ADF4116BRUZ-REEL7 [ADI]
Single, Integer-N 550 MHz PLL;型号: | ADF4116BRUZ-REEL7 |
厂家: | ADI |
描述: | Single, Integer-N 550 MHz PLL 信息通信管理 光电二极管 |
文件: | 总28页 (文件大小:400K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
RF PLL Frequency Synthesizers
ADF4116/ADF4117/ADF4118
GENERAL DESCRIPTION
FEATURES
ADF4116: 550 MHz
ADF4117: 1.2 GHz
ADF4118: 3.0 GHz
The ADF411x family of frequency synthesizers can be used to
implement local oscillators (LO) in the upconversion and
downconversion sections of wireless receivers and transmitters.
They consist of a low noise digital phase frequency detector
(PFD), a precision charge pump, a programmable reference
divider, programmable A and B counters, and a dual-modulus
prescaler (P/P + 1). The A (5-bit) and B (13-bit) counters, in
conjunction with the dual-modulus prescaler (P/P + 1),
implement an N divider (N = BP + A). In addition, the 14-bit
reference counter (R counter) allows selectable REFIN frequencies
at the PFD input. A complete phase-locked loop (PLL) can be
implemented if the synthesizer is used with an external loop
filter and voltage controlled oscillator (VCO).
2.7 V to 5.5 V power supply
Separate VP allows extended tuning voltage in 3 V systems
Y Grade: −40°C to +125°C
Dual-modulus prescaler
ADF4116: 8/9
ADF4117/ADF4118: 32/33
3-wire serial interface
Digital lock detect
Power-down mode
Fastlock mode
APPLICATIONS
All of the on-chip registers are controlled via a simple 3-wire
interface. The devices operate with a power supply ranging
from 2.7 V to 5.5 V and can be powered down when not in use.
Base stations for wireless radio
(GSM, PCS, DCS, CDMA, WCDMA)
Wireless handsets
(GSM, PCS, DCS, CDMA, WCDMA)
Wireless LANs
Communications test equipment
CATV equipment
FUNCTIONAL BLOCK DIAGRAM
AV
DV
V
P
CPGND
DD
DD
REFERENCE
ADF4116/ADF4117/ADF4118
14-BIT
R COUNTER
REF
IN
PHASE
FREQUENCY
DETECTOR
CHARGE
PUMP
CP
14
R COUNTER
LATCH
CLK
DATA
LE
21-BIT
INPUT REGISTER
FUNCTION
LATCH
LOCK
DETECT
19
A, B COUNTER
LATCH
SD
OUT
18
HIGH Z
FROM
FUNCTION LATCH
AV
DD
13
MUX
MUXOUT
N = BP + A
13-BIT
B COUNTER
SD
OUT
RF
RF
A
B
IN
LOAD
LOAD
PRESCALER
P/P + 1
IN
5-BIT
A COUNTER
M3 M2 M1
FL
SWITCH
O
FL
O
5
CE
AGND
DGND
Figure 1.
Rev. D
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 www.analog.com
Fax: 781.461.3113 ©2000–2007 Analog Devices, Inc. All rights reserved.
ADF4116/ADF4117/ADF4118
TABLE OF CONTENTS
Features .............................................................................................. 1
Latch Summaries........................................................................ 14
Latch Maps .................................................................................. 15
Function Latch................................................................................ 19
Counter Reset ............................................................................. 19
Power-Down ............................................................................... 19
MUXOUT Control..................................................................... 19
Phase Detector Polarity ............................................................. 19
Charge Pump Three-State......................................................... 19
Fastlock Enable Bit..................................................................... 19
Fastlock Mode Bit....................................................................... 19
Timer Counter Control ............................................................. 19
Initialization Latch ..................................................................... 20
Device Programming After Initial Power-Up ........................ 20
Applications Information.............................................................. 21
Local Oscillator for the GSM Base Station Transmitter........ 21
Shutdown Circuit ....................................................................... 21
Direct Conversion Modulator .................................................. 21
Interfacing ................................................................................... 24
Outline Dimensions....................................................................... 25
Ordering Guide .......................................................................... 25
Applications....................................................................................... 1
General Description......................................................................... 1
Functional Block Diagram .............................................................. 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Timing Characteristics ................................................................ 5
Absolute Maximum Ratings............................................................ 6
ESD Caution.................................................................................. 6
Pin Configuration and Function Descriptions............................. 7
Typical Performance Characteristics ............................................. 8
Circuit Description......................................................................... 12
Reference Input Section............................................................. 12
RF Input Stage............................................................................. 12
Prescaler (P/P + 1)...................................................................... 12
A Counter and B Counter ......................................................... 12
R Counter .................................................................................... 12
Phase Frequency Detector (PFD) and Charge Pump............ 13
MUXOUT and Lock Detect...................................................... 13
Input Shift Register..................................................................... 13
REVISION HISTORY
9/04—Rev. A to Rev. B
4/07—Rev. C to Rev. D
Changes to Specifications.................................................................3
Changes to Ordering Guide.......................................................... 25
Changes to REFIN Characteristics Section..................................... 3
Changes to Table 4............................................................................ 7
Changes to Figure 35...................................................................... 22
Changes to Ordering Guide .......................................................... 25
3/01—Rev. 0 to Rev. A
4/00—Rev. 0: Initial Version
11/05—Rev. B to Rev. C
Changes to Table 1............................................................................ 3
Changes to Table 2............................................................................ 5
Changes to Table 3............................................................................ 6
Changes to Table 4............................................................................ 7
Changed OSC 3B1-13M0 to FOX801BH-130............................ 21
Changes to Ordering Guide .......................................................... 25
Rev. D | Page 2 of 28
ADF4116/ADF4117/ADF4118
SPECIFICATIONS
AVDD = DVDD = 3 V 10ꢀ, 5 V 10ꢀꢁ AVDD ≤ VP ≤ 6.0 Vꢁ AGND = DGND = CPGND = 0 Vꢁ TA = TMIN to TMAX, unless otherwise
notedꢁ dBm referred to 50 Ω.
Table 1.
Parameter
B Version1
Y Version2 Unit
Test Conditions/Comments
RF CHARACTERISTICS
RF Input Sensitivity
−15 to 0
−10 to 0
−10 to 0
−10 to 0
dBm min to max
dBm min to max
AVDD = 3 V
AVDD = 5 V
RF Input Frequency
ADF4116
See Figure 26 for input circuit
80 to 550
45 to 550
MHz min to max
MHz min to max
Input level = −8 dBm; for lower frequencies,
ensure slew rate (SR) > 36 V/μs
ADF4117
ADF4118
0.1 to 1.2
0.1 to 3.0
0.2 to 3.0
165
GHz min to max
GHz min to max
GHz min to max
MHz max
0.1 to 3.0
Input level = −10 dBm
Input level = −15 dBm
AVDD, DVDD = 3 V
Maximum Allowable Prescaler
Output Frequency3
165
200
200
MHz max
AVDD, DVDD = 5 V
REFIN CHARACTERISTICS
Reference Input Frequency
Reference Input Sensitivity4,5
5 to 100
0.4 to AVDD
0.7 to AVDD
10
5 to 100
MHz min to max
For f < 5 MHz, ensure SR > 100 V/μs
0.4 to AVDD V p-p min to max AVDD = 3.3 V, biased at AVDD/2
0.7 to AVDD V p-p min to max For f ≥ 10 MHz, AVDD = 5 V, biased at AVDD/2
10
100
REFIN Input Capacitance
REFIN Input Current
PHASE DETECTOR FREQUENCY5
CHARGE PUMP
pF max
μA max
MHz max
100
55
55
ICP Sink/Source
High Value
Low Value
Absolute Accuracy
ICP Three-State Leakage Current
1
1
mA typ
μA typ
% typ
nA max
nA typ
% typ
250
2.5
3
1
3
250
2.5
25
16
3
Sink and Source Current Matching
ICP vs. VCP
0.5 V ≤ VCP ≤ VP − 0.5
0.5 V ≤ VCP ≤ VP − 0.5
VCP = VP/2
2
2
% typ
ICP vs. Temperature
2
2
% typ
LOGIC INPUTS
VINH, Input High Voltage
VINL, Input Low Voltage
IINH/IINL, Input Current
CIN, Input Capacitance
Reference Input Current
LOGIC OUTPUTS
0.8 × DVDD
0.2 × DVDD
1
10
0.8 × DVDD
0.2 × DVDD
1
10
100
V min
V max
μA max
pF max
μA max
100
VOH, Output High Voltage
VOL, Output Low Voltage
DVDD − 0.4
0.4
DVDD − 0.4
0.4
V min
V max
IOH = 500 μA
IOL = 500 μA
Rev. D | Page 3 of 28
ADF4116/ADF4117/ADF4118
Parameter
B Version1
Y Version2 Unit
Test Conditions/Comments
POWER SUPPLIES
AVDD
DVDD
2.7 to 5.5
AVDD
2.7 to 5.5
AVDD
V min to V max
VP
AVDD to 6.0
AVDD to 6.0 V min to V max
AVDD ≤ VP ≤ 6.0 V
IDD (AIDD + DIDD)6
ADF4116
ADF4117
ADF4118
5.5
5.5
7.5
0.4
1
mA max
mA max
mA max
mA max
μA typ
4.5 mA typical
4.5 mA typical
6.5 mA typical
TA = 25°C
7.5
0.4
1
IP
Low-Power Sleep Mode
NOISE CHARACTERISTICS
ADF4118 Normalized Phase Noise
−213
−213
dBc/Hz typ
Floor7
Phase Noise Performance8
ADF4116 540 MHz Output9
ADF4117 900 MHz Output10
ADF4118 900 MHz Output10
ADF4117 836 MHz Output11
ADF4118 1750 MHz Output12
ADF4118 1750 MHz Output13
ADF4118 1960 MHz Output14
Spurious Signals
@ VCO output
−89
−87
−90
−78
−85
−65
−84
−89
−87
−90
−78
−85
−65
−84
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
@ 1 kHz offset and 200 kHz PFD frequency
@ 1 kHz offset and 200 kHz PFD frequency
@ 1 kHz offset and 200 kHz PFD frequency
@ 300 Hz offset and 30 kHz PFD frequency
@ 1 kHz offset and 200 kHz PFD frequency
@ 200 Hz offset and 10 kHz PFD frequency
@ 1 kHz offset and 200 kHz PFD frequency
ADF4116 540 MHz Output10
ADF4117 900 MHz Output10
ADF4118 900 MHz Output10
ADF4117 836 MHz Output11
ADF4118 1750 MHz Output12
ADF4118 1750 MHz Output13
ADF4118 1960 MHz Output14
−88/−99
−90/−104
−91/−100
−80/−84
−88/−90
−65/−73
−80/−86
−88/−99
−90/−104
−91/−100
−80/−84
−88/−90
−65/−73
−80/−86
dBc typ
dBc typ
dBc typ
dBc typ
dBc typ
dBc typ
dBc typ
@ 200 kHz/400 kHz and 200 kHz PFD frequency
@ 200 kHz/400 kHz and 200 kHz PFD frequency
@ 200 kHz/400 kHz and 200 kHz PFD frequency
@ 30 kHz/60 kHz and 30 kHz PFD frequency
@ 200 kHz/400 kHz and 200 kHz PFD frequency
@ 10 kHz/20 kHz and 10 kHz PFD frequency
@ 200 kHz/400 kHz and 200 kHz PFD frequency
1 Operating temperature range for the B version is −40°C to +85°C.
2 Operating temperature range for the Y version is −40°C to +125°C.
3 This is the maximum operating frequency of the CMOS counters.
4 AC coupling ensures AVDD/2 bias. See Figure 35 for typical circuit.
5 Guaranteed by design.
6 TA = 25°C; AVDD = DVDD = 3 V; RFIN for ADF4116 = 540 MHz; RFIN for ADF4117, ADF4118 = 900 MHz.
7 The synthesizer phase noise floor is estimated by measuring the in-band phase noise at the output of the VCO, PNTOT, and subtracting 20logN (where N is the N
divider value) and 10logFPFD: PNSYNTH = PNTOT – 10logFPFD – 20logN.
8 The phase noise is measured with the EVAL-ADF411xEB and the HP8562E Spectrum Analyzer. The spectrum analyzer provides the REFIN for the synthesizer
(fREFOUT = 10 MHz @ 0 dBm).
9 fREFIN = 10 MHz; fPFD = 200 kHz; offset frequency = 1 kHz; fRF = 540 MHz; N = 2700; loop bandwidth = 20 kHz.
10
f
f
f
f
f
= 10 MHz; fPFD = 200 kHz; offset frequency = 1 kHz; fRF = 900 MHz; N = 4500; loop bandwidth = 20 kHz.
= 10 MHz; fPFD = 30 kHz; offset frequency = 300 Hz; fRF = 836 MHz; N = 27867; loop bandwidth = 3 kHz.
= 10 MHz; fPFD = 200 kHz; offset frequency = 1 kHz; fRF = 1750 MHz; N = 8750; loop bandwidth = 20 kHz.
= 10 MHz; fPFD = 10 kHz; offset frequency = 200 Hz; fRF = 1750 MHz; N = 175000; loop bandwidth = 1 kHz.
= 10 MHz; fPFD = 200 kHz; offset frequency = 1 kHz; fRF = 1960 MHz; N = 9800; loop bandwidth = 20 kHz.
REFIN
REFIN
REFIN
REFIN
REFIN
11
12
13
14
Rev. D | Page 4 of 28
ADF4116/ADF4117/ADF4118
TIMING CHARACTERISTICS
AVDD = DVDD = 3 V 10ꢀ, 5 V 10ꢀꢁ AVDD ≤ VP < 6.0 Vꢁ AGND = DGND = CPGND = 0 Vꢁ TA = TMIN to TMAX, unless otherwise noted.
Guaranteed by design, but not production tested.
Table 2.
Parameter
Limit at TMIN to TMAX (B, Y Version)
Unit
Test Conditions/Comments
DATA to CLK setup time
DATA to CLK hold time
CLK high duration
CLK low duration
CLK to LE setup time
LE pulse width
t1
t2
t3
t4
t5
t6
10
10
25
25
10
20
ns min
ns min
ns min
ns min
ns min
ns min
t3
t4
CLK
t1
t2
DB1
DB0 (LSB)
(CONTROL BIT C1)
DB20 (MSB)
DB19
DB2
DATA
LE
(CONTROL BIT C2)
t6
t5
LE
Figure 2. Timing Diagram
Rev. D | Page 5 of 28
ADF4116/ADF4117/ADF4118
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating onlyꢁ functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Table 3.
Parameter
AVDD to GND1
Rating
−0.3 V to +7 V
−0.3 V to +0.3 V
−0.3 V to +7 V
−0.3 V to +5.5 V
−0.3 V to VDD + 0.3 V
−0.3 V to VP + 0.3 V
−0.3 V to VDD + 0.3 V
320 mV
AVDD to DVDD
VP to GND1
VP to AVDD
This device is a high performance RF integrated circuit with an
ESD rating of <2 kV, and it is ESD sensitive. Proper precautions
should be taken for handling and assembly.
Digital I/O Voltage to GND1
Analog I/O Voltage to GND1
REFIN, RFINA, RFINB to GND1
RFINA to RFINB
Operating Temperature Range
Industrial (B Version)
Extended (Y Version)
Storage Temperature Range
Maximum Junction Temperature
TSSOP θJA Thermal Impedance
Reflow Soldering
ESD CAUTION
−40°C to +85°C
−40°C to +125°C
−65°C to +150°C
150°C
112°C/W
Peak Temperature
Time at Peak Temperature
Transistor Count
260°C
40 sec
CMOS
Bipolar
6425
303
1 GND = AGND = DGND = 0 V.
Rev. D | Page 6 of 28
ADF4116/ADF4117/ADF4118
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
FL
V
O
P
CP
CPGND
AGND
DV
DD
ADF4116/
ADF4117/
ADF4118
TOP VIEW
(Not to Scale)
MUXOUT
LE
RF
RF
B
A
DATA
CLK
IN
IN
AV
CE
DD
REF
DGND
IN
Figure 3. Pin Configuration
Table 4. Pin Function Descriptions
Pin No. Mnemonic Description
1
FLO
Fast Lock Switch Output. This can be used to switch an external resistor to change the loop filter bandwidth
and speed up locking the PLL.
2
CP
Charge Pump Output. When enabled, this provides the ICP to the external loop filter, which in turn drives the
external VCO.
3
4
5
CPGND
AGND
RFINB
Charge Pump Ground. This is the ground return path for the charge pump.
Analog Ground. This is the ground return path for the prescaler.
Complementary Input to the RF Prescaler. This point should be decoupled to the ground plane with a small
bypass capacitor, typically 100 pF. See Figure 26.
6
7
RFINA
AVDD
Input to the RF Prescaler. This small signal input is ac-coupled from the VCO.
Analog Power Supply. This can range from 2.7 V to 5.5 V. Decoupling capacitors to the analog ground plane
should be placed as close as possible to this pin. AVDD must have the same value as DVDD.
8
REFIN
Reference Input. This is a CMOS input with a nominal threshold of VDD/2 and an equivalent input resistance of 100 kΩ.
See Figure 25. The oscillator input can be driven from a TTL or CMOS crystal oscillator, or it can be ac-coupled.
9
10
DGND
CE
Digital Ground.
Chip Enable. A logic low on this pin powers down the device and puts the charge pump output into three-state
mode. Taking the pin high powers up the device depending on the status of the power-down bit F2.
11
12
13
14
15
CLK
Serial Clock Input. This serial clock is used to clock in the serial data to the registers. The data is latched into the
21-bit shift register on the CLK rising edge. This input is a high impedance CMOS input.
Serial Data Input. The serial data is loaded MSB first with the two LSBs as the control bits. This input is a high
impedance CMOS input.
Load Enable, CMOS Input. When LE goes high, the data stored in the shift registers is loaded into one of the four
latches, the latch being selected using the control bits.
This multiplexer output allows either the lock detect, the scaled RF, or the scaled reference frequency to be
accessed externally.
Digital Power Supply. This can range from 2.7 V to 5.5 V. Decoupling capacitors to the digital ground plane (1 μF, 1 nF)
should be placed as close as possible to this pin. For best performance, the 1 μF capacitor should be placed within 2 mm
of the pin. The placing of the 1 nF capacitor is less critical, but should still be within 5 mm of the pin.
DVDD must have the same value as AVDD.
DATA
LE
MUXOUT
DVDD
16
VP
Charge Pump Power Supply. This should be greater than or equal to VDD. In systems where VDD is 3 V, this supply can
be set to 6 V and used to drive a VCO with a tuning range of up to 6 V.
Rev. D | Page 7 of 28
ADF4116/ADF4117/ADF4118
TYPICAL PERFORMANCE CHARACTERISTICS
10dB/DIVISION
–40
R
= –40dBc/Hz
RMS NOISE = 0.64°
L
FREQ- PARAM-TYPE DATA-FORMAT KEYWORD IMPEDANCE-
UNIT
OHMS
–50
–60
GHz
S
MA
R
50
0.64° rms
FREQ
MagS11
AngS11
FREQ MagS11 AngS11
0.05
0.10
0.15
0.20
0.25
0.30
0.35
0.40
0.45
0.50
0.55
0.60
0.65
0.70
0.75
0.80
0.85
0.90
0.89207
0.8886
–2.0571
–4.4427
–6.3212
–2.1393
–12.13
0.95
1.00
1.05
1.10
1.15
1.20
1.25
1.30
1.35
1.40
1.45
1.50
1.55
1.60
1.65
1.70
1.75
1.80
0.92087
0.93788
0.9512
–36.961
–39.343
–40.134
–43.747
–44.393
–46.937
–49.6
–51.884
–51.21
–53.55
–56.786
–58.781
–60.545
–61.43
–61.241
–64.051
–66.19
–70
0.89022
0.96323
0.90566
0.90307
0.89318
0.89806
0.89565
0.88538
0.89699
0.89927
0.87797
0.90765
0.88526
0.81267
0.90357
0.92954
–80
0.93458
0.94782
0.96875
0.92216
0.93755
0.96178
0.94354
0.95189
0.97647
0.98619
0.95459
0.97945
0.98864
0.97399
0.97216
–13.52
–90
–15.746
–18.056
–19.693
–22.246
–24.336
–25.948
–28.457
–29.735
–31.879
–32.681
–31.522
–34.222
–100
–110
–120
–130
–140
100Hz
FREQUENCY OFFSET FROM 900MHz CARRIER
1MHz
–63.775
Figure 4. S-Parameter Data for the ADF4118 RF Input (Up to 1.8 GHz)
Figure 7. ADF4118 Integrated Phase Noise
(900 MHz, 200 kHz, 35 kHz, Typical Lock Time: 200 μs)
0
10dB/DIVISION
–40
R
= –40dBc/Hz
RMS NOISE = 0.575°
L
–5
V
V
= 3V
= 3V
DD
–50
–60
P
0.575° rms
–10
–15
–20
–25
–70
–80
–90
T
T
= –40°C
= +25°C
A
A
–100
–30
–35
–110
–120
–130
T
= +85°C
3.5
A
–40
–45
0
0.5
1.0
1.5
2.0
2.5
3.0
4.0
–140
100Hz
FREQUENCY OFFSET FROM 900MHz CARRIER
1MHz
RF INPUT FREQUENCY (GHz)
Figure 5. Input Sensitivity (ADF4118)
Figure 8. ADF4118 Integrated Phase Noise
(900 MHz, 200 kHz, 20 kHz, Typical Lock Time: 400 μs)
0
–10
–20
–30
–40
–50
0
REFERENCE
LEVEL = –3.8dBm
V
I
= 3V, V = 5V
P
REFERENCE
LEVEL = –4.2dBm
V
I
= 3V, V = 5V
P
DD
DD
–10
–20
–30
–40
–50
= 1mA
= 1mA
CP
CP
PFD FREQUENCY = 200kHz
LOOP BANDWIDTH = 20kHz
RES. BANDWIDTH = 1kHz
VIDEO BANDWIDTH = 1kHz
SWEEP = 2.5 SECONDS
AVERAGES = 4
PFD FREQUENCY = 200kHz
LOOP BANDWIDTH = 20kHz
RES. BANDWIDTH = 10Hz
VIDEO BANDWIDTH = 10Hz
SWEEP = 1.9 SECONDS
AVERAGES = 22
–60
–70
–60
–70
–90.2dBc/Hz
–91.5dBc
–80
–80
–90
–90
–100
–100
–400kHz
–200kHz
900MHz
200kHz
400kHz
–2kHz
–1kHz
900MHz
1kHz
2kHz
Figure 9. ADF4118 Reference Spurs
(900 MHz, 200 kHz, 20 kHz)
Figure 6. ADF4118 Phase Noise
(900 MHz, 200 kHz, 20 kHz)
Rev. D | Page 8 of 28
ADF4116/ADF4117/ADF4118
0
0
–10
–20
–30
–40
–50
V
I
= 3V, V = 5V
P
V
I
= 3V, V = 5V
P
DD
DD
REFERENCE
LEVEL = –4.2dBm
REFERENCE
LEVEL = –7.0dBm
–10
–20
–30
–40
–50
= 5mA
= 1mA
CP
CP
PFD FREQUENCY = 30kHz
LOOP BANDWIDTH = 5kHz
RES. BANDWIDTH = 300Hz
VIDEO BANDWIDTH = 300Hz
SWEEP = 4.2ms
PFD FREQUENCY = 200kHz
LOOP BANDWIDTH = 35kHz
RES. BANDWIDTH = 1kHz
VIDEO BANDWIDTH = 1kHz
SWEEP = 2.5 SECONDS
AVERAGES = 10
AVERAGES = 20
–60
–70
–60
–70
–72.3dBc
–90.67dBc
–80
–90
–80
–90
–100
–100
–400kHz
–200kHz
900MHz
200kHz
400kHz
–60kHz
–30kHz
1750MHz
30kHz
60kHz
Figure 10. ADF4118 Reference Spurs
(900 MHz, 200 kHz, 35 kHz)
Figure 13. ADF4118 Reference Spurs
(1750 MHz, 30 kHz, 3 kHz)
0
–10
–20
–30
–40
–50
0
V
= 3V, V = 5V
P
DD
REFERENCE
LEVEL = –7.0dBm
V
= 3V, V = 5V
DD P
REFERENCE
LEVEL = –10.3dBm
I
= 1mA
CP
–10
–20
–30
–40
I
= 1mA
CP
PFD FREQUENCY = 30kHz
LOOP BANDWIDTH = 5kHz
RES. BANDWIDTH = 10kHz
VIDEO BANDWIDTH = 10kHz
SWEEP = 477ms
PFD FREQUENCY = 1MHz
LOOP BANDWIDTH = 100kHz
RES. BANDWIDTH = 10Hz
VIDEO BANDWIDTH = 10Hz
SWEEP = 1.9 SECONDS
AVERAGES = 26
–50
AVERAGES = 25
–60
–70
–60
–70
–85.2dBc/Hz
–71.5dBc/Hz
–80
–80
–90
–90
–100
–100
–400kHz
–200kHz
1750MHz
200kHz
400kHz
–2kHz
–1kHz
1kHz
2kHz
2800MHz
Figure 11. ADF4118 Phase Noise
(1750 MHz, 30 kHz, 3 kHz)
Figure 14. ADF4118 Phase Noise
(2800 MHz, 1 MHz, 100 kHz)
10dB/DIVISION
–40
R
= –40dBc/Hz
RMS NOISE = 2.0°
10dB/DIVISION
–40
R
= –40dBc/Hz
RMS NOISE = 1.552°
L
L
–50
–60
–50
–60
1.55° rms
2.0° rms
–70
–80
–70
–80
–90
–90
–100
–100
–110
–120
–130
–110
–120
–130
–140
100Hz
–140
100Hz
FREQUENCY OFFSET FROM 1.75GHz CARRIER
1MHz
FREQUENCY OFFSET FROM 2.8GHz CARRIER
1MHz
Figure 15. ADF4118 Integrated Phase Noise
(2800 MHz, 1 MHz, 100 kHz)
Figure 12. ADF4118 Integrated Phase Noise
(1750 MHz, 30 kHz, 3 kHz)
Rev. D | Page 9 of 28
ADF4116/ADF4117/ADF4118
0
–60
–70
V
I
= 3V, V = 5V
P
DD
REFERENCE
LEVEL = –9.3dBm
–10
–20
–30
–40
–50
= 1mA
V
V
= 3V
CP
DD
= 5V
P
PFD FREQUENCY = 1MHz
LOOP BANDWIDTH = 100kHz
RES. BANDWIDTH = 3kHz
VIDEO BANDWIDTH = 3kHz
SWEEP = 1.4 SECONDS
AVERAGES = 4
–80
–60
–70
–77.3dBc
–90
–80
–90
–100
–100
–40
–20
0
20
40
60
80
100
–2MHz
–1MHz
2800MHz
1MHz
2MHz
TEMPERATURE (°C)
Figure 16. ADF4118 Reference Spurs
(2800 MHz, 1 MHz, 100 kHz)
Figure 19. ADF4118 Reference Spurs vs. Temperature
(900 MHz, 200 kHz, 20 kHz)
–130
–135
–140
–145
–150
–155
–160
–165
–170
–175
5
–5
V
V
= 3V
DD
= 5V
V
V
= 3V
DD
= 5V
P
P
–15
–25
–35
–45
–55
–65
–75
–85
–95
–105
0
1
2
3
4
5
1
10
100
1000
10000
PHASE DETECTOR FREQUENCY (kHz)
TUNING VOLTAGE
Figure 17. ADF4118 Phase Noise (Referred to CP Output) vs.
PFD Frequency
Figure 20. ADF4118 Reference Spurs (200 kHz) vs. VTUNE
(900 MHz, 200 kHz, 20 kHz)
–60
–60
–70
–80
–90
V
V
= 3V
DD
= 5V
V
V
= 3V
P
DD
= 5V
P
–70
–80
–90
–100
0
20
40
60
80
100
–40
–20
0
20
40
60
80
100
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 18. ADF4118 Phase Noise vs. Temperature
(900 MHz, 200 kHz, 20 kHz)
Figure 21. ADF4118 Phase Noise vs. Temperature
(836 MHz, 30 kHz, 3 kHz)
Rev. D | Page 10 of 28
ADF4116/ADF4117/ADF4118
–60
–70
1.2
1.0
0.8
0.6
V
V
= 3V
DD
= 5V
V
= 5V
SETTING: 1mA
P
P
I
CP
0.4
0.2
–80
0
–0.2
–0.4
–0.6
–0.8
–1.0
–1.2
–90
–100
0
20
40
60
80
100
0
0.5
1.0
1.5
2.0
2.5
(V)
3.0
3.5
4.0
4.5
5.0
TEMPERATURE (°C)
V
CP
Figure 22. ADF4118 Reference Spurs vs. Temperature
(836 MHz, 30 kHz, 3 kHz)
Figure 24. Charge Pump Output Characteristics
3.0
2.5
2.0
1.5
1.0
0.5
0
0
50
100
150
200
PRESCALER OUTPUT FREQUENCY (MHz)
Figure 23. DIDD vs. Prescaler Output Frequency
Rev. D | Page 11 of 28
ADF4116/ADF4117/ADF4118
CIRCUIT DESCRIPTION
REFERENCE INPUT SECTION
A COUNTER AND B COUNTER
The A CMOS counter and B CMOS counter combine with the
dual-modulus prescaler to allow a wide ranging division ratio in
the PLL feedback counter. The counters are specified to work
when the prescaler output is 200 MHz or less.
The reference input stage is shown in Figure 25. SW1 and SW2
are normally closed switchesꢁ SW3 is normally open. When
power-down is initiated, SW3 is closed and SW1 and SW2 are
opened. This ensures that there is no loading of the REFIN pin
on power-down.
Pulse Swallow Function
POWER-DOWN
CONTROL
The A counter and B counter, in conjunction with the dual-
modulus prescaler, make it possible to generate output
frequencies that are spaced only by the reference frequency
divided by R. The equation for the VCO frequency is as follows:
100kΩ
NC
SW2
TO R COUNTER
REF
IN
NC
SW1
BUFFER
fVCO
where:
VCO is the output frequency of external voltage controlled
=
(P×B)+ A × fREFIN /R
[ ]
SW3
NO
Figure 25. Reference Input Stage
f
oscillator (VCO).
RF INPUT STAGE
P is the preset modulus of dual-modulus prescaler.
B is the preset divide ratio of binary 13-bit counter (3 to 8191).
A is the preset divide ratio of binary 5-bit swallow counter (0 to 31).
The RF input stage is shown in Figure 26. It is followed by a
2-stage limiting amplifier to generate the CML clock levels
needed for the prescaler.
f
REFIN is the output frequency of the external reference frequency
oscillator.
1.6V
BIAS
GENERATOR
AV
DD
R is the preset divide ratio of binary 14-bit programmable
reference counter (1 to 16,383).
500Ω
500Ω
R COUNTER
RF
RF
A
B
IN
The 14-bit R counter allows the input reference frequency to be
divided down to produce the input clock to the phase frequency
detector (PFD). Division ratios from 1 to 16,383 are allowed.
IN
AGND
N = BP + A
TO PFD
13-BIT
Figure 26. RF Input Stage
B COUNTER
FROM RF
PRESCALER (P/P + 1)
LOAD
LOAD
INPUT STAGE
PRESCALER
P/P + 1
The dual-modulus prescaler (P/P + 1), along with the A counter
and B counter, enables the large division ratio, N, to be realized
(N = PB + A). The dual-modulus prescaler takes the CML clock
from the RF input stage and divides it down to a manageable
frequency for the CMOS A counter and CMOS B counter. The
prescaler is programmable. It can be set in software to 8/9 for the
ADF4116 and to 32/33 for the ADF4117 and ADF4118. It is based
on a synchronous 4/5 core.
MODULUS
CONTROL
5-BIT
A COUNTER
Figure 27. A Counter and B Counter
Rev. D | Page 12 of 28
ADF4116/ADF4117/ADF4118
PHASE FREQUENCY DETECTOR (PFD)
AND CHARGE PUMP
MUXOUT AND LOCK DETECT
The output multiplexer on the ADF411x family allows the user
to access various internal points on the chip. The state of
MUXOUT is controlled by M3, M2, and M1 in the function
latch. Figure 33 shows the full truth table. Figure 29 shows the
MUXOUT section in block diagram form.
The PFD takes inputs from the R counter and N counter and
produces an output proportional to the phase and frequency
difference between them. Figure 28 is a simplified schematic of
the PFD. The PFD includes a fixed delay element that sets the
width of the antibacklash pulse. This is typically 3 ns. This pulse
ensures that there is no dead zone in the PFD transfer function
and gives a consistent reference spur level.
DV
DD
V
P
ANALOG LOCK DETECT
DIGITAL LOCK DETECT
CHARGE
PUMP
MUXOUT
R COUNTER OUTPUT
N COUNTER OUTPUT
SDOUT
MUX
CONTROL
UP
HI
D1
Q1
U1
R DIVIDER
CLR1
DGND
Figure 29. MUXOUT Circuit
CP
DELAY
DOWN
U3
Lock Detect
MUXOUT can be programmed for both digital lock detect and
analog lock detect.
CLR2
U2
Digital lock detect is active high. It is set high when the phase
error on three consecutive phase detector cycles is less than
15 ns. It stays set high until a phase error greater than 25 ns is
detected on any subsequent PD cycle.
D2
Q2
HI
N DIVIDER
CPGND
The N channel, open-drain, analog lock detect should be
operated with an external pull-up resistor of 10 kΩ nominal.
When lock is detected, it is high with narrow low going pulses.
R DIVIDER
N DIVIDER
INPUT SHIFT REGISTER
CP OUTPUT
The ADF411x family digital section includes a 21-bit input shift
register, a 14-bit R counter, and an 18-bit N counter, comprising
a 5-bit A counter and a 13-bit B counter. Data is clocked into
the 21-bit shift register on each rising edge of CLK. The data is
clocked in MSB first. Data is transferred from the shift register
to one of four latches on the rising edge of LE. The destination
latch is determined by the state of the two control bits (C2, C1)
in the shift register. These are the two LSBs, DB1 and DB0, as
shown in the timing diagram in Figure 2. The truth table for
these bits is shown in Figure 34. Table 5 summarizes how the
latches are programmed.
Figure 28. PFD Simplified Schematic and Timing (In Lock)
Table 5. Programming Data Latches
Control Bits
C2
0
C1
0
Data Latch
R Counter
0
1
1
1
0
1
N Counter (A and B)
Function Latch
Initialization Latch
Rev. D | Page 13 of 28
ADF4116/ADF4117/ADF4118
LATCH SUMMARIES
REFERENCE COUNTER LATCH
TEST
MODE BITS
CONTROL
BITS
14-BIT REFERENCE COUNTER, R
DB20
LDP
DB19 DB18 DB17 DB16 DB15 DB14
T4 T3 T2 T1 R14 R13
DB13
R12
DB12 DB11 DB10
R11 R10 R9
DB9
R8
DB8
R7
DB7
R6
DB6
R5
DB5
R4
DB4
R3
DB3
R2
DB2
R1
DB1
DB0
C2 (0) C1 (0)
AB COUNTER LATCH
CONTROL
BITS
13-BIT B COUNTER
5-BIT A COUNTER
DB20 DB19 DB18
G1 B13 B12
DB17 DB16 DB15 DB14 DB13 DB12
DB11 DB10
B5 B4
DB9
B3
DB8
B2
DB7
B1
DB6
A5
DB5
DB4
A3
DB3
DB2
A1
DB1
DB0
B11
B10
B9
B8
B7
B6
A4
A2
C2 (0) C1 (1)
FUNCTION LATCH
TIMER COUNTER
CONTROL
MUXOUT
CONTROL
CONTROL
BITS
RESERVED
DB20 DB19
PD2
DB18 DB17 DB16 DB15 DB14
DB13 DB12
DB11 DB10
F6
DB9
F4
DB8
F3
DB7
F2
DB6
M3
DB5
M2
DB4
M1
DB3
PD1
DB2
F1
DB1
DB0
X
X
X
X
TC4
TC3
TC2
TC1
X
C2 (1) C1 (0)
INITIALIZATION LATCH
TIMER COUNTER
CONTROL
MUXOUT
CONTROL
CONTROL
BITS
RESERVED
DB20 DB19
DB18 DB17 DB16 DB15 DB14 DB13 DB12
DB11 DB10
F6
DB9
F4
DB8
F3
DB7
F2
DB6
M3
DB5
M2
DB4
M1
DB3
PD1
DB2
F1
DB1
DB0
X
X
X
X
PD2
TC4
TC3
TC2
TC1
X
C2 (1) C1 (1)
Figure 30. ADF411x family Latch Summary
Rev. D | Page 14 of 28
ADF4116/ADF4117/ADF4118
LATCH MAPS
TEST
MODE BITS
CONTROL
BITS
14-BIT REFERENCE COUNTER, R
DB20 DB19 DB18 DB17
LDP T4 T3 T2
DB16 DB15 DB14 DB13 DB12
T1 R14 R13 R12 R11
DB11 DB10
DB9
R8
DB8
R7
DB7
R6
DB6
R5
DB5
R4
DB4
R3
DB3
R2
DB2
R1
DB1
DB0
R10
R9
C2 (0) C1 (0)
R14
0
R13
0
R12
0
••••••••••
••••••••••
R3
R2
0
R1
1
DIVIDE RATIO
1
0
0
0
1
•
0
0
0
•
0
0
0
•
0
0
0
•
••••••••••
••••••••••
••••••••••
••••••••••
••••••••••
••••••••••
••••••••••
••••••••••
••••••••••
••••••••••
1
1
0
•
0
1
0
•
2
3
4
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
1
1
0
1
0
1
163 80
163 81
163 82
163 83
TEST MODE BITS SHOULD
BE SET TO 0000 FOR
NORMAL OPERATION
LDP
OPERATION
3 CONSECUTIVE CYCLES OF PHASE DELAY LESS THAN
15ns MUST OCCUR BEFORE LOCK DETECT IS SET.
5 CONSECUTIVE CYCLES OF PHASE DELAY LESS THAN
15ns MUST OCCUR BEFORE LOCK DETECT IS SET.
0
1
Figure 31. Reference Counter Latch Map
Rev. D | Page 15 of 28
ADF4116/ADF4117/ADF4118
CONTROL
BITS
13-BIT B COUNTER
5-BIT A COUNTER
DB20
G1
DB19 DB18
B13 B12
DB17 DB16 DB15 DB14
DB13 DB12
B7 B6
DB11 DB10
DB9
B3
DB8
B2
DB7
B1
DB6
A5
DB5
A4
DB4
A3
DB3
DB2
A1
DB1
DB0
B11
B10
B9
B8
B5
B4
A2
C2 (0) C1 (1)
A COUNTER
DIVIDE RATIO
A5
A4
X
X
•
A3
A2
A1
0
1
•
X
X
•
0
0
•
0
0
•
0
1
•
ADF4116
•
•
•
•
•
•
X
X
X
X
1
1
1
1
0
1
6
7
A COUNTER
DIVIDE RATIO
A5
0
0
0
•
A4
0
0
0
•
A3
0
0
0
•
A2
0
0
1
•
A1
0
1
0
•
0
1
ADF4117/ADF4118
2
•
•
•
•
•
•
•
1
1
1
1
1
1
1
1
1
0
1
1
1
0
1
29
30
31
••••••••••
••••••••••
B13
B12
0
B11
0
B3
0
B2
0
B1
1
B COUNTER DIVIDE RATIO
NOT ALLOWED
0
0
0
0
•
0
0
0
•
0
0
0
•
••••••••••
••••••••••
••••••••••
••••••••••
••••••••••
••••••••••
••••••••••
••••••••••
••••••••••
••••••••••
0
0
1
•
1
1
0
•
0
1
0
•
NOT ALLOWED
3
4
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
1
1
0
1
0
1
8188
8189
8190
8191
LDP CURRENT SETTINGS
250µA
1mA
0
1
N = BP + A, P IS PRESCALER VALUE. B MUST BE GREATER
THAN OR EQUAL TO A. FOR CONTINUOUSLY ADJACENT
2
VALUES OF N
F
, N
IS (P – P).
MIN
X
REF
Figure 32. A Counter/B Counter Latch Map
Rev. D | Page 16 of 28
ADF4116/ADF4117/ADF4118
TIMER COUNTER
CONTROL
MUXOUT
CONTROL
CONTROL
BITS
RESERVED
DB20
X
DB19 DB18
PD2
DB17 DB16 DB15 DB14
DB13 DB12 DB11 DB10
DB9
F4
DB8
F3
DB7
F2
DB6
M3
DB5
M2
DB4
M1
DB3
PD1
DB2
F1
DB1
DB0
X
X
X
TC4
TC3
TC2
TC1
F6
X
C2 (1) C1 (0)
COUNTER
OPERATION
F1
0
NORMAL
R, A, B COUNTERS
HELD IN RESET
1
CE PIN PD2 PD1
MODE
M3
M2
0
M1
OUTPUT
ASYNCHRONOUS POWER-DOWN
NORMAL OPERATION
0
1
1
1
X
X
0
1
X
0
1
1
0
0
THREE-STATE OUTPUT
DIGITAL LOCK DETECT
(ACTIVE HIGH)
ASYNCHRONOUS POWER-DOWN
SYNCHRONOUS POWER-DOWN
0
0
0
1
0
1
1
0
1
0
1
0
N DIVIDER OUTPUT
AV
DD
R DIVIDER OUTPUT
ANALOG LOCK DETECT
(N CHANNEL OPEN DRAIN)
1
0
1
SERIAL DATA OUTPUT
(INVERSE POLARITY OF
SERIAL DATA INPUT)
1
1
1
1
0
1
DGND
PHASE DETECTOR
POLARITY
F2
0
NEGATIVE
1
POSITIVE
CHARGE PUMP
OUTPUT
F3
0
NORMAL
1
THREE-STATE
F4
0
F6
X
FASTLOCK MODE
FASTLOCK DISABLED
FASTLOCK MODE 1
FASTLOCK MODE 2
TIMEOUT
1
0
1
1
TC4
TC3
TC2
TC1
(PFD CYCLES)
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
3
7
11
15
19
23
27
31
35
39
43
47
51
55
59
63
Figure 33. Function Latch Map
Rev. D | Page 17 of 28
ADF4116/ADF4117/ADF4118
RESERVED
TIMER COUNTER
MUXOUT
CONTROL
CONTROL
BITS
CONTROL
DB20 DB19
DB18 DB17
DB16
X
DB15 DB14 DB13 DB12
DB11 DB10
F6
DB9
F4
DB8
F3
DB7
F2
DB6
M3
DB5
M2
DB4
M1
DB3
PD1
DB2
F1
DB1
DB0
X
X
X
PD2
TC4
TC3
TC2
TC1
X
C2 (1) C1 (1)
COUNTER
OPERATION
F1
0
1
NORMAL
R, A, B COUNTERS
HELD IN RESET
M3
M2
0
M1
OUTPUT
CE PIN PD2 PD1
MODE
0
0
THREE-STATE OUTPUT
ASYNCHRONOUS POWER-DOWN
NORMAL OPERATION
0
1
1
1
X
X
0
1
X
0
1
1
DIGITAL LOCK DETECT
(ACTIVE HIGH)
0
0
1
1
0
1
0
1
0
ASYNCHRONOUS POWER-DOWN
N DIVIDER OUTPUT
0
SYNCHRONOUS POWER-DOWN
AV
DD
0
1
R DIVIDER OUTPUT
ANALOG LOCK DETECT
(N CHANNEL OPEN DRAIN)
1
0
1
SERIAL DATA OUTPUT
(INVERSE POLARITY OF
SERIAL DATA INPUT)
1
1
1
1
0
1
DGND
PHASE DETECTOR
POLARITY
F2
0
NEGATIVE
1
POSITIVE
CHARGE PUMP
OUTPUT
F3
0
NORMAL
1
THREE-STATE
F4
0
F6
FASTLOCK MODE
FASTLOCK DISABLED
X
0
1
FASTLOCK MODE 1
FASTLOCK MODE 2
1
1
TIMEOUT
(PFD CYCLES)
TC4
TC3
TC2
TC1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
3
7
11
15
19
23
27
31
35
39
43
47
51
55
59
63
Figure 34. Initialization Latch Map
Rev. D | Page 18 of 28
ADF4116/ADF4117/ADF4118
FUNCTION LATCH
With C2 and C1 set to 1 and 0, respectively, the on-chip
function latch is programmed. Figure 33 shows the input data
format for programming the function latch.
CHARGE PUMP THREE-STATE
The DB8 (F3) bit puts the charge pump into three-state mode
when programmed to 1. It should be set to 0 for normal operation.
COUNTER RESET
FASTLOCK ENABLE BIT
DB2 (F1) is the counter reset bit. When this bit is set to 1, the R
counter, A counter, and B counter are reset. For normal operation,
this bit should be set to 0. On power-up, the F1 bit needs to be
disabled, for the N counter to resume counting in “close”
alignment with the R counter. (The maximum error is one
prescaler cycle.)
DB9 (F4) of the function latch is the fastlock enable bit. Fastlock
is enabled only when DB9 is set to 1.
FASTLOCK MODE BIT
DB11 (F6) of the function latch is the fastlock mode bit. When
fastlock is enabled, this bit determines which fastlock mode is
used. If the fastlock mode bit is 0, Fastlock Mode 1 is selectedꢁ if
the fastlock mode bit is 1, Fastlock Mode 2 is selected.
POWER-DOWN
DB3 (PD1) and DB19 (PD2) on the ADF411x family provide
programmable power-down modes. They are enabled by the
CE pin.
If fastlock is not enabled (DB9 = 0), DB11 (ADF4116)
determines the state of the FLO output. FLO state is the same as
that programmed to DB11.
When the CE pin is low, the device is immediately disabled
regardless of the states of PD2 and PD1.
Fastlock Mode 1
In the ADF411x family, the output level of FLO is programmed
to a low state, and the charge pump current is switched to the
high value (1 mA). FLO is used to switch a resistor in the loop
filter and to ensure stability while in fastlock by altering the
loop bandwidth.
In programmed asynchronous power-down, the device powers
down immediately after latching a 1 into the PD1 bit, with the
condition that PD2 is loaded with a 0.
In programmed synchronous power-down, the device power-
down is gated by the charge pump to prevent unwanted
frequency jumps. Once power-down is enabled by writing a 1
into the PD1 bit (on condition that a 1 is also loaded to PD2),
the device goes into power-down after the first successive
charge pump event.
The device enters fastlock by having a 1 written to the CP Gain
bit in the N register. The device exits fastlock by having a 0
written to the CP Gain bit in the N register.
Fastlock Mode 2
In the ADF411x family, the output level of FLO is programmed
to a low state, and the charge pump current is switched to the
high value (1 mA). FLO is used to switch a resistor in the loop
filter and to ensure stability while in fastlock by altering the
loop bandwidth.
When a power-down is activated (either synchronous or
asynchronous mode including CE pin-activated power-down),
the following events occur:
•
•
All active dc current paths are removed.
The R counter, N counter, and timeout counter are forced
to their load state conditions.
The device enters fastlock by having a 1 written to the CP gain
bit in the N register. The device exits fastlock under the control
of the timer counter. After the timeout period determined by
the value in TC4 to TC1, the CP Gain bit in the N register is
automatically reset to 0, and the device reverts to normal mode
instead of fastlock.
•
•
•
•
•
The charge pump is forced into three-state mode.
The digital clock detect circuitry is reset.
The RFIN input is debiased.
The oscillator input buffer circuitry is disabled.
TIMER COUNTER CONTROL
The input register remains active and capable of loading
and latching data.
In the ADF411x family, the user has the option of switching
between two charge pump current values to speed up locking to
a new frequency.
MUXOUT CONTROL
When using the fastlock feature with the ADF411x family, the
following should be noted:
The on-chip multiplexer is controlled by DB6 (M3), DB5 (M2),
and DB4 (M1) on the ADF411x family. Figure 33 shows the
truth table.
•
The user must make sure that fastlock is enabled. Set DB9
to 1. The user must also choose which fastlock mode to use.
PHASE DETECTOR POLARITY
DB7 (F2) of the function latch sets the phase detector polarity.
When the VCO characteristics are positive, DB7 should be set
to 1. When they are negative, it should be set to 0.
Rev. D | Page 19 of 28
ADF4116/ADF4117/ADF4118
4. Do an N load (01 in 2 LSBs).
•
Fastlock Mode 2 uses the values in the timer counter to
determine the timeout period before reverting to normal
mode operation after fastlock. Fastlock Mode 2 is chosen
by setting DB11 to 1.
When the initialization latch is loaded, the following occurs:
•
•
The function latch contents are loaded.
An internal pulse resets the R, N, and timeout counters to
load state conditions and also three-states the charge pump.
Note that the prescaler band gap reference and the oscillator
input buffer are unaffected by the internal reset pulse, allowing
close phase alignment when counting resumes.
•
The user must also decide how long to keep the high
current (1 mA) active before reverting to low current
(250 μA). This is controlled by the timer counter control
bits, DB14 to DB11 (TC4 to TC1), in the function latch.
The truth table is given in Figure 33.
•
Latching the first N counter data after the initialization
word activates the same internal reset pulse. Successive
N loads do not trigger the internal reset pulse unless there
is another initialization.
•
To program a new output frequency, program the A counter
and B counter latch with new values for A and B. At the
same time, set the CP Gain bit to a 1, which sets the charge
pump to 1 mA for a period of time determined by TC4 to
TC1. When this time is up, the charge pump current
reverts to 250 μA. At the same time, the CP Gain bit in the
A counter and B counter latch is reset to 0 and is ready for
the next time that the user wants to change the frequency.
CE Pin Method
1. Apply VDD
.
2. Bring CE low to put the device into power-down. This is an
asynchronous power-down in that it happens immediately.
INITIALIZATION LATCH
3. Program the function latch (10).
When C2 and C1 are both set to 1, the initialization latch is
programmed. This is essentially the same as the function latch
that is programmed when C2, C1 = 1, 0.
4. Program the R counter latch (00).
5. Program the N counter latch (01).
6. Bring CE high to take the device out of power-down.
The R counter and N counter resume counting in close alignment.
However, when the initialization latch is programmed, an
additional internal reset pulse is applied to the R counter and
N counter. This pulse ensures that the N counter is at a load
point when the N counter data is latched and that the device
begins counting in close phase alignment.
Note that after CE goes high, a duration of 1 μs may be required
for the prescaler band gap voltage and oscillator input buffer
bias to reach a steady state.
If the latch is programmed for synchronous power-down (CE
pin is highꢁ PD1 bit is highꢁ PD2 bit is low), the internal pulse
also triggers this power-down. The prescaler reference and the
oscillator input buffer are unaffected by the internal reset pulse,
so close phase alignment is maintained when counting resumes.
CE can be used to power up and power down the device to check
for channel activity. The input register does not need to be repro-
grammed each time the device is disabled and enabled, as long
as it is programmed at least once after VCC is initially applied.
Counter Reset Method
When the first N counter data is latched after initialization, the
internal reset pulse is again activated. However, successive
N counter loads do not trigger the internal reset pulse.
1. Apply VDD
.
2. Do a function latch load (10 in 2 LSBs). As part of this,
load 1 to the F1 bit. This enables the counter reset.
DEVICE PROGRAMMING AFTER
INITIAL POWER-UP
3. Do an R counter load (00 in 2 LSBs).
4. Do an N counter load (01 in 2 LSBs).
After initial power-up, the device can be programmed by the
initialization latch method, the CE pin method, or the counter
reset method.
5. Do a function latch load (10 in 2 LSBs). As part of this,
load 0 to the F1 bit. This disables the counter reset.
Initialization Latch Method
This sequence provides the same close alignment as the initiali-
zation method. It offers direct control over the internal reset.
Note that counter reset holds the counters at load point and
three-states the charge pump, but it does not trigger synchro-
nous power-down. The counter reset method requires an extra
function latch load compared to the initialization latch method.
1. Apply VDD
.
2. Program the initialization latch (11 in 2 LSBs of input
word). Make sure that F1 bit is programmed to 0.
3. Do an R load (00 in 2 LSBs).
Rev. D | Page 20 of 28
ADF4116/ADF4117/ADF4118
APPLICATIONS INFORMATION
LOCAL OSCILLATOR FOR THE
SHUTDOWN CIRCUIT
GSM BASE STATION TRANSMITTER
The attached circuit in Figure 36 shows how to shut down both
the ADF411x family and the accompanying VCO. The ADG702
switch goes open-circuit when a Logic 1 is applied to the IN
input. The low cost switch is available in both SOT-23 and
MSOP packages.
Figure 35 shows the ADF4117/ADF4118 being used with a
VCO to produce the LO for a GSM base station transmitter.
The reference input signal is applied to the circuit at FREFIN and,
in this case, is terminated in 50 Ω. A typical GSM system has a
13 MHz TCXO driving the reference input without a 50 Ω
termination. To have a channel spacing of 200 kHz (the GSM
standard), the reference input must be divided by 65, using the
on-chip reference divider of the ADF4117/ADF1118.
DIRECT CONVERSION MODULATOR
In some applications, a direct conversion architecture can be
used in base station transmitters. Figure 37 shows the
combination available from Analog Devices, Inc. to implement
this solution.
The charge pump output of the ADF4117/ADF1118 (Pin 2)
drives the loop filter. In calculating the loop filter component
values, a number of items need to be considered. In this example,
the loop filter was designed so that the overall phase margin for
the system is 45°. Other PLL system specifications include:
The circuit diagram shows the AD9761 being used with the
AD8346. The use of dual integrated DACs, such as the AD9761
with specified 0.02 dB and 0.004 dB gain and offset matching
characteristics, ensures minimum error contribution (over
temperature) from this portion of the signal chain.
KD = 1 mA
KV = 12 MHz/V
Loop bandwidth = 20 kHz
FREF = 200 kHz
The local oscillator is implemented by using the ADF4117/
ADF4118. In this case, the FOX801BH-130 provides the stable
13 MHz reference frequency. The system is designed for
200 kHz channel spacing and an output center frequency of
1960 MHz. The target application is a WCDMA base station
transmitter. Typical phase noise performance from this LO is
−85 dBc/Hz at a 1 kHz offset. The LO port of the AD8346 is
driven in single-ended fashion. LOIN is ac-coupled to ground
with the 100 pF capacitor, and LOIP is driven through the ac-
coupling capacitor from a 50 Ω source. An LO drive level between
−6 dBm and −12 dBm is required. The circuit in Figure 37 gives a
typical level of −8 dBm.
N = 4500
Extra reference spur attenuation = 10 dB
All of these specifications are needed and are used to produce
the loop filter component values shown in Figure 36.
The loop filter output drives the VCO, which, in turn, is fed back
to the RF input of the PLL synthesizerꢁ it also drives the RF
output terminal. A T-circuit configuration provides 50 Ω
matching between the VCO output, the RF output, and the
RFIN terminal of the synthesizer.
The RF output is designed to drive a 50 Ω load, but it must be
ac-coupled as shown in Figure 37. If the I and Q inputs are
driven in quadrature by 2 V p-p signals, the resulting output
power is approximately −10 dBm.
In a PLL system, it is important to know when the system is in
locked mode. In Figure 35, this is accomplished by using the
MUXOUT signal from the synthesizer. The MUXOUT pin can
be programmed to monitor various internal signals in the
synthesizer. One of these is the LD or lock-detect signal.
Rev. D | Page 21 of 28
ADF4116/ADF4117/ADF4118
RF
OUT
V
V
DD
P
100pF
7
15 16
DV
AV
V
P
18Ω
DD
DD
V
3.3kΩ
CC
2
1
100pF
18Ω
1000pF
1000pF
8
CP
F
REF
REFIN
IN
VCO190-902T
620pF
18Ω
27kΩ
0.15nF
51Ω*
FL
O
ADF4117/
ADF4118
10kΩ
1.5nF
14
CE
LOCK
DETECT
MUXOUT
CLK
DATA
LE
100pF
6
5
RF
RF
A
IN
51Ω**
B
IN
100pF
*TO BE USED WHEN GENERATOR SOURCE IMPEDANCE IS 50Ω.
**OPTIONAL MATCHING RESISTOR DEPENDING ON RF FREQUENCY.
3
4
9
OUT
DECOUPLING CAPACITORS ON AV , DV , AND V OF THE
DD DD
P
ADF4117/ADF4118 AND ON V OF THE VCO190-920T HAVE BEEN
CC
OMITTED FROM THE DIAGRAM FOR CLARITY.
Figure 35. Local Oscillator for GSM Base Station
V
P
POWER-DOWN CONTROL
S
V
DD
RF
OUT
IN
V
7
ADG702
GND
DD
D
100pF
15 16
18Ω
18Ω
V
100pF
AV
DV
DD
V
CE
CC
18Ω
DD
P
2
1
LOOP
FILTER
8
CP
O
F
REF
REFIN
IN
VCO
FL
GND
10kΩ
ADF4116/
ADF4117/
ADF4118
100pF
6
5
RF
RF
A
IN
51Ω
B
IN
100pF
3
4
9
DECOUPLING CAPACITORS AND INTERFACE SIGNALS HAVE
BEEN OMITTED FROM THE DIAGRAM FOR CLARITY.
Figure 36. Local Oscillator Shutdown Circuit
Rev. D | Page 22 of 28
ADF4116/ADF4117/ADF4118
0.1µF
REFIO
IBBP
IBBP
IOUTA
IOUTB
100pF
LOW-PASS
FILTER
RF
VOUT
OUT
MODULATED
DIGITAL
DATA
AD9761
TxDAC
AD8346
QBBP
QBBP
QOUTA
QOUTB
LOW-PASS
FILTER
FS ADJ
2kΩ
LOIN
LOIP
100pF
100pF
FOX801BH-130
TCXO
18Ω
10kΩ
1kΩ
REF
IN
CP
VCO190-1960T
18pF
ADF4118
680pF
SERIAL
DIGITAL
INTERFACE
100pF
18Ω
6.8nF
18Ω
RF
B
RF A
IN
IN
100pF
100pF
51Ω
POWER SUPPLY CONNECTIONS AND DECOUPLING CAPACITORS
ARE OMITTED FROM DIAGRAM FOR CLARITY.
Figure 37. Direct Conversion Transmitter Solution
Rev. D | Page 23 of 28
ADF4116/ADF4117/ADF4118
On first applying power to the ADF411x family, it requires three
writes (one each to the R counter latch, the N counter latch, and
the initialization latch) for the output to become active.
INTERFACING
The ADF411x family has a simple SPI®-compatible serial inter-
face for writing to the device. CLK, DATA, and LE control the
data transfer. When LE (latch enable) goes high, the 24 bits that
are clocked into the input register on each rising edge of CLK
are transferred to the appropriate latch. See Figure 2 for the
timing diagram and Table 5 for the latch truth table.
I/O port lines on the ADuC812 are also used to control power-
down (CE input) and to detect lock (MUXOUT configured as
lock detect and polled by the port input).
When operating in the mode described, the maximum SCLOCK
rate of the ADuC812 is 4 MHz. This means that the maximum
rate at which the output frequency can be changed is 166 kHz.
The maximum allowable serial clock rate is 20 MHz. This means
that the maximum update rate possible for the device is 833 kHz
or one update every 1.2 μs. This is more than adequate for
systems that have typical lock times in hundreds of microseconds.
ADSP-21xx Interface
Figure 39 shows the interface between the ADF411x family and
the ADSP-21xx digital signal processor. The ADF411x family
needs a 21-bit serial word for each latch write. The easiest way
to accomplish this using the ADSP-21xx family is to use the
autobuffered transmit mode of operation with alternate framing.
This provides a means for transmitting an entire block of serial
data before an interrupt is generated.
ADuC812 Interface
Figure 38 shows the interface between the ADF411x family and
the ADuC812 MicroConverter®. Since the ADuC812 is based
on an 8051 core, this interface can be used with any 8051-based
microcontroller. The MicroConverter is set up for SPI master
mode with CPHA = 0. To initiate the operation, the I/O port
driving LE is brought low. Each latch of the ADF411x family
needs a 24-bit word. This is accomplished by writing three 8-bit
bytes from the MicroConverter to the device. When the third
byte has been written, the LE input should be brought high to
complete the transfer.
CLK
SCLK
DT
DATA
ADSP-21xx
ADF4116/
ADF4117/
ADF4118
TFS
LE
CE
I/O FLAGS
CLK
DATA
LE
SCLOCK
MOSI
MUXOUT
(LOCK DETECT)
ADuC812
ADF4116/
ADF4117/
ADF4118
Figure 39. ADSP-21xx to ADF411x family Interface
I/O PORTS
Set up the word length for 8 bits and use three memory
locations for each 24-bit word. To program each 21-bit latch,
store the three 8-bit bytes, enable the autobuffered mode, and
write to the transmit register of the DSP. This last operation
initiates the autobuffer transfer.
CE
MUXOUT
(LOCK DETECT)
Figure 38. ADuC812 to ADF411x family Interface
Rev. D | Page 24 of 28
ADF4116/ADF4117/ADF4118
OUTLINE DIMENSIONS
5.10
5.00
4.90
16
9
8
4.50
4.40
4.30
6.40
BSC
1
PIN 1
1.20
MAX
0.15
0.05
0.20
0.09
0.75
0.60
0.45
8°
0°
0.30
0.19
0.65
BSC
SEATING
PLANE
COPLANARITY
0.10
COMPLIANT TO JEDEC STANDARDS MO-153AB
Figure 40. 16-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-16)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADF4116BRU
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
Package Option
RU-16
16-Lead Thin Shrink Small Outline Package (TSSOP)
16-Lead Thin Shrink Small Outline Package (TSSOP)
16-Lead Thin Shrink Small Outline Package (TSSOP)
16-Lead Thin Shrink Small Outline Package (TSSOP)
16-Lead Thin Shrink Small Outline Package (TSSOP)
16-Lead Thin Shrink Small Outline Package (TSSOP)
16-Lead Thin Shrink Small Outline Package (TSSOP)
16-Lead Thin Shrink Small Outline Package (TSSOP)
16-Lead Thin Shrink Small Outline Package (TSSOP)
16-Lead Thin Shrink Small Outline Package (TSSOP)
16-Lead Thin Shrink Small Outline Package (TSSOP)
16-Lead Thin Shrink Small Outline Package (TSSOP)
ADF4116BRU-REEL
ADF4116BRU-REEL7
ADF4116BRUZ1
ADF4116BRUZ-REEL1
ADF4116BRUZ-REEL71
RU-16
RU-16
RU-16
RU-16
RU-16
ADF4117BRU
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
ADF4117BRU-REEL
ADF4117BRU-REEL7
ADF4117BRUZ1
ADF4117BRUZ-RL1
ADF4117BRUZ-RL71
ADF4118BRU
16-Lead Thin Shrink Small Outline Package (TSSOP)
16-Lead Thin Shrink Small Outline Package (TSSOP)
16-Lead Thin Shrink Small Outline Package (TSSOP)
16-Lead Thin Shrink Small Outline Package (TSSOP)
16-Lead Thin Shrink Small Outline Package (TSSOP)
16-Lead Thin Shrink Small Outline Package (TSSOP)
16-Lead Thin Shrink Small Outline Package (TSSOP)
16-Lead Thin Shrink Small Outline Package (TSSOP)
16-Lead Thin Shrink Small Outline Package (TSSOP)
Evaluation Board
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
ADF4118BRU-REEL
ADF4118BRU-REEL7
ADF4118BRUZ1
ADF4118BRUZ-RL1
ADF4118BRUZ-RL71
ADF4118YRUZ1
ADF4118YRUZ-RL1
ADF4118YRUZ-RL71
EVAL-ADF4118EBZ11
EVAL-ADF411XEBZ11
Evaluation Board
1 Z = RoHS Compliant Part.
Rev. D | Page 25 of 28
ADF4116/ADF4117/ADF4118
NOTES
Rev. D | Page 26 of 28
ADF4116/ADF4117/ADF4118
NOTES
Rev. D | Page 27 of 28
ADF4116/ADF4117/ADF4118
NOTES
Purchase of licensed I2C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips I2C Patent
Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips.
© 2000–2007 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D00392-0-4/07(D)
Rev. D | Page 28 of 28
相关型号:
ADF4117BCPZ
IC PLL FREQUENCY SYNTHESIZER, 1200 MHz, CQCC20, CSP-20, PLL or Frequency Synthesis Circuit
ADI
©2020 ICPDF网 联系我们和版权申明