SFX-200G-CFF-M2M5P2P5 [CONNOR-WINFIELD]
Support Circuit, 1-Func, 1.200 X 1 INCH, 0.285 INCH HEIGHT, ROHS COMPLIANT, SURFACE MOUNT PACKAGE-16/12;
| 型号： | SFX-200G-CFF-M2M5P2P5 |
| 厂家： | 
CONNOR-WINFIELD CORPORATION |
| 描述： | Support Circuit, 1-Func, 1.200 X 1 INCH, 0.285 INCH HEIGHT, ROHS COMPLIANT, SURFACE MOUNT PACKAGE-16/12 ATM 异步传输模式 电信 电信集成电路 |
| 文件： | 总8页 (文件大小：135K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
SFX-200G
Synchronous Clock
Generators
PLL
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630-851-4722
Fax: 630- 851-5040
www.conwin.com
Applications
• SONET / SDH / ATM
• DWDM / FDM
• FEC (Forward Error Correction)
Features
• Available as a 5.0V or 3.3V High Precision PLL
• Two User Selectable PECL Input References Frequencies
• Two user Selectable PECL Output Frequencies
• Jitter Generation OC-192 Compliant
• 1.2” x 1.0” x 0.285”, Surface Mount
• RoHS Compliant
Bulletin
SG152
Page
1 of 8
Revision
00
Date
2 MAY 07
Issued By
ENG
General Description
The SFX-200G is a high precision frequency translator that
translates one of two inputs, greater than 1MHz, to one of two
selectable output frequencies between 77.76 MHz and 777.6
MHz. The SFX-200G supports all major FEC rates such as 15/
14, 255/237 etc.
SFX-200G is well suited for use in line cards, service
termination cards and similar functions to provide reliable
reference, phase locked, synchronization for TDM, PDH,
SONET and SDH network equipment. The SFX-200G provides
a jitter filtered, wander following output signal synchronized to
a superior Stratum or peer input reference signal.
The SFX-200G includes a lock detect alarm output. The
PLL control voltage is brought out through a 470 kΩ resistor
and can be used to determine when the pull range limits are
reached.The LVPECL outputs may be put into the tri-state high
impedance condition for external testing purposes by asserting
a high signal to the Enable/Disable pin.
The SFX-200G package typical dimensions are 1.2" x 1.0"
x 0.285". Parts are assembled using high temperature solder
to withstand surface mount reflow process.
Functional Block Diagram
Figure 1
SFX-200G
LD
(Pin 10)
470 kΩ
Monitor
(Pin 11)
In
Input A
Input B
Q
(Pin 1)
(Pin 12)
Frequency
Divider
Loop
Filter
PECL
CIn
(Pin 2)
*Note 2.0
Q
VCXO 1
(Pin 14)
Frequency
Divider
PECL
In Sel
Microprocessor
VCXO 2
(Pin 7)
Out Sel
(Pin 8)
Disable
(Pin 16)
Absolute Maximum Rating
Table 1
Symbol
Vcc
Parameter
Minimum
Nominal
Maximum
Units
Notes
Power Supply Voltage (OptionC)
Power Supply Voltage (OptionD)
-0.3
-0.3
5.5
3.8
Volts
Volts
V
I
Input Voltage
-0.2
Vcc
Volts
Ts
Storage Temperature (OptionF)
Storage Temperature (OptionC)
-55
-40
125
85
°C
°C
Data Sheet #: SG152 Page 2 of 8
Rev: 00
Date: 5/2/07
© Copyright 2007 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
Specifications
Table 2
Symbol
Parameter
Minimum
Nominal
Maximum
777.6
Units
MHz
MHz
MHz
Notes
3.0
f
Input Frequencies (Comp PECL)
1
IN
Input Frequencies (HCMOS
)
1
100
2.0
fOUT
Output Frequencies (Comp PECL)
77.76
777.6
Vcc
Supply Voltage (C = 5.0 VDC
)
)
4.75
3.15
5.0
3.3
5.25
3.45
Volts
Volts
(D = 3.3 VDC
ICC
Supply Current
80
mA
V
VOH
VOL
High Level Output Voltage
Low Level Output Voltage
2.275
45
1.68
V
TR/T
Rise/Fall Time - 622MHz
155 MHz
250
600
400
1500
ps
ps
F
SYM
JGEN
Output Symmetry
55
1
%
Jitter Generation RMS
(12 kHz - 20 MHz)
0.5
ps
JTRAN
APR
TOP
Jitter Transfer
0.1
dB
1.0
Input Frequency Tracking
Operating Temperature
±50
ppm
F =
C =
-40
0
85
70
°C
°C
NOTES: 1.0: GR-253-CORE, Sec. 5.6.2.1.2
2.0: For reference inputs <100MHz, CIN (Pin 2) is not used and is not terminated internally. For Complementary Inputs ≥100 MHz, Both IN
(Pin 1) and CIN (Pin 2) are required.
3.0: Both reference inputs frequencies must be either <100 MHz or ≥100 MHz. Reference A <100 MHz and Reference B ≥100 MHz
is not supported.
Pin Description
Table 3
Pin #
Connection
Description
1
2
In
Input Frequency, Signal is AC coupled
CIn
Complementary Input Frequency, Signal is AC coupled
3
----
Missing
4
----
Missing
5
----
Missing
6
----
Missing
7
In Sel
Out Sel
Vcc
Input Frequency Select - Logic “0” = Input Freq. A, Logic “1” = Input Freq. B
Output Frequency Select - Logic “0” = Output Freq. #1, Logic “1” = Output Freq. #2
Supply Voltage
8
9
10
LD (Output)
Lock Detect
Logic “1” indicates that the unit is locked to the input reference
Logic “0” indicates that the reference is lost or out of lock range
11
Monitor (Output)
Control voltage level for the PECL oscillator and is brought out through
a 470kΩ resistor
12
13
14
15
16
Q
PECL Output
GND
Ground
Q
PECL Complemetary Output
Ground
GND
Disable (Input)
Logic “0” (or no connect) = PECL Outputs are Enabled
Logic “1”
= PECL Outputs are put into Tri-State High Impedence
Data Sheet #: SG152 Page 3 of 8
Rev: 00
Date: 5/2/07
© Copyright 2007 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
Output Load and Power Supply Filtering Recommendations
Figure 2
*
It is highly recommended
*
*
*
that either a linear regulator
or bypass capacitors be
used. Typical values would
be 10 uF, 0.1 uF, 100 pF.
VCC -2 VDC
SFX-200G
LD
(Pin 10)
470 kΩ
50Ω
50Ω
Monitor
(Pin 11)
In
Input A
Input B
Q
(Pin 1)
(Pin 12)
Frequency
Divider
Loop
Filter
PECL
(FOUT
)
CIn
Q
VCXO 1
(Pin 2)
(Pin 14)
Frequency
Divider
PECL
In Sel
Microprocessor
VCXO 2
(Pin 7)
Out Sel
(Pin 8)
Disable
(Pin 16)
Package Dimensions
Figure 3
Recommended Footprint Dimensions
Figure 4
0.150
[3.81mm]
1.000
[25.40mm]
0.700
[17.78mm]
9
10 11 12 13 14 15 16
16
9
1.200
[30.48mm]
8
7
2
1
Pin 1
0.100
[2.54mm]
0.980
[24.89mm]
1
8
0.279
[7.09mm]
(0.285" MAX)
Data Sheet #: SG152 Page 4 of 8
Rev: 00
Date: 5/2/07
© Copyright 2007 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
Solder Profile
Figure 5
300
250
200
150
100
50
Peak Temp.
245°-255°C for 15 sec Typ.
221°C
Reflow Zone
30/90 sec
(Min/Max)
Soaking Zone
60-90 sec Typ.
(2 min Max)
Ramp Slope not
to exceed
3°C/sec
0
0
50
100
150
200
250
300
350
Time (sec)
Data Sheet #: SG152 Page 5 of 8
Rev: 00
Date: 5/2/07
© Copyright 2007 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
Standard Frequencies
1.0240 MHz
1.5440 MHz
2.0480 MHz
4.0960 MHz
6.4800 MHz
8.1920 MHz
10.0000 MHz
12.8000 MHz
13.0000 MHz
15.0000 MHz
16.3840 MHz
19.4400 MHz
20.0000 MHz
20.1416 MHz
20.4800 MHz
B2
B3
B4
B5
C2
C3
C4
D2
D3
D4
D5
D6
E2
E3
E4
22.2171 MHz
26.0000 MHz
27.0000 MHz
29.4912 MHz
32.7680 MHz
37.0560 MHz
38.8800 MHz
44.4343 MHz
44.7360 MHz
51.8400 MHz
61.4400 MHz
65.5360 MHz
77.7600 MHz
78.1250 MHz
78.6432 MHz
E5
F3
F4
F5
H3
H4
H5
J2
82.9440 MHz
112.0000 MHz
114.0000 MHz
125.0000 MHz
139.2640 MHz
155.5200 MHz
156.2500 MHz
161.1328 MHz
166.6286 MHz
167.3316 MHz
168.0407 MHz
311.0400 MHz
622.0800 MHz
624.7048 MHz
K6
L2
L3
625.0000 MHz
627.3596 MHz
644.5312 MHz
666.5143 MHz
669.1281 MHz
669.3266 MHz
672.1627 MHz
690.5692 MHz
710.9486 MHz
719.7344 MHz
777.6000 MHz
No 2nd Input Freq.
Input Freq. not listed
Output Freq. not listed
P3
P7
P4
P5
R2
R3
R5
R4
T2
T3
T4
XX
SS
SS
L4
L5
M2
M3
M4
M5
N2
N3
P1
P2
P6
J3
J4
J5
J6
K2
K3
K5
Ordering Information
SFX-200G- D F C - M2 M5 P2 P5
Output Frequency 2 (K3 to T4)
See standard frequencies chart above.
* If the desired frequency is not listed, enter
SS in this block and add the frequency after
the part number. Consult a sales representative
for availabilty of additional frequencies.
** Output Frequency 2 must be greater than
Output Frequency 1
Supply Voltage
C = 5.0 VDC
D = 3.3 VDC
Output Logic
F = Comp. PECL
Output Frequency 1 (K2 to T3)
See standard frequencies chart above.
* If the desired frequency is not listed, enter
SS in this block and add the frequency after
the part number. Consult a sales representative
for availabilty of additional frequencies.
** Output Frequency 1 must be less than
Output Frequency 2
Temperature Range
C = 0˚C to 70˚C
F = -40˚C to 85˚C
Input Frequency A (B2 to R4)
Input Frequency B (B3 to R4)
See standard frequencies chart above. If a
second input frequency is not required, place XX
in this location.
* If the desired frequency is not listed, enter
SS in this block and add the frequency after
the part number. Consult a sales representative
for availabilty of additional frequencies.
** Input B must be greater than Input A
(See Note 3.0, pg 3)
See standard frequencies chart above.
* If the desired frequency is not listed, enter
SS in this block and add the frequency after
the part number. Consult a sales representative
for availabilty of additional frequencies.
** Input A must be less than Input B
(See Note 3.0, pg 3)
Data Sheet #: SG152 Page 6 of 8
Rev: 00
Date: 5/2/07
© Copyright 2007 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
Data Sheet #: SG152 Page 7 of 8
Rev: 00
Date: 5/2/07
© Copyright 2007 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630-851-4722
Fax: 630-851-5040
www.conwin.com
Revision
00
Revision Date
5/2/07
Note
Final Release
相关型号：
SFX-200G-DFC-M2M5P2P5
Support Circuit, 1-Func, 1.200 X 1 INCH, 0.285 INCH HEIGHT, ROHS COMPLIANT, SURFACE MOUNT PACKAGE-16/12
CONNOR-WINFIE
SFX-200G-DFF-M2M5P2P5
Support Circuit, 1-Func, 1.200 X 1 INCH, 0.285 INCH HEIGHT, ROHS COMPLIANT, SURFACE MOUNT PACKAGE-16/12
CONNOR-WINFIE
SFX-400G-DFC-D6D6P2P4P5R3
Support Circuit, 1-Func, 1.200 X 1 INCH, 0.285 INCH HEIGHT, ROHS COMPLIANT, SURFACE MOUNT PACKAGE-16
CONNOR-WINFIE
SFX-424G-DAC-F1XX
Support Circuit, 1-Func, ROHS COMPLIANT, SURFACE MOUNT PACKAGE-14/13
CONNOR-WINFIE
SFX-424G-DAF-A1XX
Support Circuit, 1-Func, ROHS COMPLIANT, SURFACE MOUNT PACKAGE-14/13
CONNOR-WINFIE
SFX-424G-DFF-A3XX
Support Circuit, 1-Func, ROHS COMPLIANT, SURFACE MOUNT PACKAGE-14/13
CONNOR-WINFIE
SFX-424G-DFF-F1XX
Support Circuit, 1-Func, ROHS COMPLIANT, SURFACE MOUNT PACKAGE-14/13
CONNOR-WINFIE
SFX-424G-DFF-F2XX
Support Circuit, 1-Func, ROHS COMPLIANT, SURFACE MOUNT PACKAGE-14/13
CONNOR-WINFIE
©2020 ICPDF网 联系我们和版权申明