ADW71205WSTZ-RL [ADI]
12-Bit R/D Converter with Reference Oscillator;型号: | ADW71205WSTZ-RL |
厂家: | ADI |
描述: | 12-Bit R/D Converter with Reference Oscillator 转换器 |
文件: | 总20页 (文件大小:360K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
12-Bit R/D Converter
with Reference Oscillator
AD2S1205
FUNCTIONAL BLOCK DIAGRAM
FEATURES
REFERENCE
CRYSTAL
Complete monolithic resolver-to-digital converter (RDC)
Parallel and serial 12-bit data ports
System fault detection
PINS
AD2S1205
INTERNAL
CLOCK
GENERATOR
REFERENCE
OSCILLATOR
(DAC)
VOLTAGE
REFERENCE
EXCITATION
OUTPUTS
11 arc minutes of accuracy
Input signal range: 3.15 V p-p 27ꢀ
Absolute position and velocity outputs
1250 rps maximum tracking rate, 12-bit resolution
Incremental encoder emulation (1024 pulses/rev)
Programmable sinusoidal oscillator on board
Single-supply operation (5.00 V 5ꢀ)
−40°C to +125°C temperature rating
44-lead LQFP
SYNTHETIC
REFERENCE
INPUTS
FROM
FAULT
DETECTION
OUTPUTS
ADC
ADC
FAULT
TYPE II TRACKING LOOP
POSITION REGISTER
DETECTION
RESOLVER
VELOCITY REGISTER
ENCODER
EMULATION
OUTPUTS
ENCODER
EMULATION
MULTIPLEXER
4 kV ESD protection
DATA BUS OUTPUT
APPLICATIONS
Automotive motion sensing and control
Hybrid-electric vehicles
DATA I/O
RESET
Figure 1.
Electric power steering
Integrated starter generator/alternator
Industrial motor control
Process control
GENERAL DESCRIPTION
PRODUCT HIGHLIGHTS
The AD2S1205 is a complete 12-bit resolution tracking
resolver-to-digital converter that contains an on-board
programmable sinusoidal oscillator providing sine wave
excitation for resolvers.
1. Ratiometric Tracking Conversion. The Type II tracking
loop provides continuous output position data without
conversion delay. It also provides noise immunity and
tolerance of harmonic distortion on the reference and
input signals.
The converter accepts 3.15 V p-p 2ꢀ7 input signals on the Sin
and Cos inputs. A Type II tracking loop is employed to track the
inputs and convert the input Sin and Cos information into a digital
representation of the input angle and velocity. The maximum
tracking rate is a function of the external clock frequency. The
performance of the AD2S105 is specified across a frequency
range of 8.192 MHz 257, allowing a maximum tracking rate
of 1250 rps.
2. System Fault Detection. A fault detection circuit can sense
loss of resolver signals, out-of-range input signals, input
signal mismatch, or loss of position tracking.
3. Input Signal Range. The Sin and Cos inputs can accept
differential input voltages of 3.15 V p-p 2ꢀ7.
4. Programmable Excitation Frequency. Excitation frequency
is easily programmable to 10 kHz, 12 kHz, 15 kHz, or 20 kHz
by using the frequency select pins (the FS1 and FS2 pins).
5. Triple Format Position Data. Absolute 12-bit angular position
data is accessed via either a 12-bit parallel port or a 3-wire
serial interface. Incremental encoder emulation is in standard
A-quad-B format with direction output available.
6. Digital Velocity Output. 12-bit signed digital velocity accessed
via either a 12-bit parallel port or a 3-wire serial interface.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2007 Analog Devices, Inc. All rights reserved.
AD2S1205
TABLE OF CONTENTS
Features .............................................................................................. 1
False Null Condition.................................................................. 10
On-Board Programmable Sinusoidal Oscillator.................... 10
Synthetic Reference Generation............................................... 11
Charge-Pump Output................................................................ 11
Connecting the Converter ........................................................ 11
Clock Requirements................................................................... 12
Absolute Position and Velocity Output................................... 12
Parallel Interface......................................................................... 12
Serial Interface............................................................................ 14
Incremental Encoder Outputs.................................................. 16
Supply Sequencing and Reset ................................................... 16
Circuit Dynamics ........................................................................... 1ꢀ
Loop Response Model ............................................................... 1ꢀ
Sources of Error.......................................................................... 18
Connecting to the DSP.............................................................. 19
Outline Dimensions....................................................................... 20
Ordering Guide .......................................................................... 20
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description......................................................................... 1
Product Highlights ........................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Absolute Maximum Ratings............................................................ 5
ESD Caution.................................................................................. 5
Pin Configuration and Function Descriptions............................. 6
Resolver Format Signals................................................................... 8
Theory of Operation ........................................................................ 9
Fault Detection Circuit ................................................................ 9
Monitor Signal .............................................................................. 9
Loss of Signal Detection .............................................................. 9
Signal Degradation Detection .................................................... 9
Loss of Position Tracking Detection........................................ 10
Responding to a Fault Condition ............................................. 10
REVISION HISTORY
1/07—Revision 0: Initial Version
Rev. 0 | Page 2 of 20
AD2S1205
SPECIFICATIONS
AVDD = DVDD = 5.0 V 57 at −40°C to +125°C, CLKIN = 8.192 MHz 257, unless otherwise noted.
Table 1.
Parameter
Sin, Cos INPUTS1
Voltage
Min
Typ
Max Unit
Conditions/Comments
2.3
3.15
4.0
12
V p-p
Sinusoidal waveforms, Sin − SinLO and Cos − CosLO,
differential inputs
VIN = 3.25 VDC, CLKIN = 10.24 MHz
VIN = 3.25 VDC
CMV with respect to REFOUT/2 at 10 kHz
Sin/Cos vs. EXC output
Input Bias Current
Input Impedance
Common-Mode Voltage
Phase-Lock Range
ANGULAR ACCURACY
Angular Accuracy
μA
0.35
−44
MΩ
100
+44
mV peak
Degrees
11
22
Arc minutes Zero acceleration, Y grade
Arc minutes Zero acceleration, W grade
Resolution
Linearity INL
Linearity DNL
Repeatability
Hysteresis
12
1
Bits
LSB
LSB
LSB
LSB
Guaranteed no missing codes
Zero acceleration, 0 rps to 1250 rps, CLKIN = 10.24 MHz
Guaranteed monotonic
2
0.3
1
VELOCITY OUTPUT
Velocity Accuracy
Resolution
Linearity
Offset
Dynamic Ripple
DYNAMIC PERFORMANCE
Bandwidth
2
1
LSB
Bits
LSB
LSB
LSB
Zero acceleration
11
1
0
Guaranteed by design, 2 LSB maximum
Zero acceleration
Zero acceleration
1
1000
2400 Hz
750 rps
1000 rps
1250 rps
Tracking Rate
CLKIN = 6.144 MHz , guaranteed by design
CLKIN = 8.192 MHz , guaranteed by design
CLKIN = 10.24 MHz , guaranteed by design
Acceleration Error
30
Arc minutes At 10,000 rps, CLKIN = 8.192 MHz
Settling Time 179° Step Input
5.2
4.0
ms
ms
To within 11 arc minutes, Y grade, CLKIN = 10.24 MHz
To within 1 degree, Y grade, CLKIN = 10.24 MHz
EXC, EXC OUTPUTS
Voltage
Center Voltage
Frequency
3.34
2.39
3.6
2.47
10
12
15
3.83
2.52
V p-p
V
Load 100 μA
kHz
kHz
kHz
kHz
mV
dB
FS1 = high, FS2 = high, CLKIN = 8.192 MHz
FS1 = high, FS2 = low, CLKIN = 8.192 MHz
FS1 = low, FS2 = high, CLKIN = 8.192 MHz
FS1 = low, FS2 = low, CLKIN = 8.192 MHz
20
EXC/EXC DC Mismatch
THD
35
−58
2.24
First five harmonics
FAULT DETECTION BLOCK
Loss of Signal (LOS)
Sin/Cos Threshold
2.18
2.3
57
V p-p
Degrees
DOS and LOT go low when Sin or Cos fall below threshold
LOS indicated before angular output error exceeds limit
(4.0 V p-p input signal and 2.18 V LOS threshold)
Angular Accuracy (Worst Case)
Angular Latency (Worst Case)
Time Latency
114
125
Degrees
μs
Maximum electrical rotation before LOS is indicated
(4.0 V p-p input signal and 2.18 V LOS threshold)
Rev. 0 | Page 3 of 20
AD2S1205
Parameter
Min
Typ
Max Unit
Conditions/Comments
Degradation of Signal (DOS)
Sin/Cos Threshold
Angular Accuracy (Worst Case)
Angular Latency (Worst Case)
Time Latency
4.0
4.09
4.2
33
66
125
420
V p-p
Degrees
Degrees
μs
DOS goes low when Sin or Cos exceeds threshold
DOS indicated before angular output error exceeds limit
Maximum electrical rotation before DOS is indicated
Sin/Cos Mismatch
385
5
mV
DOS latched low when Sin/Cos amplitude mismatch
exceeds threshold
Loss of Tracking (LOT)
Tracking Threshold
Degrees
LOT goes low when internal error signal exceeds
threshold; guaranteed by design
Time Latency
Hysteresis
1.1
ms
Degrees
4
Guaranteed by design
IOUT = 100 μA
VOLTAGE REFERENCE
REFOUT
Drift
2.39
2.47
70
−60
2.52
V
ppm/°C
dB
PSRR
CHARGE-PUMP OUTPUT (CPO)
Frequency
Duty Cycle
204.8
50
kHz
%
Square wave output, CLKIN = 8.192 MHz
POWER SUPPLY
IDD Dynamic
20
mA
ELECTRICAL CHARACTERISTICS
VIL, Voltage Input Low
VIH, Voltage Input High
VOL, Voltage Output Low
VOH, Voltage Output High
0.8
0.4
+10
V
V
V
V
2.0
+1 mA load
−1 mA load
Pins SAMPLE, CS, RDVEL, CLKIN, SOE
4.0
−10
IIL, Low Level Input Current
(Non-Pull-Up)
μA
IIL, Low Level Input Current (Pull-Up)
IIH, High Level Input Current
IOZH, High LevelThree-State Leakage
IOZL, Low LevelThree-State Leakage
−80
−10
−10
−10
+80
+10
+10
+10
μA
μA
μA
μA
Pins RD, FS1, FS2, RESET
1 The voltages for Sin, SinLO, Cos, and CosLO relative to AGND must be between 0.2 V and AVDD
.
Rev. 0 | Page 4 of 20
AD2S1205
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to
absolute maximum ratings for extended periods may affect
device reliability.
Rating
Supply Voltage (VDD
Supply Voltage (AVDD
Input Voltage
Output Voltage Swing
Operating Temperature Range (Ambient)
Storage Temperature Range
)
−0.3 V to +7.0 V
−0.3 V to +7.0 V
−0.3 V to VDD + 0.3 V
−0.3 V to VDD + 0.3 V
−40°C to +125°C
−65°C to +150°C
)
ESD CAUTION
Rev. 0 | Page 5 of 20
AD2S1205
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
44 43 42 41 40 39 38 37 36 35 34
DV
1
2
3
4
5
6
7
8
9
33 RESET
32 FS2
31 FS1
30 LOT
29 DOS
28 DIR
DD
RD
CS
SAMPLE
RDVEL
SOE
AD2S1205
TOP VIEW
(Not to Scale)
DB11/SO
DB10/SCLK
DB9
27 NM
26
25
B
A
DB8 10
DB7 11
24 CPO
23 DGND
12 13 14 15 16 17 18 19 20 21 22
Figure 2. Pin Configuration
Table 3. Pin Function Descriptions
Pin
No.
Mnemonic Description
1, 17 DVDD
Digital Supply Voltage, 4.75 V to 5.25 V. This is the supply voltage for all digital circuitry on the AD2S1205. The AVDD and DVDD
voltages ideally should be at the same potential and must not be more than 0.3 V apart, even on a transient basis.
2
RD
Edge-Triggered Logic Input. This pin acts as a frame synchronization signal and output enable. The output buffer is
enabled when CS and RD are held low.
3
4
CS
Chip Select. Active low logic input. The device is enabled when CS is held low.
SAMPLE
Sample Result. Logic input. Data is transferred from the position and velocity integrators to the position and velocity
registers, respectively, after a high-to-low transition on the SAMPLE signal.
5
6
7
RDVEL
SOE
Read Velocity. Logic input. RDVEL input is used to select between the angular position register and the angular velocity
register. RDVEL is held high to select the angular position register and low to select the angular velocity register.
Serial Output Enable. Logic input. This pin enables either the parallel or serial interface. The serial interface is selected by
holding the SOE pin low, and the parallel interface is selected by holding the SOE pin high.
DB11/SO
Data Bit 11/Serial Data Output Bus. When the SOE pin is high, this pin acts as DB11, a three-state data output pin controlled
by CS and RD. When the SOE pin is low, this pin acts as SO, the serial data output bus controlled by CS and RD. The bits are
clocked out on the rising edge of SCLK.
8
DB10/SCLK Data Bit 10/Serial Clock. In parallel mode this pin acts as DB10, a three-state data output pin controlled by CS and RD. In
serial mode this pin acts as the serial clock input.
9 to
15
DB9 to
DB3
Data Bits 9 to 3. Three-state data output pins controlled by CS and RD.
16,
23
DGND
Digital Ground. These pins are ground reference points for digital circuitry on the AD2S1205. All digital input signals
should be referred to this DGND voltage. Both of these pins can be connected to the AGND plane of a system. The
DGND and AGND voltages should ideally be at the same potential and must not be more than 0.3 V apart, even on a
transient basis.
18
to
DB2 to
DB0
Data Bits 2 to 0. Three-state data output pins controlled by CS and RD.
20
21
22
24
XTALOUT
CLKIN
CPO
Crystal Output. To achieve the specified dynamic performance, an external crystal is recommended at the CLKIN and
XTALOUT pins. The position and velocity accuracy are guaranteed for a frequency range of 8.192 MHz 25%.
Clock Input. To achieve the specified dynamic performance, an external crystal is recommended at the CLKIN and XTALOUT
pins. The position and velocity accuracy are guaranteed for a frequency range of 8.192 MHz 25%.
Charge-Pump Output. Analog output. A 204.8 kHz square wave output with a 50% duty cycle is available at the CPO
output pin. This square wave output can be used for negative rail voltage generation or to create a VCC rail.
Rev. 0 | Page 6 of 20
AD2S1205
Pin
No.
Mnemonic Description
25
26
27
28
29
A
Incremental Encoder Emulation Output A. Logic output. This output is free running and is valid if the resolver format
input signals applied to the converter are valid.
Incremental Encoder Emulation Output B. Logic output. This output is free running and is valid if the resolver format
input signals applied to the converter are valid.
North Marker Incremental Encoder Emulation Output. Logic output. This output is free running and is valid if the
resolver format input signals applied to the converter are valid.
Direction. Logic output. This output is used in conjunction with the incremental encoder emulation outputs. The DIR
output indicates the direction of the input rotation and is high for increasing angular rotation.
B
NM
DIR
DOS
Degradation of Signal. Logic output. Degradation of signal (DOS) is detected when either resolver input (Sin or Cos)
exceeds the specified DOS Sin/Cos threshold. See the Signal Degradation Detection section. DOS is indicated by a
logic low on the DOS pin and is not latched when the input signals exceed the maximum input level.
30
LOT
Loss of Tracking. Logic output. LOT is indicated by a logic low on the LOT pin and is not latched. See Loss of Signal
Detection section.
31
32
33
FS1
Frequency Select 1. Logic input. FSI in conjunction with FS2 allows the frequency of EXC/EXC to be programmed.
Frequency Select 2. Logic input. FS2 in conjunction with FS1 allows the frequency of EXC/EXC to be programmed.
FS2
RESET
Reset. Logic input. The AD2S1205 requires an external reset signal to hold the RESET input low until VDD is within the
specified operating range of 4.5 V to 5.5 V. See the Supply Sequencing and Reset section.
34
35
EXC
EXC
Excitiation Frequency. Analog output. An on-board oscillator provides the sinusoidal excitation signal (EXC) and its
complement signal (EXC) to the resolver. The frequency of this reference signal is programmable via the FS1 and FS2 pins.
Excitation Frequency Complement. Analog output. An on-board oscillator provides the sinusoidal excitation signal
(EXC) and its complement signal (EXC) to the resolver. The frequency of this reference signal is programmable via the
FS1 and FS2 pins.
36,
42
AGND
Analog Ground. These pins are ground reference points for analog circuitry on the AD2S1205. All analog input signals
and any external reference signal should be referred to this AGND voltage. Both of these pins should be connected to
the AGND plane of a system. The AGND and DGND voltages should ideally be at the same potential and must not be
more than 0.3 V apart, even on a transient basis.
37
38
39
Sin
SinLO
AVDD
Positive Analog Input of Differential Sin/SinLO Pair. The input range is 2.3 V p-p to 4.0 V p-p.
Negative Analog Input of Differential Sin/SinLO Pair. The input range is 2.3 V p-p to 4.0 V p-p.
Analog Supply Voltage, 4.75 V to 5.25 V. This pin is the supply voltage for all analog circuitry on the AD2S1205. The
AVDD and DVDD voltages ideally should be at the same potential and must not be more than 0.3 V apart, even on a
transient basis.
40
41
43
CosLO
Cos
REFBYP
Negative Analog Input of Differential Cos/CosLO Pair.
Positive Analog Input of Differential Cos/CosLO Pair.
Reference Bypass. Reference decoupling capacitors should be connected here. Typical recommended values are 10 μF
and 0.01 μF.
44
REFOUT
Voltage Reference Output, 2.39 V to 2.52 V.
Rev. 0 | Page 7 of 20
AD2S1205
RESOLVER FORMAT SIGNALS
V
= V × Sin(ωt)
V
= V × Sin(ωt)
r
p
r
p
R1
S2
S2
R1
R2
V
= V × Sin(ωt) × Cos(θ)
V
= V × Sin(ωt) × Cos(θ)
a
s
a
s
θ
θ
S4
S4
R2
S1
S3
S1
S3
V
= V × Sin(ωt) × Sin(θ)
V = V × Sin(ωt) × Sin(θ)
b s
b
s
(A) CLASSICAL RESOLVER
(B) VARIABLE RELUCTANCE RESOLVER
Figure 3. Classical Resolver vs. Variable Reluctance Resolver
A classical resolver is a rotating transformer that typically has a
primary winding on the rotor and two secondary windings on
the stator. A variable reluctance resolver, on the other hand, has the
primary and secondary windings on the stator and no windings
on the rotor, as shown in Figure 3; however, the saliency in this
rotor design provides the sinusoidal variation in the secondary
coupling with the angular position. For both designs, the resolver
output voltages (S3 − S1, S2 − S4) are as follows:
The stator windings are displaced mechanically by 90° (see
Figure 3). The primary winding is excited with an ac reference.
The amplitude of subsequent coupling onto the secondary
windings is a function of the position of the rotor (shaft)
relative to the stator. The resolver therefore produces two
output voltages (S3 − S1, S2 − S4), modulated by the sine and
cosine of the shaft angle. Resolver format signals refer to the
signals derived from the output of a resolver, as shown in
Equation 1. Figure 4 illustrates the output format.
S3 − S1 = E0Sin(ωt)× Sinθ
S2 − S4 = E0Sin(ωt)×Cosθ
(1)
where:
θ is the shaft angle.
S2 – S4
(COSINE)
Sin(ωt) is the rotor excitation frequency.
E0 is the rotor excitation amplitude.
S3 – S1
(SINE)
R2 – R4
(REFERENCE)
0°
90°
180°
270°
360°
θ
Figure 4. Electrical Resolver Representation
Rev. 0 | Page 8 of 20
AD2S1205
THEORY OF OPERATION
The incoming Sinθ and Cosθ signals are multiplied by the Sin
and Cos of the output angle, respectively, and then these values
are added together:
The AD2S1205’s operation is based on a Type II tracking closed-
loop principle. The digitally implemented tracking loop continually
tracks the position and velocity of the resolver without the need
for external convert and wait states. As the resolver moves through
a position equivalent to the least significant bit weighting, the
tracking loop output is updated by 1 LSB.
Monitor = (A1×Sinθ×Sinφ) + (A2×Cosθ ×Cosφ)
(5)
where:
A1 is the amplitude of the incoming Sin signal (A1 × Sinθ).
A2 is the amplitude of the incoming Cos signal (A2 × Cosθ).
θ is the resolver angle.
The converter tracks the shaft angle (θ) by producing an output
angle (ϕ) that is fed back and compared with the input angle
(θ); the difference between the two angles is the error, which is
driven towards 0 when the converter is correctly tracking the
input angle. To measure the error, S3 − S1 is multiplied by Cosϕ
and S2 − S4 is multiplied by Sinϕ to give
ϕ is the angle stored in the position register.
Note that Equation 5 is shown after demodulation with the
carrier signal Sin(ωt) removed. Also note that for a matched
input signal (that is, a no fault condition), A1 is equal to A2.
E0Sin(ωt)× SinθCosφ
E0Sin(ωt)×Cosθ Sinφ
for S3 − S1
for S2 − S4
(2)
When A1 is equal to A2 and the converter is tracking
(therefore, θ is equal to ϕ), the monitor signal output has a
constant magnitude of A1 (Monitor = A1 × (Sin2θ + Cos2θ) = A1),
which is independent of the shaft angle. When A1 does not
equal A2, the monitor signal magnitude alternates between A1
and A2 at twice the rate of the shaft rotation. The monitor
signal is used to detect degradation or loss of input signals.
The difference is taken, giving
E0Sin(ωt)×(Sinθ Cosφ−Cosθ Sinφ)
(3)
This signal is demodulated using the internally generated
synthetic reference, yielding
E0 (Sinθ Cosφ−Cosθ Sinφ)
(4)
LOSS OF SIGNAL DETECTION
Loss of signal (LOS) is detected when either resolver input (Sin
or Cos) falls below the specified LOS Sin/Cos threshold. The
AD2S1205 detects this by comparing the monitor signal to a
fixed minimum value. LOS is indicated by both DOS and LOT
latching as logic low outputs. The DOS and LOT pins are reset
Equation 4 is equivalent to E0Sin(θ − ϕ), which is approximately
equal to E0(θ − ϕ) for small values of θ − ϕ, where θ − ϕ is the
angular error.
The value E0(θ − ϕ) is the difference between the angular error
of the rotor and the digital angle output of the converter.
SAMPLE
to the no fault state by a rising edge of
. The LOS
condition has priority over both the DOS and LOT conditions,
as shown in Table 4. LOS is indicated within 5ꢀ° of the angular
output error (worst case).
A phase-sensitive demodulator, some integrators, and a compen-
sation filter form a closed-loop system that seeks to null the
error signal. If this is accomplished, ϕ equals the resolver angle
θ within the rated accuracy of the converter. A Type II tracking
loop is used so that constant velocity inputs can be tracked
without inherent error.
SIGNAL DEGRADATION DETECTION
Degradation of signal (DOS) is detected when either resolver input
(Sin or Cos) exceeds the specified DOS Sin/Cos threshold. The
AD2S1205 detects this by comparing the monitor signal to a
fixed maximum value. In addition, DOS is detected when the
amplitudes of the Sin and Cos input signals are mismatched by
more than the specified DOS Sin/Cos mismatch. This is
identified because the AD2S1205 continuously stores the
minimum and maximum magnitude of the monitor signal in
internal registers and calculates the difference between these
values. DOS is indicated by a logic low on the DOS pin and is
not latched when the input signals exceed the maximum input
level. When DOS is indicated due to mismatched signals, the
For more information about the operation of the converter, see
the Circuit Dynamics section.
FAULT DETECTION CIRCUIT
The AD2S1205 fault detection circuit can sense loss of resolver
signals, out-of-range input signals, input signal mismatch, or
loss of position tracking; however, the position indicated by the
AD2S1205 may differ significantly from the actual shaft
position of the resolver.
MONITOR SIGNAL
SAMPLE
output is latched low until a rising edge of
resets the
stored minimum and maximum values. The DOS condition has
priority over the LOT condition, as shown in Table 4. DOS is
indicated within 33° of the angular output error (worst case).
The AD2S1205 generates a monitor signal by comparing the
angle in the position register to the incoming Sin and Cos signals
from the resolver. The monitor signal is created in a similar fashion
to the error signal (described in the Theory of Operation section).
Rev. 0 | Page 9 of 20
AD2S1205
FALSE NULL CONDITION
LOSS OF POSITION TRACKING DETECTION
Resolver-to-digital converters that employ Type II tracking loops
based on the previously stated error equation (see Equation 4 in
the Theory of Operation section) can suffer from a condition
known as a false null. This condition is caused by a metastable
solution to the error equation when θ − ϕ = 180°. The AD2S1205
is not susceptible to this condition because its hysteresis is
implemented external to the tracking loop. As a result of the
loop architecture chosen for the AD2S1205, the internal error
signal constantly has some movement (1 LSB per clock cycle);
therefore, in a metastable state, the converter moves to an
unstable condition within one clock cycle. This causes the tracking
loop to respond to the false null condition as if it were a 180°
step change in input position (the response time is the same, as
specified in the Dynamic Performance section of Table 1).
Therefore, it is impossible to enter the metastable condition
after the start-up sequence if the resolver signals are valid.
Loss of tracking (LOT) is detected when
•
•
•
The internal error signal of the AD2S1205 exceeds 5°.
The input signal exceeds the maximum tracking rate.
The internal position (at the position integrator) differs
from the external position (at the position register) by
more than 5°.
LOT is indicated by a logic low on the LOT pin and is not
latched. LOT has a 4° hysteresis and is not cleared until the
internal error signal or internal/external position mismatch is
less than 1°. When the maximum tracking rate is exceeded,
LOT is cleared only if the velocity is less than the maximum
tracking rate and the internal/external position mismatch is less
than 1°. LOT can be indicated for step changes in position (such
RESET
as after a
signal is applied to the AD2S1205), or for
accelerations of >~65,000 rps2. It is also useful as a built-in test
to indicate that the tracking converter is functioning properly.
The LOT condition has lower priority than both the DOS and
LOS conditions, as shown in Table 4. The LOT and DOS
conditions cannot be indicated at the same time.
ON-BOARD PROGRAMMABLE SINUSOIDAL
OSCILLATOR
An on-board oscillator provides the sinusoidal excitation signal
EXC
(EXC) and its complement signal (
) to the resolver. The fre-
quency of this reference signal is programmable to four standard
frequencies (10 kHz, 12 kHz, 15 kHz, or 20 kHz) by using the
FS1 and FS2 pins (see Table 5). FS1 and FS2 have internal pull-ups,
so the default frequency is 10 kHz. The amplitude of this signal
is centered on 2.5 V and has an amplitude of 3.6 V p-p.
Table 4. Fault Detection Decoding
Order of
Condition
DOS Pin LOT Pin Priority
Loss of Signal (LOS)
Degradation of Signal (DOS)
Loss of Tracking (LOT)
No Fault
0
0
1
1
0
1
0
1
1
2
3
Table 5. Excitation Frequency Selection
Frequency Selection (kHz)
FS1
FS2
1
0
1
0
10
12
15
20
1
1
0
0
RESPONDING TO A FAULT CONDITION
If a fault condition (LOS, DOS, or LOT) is indicated by the
AD2S1205, the output data is presumed to be invalid. Even if a
RESET SAMPLE
or
pulse releases the fault condition and is not
immediately followed by another fault, the output data may be
corrupted. As discussed previously, there are some fault
conditions with inherent latency. If the device fault is cleared,
there may be some latency in the resolver’s mechanical position
before the fault condition is reindicated.
The frequency of the reference signal is a function of the CLKIN
frequency. By decreasing the CLKIN frequency, the minimum
excitation frequency can also be decreased. This allows an
excitation frequency of ꢀ.5 kHz to be set when using a CLKIN
frequency of 6.144 MHz, and it also decreases the maximum
tracking rate to ꢀ50 rps.
When a fault is indicated, all output pins still provide data, although
the data may or may not be valid. The fault condition does not
force the parallel, serial, or encoder outputs to a known state.
The reference output of the AD2S1205 requires an external buffer
amplifier to provide gain and additional current to drive the
resolver. See Figure 6 for a suggested buffer circuit.
Response to specific fault conditions is a system-level requirement.
The fault outputs of the AD2S1205 indicate that the device has
sensed a potential problem with either the internal or external
signals of the AD2S1205. It is the responsibility of the system
designer to implement the appropriate fault-handling schemes
within the control hardware and/or algorithm of a given appli-
cation based on the indicated fault(s) and the velocity or position
data provided by the AD2S1205.
The AD2S1205 also provides an internal synchronous reference
signal that is phase locked to its Sin and Cos inputs. Phase errors
between the resolver’s primary and secondary windings may
degrade the accuracy of the RDC and are compensated for by using
this synchronous reference signal. This also compensates for the
phase shifts due to temperature and cabling, and it eliminates the
need for an external preset phase-compensation circuit.
Rev. 0 | Page 10 of 20
AD2S1205
SYNTHETIC REFERENCE GENERATION
The gain of the circuit is
CarrierGain = −(R2/ R1)×(1/(1+ R2×C1×ω))
When a resolver undergoes a high rotation rate, the RDC tends
to act as an electric motor and produces speed voltages in
addition to the ideal Sin and Cos outputs. These speed voltages are
in quadrature to the main signal waveform. Moreover, nonzero
resistance in the resolver windings causes a nonzero phase shift
between the reference input and the Sin and Cos outputs. The
combination of the speed voltages and the phase shift causes a
tracking error in the RDC that is approximated by
(ꢀ)
and
R2
R1
R2
R1
⎛
⎞
⎛
⎝
⎞
⎟
⎠
⎛
⎜
⎝
⎞
⎟
⎠
VOUT = V × 1+
×(1/(1+R2×C1×ω)) −
×(1/(1+R2×C1×ω))V
⎜
⎟
⎜
REF
IN
⎝
⎠
(8)
where:
ω is the radian frequency of the applied signal.
RotationRate
ReferenceFrequency
Error = PhaseShift ×
(6)
VREF is set so that VOUT is always a positive value, eliminating the
need for a negative supply. A separate screened twisted pair cable
is recommended for analog inputs Sin/SinLO and Cos/CosLO.
The screens should terminate to either REFOUT or AGND.
To compensate for the described phase error between the resolver
reference excitation and the Sin/Cos signals, an internal synthetic
reference signal is generated in phase with the reference frequency
carrier. The synthetic reference is derived using the internally
filtered Sin and Cos signals. It is generated by determining the
zero crossing of either the Sin or Cos (whichever signal is
larger), which improves phase accuracy, and evaluating the phase
of the resolver reference excitation. The synthetic reference reduces
the phase shift between the reference and Sin/Cos inputs to less
than 10° and can operate for phase shifts of 45°.
S2
R2
R1
S4
S3
4.7μF
S1
5V
BUFFER
CIRCUIT
BUFFER
CIRCUIT
10nF
10nF
10μF
CHARGE-PUMP OUTPUT
44 43 42 41 40 39 38 37 36 35 34
A 204.8 kHz square wave output with a 507 duty cycle is available
at the CPO pin of the AD2S1205. This square wave output can
be used for negative rail voltage generation or to create a VCC rail.
RESET
1
2
DV
33
5V
DD
32
3
31
CONNECTING THE CONVERTER
4
30
5
29
Ground is connected to the AGND and DGND pins (see Figure 5).
A positive power supply (VDD) of 5 V dc 57 is connected to
the AVDD and DVDD pins, with typical values for the decoupling
capacitors being 10 nF and 4.ꢀ μF. These capacitors are then
placed as close to the device pins as possible and are connected
to both AVDD and DVDD. If desired, the reference oscillator
frequency can be changed from the nominal value of 10 kHz
using FS1 and FS2. Typical values for the oscillator decoupling
capacitors are 20 pF, whereas typical values for the reference
decoupling capacitors are 10 μF and 0.01 μF.
6
28
AD2S1205
7
27
8
26
9
25
24
10
11
DGND 23
12 13 14 15 16 17 18 19 20 21 22
5V
8.192
MHz
4.7μF
10nF
20pF
20pF
In this recommended configuration, the converter introduces a
VREF/2 offset in the Sin and Cos signal outputs from the resolver.
The SinLO and CosLO signals can each be connected to a different
potential relative to ground if the Sin and Cos signals adhere to the
Figure 5. Connecting the AD2S1205 to a Resolver
C1
12V
EXC
recommended specifications. Note that because the EXC and
outputs are differential, there is an inherent gain of 2×. Figure 6
shows a suggested buffer circuit. Capacitor C1 is recommended in
parallel with Resistor R2 to filter out any noise that may exist on the
R2
2.7kΩ
12V
12V
33Ω
R1
V
OUT
EXC/EXC
EXC
EXC and
outputs. The cutoff frequency of this filter needs
(V
)
IN
(V
REF
)
33Ω
2.7kΩ
to be carefully considered depending on the application needs.
Phase shifts of the carrier caused by the filter can effectively
skew the phase lock range of the AD2S1205.
442Ω
1.24kΩ
5V
Figure 6. Buffer Circuit
Rev. 0 | Page 11 of 20
AD2S1205
RD
from the selected register to the output register. Finally, the
CLOCK REQUIREMENTS
input is used to read the data from the output register and to
enable the output buffer. The timing requirements for the read
cycle are shown in Figure ꢀ.
To achieve the specified dynamic performance, an external crystal
is recommended at the CLKIN and XTALOUT pins. The position
and velocity accuracy are guaranteed for a frequency range of
8.192 MHz 257. However, the velocity outputs are scaled in
proportion to the clock frequency so that if the clock is 257
greater than the nominal, the full-scale velocity is 257 greater than
nominal. The maximum tracking rate, tracking loop bandwidth,
and excitation frequency also vary with the clock frequency.
SAMPLE
Input
Data is transferred from the position and velocity integrators to
the position and velocity registers, respectively, after a high-to-
SAMPLE
low transition on the
signal. This pin must be held
RD
low for at least t1 to guarantee correct latching of the data.
ABSOLUTE POSITION AND VELOCITY OUTPUT
should not be pulled low before this time because data will not
be ready. The converter continues to operate during the read
The angular position and velocity are represented by binary data
and can be extracted via either a 12-bit parallel interface or a
3-wire serial interface that operates at clock rates of up to 25 MHz.
SAMPLE
process. A rising edge of
resets the internal registers
that contain the minimum and maximum magnitude of the
monitor signal.
SOE
Input
CS
Input
SOE
The serial output enable pin (
) is held high to enable the
CS
The device is enabled when
is held low.
parallel interface and low to enable the serial interface. In the
latter case, Pins DB0 to DB9 are placed into a high impedance
state while DB11 is the serial output (SO) and DB10 is the serial
clock input (SCLK).
RDVEL
Input
RDVEL
input is used to select between the angular position
register and the angular velocity register, as shown in Figure ꢀ.
Data Format
RDVEL
is held high to select the angular position register and
The angular position data represents the absolute position of
the resolver shaft as a 12-bit unsigned binary word. The angular
velocity data is a 12-bit twos complement word, representing
the velocity of the resolver shaft rotating in either a clockwise or
counterclockwise direction.
RDVEL
pin is pulled low.
low to select the angular velocity register. The
pin must
RD
be set (stable) at least t4 before the
RD
Input
The 12-bit data bus lines are normally in a high impedance
CS RD
are held
state. The output buffer is enabled when
and
signal transfers data to the output
buffer. The selected data is made available to the bus to be read
RD
PARALLEL INTERFACE
RD
low. A falling edge of the
The angular position and velocity are available on the AD2S1205
in two 12-bit registers, accessed via the 12-bit parallel port. The
within t6 of the
impedance state when the
tꢀ. When reading data continuously, wait a minimum of t3 after
pin going low. The data pins return to a high
SOE
parallel interface is selected by holding the
pin high. Data
RD
pin returns to a high state within
is transferred from the velocity and position integrators to the
position and velocity registers, respectively, after a high-to-low
RD
is released before reapplying it.
SAMPLE
RDVEL
transition on the
data from the position or velocity register is transferred to the
CS
pin. The
pin selects whether
output register. The
pin must be held low to transfer data
Rev. 0 | Page 12 of 20
AD2S1205
fCLKIN
CLKIN
t1
t1
SAMPLE
CS
t2
t3
t3
RD
t5
t5
RDVEL
t4
t4
DATA
POSITION
VELOCITY
t7
t7
t6
DON'T CARE
t6
Figure 7. Parallel Port Read Timing
Table 6. Parallel Port Timing
Parameter
Description
Min
Typ
8.192
Max
Unit
MHz
ns
fCLKIN
t1
Frequency of clock input
SAMPLE pulse width
6.144
2 × (1/fCLKIN) + 20
10.24
t2
Delay from SAMPLE before RD/CS low
RD pulse width
6 × (1/fCLKIN) + 20
ns
t3
18
5
ns
t4
Set time RDVEL before RD/CS low
Hold time RDVEL after RD/CS low
Enable delay RD/CS low to data valid
Disable delay RD/CS low to data high-Z
ns
t5
7
ns
t6
16
18
ns
t7
ns
Rev. 0 | Page 13 of 20
AD2S1205
SAMPLE
Input
SERIAL INTERFACE
Data is transferred from the position and velocity integrators to
the position and velocity registers, respectively, after a high-to-
SAMPLE
The angular position and velocity are available on the AD2S1205
in two 12-bit registers. These registers can be accessed via a 3-wire
RD
low transition on the
signal. This pin must be held low
RD
serial interface (SO,
, and SCLK) that operates at clock rates
of up to 25 MHz and is compatible with SPI and DSP interface
SOE
for at least t1 to guarantee correct latching of the data.
should
standards. The serial interface is selected by holding the
pin
not be pulled low before this time because data will not be ready.
The converter continues to operate during the read process.
low. Data from the position and velocity integrators are first trans-
SAMPLE
ferred to the position and velocity registers using the
pin.
CS
Input
The device is enabled when
RD
RDVEL
The
pin selects whether data is transferred from the
CS
is held low.
CS
position or velocity register to the output register, and the pin
must be held low to transfer data from the selected register to the
Input
The 12-bit data bus lines are normally in a high impedance
CS RD
are held
RD
output register. Finally, the
input is used to read the data that is
clocked out of the output register and is available on the serial
output pin (SO). When the serial interface is selected, DB11 is used
as the serial output pin (SO), DB10 is used as the serial clock input
(SCLK), and pins DB0 to DB9 are placed into the high impedance
state. The timing requirements for the read cycle are described in
Figure 8.
state. The output buffer is enabled when
and
input is an edge-triggered input that acts as a frame
synchronization signal and an output enable. On a falling edge of
RD
RD
low. The
the
then available on the serial output pin (SO); however, it is only
RD
signal, data is transferred to the output buffer. Data is
valid after
is held low for t9. The serial data is clocked out of
SO Output
the SO pin on the rising edges of SCLK, and each data bit is
available at the SO pin on the falling edge of SCLK. However, as
the MSB is clocked out by the falling edge of
available at the SO pin on the first falling edge of SCLK. Each
subsequent bit of the data-word is shifted out on the rising edge
of SCLK and is available at the SO pin on the falling edge of
SCLK for the next 15 clock pulses.
The output shift register is 16 bits wide. Data is clocked out of
the device as a 16-bit word by the serial clock input (SCLK).
The timing diagram for this operation is shown in Figure 8. The
16-bit word consists of 12 bits of angular data (position or
RD
, the MSB is
RDVEL
RDVEL
velocity, depending on
input), one
status bit,
and three status bits (a parity bit, a degradation of signal bit, and a
loss of tracking bit). Data is clocked out MSB first from the SO
pin, beginning with DB15. DB15 through DB4 correspond to
the angular information. The angular position data format is
unsigned binary, with all 0s corresponding to 0° and all 1s
corresponding to 360° − l LSB. The angular velocity data format
is twos complement, with the MSB representing the rotation
status bit, with a 1 indicating
position and a 0 indicating velocity. DB2 is DOS, the
degradation of signal flag (refer to the Fault Detection Circuit
section). Bit 1 is LOT, the loss of tracking flag (refer to the Fault
Detection Circuit section). Bit 0 is PAR, the parity bit. The
position and velocity data are in odd parity format, and the data
readback always contains an odd number of logic highs (1s).
RD
The high-to-low transition of
time of the SCLK to avoid DB14 being shifted on the first rising
edge of the SCLK, which would result in the MSB being lost.
must occur during the high
RD
RD
may rise high after the last falling edge of SCLK. If
is
held low and additional SCLKs are applied after DB0 has been
read, then 0s will be clocked from the data output. When
reading data continuously, wait a minimum of t5 after
released before reapplying it.
RDVEL
direction. DB3 is the
RD
is
RDVEL
Input
RDVEL
input is used to select between the angular position
RDVEL
register and the angular velocity register.
is held high to
select the angular position register and low to select the angular
RDVEL
velocity register. The
pin must be set (stable) at least t4
pin is pulled low.
RD
before the
Rev. 0 | Page 14 of 20
AD2S1205
fCLKIN
CLKIN
t1
t1
SAMPLE
CS
t2
t3
t3
RD
t5
t5
RDVEL
t4
t4
t6
t6
t7
t7
SO
POSITION
VELOCITY
t8
RD
tSCLK
SCLK
t10
MSB – 1
t11
MSB
t9
LSB
RDVEL
DOS
LOT
PAR
SO
Figure 8. Serial Port Read Timing
Table 7. Serial Port Timing1
Parameter
Description
Min
Typ
Max
Unit
ns
t8
MSB read time RD/CS to SCLK
15
tSCLK
16
t9
SO enable time RD/CS to DB valid
ns
ns
ns
ns
t10
t11
tSCLK
Data access time, SCLK to DB valid
Bus relinquish time RD/CS to SO high-Z
Serial clock period (25 MHz maximum)
16
18
40
1 t1 to t7 are as defined in Table 6.
Rev. 0 | Page 15 of 20
AD2S1205
To achieve the maximum speed of ꢀ5,000 rpm, select an
external CLKIN of 10.24 MHz to produce an internal clock
frequency equal to 5.12 MHz.
INCREMENTAL ENCODER OUTPUTS
The A, B, and NM incremental encoder emulation outputs are
free running and are valid if the resolver format input signals
applied to the converter are valid.
This compares favorably with encoder specifications, which
state fMAX as 20 kHz (photo diodes) to 125 kHz (laser based),
depending on the type of light system used. A 1024-line laser-
based encoder has a maximum speed of ꢀ300 rpm.
The AD2S1205 emulates a 1024-line encoder, meaning that, in
terms of the converter resolution, one revolution produces 1024 A
and B pulses. Pulse A leads Pulse B for increasing angular rotation
(clockwise direction). The addition of the DIR output negates
the need for external A and B direction decode logic. The DIR
output indicates the direction of the input rotation and is high
for increasing angular rotation. DIR can be considered an asyn-
chronous output that can make multiple changes in state between
two consecutive LSB update cycles. This occurs when the direction
of the rotation of the input changes but the magnitude of the
rotation is less than 1 LSB.
The inclusion of A and B outputs allows an AD2S1205 and
resolver-based solution to replace optical encoders directly
without the need to change or upgrade the user’s existing
application software.
SUPPLY SEQUENCING AND RESET
The AD2S1205 requires an external reset signal to hold the
RESET
input low until VDD is within the specified operating
range of 4.5 V to 5.5 V.
The north marker pulse is generated as the absolute angular
position passes through zero. The north marker pulse width is
set internally for 90° and is defined relative to the A cycle.
Figure 9 details the relationship between A, B, and NM.
RESET
The
pin must be held low for a minimum of 10 μs after
V
DD is within the specified range (shown as tRST in Figure 10).
RESET
Applying a
signal to the AD2S1205 initializes the output
position to a value of 0x000 (degrees output through the parallel,
serial, and encoder interfaces) and causes LOS to be indicated
(LOT and DOS pins pulled low), as shown in Figure 10.
A
Failure to apply the correct power-up/reset sequence may result
in an incorrect position indication.
B
RESET
After a rising edge on the
input, the device must be
allowed at least 20 ms (shown as tTRACK in Figure 10) for the
internal circuitry to stabilize and the tracking loop to settle to
NM
Figure 9. A, B, and NM Timing for Clockwise Rotation
SAMPLE
the step change of the input position. After tTRACK, a
pulse must be applied, which in turn releases the LOT and DOT
pins to the state determined by the fault detection circuitry and
provides valid position data at the parallel and serial outputs.
(Note that if position data is acquired via the encoder outputs, it
can be monitored during tTRACK.)
Unlike incremental encoders, the AD2S1205 encoder output is
not subject to error specifications such as cycle error, eccentricity,
pulse and state width errors, count density, and phase ϕ. The
maximum speed rating (n) of an encoder is calculated from its
maximum switching frequency (fMAX) and its pulses per revo-
lution (PPR).
RESET
The
pin is then internally pulled up.
60× fMAX
n =
(9)
4.75V
PPR
V
DD
ttRST
The A and B pulses of the AD2S1205 are initiated from the inter-
nal clock frequency, which is exactly half the external CLKIN
frequency. With a nominal CLKIN frequency of 8.192 MHz,
the internal clock frequency is 4.096 MHz. The equivalent
encoder switching frequency is
RESET
tTRACK
SAMPLE
LOT
1/4× 4.096 MHz = 1.024 MHz (4 Updates= 1 Pulse) (10)
VALID
OUTPUT
DATA
For 12 bits, the PPR is 1024. Therefore, the maximum speed (n)
of the AD2S1205 with a CLKIN of 8.192 MHz is
DOS
60×1,024,000
n =
= 60,000 rpm
(11)
Figure 10. Power Supply Sequencing and Reset
1024
Rev. 0 | Page 16 of 20
AD2S1205
CIRCUIT DYNAMICS
R2D open-loop transfer function
LOOP RESPONSE MODEL
ERROR
(ACCELERATION)
G(z) = k1×k2× I(z)2 ×C(z)
(19)
(20)
VELOCITY
–1
c
1 – az
c
R2D closed-loop transfer function
θ
θ
OUT
k1 × k2
IN
–1
–1
–1
1 – z
1 – bz
1 – z
–
G(z)
H(z) =
1+ G(z)
Sin/Cos LOOKUP
Figure 11. RDC System Response Block Diagram
The closed-loop magnitude and phase responses are that of a
second-order low-pass filter (see Figure 12 and Figure 13).
The RDC is a mixed-signal device that uses two ADCs to
digitize signals from the resolver and a Type II tracking loop to
convert these to digital position and velocity words.
To convert G(z) into the s-plane, an inverse bilinear
transformation is performed by substituting the following
equation for z:
The first gain stage consists of the ADC gain on the Sin/Cos
inputs and the gain of the error signal into the first integrator.
The first integrator generates a signal proportional to velocity.
The compensation filter contains a pole and a zero that are used
to provide phase margin and reduce high frequency noise gain.
The second integrator is the same as the first and generates the
position output from the velocity signal. The Sin/Cos lookup has
unity gain. The values for each section are as follows:
2
+ s
t
z =
(21)
2
− s
t
where t is the sampling period (1/4.096 MHz ≈ 244 ns).
Substitution yields the open-loop transfer function G(s).
s2t2
4
ADC gain parameter (k1NOM = 1.8/2.5)
t(1+ a)
2(1− a)
t(1+ b)
1+ s ×
1+ s ×
1+ st +
k1×k2(1− a)
a −b
V
V
IN (Vp )
REF (V)
G(s) =
×
×
(22)
s2
(12)
k2 =
2(1−b)
Error gain parameter
This transformation produces the best matching at low frequencies
(f < fSAMPLE). At such frequencies (within the closed-loop bandwidth
of the AD2S1205), the transfer function can be simplified to
k2 = 18 × 106 × 2π
(13)
(14)
Compensator zero coefficient
Ka 1+ st1
G(s) ≅
×
(23)
s2 1+ st2
4095
4096
a =
where:
Compensator pole coefficient
t(1 + a)
2(1 − a)
t(1 + b)
2(1 − b)
t1 =
4085
4096
b =
(15)
(16)
(1ꢀ)
t2 =
Ka =
Integrator gain parameter
k1 × k2(1 − a)
a − b
1
c =
4,096,000
Solving for each value gives t1 = 1 ms, t2 = 90 μs, and Ka ≈ ꢀ.4 ×
106 s−2. Note that the closed-loop response is described as
INT1 and INT2 transfer function
c
I(z) =
1− z−1
G(s)
1+G(s)
(24)
H(s) =
Compensation filter transfer function
By converting the calculation to the s-domain, it is possible to
quantify the open-loop dc gain (Ka). This value is useful to
calculate the acceleration error of the loop (see the Sources of
Error section).
1−az −1
C(z) =
(18)
1−bz −1
Rev. 0 | Page 17 of 20
AD2S1205
The step response to a 10° input step is shown in Figure 14.
Because the error calculation (see Equation 2) is nonlinear for
large values of θ − ϕ, the response time for such large (90° to
180°) step changes in position typically takes three times as long
as the response to a small (<20°) step change in position. In
response to a step change in velocity, the AD2S1205 exhibits the
same response characteristics as it does for a step change in
position.
SOURCES OF ERROR
Acceleration
A tracking converter employing a Type II servo loop does not
have a lag in velocity. There is, however, an error associated
with acceleration. This error can be quantified using the
acceleration constant (Ka) of the converter.
Input Acceleration
Tracking Error
Ka =
(25)
5
–0
Conversely,
–5
Input Acceleration
–10
–15
–20
–25
–30
–35
–40
–45
Tracking Error =
(26)
Ka
Figure 15 shows tracking error vs. acceleration for the AD2S1205.
The units of the numerator and denominator must be consistent.
The maximum acceleration of the AD2S1205 is defined as the
acceleration that creates an output position error of 5° (that is,
when LOT is indicated). The maximum acceleration can be
calculated as
1
10
100
1k
10k
100k
100k
5
K a (sec−2 )×5°
360(°/rev)
FREQUENCY (Hz)
Maximum Acceleration =
≅ 103,000 rps2 (2ꢀ)
Figure 12. RDC System Magnitude Response
0
10
9
8
7
6
5
4
3
2
1
0
–20
–40
–60
–80
–100
–120
–140
–160
–180
–200
1
10
100
1k
10k
0
40k
80k
120k
160k
200k
2
FREQUENCY (Hz)
ACCELERATION (rps )
Figure 13. RDC System Phase Response
Figure 15. Tracking Error vs. Acceleration
20
18
16
14
12
10
8
6
4
2
0
0
1
2
3
4
TIME (ms)
Figure 14. RDC Small Step Response
Rev. 0 | Page 18 of 20
AD2S1205
RDVEL
and
can be obtained using two PIO outputs of the
CONNECTING TO THE DSP
ADMC401. The 12 bits of significant data and the status bits are
available on each consecutive negative edge of the clock after
The AD2S1205 serial port is ideally suited for interfacing to DSP-
configured microprocessors. Figure 16 shows the AD2S1205
interfaced to an ADMC401, one of the DSP-based motor
controllers.
RD
the
signal goes low. Data is clocked from the AD2S1205 into
the data receive register of the ADMC401. This is internally set
to 16 bits (12 data bits, 4 status bits) because 16 bits are received
overall. The serial port automatically generates an internal
processor interrupt. This allows the ADMC401 to read all 16
bits and then continue to process data.
The on-chip serial port of the ADMC401 is used in the following
configuration
•
•
•
Alternate framing transmit mode with internal framing
(internally inverted)
All ADMC401 products can interface to the AD2S1205 by using
similar interface circuitry.
Normal framing receive mode with external framing
(internally inverted)
ADMC401
AD2S1205
SCLK
DR
SCLK SOE
Internal serial clock generation
SO
RD
In this configuration, the internal TFS signal of ADMC401
is used as an external RFS to fully control the timing of
TFS
RFS
RD
data received, and the same TFS is connected to
AD2S1205. In addition, the ADMC401 provides an internal
SAMPLE
of the
PWMSYNC
PIO
SAMPLE
CS
continuous serial clock to the AD2S1205. The
signal
on the AD2S1205 can be provided either by using a PIO or by
inverting the PWMSYNC signal to synchronize the position
PIO
RDVEL
Figure 16. Connecting to the ADMC401
CS
and velocity readings with the PWM switching frequency.
Rev. 0 | Page 19 of 20
AD2S1205
OUTLINE DIMENSIONS
12.20
12.00 SQ
11.80
0.75
0.60
0.45
1.60
MAX
44
34
1
33
PIN 1
10.20
10.00 SQ
9.80
TOP VIEW
(PINS DOWN)
1.45
1.40
1.35
0.20
0.09
7°
3.5°
0°
11
23
0.15
0.05
12
22
SEATING
PLANE
0.10
COPLANARITY
VIEW A
0.45
0.37
0.30
0.80
BSC
LEAD PITCH
VIEW A
ROTATED 90° CCW
COMPLIANT TO JEDEC STANDARDS MS-026-BCB
Figure 17. 44-Lead Low Profile Quad Flat Package [LQFP]
(ST-44-1)
Dimensions shown in millimeters
ORDERING GUIDE
Temperature
Range
Model
Angular Accuracy
11 arc min
22 arc min
Package Description
Package Option
ST-44-1
ST-44-1
AD2S1205YSTZ1
AD2S1205WSTZ1
EVAL-AD2S1205CBZ1, 2
EVAL-CONTROL BRD23
−40°C to +125°C
−40°C to +125°C
44-Lead Low Profile Quad Flat Package [LQFP]
44-Lead Low Profile Quad Flat Package [LQFP]
Evaluation Board
Controller Board
1 Z = Pb-free part.
2 This can be used either as a standalone evaluation board or in conjunction with the evaluation board controller for evaluation/demonstration purposes.
3 Evaluation board controller. This board is a complete unit that allows a PC to control and communicate with all Analog Devices evaluation boards ending in the CB
designator. For a complete evaluation kit, order the ADC evaluation board (that is, the EVAL-AD2S1205CBZ), the EVAL-CONTROL BRD2, and a 12 V ac transformer.
©2007 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06339-0-1/07(0)
Rev. 0 | Page 20 of 20
相关型号:
©2020 ICPDF网 联系我们和版权申明