register 1 in the AD9777. When an optimal point was found
(roughly Code 54), this code was held in Offset Register 1, and
Offset Register 2 was adjusted. The resulting LO suppression is
70 dBFS. These are typical numbers, and the specific code for
optimization varies from part to part.
CLOCK INPUT CONFIGURATION
5
4
3
The clock inputs to the AD9777 can be driven differentially or
single-ended. The internal clock circuitry has supply and
ground (CLKVDD, CLKGND) separate from the other supplies
on the chip to minimize jitter from internal noise sources.
Figure 43 shows the AD9777 driven from a single-ended clock
source. The CLK+/CLK− pins form a differential input
(CLKIN) so that the statically terminated input must be dc-
biased to the midswing voltage level of the clock driven input.
2R MODE
2
1R MODE
1
AD9777
R
SERIES
0
CLK+
0
200
400
600
800
1000
COARSE GAIN REGISTER CODE
(ASSUMING RSET1, RSET2 = 1.9kΩ)
CLKVDD
CLK–
Figure 41. DAC Output Offset Current
V
THRESHOLD
0.1µF
CLKGND
Figure 43. Single-Ended Clock Driving Clock Inputs
Rev. C | Page 26 of 60
AD9777
A configuration for differentially driving the clock inputs is
given in Figure 44. DC-blocking capacitors can be used to
couple a clock driver output whose voltage swings exceed
CLKVDD or CLKGND. If the driver voltage swings are within
the supply range of the AD9777, the dc-blocking capacitors and
bias resistors are not necessary.
PROGRAMMABLE PLL
CLKIN can function either as an input data rate clock (PLL
enabled) or as a DAC data rate clock (PLL disabled) according
to the state of Address 02h, Bit 7 in the SPI port register. The
internal operation of the AD9777 clock circuitry in these two
modes is illustrated in Figure 45 and Figure 46.
AD9777
The PLL clock multiplier and distribution circuitry produce the
necessary internal synchronized 1×, 2×, 4×, and 8× clocks for
the rising edge triggered latches, interpolation filters,
modulators, and DACs. This circuitry consists of a phase
detector, charge pump, voltage controlled oscillator (VCO),
prescaler, clock distribution, and SPI port control. The charge
pump, VCO, differential clock input buffer, phase detector,
prescaler, and clock distribution are all powered from
CLKVDD. PLL lock status is indicated by the logic signal at the
PLL_LOCK pin, as well as by the status of Bit 1, Register 00h.
To ensure optimum phase noise performance from the PLL
clock multiplier and distribution, CLKVDD should originate
from a clean analog supply. Table 10 defines the minimum
input data rates versus the interpolation and PLL divider
setting. If the input data rate drops below the defined minimum
under these conditions, VCO phase noise can increase
significantly. The VCO speed is a function of the input data
rate, the interpolation rate, and the VCO prescaler, according to
the following function:
1kΩ
0.1µF
CLK+
1kΩ
0.1µF
0.1µF
ECL/PECL
CLKVDD
CLK–
1kΩ
1kΩ
CLKGND
Figure 44. Differential Clock Driving Clock Inputs
A transformer, such as the T1-1T from Mini-Circuits, can also
be used to convert a single-ended clock to differential. This
method is used on the AD9777 evaluation board so that an
external sine wave with no dc offset can be used as a differential
clock.
PECL/ECL drivers require varying termination networks, the
details of which are left out of Figure 43 and Figure 44 but can
be found in application notes such as AND8020/D from On
Semiconductor. These networks depend on the assumed
transmission line impedance and power supply voltage of the
clock driver. Optimum performance of the AD9777 is achieved
when the driver is placed very close to the AD9777 clock inputs,
thereby negating any transmission line effects such as reflec-
tions due to mismatch.
VCO Speed (MHz) =
Input Data Rate (MHz)× Interpolation Rate × Prescaler
CLK+ CLK–
PLLVDD
PLL_LOCK
1 = LOCK
0 = NO LOCK
AD9777
The quality of the clock and data input signals is important in
achieving optimum performance. The external clock driver
circuitry should provide the AD9777 with a low jitter clock
input that meets the minimum/maximum logic levels while
providing fast edges. Although fast clock edges help minimize
any jitter that manifests itself as phase noise on a reconstructed
waveform, the high gain bandwidth product of the AD9777’s
clock input comparator can tolerate differential sine wave inputs
as low as 0.5 V p-p with minimal degradation of the output
noise floor.
INTERPOLATION
FILTERS,
MODULATORS,
AND DACS
PHASE
DETECTOR
CHARGE
PUMP
LPF
2
4
8
1
CLOCK
DISTRIBUTION
CIRCUITRY
PRESCALER
VCO
INPUT
DATA
LATCHES
PLL DIVIDER
(PRESCALER)
CONTROL
INTERNAL SPI
CONTROL
REGISTERS
INTERPOLATION
RATE
PLL
CONTROL
(PLL ON)
MODULATION
CONTROL
RATE
SPI PORT
CONTROL
Figure 45. PLL and Clock Circuitry with PLL Enabled
Rev. C | Page 27 of 60
AD9777
Table 11. Required PLL Prescaler Ration vs. fDATA
CLK+ CLK–
fDATA (MSPS)
PLL
Prescaler Ratio
PLL_LOCK
1 = LOCK
0 = NO LOCK
125
125
100
75
Disabled
Enabled
Enabled
Enabled
Enabled
AD9777
Div 1
Div 2
Div 2
Div 4
INTERPOLATION
FILTERS,
MODULATORS,
AND DACS
PHASE
DETECTOR
CHARGE
PUMP
50
2
4
8
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
1
CLOCK
DISTRIBUTION
CIRCUITRY
PRESCALER
VCO
INPUT
DATA
LATCHES
PLL DIVIDER
(PRESCALER)
CONTROL
INTERNAL SPI
CONTROL
REGISTERS
INTERPOLATION
RATE
PLL
CONTROL
(PLL ON)
MODULATION
RATE
CONTROL
CONTROL
SPI PORT
Figure 46. PLL and Clock Circuitry with PLL Disabled
In addition, if the zero stuffing option is enabled, the VCO doubles its
speed again. Phase noise can be slightly higher with the PLL enabled.
Figure 47 illustrates typical phase noise performance of the AD9777
with 2× interpolation and various input data rates. The signal
synthesized for the phase noise measurement was a single carrier at a
frequency of fDATA/4. The repetitive nature of this signal eliminates
quantization noise and distortion spurs as a factor in the measure-
ment. Although the curves blend in Figure 47, the different
conditions are given for clarity in the table preceding Figure 47.
Figure 47 also contains a table detailing PLL divider settings vs.
interpolation rate and maximum and minimum fDATA rates. Note that
maximum fDATA rates of 160 MSPS are due to the maximum input
data rate of the AD9777. However, maximum rates of less than 160
MSPS and all minimum fDATA rates are due to maximum and mini-
mum speeds of the internal PLL VCO. Figure 48 shows typical
performance of the PLL lock signal (Pin 8 or Pin 53) when the PLL is
in the process of locking.
–110
0
1
2
3
4
5
FREQUENCY OFFSET (MHz)
Figure 47. Phase Noise Performance
Table 10. PLL Optimization
Interpolation
Rate
Divider
Setting
Minimum
fDATA
Maximum
fDATA
Figure 48. PLL_LOCK Output Signal (Pin 8) in the Process of Locking
(Typical Lock Time)
1
1
1
1
2
2
2
2
4
4
4
4
8
8
8
8
1
2
4
8
1
2
4
8
1
2
4
8
1
2
4
8
32
16
8
160
160
112
56
160
112
56
28
100
56
28
14
50
28
14
7
It is important to note that the resistor/capacitor needed for the
PLL loop filter is internal on the AD9777. This suffices unless
the input data rate is below 10 MHz, in which case an external
series RC is required between the LPF and CLKVDD pins.
4
24
12
6
3
24
12
6
3
24
12
6
3
Rev. C | Page 28 of 60
AD9777
35
30
25
20
15
10
5
POWER DISSIPATION
8×
The AD9777 has three voltage supplies: DVDD, AVDD, and
CLKVDD. Figure 49, Figure 50, and Figure 51 show the current
required from each of these supplies when each is set to the
3.3 V nominal specified for the AD9777. Power dissipation (PD)
can easily be extracted by multiplying the given curves by 3.3.
As Figure 49 shows, IDVDD is very dependent on the input data
rate, the interpolation rate, and the activation of the internal
digital modulator. IDVDD, however, is relatively insensitive to the
modulation rate by itself. In Figure 50, IAVDD shows the same
type of sensitivity to data, interpolation rate, and the modulator
function but to a much lesser degree (<10ꢀ). In Figure 51,
ICLKVDD varies over a wide range yet is responsible for only a
small percentage of the overall AD9777 supply current
requirement.
4×
2×
1×
0
0
50
100
150
200
fDATA (MHz)
Figure 51. ICLKVDD vs. fDATA vs. Interpolation Rate, PLL Disabled
400
SLEEP/POWER-DOWN MODES
8×, (MOD. ON)
2×, (MOD. ON)
350
300
250
200
150
100
50
(Control Register 00h, Bit 3 and Bit 4)
4×, (MOD. ON)
The AD9777 provides two methods for programmable
reduction in power savings. The sleep mode, when activated,
turns off the DAC output currents but the rest of the chip
remains functioning. When coming out of sleep mode, the
AD9777 immediately returns to full operation. Power-down
mode, on the other hand, turns off all analog and digital
circuitry in the AD9777 except for the SPI port. When
returning from power-down mode, enough clock cycles must
be allowed to flush the digital filters of random data acquired
during the power-down cycle. Note that optimal performance
with the PLL enabled is achieved with the UCO in the PLL
control loop running at 450 MHz to 550 MHz.
8×
4×
2×
1×
0
0
50
100
150
200
fDATA (MHz)
Figure 49. IDVDD vs. fDATA vs. Interpolation Rate, PLL Disabled
TWO PORT DATA INPUT MODE
76.0
75.5
75.0
74.5
74.0
73.5
73.0
72.5
72.0
4×, (MOD. ON)
8×, (MOD. ON)
The digital data input ports can be configured as two
independent ports or as a single (one-port mode) port. In the
two-port mode, data at the two input ports is latched into the
AD9777 on every rising edge of the data rate clock (DATACLK).
In addition, in the two-port mode, the AD9777 can be
programmed to generate an externally available DATACLK for
the purpose of data synchronization. This data rate clock can be
programmed to be available at either Pin 8 (DATACLK/
PLL_LOCK) or Pin 53 (SPI_SDO). Because Pin 8 can also
function as a PLL lock indicator when the PLL is enabled, there
are several options for configuring Pin 8 and Pin 53. The
following information describes these options.
2×, (MOD. ON)
4×
8×
2×
1×
0
50
100
fDATA (MHz)
150
200
PLL Off (Register 4, Bit 7 = 0)
Figure 50. IAVDD vs. fDATA vs. Interpolation Rate, PLL Disabled
Register 3, Bit 7 = 0; DATACLK out of Pin 8.
Register 3, Bit 7 = 1; DATACLK out of Pin 53.
PLL On (Register 4, Bit 7 = 1)
Register 3, Bit 7 = 0, Register 1, Bit 0 = 0; PLL lock indicator out
of Pin 8.
Rev. C | Page 29 of 60
AD9777
tOD
Register 3, Bit 7 = 1, Register 1, Bit 0 = 0; PLL lock indicator out
of Pin 53.
Register 3, Bit 7 = 0, Register 1, Bit 0 = 1; DATACLK out of Pin 8.
Register 3, Bit 7 = 1, Register 1, Bit 0 = 1; DATACLK out of Pin 53.
CLKIN
In one-port mode, P2B14 and P2B15 from input data port two
are redefined as IQSEL and ONEPORTCLK, respectively. The
input data in one-port mode is steered to one of the two inter-
nal data channels based on the logic level of IQSEL. A clock
signal, ONEPORTCLK, is generated by the AD9777 in this
mode for the purpose of data synchronization. ONEPORTCLK
runs at the input interleaved data rate, which is 2× the data rate
at the internal input to either channel.
DATACLK
DATA AT PORTS
1 AND 2
tS = 0.0ns (MAX)
tH = 2.5ns (MAX)
Test configurations showing the various clocks that are required
and generated by the AD9777 with the PLL enabled/disabled
and in the one-port/two-port modes are given in Figure 101 to
Figure 104. Jumper positions needed to operate the AD9777
evaluation board in these modes are given as well.
tS tH
Figure 52. Timing Requirements in Two-Port Input Mode with PLL Enabled
DATACLK DRIVER STRENGTH
(Control Register 02h, Bit 5)
PLL ENABLED, TWO-PORT MODE
The DATACLK output driver strength is capable of driving
>10 mA into a 330 Ω load while providing a rise time of 3 ns.
Figure 53 shows DATACLK driving a 330 Ω resistive load at a
frequency of 50 MHz. By enabling the drive strength option
(Control Register 02h, Bit 5), the amplitude of DATACLK under
these conditions increases by approximately 200 mV.
(Control Register 02h, Bits 6 to 0 and 04h, Bits 7 to 1)
With the phase-locked loop (PLL) enabled and the AD9777 in
two-port mode, the speed of CLKIN is inherently that of the
input data rate. In two-port mode, Pin 8 (DATACLK/PLL_
LOCK) can be programmed (Control Register 01h, Bit 0) to
function as either a lock indicator for the internal PLL or as a
clock running at the input data rate. When Pin 8 is used as a
clock output (DATACLK), its frequency is equal to that of
CLKIN. Data at the input ports is latched into the AD9777 on
3.0
2.5
2.0
1.5
1.0
0.5
the rising edge of the CLKIN. Figure 52 shows the delay, tOD
,
inherent between the rising edge of CLKIN and the rising edge
of DATACLK, as well as the setup and hold requirements for
the data at Ports 1 and 2. The setup and hold times given in Figure
52 are the input data transitions with respect to CLKIN. Note
that in two-port mode (PLL enabled or disabled), the data rate
at the interpolation filter inputs is the same as the input data
rate at Port 1 and Port 2.
0
DELTA APPROX. 2.8ns
–0.5
The DAC output sample rate in two-port mode is equal to the
clock input rate multiplied by the interpolation rate. If zero
stuffing is used, another factor of 2 must be included to
calculate the DAC sample rate.
0
10
20
30
40
50
TIME (ns)
Figure 53. DATACLK Driver Capability into 330 Ω at 50 MHz
PLL ENABLED, ONE-PORT MODE
DATACLK INVERSION
(Control Register 02h, Bits 6 to 1 and 04h, Bits 7 to 1)
(Control Register 02h, Bit 4)
In one-port mode, the I and Q channels receive their data from
an interleaved stream at digital input Port 1. The function of
Pin 32 is defined as an output (ONEPORTCLK) that generates a
clock at the interleaved data rate, which is 2× the internal input
data rate of the I and Q channels. The frequency of CLKIN is
equal to the internal input data rate of the I and Q channels.
By programming this bit, the DATACLK signal shown in Figure 53
can be inverted. With inversion enabled, tOD refers to the time
between the rising edge of CLKIN and the falling edge of
DATACLK. No other effect on timing occurs.
Rev. C | Page 30 of 60
AD9777
IQ PAIRING
The selection of the data for the I or Q channel is determined by
the state of the logic level at Pin 31 (IQSEL when the AD9777 is
in one-port mode) on the rising edge of ONEPORTCLK.
(Control Register 02h, Bit 0)
In one-port mode, the interleaved data is latched into the
AD9777 internal I and Q channels in pairs. The order of how
the pairs are latched internally is defined by this control register.
The following is an example of the effect this has on incoming
interleaved data.
Under these conditions, IQSEL = 0 latches the data into the I
channel on the clock rising edge, while IQSEL = 1 latches the
data into the Q channel. It is possible to invert the I and Q
selection by setting Control Register 02h, Bit 1 to the invert
state (Logic 1). Figure 54 illustrates the timing requirements for
the data inputs as well as the IQSEL input. Note that the 1×
interpolation rate is not available in one-port mode.
Given the following interleaved data stream, where the data
indicates the value with respect to full scale:
I
Q
0.5
I
1
Q
1
I
Q
0.5
I
0
Q
0
I
Q
0.5
The DAC output sample rate in one-port mode is equal to
CLKIN multiplied by the interpolation rate. If zero stuffing is
used, another factor of 2 must be included to calculate the DAC
sample rate.
0.5
0.5
0.5
With the control register set to 0 (I first), the data appears at the
internal channel inputs in the following order in time:
I Channel
Q Channel
0.5
0.5
1
1
0.5
0.5
0
0
0.5
0.5
ONEPORTCLK INVERSION
(Control Register 02h, Bit 2)
With the control register set to 1 (Q first), the data appears at
the internal channel inputs in the following order in time:
By programming this bit, the ONEPORTCLK signal shown in
Figure 54 can be inverted. With inversion enabled, tOD refers to
the delay between the rising edge of the external clock and the
falling edge of ONEPORTCLK. The setup and hold times, tS
and tH, are with respect to the falling edge of ONEPORTCLK.
There is no other effect on timing.
I Channel
Q Channel
0.5
y
1
0.5
0.5
1
0
0.5
0.5
0
x
0.5
The values x and y represent the next I value and the previous Q
value in the series.
PLL DISABLED, TWO-PORT MODE
ONEPORTCLK DRIVER STRENGTH
With the PLL disabled, a clock at the DAC output rate must be
applied to CLKIN. Internal clock dividers in the AD9777 syn-
thesize the DATACLK signal at Pin 8, which runs at the input
data rate and can be used to synchronize the input data. Data is
latched into input Port 1 and Port 2 of the AD9777 on the rising
edge of DATACLK. DATACLK speed is defined as the speed of
CLKIN divided by the interpolation rate. With zero stuffing en-
abled, this division increases by a factor of 2. Figure 55 illustrates
the delay between the rising edge of CLKIN and the rising edge
of DATACLK, as well as tS and tH in this mode.
The drive capability of ONEPORTCLK is identical to that of
DATACLK in the two-port mode. Refer to Figure 53 for
performance under load conditions.
tOD
tOD = 4.0ns (MIN)
TO 5.5ns (MAX)
CLKIN
tS = 3.0ns (MAX)
tH = –0.5ns (MAX)
tIQS = 3.5ns (MAX)
tIQH = –1.5ns (MAX
ONEPORTCLK
The programmable modes DATACLK inversion and DATACLK
driver strength described in the PLL Enabled, Two-Port Mode
section have identical functionality with the PLL disabled.
The data rate CLK created by dividing down the DAC clock in
this mode can be programmed (via Register x03h, Bit 7) to be
output from the SPI_SDO pin, rather than the DATACLK pin.
In some applications, this may improve complex image rejec-
tion. tOD increases by 1.6 ns when SPI_SDO is used as data rate
clock out.
I AND Q INTERLEAVED
INPUT DATA AT PORT 1
tS tH
IQSEL
tIQS
tIQH
Figure 54. Timing Requirements in One-Port
Input Mode, with the PLL Enabled
Rev. C | Page 31 of 60
AD9777
tOD
tOD
CLKIN
CLKIN
DATACLK
ONEPORTCLK
DATA AT PORTS
1 AND 2
I AND Q INTERLEAVED
INPUT DATA AT PORT 1
tOD = 6.5ns (MIN) TO 8.0ns (MAX)
tS = 5.0ns (MAX)
tH = –3.2ns (MAX)
tS
tH
Figure 55. Timing Requirements in Two-Port Input Mode, with PLL Disabled
tS tH
PLL DISABLED, ONE-PORT MODE
IQSEL
tOD = 4.0ns (MIN)
TO 5.5ns (MAX)
tOD = 4.7ns (MAX)
tS = 3.0ns (MAX)
tH = –1.0ns (MAX)
tIQS = 3.5ns (MAX)
tIQH = –1.5ns (MAX)
(TYP SPECS)
In one-port mode, data is received into the AD9777 as an
interleaved stream on Port 1. A clock signal (ONEPORTCLK),
running at the interleaved data rate, which is 2× the input data
rate of the internal I and Q channels, is available for data
synchronization at Pin 32.
tIQS
tIQH
Figure 56. Timing Requirements in One-Port Input Mode, with PLL Disabled
With PLL disabled, a clock at the DAC output rate must be applied
to CLKIN. Internal dividers synthesize the ONEPORTCLK signal
at Pin 32. The selection of the data for the I or Q channel is deter-
mined by the state of the logic level applied to Pin 31 (IQSEL when
the AD9777 is in one-port mode) on the rising edge of
ONEPORTCLK. Under these conditions, IQSEL = 0 latches the
data into the I channel on the clock rising edge, while IQSEL = 1
latches the data into the Q channel. It is possible to invert the I and
Q selection by setting Control Register 02h, Bit 1 to the invert state
(Logic 1). Figure 56 illustrates the timing requirements for the data
inputs as well as the IQSEL input. Note that the 1× interpolation
rate is not available in the one-port mode.
DIGITAL FILTER MODES
The I and Q data paths of the AD9777 have their own
independent half-band FIR filters. Each data path consists of
three FIR filters, providing up to 8× interpolation for each
channel. The rate of interpolation is determined by the state of
Control Register 01h, Bit 7 and Bit 6. Figure 2 to Figure 4 show
the response of the digital filters when the AD9777 is set to 2×,
4×, and 8× modes. The frequency axes of these graphs have
been normalized to the input data rate of the DAC. As the
graphs show, the digital filters can provide greater than 75 dB of
out-of-band rejection.
An online tool is available for quick and easy analysis of the
AD9777 interpolation filters in the various modes. The link can be
accessed at http://www.analog.com/Analog_Root/static/
techsupport/designtools/interactiveTools/dac/ad9777image.html.
One-port mode is very useful when interfacing with devices,
such as the Analog Devices AD6622 or AD6623 transmit signal
processors, in which two digital data channels have been inter-
leaved (multiplexed). The programmable modes’ ONEPORTCLK
inversion, ONEPORTCLK driver strength, and IQ pairing
described in the PLL Enabled, One-Port Mode section have
identical functionality with the PLL disable.
AMPLITUDE MODULATION
Given two sine waves at the same frequency but with a 90°
phase difference, a point of view in time can be taken such that
the waveform that leads in phase is cosinusoidal and the
waveform that lags is sinusoidal. Analysis of complex variables
states that the cosine waveform can be defined as having real
positive and negative frequency components, while the sine
waveform consists of imaginary positive and negative frequency
images. This is shown graphically in the frequency domain in
Figure 57.
Rev. C | Page 32 of 60
AD9777
–jωt
e /2j
The phase relationship of the modulated signals is dependent
on whether the modulating carrier is sinusoidal or cosinusoidal,
again with respect to the reference point of the viewer.
SINE
DC
–jωt
e
/2j
Examples of sine and cosine modulation are given in Figure 58.
–jωt
Ae
/2j
–jωt
/2
–jωt
e
e
/2
SINUSOIDAL
MODULATION
COSINE
DC
DC
–jωt
–jωt
Figure 57. Real and Imaginary Components of
Sinusoidal and Cosinusoidal Waveforms
Ae
Ae
/2j
/2
–jωt
Ae
/2
COSINUSOIDAL
MODULATION
Amplitude modulating a baseband signal with a sine or a cosine
convolves the baseband signal with the modulating carrier in
the frequency domain. Amplitude scaling of the modulated
signal reduces the positive and negative frequency images by a
factor of 2. This scaling is very important in the discussion of
the various modulation modes.
DC
Figure 58. Baseband Signal, Amplitude Modulated with Sine and Cosine Carriers
Rev. C | Page 33 of 60
AD9777
By comparing the digital domain spectrum to the DAC
SIN(x)/x roll-off, an estimate can be made for the characteris-
tics required for the DAC reconstruction filter. Note also, per
the previous discussion on amplitude modulation, that the
spectral components (where modulation is set to fS/4 or fS/8) are
scaled by a factor of 2. In the situation where the modulation is
fS/2, the modulated spectral components add constructively,
and there is no scaling effect.
MODULATION, NO INTERPOLATION
With Control Register 01h, Bit 7 and Bit 6 set to 00, the
interpolation function on the AD9777 is disabled. Figure 59 to
Figure 62 show the DAC output spectral characteristics of the
AD9777 in the various modulation modes, all with the
interpolation filters disabled. The modulation frequency is
determined by the state of Control Register 01h, Bits 5 and 4.
The tall rectangles represent the digital domain spectrum of a
baseband signal of narrow bandwidth.
The Effects of Digital Modulation on DAC Output Spectrum, Interpolation Disabled
0
0
–20
–20
–40
–60
–80
–40
–60
–80
–100
–100
0
0.2
0.4
0.6
0.8
1.0
0
0.2
0.4
0.6
0.8
1.0
fOUT
(×
fDATA
)
fOUT
(×fDATA)
Figure 59. No Interpolation, Modulation Disabled
Figure 61. No Interpolation, Modulation = fDAC/4
0
–20
–40
0
–20
–40
–60
–60
–80
–80
–100
–100
0
0.2
0.4
0.6
0.8
1.0
0
0.2
0.4
0.6
0.8
1.0
fOUT
(×fDATA)
fOUT
(×fDATA)
Figure 60. No Interpolation, Modulation = fDAC/2
Figure 62. No Interpolation, Modulation = fDAC/8
Rev. C | Page 34 of 60
AD9777
For this reason, as Figure 63 to Figure 66 show, the pass band of
the interpolation filters can be frequency shifted, giving the
equivalent of a high-pass digital filter.
MODULATION, INTERPOLATION = 2×
With Control Register 01h, Bit 7 and Bit 6 set to 01, the
interpolation rate of the AD9777 is 2×. Modulation is achieved
by multiplying successive samples at the interpolation filter
output by the sequence (+1, −1). Figure 63 to Figure 66
represent the spectral response of the AD9777 DAC output with
2× interpolation in the various modulation modes to a narrow
band baseband signal (again, the tall rectangles in the graphic).
The advantage of interpolation becomes clear in Figure 63 to
Figure 66, where it can be seen that the images that would
normally appear in the spectrum around the significant point is
that the interpolation filtering is done prior to the digital
modulator.
Note that when using the fS/4 modulation mode, there is no
true stop band as the band edges coincide with each other. In
the fS/8 modulation mode, amplitude scaling occurs over only a
portion of the digital filter pass band due to constructive
addition over just that section of the band
The Effects of Digital Modulation on DAC Output Spectrum, Interpolation = 2x
0
0
–20
–20
–40
–60
–80
–40
–60
–80
–100
–100
0
0.5
1.0
1.5
2.0
0
0.5
1.0
1.5
2.0
fOUT
(×
fDATA
)
fOUT
(×fDATA)
Figure 63. 2× Interpolation, Modulation = Disabled
Figure 65. 2× Interpolation, Modulation = fDAC/4
0
0
–20
–20
–40
–60
–80
–40
–60
–80
–100
–100
0
0.5
1.0
1.5
2.0
0
0.5
1.0
1.5
2.0
fOUT
(×fDATA)
fOUT
(×fDATA)
Figure 64. 2× Interpolation, Modulation = fDAC/2
Figure 66. 2× Interpolation, Modulation = fDAC/8
Rev. C | Page 35 of 60
AD9777
Figure 67 to Figure 70 represent the spectral response of the
AD9777 DAC output with 4× interpolation in the various
modulation modes to a narrow band baseband signal.
MODULATION, INTERMODULATION = 4×
With Control Register 01h, Bit 7 and Bit 6 set to 10, the
interpolation rate of the AD9777 is 4×. Modulation is achieved
by multiplying successive samples at the interpolation filter
output by the sequence (0, +1, 0, −1).
The Effects of Digital Modulation on DAC Output Spectrum, Interpolation = 4x
0
0
–20
–20
–40
–60
–80
–40
–60
–80
–100
–100
0
1
2
3
4
0
1
2
3
4
fOUT
(×
fDATA
)
fOUT
(×fDATA)
Figure 67. 4x Interpolation, Modulation Disabled
Figure 69. 4x Interpolation, Modulation = fDAC/4
0
0
–20
–20
–40
–60
–80
–40
–60
–80
–100
–100
0
1
2
3
4
0
1
2
3
4
fOUT
(×
fDATA
)
fOUT
(×fDATA)
Figure 68. 4x Interpolation, Modulation = fDAC/2
Figure 70. 4x Interpolation, Modulation = fDAC/8
Rev. C | Page 36 of 60
AD9777
Looking at Figure 59 to Figure 75, the user can see how higher
interpolation rates reduce the complexity of the reconstruction
filter needed at the DAC output. It also becomes apparent that
the ability to modulate by fS/2, fS/4, or fS/8 adds a degree of
flexibility in frequency planning
MODULATION, INTERMODULATION = 8×
With Control Register 01h, Bits 7 and 6, set to 11, the
interpolation rate of the AD9777 is 8×. Modulation is achieved
by multiplying successive samples at the interpolation filter
output by the sequence (0, +0.707, +1, +0.707, 0, –0.707, −1,
+0.707). Figure 71 to Figure 74 represent the spectral response
of the AD9777 DAC output with 8× interpolation in the various
modulation modes to a narrow band baseband signal.
The Effects of the Digital Modulation on the DAC Output Spectrum, Interpolation = 8×
0
0
–20
–20
–40
–60
–40
–60
–80
–80
–100
–100
0
1
2
3
4
5
6
7
8
0
1
2
3
4
fOUT (×fDATA
)
fOUT
(×fDATA)
Figure 73. 8x Interpolation, Modulation = fDAC/4
Figure 71. 8× Interpolation, Modulation Disabled
0
0
–20
–20
–40
–60
–40
–60
–80
–80
–100
–100
0
1
2
3
4
5
6
7
8
0
1
2
3
4
fOUT
(×fDATA)
fOUT
(×fDATA)
Figure 74. 8x Interpolation, Modulation = fDAC/8
Figure 72. 8x Interpolation, Modulation = fDAC/2
Rev. C | Page 37 of 60
AD9777
The net effect is to increase the DAC output sample rate by a
factor of 2× with the 0 in the SIN(x)/x DAC transfer function
occurring at twice the original frequency. A 6 dB loss in
amplitude at low frequencies is also evident, as can be seen in
Figure 76.
ZERO STUFFING
(Control Register 01h, Bit 3)
As shown in Figure 75, a 0 or null in the output frequency
response of the DAC (after interpolation, modulation, and DAC
reconstruction) occurs at the final DAC sample rate (fDAC). This
is due to the inherent SIN(x)/x roll-off response in the digital-
to-analog conversion. In applications where the desired fre-
quency content is below fDAC/2, this may not be a problem. Note
that at fDAC/2 the loss due to SIN(x)/x is 4 dB. In direct RF appli-
cations, this roll-off may be problematic due to the increased
pass-band amplitude variation as well as the reduced amplitude
of the desired signal.
It is important to realize that the zero stuffing option by itself
does not change the location of the images but rather their
amplitude, pass-band flatness, and relative weighting. For
instance, in the previous example, the pass-band amplitude
flatness of the image at 3× fDATA/4 is now improved to 0.59 dB
while the signal level has increased slightly from −10.5 dBFS to
–8.1 dBFS.
INTERPOLATING (COMPLEX MIX MODE)
Consider an application where the digital data into the AD9777
represents a baseband signal around fDAC/4 with a pass band of
fDAC/10. The reconstructed signal out of the AD9777 would
experience only a 0.75 dB amplitude variation over its pass
band. However, the image of the same signal occurring at 3×
fDAC/4 suffers from a pass-band flatness variation of 3.93 dB.
This image may be the desired signal in an IF application using
one of the various modulation modes in the AD9777. This roll-
off of image frequencies can be seen in Figure 59 to Figure 74,
where the effect of the interpolation and modulation rate is
apparent as well.
(Control Register 01h, Bit 2)
In the complex mix mode, the two digital modulators on the
AD9777 are coupled to provide a complex modulation function.
In conjunction with an external quadrature modulator, this
complex modulation can be used to realize a transmit image
rejection architecture. The complex modulation function can be
programmed for e+jωt or e−jωt to give upper or lower image
rejection. As in the real modulation mode, the modulation
frequency ω can be programmed via the SPI port for fDAC/2,
fDAC/4, and fDAC/8, where fDAC represents the DAC output rate.
10
OPERATIONS ON COMPLEX SIGNALS
ZERO STUFFING
ENABLED
Truly complex signals cannot be realized outside of a computer
simulation. However, two data channels, both consisting of real
data, can be defined as the real and imaginary components of a
complex signal. I (real) and Q (imaginary) data paths are often
defined this way. By using the architecture defined in Figure 76,
a system that operates on complex signals can be realized,
giving a complex (real and imaginary) output.
0
–10
–20
ZERO STUFFING
–30
DISABLED
If a complex modulation function (e+jωt) is desired, the real and
imaginary components of the system correspond to the real and
imaginary components of e+jωt or cosωt and sinωt. As Figure 77
shows, the complex modulation function can be realized by
applying these components to the structure of the complex
system defined in Figure 76.
–40
–50
0
0.5
1.0
1.5
2.0
fOUT, NORMALIZED TO fDATA WITH ZERO STUFFING DISABLED (Hz)
Figure 75. Effect of Zero Stuffing on DAC’s SIN(x)/x Response
To improve upon the pass-band flatness of the desired image,
the zero stuffing mode can be enabled by setting the control
register bit to a Logic 1. This option increases the ratio of
fDAC/fDATA by a factor of 2 by doubling the DAC sample rate and
inserting a midscale sample (that is, 1000 0000 0000 0000) after
every data sample originating from the interpolation filter. This
is important as it affects the PLL divider ratio needed to keep
the VCO within its optimum speed range. Note that the zero
stuffing takes place in the digital signal chain at the output of
the digital modulator, before the DAC.
a(t)
c(t) × b(t) + d × b(t)
INPUT
OUTPUT
COMPLEX FILTER
= (c + jd)
IMAGINARY
INPUT
b(t)
OUTPUT
b(t) × a(t) + c × b(t)
Figure 76. Realization of a Complex System
Rev. C | Page 38 of 60
AD9777
INPUT
INPUT
(REAL)
(REAL)
OUTPUT
(REAL)
OUTPUT
INPUT
(IMAGINARY)
INPUT
(IMAGINARY)
SINωt
90°
90°
COSωt
Figure 78. Quadrature Modulation
OUTPUT
(IMAGINARY)
The entire upconversion from baseband to transmit frequency
is represented graphically in Figure 79. The resulting spectrum
shown in Figure 79 represents the complex data consisting of
the baseband real and imaginary channels, now modulated onto
orthogonal (cosine and negative sine) carriers at the transmit
frequency. It is important to remember that in this application
(two baseband data channels), the image rejection is not
dependent on the data at either of the AD9777 input channels.
–jωt
e
= COSωt + jSINωt
Figure 77. Implementation of a Complex Modulator
COMPLEX MODULATION AND IMAGE REJECTION
OF BASEBAND SIGNALS
In traditional transmit applications, a two-step upconversion is
done in which a baseband signal is modulated by one carrier to
an IF (intermediate frequency) and then modulated a second
time to the transmit frequency. Although this approach has
several benefits, a major drawback is that two images are created
near the transmit frequency. Only one image is needed, the other
being an exact duplicate. Unless the unwanted image is filtered,
typically with analog components, transmit power is wasted and
the usable bandwidth available in the system is reduced.
In fact, image rejection still occurs with either one or both of
the AD9777 input channels active. Note that by changing the
sign of the sinusoidal multiplying term in the complex
modulator, the upper sideband image could have been
suppressed while passing the lower one. This is easily done in
the AD9777 by selecting the e+jωt bit (Register 01h, Bit 1). In
purely complex terms, Figure 79 represents the two-stage
upconversion from complex baseband to carrier.
A more efficient method of suppressing the unwanted image
can be achieved by using a complex modulator followed by a
quadrature modulator. Figure 78 is a block diagram of a
quadrature modulator. Note that it is in fact the real output half
of a complex modulator. The complete upconversion can
actually be referred to as two complex upconversion stages, the
real output of which becomes the transmitted signal.
Rev. C | Page 39 of 60
AD9777
REAL CHANNEL (OUT)
A/2 A/2
1
–F
F
C
C
REAL CHANNEL (IN)
A
–B/2J
B/2J
DC
–F
C
F
C
COMPLEX
MODULATOR
TO QUADRATURE
MODULATOR
IMAGINARY CHANNEL (OUT)
–A/2J A/2J
IMAGINARY CHANNEL (IN)
–F
–F
C
C
B
DC
B/2
B/2
–F
F
C
C
A/4 + B/4J A/4 – B/4J
A/4 + B/4J A/4 – B/4J
2
–F
F
Q
Q
–F – F
–F + F
F
– F
F + F
Q C
Q
C
Q
C
Q
C
OUT
REAL
–A/4 – B/4J A/4 – B/4J
A/4 + B/4J –A/4 + B/4J
QUADRATURE
MODULATOR
–F
Q
F
Q
IMAGINARY
REJECTED IMAGES
A/2 + B/2J
A/2 – B/2J
–F
Q
F
Q
1
2
F
F
= COMPLEX MODULATION FREQUENCY
= QUADRATURE MODULATION FREQUENCY
C
Q
Figure 79. Two-Stage Upconversion and Resulting Image Rejection
Rev. C | Page 40 of 60
AD9777
COMPLEX BASEBAND
SIGNAL
A system in which multiple baseband signals are complex
modulated and then applied to the AD9777 real and imaginary
inputs, followed by a quadrature modulator, is shown in Figure 82,
which also describes the transfer function of this system and the
spectral output. Note the similarity of the transfer functions
given in Figure 82 and Figure 80. Figure 82 adds an additional
complex modulator stage for summing multiple carriers at the
AD9777 inputs. In addition, as in Figure 79, the image rejection
is not dependent on the real or imaginary baseband data on any
channel. Image rejection on a channel occurs if either the real
or imaginary data, or both, is present on the baseband channel.
1
j(ω1 + ω2)t
×
OUTPUT = REAL
1/2
e
1/2
= REAL
–ω1 – ω2
DC
ω1 + ω2
FREQUENCY
Figure 80. Two-Stage Complex Upconversion
IMAGE REJECTION AND SIDEBAND
SUPPRESSIONS OF MODULATED CARRIERS
It is important to remember that the magnitude of a complex
signal can be 1.414× the magnitude of its real or imaginary
components. Due to this 3 dB increase in signal amplitude, the
real and imaginary inputs to the AD9777 must be kept at least
3 dB below full scale when operating with the complex
modulator. Overranging in the complex modulator results in
severe distortion at the DAC output.
As shown in Figure 79, image rejection can be achieved by
applying baseband data to the AD9777 and following the
AD9777 with a quadrature modulator. To process multiple
carriers while still maintaining image reject capability, each
carrier must be complex modulated. As Figure 80 shows, single
or multiple complex modulators can be used to synthesize
complex carriers. These complex carriers are then summed and
applied to the real and imaginary inputs of the AD9777.
BASEBAND CHANNEL 1
R(1)
REAL INPUT
COMPLEX
MULTICARRIER
REAL OUTPUT =
R(1) + R(2) + . . .R(N)
(TO REAL INPUT OF AD9777)
MODULATOR 1
R(1)
IMAGINARY INPUT
BASEBAND CHANNEL 2
REAL INPUT
R(2)
R(2)
COMPLEX
MODULATOR 2
MULTICARRIER
IMAGINARY OUTPUT =
I(1) + I(2) + . . .I(N)
IMAGINARY INPUT
(TO IMAGINARY INPUT OF AD9777)
R(N) = REAL OUTPUT OF N
I(N) = IMAGINARY OUTPUT OF N
BASEBAND CHANNEL N
REAL INPUT
R(N)
R(N)
COMPLEX
MODULATOR N
IMAGINARY INPUT
Figure 81. Synthesis of Multicarrier Complex Signal
MULTIPLE
BASEBAND
CHANNELS
REAL
REAL
REAL
REAL
MULTIPLE
COMPLEX
MODULATORS
AD9777
COMPLEX
MODULATOR
FREQUENCY = ω
QUADRATURE
MODULATOR
FREQUENCY = ω
IMAGINARY
IMAGINARY
IMAGINARY
Q
FREQUENCY = ω , ω ...ω
1
2
N
C
COMPLEX BASEBAND
SIGNAL
×
OUTPUT = REAL
j(ω + ω + ω )t
e
N
C
Q
–ω – ω – ω
ω
+ ω + ω
Q
DC
REJECTED IMAGES
1
C
Q
1
C
Figure 82. Image Rejection with Multicarrier Signals
Rev. C | Page 41 of 60
AD9777
The complex carrier synthesized in the AD9777 digital
Region C
modulator is accomplished by creating two real digital carriers
in quadrature. Carriers in quadrature cannot be created with
the modulator running at fDAC/2. As a result, complex modula-
tion only functions with modulation rates of fDAC/4 and fDAC/8.
Region C is most accurately described as a down conversion, as
the modulating carrier is −ejωt. If viewed as a complex signal,
only the images in Region C remains. This image appears on
the real and imaginary outputs of the AD9777, as well as on the
output of the quadrature modulator, where the center of the
spectral plot now represents the quadrature modulator LO and
the horizontal scale represents the frequency offset from this
LO.
Region A and Region B of Figure 83 to Figure 88 are the result
of the complex signal described previously, when complex
modulated in the AD9777 by +ejωt. Region C and Region D are
the result of the complex signal described previously, again with
positive frequency components only, modulated in the AD9777
by −ejωt. The analog quadrature modulator after the AD9777
inherently modulates by +ejωt.
Region D
Region D is the image (complex conjugate) of Region C. If a
spectrum analyzer is used to view the real or imaginary DAC
outputs of the AD9777, Region D appears in the spectrum.
However, on the output of the quadrature modulator, Region D
is rejected.
Region A
Region A is a direct result of the upconversion of the complex
signal near baseband. If viewed as a complex signal, only the
images in Region A remains. The complex Signal A, consisting
of positive frequency components only in the digital domain,
has images in the positive odd Nyquist zones (1, 3, 5, and so
on), as well as images in the negative even Nyquist zones. The
appearance and rejection of images in every other Nyquist zone
becomes more apparent at the output of the quadrature
modulator. The A images appear on the real and the imaginary
outputs of the AD9777, as well as on the output of the
Figure 89 to Figure 96 show the measured response of the
AD9777 and AD8345 given the complex input signal to the
AD9777 in Figure 89. The data in these graphs was taken with a
data rate of 12.5 MSPS at the AD9777 inputs. The interpolation
rate of 4× or 8× gives a DAC output data rate of 50 MSPS or
100 MSPS. As a result, the high end of the DAC output
spectrum in these graphs is the first null point for the SIN(x)/x
roll-off, and the asymmetry of the DAC output images is
representative of the SIN(x)/x roll-off over the spectrum. The
internal PLL was enabled for these results. In addition, a
35 MHz third-order low-pass filter was used at the AD9777/
AD8345 interface to suppress DAC images.
quadrature modulator, where the center of the spectral plot now
represents the quadrature modulator LO and the horizontal scale
now represents the frequency offset from this LO.
Region B
Region B is the image (complex conjugate) of Region A. If a
spectrum analyzer is used to view the real or imaginary DAC
outputs of the AD9777, Region B appears in the spectrum.
However, on the output of the quadrature modulator, Region B
is rejected.
An important point can be made by looking at Figure 91 and
Figure 93. Figure 91 represents a group of positive frequencies
modulated by complex +fDAC/4, while Figure 93 represents a
group of negative frequencies modulated by complex −fDAC/4.
When looking at the real or imaginary outputs of the AD9777,
as shown in Figure 91 and Figure 93, the results look identical.
However, the spectrum analyzer cannot show the phase
relationship of these signals. The difference in phase between
the two signals becomes apparent when they are applied to the
AD8345 quadrature modulator, with the results shown in Figure
92 and Figure 94.
Rev. C | Page 42 of 60
AD9777
0
–20
–40
–60
–80
0
–20
–40
–60
–80
D
A
B
C
D
A
B
C
D
A
B
C D
A
B
C
–100
–100
–2.0
–1.5
–1.0
–0.5
0
0.5
1.0
1.5
2.0
–2.0
–1.5
–1.0
–0.5
0
0.5
1.0
1.5
2.0
(LO)
(LO)
fOUT (×fDATA
fOUT (×fDATA
)
)
Figure 83. 2× Interpolation, Complex fDAC/4 Modulation
Figure 86. 2× Interpolation, Complex fDAC/8 Modulation
0
–20
–40
–60
–80
0
–20
–40
–60
–80
D
A
B
C
D
A
B
C
D
A
B
C
D
A
B
C
–100
–100
–4.0
–3.0
–2.0
–1.0
0
1.0
2.0
3.0
4.0
–4.0
–3.0
–2.0
–1.0
0
1.0
2.0
3.0
4.0
(LO)
(LO)
fOUT (×fDATA
fOUT (×fDATA
)
)
Figure 84. 4× Interpolation, Complex fDAC/4 Modulation
Figure 87. 4× Interpolation, Complex fDAC/8 Modulation
0
–20
–40
–60
–80
0
–20
–40
–60
–80
D
A
B
C
D
A
B
C
D A
B C
D A
B C
–100
–100
–8.0
–6.0
–4.0
–2.0
0
2.0
4.0
6.0
8.0
–8.0
–6.0
–4.0
–2.0
0
2.0
4.0
6.0
8.0
(LO)
(LO)
fOUT (×fDATA
)
fOUT (×fDATA
)
Figure 85. 8× Interpolation, Complex fDAC/4 Modulation
Figure 88. 8× Interpolation, Complex fDAC/8 Modulation
Rev. C | Page 43 of 60
AD9777
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–100
0
10
20
30
40
50
750 760 770 780 790 800 810 820 830 840 850
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 89. AD9777, Real DAC Output of Complex Input Signal Near Baseband
(Positive Frequencies Only), Interpolation = 4×, No Modulation in AD9777
Figure 92. AD9777 Complex Output from Figure 91, Now Quadrature
Modulated by AD8345 (LO = 800 MHz)
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
0
10
20
30
40
50
–100
750 760 770 780 790 800 810 820 830 840 850
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 93. AD9777, Real DAC Output of Complex Input Signal Near
Baseband (Negative Frequencies Only), Interpolation = 4×,
Complex Modulation in AD9777 = −fDAC/4
Figure 90. AD9777 Complex Output from Figure 89, Now Quadrature
Modulated by AD8345 (LO = 800 MHz)
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–100
750 760 770 780 790 800 810 820 830 840 850
0
10
20
30
40
50
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 91. AD9777, Real DAC Output of Complex Input Signal Near
Baseband (Positive Frequencies Only), Interpolation = 4×,
Complex Modulation in AD9777 = +fDAC/4
Figure 94. AD9777 Complex Output from Figure 93, Now Quadrature
Modulated by AD8345 (LO = 800 MHz)
Rev. C | Page 44 of 60
AD9777
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
0
–20
–40
–60
–80
–100
700 720 740 760 780 800 820 840 860 880 900
0
20
40
60
80
100
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 95. AD9777, Real DAC Output of Complex Input Signal Near
Baseband (Positive Frequencies Only), Interpolation = 8×,
Complex Modulation in AD9777 = +fDAC/8
Figure 96. AD9777 Complex Output from Figure 95, Now Quadrature
Modulated by AD8345 (LO = 800 MHz)
Rev. C | Page 45 of 60
AD9777
APPLYING THE OUTPUT CONFIGURATIONS
The following sections illustrate typical output configurations
for the AD9777. Unless otherwise noted, it is assumed that
IOUTFS is set to a nominal 20 mA. For applications requiring
optimum dynamic performance, a differential output configu-
ration is suggested. A simple differential output may be
achieved by converting IOUTA and IOUTB to a voltage output by
terminating them to AGND via equal value resistors. This type
of configuration may be useful when driving a differential
voltage input device such as a modulator. If a conversion to a
single-ended signal is desired and the application allows for ac
coupling, an RF transformer may be useful; if power gain is
required, an op amp may be used. The transformer configura-
tion provides optimum high frequency noise and distortion
performance. The differential op amp configuration is suitable
for applications requiring dc coupling, signal gain, and/or level
shifting within the bandwidth of the chosen op amp.
For the typical situation, where IOUTFS = 20 mA and RA and RB
both equal 50 Ω, the equivalent circuit values become
VSOURCE = 2 VP-P
ROUT = 100 Ω
Note that the output impedance of the AD9777 DAC itself is
greater than 100 kΩ and typically has no effect on the
impedance of the equivalent output circuit.
DIFFERENTIAL COUPLING USING A
TRANSFORMER
An RF transformer can be used to perform a differential-to-
single-ended signal conversion, as shown in Figure 98. A
differentially coupled transformer output provides the optimum
distortion performance for output signals whose spectral
content lies within the transformer’s pass band. An RF
transformer, such as the Mini-Circuits T1-1T, provides excellent
rejection of common-mode distortion (that is, even-order
harmonics) and noise over a wide frequency range. It also
provides electrical isolation and the ability to deliver twice the
power to the load. Transformers with different impedance ratios
may also be used for impedance matching purposes.
A single-ended output is suitable for applications requiring a
unipolar voltage output. A positive unipolar output voltage
results if IOUTA and/or IOUTB is connected to a load resistor, RLOAD
referred to AGND. This configuration is most suitable for a
single-supply system requiring a dc-coupled, ground referred
output voltage. Alternatively, an amplifier could be configured
as an I-V converter, thus converting IOUTA or IOUTB into a
negative unipolar voltage. This configuration provides the best
DAC dc linearity as IOUTA or IOUTB are maintained at ground or
virtual ground.
,
MINI-CIRCUITS
T1-1T
I
OUTA
DAC
R
LOAD
I
OUTB
Figure 98. Transformer-Coupled Output Circuit
UNBUFFERED DIFFERENTIAL OUTPUT,
EQUIVALENT CIRCUIT
The center tap on the primary side of the transformer must be
connected to AGND to provide the necessary dc current path
for both IOUTA and IOUTB. The complementary voltages appearing
at IOUTA and IOUTB (that is, VOUTA and VOUTB) swing symmetrically
around AGND and should be maintained within the specified
output compliance range of the AD9777. A differential resistor,
RDIFF, can be inserted in applications where the output of the
transformer is connected to the load, RLOAD, via a passive
reconstruction filter or cable. RDIFF is determined by the
transformer’s impedance ratio and provides the proper source
termination that results in a low VSWR. Note that approxi-
In many applications, it may be necessary to understand the
equivalent DAC output circuit. This is especially useful when
designing output filters or when driving inputs with finite input
impedances. Figure 97 illustrates the output of the AD9777 and
the equivalent circuit. A typical application where this
information may be useful is when designing an interface filter
between the AD9777 and the Analog Devices AD8345
quadrature modulator.
V
+
–
I
I
OUT
OUT
OUTA
OUTB
mately half the signal power dissipates across RDIFF
.
V
R
+ R
B
A
V
=
)
p-p
SOURCE
× (R + R
V
OUT
(DIFFERENTIAL)
I
OUTFS
A
B
Figure 97. DAC Output Equivalent Circuit
Rev. C | Page 46 of 60
AD9777
Gain/Offset Adjust
DIFFERENTIAL COUPLING USING AN OP AMP
The matching of the DAC output to the common-mode input
of the AD8345 allows the two components to be dc-coupled,
with no level shifting necessary. The combined voltage offset of
the two parts can therefore be compensated via the AD9777
programmable offset adjust. This allows excellent LO
cancellation at the AD8345 output. The programmable gain
adjust allows for optimal image rejection as well.
An op amp can also be used to perform a differential-to-single
ended conversion, as shown in Figure 99. This has the added
benefit of providing signal gain as well. In Figure 99, the
AD9777 is configured with two equal load resistors, RLOAD, of
25 Ω. The differential voltage developed across IOUTA and IOUTB is
converted to a single-ended signal via the differential op amp
configuration. An optional capacitor can be installed across
IOUTA and IOUTB, forming a real pole in a low-pass filter. The
addition of this capacitor also enhances the op amp’s distortion
performance by preventing the DAC’s fast slewing output from
overloading the input of the op amp.
The AD9777 evaluation board includes an AD8345 and
recommended interface (Figure 105 and Figure 106). On the
output of the AD9777, R9 and R10 convert the DAC output
current to a voltage. R16 can be used to do a slight common-
mode shift if necessary. The (now voltage) signal is applied to a
low-pass reconstruction filter to reject DAC images. The
components installed on the AD9777 provide a 35 MHz cutoff
but can be changed to fit the application. A balun (Mini-
Circuits ADTL1-12) is used to cross the ground plane boundary
to the AD8345. Another balun (Mini-Circuits ETC1-1-13) is
used to couple the LO input of the AD8345. The interface
requires a low ac impedance return path from the AD8345,
therefore a single connection between the AD9777 and AD8345
ground planes is recommended.
500Ω
225Ω
I
OUTA
AD8021
DAC
I
OUTB
C
OPT
225Ω
500Ω
AVDD
R
OPT
225Ω
25Ω
25Ω
Figure 99. Op Amp-Coupled Output Circuit
The common-mode (and second-order distortion) rejection of
this configuration is typically determined by the resistor
matching. The op amp used must operate from a dual supply
since its output is approximately 1.0 V. A high speed amplifier,
such as the AD8021, capable of preserving the differential
performance of the AD9777 while meeting other system level
objectives (for example, cost, power) is recommended. The op
amp’s differential gain, gain setting resistor values, and full-scale
output swing capabilities should all be considered when
optimizing this circuit. ROPT is necessary only if level shifting is
required on the op amp output. In Figure 99, AVDD, which is
the positive analog supply for both the AD9777 and the op amp,
is also used to level shift the differential output of the AD9777
to midsupply (that is, AVDD/2).
The performance of the AD9777 and AD8345 in an image
reject transmitter, reconstructing three WCDMA carriers, can
be seen in Figure 100. The LO of the AD8345 in this application
is 800 MHz. Image rejection (50 dB) and LO feedthrough
(−78 dBFS) have been optimized with the programmable
features of the AD9777. The average output power of the digital
waveform for this test was set to −15 dBFS to account for the
peak-to-average ratio of the WCDMA signal.
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
INTERFACING WITH THE AD8345 QUADRATURE
MODULATOR
The AD9777 architecture was defined to operate in a transmit
signal chain using an image reject architecture. A quadrature
modulator is also required in this application and should be
designed to meet the output characteristics of the DAC as much
as possible. The AD8345 from Analog Devices meets many of
the requirements for interfacing with the AD9777. As with any
DAC output interface, there are a number of issues that have to
be resolved. The following sections list some of the major issues.
762.5
782.5
802.5
822.5
842.5
FREQUENCY (MHz)
Figure 100. AD9777/AD8345 Synthesizing a
Three-Carrier WCDMA Signal at an LO of 800 MHz
DAC Compliance Voltage/Input Common-Mode Range
The dynamic range of the AD9777 is optimal when the DAC
outputs swing between 1.0 V. The input common-mode range
of the AD8345, at 0.7 V, allows optimum dynamic range to be
achieved in both components.
Rev. C | Page 47 of 60
AD9777
EVALUATION BOARD
DAC Differential Outputs
The AD9777 evaluation board allows easy configuration of the
various modes, programmable via the SPI port. Software is
available for programming the SPI port from Windows® 95,
Windows 98, or Windows NT®/2000. The evaluation board also
contains an AD8345 quadrature modulator and support
circuitry that allows the user to optimally configure the AD9777
in an image reject transmit signal chain.
Transformers T2 and T3 should be in place. Note that the lower
band of operation for these transformers is 300 kHz to 500 kHz.
Jumpers 4, 8, 13 to 17, and 28 to 30 should remain unsoldered.
The outputs are taken from S3 and S4.
Using the AD8345
Remove Transformers T2 and T3. Jumpers JP4 and 28 to 30
should remain unsoldered. Jumpers 13 to 16 should be
soldered. The desired components for the low-pass interface
filters L6, L7, C55, and C81 should be in place. The LO drive is
connected to the AD8345 via J10 and the balun T4, and the
AD8345 output is taken from J9.
Figure 101 to Figure 104 describe how to configure the
evaluation board in the one-port and two-port input modes with
the PLL enabled and disabled. Refer to Figure 105 to Figure 114,
the schematics, and the layout for the AD9777 evaluation board
for the jumper locations described below. The AD9777 outputs
can be configured for various applications by referring to the
following instructions.
DAC Single-Ended Outputs
Remove Transformers T2 and T3. Solder jumper link JP4 or
JP28 to look at the DAC1 outputs. Solder jumper link JP29 or
JP30 to look at the DAC2 outputs. Jumpers 8 and 13 to 17
should remain unsoldered. Jumpers JP35 to JP38 may be used
to ground one of the DAC outputs while the other is measured
single-ended. Optimum single-ended distortion performance is
typically achieved in this manner. The outputs are taken from
S3 and S4.
Rev. C | Page 48 of 60
AD9777
LECROY
PULSE
GENERATOR
SIGNAL GENERATOR
TRIG
INP
DATACLK
CLK+/CLK–
INPUT CLOCK
AWG2021
OR
DG2020
40-PIN RIBBON CABLE
DAC1, DB15–DB0
DAC2, DB15–DB0
AD9777
JUMPER CONFIGURATION FOR TWO PORT MODE PLL ON
SOLDERED/IN UNSOLDERED/OUT
JP1 –
JP2 –
×
×
JP3 –
JP5 –
×
×
JP6 –
×
×
×
JP12 –
JP24 –
JP25 –
JP26 –
JP27 –
JP31 –
JP32 –
JP33 –
×
×
×
×
×
×
NOTES
1. TO USE PECL CLOCK DRIVER (U8), SOLDER JP41 AND JP42 AND REMOVE TRANSFORMER T1.
2. IN TWO-PORT MODE, IF DATACLK/PLL_LOCK IS PROGRAMMED TO OUTPUT PIN 8, JP25 AND
JP39 SHOULD BE SOLDERED. IF DATACLK/PLL_LOCK IS PROGRAMMED TO OUTPUT PIN 53,
JP46 AND JP47 SHOULD BE SOLDERED. SEE THE TWO PORT DATA INPUT MODE SECTION
FOR MORE INFORMATION.
Figure 101. Test Configuration for AD9777 in Two-Port Mode with PLL Enabled Signal Generator Frequency = Input Data Rate,
DAC Output Data Rate = Signal Generator Frequency × Interpolation Rate
LECROY
PULSE
GENERATOR
SIGNAL GENERATOR
TRIG
INP
ONEPORTCLK
CLK+/CLK–
INPUT CLOCK
AWG2021
OR
DG2020
DAC1, DB15–DB0
DAC2, DB15–DB0
AD9777
JUMPER CONFIGURATION FOR ONE PORT MODE PLL ON
SOLDERED/IN UNSOLDERED/OUT
JP1 –
JP2 –
×
×
JP3 –
×
JP5 –
JP6 –
×
×
×
×
JP12 –
JP24 –
JP25 –
JP26 –
JP27 –
JP31 –
JP32 –
JP33 –
×
×
×
×
×
×
NOTES
1. TO USE PECL CLOCK DRIVER (U8), SOLDER JP41 AND JP42 AND REMOVE TRANSFORMER T1.
Figure 102. Test Configuration for AD9777 in One-Port Mode with PLL Enabled, Signal Generator Frequency = One-Half Interleaved Input Data Rate,
ONEPORTCLK = Interleaved Input Data Rate, DAC Output Data Rate = Signal Generator Frequency × Interpolation Rate
Rev. C | Page 49 of 60
AD9777
LECROY
PULSE
GENERATOR
SIGNAL GENERATOR
TRIG
INP
DATACLK
CLK+/CLK–
INPUT CLOCK
AWG2021
OR
DG2020
40-PIN RIBBON CABLE
DAC1, DB15–DB0
DAC2, DB15–DB0
AD9777
JUMPER CONFIGURATION FOR TWO PORT MODE PLL OFF
SOLDERED/IN UNSOLDERED/OUT
JP1 –
JP2 –
×
×
JP3 –
JP5 –
×
×
JP6 –
×
×
×
JP12 –
JP24 –
JP25 –
JP26 –
JP27 –
JP31 –
JP32 –
JP33 –
×
×
×
×
×
×
NOTES
1. TO USE PECL CLOCK DRIVER (U8), SOLDER JP41 AND JP42 AND REMOVE TRANSFORMER T1.
2. IN TWO-PORT MODE, IF DATACLK/PLL_LOCK IS PROGRAMMED TO OUTPUT PIN 8, JP25 AND
JP39 SHOULD BE SOLDERED. IF DATACLK/PLL_LOCK IS PROGRAMMED TO OUTPUT PIN 53,
JP46 AND JP47 SHOULD BE SOLDERED. SEE THE TWO PORT DATA INPUT MODE SECTION
FOR MORE INFORMATION.
Figure 103. Test Configuration for AD9777 in Two-Port Mode with PLL Disabled, DAC Output Data Rate = Signal Generator Frequency,
DATACLK = Signal Generator Frequency/Interpolation Rate
LECROY
PULSE
GENERATOR
SIGNAL GENERATOR
TRIG
INP
ONEPORTCLK
CLK+/CLK–
INPUT CLOCK
AWG2021
OR
DG2020
DAC1, DB15–DB0
DAC2, DB15–DB0
AD9777
JUMPER CONFIGURATION FOR ONE PORT MODE PLL OFF
SOLDERED/IN UNSOLDERED/OUT
JP1 –
JP2 –
×
×
JP3 –
×
JP5 –
JP6 –
×
×
×
×
JP12 –
JP24 –
JP25 –
JP26 –
JP27 –
JP31 –
JP32 –
JP33 –
×
×
×
×
×
×
NOTES
1. TO USE PECL CLOCK DRIVER (U8), SOLDER JP41 AND JP42 AND REMOVE TRANSFORMER T1.
Figure 104. Test Configuration for AD9777 in One-Port Mode with PLL Disabled, DAC Output Data Rate = Signal Generator Frequency,
ONEPORTCLK = Interleaved Input Data Rate = 2× Signal Generator Frequency/Interpolation Rate.
Rev. C | Page 50 of 60
AD9777
0 6 C 0 R 3
0 6 C 0 R 3
G 2
G 3
N E B L
V P S 1
T
V O U
L O I P
L O I N
G 1 B
G 1 A
V P S 2
G 4 A
G 4 B
Q B B N I B B N
Q B B P I B B P
A D T L 1 - 1 2
A D T L 1 - 1 2
0 6 C 0 C 3
0 8 C 0 C 5
Figure 105. AD8345 Circuitry on AD9777 Evaluation Board
Rev. C | Page 51 of 60
AD9777
C C 0 6 0 3
R C 1 2 0 6
C C 0 6 0 3
R C 0 6 0 3
R C 0 6 0 3
C C 0 6 0 5
C C 0 6 0 3
C C 0 8 0 5
Figure 106. AD9777 Clock, Power Supplies, and Output Circuitry
Rev. C | Page 52 of 60
AD9777
Figure 107. AD9777 Evaluation Board Input (A Channel) and Clock Buffer Circuitry
Rev. C | Page 53 of 60
AD9777
Figure 108. AD9777 Evaluation Board Input (B Channel) and SPI Port Circuitry
Rev. C | Page 54 of 60
AD9777
Figure 109. AD9777 Evaluation Board Components, Top Side
Figure 110. AD9777 Evaluation Board Components, Bottom Side
Rev. C | Page 55 of 60
AD9777
Figure 111. AD9777 Evaluation Board Layout, Layer One (Top)
Figure 112. AD9777 Evaluation Board Layout, Layer Two (Ground Plane)
Rev. C | Page 56 of 60
AD9777
Figure 113. AD9777 Evaluation Board Layout, Layer Three (Power Plane)
Figure 114. AD9777 Evaluation Board Layout, Layer Four (Bottom)
Rev. C | Page 57 of 60
AD9777
OUTLINE DIMENSIONS
14.20
14.00 SQ
13.80
12.20
1.20
MAX
12.00 SQ
11.80
0.75
0.60
0.45
61
80
80
61
1
60
1
60
PIN 1
EXPOSED
PAD
6.00
BSC SQ
TOP VIEW
(PINS DOWN)
BOTTOM VIEW
(PINS UP)
0° MIN
1.05
1.00
0.95
0.20
0.09
7°
3.5°
0°
20
41
41
20
40
40
21
21
VIEW A
0.15
0.05
0.50 BSC
0.27
0.22
0.17
SEATING
PLANE
LEAD PITCH
0.08 MAX
COPLANARITY
VIEW A
ROTATED 90° CCW
COMPLIANT TO JEDEC STANDARDS MS-026-ADD-HD
Figure 115. 80-Lead Thin Quad Flat Package, Exposed Pad [TQFP_EP]
(SV-80-1)
Dimensions shown in millimeters
ORDERING GUIDE
Model
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
Package Option
AD9777BSV
AD9777BSVRL
AD9777BSVZ1
80-Lead Thin Quad Flat Package, Exposed Pad [TQFP_EP]
80-Lead Thin Quad Flat Package, Exposed Pad [TQFP_EP]
80-Lead Thin Quad Flat Package, Exposed Pad [TQFP_EP]
80-Lead Thin Quad Flat Package, Exposed Pad [TQFP_EP]
Evaluation Board
SV-80-1
SV-80-1
SV-80-1
SV-80-1
AD9777BSZVRL1 −40°C to +85°C
AD9777-EB
1 Z = Pb-free part.
Rev. C | Page 58 of 60
AD9777
NOTES
Rev. C | Page 59 of 60
AD9777
NOTES
©
2005 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C02706-0-1/06(C)
Rev. C | Page 60 of 60
相关型号:
AD9777AST
IC SERIAL INPUT LOADING, 16-BIT DAC, PQFP80, 1.40 MM HEIGHT, PLASTIC, LQFP-80, Digital to Analog Converter
ADI
©2020 ICPDF网 联系我们和版权申明