ADV3003ACPZ-R7 [ADI]
HDMI/DVI TMDS Equalizer; HDMI / DVI TMDS均衡器
| 型号： | ADV3003ACPZ-R7 |
| 厂家： | 
ADI |
| 描述： | HDMI/DVI TMDS Equalizer |
| 文件： | 总16页 (文件大小：773K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
HDMI/DVI TMDS Equalizer
ADV3003
FEATURES
FUNCTIONAL BLOCK DIAGRAM
PE_EN TX_EN
One input, one output HDMI/DVI high speed signal
equalizer/driver
PARALLEL
CONTROL
AVCC
ADV3003
Enables HDMI 1.3 receive-compliant input
Four TMDS channels per input/output
Supports 250 Mbps to 2.25 Gbps data rates
Supports 25 MHz to 225 MHz pixel clocks
Fully buffered unidirectional inputs/outputs
Equalized inputs for operation with long HDMI cables
(20 meters at 2.25 Gbps)
AVEE
VTTI
CONTROL
LOGIC
VTTO
+
–
4
4
4
4
+
–
IP[3:0]
IN[3:0]
OP[3:0]
ON[3:0]
BUFFER
EQ
PE
HIGH SPEED BUFFERED
Pre-emphasized outputs
Figure 1.
Matched 50 Ω input and output on-chip terminations
Low added jitter
Transmitter disable feature
Reduces power dissipation
TYPICAL APPLICATION DIAGRAM
HDTV SET
MEDIA CENTER
SET-TOP BOX
DVD PLAYER
Disables input terminations
Single-supply operation (3.3 V)
Standards compliant: HDMI receiver, DVI
40-lead, 6 mm × 6 mm, RoHS-compliant LFCSP
HDMI
RECEIVER
GAME
CONSOLE
4:1 HDMI
SWITCH
ADV3003
APPLICATIONS
Multiple input displays
Advanced television set (HDTV) front panel connectors
HDMI/DVI cable extenders
BACK PANEL
CONNECTORS
FRONT PANEL
CONNECTOR
Figure 2.
GENERAL DESCRIPTION
PRODUCT HIGHLIGHTS
The ADV3003 is a 4-channel transition minimized differential
signaling (TMDS) buffer featuring equalized inputs and
pre-emphasized outputs. The ADV3003 features 50 Ω input
and output terminations, providing full-swing output signal
recovery and minimizing reflections for improved system
signal integrity. The ADV3003 is targeted at HDMI™/DVI
applications and is ideal for use in systems with long cable
runs, long PCB traces, and designs with interior cabling.
1. Supports data rates up to 2.25 Gbps, enabling 1080p deep
color (12-bit color) HDMI formats and greater than UXGA
(1600 × 1200) DVI resolutions.
2. The 12 dB input cable equalizer enables the use of long
cables at the input. For a typical 24 AWG cable, the
ADV3003 compensates for more than 20 meters at data
rates up to 2.25 Gbps.
3. The selectable 6 dB of output pre-emphasis allows the
ADV3003 to drive high loss output cables or long PCB traces.
4. Matched 50 Ω on-chip input and output terminations
improve system signal integrity.
5. An external control pin, PE_EN, sets the output
pre-emphasis to either 0 dB or 6 dB.
The ADV3003 is provided in a 40-lead, LFCSP, surface-mount,
RoHS-compliant, plastic package and is specified to operate
over the −40°C to +85°C temperature range.
6. An external control pin, TX_EN, simultaneously disables
both the transmitter and the on-chip input terminations.
This feature reduces the power dissipation of the ADV3003
and indicates to a connected source when the ADV3003 is
disabled.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2008 Analog Devices, Inc. All rights reserved.
ADV3003
TABLE OF CONTENTS
Features .............................................................................................. 1
Typical Performance Characteristics ..............................................6
Theory of Operation ...................................................................... 10
Introduction................................................................................ 10
Input Channels ........................................................................... 10
Output Channels ........................................................................ 10
Application Notes........................................................................... 12
Pinout........................................................................................... 12
Cable Lengths and Equalization............................................... 12
Pre-Emphasis .............................................................................. 12
PCB Layout Guidelines.............................................................. 12
Outline Dimensions....................................................................... 15
Ordering Guide .......................................................................... 15
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
Typical Application Diagram.......................................................... 1
General Description......................................................................... 1
Product Highlights ........................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Absolute Maximum Ratings............................................................ 4
Thermal Resistance ...................................................................... 4
Maximum Power Dissipation ..................................................... 4
ESD Caution.................................................................................. 4
Pin Configuration and Function Descriptions............................. 5
REVISION HISTORY
2/08—Revision 0: Initial Version
Rev. 0 | Page 2 of 16
ADV3003
SPECIFICATIONS
TA = 27°C, AVCC = 3.3 V, VTTI = 3.3 V, VTTO = 3.3 V, AVEE = 0 V, differential input swing = 1000 mV, pattern = PRBS 27 − 1,
data rate = 2.25 Gbps, TMDS outputs terminated with external 50 Ω resistors to 3.3 V, unless otherwise noted.
Table 1.
Parameter
Conditions/Comments
Min
Typ
Max
Unit
DYNAMIC PERFORMANCE
Maximum Data Rate (DR) per Channel
Bit Error Rate (BER)
Added Deterministic Jitter
Added Random Jitter
Differential Intrapair Skew
Differential Interpair Skew1
EQUALIZATION PERFORMANCE
Receiver (Fixed Setting)2
Transmitter (Pre-Emphasis On)3
INPUT CHARACTERISTICS
Input Voltage Swing
NRZ
2.25
Gbps
PRBS 223 − 1
10−9
DR ≤ 2.25 Gbps, PRBS 27 − 1
25
1
1
ps (p-p)
ps (rms)
ps
At output
At output
50
ps
Boost frequency = 1.125 GHz
Boost frequency = 1.125 GHz
12
6
dB
dB
Differential
150
AVCC − 800
1200
AVCC
mV
mV
Input Common-Mode Voltage (VICM
OUTPUT CHARACTERISTICS4
High Voltage Level
)
Single-ended high speed channel
Single-ended high speed channel
AVCC − 200
AVCC − 600
75
AVCC + 10
mV
Low Voltage Level
Rise/Fall Time (20% to 80%)
AVCC − 400 mV
178
ps
TERMINATION
Input Termination Resistance
Output Termination Resistance
POWER SUPPLY
Single-ended
Single-ended
50
50
Ω
Ω
AVCC
Operating range (3.3 V 10%)
3
3.3
3.6
V
QUIESCENT CURRENT
AVCC
Output disabled
20
32
66
40
40
80
0
40
50
80
54
50
100
1
mA
mA
mA
mA
mA
mA
mA
Output enabled, pre-emphasis off
Output enabled, pre-emphasis on
Input termination on5
Output termination on, pre-emphasis off
Output termination on, pre-emphasis on
Output disabled
VTTI
VTTO
POWER DISSIPATION6
Output disabled
66
370
686
148
553
937
mW
mW
mW
Output enabled, pre-emphasis off
Output enabled, pre-emphasis on
TX_EN, PE_EN
PARALLEL CONTROL INTERFACE
Input High Voltage, VIH
Input Low Voltage, VIL
2
V
V
0.8
1 Differential interpair skew is measured between the TMDS pairs of the HDMI/DVI link.
2 ADV3003 output meets the transmitter eye diagram mask as defined in the HDMI Standard Version 1.3a and the DVI Standard Version 1.0.
3 Cable output meets the receiver eye diagram mask as defined in the HDMI Standard Version 1.3a and the DVI Standard Version 1.0.
4 PE = 0 dB.
5 Typical value assumes the HDMI/DVI link is active with nominal signal swings. Minimum and maximum limits are measured at the extremes of input termination
resistance and input voltage swing, respectively .
6 The total power dissipation excludes power dissipated in the 50 Ω off-chip loads.
Rev. 0 | Page 3 of 16
ADV3003
ABSOLUTE MAXIMUM RATINGS
Table 2.
THERMAL RESISTANCE
θJA is specified for the worst-case conditions, that is, a device
soldered in a 4-layer JEDEC circuit board for surface-mount
packages. JC is specified for the exposed pad soldered to the
circuit board with no airflow.
Parameter
Rating
AVCC to AVEE
VTTI
VTTO
Internal Power Dissipation
High Speed Input Voltage
3.7 V
AVCC + 0.6 V
AVCC + 0.6 V
2.0 W
AVCC − 1.4 V < VIN
AVCC + 0.6 V
2.0 V
AVEE − 0.3 V < VIN
AVCC + 0.6 V
Table 3.
<
Package Type
θJA
θJC
Unit
40-Lead LFCSP
31.9
2.6
°C/W
High Speed Differential Input Voltage
Parallel Interface (TX_EN, PE_EN)
<
MAXIMUM POWER DISSIPATION
StorageTemperature Range
Operating Temperature Range
Junction Temperature
−65°C to +125°C
−40°C to +85°C
150°C
The maximum power that can be safely dissipated by the ADV3003
is limited by the associated rise in junction temperature. The
maximum safe junction temperature for plastic encapsulated
devices is determined by the glass transition temperature of the
plastic, approximately 150°C. Temporarily exceeding this limit
may cause a shift in parametric performance due to a change
in the stresses exerted on the die by the package. Exceeding a
junction temperature of 175°C for an extended period can result
in device failure. To ensure proper operation, it is necessary to
observe the maximum power derating as determined by the
thermal resistance coefficients.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
Rev. 0 | Page 4 of 16
ADV3003
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
PIN 1
INDICATOR
IN0
IP0
1
2
3
4
5
6
7
8
9
30 AVCC
29 PE_EN
28 TX_EN
27 AVEE
26 AVCC
25 AVCC
24 AVEE
23 AVCC
22 AVCC
21 NC
IN1
IP1
ADV3003
VTTI
IN2
IP2
TOP VIEW
(Not to Scale)
IN3
IP3
AVCC 10
NOTES
1. NC = NO CONNECT.
2. THE ADV3003 LFCSP HAS AN EXPOSED PADDLE (ePAD) ON THE UNDERSIDE
OF THE PACKAGE, WHICH AIDS IN HEAT DISSIPATION. THE ePAD MUST BE
ELECTRICALLY CONNECTED TO THE AVEE SUPPLY PLANE TO MEET
ELECTRICAL AND THERMAL SPECIFICATIONS.
Figure 3. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
Mnemonic
IN0
Type1
HS, I
Description
1
High Speed Input Complement.
High Speed Input.
2
IP0
HS, I
3
IN1
HS, I
High Speed Input Complement.
High Speed Input.
4
IP1
HS, I
5
VTTI
IN2
Power
HS, I
Input Termination Supply. Nominally connected to AVCC.
High Speed Input Complement.
High Speed Input.
6
7
IP2
HS, I
8
IN3
HS, I
High Speed Input Complement.
High Speed Input.
9
IP3
HS, I
10, 16, 22, 23, 25, 26, 30, 32
AVCC
ON0
OP0
VTTO
ON1
OP1
ON2
OP2
ON3
OP3
AVEE
TX_EN
PE_EN
NC
Power
HS, O
HS, O
Power
HS, O
HS, O
HS, O
HS, O
HS, O
HS, O
Power
Control
Control
NC
Positive Analog Supply. 3.3 V nominal.
High Speed Output Complement.
High Speed Output.
11
12
13
Output Termination Supply. Nominally connected to AVCC.
High Speed Output Complement.
High Speed Output.
14
15
17
High Speed Output Complement.
High Speed Output.
18
19
High Speed Output Complement.
High Speed Output.
20
24, 27, 37, ePAD
Negative Analog Supply. 0 V nominal.
High Speed Output Enable Parallel Interface.
High Speed Pre-Emphasis Enable Parallel Interface.
No Connect.
28
29
21, 31, 33, 34, 35, 36, 38, 39, 40
1 HS = high speed, I = input, O = output.
Rev. 0 | Page 5 of 16
ADV3003
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 27°C, AVCC = 3.3 V, VTTI = 3.3 V, VTTO = 3.3 V, AVEE = 0 V, differential input swing = 1000 mV, pattern = PRBS 27 − 1,
data rate = 2.25 Gbps, TMDS outputs terminated with external 50 Ω resistors to 3.3 V, unless otherwise noted.
HDMI CABLE
ADV3003
DIGITAL
PATTERN
GENERATOR
SERIAL DATA
ANALYZER
EVALUATION
BOARD
SMA COAX CABLE
REFERENCE EYE DIAGRAM AT TP1
TP1
TP2
TP3
Figure 4. Test Circuit Diagram for Rx Eye Diagrams
0.125UI/DIV AT 2.25Gbps
0.125UI/DIV AT 2.25Gbps
Figure 5. Rx Eye Diagram at TP2 (Cable = 2 Meters, 24 AWG)
Figure 7. Rx Eye Diagram at TP3, EQ = 12 dB (Cable = 2 Meters, 24 AWG)
0.125UI/DIV AT 2.25Gbps
0.125UI/DIV AT 2.25Gbps
Figure 6. Rx Eye Diagram at TP2 (Cable = 20 Meters, 24 AWG)
Figure 8. Rx Eye Diagram at TP3, EQ = 12 dB (Cable = 20 Meters, 24 AWG)
Rev. 0 | Page 6 of 16
ADV3003
TA = 27°C, AVCC = 3.3 V, VTTI = 3.3 V, VTTO = 3.3 V, AVEE = 0 V, differential input swing = 1000 mV, pattern = PRBS 27 − 1,
data rate = 2.25 Gbps, TMDS outputs terminated with external 50 Ω resistors to 3.3 V, unless otherwise noted.
HDMI CABLE
ADV3003
SERIAL DATA
ANALYZER
DIGITAL
PATTERN
GENERATOR
EVALUATION
BOARD
SMA COAX CABLE
REFERENCE EYE DIAGRAM AT TP1
TP1
TP2
TP3
Figure 9. Test Circuit Diagram for Tx Eye Diagrams
0.125UI/DIV AT 2.25Gbps
0.125UI/DIV AT 2.25Gbps
Figure 10. Tx Eye Diagram at TP2, PE = 0 dB
Figure 12. Tx Eye Diagram at TP3, PE = 0 dB (Cable = 6 Meters, 24 AWG)
0.125UI/DIV AT 2.25Gbps
0.125UI/DIV AT 2.25Gbps
Figure 11. Tx Eye Diagram at TP2, PE = 6 dB
Figure 13. Tx Eye Diagram at TP3, PE = 6 dB (Cable = 10 Meters, 24 AWG)
Rev. 0 | Page 7 of 16
ADV3003
TA = 27°C, AVCC = 3.3 V, VTTI = 3.3 V, VTTO = 3.3 V, AVEE = 0 V, differential input swing = 1000 mV, pattern = PRBS 27 − 1,
data rate = 2.25 Gbps, TMDS outputs terminated with external 50 Ω resistors to 3.3 V, unless otherwise noted.
0.6
0.5
0.4
0.3
0.2
0.1
0
0.6
0.5
0.4
0.3
0.2
0.1
0
ALL CABLES = 24 AWG
PE = 6dB
ALL CABLES = 24 AWG
1080p, 12-BIT
1.65Gbps
1080p, 12-BIT
1080p, 8-BIT
1080p, 8-BIT
720p/1080i,
8-BIT
1.65Gbps
720p/1080i,
8-BIT
480p, 8-BIT
480p, 8-BIT
0
5
10
15
20
25
0
2
4
6
8
10
12
14
16
INPUT CABLE LENGTH (m)
OUTPUT CABLE LENGTH (m)
Figure 14. Jitter vs. Input Cable Length (See Figure 4 for Test Setup)
Figure 17. Jitter vs. Output Cable Length (See Figure 9 for Test Setup)
50
1.2
1.0
0.8
0.6
0.4
0.2
0
1080p, 12-BIT
40
1080p, 8-BIT
30
720p/1080i,
8-BIT
20
DJ p-p
10
RJ rms
0
0
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4
DATA RATE (Gbps)
0
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4
DATA RATE (Gbps)
Figure 15. Jitter vs. Data Rate
Figure 18. Eye Height vs. Data Rate
50
40
30
20
10
0
1.2
1.0
0.8
0.6
0.4
0.2
0
DJ p-p
RJ rms
3.0
3.1
3.2
3.3
3.4
3.5
3.6
3.0
3.1
3.2
3.3
3.4
3.5
3.6
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
Figure 16. Jitter vs. Supply Voltage
Figure 19. Eye Height vs. Supply Voltage
Rev. 0 | Page 8 of 16
ADV3003
TA = 27°C, AVCC = 3.3 V, VTTI = 3.3 V, VTTO = 3.3 V, AVEE = 0 V, differential input swing = 1000 mV, pattern = PRBS 27 − 1,
data rate = 2.25 Gbps, TMDS outputs terminated with external 50 Ω resistors to 3.3 V, unless otherwise noted.
80
70
60
50
40
30
20
10
0
50
45
40
35
30
25
20
15
10
5
DJ p-p
DJ p-p
RJ rms
RJ rms
0
0
0.5
1.0
1.5
2.0
2.5
2.7
2.9
3.1
3.3
3.5
3.7
DIFFERENTIAL INPUT VOLTAGE SWING (V)
INPUT COMMON-MODE VOLTAGE (V)
Figure 20. Jitter vs. Differential Input Voltage Swing
Figure 23. Jitter vs. Input Common-Mode Voltage
50
40
30
20
10
0
120
115
110
105
100
95
DJ p-p
90
85
RJ rms
80
–40
–15
10
35
60
85
–40
–20
0
20
40
60
80
100
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 21. Jitter vs. Temperature
Figure 24. Differential Input Resistance vs. Temperature
160
140
120
100
80
RISE
FALL
60
40
20
0
–40
–20
0
20
40
60
80
100
TEMPERATURE (°C)
Figure 22. Rise and Fall Time vs. Temperature
Rev. 0 | Page 9 of 16
ADV3003
THEORY OF OPERATION
The input equalizer provides 12 dB of high frequency boost.
No specific cable length is suggested for this equalization level
because cable performance varies widely among manufacturers;
however, in general, the ADV3003 does not degrade input
signals, even for short input cables. The ADV3003 can equalize
more than 20 meters of a 24 AWG cable at 2.25 Gbps, for
reference cables that exhibit an insertion loss of −15 dB at the
fundamental frequency of this data rate.
INTRODUCTION
The primary function of the ADV3003 is to buffer the four high
speed channels of a single HDMI or DVI link. The HDMI/DVI
link consists of four differential, high speed channels and four
auxiliary single-ended, low speed control signals. The high
speed channels include a data-word clock and three transition
minimized differential signaling (TMDS) data channels
running at 10× the data-word clock frequency for data rates
up to 2.25 Gbps.
OUTPUT CHANNELS
All four high speed TMDS channels on the ADV3003 are
identical; that is, the pixel clock can be run on any of the four
TMDS channels. Receive channel compensation (12 dB of
fixed equalization) is provided for the high speed channels
to support long input cables. The ADV3003 also includes
selectable pre-emphasis for driving high loss output cables
or long PCB traces.
Each high speed output differential pair of the ADV3003
terminates to the 3.3 V VTTO power supply through two
single-ended 50 Ω on-chip resistors, as shown in Figure 26.
VTTO
50Ω
50Ω
OP[3:0]
ON[3:0]
TX_EN
In the intended application, the ADV3003 is placed between
a source and a sink, with long cable runs at both the input and
the output.
INPUT CHANNELS
I
OUT
Each high speed input differential pair terminates to the
3.3 V VTTI power supply through a pair of single-ended 50 Ω
on-chip resistors, as shown in Figure 25. When the transmitter
of the ADV3003 is disabled by setting the TX_EN control pin
as shown in Table 5, the input termination resistors are also
disabled to provide a high impedance node at the inputs. Disabl-
ing the input terminations when the transmitter is disabled
indicates to any connected HDMI sources that the link through
the ADV3003 is inactive.
AVEE
Figure 26. High Speed Output Simplified Schematic
The output termination resistors of the ADV3003 back-terminate
the output TMDS transmission lines. These back-terminations,
as recommended in the HDMI 1.3 specification, act to absorb
reflections from impedance discontinuities on the output traces,
improving the signal integrity of the output traces and adding
flexibility to how the output traces can be routed. For example,
interlayer vias can be used to route the ADV3003 TMDS outputs
on multiple layers of the PCB without severely degrading the
quality of the output signal.
VTTI
50Ω
50Ω
TX_EN
IP[3:0]
IN[3:0]
CABLE
EQ
AVEE
Figure 25. High Speed Input Simplified Schematic
Rev. 0 | Page 10 of 16
ADV3003
The ADV3003 has an external control pin, TX_EN. The
TX_EN pin must be connected to either a logic high (1) or
low (0), in accordance with the logic values set forth in Table 1.
The use of the TX_EN pin is described in Table 5. When the
transmitter is enabled by setting TX_EN to 1, both the input
and output terminations are enabled. Setting TX_EN to 0
disables the transmitter, reducing power when the transmitter
is not in use. When the transmitter is disabled, the input termi-
nation resistors are also disabled to present a high impedance
state at the input and indicate to any connected HDMI sources
that the link through the ADV3003 is inactive.
The ADV3003 also includes two levels of programmable output
pre-emphasis, 0 dB and 6 dB. The output pre-emphasis level can
be manually configured by setting the PE_EN pin. The PE_EN
pin must be connected to either a logic high (1) or low (0), in
accordance with the logic values set forth in Table 1. The use of
the PE_EN pin is described in Table 6. No specific cable length
is suggested for use with either pre-emphasis setting, because
cable performance varies widely among manufacturers.
Table 6. Pre-Emphasis Enable Setting
PE_EN
Boost
0
1
0 dB
6 dB
Table 5. Transmitter Enable Setting
Input
TX_EN Termination
Transmitter
State
Output
Termination
In a typical application, the output of the ADV3003 is
connected to the input of an HDMI/DVI receiver, which
provides a second set of matched terminations in accordance
with the HDMI 1.3 specification. If neither receiver nor receiver
termination is connected to the output of the ADV3003 in the
end-application, each ADV3003 output pin should be tied to 3.3
V through a 50 Ω resistor.
0
1
Off
On
Off
On
On
On
Rev. 0 | Page 11 of 16
ADV3003
APPLICATION NOTES
The ADV3003 is a TMDS buffer featuring equalized inputs
and pre-emphasized outputs. It is intended for use as a buffer
in HDMI/DVI systems with long input cable runs, and is fully
HDMI 1.3 receive-compliant.
PRE-EMPHASIS
The pre-emphasis of the ADV3003 acts to boost the initial
voltage swing of the output signals. Pre-emphasis provides a
distinct advantage in systems where the ADV3003 is driving
either high loss cables or long PCB traces, because the added
boost helps to ensure that the data eye at the far end of the
output cables or PCB traces meets the HDMI receive mask. The
use of pre-emphasis in a system is highly application specific.
PINOUT
The ADV3003 is designed to have an HDMI/DVI receiver
pinout at its input and a transmitter pinout at its output. This
makes the ADV3003 ideal for use in advanced TV front-panel
connectors and AVR-type applications where a designer routes
both the inputs and the outputs directly to HDMI/DVI connec-
tors—all of the high speed signals can be routed on one side of
the board.
PCB LAYOUT GUIDELINES
The ADV3003 is a 4-channel TMDS buffer, targeted for use in
HDMI and DVI video applications. Although the HDMI/DVI
link consists of four differential, high speed channels and four
single-ended, low speed auxiliary control signals, the ADV3003
buffers only the high speed signals.
The ADV3003 provides 12 dB of input equalization, so it can
compensate for the signal degradation of long input cables.
In addition, the ADV3003 can also provide up to 6 dB of
pre-emphasis that boosts the output TMDS signals and allows
the ADV3003 to precompensate when driving long PCB traces
or high loss output cables. The net effect of the input equalization
and output pre-emphasis is that the ADV3003 can compensate
for signal degradation of both the input and output cables; it
acts to reopen a closed input data eye and transmit a full-swing
HDMI signal to an end receiver.
The high speed signals carry the audiovisual (AV) data, which
is encoded by a technique called TMDS. For HDMI, the TMDS
data is further encrypted in accordance with the high bandwidth
digital content protection (HDCP) standard.
The TMDS signals are differential, unidirectional, and high
speed (up to 2.25 Gbps). The channels that carry the video data
must have a controlled impedance, be terminated at the receiver,
and be capable of operating up to at least 2.25 Gbps. It is especially
important to note that the PCB traces that carry the TMDS
signals should be designed with a controlled differential
impedance of 100 Ω. The ADV3003 provides single-ended
50 Ω terminations on chip for both its inputs and outputs.
Transmitter termination is not fully specified by the HDMI
standard, but its inclusion in the ADV3003 improves the
overall system signal integrity.
CABLE LENGTHS AND EQUALIZATION
The 12 dB equalizer of the ADV3003 is optimized for video
data rates of 2.25 Gbps and can equalize more than 20 meters
of 24 AWG HDMI cable at the input at 2.25 Gbps, the data rate
corresponding to the video format 1080p with 12-bit deep color.
The length of cable that can be used in a typical HDMI/DVI
application depends on a large number of factors including
TMDS Signals
•
Cable quality: The quality of the cable in terms of
conductor wire gauge and shielding. Thicker conductors
have lower signal degradation per unit length.
Data rate: The data rate being sent over the cable. The signal
degradation over HDMI cables increases with data rate.
Edge rates: The edge rates of the source. Slower input edges
result in more significant data eye closure at the
end of a cable.
In the HDMI/DVI standard, four differential pairs carry the
TMDS signals. In DVI, three of these pairs are dedicated to
carrying RGB video and sync data. For HDMI, audio data is
also interleaved with the video data; the DVI standard does
not incorporate audio information. The fourth high speed
differential pair is used for the AV data-word clock, which
runs at one-tenth the speed of the video data channels.
•
•
•
Receiver sensitivity: The sensitivity of the terminating
receiver.
The four high speed channels of the ADV3003 are identical.
No concession was made to lower the bandwidth of the fourth
channel for the pixel clock, so any channel can be used for any
TMDS signal; the user chooses which signal is routed over
which channel. In addition, the TMDS channels are symmetric;
therefore, the p and n of a given differential pair are inter-
changeable, provided the inversion is consistent across all
inputs and outputs of the ADV3003.
Because of these considerations, specific cable types and lengths
are not recommended for use with this equalizer. The ADV3003
equalizer does not degrade signal integrity, even for short input
cables.
Rev. 0 | Page 12 of 16
ADV3003
The ADV3003 buffers the TMDS signals; therefore, the input
traces can be considered electrically independent of the output
traces. In most applications, the quality of the signal on the input
TMDS traces is more sensitive to the PCB layout. Regardless of
the data being carried on a specific TMDS channel, or whether
the TMDS line is at the input or the output of the ADV3003, all
four high speed signals should be routed on a PCB in accordance
with the same RF layout guidelines.
Controlling the Characteristic Impedance of a TMDS
Differential Pair
The characteristic impedance of a differential pair depends on
a number of variables including the trace width, the distance
between the two traces, the height of the dielectric material
between the trace and the reference plane below it, and the
dielectric constant of the PCB binder material. To a lesser
extent, the characteristic impedance also depends upon the
trace thickness and the presence of solder mask.
Layout for the TMDS Signals
Many combinations can produce the correct characteristic imped-
ance. It is generally required to work with the PC board fabri-
cator to obtain a set of parameters to produce the desired results.
The TMDS differential pairs can either be microstrip traces,
routed on the outer layer of a board, or stripline traces, routed
on an internal layer of the board. If microstrip traces are used,
there should be a continuous reference plane on the PCB layer
directly below the traces. If stripline traces are used, they must
be sandwiched between two continuous reference planes in the
PCB stack-up. Additionally, the p and n of each differential pair
must have a controlled differential impedance of 100 Ω. The
characteristic impedance of a differential pair is a function of
several variables including the trace width, the distance separating
the two traces, the spacing between the traces and the reference
plane, and the dielectric constant of the PC board binder material.
Interlayer vias introduce impedance discontinuities that can
cause reflections and jitter on the signal path; therefore, it is
preferable to route the TMDS lines exclusively on one layer of the
board, particularly for the input traces. In addition, to prevent
unwanted signal coupling and interference, route the TMDS
signals away from other signals and noise sources on the PCB.
One consideration is how to guarantee a differential pair with a
differential impedance of 100 Ω over the entire length of the
trace. One technique to accomplish this is to change the width
of the traces in a differential pair based on how closely one trace
is coupled to the other. When the two traces of a differential
pair are close and strongly coupled, they should have a width
that produces a 100 Ω differential impedance. When the traces
split apart, for example, to go into a connector, and are no
longer so strongly coupled, the width of the traces should be
increased to yield a differential impedance of 100 Ω in the new
configuration.
Ground Current Return
In some applications, it may be necessary to invert the output
pin order of the ADV3003. This requires routing of the TMDS
traces on multiple layers of the PCB. When routing differential
pairs on multiple layers, it is also necessary to reroute the corres-
ponding reference plane to provide one continuous ground
current return path for the differential signals. Standard plated
through-hole vias are acceptable for both the TMDS traces and
the reference plane. An example of this routing is illustrated in
Figure 27. To lower the impedance between the two ground
planes, additional through-hole vias should be used to stitch the
planes together, as space allows.
Both traces of a given differential pair must be equal in length
to minimize intrapair skew. Maintaining the physical symmetry
of a differential pair is integral to ensuring its signal integrity;
excessive intrapair skew can introduce jitter through duty cycle
distortion (DCD). The p and n of a given differential pair should
always be routed together to establish the required 100 Ω
differential impedance. Enough space should be left between
the differential pairs of a given group so that the n of one pair
does not couple to the p of another pair. For example, one tech-
nique is to make the interpair distance 4× to 10× wider than the
intrapair spacing.
THROUGH-HOLE VIAS
SILKSCREEN
Any group of four TMDS channels (input or output) should
have closely matched trace lengths to minimize interpair skew.
Severe interpair skew can cause the data on the four different
channels of a group to arrive out of alignment with one another.
A good practice is to match the trace lengths for a given group
of four channels to within 0.05 inches on FR4 material.
LAYER 1: SIGNAL (MICROSTRIP)
PCB DIELECTRIC
LAYER 2: GND (REFERENCE PLANE)
PCB DIELECTRIC
LAYER 3: PWR
(REFERENCE PLANE)
The length of the TMDS traces should be minimized to
reduce overall signal degradation. Commonly used PC board
material such as FR4 is lossy at high frequencies, so long traces
on the circuit board increase signal attenuation, resulting in
decreased signal swing and increased jitter through intersymbol
interference (ISI).
PCB DIELECTRIC
LAYER 4: SIGNAL (MICROSTRIP)
SILKSCREEN
KEEP REFERENCE PLANE
ADJACENT TO SIGNAL ON ALL
LAYERS TO PROVIDE CONTINUOUS
GROUND CURRENT RETURN PATH.
Figure 27. Example Routing of Reference Plane
Rev. 0 | Page 13 of 16
ADV3003
TMDS Terminations
In a typical application, all pins labeled AVEE, including the
ePAD, should be connected directly to ground. All pins labeled
AVCC, VTTI, or VTTO should be connected to 3.3 V. The
supplies can also be powered individually, but care must be
taken to ensure that each stage of the ADV3003 is powered
correctly.
The ADV3003 provides internal 50 Ω single-ended
terminations for all its high speed inputs and outputs.
The output termination resistors are always enabled and act
to back-terminate the output TMDS transmission lines. These
back-terminations act to absorb reflections from impedance
discontinuities on the output traces, improving the signal
integrity of the output traces and adding flexibility to how the
output traces can be routed. For example, interlayer vias can be
used to route the ADV3003 TMDS outputs on multiple layers of
the PCB without severely degrading the quality of the output
signal.
Power Supply Bypassing
The ADV3003 requires minimal supply bypassing. When
powering the supplies individually, place a 0.01 μF capacitor
between each 3.3 V supply pin (AVCC, VTTI, and VTTO) and
ground to filter out supply noise. Generally, bypass capacitors
should be placed near the power pins and should connect
directly to the relevant supplies (without long intervening
traces). For example, to improve the parasitic inductance of the
power supply decoupling capacitors, minimize the trace length
between capacitor landing pads and the vias as shown in
Figure 28.
In a typical application, the ADV3003 output is connected to an
HDMI/DVI receiver or another device with a 50 Ω single-ended
input termination. It is recommended that the outputs be
terminated with external 50 Ω on-board resistors when the
ADV3003 is not connected to another device.
RECOMMENDED
Auxiliary Control Signals
There are four low-speed, single-ended control signals asso-
ciated with each source or sink in an HDMI/DVI application.
These control signals are hot plug detect (HPD), consumer
electronics control (CEC), and two display data channel (DDC)
lines. The two signals on the DDC bus are serial data and serial
clock (SDA and SCL, respectively). The ADV3003, which is a
TMDS-only part, does not buffer these low speed signals. If the
end application requires it, use other means to buffer these
signals.
EXTRA ADDED INDUCTANCE
NOT RECOMMENDED
Figure 28. Recommended Pad Outline for Bypass Capacitors
Power Supplies
In applications where the ADV3003 is powered by a single 3.3 V
supply, it is recommended to use two reference supply planes
and bypass the 3.3 V reference plane to the ground reference
plane with one 220 pF, one 1000 pF, two 0.01 μF, and one 4.7 μF
capacitors. The capacitors should via down directly to the
supply planes and be placed within a few centimeters of the
ADV3003.
The ADV3003 has three separate power supplies referenced
to a single ground, AVEE. The supply/ground pairs are as
follows: AVCC/AVEE, VTTI/AVEE, and VTTO/AVEE.
The AVCC/AVEE supply (3.3 V) powers the core of the
ADV3003. The VTTI/AVEE supply (3.3 V) powers the input
termination (see Figure 25). Similarly, the VTTO/AVEE supply
(3.3 V) powers the output termination (see Figure 26).
Rev. 0 | Page 14 of 16
ADV3003
OUTLINE DIMENSIONS
6.00
BSC SQ
0.60 MAX
0.60 MAX
PIN 1
INDICATOR
31
40
1
30
PIN 1
INDICATOR
0.50
BSC
TOP
VIEW
4.25
4.10 SQ
3.95
5.75
BSC SQ
EXPOSED
PAD
(BOT TOM VIEW)
0.50
0.40
0.30
21
10
11
20
0.25 MIN
4.50
REF
12° MAX
0.80 MAX
0.65 TYP
0.05 MAX
0.02 NOM
1.00
0.85
0.80
0.30
0.23
0.18
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-220-VJJD-2
*
THE ADV3003 HAS A CONDUCTIVE HEAT SLUG (ePAD) TO HELP DISSIPATE HEAT AND ENSURE RELIABLE OPERATION OF
THE DEVICE OVER THE FULL HDMI/DVI TEMPERATURE RANGE. THE SLUG IS EXPOSED ON THE BOTTOM OF
THE PACKAGE AND ELECTRICALLY CONNECTED TO AVEE. IT IS RECOMMENDED THAT NO PCB SIGNAL TRACES
OR VIAS BE LOCATED UNDER THE PACKAGE THAT COULD COME IN CONTACT WITH THE CONDUCTIVE SLUG.
ATTACHING THE SLUG TO AN AVEE POWER PLANE REDUCES THE JUNCTION TEMPERATURE OF THE DEVICE WHICH
MAY BE BENEFICIAL IN HIGH TEMPERATURE ENVIRONMENTS.
Figure 29. 40-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
6 mm × 6 mm Body, Very Thin Quad
(CP-40-1)
Dimensions shown in millimeters
ORDERING GUIDE
Temperature
Range
Package
Option
Ordering
Quantity
Model
Package Description
ADV3003ACPZ1
ADV3003ACPZ-R71
ADV3003-EVALZ1
−40°C to +85°C
−40°C to +85°C
40-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
40-Lead Lead Frame Chip Scale Package [LFCSP_VQ], Reel 7
Evaluation Board
CP-40-1
CP-40-1
490
1500
1 Z = RoHS Compliant Part.
Rev. 0 | Page 15 of 16
ADV3003
NOTES
©2008 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D07212-0-2/08(0)
Rev. 0 | Page 16 of 16
相关型号：
©2020 ICPDF网 联系我们和版权申明