OP200GSZ [ADI]
Dual Low Offset, Low Power Operational Amplifier; 双低失调,低功耗运算放大器型号: | OP200GSZ |
厂家: | ADI |
描述: | Dual Low Offset, Low Power Operational Amplifier |
文件: | 总16页 (文件大小:329K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Dual Low Offset, Low Power
Operational Amplifier
Data Sheet
OP200
FEATURES
PIN CONNECTIONS
Low input offset voltage: 75 µV maximum
Low offset voltage drift, over −55°C < TA < +125°C
0.5 µV/°C maximum
Low supply current (per amplifier): 725 µA maximum
High open-loop gain: 5000 V/mV minimum
Low input bias current: 2 nA maximum
Low noise voltage density: 11 nV/√Hz at 1 kHz
Stable with large capacitive loads: 10 nF typical
–IN A
+IN A
NC
1
2
3
4
5
6
7
8
16 OUT A
15 NC
14 NC
V–
13 V+
NC
12 NC
+IN B
–IN B
NC
11 NC
10 OUT B
9
NC
NC = NO CONNECT
Figure 1. 16-Lead SOIC (S-Suffix)
OUT A
–IN A
+IN A
V–
1
2
3
4
8
7
6
5
V+
OP200
A
OUT B
–IN B
+IN B
B
Figure 2. 8-Lead PDIP (P-Suffix)
8-Lead CERDIP (Z-Suffix)
GENERAL DESCRIPTION
The OP200 is the first monolithic dual operational amplifier
to offer OP77 type precision performance. Available in the
industry standard 8-lead pinout, the OP200 combines precision
performance with the space and cost savings offered by a dual
amplifier.
Power consumption of the OP200 is low, with each amplifier
drawing less than 725 µA of supply current. The total current
drawn by the dual OP200 is less than one-half that of a single
OP07, yet the OP200 offers significant improvements over this
industry-standard op amp. The voltage noise density of the
OP200, 11 nV/√Hz at 1 kHz, is half that of most competitive
devices.
The OP200 features an extremely low input offset voltage of
less than 75 µV with a drift below 0.5 µV/°C, guaranteed over
the full military temperature range. Open-loop gain of the OP200
exceeds 5,000,000 into a 10 kΩ load; input bias current is under
2 nA; CMRR is over 120 dB; and PSRR is below 1.8 µV/V. On-chip
Zener zap trimming is used to achieve the extremely low input
offset voltage of the OP200 and eliminates the need for offset
pulling.
The OP200 is pin compatible with the OP221, LM158,
MC1458/MC1558, and LT1013.
The OP200 is an ideal choice for applications requiring multiple
precision op amps and where low power consumption is critical.
For a quad precision op amp, see the OP400.
Rev. E
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rightsof third parties that may result fromits use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks andregisteredtrademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©1978–2012 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
OP200
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Applications Information .............................................................. 12
Dual Low Power Instrumentation Amplifier ......................... 12
Precision Absolute Value Amplifier......................................... 12
Precision Current Pump............................................................ 12
Dual 12-Bit Voltage Output DAC ............................................ 13
Dual Precision Voltage Reference ............................................ 13
Programmable High Resolution Window Comparator........ 14
Outline Dimensions ....................................................................... 15
Ordering Guide .......................................................................... 16
Pin Connections ............................................................................... 1
General Description ......................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 4
Electrical Characteristics............................................................. 4
Absolute Maximum Ratings............................................................ 7
Thermal Resistance ...................................................................... 7
ESD Caution.................................................................................. 7
Typical Performance Characteristics ............................................. 8
REVISION HISTORY
2/04—Data Sheet changed from Rev. A to Rev. B.
9/12—Rev. D to Rev. E
OP200F Deleted..................................................................Universal
Changes to Ordering Guide.............................................................5
Changes to Figure 4...........................................................................8
Updated Outline Dimension ........................................................ 11
Changed Table 2 Conditions from VS = 15 V to VS = 15 V...... 4
Updated Outline Dimensions....................................................... 15
Changes to Ordering Guide .......................................................... 16
2/09—Rev. C to Rev. D
4/02—Data Sheet changed from Rev. 0 to Rev. A.
Change to Large Signal Voltage Gain, Table 2.............................. 4
Changes to Ordering Guide .......................................................... 16
Edits to Features.................................................................................1
Edits to General Description ...........................................................1
Edits to Ordering Information ........................................................1
Edits to Pin Connections..................................................................1
Edits to Absolute Maximum Ratings..............................................2
Edits to Package Type .......................................................................2
8/08—Rev. B to Rev. C
Updated Format..................................................................Universal
Changes to Features Section............................................................ 1
Changes to Table 1 and Table 2....................................................... 4
Changes to Table 3 and Table 4....................................................... 5
Deleted Table 7; Renumbered Sequentially................................... 5
Changes to Figure 15........................................................................ 9
Changes to Figure 21...................................................................... 10
Changes to Figure 30 and Figure 31............................................. 12
Changes to Programmable High Resolution Window
Comparator Section, Figure 33, and Figure 34........................... 13
Changes to Figure 35...................................................................... 14
Updated Outline Dimensions....................................................... 15
Changes to Ordering Guide .......................................................... 16
Rev. E | Page 2 of 16
Data Sheet
OP200
V+
BIAS
OUT
VOLTAGE
LIMITING
NETWORK
+IN
–IN
V–
Figure 3. Simplified Schematic (One of Two Amplifiers Shown)
Rev. E | Page 3 of 16
OP200
Data Sheet
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS
VS = 15 V, TA = 25°C, unless otherwise noted.
Table 1.
OP200A/E
Typ
OP200G
Typ
Parameter
Symbol
Conditions
Min
Max
Min
Max
Unit
INPUT CHARACTERISTICS
Input Offset Voltage
Long-Term Input Voltage Stability
Input Offset Current
Input Bias Current
VOS
25
75
80
200
μV
μV/mo
nA
0.1
0.05
0.1
0.5
22
11
15
0.4
10
125
0.1
0.05
0.1
0.5
22
11
15
0.4
10
125
IOS
IB
en p-p
en
VCM = 0 V
VCM = 0 V
1.0
2.0
3.5
5.0
nA
Input Noise Voltage
Input Noise Voltage Density1
0.1 Hz to 10 Hz
fO = 10 Hz
fO = 1000 Hz
0.1 Hz to 10 Hz
fO = 10 Hz
μV p-p
nV/√Hz
nV/√Hz
pA p-p
pA/√Hz
MΩ
36
18
Input Noise Current
in p-p
in
RIN
RINCM
AVO
Input Noise Current Density
Input Resistance Differential Mode
Input Resistance Common Mode
Large Signal Voltage Gain
GΩ
VO = 10 V
RL = 10 kΩ
RL = 2 kΩ
5000
2000
12000
3700
3000
1500
7000
3200
M/mV
M/mV
1 Sample tested.
VS = 15 V, −55°C ≤ TA ≤ +125°C for OP200A, unless otherwise noted.
Table 2.
OP200A
Typ
Parameter
Symbol
Conditions
Min
Max
Unit
INPUT CHARACTERISTICS
Input Offset Voltage
Average Input Offset Voltage Drift
Input Offset Current
Input Bias Current
VOS
TCVOS
IOS
IB
AVO
45
125
0.5
2.5
5.0
μV
μV/°C
nA
0.2
0.15
0.9
VCM = 0 V
VCM = 0 V
VO = 10 V
RL = 10 kΩ
RL = 2 kΩ
nA
Large Signal Voltage Gain
3000
1000
12
9000
2700
12.5
130
8
V/mV
V/mV
V
dB
nF
Input Voltage Range1
Common-Mode Rejection Ratio
Capacitive Load Stability
POWER SUPPLY
IVR
CMRR
VCM = 12 V
AV = 1
115
Power Supply Rejection Ratio
Supply Current Per Amplifier
OUTPUT CHARACTERISTICS
Output Voltage Swing
PSRR
ISY
VS = 3 V to 18 V
No load
0.2
600
3.2
775
μV/V
μA
VO
RL = 10 kΩ
RL = 2 kΩ
12
11
12.4
12
V
V
1 Guaranteed by CMRR test.
Rev. E | Page 4 of 16
Data Sheet
OP200
VS = 15 V, TA = 25°C, unless otherwise noted.
Table 3.
OP200A/E
Typ
OP200G
Typ
Parameter
Symbol Conditions
Min
Max
Min
Max
Unit
INPUT CHARACTERISTICS
Input Voltage Range1
Common-Mode Rejection Ratio
Channel Separation2
Input Capacitance
Capacitive Load Stability
POWER SUPPLY
IVR
CMRR
CS
12
120
13
135
145
3.2
12
110
123
13
130
145
3.2
V
VCM = 12 V
dB
dB
pF
nF
VO = 20 V p-p, fO = 10 Hz 123
CIN
AV = 1, no oscillations
10
10
Power Supply Rejection Ratio
Supply Current Per Amplifier
OUTPUT CHARACTERISTICS
Output Voltage Swing
PSRR
ISY
VS = 3 V to 18 V
No load
0.4
570
1.8
725
0.6
570
5.6
725
μV/V
μA
VO
RL= 10 kΩ
RL = 2 kΩ
12
11
12.6
12.2
12
11
12.6
12.2
V
V
DYNAMIC PERFORMANCE
Slew Rate
Gain Bandwidth Product
SR
GBP
0.1
0.15
500
0.1
0.15
500
V/μs
kHz
AV = 1
1 Guaranteed by CMRR test.
2 Guaranteed but not 100% tested.
VS = 15 V, −40°C ≤ TA ≤ +85°C, unless otherwise noted.
Table 4.
OP200E
Typ
OP200G
Typ
Parameter
Symbol Conditions
Min
Max
Min
Max
Unit
INPUT CHARACTERISTICS
Input Offset Voltage
Average Input Offset Voltage Drift
Input Offset Current
Input Bias Current
VOS
TCVOS
IOS
IB
AVO
35
100
0.5
2.5
5.0
110
0.6
0.1
0.5
300
2.0
6.0
μV
μV/°C
nA
0.2
0.08
0 3
VCM = 0 V
VCM = 0 V
VO = 10 V
RL= 10 kΩ
RL = 2 kΩ
10.0
nA
Large-Signal Voltage Gain
3000
1500
12
10,000
3200
12.5
130
2000 5000
1000 2500
V/mV
V/mV
V
dB
nF
Input Voltage Range1
Common-Mode Rejection Ratio
Capacitive Load Stability
POWER SUPPLY
IVR
CMRR
12
105
12.5
130
10
VCM = 12 V
AV = 1, no oscillations
115
10
Power Supply Rejection Ratio
Supply Current Per Amplifier
OUTPUT CHARACTERISTICS
Output Voltage Swing
PSRR
ISY
VS = 3 V to 18 V
No load
0.15
600
3.2
775
0.3
600
10.0
775
μV/V
μA
VO
RL = 10 kΩ
RL = 2 kΩ
12
11
12.4
12
12
11
12.4
12.2
V
V
1 Guaranteed by CMRR test.
Rev. E | Page 5 of 16
OP200
Data Sheet
1/2
V
1
20V p-p @ 10Hz
OP200
50Ω
50Ω
1/2
V
2
OP200
V
1
CHANNEL SEPARATION = 20 log
V /1000
2
Figure 4. Channel Separation Test Circuit
100Ω
10kΩ
1/2
TO SPECTRUM
ANALYZER
e
OUT
OP200
1/2
OP200
e
(nV/√Hz) = √2 × e
(nV/√Hz) × 101
OUT
OUT
Figure 5. Noise Test Schematic
Rev. E | Page 6 of 16
Data Sheet
OP200
ABSOLUTE MAXIMUM RATINGS
Table 5.
THERMAL RESISTANCE
Table 6.
Package Type
Parameter
Rating
1
Supply Voltage
20 V
θJA
θJC
16
37
27
Unit
°C/W
°C/W
°C/W
Differential Input Voltage
Input Voltage
30 V
8-Lead CERDIP (Z Suffix)
8-Lead Plastic DIP (P Suffix)
16-Lead SOIC (S Suffix)
148
96
92
Supply voltage
Continuous
−65°C to +150°C
300°C
Output Short-Circuit Duration
Storage Temperature Range
Lead Temperature (Soldering, 60 sec)
Junction Temperature Range (TJ)
Operating Temperature Range
OP200A
1 θJA is specified for worst-case mounting conditions, that is, θJA is specified for
device in socket for CERDIP and PDIP packages; θJA is specified for device
soldered to printed circuit board for SOIC package.
−65°C to +150°C
ESD CAUTION
−55°C to +125°C
−40°C to +85°C
OP200E, OP200G
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. E | Page 7 of 16
OP200
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
300
250
200
150
100
50
V
= ±15V
T
V
= 25°C
= ±15V
S
A
S
2
1
0
0
–75
–50
–25
0
25
50
75
100
125
0
1.0
2.0
3.0
4.0
5.0
TEMPERATURE (°C)
TIME (Minutes)
Figure 6. Warm-Up Drift
Figure 9. Input Offset Current vs. Temperature
1.0
0.8
0.6
0.4
0.2
0
60
50
40
30
20
10
0
T
V
= 25°C
= ±15V
V
= ±15V
A
S
S
–15
–10
–5.0
0
5.0
10
15
–75
–50
–25
0
25
50
75
100
125
COMON-MODE VOLTAGE (V)
TEMPERATURE (°C)
Figure 7. Input Offset Voltage vs. Temperature
Figure 10. Input Bias Current vs. Common-Mode Voltage
140
120
100
80
3
T
= 25°C
V = ±15V
S
A
V
= ±15V
S
2
1
0
60
–1
–2
–3
40
20
0
1
10
100
1k
10k
100k
–75
–50
–25
0
25
50
75
100
125
FREQUENCY (Hz)
TEMPERATURE (°C)
Figure 11. Common-Mode Rejection vs. Frequency
Figure 8. Input Bias Current vs. Temperature
Rev. E | Page 8 of 16
Data Sheet
OP200
100
1.18
1.16
1.14
1.12
1.10
1.08
1.06
T
V
= 25°C
= ±15V
A
TWO AMPLIFIERS
= 25°C
S
T
A
10
1
10
100
FREQUENCY (Hz)
1k
±2
±6
±10
±14
±18
SUPPLY VOLTAGE (V)
Figure 12. Voltage Noise Density vs. Frequency
Figure 15. Total Supply Current vs. Supply Voltage
1000
1.16
1.15
1.14
1.13
1.12
1.11
T
V
= 25°C
= ±15V
A
TWO AMPLIFIERS
S
V
= ±15V
S
100
1
10
100
FREQUENCY (Hz)
1k
–75
–50
–25
0
25
50
75
100
125
TEMPERATURE (°C)
Figure 13. Current Noise Density vs. Frequency
Figure 16. Total Supply Current vs. Temperature
140
120
100
80
NEGATIVE SUPPLY
60
POSITIVE SUPPLY
40
20
T
= 25°C
1
A
0
0.1
10
100
FREQUENCY (Hz)
1k
10k
100k
0
2
4
6
8
10
TIME (SEC)
Figure 14. 0.1 Hz to 10 Hz Noise
Figure 17. Power Supply Rejection vs. Frequency
Rev. E | Page 9 of 16
OP200
Data Sheet
0.7
0.6
0.5
0.4
0.3
0.2
0.1
140
120
100
80
T
V
= 25°C
= ±15V
A
S
A
= 1000
V
A
A
= 100
= 10
V
V
60
40
A
= 1
V
20
0
–75
–50
–25
0
25
50
75
100
125
1
10
100
1k
10k
100k
1M
TEMPERATURE (°C)
FREQUENCY (Hz)
Figure 18. Power Supply Rejection vs. Temperature
Figure 21. Closed-Loop Gain vs. Frequency
6000
5000
4000
3000
2000
1000
0
30
25
20
15
10
5
T
V
= 25°C
= ±15V
V
R
= ±15V
= 2kΩ
A
S
S
L
V p-p AT 1%
DISTORTION
0
10
–75
–50
–25
0
25
50
75
100
125
100
1k
10k
100k
TEMPERATURE (°C)
FREQUENCY (Hz)
Figure 19. Open-Loop Gain vs. Temperature
Figure 22. Maximum Output Swing vs. Frequency
140
120
100
80
1
T
V
= 25°C
= ±15V
A
A
= 100
= 10
A
V
V
S
0.1
A
= 1
V
0
60
PHASE
40
90
0.01
GAIN
10k
135
180
20
T
= 25°C
A
V
= ±15V
S
V
R
= 10V p-p
0
OUT
= 2kΩ
L
0.001
–20
10
100
1k
100k
1M
100
1k
10k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 20. Open-Loop Gain and Phase Shift vs. Frequency
Figure 23. Total Harmonic Distortion vs. Frequency
Rev. E | Page 10 of 16
Data Sheet
OP200
50
T
V
= 25°C
= ±15V
A
45
40
35
30
25
20
15
10
5
S
FALLING
RISING
T
V
A
= 25°C
= ±15V
= +1
A
0
S
0
0.5
1.0
1.5
2.0
2.5
3.0
V
5.00V
100µs
CAPACITIVE LOAD (nF)
Figure 27. Large Signal Transient Response
Figure 24. Overshoot vs. Capacitive Load
29
28
27
26
25
24
23
22
T
V
= 25°C
= ±15V
A
S
SINKING
T
V
A
= 25°C
= ±15V
= +1
A
SOURCING
S
V
0
1
2
3
4
5
20mV
5µs
TIME (Minutes)
Figure 25. Short-Circuit Current vs. Time
Figure 28. Small Signal Transient Response
150
140
130
120
110
100
90
T
V
A
= 25°C
= ±15V
= +1
A
S
V
10
100
1k
10k
100k
20mV
5µs
FREQUENCY (Hz)
Figure 26. Channel Separation vs. Frequency
Figure 29. Small Signal Transient Response, CLOAD = 1 nF
Rev. E | Page 11 of 16
OP200
Data Sheet
APPLICATIONS INFORMATION
The OP200 is inherently stable at all gains and is capable of
driving large capacitive loads without oscillating. Nonetheless,
good supply decoupling is highly recommended. Proper supply
decoupling reduces problems caused by supply line noise and
improves the capacitive load driving capability of the OP200.
PRECISION ABSOLUTE VALUE AMPLIFIER
The circuit in Figure 31 is a precision absolute value amplifier
with an input impedance of 10 MΩ. The high gain and low TCVOS
of the OP200 ensure accurate operation with microvolt input
signals. In this circuit, the input always appears as a common-
mode signal to the op amps. The CMRR of the OP200 exceeds
120 dB, yielding an error of less than 2 ppm.
DUAL LOW POWER INSTRUMENTATION
AMPLIFIER
+15V
A dual instrumentation amplifier that consumes less than 33 mW
of power per channel is shown in Figure 30. The linearity of the
instrumentation amplifier exceeds 16 bits in gains of 5 to 200 and is
better than 14 bits in gains from 200 to 1000. CMRR is above
115 dB (gain = 1000). Offset voltage drift is typically 0.2 μV/°C
over the military temperature range, which is comparable to the
best monolithic instrumentation amplifiers. The bandwidth of
the low power instrumentation amplifier is a function of gain
and is shown in Table 7.
C2
0.1pF
R1
R3
1kΩ
1kΩ
C1
6
5
30pF
D1
1N4148
7
1/2
OP200AZ
8
2
3
V
OUT
1/2
1
0V < V
< 10V
OP200AZ
OUT
D1
1N4148
V
IN
4
R2
2kΩ
C2
0.1pF
Table 7. Gain Bandwidth
Gain
Bandwidth
150 kHz
67 kHz
–15V
5
10
Figure 31. Precision Absolute Value Amplifier
100
1000
7.5 kHz
500 Hz
PRECISION CURRENT PUMP
The maximum output current of the precision current pump
shown in Figure 32 is 10 mA. Voltage compliance is 10 V
with 15 V supplies. Output impedance of the current transmit-
ter exceeds 3 MΩ with linearity better than 16 bits.
+15V
8
3
2
+
1/2
OP200AZ
1
V
R3
10kΩ
IN
V
OUT
5
6
–
1/2
7
4
–15V
20kΩ
OP200AZ
R1
10kΩ
2
3
R5
–
100Ω
1/2
OP200EZ
1
20kΩ
5kΩ
5kΩ
V
R1
10kΩ
IN
I
OUT
V
REF
+
R
G
+15V
40,000
V
=
5 +
V
+ V
IN REF
OUT
R
G
8
5
6
R4
1kΩ
1/2
OP200EZ
7
Figure 30. Dual Low Power Instrumentation Amplifier
V
V
The output signal is specified with respect to the reference
input, which is normally connected to analog ground. The
IN
IN
4
I
=
=
= 10mA/V
OUT
RS 100Ω
reference input can be used to offset the output from −10 V
to +10 V if required.
–15V
Figure 32. Precision Current Pump
Rev. E | Page 12 of 16
Data Sheet
OP200
DUAL 12-BIT VOLTAGE OUTPUT DAC
DUAL PRECISION VOLTAGE REFERENCE
The dual output DAC shown in Figure 33 is capable of providing
untrimmed 12-bit accurate operation over the entire military
temperature range. Offset voltage, bias current, and gain errors
of the OP200 contribute less than 1/10 of an LSB error at 12 bits
over the military temperature range.
A dual OP200 and a REF43, a 2.5 V reference, can be used to
build a 2.5 V precision voltage reference. Maximum output
current from each reference is 10 mA with load regulation
under 25 μV/mA. Line regulation is better than 15 μV/V and
output voltage drift is under 20 μV/°C. Output voltage noise
from 0.1 Hz to 10 Hz is typically 75 μV p-p. R1 and D1 ensure
correct startup.
5V
21
V
DD
R
8
3
2
FB A
DAC8221
10V
REFERENCE
VOLTAGE
DAC A
1/2
V
I
OUT A
2
REF A
4
1/2
DAC8221
1
4
OUT A
V–
OP200AZ
3
DAC DATA BUS
PIN 6 (MSB) TO PIN 17 (LSB)
R
23
24
FB B
DAC B
1/2
DAC8221
V
22
I
OUT B
REF B
6
5
1/2
OP200AZ
7
OUT B
18
19
20
DAC A/DAC B
AGND
1
DAC
CONTROL
CS
WR
DGND
5
Figure 33. Dual 12-Bit Voltage Output DAC
+5V
R1
22kΩ
D1
1N914
+2.5V
+5V
8
R3
10kΩ
V
IN
2
6
5
2
3
R3
10kΩ
V
OUT
REF43
TRIM
1/2
OP200AZ
1
6
5
1/2
OP200AZ
7
4
4
GND
R4
5kΩ
–5V
–2.5V
Figure 34. Dual Precision Voltage Reference
Rev. E | Page 13 of 16
OP200
Data Sheet
range. A dual CMOS 12-bit DAC, the DAC8221, is used in the
voltage switching mode to set the upper and lower thresholds
(DAC A and DAC B, respectively).
PROGRAMMABLE HIGH RESOLUTION WINDOW
COMPARATOR
The programmable window comparator shown in Figure 35 is
easily capable of 12-bit accuracy over the full military temperature
15V
V
IN
21
DD
V
8
10V
REFERENCE
VOLTAGE
DAC A
1/2
DAC8221
I
V
OUT A
4
3
2
2
REF A
1/2
OP200AZ
1
R1
10kΩ
5V
D1
1N4148
R2
10kΩ
TTL OUT
4
DAC DATA BUS
PIN 6 (MSB) TO PIN 17 (LSB)
15V–
Q1
2N2222
D1
1N4148
R2
10kΩ
R4
10kΩ
5
6
1/2
OP200AZ
7
DAC B
I
V
24
OUT B
22
REF B
1/2
DAC8221
18
19
20
DAC A/DAC B
CS
DAC
CONTROL
SIGNALS
WR
DGND
AGND
1
5
Figure 35. Programmable High Resolution Window Comparator
Rev. E | Page 14 of 16
Data Sheet
OP200
OUTLINE DIMENSIONS
0.005 (0.13)
MIN
0.055 (1.40)
MAX
8
5
0.310 (7.87)
0.220 (5.59)
1
4
0.100 (2.54) BSC
0.405 (10.29) MAX
0.320 (8.13)
0.290 (7.37)
0.060 (1.52)
0.015 (0.38)
0.200 (5.08)
MAX
0.150 (3.81)
MIN
0.200 (5.08)
0.125 (3.18)
0.015 (0.38)
0.008 (0.20)
SEATING
PLANE
0.023 (0.58)
0.014 (0.36)
15°
0°
0.070 (1.78)
0.030 (0.76)
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 36. 8-Lead Ceramic Dual In-Line Package [CERDIP]
(Q-8)
Z-Suffix
Dimensions shown in inches and (millimeters)
0.400 (10.16)
0.365 (9.27)
0.355 (9.02)
8
1
5
4
0.280 (7.11)
0.250 (6.35)
0.240 (6.10)
0.325 (8.26)
0.310 (7.87)
0.300 (7.62)
0.100 (2.54)
BSC
0.060 (1.52)
MAX
0.195 (4.95)
0.130 (3.30)
0.115 (2.92)
0.210 (5.33)
MAX
0.015
(0.38)
MIN
0.150 (3.81)
0.130 (3.30)
0.115 (2.92)
0.015 (0.38)
GAUGE
0.014 (0.36)
0.010 (0.25)
0.008 (0.20)
PLANE
SEATING
PLANE
0.022 (0.56)
0.018 (0.46)
0.014 (0.36)
0.430 (10.92)
MAX
0.005 (0.13)
MIN
0.070 (1.78)
0.060 (1.52)
0.045 (1.14)
COMPLIANT TO JEDEC STANDARDS MS-001
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS.
Figure 37. 8-Lead Plastic Dual In-Line Package [PDIP]
(N-8)
P-Suffix
Dimensions shown in inches and (millimeters)
Rev. E | Page 15 of 16
OP200
Data Sheet
10.50 (0.4134)
10.10 (0.3976)
16
1
9
8
7.60 (0.2992)
7.40 (0.2913)
10.65 (0.4193)
10.00 (0.3937)
0.75 (0.0295)
0.25 (0
.0098)
1.27 (0.0500)
BSC
45°
2.65 (0.1043)
2.35 (0.0925)
0.30 (0.0118)
0.10 (0.0039)
8°
0°
COPLANARITY
0.10
SEATING
PLANE
0.51 (0.0201)
0.31 (0.0122)
1.27 (0.0500)
0.40 (0.0157)
0.33 (0.0130)
0.20 (0.0079)
COMPLIANT TO JEDEC STANDARDS MS-013-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 38. 16-Lead Standard Small Outline Package [SOIC_W]
Wide Body
(RW-16)
S-Suffix
Dimensions shown in millimeters and (inches)
ORDERING GUIDE
Model1
TA = 25°C VOS Max (μV) Temperature Range
Package Description
Package Option
OP200AZ
OP200EZ
OP200GPZ
OP200GS
OP200GSZ
OP200GSZ-REEL
75
75
200
200
200
200
−55°C to +125°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
8-Lead CERDIP
8-Lead CERDIP
8-Lead PDIP
16-Lead SOIC_W
16-Lead SOIC_W
16-Lead SOIC_W
Z-Suffix (Q-8)
Z-Suffix (Q-8)
P-Suffix (N-8)
S-Suffix (RW-16)
S-Suffix (RW-16)
S-Suffix (RW-16)
1 Z = RoHS Compliant Part.
©1978–2012 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D00322-0-9/12(E)
Rev. E | Page 16 of 16
相关型号:
OP207AY
IC DUAL OP-AMP, 230 uV OFFSET-MAX, 0.6 MHz BAND WIDTH, CDIP14, HERMETIC SEALED, DIP-14, Operational Amplifier
ADI
OP207AY/883
IC DUAL OP-AMP, 230 uV OFFSET-MAX, 0.6 MHz BAND WIDTH, CDIP14, HERMETIC SEALED, DIP-14, Operational Amplifier
ADI
OP207AY/883C
IC DUAL OP-AMP, 230 uV OFFSET-MAX, 0.6 MHz BAND WIDTH, CDIP14, HERMETIC SEALED, DIP-14, Operational Amplifier
ADI
©2020 ICPDF网 联系我们和版权申明