AT25640B-MAHL-T [ATMEL]
serial electrically-erasable programmable read-only memory; 串行电可擦除可编程只读存储器型号: | AT25640B-MAHL-T |
厂家: | ATMEL |
描述: | serial electrically-erasable programmable read-only memory |
文件: | 总26页 (文件大小:1248K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Features
• Serial Peripheral Interface (SPI) Compatible
• Supports SPI Modes 0 (0,0) and 3 (1,1)
– Datasheet Describes Mode 0 Operation
• Low-voltage and Standard-voltage Operation
– 1.8 (VCC = 1.8V to 5.5V)
• 20MHz Clock Rate (5V)
• 32-byte Page Mode
• Block Write Protection
SPI Serial
EEPROMs
32K (4096 x 8)
64K (8192 x 8)
– Protect 1/4, 1/2, or Entire Array
• Write Protect (WP) Pin and Write Disable Instructions for Both Hardware and Software
Data Protection
• Self-timed Write Cycle (5ms max)
• High Reliability
– Endurance: One Million Write Cycles
– Data Retention: 100 Years
• Green (Pb/Halide-free/RoHS Compliant) Packaging Options
• Die Sales: Wafer Form, Tape and Reel, and Bumped Wafers
Atmel
Description
AT25320B
AT25640B
The Atmel® AT25320B/640B provides 32768-/65536-bits of serial electrically-erasable
programmable read-only memory (EEPROM) organized as 4096/8192 words of 8-bits
each. The device is optimized for use in many industrial and commercial applications
where low-power and low-voltage operation are essential. The AT25320B/640B is
available in space-saving 8-lead JEDEC SOIC, 8-lead UDFN, 8-lead XDFN, 8-lead
TSSOP, and 8-ball VFBGA packages.
The AT25320B/640B is enabled through the Chip Select pin (CS) and accessed via a
three-wire interface consisting of Serial Data Input (SI), Serial Data Output (SO), and
Serial Clock (SCK). All programming cycles are completely self-timed, and no sepa-
rate erase cycle is required before write.
Table 0-1.
Pin Configuration
8-lead SOIC
8-lead TSSOP
Pin Name Function
CS
SO
VCC
CS
SO
1
2
3
4
8
7
6
5
VCC
1
2
3
4
8
7
6
5
HOLD
SCK
SI
HOLD
SCK
SI
CS
Chip Select
WP
WP
SCK
SI
Serial Data Clock
Serial Data Input
Serial Data Output
Ground
GND
GND
8-lead UDFN
8-lead XDFN
SO
8
7
6
5
1
2
3
4
8
7
6
5
1
2
3
4
VCC
CS
SO
VCC
CS
GND
VCC
WP
HOLD
SCK
SI
HOLD
SCK
SI
SO
Power Supply
Write Protect
WP
WP
GND
GND
Bottom View
Bottom View
HOLD
Suspends Serial Input
8-ball VFBGA
VCC
8
7
6
5
1
2
3
4
CS
SO
HOLD
SCK
SI
WP
GND
8535F–SEEPR–6/10
Bottom View
Block write protection is enabled by programming the status register with one of four blocks of write protection.
Separate program enable and program disable instructions are provided for additional data protection. Hardware
data protection is provided via the WP pin to protect against inadvertent write attempts to the status register. The
HOLD pin may be used to suspend any serial communication without resetting the serial sequence.
1.
Absolute Maximum Ratings*
*NOTICE:
Stresses beyond those listed under “Abso-
lute Maximum Ratings” may cause perma-
nent damage to the device. This is a stress
rating only and functional operation of the
device at these or any other conditions
beyond those indicated in the operational
sections of this specification is not implied.
Exposure to absolute maximum rating con-
ditions for extended periods may affect
device reliability.
Operating Temperature............................–55C to +125C
Storage Temperature ...............................–65C to +150C
Voltage on Any Pin
with Respect to Ground..............................–1.0V to +7.0V
Maximum Operating Voltage.................................... 6.25V
DC Output Current ................................................. 5.0 mA
Figure 1-1. Block Diagram
2
Atmel AT25320B/640B
8535F–SEEPR–6/10
Atmel AT25320B/640B
Table 1-1.
Applicable over recommended operating range from TA = 25°C, f = 1.0MHz, VCC = +5.0V (unless otherwise noted)
Pin Capacitance(1)
Symbol
COUT
CIN
Test Conditions
Max
8
Units
pF
Conditions
VOUT = 0V
VIN = 0V
Output Capacitance (SO)
Input Capacitance (CS, SCK, SI, WP, HOLD)
6
pF
Note:
1. This parameter is characterized and is not 100% tested
Table 1-2.
DC Characteristics
Applicable over recommended operating range from: TAI = –40°C to +85C, VCC = +1.8V to +5.5V (unless otherwise noted)
Symbol
VCC1
Parameter
Test Condition
Min
1.8
2.5
4.5
Typ
Max
5.5
Units
V
Supply Voltage
Supply Voltage
Supply Voltage
Supply Current
VCC2
5.5
V
VCC3
5.5
V
ICC1
VCC = 5.0V at 20MHz, SO = Open, Read
7.5
4.0
10.0
mA
VCC = 5.0V at 20MHz, SO = Open, Read,
Write
ICC2
ICC3
Supply Current
Supply Current
10.0
mA
mA
VCC = 5.0V at 5MHz, SO = Open,
Read, Write
4.0
6.0
ISB1
ISB2
ISB3
IIL
Standby Current
Standby Current
Standby Current
Input Leakage
VCC = 1.8V, CS = VCC
VCC = 2.5V, CS = VCC
VCC = 5.0V, CS = VCC
VIN = 0V to VCC
< 0.1
0.3
6.0(2)
7.0(2)
µA
µA
µA
µA
µA
V
2.0
10.0(2)
–3.0
–3.0
3.0
IOL
Output Leakage
VIN = 0V to VCC, TAC = 0°C to 70°C
3.0
(1)
VIL
Input Low-voltage
Input High-voltage
Output Low-voltage
Output High-voltage
Output Low-voltage
Output High-voltage
–0.6
VCC x 0.3
VCC + 0.5
0.4
(1)
VIH
VCC x 0.7
V
VOL1
VOH1
VOL2
VOH2
IOL = 3.0mA
3.6V VCC 5.5V
V
IOH = 1.6mA
VCC - 0.8
VCC - 0.2
V
IOL = 0.15mA
1.8V VCC 3.6V
0.2
V
IOH = 100µA
V
Notes: 1. VIL min and VIH max are reference only and are not tested
2. Worst case measured at 85°C
3
8535F–SEEPR–6/10
Table 1-3.
AC Characteristics
Applicable over recommended operating range from TAI = –40°C to +85°C, VCC = As Specified,
CL = 1 TTL Gate and 30pF (unless otherwise noted)
Symbol
Parameter
Voltage
Min
Max
Units
4.5–5.5
2.5–5.5
1.8–5.5
0
0
0
20
10
5
fSCK
SCK Clock Frequency
MHz
4.5–5.5
2.5–5.5
1.8–5.5
2
2
2
tRI
Input Rise Time
Input Fall Time
SCK High Time
µs
µs
ns
4.5–5.5
2.5–5.5
1.8–5.5
2
2
2
tFI
20
40
4.5–5.5
2.5–5.5
1.8–5.5
tWH
80
20
40
4.5–5.5
2.5–5.5
1.8–5.5
tWL
tCS
tCSS
tCSH
tSU
tH
SCK Low Time
CS High Time
ns
ns
ns
ns
ns
ns
80
4.5–5.5
2.5–5.5
1.8–5.5
25
50
100
4.5–5.5
2.5–5.5
1.8–5.5
25
50
100
CS Setup Time
CS Hold Time
4.5–5.5
2.5–5.5
1.8–5.5
25
50
100
4.5–5.5
2.5–5.5
1.8–5.5
5
10
20
Data In Setup Time
Data In Hold Time
HOLD Setup Time
HOLD Hold Time
Output Valid
4.5–5.5
2.5–5.5
1.8–5.5
5
10
20
4.5–5.5
2.5–5.5
1.8–5.5
5
10
20
tHD
tCD
tV
4.5–5.5
2.5–5.5
1.8–5.5
5
10
20
ns
ns
ns
20
40
4.5–5.5
2.5–5.5
1.8–5.5
0
0
0
80
4.5–5.5
2.5–5.5
1.8–5.5
0
0
0
tHO
Output Hold Time
4
Atmel AT25320B/640B
8535F–SEEPR–6/10
Atmel AT25320B/640B
Table 1-3.
AC Characteristics (Continued)
Applicable over recommended operating range from TAI = –40°C to +85°C, VCC = As Specified,
CL = 1 TTL Gate and 30pF (unless otherwise noted)
Symbol
Parameter
Voltage
Min
Max
Units
4.5–5.5
2.5–5.5
1.8–5.5
0
0
0
25
50
100
tLZ
HOLD to Output Low Z
ns
4.5–5.5
2.5–5.5
1.8–5.5
40
80
200
tHZ
HOLD to Output High Z
Output Disable Time
ns
ns
4.5–5.5
2.5–5.5
1.8–5.5
40
80
200
tDIS
4.5–5.5
2.5–5.5
1.8–5.5
5
5
5
tWC
Write Cycle Time
ms
Endurance(1)
3.3V, 25°C, Page Mode
1M
Write Cycles
Note:
1. This parameter is characterized and is not 100% tested
2.
Serial Interface Description
MASTER: The device that generates the serial clock.
SLAVE: Because the Serial Clock pin (SCK) is always an input, the Atmel® AT25320B/640B always operates as a
slave.
TRANSMITTER/RECEIVER: The AT25320B/640B has separate pins designated for data transmission (SO) and
reception (SI).
MSB: The Most Significant Bit (MSB) is the first bit transmitted and received.
SERIAL OP-CODE: After the device is selected with CS going low, the first byte will be received. This byte con-
tains the op-code that defines the operations to be performed.
INVALID OP-CODE: If an invalid op-code is received, no data will be shifted into the AT25320B/640B, and the
serial output pin (SO) will remain in a high impedance state until the falling edge of CS is detected again. This will
reinitialize the serial communication.
CHIP SELECT: The AT25320B/640B is selected when the CS pin is low. When the device is not selected, data will
not be accepted via the SI pin, and the serial output pin (SO) will remain in a high impedance state.
HOLD: The HOLD pin is used in conjunction with the CS pin to select the AT25320B/640B. When the device is
selected and a serial sequence is underway, HOLD can be used to pause the serial communication with the mas-
ter device without resetting the serial sequence. To pause, the HOLD pin must be brought low while the SCK pin is
low. To resume serial communication, the HOLD pin is brought high while the SCK pin is low (SCK may still toggle
during HOLD). Inputs to the SI pin will be ignored while the SO pin is in the high impedance state.
WRITE PROTECT: The write protect pin (WP) will allow normal read/write operations when held high. When the
WP pin is brought low and WPEN bit is “1”, all write operations to the status register are inhibited. WP going low
while CS is still low will interrupt a write to the status register. If the internal write cycle has already been initiated,
WP going low will have no effect on any write operation to the status register. The WP pin function is blocked when
the WPEN bit in the status register is “0”. This will allow the user to install the AT25320B/640B in a system with the
5
8535F–SEEPR–6/10
WP pin tied to ground and still be able to write to the status register. All WP pin functions are enabled when the
WPEN bit is set to “1”.
Figure 2-1. SPI Serial Interface
AT25320B/640B
6
Atmel AT25320B/640B
8535F–SEEPR–6/10
Atmel AT25320B/640B
3.
Functional Description
The Atmel® AT25320B/640B is designed to interface directly with the synchronous serial peripheral interface (SPI)
of the 6805 and 68HC11 series of microcontrollers.
The AT25320B/640B utilizes an 8-bit instruction register. The list of instructions and their operation codes are con-
tained in Table 3-1. All instructions, addresses, and data are transferred with the MSB first and start with a high-to-
low CS transition.
Table 3-1.
Instruction Set for the Atmel AT25320B/640B
Instruction Name
WREN
Instruction Format
0000 X110
Operation
Set Write Enable Latch
Reset Write Enable Latch
Read Status Register
Write Status Register
Read Data from Memory Array
Write Data to Memory Array
WRDI
0000 X100
RDSR
0000 X101
WRSR
0000 X001
READ
0000 X011
WRITE
0000 X010
WRITE ENABLE (WREN): The device will power up in the write disable state when VCC is applied. All program-
ming instructions must therefore be preceded by a Write Enable instruction.
WRITE DISABLE (WRDI): To protect the device against inadvertent writes, the Write Disable instruction disables
all programming modes. The WRDI instruction is independent of the status of the WP pin.
READ STATUS REGISTER (RDSR): The Read Status Register instruction provides access to the status register.
The READY/BUSY and Write Enable status of the device can be determined by the RDSR instruction. Similarly,
the Block Write Protection Bits indicate the extent of protection employed. These bits are set by using the WRSR
instruction.
Table 3-2.
Status Register Format
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
WPEN
X
X
X
BP1
BP0
WEN
RDY
Table 3-3.
Bit
Read Status Register Bit Definition
Definition
Bit 0 = “0” (RDY) indicates the device is READY. Bit 0 = “1” indicates the write cycle
is in progress.
Bit 0 (RDY)
Bit 1 (WEN)
Bit 1= “0” indicates the device is not WRITE ENABLED. Bit 1 = “1” indicates the
device is write enabled.
Bit 2 (BP0)
Bit 3 (BP1)
See Table 3-4 on page 8.
See Table 3-4 on page 8.
Bits 4–6 are “0”s when device is not in an internal write cycle.
Bit 7 (WPEN) See Table 3-5 on page 8.
Bits 0–7 are “1”s during an internal write cycle.
7
8535F–SEEPR–6/10
WRITE STATUS REGISTER (WRSR): The WRSR instruction allows the user to select one of four levels of protec-
tion. The Atmel® AT25320B/640B is divided into four array segments. One-quarter, one-half, or all of the memory
segments can be protected. Any of the data within any selected segment will therefore be read only. The block
write protection levels and corresponding status register control bits are shown in Table 3-4 on page 8.
The three bits BP0, BP1, and WPEN are nonvolatile cells that have the same properties and functions as the regu-
lar memory cells (e.g., WREN, tWC, RDSR).
Table 3-4.
Block Write Protect Bits
Status Register Bits
Array Addresses Protected
Atmel AT25320B Atmel AT25640B
None None
Level
0
BP1
BP0
0
0
1
1
0
1
0
1
1(1/4)
2(1/2)
3(All)
0C000FFF
08000FFF
00000FFF
18001FFF
10001FFF
00001FFF
The WRSR instruction also allows the user to enable or disable the write protect (WP) pin through the use of the
Write Protect Enable (WPEN) bit. Hardware write protection is enabled when the WP pin is low and the WPEN bit
is “1”. Hardware write protection is disabled when either the WP pin is high or the WPEN bit is “0”. When the device
is hardware write protected, writes to the status register, including the block protect bits and the WPEN bit, and the
block-protected sections in the memory array are disabled. Writes are only allowed to sections of the memory that
are not block-protected.
Note:
When the WPEN bit is hardware write protected, it cannot be changed back to “0” as long as the WP pin is held low.
Table 3-5.
WPEN Operation
Protected
Blocks
Unprotected
Blocks
Status
Register
WPEN
WP
X
WEN
0
0
1
1
X
X
0
1
0
1
0
1
Protected
Protected
Protected
Protected
Protected
Protected
Protected
Writeable
Protected
Writeable
Protected
Writeable
Protected
Writeable
Protected
Protected
Protected
Writeable
X
Low
Low
High
High
READ SEQUENCE (READ): Reading the AT25320B/640B via the Serial Output (SO) pin requires the following
sequence. After the CS line is pulled low to select a device, the read op-code is transmitted via the SI line followed
by the byte address to be read (A15–A0, see Table 3-6). Upon completion, any data on the SI line will be ignored.
The data (D7–D0) at the specified address is then shifted out onto the SO line. If only one byte is to be read, the CS
line should be driven high after the data comes out. The read sequence can be continued since the byte address is
automatically incremented and data will continue to be shifted out. When the highest address is reached, the
address counter will roll over to the lowest address allowing the entire memory to be read in one continuous read
cycle.
8
Atmel AT25320B/640B
8535F–SEEPR–6/10
Atmel AT25320B/640B
WRITE SEQUENCE (WRITE): In order to program the Atmel® AT25320B/640B, two separate instructions must be
executed. First, the device must be write enabled via the WREN instruction. Then a write (WRITE) instruction
may be executed. Also, the address of the memory location(s) to be programmed must be outside the protected
address field location selected by the block write protection level. During an internal write cycle, all commands will
be ignored except the RDSR instruction.
A write instruction requires the following sequence. After the CS line is pulled low to select the device, the WRITE
op-code is transmitted via the SI line followed by the byte address (A15–A0) and the data (D7–D0) to be pro-
grammed (see Table 3-6). Programming will start after the CS pin is brought high. The low-to-high transition of the
CS pin must occur during the SCK low-time immediately after clocking in the D0 (LSB) data bit.
The READY/BUSY status of the device can be determined by initiating a read status register
(RDSR) instruction. If Bit 0 = “1”, the write cycle is still in progress. If Bit 0 = “0”, the write cycle has ended. Only the
RDSR instruction is enabled during the write programming cycle.
The AT25320B/640B is capable of a 32-byte page write operation. After each byte of data is received, the five low-
order address bits are internally incremented by one; the high-order bits of the address will remain constant. If
more than 32-bytes of data are transmitted, the address counter will roll over and the previously written data will be
overwritten. The AT25320B/640B is automatically returned to the write disable state at the completion of a write
cycle.
Note:
If the device is not write-enabled (WREN), the device will ignore the write instruction and will return to the standby
state, when CS is brought high. A new CS falling edge is required to reinitiate the serial communication.
Table 3-6.
Address Key
Address
AN
Don’t Care Bits
Atmel AT25320B
A11–A0
Atmel AT25640B
A12–A0
A15–A12
A15–A13
9
8535F–SEEPR–6/10
4.
Timing Diagrams
Figure 4-1. Synchronous Data Timing (for Mode 0)
tCS
VIH
CS
VIL
tCSH
tCSS
VIH
tWH
tWL
SCK
VIL
tSU
tH
VIH
VIL
VALID IN
SI
tHO
tDIS
tV
VOH
VOL
HI-Z
HI-Z
SO
Figure 4-2. WREN Timing
CS
SCK
SI
WREN OP-CODE
HI-Z
SO
Figure 4-3. WRDI Timing
CS
SCK
SI
WRDI OP-CODE
HI-Z
SO
10
Atmel AT25320B/640B
8535F–SEEPR–6/10
Atmel AT25320B/640B
Figure 4-4. RDSR Timing
CS
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
SCK
SI
INSTRUCTION
DATA OUT
HIGH IMPEDANCE
SO
7
6
5
4
3
2
1
0
MSB
Figure 4-5. WRSR Timing
CS
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
SCK
SI
DATA IN
INSTRUCTION
7
6
5
4
3
2
1
0
HIGH IMPEDANCE
SO
Figure 4-6. READ Timing
CS
0
1
2
3
4
5
6
7
8
9
10 11 20 21 22 23 24 25 26 27 28 29 30
SCK
SI
BYTE ADDRESS
...
INSTRUCTION
15 14 13
3
2
1
0
DATA OUT
HIGH IMPEDANCE
SO
7
6
5
4
3
2
1
0
MSB
11
8535F–SEEPR–6/10
Figure 4-7. WRITE Timing
CS
0
1
2
3
4
5
6
7
8
9 10 11 20 21 22 23 24 25 26 27 28 29 30 31
SCK
SI
BYTE ADDRESS
DATA IN
...
INSTRUCTION
15 14 13
3
2
1
0
7
6
5
4
3
2
1
0
HIGH IMPEDANCE
SO
Figure 4-8. HOLD Timing
CS
tCD
tCD
SCK
HOLD
SO
tHD
tHD
tHZ
tLZ
12
Atmel AT25320B/640B
8535F–SEEPR–6/10
Atmel AT25320B/640B
5.
Ordering Code Detail
A T 2 5 3 2 0 B - S S H L - B
Atmel Designator
Product Family
Device Density
Shipping Carrier Option
B or blank = Bulk (tubes)
T
=
Tape and reel
Operating Voltage
L
=
1.8V to 5.5V
320 = 32-kilobit
640 = 64-kilobit
Packaged Device Grade or
Wafer/Die Thickness
H
=
=
=
Green, NiPdAu lead finish
Industrial Temperature range
(-40°C to +85°C)
Green, matte Sn lead finish
Industrial Temperature range
(-40°C to +85°C)
Device Revision
U
11
11 mil wafer thickness
Package Option
SS
X
MA
ME
C
=
=
=
=
=
JEDEC SOIC
TSSOP
UDFN
XDFN
VFBGA
WWU = Wafer unsawn
WDT = Die in Tape and Reel
13
8535F–SEEPR–6/10
6.
Part Markings
6.1
Atmel AT25320B
AT25320B-SSHL
Top Mark
Seal Year
| Seal Week
| | |
@ = Country of Ass’y
Y = SEAL YEAR
WW = SEAL WEEK
02 = Week 2
04 = Week 4
:: : :::: :
:: : :::: ::
50 = Week 50
52 = Week 52
|---|---|---|---|---|---|---|---|
A T M L H Y W W
|---|---|---|---|---|---|---|---|
6:2006
7:2007
8:2008
9:2009
0: 2010
1: 2011
2: 2012
3: 2013
5 B B
L
@
|---|---|---|---|---|---|---|---|
* LOT NUMBER
|---|---|---|---|---|---|---|---|
|
PIN 1 INDICATOR (DOT)
AT25320B-XHL
Top Mark
PIN 1 INDICATOR (DOT)
@ = Country of Ass’y
Y = SEAL YEAR
|
WW = SEAL WEEK
02 = Week 2
04 = Week 4
:: : :::: :
:: : :::: ::
50 = Week 50
52 = Week 52
* |---|---|---|---|---|---|
A T H Y W W
|---|---|---|---|---|---|
8:2008
9:2009
0:2010
1:2011
2: 2012
3: 2013
4: 2014
5: 2015
5 B B L
@
|---|---|---|---|---|---|---|
ATMEL LOT NUMBER
|---|---|---|---|---|---|---|
AT25320B-MAHL
Top Mark
Y = YEAR OF ASSEMBLY
@ = Country of Ass’y
|---|---|---|
5 B B
|---|---|---|
H L @
|---|---|---|
Y X X
|---|---|---|
*
XX= ATMEL LOT NUMBER TO COORESPOND
WITH TRACE CODE LOG BOOK
(e.g. XX = AA, AB, AC,... AX, AY AZ)
Y = SEAL YEAR
6:2006
7:2007
8:2008
9:2009
0: 2010
1: 2011
2: 2012
3: 2013
|
PIN 1 INDICATOR (DOT)
14
Atmel AT25320B/640B
8535F–SEEPR–6/10
Atmel AT25320B/640B
AT25320B-MEHL
Top Mark
Y = YEAR OF ASSEMBLY
|---|---|---|
@ = Country of Ass’y
5 B B
|---|---|---|
H L @
XX= ATMEL LOT NUMBER TO COORESPOND
WITH TRACE CODE LOG BOOK
(e.g. XX = AA, AB, AC,... AX, AY AZ)
Y = SEAL YEAR
|---|---|---|
Y X X
6:2006
7:2007
8:2008
9:2009
0: 2010
1: 2011
2: 2012
3: 2013
|---|---|---|
*
|
PIN 1 INDICATOR (DOT)
AT25320B-CUL
Top Mark
|---|---|---|---|
5 B B U
B = Country of Origin
Y = One Digit Year Code
M = One Digit Month Code
|---|---|---|---|
B Y M X X
|---|---|---|---|---|
* <-- PIN 1 INDICATOR
XX= TRACE CODE (ATMEL LOT NUMBER TO
COORESPOND WITH TRACE CODE LOG BOOK)
(e.g. XX = AA, AB, AC,... YZ, ZZ)
M = SEAL MONTH
(USE ALPHA DESIGNATOR A-L)
Y = ONE DIGIT YEAR CODE
4:2004
5:2005
6:2006
7: 2007
8: 2008
9: 2009
A = JANUARY
B = FEBRUARY
" " """"""""
J = OCTOBER
K = NOVEMBER
L = DECEMBER
15
8535F–SEEPR–6/10
6.2
Atmel AT25640B
AT25640B-SSHL
Top Mark
Seal Year
| Seal Week
| | |
@ = Country of Ass’y
Y = SEAL YEAR
WW = SEAL WEEK
02 = Week 2
04 = Week 4
:: : :::: :
:: : :::: ::
50 = Week 50
52 = Week 52
|---|---|---|---|---|---|---|---|
A T M L H Y W W
|---|---|---|---|---|---|---|---|
6:2006
7:2007
8:2008
9:2009
0: 2010
1: 2011
2: 2012
3: 2013
5 C B
L
@
|---|---|---|---|---|---|---|---|
* LOT NUMBER
|---|---|---|---|---|---|---|---|
|
PIN 1 INDICATOR (DOT)
AT25640B-XHL
Top Mark
PIN 1 INDICATOR (DOT)
@ = Country of Ass’y
Y = SEAL YEAR
|
WW = SEAL WEEK
02 = Week 2
04 = Week 4
:: : :::: :
:: : :::: ::
50 = Week 50
52 = Week 52
* |---|---|---|---|---|---|
A T H Y W W
|---|---|---|---|---|---|
8:2008
9:2009
0:2010
1:2011
2: 2012
3: 2013
4: 2014
5: 2015
5 C B L
@
|---|---|---|---|---|---|---|
ATMEL LOT NUMBER
|---|---|---|---|---|---|---|
AT25640B-MAHL
Top Mark
Y = YEAR OF ASSEMBLY
@ = Country of Ass’y
|---|---|---|
5 C B
|---|---|---|
H L @
|---|---|---|
Y X X
|---|---|---|
*
XX= ATMEL LOT NUMBER TO COORESPOND
WITH TRACE CODE LOG BOOK
(e.g. XX = AA, AB, AC,... AX, AY AZ)
Y = SEAL YEAR
6:2006
7:2007
8:2008
9:2009
0: 2010
1: 2011
2: 2012
3: 2013
|
PIN 1 INDICATOR (DOT)
16
Atmel AT25320B/640B
8535F–SEEPR–6/10
Atmel AT25320B/640B
AT25640B-MEHL
Top Mark
Y = YEAR OF ASSEMBLY
|---|---|---|
XX= ATMEL LOT NUMBER TO COORESPOND
WITH TRACE CODE LOG BOOK
5 C B
|---|---|---|
(e.g. XX = AA, AB, AC,... AX, AY AZ)
Y = SEAL YEAR
Y X X
|---|---|---|
6:2006
7:2007
8:2008
9:2009
0: 2010
1: 2011
2: 2012
3: 2013
*
|
PIN 1 INDICATOR (DOT)
AT25640B-CUL
Top Mark
|---|---|---|---|
5 C B U
B = Country of Origin
Y = One Digit Year Code
M = One Digit Month Code
|---|---|---|---|
B Y M X X
|---|---|---|---|---|
* <-- PIN 1 INDICATOR
XX= TRACE CODE (ATMEL LOT NUMBER TO
COORESPOND WITH TRACE CODE LOG BOOK)
(e.g. XX = AA, AB, AC,... YZ, ZZ)
M = SEAL MONTH
(USE ALPHA DESIGNATOR A-L)
Y = ONE DIGIT YEAR CODE
4:2004
5:2005
6:2006
7: 2007
8: 2008
9: 2009
A = JANUARY
B = FEBRUARY
" " """"""""
J = OCTOBER
K = NOVEMBER
L = DECEMBER
17
8535F–SEEPR–6/10
7.
Ordering Codes
Atmel AT25320B Ordering Information
Ordering Code
Voltage
Package
Operation Range
AT25320B-SSHL-B(1) (NiPdAu Lead Finish)
AT25320B-SSHL-T(2) (NiPdAu Lead Finish)
AT25320B-XHL-B(1) (NiPdAu Lead Finish)
AT25320B-XHL-T(2) (NiPdAu Lead Finish)
AT25320B-MAHL-T(2) (NiPdAu Lead Finish)
AT25320B-MEHL-T(2) (NiPdAu Lead Finish)
AT25320B-CUL-T(2) (SnAgCu Ball Finish)
1.8V to 5.5V
1.8V to 5.5V
1.8V to 5.5V
1.8V to 5.5V
1.8V to 5.5V
1.8V to 5.5V
1.8V to 5.5V
8S1
8S1
8A2
Lead-free/Halogen-free/
Industrial Temperature
8A2
(40 to 85C)
8MA2
8ME1
8U2-1
Industrial Temperature
AT25320B-WWU11L(3)
1.8V to 5.5V
Die Sale
(40 to 85C)
Note:
1. Bulk delivery in tubes (SOIC and TSSOP 100/tube)
2. Tape and reel delivery (SOIC 4k/reel. TSSOP, UDFN, XDFN and VFBGA 5k/reel)
3. Contact Atmel Sales for Wafer sales
Package Type
8S1
8A2
8-lead, 0.150” Wide, Plastic Gull Wing Small Outline (JEDEC SOIC)
8-lead, 4.4mm Body, Plastic Thin Shrink Small Outline Package (TSSOP)
8MA2
8-lead, 2.00mm x 3.00mm Body, 0.50mm Pitch, Ultra Thin, Dual No Lead Package (UDFN)
8-lead (1.8mm x 2.2mm Body) Ultra Leadframe Land Grid Array (XDFN)
8ME1
8U2-1
8-lead, 8.35mm x 3.73mm Body, 0.75mm Pitch, VFBGA Package (VFBGA)
18
Atmel AT25320B/640B
8535F–SEEPR–6/10
Atmel AT25320B/640B
Atmel AT25640B Ordering Information
Ordering Code
Voltage
Package
Operation Range
AT25640B-SSHL-B(1) (NiPdAu Lead Finish)
AT25640B-SSHL-T(2) (NiPdAu Lead Finish)
AT25640B-XHL-B(1) (NiPdAu Lead Finish)
AT25640B-XHL-T(2) (NiPdAu Lead Finish)
AT25640B-MAHL-T(2) (NiPdAu Lead Finish)
AT25640B-MEHL-T(2) (NiPdAu Lead Finish)
AT25640B-CUL-T(2) (SnAgCu Ball Finish)
1.8V to 5.5V
1.8V to 5.5V
1.8V to 5.5V
1.8V to 5.5V
1.8V to 5.5V
1.8V to 5.5V
1.8V to 5.5V
8S1
8S1
8A2
Lead-free/Halogen-free/
Industrial Temperature
8A2
(40 to 85C)
8MA2
8ME1
8U2-1
Industrial Temperature
AT25640B-WWU11L(3)
1.8V to 5.5V
Die Sale
(40 to 85C)
Note:
1. Bulk delivery in tubes (SOIC and TSSOP 100/tube)
2. Tape and reel delivery (SOIC 4k/reel. TSSOP, UDFN, XDFN and VFBGA 5k/reel)
3. Contact Atmel Sales for Wafer sales
Package Type
8S1
8A2
8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC)
8-lead, 4.4mm Body, Plastic Thin Shrink Small Outline Package (TSSOP)
8-lead, 2.00mm x 3.00mm Body, 0.50mm Pitch, Ultra Thin Mini-MAP, Dual No Lead Package (UDFN), (MLP
2x3mm)
8MA2
8ME1
8U2-1
8-lead (1.8mm x 2.2mm Body) Ultra Leadframe Land Grid Array (XDFN)
8-lead, 8.35mm x 3.73mm Body, 0.75mm Pitch, VFBGA Package (VFBGA)
19
8535F–SEEPR–6/10
8.
Packaging Information
8S1 – JEDEC SOIC
C
1
E
E1
L
N
Ø
TOP VIIEWW
END VIEW
e
b
A
COMMON DIMENSIONS
(Unit of Measure = mm)
MIN
1.35
0.10
MAX
1.75
0.25
NOM
NOTE
SYMBOL
A1
A
–
–
A1
b
0.31
0.17
4.80
3.81
5.79
–
0.51
0.25
5.05
3.99
6.20
C
D
E1
E
e
–
D
–
–
–
SIDE VIEW
1.27 BSC
Notes: This drawing is for general information only.
Refer to JEDEC Drawing MS-012, Variation AA
for proper dimensions, tolerances, datums, etc.
L
0.40
0°
–
–
1.27
8°
Ø
5/19/10
TITLE
GPC
DRAWING NO.
REV.
Package Drawing Contact:
packagedrawings@atmel.com
8S1, 8-lead (0.150”Wide Body), Plastic Gull
Wing Small Outline (JEDEC SOIC)
SWB
8S1
F
20
Atmel AT25320B/640B
8535F–SEEPR–6/10
Atmel AT25320B/640B
8A2 – TSSOP
3
2 1
Pin 1 indicator
this corner
E1
E
L1
N
L
Top View
End View
COMMON DIMENSIONS
(Unit of Measure = mm)
MIN
MAX
NOM
3.00
NOTE
SYMBOL
D
2.90
3.10
2, 5
A
E
6.40 BSC
4.40
b
E1
A
4.30
–
4.50
1.20
1.05
0.30
3, 5
4
–
A2
b
0.80
0.19
1.00
e
A2
–
D
e
0.65 BSC
0.60
L
0.45
0.75
Side View
L1
1.00 REF
Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions,
tolerances, datums, etc.
2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall
not exceed 0.15 mm (0.006 in) per side.
3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed
0.25 mm (0.010 in) per side.
4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess
of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot.
Minimum space between protrusion and adjacent lead is 0.07 mm.
5. Dimension D and E1 to be determined at Datum Plane H.
5/19/10
TITLE
GPC
TNR
DRAWING NO.
REV.
Package Drawing Contact:
packagedrawings@atmel.com
8A2, 8-lead 4.4mm Body, Plastic Thin
Shrink Small Outline Package (TSSOP)
8A2
E
21
8535F–SEEPR–6/10
8MA2 - UDFN
E
1
2
3
4
8
7
6
5
Pin 1 ID
D
C
A2
A1
A
E2
b (8x)
8
7
6
1
2
3
4
COMMON DIMENSIONS
(Unit of Measure = mm)
Pin#1 ID
(R0.10)
0.35
D2
SYMBOL
MIN
NOM
2.00 BSC
3.00 BSC
1.50
MAX
NOTE
D
E
5
1.60
1.40
0.60
0.05
0.55
D2
E2
A
1.40
1.20
0.50
0.00
–
e (6x)
1.30
L (8x)
K
0.55
A1
A2
C
0.02
Notes: 1. This drawing is for general information only. Refer to
JEDEC Drawing MO-229 for proper dimensions,
tolerances, datums, etc.
–
0.152 REF
0.35
2. The terminal #1 ID is a laser-marked feature.
3. Dimensions b applies to metalized terminal and is
measured between 0.15 mm and 0.30 mm from the
terminal tip. If the terminal has the optional radius on
the other end of the terminal, the dimension should not
be measured in that radius area.
0.40
L
0.30
e
0.50 BSC
0.25
0.30
–
3
b
0.18
0.20
K
–
4/15/08
TITLE
GPC
DRAWING NO.
REV.
Package Drawing Contact:
packagedrawings@atmel.com
8MA2, 8-pad, 2 x 3 x 0.6 mm Body, Thermally
Enhanced Plastic Ultra Thin Dual Flat No
Lead Package (UDFN)
YNZ
8MA2
A
22
Atmel AT25320B/640B
8535F–SEEPR–6/10
Atmel AT25320B/640B
8ME1 - XDFN
e1
D
b
8
7
6
5
L
E
PIN #1 ID
0.10
PIN #1 ID
0.15
1
2
3
4
A1
b
e
A
Top View
Side View
Bottom View
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL
MIN
–
NOM
–
MAX
0.40
0.05
1.90
2.30
0.25
NOTE
A
A1
D
E
0.00
1.70
2.10
0.15
–
1.80
2.20
b
0.20
e
0.40 TYP
1.20 REF
0.30
e1
L
0.35
0.26
8/3/09
TITLE
GPC
DRAWING NO.
REV.
8ME1, 8-lead (1.80 x 2.20 mm Body)
Extra Thin DFN (XDFN)
Package Drawing Contact:
packagedrawings@atmel.com
DTP
8ME1
A
23
8535F–SEEPR–6/10
8U2-1 - VFBGA
// 0.10 C
(4X)
0.10
A
0.08 C
C
D
A1 Ball Pad Corner
Øb
M
M
Ø0.15
Ø0.08
C A B
C
e
A1
B
A2
A
Top View
Side View
A1 BALL PAD CORNER
2
1
A
B
C
D
COMMON DIMENSIONS
(Unit of Measure = mm)
e
SYMBOL
MIN
0.81
0.15
0.40
0.25
NOM
0.91
MAX
NOTE
(e1)
1.00
0.25
0.50
0.35
A
A1
A2
b
0.20
d
0.45
(d1)
0.30
D
2.35 BSC
3.73 BSC
0.75 BSC
0.74 BSC
0.75 BSC
0.80 REF
Bottom View
8 SOLDER BALLS
E
e
Notes: 1. This drawing is for general information.
e1
d
2. Dimension 'b' is measured at the maximum solder
ball diameter.
3. Solder ball composition shall be 95.5Sn-4.0Ag-.5Cu.
d1
2/25/08
TITLE
GPC
DRAWING NO.
REV.
8U2-1, 8 ball, 2.35 x 3.73 mm Body,
0.75 mm pitch, VFBGA Package (dBGA2)
Package Drawing Contact:
packagedrawings@atmel.com
GWW
8U2-1
C
24
Atmel AT25320B/640B
8535F–SEEPR–6/10
Atmel AT25320B/640B
9.
Revision History
Doc. Rev.
8535F
Date
Comments
Update 8A2 and 8S1 package drawings
Remove Preliminary
6/2010
4/2010
8/2009
8535E
Update Ordering Code Detail, Ordering Information, template
Change Catalog Numbering
8535D
Add new Part Marking Information
8535C
8535B
8535A
5/2009
7/2008
4/2008
Add Part Marking information; changed to Preliminary status.
Modify ‘Endurance’ parameter on page 6.
Initial document release.
25
8535F–SEEPR–6/10
Headquarters
International
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131
USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Atmel Asia
Atmel Europe
Atmel Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
JAPAN
Tel: (+81) 3-3523-3551
Fax: (+81) 3-3523-7581
Unit 1-5 & 16, 19/F
BEA Tower, Millennium City 5
418 Kwun Tong Road
Kwun Tong, Kowloon
HONG KONG
Atmel Munich GmbH
Business Campus, Parkring 4
D-85748 Garching bei Munich
GERMANY
Tel: (+49) 89-31970-0
Fax: (+49) 89-31946-21
Tel: (+852) 2245-6100
Fax: (+852) 2722-1369
Product Contact
Web Site
Technical Support
Sales Contact
www.atmel.com
s_eeprom@atmel.com
www.atmel.com/contacts
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI-
TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN-
TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF
THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life.
© 2010 Atmel Corporation. All rights reserved.
Atmel®, Atmel logo and combinations thereof, and others, are registered trademarks or trademarks of Atmel Corporation or its subsidiaries.
Other terms and product names may be trademarks of others.
8535F–SEEPR–6/10
相关型号:
AT25640B-PU
EEPROM, 4KX8, Serial, CMOS, PDIP8, 0.300 INCH, HALOGEN FREE AND LEAD FREE, PLASTIC, MS-001BA, DIP-8
ATMEL
©2020 ICPDF网 联系我们和版权申明