T5753-6APJ [ATMEL]
UHF ASK/FSK Transmitter; 超高频ASK / FSK发射器
| 型号： | T5753-6APJ |
| 厂家： | 
ATMEL |
| 描述： | UHF ASK/FSK Transmitter |
| 文件： | 总13页 (文件大小：193K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Features
• Integrated PLL Loop Filter
• ESD Protection also at ANT1/ANT2
(4 kV HBM/200 V MM; Except Pin 2: 4 kV HBM/100 V MM)
• High Output Power (8.0 dBm) with Low Supply Current (9.0 mA)
• Modulation Scheme ASK/FSK
– FSK Modulation is Achieved by Connecting an Additional Capacitor Between the
XTAL Load Capacitor and the Open Drain Output of the Modulating Microcontroller
• Easy to Design-in Due to Excellent Isolation of the PLL from the PA and Power Supply
• Single Li-cell for Power Supply
• Supply Voltage 2.0V to 4.0V in the Temperature Range of –40°C to +85°C/125°C
• Package TSSOP8L
UHF ASK/FSK
Transmitter
• Single-ended Antenna Output with High Efficient Power Amplifier
• CLK Output for Clocking the Microcontroller
• One-chip Solution with Minimum External Circuitry
• 125°C Operation for Tire Pressure Systems
T5753
1. Description
The T5753 is a PLL transmitter IC which has been developed for the demands of RF
low-cost transmission systems at data rates up to 32 kBaud. The transmitting
frequency range is 310 MHz to 350 MHz. It can be used in both FSK and ASK
systems.
Figure 1-1. System Block Diagram
UHF ASK/FSK
UHF ASK/FSK
Remote control transmitter
Remote control receiver
1 Li cell
T5753
U3741B/
U3745B/
T5743/
1 to 3 Micro-
controller
Demod
IF Amp
Control
T5744
Encoder
ATARx9x
PLL
Keys
Antenna Antenna
XTO
VCO
LNA
PLL
XTO
LNA
VCO
4510I–RKE–02/07
2. Pin Configuration
Figure 2-1. Pinning TSSOP8L
T5753
CLK
PA_ENABLE
ANT2
1
2
3
4
8
7
6
5
ENABLE
GND
VS
ANT1
XTAL
Table 2-1.
Pin
Pin Description
Symbol
Function
Configuration
VS
Clock output signal for microcontroller
The clock output frequency is set by the
crystal to fXTAL/4
100Ω
CLK
1
CLK
100Ω
50 kΩ
PA_ENABLE
UREF = 1.1V
Switches on power amplifier, used for
ASK modulation
2
PA_ENABLE
20 µA
ANT1
ANT2
3
4
ANT2
ANT1
Emitter of antenna output stage
Open collector antenna output
2
T5753
4510I–RKE–02/07
T5753
Table 2-1.
Pin
Pin Description (Continued)
Symbol
Function
Configuration
VS
VS
1.5 kΩ
1.2 kΩ
5
XTAL
Connection for crystal
XTAL
182 µA
6
7
VS
Supply voltage
Ground
See ESD protection circuitry (see Figure 4-5 on page 9)
See ESD protection circuitry (see Figure 4-5 on page 9)
GND
200 kΩ
ENABLE
8
ENABLE
Enable input
Figure 2-2. Block Diagram
T5753
Power up/down
f
CLK
PA_ENABLE
ANT2
ENABLE
4
1
8
7
f
32
GND
2
PDF
CP
VS
3
4
6
5
LF
ANT1
PA
VCO
XTO
XTAL
PLL
3
4510I–RKE–02/07
3. General Description
This fully integrated PLL transmitter allows particularly simple, low-cost RF miniature transmit-
ters to be assembled. The VCO is locked to 32 fXTAL hence a 9.8438 MHz crystal is needed for a
315 MHz transmitter. All other PLL and VCO peripheral elements are integrated.
The XTO is a series resonance oscillator so that only one capacitor together with a crystal con-
nected in series to GND are needed as external elements.
The crystal oscillator together with the PLL needs typically < 3 ms until the PLL is locked and the
CLK output is stable. There is a wait time of ≥ 3 ms until the CLK is used for the microcontroller
and the PA is switched on.
The power amplifier is an open-collector output delivering a current pulse which is nearly inde-
pendent from the load impedance. The delivered output power is hence controllable via the
connected load impedance.
This output configuration enables a simple matching to any kind of antenna or to 50 Ω. A high
power efficiency of η= Pout/(IS,PA VS) of 40% for the power amplifier results when an optimized
load impedance of ZLoad = (255 + j192) Ω is used at 3 V supply voltage.
4. Functional Description
If ENABLE = L and the PA_ENABLE = L, the circuit is in standby mode consuming only a very
small amount of current so that a lithium cell used as power supply can work for several years.
With ENABLE = H the XTO, PLL and the CLK driver are switched on. If PA_ENABLE remains L
only the PLL and the XTO is running and the CLK signal is delivered to the microcontroller. The
VCO locks to 32 times the XTO frequency.
With ENABLE = H and PA_ENABLE = H the PLL, XTO, CLK driver and the power amplifier are
on. With PA_ENABLE the power amplifier can be switched on and off, which is used to perform
the ASK modulation.
4.1
4.2
ASK Transmission
The T5753 is activated by ENABLE = H. PA_ENABLE must remain L for typically ≥ 3 ms, then
the CLK signal can be taken to clock the microcontroller and the output power can be modulated
by means of Pin PA_ENABLE. After transmission PA_ENABLE is switched to L and the micro-
controller switches back to internal clocking. The T5753 is switched back to standby mode with
ENABLE = L.
FSK Transmission
The T5753 is activated by ENABLE = H. PA_ENABLE must remain L for typically ≥ 3 ms, then
the CLK signal can be taken to clock the microcontroller and the power amplifier is switched on
with PA_ENABLE = H. The chip is then ready for FSK modulation. The microcontroller starts to
switch on and off the capacitor between the XTAL load capacitor and GND with an open-drain
output port, thus changing the reference frequency of the PLL. If the switch is closed, the output
frequency is lower than if the switch is open. After transmission PA_ENABLE is switched to L
and the microcontroller switches back to internal clocking. The T5753 is switched back to
standby mode with ENABLE = L.
The accuracy of the frequency deviation with XTAL pulling method is about ±25% when the fol-
lowing tolerances are considered.
4
T5753
4510I–RKE–02/07
T5753
Figure 4-1. Tolerances of Frequency Modulation
VS
CStray1
CStray2
LM
C4
XTAL
CM
RS
C0
Crystal equivalent circuit
C5
CSwitch
Using C4 = 8.2 pF ±5%, C5 = 10 pF ±5%, a switch port with CSwitch = 3 pF ±10%, stray capaci-
tances on each side of the crystal of CStray1 = CStray2 = 1 pF ±10%, a parallel capacitance of the
crystal of C0 = 3.2 pF ±10% and a crystal with CM = 13 fF ±10%, an FSK deviation of ±21.5 kHz
typical with worst case tolerances of ±16.25 kHz to ±28.01 kHz results.
4.3
CLK Output
An output CLK signal is provided for a connected microcontroller, the delivered signal is CMOS
compatible if the load capacitance is lower than 10 pF.
4.3.1
Clock Pulse Take-over
The clock of the crystal oscillator can be used for clocking the microcontroller. Atmel®’s
ATARx9x has the special feature of starting with an integrated RC-oscillator to switch on the
T5753 with ENABLE = H, and after 1 ms to assume the clock signal of the transmission IC, so
that the message can be sent with crystal accuracy.
4.3.2
Output Matching and Power Setting
The output power is set by the load impedance of the antenna. The maximum output power is
achieved with a load impedance of ZLoad,opt = (255 + j192)Ω. There must be a low resistive path
to VS to deliver the DC current.
The delivered current pulse of the power amplifier is 9 mA and the maximum output power is
delivered to a resistive load of 400Ω if the 1.0 pF output capacitance of the power amplifier is
compensated by the load impedance.
An optimum load impedance of:
Z
Load = 400Ω || j/(2 × π 1.0 pF) = (255 + j192)Ω thus results for the maximum output power of
8 dBm.
The load impedance is defined as the impedance seen from the T5753’s ANT1, ANT2 into the
matching network. Do not confuse this large signal load impedance with a small signal input
impedance delivered as input characteristic of RF amplifiers and measured from the application
into the IC instead of from the IC into the application for a power amplifier.
Less output power is achieved by lowering the real parallel part of 400Ωwhere the parallel imag-
inary part should be kept constant.
Output power measurement can be done with the circuit of Figure 4-2. Note that the component
values must be changed to compensate the individual board parasitics until the T5753 has the
right load impedance ZLoad,opt = (255 + j192)Ω. Also the damping of the cable used to measure
the output power must be calibrated out.
5
4510I–RKE–02/07
Figure 4-2. Output Power Measurement at f = 315 MHz
VS
C1
1 nF
L1 56 nH
Power
meter
Z = 50Ω
C2
ANT1
3.3 pF
ZLopt
Rin
50Ω
ANT2
Note:
For 345 MHz C2 has to be changed to 2.7 pF
4.4
Application Circuit
For the blocking of the supply voltage a capacitor value of C3 = 68 nF/X7R is recommended
(see Figure 4-3 on page 7 and Figure 4-4 on page 8). C1 and C2 are used to match the loop
antenna to the power amplifier where C1 typically is 22 pF/NP0 and C2 is 10.8 pF/NP0
(18 pF + 27 pF in series); for C2 two capacitors in series should be used to achieve a better tol-
erance value and to have the possibility to realize the ZLoad,opt by using standard valued
capacitors.
C1 forms together with the pins of T5753 and the PCB board wires a series resonance loop that
suppresses the 1st harmonic, hence the position of C1 on the PCB is important. Normally the
best suppression is achieved when C1 is placed as close as possible to the pins ANT1 and
ANT2.
The loop antenna should not exceed a width of 1.5 mm, otherwise the Q-factor of the loop
antenna is too high.
L1 ([50 nH to 100 nH) can be printed on PCB. C4 should be selected that the XTO runs on the
load resonance frequency of the crystal. Normally, a value of 12 pF results for a 15 pF
load-capacitance crystal.
6
T5753
4510I–RKE–02/07
T5753
Figure 4-3. ASK Application Circuit
S1
VDD
VSS
BPXY
BPXY
BPXY
OSC1
ATARx9x
VS
1
S2
20
BPXY
7
T5753
Power up/down
CLK
ENABLE
f
4
1
2
8
7
f
32
PA_ENABLE
GND
PDF
CP
C3
C2
ANT2
VS
3
4
6
5
VS
Loop
Antenna
LF
C1
ANT1
XTAL
XTAL
PA
VCO
XTO
PLL
L1
C4
VS
7
4510I–RKE–02/07
Figure 4-4. FSK Application Circuit
S1
VDD
BPXY
BPXY
BPXY
OSC1
ATARx9x
VS
1
20
18
S2
VSS
BP42/T2O
BPXY
7
T5753
Power up/down
CLK
ENABLE
f
4
1
2
8
7
f
32
PA_ENABLE
GND
PDF
CP
C3
C2
ANT2
VS
3
4
6
5
Loop
Antenna
LF
VS
C1
C5
XTAL
ANT1
XTAL
PA
VCO
XTO
PLL
L1
C4
VS
8
T5753
4510I–RKE–02/07
T5753
Figure 4-5. ESD Protection Circuit
VS
ANT1
ANT2
CLK
PA_ENABLE
XTAL
ENABLE
GND
5. Absolute Maximum Ratings
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Parameters
Symbol
Minimum
Maximum
Unit
V
Supply voltage
VS
5
100
Power dissipation
Junction temperature
Storage temperature
Ambient temperature
Input voltage
Ptot
mW
°C
°C
°C
V
Tj
Tstg
150
–55
–55
–0.3
125
Tamb
125
(VS + 0.3)(1)
VmaxPA_ENABLE
Note:
1. If VS + 0.3 is higher than 3.7V, the maximum voltage will be reduced to 3.7V.
6. Thermal Resistance
Parameters
Symbol
Value
Unit
Junction ambient
RthJA
170
K/W
7. Electrical Characteristics
VS = 2.0V to 4.0V, Tamb = –40°C to 125°C unless otherwise specified.
Typical values are given at VS = 3.0V and Tamb = 25°C. All parameters are referred to GND (pin 7).
Parameters
Test Conditions
Symbol
Min.
Typ.
Max.
Unit
Power down,
VENABLE < 0.25 V, -40°C to 85°C
350
7
nA
µA
nA
Supply current
VPA-ENABLE < 0.25 V, -40°C to +125°C
IS_Off
VPA-ENABLE < 0.25 V, 25°C
(100% correlation tested)
< 10
Power up, PA off, VS = 3 V,
Supply current
Supply current
Output power
IS
3.7
9
4.8
mA
mA
VENABLE > 1.7 V, VPA-ENABLE < 0.25 V
Power up, VS = 3.0 V,
VENABLE > 1.7 V, VPA-ENABLE > 1.7 V
IS_Transmit
PRef
11.6
10.5
VS = 3.0V, Tamb = 25°C,
f = 315 MHz, ZLoad = (255 + j192)W
6.0
8.0
dBm
Note:
1. If VS is higher than 3.6V, the maximum voltage will be reduced to 3.6V.
9
4510I–RKE–02/07
7. Electrical Characteristics (Continued)
VS = 2.0V to 4.0V, Tamb = –40°C to 125°C unless otherwise specified.
Typical values are given at VS = 3.0V and Tamb = 25°C. All parameters are referred to GND (pin 7).
Parameters
Test Conditions
Symbol
Min.
Typ.
Max.
Unit
Tamb = –40°C to +85°C,
VS = 3.0V
VS = 2.0V
Output power variation for the full
temperature range
∆PRef
∆PRef
–1.5
–4.0
dB
dB
Tamb = –40°C to +125°C,
VS = 3.0V
VS = 2.0V,
Output power variation for the full
temperature range
∆PRef
∆PRef
–2.0
–4.5
dB
dB
POut = PRef + ∆PRef
Achievable output-power range
Spurious emission
Selectable by load impedance
POut_typ
0
8.0
dBm
fCLK = f0/128
Load capacitance at pin CLK = 10 pF
fO ±1 × fCLK
–55
–52
dBc
dBc
fO ±4 × fCLK
other spurious are lower
f
XTO = f0/32
fXTAL = resonant frequency of the XTAL,
CM ≤ 10 fF, load capacitance selected
Oscillator frequency XTO
(= phase comparator frequency)
fXTO
accordingly
Tamb = –40°C to +85°C,
Tamb = –40°C to +125°C
–30
–40
fXTAL
+30
+40
ppm
ppm
PLL loop bandwidth
250
–116
–86
kHz
Referred to fPC = fXT0,
25 kHz distance to carrier
Phase noise of phase comparator
In loop phase noise PLL
Phase noise VCO
–110
–80
dBc/Hz
25 kHz distance to carrier
dBc/Hz
at 1 MHz
at 36 MHz
–94
–125
–90
–121
dBc/Hz
dBc/Hz
Frequency range of VCO
fVCO
310
350
MHz
Clock output frequency (CMOS
microcontroller compatible)
f0/128
MHz
V0h
V0l
V
V
Voltage swing at pin CLK
CLoad ≤ 10 pF
VS × 0.8
VS × 0.2
Series resonance R of the crystal
Capacitive load at pin XT0
Rs
110
7
Ω
pF
FSK modulation frequency rate
ASK modulation frequency rate
Duty cycle of the modulation signal = 50%
Duty cycle of the modulation signal = 50%
0
0
32
kHz
kHz
32
Low level input voltage
High level input voltage
Input current high
VIl
VIh
IIn
0.25
V
V
µA
ENABLE input
1.7
1.7
20
Low level input voltage
High level input voltage
Input current high
VIl
VIh
IIn
0.25
V
V
µA
(1)
PA_ENABLE input
VS
5
Note:
1. If VS is higher than 3.6V, the maximum voltage will be reduced to 3.6V.
10
T5753
4510I–RKE–02/07
T5753
8. Ordering Information
Extended Type Number
Package
TSSOP8L
TSSOP8L
Remarks
T5753-6AQJ
Taped and reeled, Marking: T573, Pb-free
T5753-6APJ
Taped and reeled, Marking: T573, small reel, Pb-free
Note:
1. J = –40°C to +125°C + lead-free
9. Package Information
Package: TSSOP 8L
Dimensions in mm
3±0.1
3±0.1
+0.06
3.8±0.3
4.9±0.1
0.31-0.07
0.65 nom.
3 x 0.65 = 1.95 nom.
8
5
4
technical drawings
according to DIN
specifications
1
Drawing-No.: 6.543-5083.01-4
Issue: 2; 15.03.04
11
4510I–RKE–02/07
10. Revision History
Please note that the following page numbers referred to in this section refer to the specific revision
mentioned, not to this document.
Revision No.
History
• Put datasheet in a new template
• Pb-free Logo on page 1 deleted
4510I-RKE-02/07
4510H-RKE-09/05
• Pb-free Logo on page 1 added
• Put datasheet in a new template
• Section 1 “Description” on page 1 changed
• Figure title Figure 4-2 on page 6 changed
• Table “Electrical Characteristics” on pages 9 to 10 changed
• Table “Ordering Information” on page 11 changed
4510G-RKE-02/05
4510F-RKE-02/05
• Table “Absolute Maximum Ratings” (page 8): row “Input voltage” added
• Table “Absolute Maximum Ratings” (page 8): table note 1 added
• Table “Electrical Characteristics” (page 10): row “PA_ENABLE input“ changed
• Table “Electrical Characteristics” (page 10): table note 1 added
• Table “Ordering Information” (page 11): Remarks changed
12
T5753
4510I–RKE–02/07
Atmel Corporation
Atmel Operations
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Memory
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
Tel: (49) 71-31-67-0
Fax: (49) 71-31-67-2340
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
Microcontrollers
Regional Headquarters
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Europe
Atmel Sarl
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
Tel: (41) 26-426-5555
Fax: (41) 26-426-5500
Fax: 1(719) 540-1759
Biometrics
Avenue de Rochepleine
BP 123
38521 Saint-Egreve Cedex, France
Tel: (33) 4-76-58-47-50
Fax: (33) 4-76-58-47-60
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
Tel: (33) 2-40-18-18-18
Fax: (33) 2-40-18-19-60
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
ASIC/ASSP/Smart Cards
Zone Industrielle
13106 Rousset Cedex, France
Tel: (33) 4-42-53-60-00
Fax: (33) 4-42-53-60-01
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Fax: 1(719) 540-1759
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
Tel: (44) 1355-803-000
Fax: (44) 1355-242-743
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI-
TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN-
TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT
OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life.
© 2007 Atmel Corporation. All rights reserved. Atmel®, logo and combinations thereof, Everywhere You Are® and others are registered trade-
marks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
4510I–RKE–02/07
相关型号：
T5753-6AQ
UHF ASK/FSK TRANSMITTERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ATMEL
T5753-6AQJ
UHF ASK/FSK TransmitterWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ATMEL
T5753C-6APJ
Telecom Circuit, 1-Func, Bipolar, PDSO8, LEAD FREE, TSSOP-8Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ATMEL
T5753C-6AQJ
Telecom Circuit, 1-Func, PDSO8Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MICROCHIP
T5753C-6AQJ
Telecom Circuit, 1-Func, Bipolar, PDSO8, LEAD FREE, TSSOP-8Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ATMEL
T5753C-6AQJ-66
IC TX UHF ASK/FSK 8TSSOPWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MICROCHIP
T5753_07
UHF ASK/FSK TransmitterWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ATMEL
T5753_08
UHF ASK/FSK TransmitterWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ATMEL
T5754
UHF ASK/FSK TRANSMITTERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ATMEL
T5754-6AP
Telecom IC, Bipolar, PDSO8Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ATMEL
T5754-6APJ
UHF ASK/FSK TransmitterWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ATMEL
T5754-6AQ
UHF ASK/FSK TRANSMITTERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ATMEL
©2020 ICPDF网 联系我们和版权申明