CYD18S72V18 [CYPRESS]
FullFlex Synchronous SDR Dual Port SRAM;型号: | CYD18S72V18 |
厂家: | CYPRESS |
描述: | FullFlex Synchronous SDR Dual Port SRAM 静态存储器 |
文件: | 总53页 (文件大小:755K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
FullFlex™ Synchronous SDR
Dual Port SRAM
FullFlex™ Synchronous SDR Dual Port SRAM
Features
Functional Description
■ True dual port memory enables simultaneous access the
shared array from each port
The FullFlex™ dual port SRAM families consist of 2-Mbit, 9-Mbit,
18-Mbit, and 36-Mbit synchronous, true dual port static RAMs
that are high speed, low power 1.8 V or 1.5 V CMOS. Two ports
are provided, enabling simultaneous access to the array.
Simultaneous access to a location triggers deterministic access
control. For FullFlex72 these ports operate independently with
72-bit bus widths and each port is independently configured for
two pipelined stages. Each port is also configured to operate in
pipelined or flow through mode.
■ Synchronous pipelined operation with single data rate (SDR)
operation on each port
❐ SDR interface at 200 MHz
❐ Up to 28.8 Gb/s bandwidth (200 MHz × 72-bit × 2 ports)
■ Selectable pipelined or flow-through mode
■ 1.5 V or 1.8 V core power supply
The advanced features include the following:
■ Commercial and Industrial temperature
■ IEEE 1149.1 JTAG boundary scan
■ Built in deterministic access control to manage address
collisions during simultaneous access to the same memory
location
■ Available in 484-ball PBGA (× 72) and 256-ball FBGA (× 36
and × 18) packages
■ Variable impedance matching (VIM) to improve data
transmission by matching the output driver impedance to the
line impedance
■ FullFlex72 family
❐ 36-Mbit: 512 K × 72 (CYD36S72V18)
❐ 18-Mbit: 256 K × 72 (CYD18S72V18)
❐ 9-Mbit: 128 K × 72 (CYD09S72V18)
■ Echo clocks to improve data transfer
To reduce the static power consumption, chip enables power
down the internal circuitry. The number of latency cycles before
a change in CE0 or CE1 enables or disables the databus
matches the number of cycles of read latency selected for the
device. For a valid write or read to occur, activate both chip
enable inputs on a port.
■ FullFlex36 family
❐ 36-Mbit: 1 M × 36 (CYD36S36V18)
❐ 18-Mbit: 512 K × 36 (CYD18S36V18)
❐ 9-Mbit: 256 K × 36 (CYD09S36V18)
❐ 2-Mbit: 64 K × 36 (CYD02S36V18)
Each port contains an optional burst counter on the input address
register. After externally loading the counter with the initial
address, the counter increments the address internally.
■ FullFlex18 family
❐ 36-Mbit: 2 M × 18 (CYD36S18V18)
❐ 18-Mbit: 1 M × 18 (CYD18S18V18)
❐ 9-Mbit: 512 K × 18 (CYD09S18V18)
Additional device features include a mask register and a mirror
register to control counter increments and wrap around. The
counter interrupt (CNTINT) flags notify the host that the counter
reaches maximum count value on the next clock cycle. The host
reads the burst counter internal address, mask register address,
and busy address on the address lines. The host also loads the
counter with the address stored in the mirror register by using the
retransmit functionality. Mailbox interrupt flags are used for
message passing, and JTAG boundary scan and asynchronous
Master Reset (MRST) are also available. The Logic Block
Diagram on page 2 shows these features.
■ Built in deterministic access control to manage address
collisions
❐ Deterministic flag output upon collision detection
❐ Collision detection on back-to-back clock cycles
❐ First busy address readback
■ Advanced features for improved high speed data transfer and
flexibility
❐ Variable impedance matching (VIM)
❐ Echo clocks
❐ Selectable LVTTL (3.3 V), Extended HSTL (1.4 V to 1.9 V),
1.8 V LVCMOS, or 2.5 V LVCMOS IO on each port
❐ Burst counters for sequential memory access
❐ Mailbox with interrupt flags for message passing
❐ Dual chip enables for easy depth expansion
The FullFlex72 is offered in a 484-ball plastic BGA package. The
FullFlex36 and FullFlex18 are available in 256-ball fine pitch
BGA package except the 36-Mbit devices which are offered in
484-ball plastic BGA package.
Cypress Semiconductor Corporation
Document Number: 38-06082 Rev. *O
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised February 5, 2013
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Logic Block Diagram
The Logic Block Diagram for FullFlex72, FullFlex36, and FullFlex18 family follows: [1, 2, 3]
FTSEL
L
FTSEL
R
CQEN
L
CQEN
R
CONFIG Block
CONFIG Block
PORTSTD[1:0]
PORTSTD[1:0]
R
L
DQ [71:0]
R
DQ[71:0]
L
BE [7:0]
BE [7:0]
R
L
CE
CE1
OE
0
CE
0
L
R
R
IO
Control
IO
Control
CE1
OE
L
R
L
R/
W
R/
W
L
R
CQ1
L
L
CQ1
CQ1
CQ0
R
CQ1
CQ0
R
R
L
CQ0
CQ0
L
R
Dual Port Array
BUSY
Collision Detection Logic
BUSY
L
R
A [20:0]
A [20:0]
L
R
CNT/MSK
CNT/MSK
L
R
ADS
ADS
L
R
CNTEN
CNTEN
L
R
Address &
Counter Logic
Address &
Counter Logic
CNTRST
CNTRST
L
R
RET
RET
R
L
CNTINT
L
CNTINT
R
C
C
L
R
WRP
L
WRP
R
TRST
TMS
TDI
Mailboxes
INT
INT
R
L
JTAG
TDO
TCK
ZQ0
ZQ0
ZQ1
R
L
ZQ1
R
L
RESET
LOGIC
MRST
READY
READY
L
R
LowSPD
LowSPD
R
L
Notes
1. The CYD36S18V18 device has 21 address bits. The CYD36S36V18 and CYD18S18V18 devices have 20 address bits. The CYD36S72V18, CYD18S36V18, and
CYD09S18V18 devices have 19 address bits. The CYD18S72V18 and CYD09S36V18 devices have 18 address bits. The CYD09S72V18 device has 17 address bits.
The CYD02S36V18 has 16 address bits.
2. The FullFlex72 family of devices has 72 data lines. The FullFlex36 family of devices has 36 data lines. The FullFlex18 family of devices has 18 data lines.
3. The FullFlex72 family of devices has eight byte enables. The FullFlex36 family of devices has four byte enables. The FullFlex18 family of devices has two byte enables.
Document Number: 38-06082 Rev. *O
Page 2 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Contents
Selection Guide ................................................................9
Pin Definitions ..................................................................9
Selectable IO Standard .............................................11
Clocking .....................................................................11
Selectable Pipelined or Flow through Mode ..............11
DLL ............................................................................11
Echo Clocking ...........................................................11
Deterministic Access Control ....................................11
Variable Impedance Matching .......................................12
Address Counter and Mask Register Operations ..... 13
Counter Load Operation ............................................13
Mask Load Operation ................................................13
Counter Readback Operation ....................................13
Mask Readback Operation ........................................13
Counter Reset Operation ..........................................13
Mask Reset Operation ...............................................13
Increment Operation ..................................................15
Hold Operation ..........................................................15
Retransmit .................................................................15
Counter Interrupt .......................................................15
Counting by Two .......................................................15
Counting by Four .......................................................15
Mailbox Interrupts ......................................................15
Master Reset .............................................................18
IEEE 1149.1 Serial Boundary Scan (JTAG) ..................18
Maximum Ratings ...........................................................19
Operating Range .............................................................19
Power Supply Requirements .........................................19
Electrical Characteristics ...............................................19
Electrical Characteristics ...............................................21
Electrical Characteristics ...............................................24
Capacitance ....................................................................24
Thermal Resistance ........................................................24
AC Test Load and Waveforms .......................................25
Switching Characteristics ..............................................26
Switching Waveforms ....................................................29
Ordering Information ......................................................43
512 K × 72 (36-Mbit) 1.8 V/1.5 V Synchronous
CYD36S72V18 Dual Port SRAM ......................................43
256 K × 72 (18-Mbit) 1.8 V/1.5 V Synchronous
CYD18S72V18 Dual Port SRAM ......................................43
128 K × 72 (9-Mbit) 1.8 V/1.5 V Synchronous
CYD09S72V18 Dual Port SRAM ......................................43
1024 K × 36 (36-Mbit) 1.8 V/1.5 V Synchronous
CYD36S36V18 Dual Port SRAM ......................................43
512 K × 36 (18-Mbit) 1.8 V/1.5 V Synchronous
CYD18S36V18 Dual Port SRAM ......................................43
256 K × 36 (9-Mbit) 1.8 V/1.5 V Synchronous
CYD09S36V18 Dual Port SRAM ......................................44
64 K × 36 (2-Mbit) 1.8 V or 1.5 V Synchronous
CYD02S36V18 Dual Port SRAM ......................................44
2048 K × 18 (36-Mbit) 1.8 V/1.5 V Synchronous
CYD36S18V18 Dual Port SRAM ......................................45
1024 K × 18 (18-Mbit) 1.8 V/1.5 V Synchronous
CYD18S18V18 Dual Port SRAM ......................................45
512 K × 18 (9-Mbit) 1.8 V/1.5 V Synchronous
CYD09S18V18 Dual Port SRAM ......................................45
Ordering Code Definitions .........................................45
Package Diagrams ..........................................................46
Acronyms ........................................................................49
Document Conventions .................................................49
Units of Measure .......................................................49
Document History Page .................................................50
Sales, Solutions, and Legal Information ......................53
Worldwide Sales and Design Support .......................53
Products ....................................................................53
PSoC Solutions .........................................................53
Document Number: 38-06082 Rev. *O
Page 3 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Figure 1. FullFlex72 SDR 484-ball BGA Pinout (Top View)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
DNU DQ61L DQ59L DQ57L DQ54L DQ51L DQ48L DQ45L DQ42L
DQ63L DQ62L DQ60L DQ58L DQ55L DQ52L DQ49L DQ46L DQ43L
DQ39L DQ36L DQ36R DQ39R
DQ40L DQ37L DQ37R DQ40R
DQ41L DQ38L DQ38R DQ41R
DQ42R DQ45R DQ48R DQ51R DQ54R DQ57R DQ59R DQ61R DNU
DQ43R DQ46R DQ49R DQ52R DQ55R DQ58R DQ60R DQ62R DQ63R
A
B
C
D
E
DQ65L DQ64L
DQ67L DQ66L
VSS
VSS
VSS
DQ56L DQ53L DQ50L DQ47L DQ44L
LOWSPDL
DQ44R DQ47R DQ50R DQ53R DQ56R VSS
VSS
VSS
DQ64R DQ65R
DQ66R DQ67R
[4]
PORTSTD0L
PORTSTD1L
ZQ0L
VSS
VSS
CQ1L
CQ1L
VSS
BUSYL CNTINTL
VTTL
DNU
CQ1R
CQ1R
VSS
VSS
VSS
DQ69L DQ68L VDDIOL
DQ71L DQ70L CE1L
VSS
VSS VDDIOL VDDIOL VDDIOL VDDIOL VDDIOL VTTL VTTL
VDDIOR VDDIOR VDDIOR VDDIOR DNU
VDDIOR DQ68R DQ69R
VCORE
CE0L VDDIOL VDDIOL VDDIOL VDDIOL VDDIOL VCORE
VCORE VCORE VDDIOR VDDIOR VDDIOR VDDIOR VDDIOR CE0R
CE1R
RETR
WRPR
DQ70R DQ71R
F
A0L
A2L
A4L
A6L
A8L
A1L
A3L
RETL
BE4L VDDIOL VDDIOL VREFL
BE5L VDDIOL VDDIOL VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VCORE
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VREFR VDDIOR VDDIOR BE4R
VSS VDDIOR VDDIOR BE5R
A1R
A3R
A0R
A2R
G
H
J
WRPL
A5L READYL BE6L VDDIOL VDDIOL VSS
[4, 5]
VSS VDDIOR VDDIOR BE6R READYR A5R
[4, 5]
A4R
A7L ZQ1L
BE7L
VTTL VCORE
VTTL VCORE
VTTL VCORE
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VCORE VDDIOR BE7R ZQ1R
A7R
A6R
K
L
A9L
CL
VSS
OEL
VCORE VTTL
VCORE VTTL
VCORE VTTL
OER
BE3R
BE2R
CR
VSS
A9R
A8R
A10L A11L
A12L A13L
A14L A15L
BE3L
A11R
A13R
A15R
A10R
A12R
A14R
M
N
P
ADSL
BE2L VDDIOL VCORE
ADSR
CNT/MSKR
CNT/MSKL
BE1L VDDIOL VDDIOL VSS
VSS VDDIOR VDDIOR BE1R
[8]
[7]
[7]
[8]
A16L A17L
CNTENL BE0L VDDIOL VDDIOL VSS
VSS VDDIOR VDDIOR BE0R CNTENR A17R
A16R
R
T
[6]
[6]
CNTRSTR
A18L
DNU CNTRSTL INTL VDDIOL VDDIOL VREFL
VREFR VDDIOR VDDIOR INTR
DNU A18R
DQ35L DQ34L R/WL
DQ33L DQ32L FTSELL
CQENL VDDIOL VDDIOL VDDIOL VDDIOL VDDIOL VCORE
VCORE VCORE VDDIOR VDDIOR VDDIOR VDDIOR VDDIOR CQENR R/WR
DQ34R DQ35R
U
V
VDDIOL
MRST
VSS
VDDIOR
TDI
DNU VDDIOL VDDIOL VDDIOL VDDIOL
VTTL
CNTINTR
DQ5L
VTTL VTTL VDDIOR VDDIOR VDDIOR VDDIOR VDDIOR TRST
FTSELR DQ32R DQ33R
[4]
PORTSTD1R
PORTSTD0R
BUSYR
LOWSPDR
DQ31L DQ30L
DQ29L DQ28L
VSS
VSS
VSS
CQ0L
CQ0L
DNU
ZQ0R
VSS
CQ0R
CQ0R
VSS
TDO
TCK
DQ30R DQ31R
DQ28R DQ29R
W
Y
DQ20L DQ17L DQ14L DQ11L
DQ8L
DQ7L
DQ6L
DQ2L DQ2R
DQ1L DQ1R
DQ0L DQ0R
DQ5R
DQ4R
DQ3R
DQ8R DQ11R DQ14R DQ17R DQ20R TMS
DQ27L DQ26L DQ24L DQ22L DQ19L DQ16L DQ13L DQ10L
DNU DQ25L DQ23L DQ21L DQ18L DQ15L DQ12L DQ9L
DQ4L
DQ7R
DQ10R DQ13R DQ16R DQ19R DQ22R DQ24R DQ26R DQ27R
DQ9R DQ12R DQ15R DQ18R DQ21R DQ23R DQ25R DNU
AA
AB
DQ3L
DQ6R
Notes
4. Leave this ball unconnected to disable VIM.
5. This ball is applicable only for 36-Mbit and DNU for 18-Mbit and lower densities.
6. Leave this Ball unconnected for CYD18S72V18 and CYD09S72V18.
7. Leave this Ball unconnected for CYD09S72V18.
8. Leave this Ball unconnected for CYD04S72V18.
Document Number: 38-06082 Rev. *O
Page 4 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Figure 2. FullFlex36 SDR 484-ball BGA Pinout (Top View)[9]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21 22
DNU DNU
DNU DNU
DNU DNU
DNU DNU
DNU DNU
DNU DNU
DNU DNU
DNU DNU
DNU
DNU
VSS
VSS
DNU
DNU
VSS
VSS
VSS
DNU
DNU
DNU
VSS
DQ33L DQ30L DQ27L DQ24L
DQ34L DQ31L DQ28L DQ25L
DQ35L DQ32L DQ29L DQ26L
DQ21L DQ18L DQ18R DQ21R
DQ22L DQ19L DQ19R DQ22R
DQ23L DQ20L DQ20R DQ23R
DQ24R DQ27R DQ30R DQ33R
DQ25R DQ28R DQ31R DQ34R
DNU
DNU
DNU
VSS
DNU
DNU
VSS
VSS
VSS
DNU
DNU
VSS
VSS
A
B
C
D
E
DQ26R DQ29R DQ32R DQ35R
[10]
PORTSTD0L
PORTSTD1L
LOWSPDL
CQ1L
CQ1L
VSS
ZQ0L
BUSYL CNTINTL
VTTL VTTL
DNU
CQ1R
CQ1R
DNU DNU VDDIOL
DNU DNU CE1L
VSS VDDIOL VDDIOR VDDIOR VDDIOR VDDIOR VTTL
VDDIOL VDDIOL VDDIOL VDDIOL DNU
VDDIOR DNU DNU
CE1R DNU DNU
CE0L VDDIOL VDDIOL VDDIOR VDDIOR VDDIOR VCORE VCORE VCORE VCORE VDDIOL VDDIOL VDDIOL VDDIOR VDDIOR CE0R
F
A0L A1L
RETL
BE2L VDDIOL VDDIOL VREFL
BE3L VDDIOL VDDIOL VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VREFR VDDIOR VDDIOR BE2R
VSS VDDIOR VDDIOR BE3R
RETR
A1R A0R
G
H
J
A2L A3L WRPL
WRPR A3R A2R
A4L A5L READYL DNU VDDIOL VDDIOL VSS
[10]
VSS VDDIOR VDDIOR DNU READYR A5R A4R
[10]
A6L A7L ZQ1L
DNU
OEL
DNU
VTTL VCORE
VTTL VCORE
VTTL VCORE
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VCORE VDDIOR DNU
ZQ1R
A7R A6R
A9R A8R
A11R A10R
K
L
A8L A9L
CL
VCORE VTTL
VCORE VTTL
VCORE VTTL
OER
DNU
DNU
CR
A10L A11L
VSS
VSS
M
N
P
A12L A13L ADSL
DNU VDDIOL VCORE
ADSR A13R A12R
CNT/MSKR
A15R A14R
CNT/MSKL
A14L A15L
BE1L VDDIOL VDDIOL VSS
VSS VDDIOR VDDIOR BE1R
VSS VDDIOR VDDIOR BE0R CNTENR A17R A16R
CNTRSTR
A19R A18R
A16L A17L CNTENL BE0L VDDIOL VDDIOL VSS
R
T
CNTRSTL
A18L A19L
INTL VDDIOL VDDIOL VREFL
VREFR VDDIOR VDDIOR INTR
DNU DNU R/WL CQENL VDDIOL VDDIOL VDDIOR VDDIOR VDDIOR VCORE VCORE VCORE VCORE VDDIOL VDDIOL VDDIOL VDDIOR VDDIOR CQENR R/WR DNU DNU
U
V
DNU DNU FTSELL VDDIOL DNU VDDIOR VDDIOR VDDIOR VDDIOR
VTTL
VTTL
VTTL
VDDIOL VDDIOL VDDIOL VDDIOL VDDIOR TRST VDDIOR FTSELR DNU DNU
[10]
PORTSTD1R
PORTSTD0R
LOWSPDR
DQ8R
DNU DNU
DNU DNU
DNU DNU
DNU DNU
VSS
VSS
DNU
DNU
MRST
VSS
VSS
DNU
DNU
DNU
CQ0L
CQ0L
DNU
CNTINTR BUSYR ZQ0R
VSS
CQ0R
CQ0R
VSS
DNU
DNU
DNU
TDI
TMS
DNU
DNU
TDO
TCK
DNU
DNU
DNU DNU
DNU DNU
DNU DNU
DNU DNU
W
Y
DQ17L DQ14L DQ11L
DQ16L DQ13L DQ10L
DQ15L DQ12L DQ9L
DQ8L
DQ7L
DQ6L
DQ5L
DQ4L
DQ3L
DQ2L
DQ1L
DQ0L
DQ2R
DQ5R
DQ4R
DQ3R
DQ11R DQ14R DQ17R
DQ10R DQ13R DQ16R
DQ9R DQ12R DQ15R
DNU
DNU
DQ1R
DQ0R
DQ7R
AA
AB
DQ6R
Notes
9. Use this pinout only for device CYD36S36V18 of the FullFlex36 family.
10. Leave this ball unconnected to disable VIM.
Document Number: 38-06082 Rev. *O
Page 5 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Figure 3. FullFlex18 SDR 484-ball BGA Pinout (Top View)[11]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21 22
DNU DNU
DNU DNU
DNU DNU
DNU DNU
DNU DNU
DNU DNU
DNU DNU
DNU DNU
DNU
DNU
VSS
VSS
DNU
DNU
VSS
VSS
VSS
DNU
DNU
DNU
VSS
DNU
DNU
DNU
CQ1L
DNU
DNU
DNU
CQ1L
DNU
DNU
DNU
VSS
DQ15L
DQ16L
DQ17L
LOWSPDL
DQ12L
DQ9L
DQ9R
DQ12R
DQ15R
DQ16R
DNU
DNU
DNU
DNU
DNU
DNU
DNU
CQ1R
DNU
DNU
DNU
CQ1R
DNU
DNU
DNU
VSS
DNU
DNU
VSS
VSS
VSS
DNU
DNU
VSS
VSS
A
B
C
D
E
DQ13L DQ10L DQ10R DQ13R
DQ14L
DQ11L DQ11R DQ14R
[12]
DQ17R
PORTSTD0L
PORTSTD1L
ZQ0L
BUSYL CNTINTL
DNU DNU VDDIOL
VSS VDDIOL VDDIOR VDDIOR VDDIOR VDDIOR VTTL
VTTL
VTTL
VDDIOL VDDIOL VDDIOL VDDIOL DNU
VDDIOR DNU DNU
DNU DNU
A0L A1L
A2L A3L
CE1L
RETL
WRPL
CE0L VDDIOL VDDIOL VDDIOR VDDIOR VDDIOR VCORE VCORE VCORE VCORE VDDIOL VDDIOL VDDIOL VDDIOR VDDIOR CE0R
CE1R
RETR
DNU DNU
A1R A0R
F
BE1L VDDIOL VDDIOL VREFL
DNU VDDIOL VDDIOL VSS
DNU VDDIOL VDDIOL VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VREFR VDDIOR VDDIOR BE1R
VSS VDDIOR VDDIOR DNU
G
H
J
WRPR A3R A2R
A4L A5L READYL
VSS VDDIOR VDDIOR DNU READYR A5R A4R
[12]
[12]
A6L A7L ZQ1L
DNU
OEL
DNU
VTTL VCORE
VTTL VCORE
VTTL VCORE
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VCORE VDDIOR DNU
ZQ1R
A7R A6R
A9R A8R
A11R A10R
K
L
A8L A9L
CL
VCORE VTTL
VCORE VTTL
VCORE VTTL
OER
DNU
DNU
CR
A10L A11L
VSS
VSS
M
N
P
A12L A13L ADSL
CNT/MSKL
DNU VDDIOL VCORE
ADSR A13R A12R
CNT/MSKR
A15R A14R
A14L A15L
DNU VDDIOL VDDIOL VSS
VSS VDDIOR VDDIOR DNU
VSS VDDIOR VDDIOR BE0R CNTENR A17R A16R
A16L A17L CNTENL BE0L VDDIOL VDDIOL VSS
A18L A19L CNTRSTL INTL VDDIOL VDDIOL VREFL
R
T
CNTRSTR
R/WR
VREFR VDDIOR VDDIOR INTR
A19R A18R
DNU A20R
A20L DNU
R/WL
CQENL VDDIOL VDDIOL VDDIOR VDDIOR VDDIOR VCORE VCORE VCORE VCORE VDDIOL VDDIOL VDDIOL VDDIOR VDDIOR CQENR
U
V
DNU DNU FTSELL VDDIOL DNU VDDIOR VDDIOR VDDIOR VDDIOR
VTTL
VTTL
VTTL
VDDIOL VDDIOL VDDIOL VDDIOL VDDIOR TRST VDDIOR FTSELR DNU DNU
[12]
PORTSTD1R
PORTSTD0R
LOWSPDR
DQ8R
DNU DNU
DNU DNU
DNU DNU
DNU DNU
VSS
VSS
DNU
DNU
MRST
VSS
VSS
DNU
DNU
DNU
CQ0L
DNU
DNU
DNU
CQ0L
DNU
DNU
DNU
DNU
DNU
DNU
DNU
CNTINTR BUSYR ZQ0R
VSS
DNU
DNU
DNU
CQ0R
DNU
DNU
DNU
CQ0R
DNU
DNU
DNU
VSS
DNU
DNU
DNU
TDI
TDO
TCK
DNU
DNU
DNU DNU
DNU DNU
DNU DNU
DNU DNU
W
Y
DQ8L
DQ7L
DQ6L
DQ5L
DQ4L
DQ3L
DQ2L
DQ1L
DQ0L
DQ2R
DQ5R
DQ4R
DQ3R
TMS
DNU
DNU
DNU
DNU
DQ1R
DQ0R
DQ7R
AA
AB
DQ6R
Notes
11. Use this pinout only for device CYD36S18V18 of the FullFlex18 family.
12. Leave this ball unconnected to disable VIM.
Document Number: 38-06082 Rev. *O
Page 6 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Figure 4. FullFlex36 SDR 256-ball BGA (Top View)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
DQ32L
DQ30L
DQ28L
DQ26L
DQ24L
DQ22L
DQ20L
DQ18L
DQ18R
DQ20R
DQ22R
DQ24R
DQ26R
DQ28R
DQ30R
DQ32R
A
B
C
D
E
F
DQ33L
DQ34L
A0L
DQ31L
DQ35L
A1L
DQ29L
RETL
DQ27L
INTL
DQ25L
CQ1L
DQ23L
CQ1L
LOWSPDL
VDDIOL
VSS
DQ21L
DNU
DQ19L
TRST
VTTL
VCORE
VSS
DQ19R
MRST
VTTL
VCORE
VSS
DQ21R
DQ23R
CQ1R
LOWSPDR
VDDIOR
VSS
DQ25R
CQ1R
DQ27R
INTR
DQ29R
RETR
DQ31R
DQ35R
A1R
DQ33R
DQ34R
A0R
[13]
ZQ0R
VSS
WRPL
CE0L
VREFL
CE1L
FTSELL
VDDIOL
VDDIOL
VSS
FTSELR
VDDIOR
VDDIOR
VDDIOR
VCORE
VCORE
VDDIOR
VDDIOR
VDDIOR
VREFR
CE1R
WRPR
CE0R
A2L
A3L
VDDIOL
VSS
VDDIOR
VSS
A3R
A2R
A4L
A5L
CNTINTL
BUSYL
CL
BE3L
BE3R
CNTINTR
BUSYR
CR
A5R
A4R
[13]
A6L
A7L
BE2L
ZQ0L
VSS
VSS
VSS
VSS
VSS
VSS
BE2R
A7R
A6R
G
H
J
A8L
A9L
VTTL
VCORE
VCORE
VDDIOL
VDDIOL
VDDIOL
VSS
VSS
VSS
VSS
VSS
VSS
VTTL
A9R
A8R
A10L
A12L
A14L
A11L
A13L
A15L
VSS
PORTSTD1L
BE1L
VSS
VSS
VSS
VSS
VSS
VSS
PORTSTD1R
BE1R
VSS
A11R
A13R
A15R
A10R
A12R
A14R
OEL
VSS
VSS
VSS
VSS
VSS
VSS
OER
K
L
ADSL
BE0L
VSS
VSS
VSS
VSS
VSS
VSS
BE0R
ADSR
[16]
[15]
[15]
[16]
A16L
A17L
R/WL
CQENL
VREFL
CNTRSTL
DQ9L
VDDIOL
VDDIOL
DNU
VCORE
VTTL
TMS
VCORE
VTTL
TDO
VDDIOR
DNU
VDDIOR
CQENR
VREFR
CNTRSTR
DQ9R
R/WR
A17R
A16R
M
N
P
R
T
[14]
[14]
A18L
DNU
CNT/MSKL
CNTENL
DQ11L
DQ10L
PORTSTD0L READYL
READYR PORTSTD0R
CNT/MSKR
CNTENR
DQ11R
DQ10R
DNU
A18R
DQ16L
DQ15L
DQ14L
DQ17L
DQ13L
DQ12L
CQ0L
DQ7L
DQ6L
CQ0L
DQ5L
DQ4L
TCK
TDI
CQ0R
DQ5R
DQ4R
CQ0R
DQ7R
DQ6R
DQ17R
DQ13R
DQ12R
DQ16R
DQ15R
DQ14R
DQ3L
DQ2L
DQ1L
DQ0L
DQ1R
DQ0R
DQ3R
DQ2R
DQ8L
DQ8R
Notes
13. Leave this ball unconnected to disable VIM.
14. Leave this ball unconnected for CYD09S36V18 and CYD02S36V18.
15. Leave this ball unconnected for CYD02S36V18.
16. Leave this ball unconnected for CYD02S36V18.
Document Number: 38-06082 Rev. *O
Page 7 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Figure 5. FullFlex18 SDR 256-ball BGA (Top View)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
DNU
DNU
DNU
DQ17L
DQ16L
DQ13L
DQ12L
DQ9L
DQ9R
DQ12R
DQ13R
DQ16R
DQ17R
DNU
DNU
DNU
A
B
C
D
E
F
DNU
DNU
A0L
DNU
DNU
A1L
DNU
RETL
DNU
INTL
DQ15L
CQ1L
DQ14L
CQ1L
LOWSPDL
VDDIOL
VSS
DQ11L
DNU
DQ10L
TRST
VTTL
VCORE
VSS
DQ10R
MRST
VTTL
VCORE
VSS
DQ11R
DQ14R
CQ1R
LOWSPDR
VDDIOR
VSS
DQ15R
CQ1R
DNU
INTR
DNU
RETR
WRPR
CE0R
CNTINTR
BUSYR
CR
DNU
DNU
A1R
DNU
DNU
A0R
[17]
ZQ0R
VSS
WRPL
CE0L
VREFL
CE1L
FTSELL
VDDIOL
VDDIOL
VSS
FTSELR
VDDIOR
VDDIOR
VDDIOR
VCORE
VCORE
VDDIOR
VDDIOR
VDDIOR
VREFR
CE1R
A2L
A3L
VDDIOL
VSS
VDDIOR
VSS
A3R
A2R
A4L
A5L
CNTINTL
BUSYL
CL
DNU
DNU
A5R
A4R
[17]
A6L
A7L
DNU
ZQ0L
VSS
VSS
VSS
VSS
VSS
VSS
DNU
A7R
A6R
G
H
J
A8L
A9L
VTTL
VCORE
VCORE
VDDIOL
VDDIOL
VDDIOL
VSS
VSS
VSS
VSS
VSS
VSS
VTTL
A9R
A8R
A10L
A12L
A14L
A16L
A11L
A13L
A15L
A17L
VSS
PORTSTD1L
BE1L
VSS
VSS
VSS
VSS
VSS
VSS
PORTSTD1R
BE1R
VSS
A11R
A13R
A15R
A17R
A10R
A12R
A14R
A16R
OEL
VSS
VSS
VSS
VSS
VSS
VSS
OER
K
L
ADSL
R/WL
BE0L
VSS
VSS
VSS
VSS
VSS
VSS
BE0R
ADSR
R/WR
CQENL
VREFL
CNTRSTL
DNU
VDDIOL
VDDIOL
DNU
VCORE
VTTL
TMS
VCORE
VTTL
TDO
VDDIOR
DNU
VDDIOR
CQENR
VREFR
CNTRSTR
DNU
M
N
P
R
T
[19]
[18]
[18]
[19]
A18L
A19L
CNT/MSKL
CNTENL
DNU
PORTSTD0L READYL
READYR PORTSTD0R
CNT/MSKR A19R
A18R
DNU
DNU
DNU
DNU
DNU
DNU
CQ0L
DQ6L
DQ7L
CQ0L
DQ5L
DQ4L
TCK
TDI
CQ0R
DQ5R
DQ4R
CQ0R
DQ6R
DQ7R
CNTENR
DNU
DNU
DNU
DNU
DNU
DQ2L
DQ3L
DQ1L
DQ0L
DQ1R
DQ0R
DQ2R
DQ3R
DNU
DNU
DNU
DQ8L
DQ8R
DNU
Notes
17. Leave this ball unconnected to disable VIM.
18. Leave this ball unconnected for CYD09S18V18.
19. Leave this ball unconnected for CYD04S18V18.
Document Number: 38-06082 Rev. *O
Page 8 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Selection Guide
Parameter
-200
200
-167
167
Unit
MHz
ns
[21]
fMAX
Maximum access time (clock to data)
Typical operating current ICC
3.3
4.0
800[20]
210[20]
700[20]
210[20]
mA
mA
Typical standby current for ISB3 (both ports CMOS level)
Pin Definitions
Left Port
A[20:0]L
Right Port
A[20:0]R
Description
Address inputs.[22]
DQ[71:0]L
BE[7:0]L
DQ[71:0]R
BE[7:0]R
Data bus input and output.[23]
Byte select inputs.[24] Asserting these signals enables read and write operations to the
corresponding bytes of the memory array.
BUSYL
BUSYR
Port busy output. When there is an address match and both chip enables are active for both
ports, an external BUSY signal is asserted on the fifth clock cycles from when the collision occurs.
CL
CR
Clock signal. Maximum clock input rate is fMAX
Active LOW chip enable input.
.
CE0L
CE1L
CQENL
CQ0L
CE0R
CE1R
CQENR
CQ0R
Active HIGH chip enable input.
Echo clock enable input. Assert HIGH to enable echo clocking on respective port.
Echo clock signal output for DQ[35:0] for FullFlex72 devices. Echo clock signal output for
DQ[17:0] for FullFlex36 devices. Echo clock signal output for DQ[8:0] for FullFlex18 devices.
CQ0L
CQ0R
Inverted echo clock signal output for DQ[35:0] for FullFlex72 devices. Inverted echo clock
signal output for DQ[17:0] for FullFlex36 devices. Inverted echo clock signal output for DQ[8:0]
for FullFlex18 devices.
CQ1L
CQ1L
CQ1R
CQ1R
Echo clock signal output for DQ[71:36] for FullFlex72 devices. Echo clock signal output for
DQ[35:18] for FullFlex36 devices. Echo clock signal output for DQ[17:9] for FullFlex18 devices.
Inverted echo clock signal output for DQ[71:36] for FullFlex72 devices. Inverted echo clock
signal output for DQ[35:18] for FullFlex36 devices. Inverted echo clock signal output for DQ[17:9]
for FullFlex18 devices.
ZQ[1:0]L
ZQ[1:0]R
VIM output impedance matching input.[25] To use, connect a calibrating resistor between ZQ
and ground. The resistor must be five times larger than the intended line impedance driven by
the dual port. Assert HIGH or leave DNU to disable VIM.
OEL
INTL
OER
INTR
Output enable input. This asynchronous signal must be asserted LOW to enable the DQ data
pins during read operations.
Mailbox interrupt flag output. The mailbox permits communications between ports. The upper
two memory locations are used for message passing. INTL is asserted LOW when the right port
writes to the mailbox location of the left port, and vice versa. An interrupt to a port is deasserted
HIGH when it reads the contents of its mailbox.
Notes
20. For 18 Mbit x72 commercial configuration only, refer to Electrical Characteristics on page 19 for complete information.
21. SDR mode with two pipelined stages.
22. The CYD36S18V18 device has 21 address bits. The CYD36S36V18 and CYD18S18V18 devices have 20 address bits. The CYD36S72V18, CYD18S36V18, and
CYD09S18V18 devices have 19 address bits. The CYD18S72V18 and CYD09S36V18 devices have 18 address bits. The CYD09S72V18 device has 17 address
bits. The CYD02S36V18 has 16 address bits.
23. The FullFlex72 family of devices has 72 data lines. The FullFlex36 family of devices has 36 data lines. The FullFlex18 family of devices has 18 data lines.
24. The FullFlex72 family of devices has eight byte enables. The FullFlex36 family of devices has four byte enables. The FullFlex18 family of devices has two byte enables.
25. The pin ZQ[1] is applicable only for 36 Mbit devices. This pin is DNU for 18 Mbit and lower density devices.
Document Number: 38-06082 Rev. *O
Page 9 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Pin Definitions (continued)
Left Port
LowSPDL
Right Port
LowSPDR
Description
Port low speed select input. Assert this pin LOW to disable the DLL. In flow through mode, this
pin needs to be asserted low.
[26]
[26]
PORTSTD[1:0]L
PORTSTD[1:0]R
Port clock/Address/Control/Data/Echo clock/I/O standard select input. Assert these pins
LOW/LOW for LVTTL, LOW/HIGH for HSTL, HIGH/LOW for 2.5 V LVCMOS, and HIGH/HIGH
for 1.8 V LVCMOS, respectively. These pins are driven by VTTL referenced levels.
R/WL
R/WR
Read/Write enable input. Assert this pin LOW to write to, or HIGH to read from the dual port
memory array.
READYL
READYR
Port DLL ready output. This signal is asserted LOW when the DLL and variable impedance
matching circuits complete calibration. This is a wired OR capable output.
CNT/MSKL
ADSL
CNT/MSKR
ADSR
Port counter/Mask select input. Counter control input.
Port counter address load strobe input. Counter control input.
Port counter enable input. Counter control input.
Port counter reset input. Counter control input.
CNTENL
CNTRSTL
CNTINTL
CNTENR
CNTRSTR
CNTINTR
Port counter interrupt output. This pin is asserted LOW one cycle before the unmasked portion
of the counter is incremented to all “1s”.
WRPL
RETL
WRPR
RETR
Port counter wrap input. When the burst counter reaches the maximum count, on the next
counter increment WRP is set LOW to load the unmasked counter bits to 0. It is set HIGH to load
the counter with the value stored in the mirror register.
Port counter retransmit input. Assert this pin LOW to reload the initial address for repeated
access to the same segment of memory.
VREFL
VREFR
VDDIOR
FTSELR
Port external HSTL IO reference input. This pin is left DNU when HSTL is not used.
Port data IO power supply.
VDDIOL
FTSELL
Port flow through mode select input. Assert this pin LOW to select flow through mode. Assert
this pin HIGH to select Pipelined mode.
MRST
Master reset input. MRST is an asynchronous input signal and affects both ports. Asserting
MRST LOW performs all of the reset functions as described in the text. A MRST operation is
required at power up. This pin is driven by a VDDIOL referenced signal.
TMS
TDI
JTAG test mode select input. It controls the advance of JTAG TAP state machine. State
machine transitions occur on the rising edge of TCK. Operation for LVTTL or 2.5 V LVCMOS.
JTAG test data input. Data on the TDI input is shifted serially into selected registers. Operation
for LVTTL or 2.5 V LVCMOS.
TRST
TCK
JTAG reset input. Operation for LVTTL or 2.5 V LVCMOS.
JTAG test clock input. Operation for LVTTL or 2.5 V LVCMOS.
TDO
JTAG test data output. TDO transitions occur on the falling edge of TCK. TDO is normally
tri-stated except when captured data is shifted out of the JTAG TAP. Operation for LVTTL or 2.5 V
LVCMOS.
VSS
Ground inputs.
VCORE
VTTL
Device core power supply.
LVTTL power supply.
Note
26. PORTSTD[1:0] and PORTSTD[1:0] have internal pull-down resistors.
L
R
Document Number: 38-06082 Rev. *O
Page 10 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
LowSPD pins are used to reset the DLLs for a single port
independent of all other circuitry. MRST is used to reset all DLLs
on the chip. For more information on DLL lock and reset time,
see Master Reset on page 18.
Selectable IO Standard
The FullFlex device families offer the option to choose one of the
four port standards for the device. Each port independently
selects standards from single ended HSTL class I, single ended
LVTTL, 2.5 V LVCMOS, or 1.8 V LVCMOS. The selection of the
standard is determined by the PORTSTD pins for each port.
These pins must be connected to an LVTTL power suppy. This
determines the input clock, address, control, data, and Echo
clock standard for each port as shown in Table 1.
Echo Clocking
As the speed of data increases, on-board delays caused by
parasitics make it extremely difficult to provide accurate clock
trees. To counter this problem, the FullFlex families incorporate
Echo Clocks. Echo Clocks are enabled on a per port basis. The
dual port receives input clocks that are used to clock in the
address and control signals for a read operation. The dual port
retransmits the input clocks relative to the data output. The
buffered clocks are provided on the CQ1/CQ1 and CQ0/CQ0
outputs. Each port has a pair of Echo clocks. Each clock is
associated with half the data bits. The output clock matches the
corresponding ports IO configuration.
Table 1. Port Standard Selection
PORTSTD1
VSS
PORTSTD0
VSS
I/O Standard
LVTTL
VSS
VTTL
HSTL
VTTL
VSS
2.5 V LVCMOS
1.8 V LVCMOS
VTTL
VTTL
To enable echo clock outputs, tie CQEN HIGH. To disable echo
clock outputs, tie CQEN LOW.
Clocking
Figure 6. SDR Echo Clock Delay
Separate clocks synchronize the operations on each port. Each
port has one clock input C. In this mode, all the transactions on
the address, control, and data are on the C rising edge. All
transactions on the address, control, data input, output, and byte
enables occur on the C rising edge.
Input Clock
Data Out
Table 2. Data Pin Assignment
Echo Clock
Echo Clock
BE Pin Name
BE[7]
Data Pin Name
DQ[71:63]
DQ[62:54]
DQ[53:45]
DQ[44:36]
DQ[35:27]
DQ[26:18]
DQ[17:9]
Deterministic Access Control
BE[6]
Deterministic Access Control is provided for ease of design. The
circuitry detects when both ports access the same location and
provides an external BUSY flag to the port on which data is
corrupted. The collision detection logic saves the address in
conflict (Busy Address) to a readable register. In the case of
multiple collisions, the first busy address is written to the busy
address register.
BE[5]
BE[4]
BE[3]
BE[2]
BE[1]
If both ports access the same location at the same time and only
one port is doing a write, if tCCS is met, then the data written to
and read from the address is valid data. For example, if the right
port is reading and the left port is writing and the left ports clock
meets tCCS, then the data read from the address by the right port
is the old data. In the same case, if the right ports clock meets
BE[0]
DQ[8:0]
Selectable Pipelined or Flow through Mode
To meet data rate and throughput requirements, the FullFlex
families offer selectable pipelined or flow through mode. Echo
clocks are not supported in flow through mode and the DLL must
be disabled.
t
CCS, then the data read out of the address from the right port is
the new data. In the above case, if tCCS is violated by the either
ports clock with respect to the other port and the right port gets
the external BUSY flag, the data from the right port is corrupted.
Table 3 on page 12 shows the tCCS timing that must be met to
guarantee the data.
Flow through mode is selected by the FTSEL pin. Strapping this
pin HIGH selects pipelined mode. Strapping this pin LOW selects
flow through mode.
Table 4 on page 12 shows that, in the case of the left port writing
and the right port reading, when an external BUSY flag is
asserted on the right port, the data read out of the device is not
guaranteed.
DLL
The FullFlex familes of devices have an on-chip DLL. Enabling
the DLL reduces the clock to data valid (tCD) time enabling more
setup time for the receiving device. In flow through mode, the
DLL must be disabled. This is selectable by strapping LowSPD
low.
The value in the busy address register is read back to the
address lines. The required input control signals for this function
are shown in Table 7 on page 14. The value in the busy address
register is read out to the address lines tCA after the same
amount of latency as a data read operation. After an initial
address match, the BUSY flag is asserted and the address under
contention is saved in the busy address register. All the following
Whenever the operating frequency is altered beyond the Clock
Input Cycle to Cycle Jitter specification, reset the DLL, followed
by 1024 clocks before any valid operation.
Document Number: 38-06082 Rev. *O
Page 11 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
address matches enable to generate the BUSY flag. However,
none of the addresses are saved into the busy address register.
When a busy readback is performed, the address of the first
match that happens at least two clocks cycles after the busy
readback is saved into the busy address register.
Table 3. tCCS Timing for All Operating Modes
Port A—Early Arriving Port
Port B—Late Arriving Port
tCCS
Unit
Mode
Active Edge
Mode
Active Edge
C Rise to Opposite C Rise Setup Time for Non Corrupt Data
SDR
C
SDR
C
tCYC(min) – 0.5
ns
Table 4. Deterministic Access Control Logic
Left Port
Read
Right Port
Read
Left Clock
Right Clock
BUSYL
BUSYR
Description
No collision
X
X
H
H
H
H
H
H
H
H
H
H
L
H
H
H
H
L
Write
Read
> tCCS
0
0
> tCCS
0
Read OLD data
Read NEW data
Read OLD data
< tCCS
Data not guaranteed
Read NEW data
Data Not guaranteed
Read NEW data
Read OLD data
0
< tCCS
H
L
Read
Write
Write
> tCCS
0
0
> tCCS
0
H
H
H
H
H
H
L
< tCCS
Read NEW data
Data Not guaranteed
Read OLD data
0
< tCCS
H
L
Data not guaranteed
Array data corrupted
Write
0
0
> –tCCS & < tCCS
L
> tCCS
0
L
H
L
Array stores right port data
Array stores left port data
> tCCS
H
Table 5. Variable Impedance Matching Parameters
Variable Impedance Matching
Parameter
RQ value
Min
100
20
–
Max
275
55
Unit
Tolerance
Each port contains a variable impedance matching circuit to set
the impedance of the IO driver to match the impedance of the
on-board traces. The impedance is set for all outputs except
JTAG and is done by port. To take advantage of the VIM feature,
connect a calibrating resistor (RQ) that is five times the value of
the intended line impedance from the ZQ[1:0][27] pin to VSS. The
output impedance is then adjusted to account for drifts in supply
voltage and temperature every 1024 clock cycles. If a port’s clock
is suspended, the VIM circuit retains its last setting until the clock
is restarted. On restart, it then resumes periodic adjustment. In
the case of a significant change in device temperature or supply
voltage, recalibration happens every 1024 clock cycles. A master
reset initializes the VIM circuitry. Table 5 shows the VIM
parameters and Table 6 describes the VIM operation modes.
±2%
±15%
–
Output impedance
Reset time
1024 Cycles
1024 Cycles
Update time
–
–
Table 6. Variable Impedance Matching Operation
RQ Connection Output Configuration
100 –275 to VSS Output driver impedance = RQ/5 ± 15%
at Vout = VDDIO/2
ZQto VDDIO
VIM disabled. Rout < 20 at Vout =
VDDIO/2
To disable VIM, connect the ZQ pin to VDDIO of the relative
supply for the IOs before a Master Reset.
Note
27. The pin ZQ[1] is applicable only for 36 Mbit devices. This pin is DNU for 18 Mbit and lower density devices.
Document Number: 38-06082 Rev. *O
Page 12 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Address Counter and Mask Register Operations [28]
Counter Load Operation [28]
Each port of the FullFlex family contains a programmable burst
address counter. The burst counter contains four registers: a
counter register, a mask register, a mirror register, and a busy
address register.
For both non-burst and burst read or write accesses, the external
address is loaded through counter load operation as shown in
Table 7 on page 14. The address counter and mirror registers are
loaded with the address value presented on the address lines.
This value ranges from 0 to 1FFFFF.
The counter register contains the address used to access the
RAM array. It is changed only by the master reset (MRST),
counter reset, counter load, retransmit, and counter increment
operations.
Mask Load Operation [28]
The mask register is loaded with the address value presented on
the address bus. This value ranges from 0 to 1FFFFF though not
all values permit correct increment operations. Permitted values
are in the form of 2n–1, 2n–2, or 2n–4. The counter register is only
segmented up to three regions. From the most significant bit to
the least significant bit, permitted values have zero or more 0s,
one or more 1s, and the least significant two bits are 11, 10, or
00. Thus 1FFFFE, 07FFFF, and 003FFC are permitted values
but 02FFFF, 003FFA, and 07FFE4 are not.
The mask register value affects the counter increment and
counter reset operations by preventing the corresponding bits of
the counter register from changing. It also affects the counter
interrupt output (CNTINT). The mask register is only changed by
mask reset, mask load, and MRST. The mask load operation
loads the value of the address bus into the mask register. The
mask register defines the counting range of the counter register.
The mask register is divided into two or three consecutive
regions. Zero or more 0s define the masked region and one or
more 1s define the unmasked portion of the counter register. The
counter register may be divided up to three regions. The region
containing the least significant bits must be no more than two 0s.
Bits one and zero may be 10 respectively, masking the least
significant counter bit and causing the counter to increment by
two instead of one. If bits one and zero are 00, the two least
significant bits are masked and the counter increments by four
instead of one. For example, in the case of a 256 K × 72
configuration, a mask register value of 003FC divides the mask
register into three regions. With bit 0 being the least significant
bit and bit 17 being the most significant bit, the two least
significant bits are masked, the next eight bits are unmasked,
and the remaining bits are masked.
Counter Readback Operation
The internal value of the counter register is read out on the
address lines. The address is valid tCA after the selected number
of latency cycles configured by FTSEL. The data bus (DQ) is
tri-stated on the cycle that the address is presented on the
address lines. Figure 7 on page 16 shows a block diagram of this
logic.
Mask Readback Operation
The internal value of the mask register is read out on the address
lines. The address is valid tCA after the selected number of
latency cycles configured by FTSEL. The data bus (DQ) is
tri-stated on the cycle that the address is presented on the
address lines. Figure 7 on page 16 shows a block diagram of the
operation.
The mirror register reloads a counter register on retransmit
operations (see Retransmit on page 15) and wrap functions (see
Counter Interrupt on page 15 below). The last value loaded into
the counter register is stored in the mirror register. The mirror
register is only changed by master reset (MRST), counter reset,
and counter load.
Counter Reset Operation
All unmasked bits of the counter and mirror registers are reset to
‘0’. All masked bits remain unchanged. A mask reset followed by
a counter reset resets the counter and mirror registers to 00000.
Table 7 on page 14 summarizes the operations of these registers
and the required input control signals. All signals except MRST
are synchronized to the ports clock.
Mask Reset Operation
The mask register is reset to all 1s, that unmasks every bit of the
burst counter.
Note
28. The CYD36S18V18 device has 21 address bits. The CYD36S36V18 and CYD18S18V18 devices have 20 address bits. The CYD36S72V18, CYD18S36V18, and
CYD09S18V18 devices have 19 address bits. The CYD18S72V18 and CYD09S36V18 devices have 18 address bits. The CYD09S72V18 device has 17 address bits.
The CYD02S36V18 has 16 address bits.
Document Number: 38-06082 Rev. *O
Page 13 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Table 7. Burst Counter and Mask Register Control Operations
The burst counter and mask register control operation for any port follows. [29, 30]
C
MRST CNTRST CNT/MSK CNTEN ADS RET
Operation
Master reset
Description
X
L
X
X
X
X
X
Reset address counter to all 0s, mask
register to all 1s, and busy address to all 0s.
H
L
H
X
X
X
Counter reset
Mask reset
Reset counter and mirror unmasked portion
to all 0s.
H
H
L
L
X
L
X
L
X
X
Reset mask register to all 1s.
H
H
Counter
load
for Load burst counter and mirror with external
burst/external address address value presented on address lines.
load for non-burst
H
H
L
L
L
X
Mask load
Load mask register with value presented on
the address lines.
H
H
H
H
H
H
H
H
H
L
L
H
H
H
L
H
H
Retransmit
Load counter with value in the mirror register.
Internally increment address counter value.
Counter increment
Counter hold
H
Constantly hold the address value for
multiple clock cycles.
H
H
H
H
H
H
H
L
L
H
H
H
L
L
H
H
L
Counter readback
Mask readback
Read out counter internal value on address
lines.
Read out mask register value on address
lines.
H
Busy address readback Read out first busy address after last busy
address readback.
H
H
H
H
H
H
H
H
H
H
L
L
L
H
L
X
L
Reserved
Reserved
Reserved
Reserved
Reserved
H
H
H
H
L
H
L
H
L
H
H
H
L
Notes
29. “X” = Don’t Care, “H” = HIGH, “L” = LOW.
30. Counter operation and mask register operation is independent of chip enables.
Document Number: 38-06082 Rev. *O
Page 14 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Increment Operation[31]
mirror register stores the address counter value last loaded.
While RET is asserted low, the counter continues to wrap back
to the value in the mirror register independent of the state of
WRP.
After the address counter is initially loaded with an external
address, the counter can internally increment the address value
and address the entire memory array. Only the unmasked bits of
the counter register are incremented. For a counter bit to
change, the corresponding bit in the mask register must be 1. If
the two least significant bits of the mask register are 11, the burst
counter increments by one. If the two least significant bits are 10,
the burst counter increments by two, and if they are 00, the burst
counter increments by four. If all unmasked counter bits are
incremented to 1 and WRP is deasserted, the next increment l
wraps the counter back to the initially loaded value. The cycle
before the increment that results in all unmasked counter bits to
become 1s, a counter interrupt flag (CNTINT) is asserted if the
counter is incremented again. This increment causes the counter
to reach its maximum value and the next increment returns the
counter register to its initial value that was stored in the mirror
register if WRP is deasserted. If WRP is asserted, the unmasked
portion of the counter is filled with 0 instead. The example shown
Counter Interrupt
The counter interrupt (CNTINT) is asserted LOW one clock cycle
before an increment operation that results in the unmasked
portion of the counter register being all 1s. It is deasserted by
counter reset, counter load, counter increment, mask reset,
mask load, and MRST.
Counting by Two
When the two least significant bits of the mask register are 10,
the counter increments by two.
Counting by Four
When the two least significant bits of the mask register are 00,
the counter increments by four.
in Figure
8 on page 17 shows an example of the
CYDD36S18V18 device with the mask register loaded with a
mask value of 00007F unmasking the seven least significant bits.
Setting the mask register to this value enables the counter to
access the entire memory space. The address counter is then
loaded with an initial value of 000005 assuming WRP is
deasserted. The masked bits, the seventh address through the
twenty-first address, do not increment in an increment operation.
The counter address starts at address 000005 and increments
its internal address value until it reaches the mask register value
of 00007F. The counter wraps around the memory block to
location 000005 at the next count. CNTINT is issued when the
counter reaches the maximum –1 count.
Mailbox Interrupts
Use the upper two memory locations for message passing and
permit communications between ports. Table 8 on page 17
shows the interrupt operation for both ports. The highest memory
location is the mailbox for the right port and the maximum
address – 1 is the mailbox for the left port.
When one port writes to the other port’s mailbox, the INT flag of
the port that the mailbox belongs to is asserted LOW. The INT
flag remains asserted until the mailbox location is read by the
other port. When a port reads its mailbox, the INT flag is
deasserted high after one cycle of latency with respect to the
input clock of the port to which the mailbox belongs and is
independent of OE.
Hold Operation
The value of all three registers is constantly maintained
unchanged for an unlimited number of clock cycles. This
operation is useful in applications where wait states are needed
or when address is available a few cycles ahead of data in a
shared bus interface.
As shown in Table 8 on page 17, to set the INTR flag, a write
operation by the left port to address 1FFFFF asserts INTR LOW.
A valid read of the 1FFFFF location by the right port resets INTR
HIGH after one cycle of latency with respect to the right port’s
clock. You must activate at least one byte enable to set or reset
the mailbox interrupt.
Retransmit
Retransmit enables repeated access to the same block of
memory without the need to reload the initial address. An internal
Note
31. The CYD36S18V18 device has 21 address bits. The CYD36S36V18 and CYD18S18V18 devices have 20 address bits. The CYD36S72V18, CYD18S36V18, and
CYD09S18V18 devices have 19 address bits. The CYD18S72V18 and CYD09S36V18 devices have 18 address bits. The CYD09S72V18 device has 17 address bits.
The CYD02S36V18 has 16 address bits.
Document Number: 38-06082 Rev. *O
Page 15 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Figure 7. Counter, Mask, and Mirror Logic Block Diagram
Figure 7 shows the counter, mask, and mirror logic block diagram. [32]
CNT/MSK
CNTEN
A
Decode
Logic
CNTRST
RET
MRST
A
C
Mask
Register
Counter/
Address
Register
RAM
Array
Address
Decode
Load/Increment
20
20
From
Address
Lines
Counter
Mirror
To Readback
and Address
Decode
1
0
1
0
From
Mask
Register
Increment
Logic
20
Wrap
20
20
20
From
Mask
Bit 0
and 1
From
Counter
+1
+2
+4
Wrap
Detect
Wrap
1
0
20
1
0
To Coun-
ter
Note
32. The CYD36S18V18 device has 21 address bits. The CYD36S36V18 and CYD18S18V18 devices have 20 address bits. The CYD36S72V18, CYD18S36V18, and
CYD09S18V18 devices have 19 address bits. The CYD18S72V18 and CYD09S36V18 devices have 18 address bits. The CYD09S72V18 device has 17 address bits.
The CYD02S36V18 has 16 address bits.
Document Number: 38-06082 Rev. *O
Page 16 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Figure 8. Programmable Counter-Mask Register Operation with WRP deasserted
Figure 8 shows the programmable counter-mask operation with WRP deasserted. [36, 38]
CNTINT
Example:
Load
Counter-Mask
Register = 00007F
H
0
0
0s
1
1
1
1
1
1
1
0
220 219
Masked Address
26 25 24 23 22 21 20
27
Mask
Register
LSB
Unmasked Address
Load
Address
Counter = 000005
H
L
X
X
Xs
Xs
Xs
0
0
0
0
1
0
1
X
X
220 219
26 25 24 23 22 21 20
Address
Counter
LSB
27
27
27
Max
Address
Value
X
X
1
1
1
1
1
1
1
220 219
26 25 24 23 22 21 20
Max + 1
Address
Value
H
X
X
0
0
0
0
1
0
1
X
220 219
26 25 24 23 22 21 20
Table 8. Interrupt Operation Example
Table 8 shows the interrupt operation example. [33, 34, 35, 37, 38]
Left Port
Function
Right Port
R/WL
CEL
L
A0L–20L
INTL
X
R/WR
CER
X
A0R–20R
INTR
L
Set Right INTR Flag
Reset Right INTR Flag
Set Left INTL Flag
L
X
X
H
Max Address
X
H
L
X
X
X
X
L
Max Address
Max Address–1
X
H
X
X
L
L
X
Reset Left INTL Flag
L
Max Address–1
H
X
X
X
Notes
33. CE is internal signal. CE = LOW if CE = LOW and CE = HIGH. For a single read operation, CE only needs to be asserted once at the rising edge of the C and is
0
1
deasserted after that. Data is out after the following C edge and is tri-stated after the next C edge.
34. OE is “Don’t Care” for mailbox operation.
35. At least one of BE0, BE1, BE2, BE3, BE4, BE5, BE6, or BE7 must be LOW.
36. The “X” in this diagram represents the counter’s upper bits.
37. “X” = Don’t Care, “H” = HIGH, “L” = LOW.
38. The CYD36S18V18 device has 21 address bits. The CYD36S36V18 and CYD18S18V18 devices have 20 address bits. The CYD36S72V18, CYD18S36V18, and
CYD09S18V18 devices have 19 address bits. The CYD18S72V18 and CYD09S36V18 devices have 18 address bits. The CYD09S72V18 device has 17 address bits.
The CYD02S36V18 has 16 address bits.
Document Number: 38-06082 Rev. *O
Page 17 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Master Reset
Table 9. JTAG IDCODE Register Definitions
The FullFlex family of Dual Ports undergoes a complete reset
when MRST is asserted. MRST must be driven by VDDIOL
referenced levels. The MRST is asserted asynchronously to the
clocks and must remain asserted for at least tRS. When asserted
MRST deasserts READY, initializes the internal burst counters,
internal mirror registers, and internal busy addresses to zero. It
also initializes the internal mask register to all 1s. All mailbox
interrupts (INT), busy address outputs (BUSY), and burst
counter interrupts (CNTINT) are deasserted upon master reset.
Additionally, do not release MRST until all power supplies
including VREF are fully ramped and all port clocks and mode
select inputs (LOWSPD, ZQ, CQEN, FTSEL, and PORTSTD)
are valid and stable. This begins calibration of the DLL and VIM
circuits. READY is asserted within 1024 clock cycles. READY is
a wired OR capable output with a strong pull up and weak pull
down. Up to four outputs may be connected together. For faster
pull down of the signal, connect a 250 Ohm resistor to VSS. If
the DLL and VIM circuits are disabled for a port, the port is
operational within five clock cycles. However, the READY is
asserted within 160 clock cycles.
Part Number
CYD36S72V18
CYD36S36V18
CYD36S18V18
CYD18S72V18
CYD18S36V18
CYD18S18V18
CYD09S72V18
CYD09S36V18
CYD09S18V18
CYD02S36V18
Configuration
512 K × 72
1024 K × 36
2048 K × 18
256 K × 72
512 K × 36
1024 K × 18
128 K × 72
256 K × 36
512 K × 18
64 K × 36
Value
0C026069h (×2)
0C023069h
0C024069h
0C025069h
0C026069h
0C027069h
0C028069h
0C029069h
0C02A069h
0C030069h
Table 10. Scan Registers Sizes
Register Name
Instruction
Bit Size
IEEE 1149.1 Serial Boundary Scan (JTAG)
4
1
Bypass
The FullFlex families incorporate an IEEE 1149.1 serial
boundary scan test access port (TAP). The TAP operates using
JEDEC-standard 3.3 V or 2.5 V IO logic levels depending on the
VTTL power supply. It is composed of four input connections and
one output connection required by the test logic defined by the
standard.
Identification
Boundary Scan
32
n[39]
Table 11. Instruction Identification Codes
Instruction
EXTEST
Code
0000
1111
1011
0111
Description
Captures the input and output ring contents. Places the BSR between the TDI and TDO.
Places the BYR between TDI and TDO.
BYPASS
IDCODE
HIGHZ
Loads the IDR with the vendor ID code and places the register between TDI and TDO.
Places BYR between TDI and TDO. Forces all FullFlex72 and FullFlex36 output drivers to a
High Z state.
CLAMP
0100
1000
Controls boundary to 1 or 0. Places BYR between TDI and TDO.
SAMPLE/PRELOAD
RESERVED
Captures the input and output ring contents. Places BSR between TDI and TDO.
All other Other combinations are reserved. Do not use other than the mentioned combinations.
codes
Note
39. Details of the boundary scan length is found in the BSDL file for the device.
Document Number: 38-06082 Rev. *O
Page 18 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Maximum Ratings
Operating Range
Ambient
Temperature
Exceeding maximum ratings may impair the useful life of the
device. User guidelines are not tested.
Range
VCORE
Commercial
0 °C to +70 °C
1.8 V 100 mV
1.5 V 80 mV
Storage temperature............................... –65 °C to + 150 °C
Ambient temperature with
power applied .......................................... –55 °C to + 125 °C
Industrial
–40 °C to +85 °C
1.8 V 100 mV
1.5 V 80 mV
Supply voltage to ground potential ..............–0.5 V to + 4.1 V
DC voltage applied to
outputs in high Z State...................... –0.5 V to VDDIO + 0.5 V
Power Supply Requirements
DC input voltage...............................–0.5 V to VDDIO + 0.5 V
Output current into outputs (LOW) ............................. 20 mA
Static discharge voltage...........................................> 2200 V
(JEDEC JESD8-6, JESD8-B)
Min
Typ
Max
3.6 V
2.7 V
1.9 V
1.9 V
3.6 V
2.7 V
0.95 V
LVTTL VDDIO
2.5 V LVCMOS VDDIO
HSTL VDDIO
3.0 V
2.3 V
1.4 V
1.7 V
3.0 V
2.3 V
0.68 V
3.3 V
2.5 V
1.5 V
1.8 V
3.3 V
2.5 V
0.75 V
Latch-up current .....................................................> 200 mA
1.8 V LVCMOS VDDIO
3.3 V VTTL
2.5 V VTTL
HSTL VREF
Electrical Characteristics
Over the Operating Range
All Speed Bins
Parameter
Description
Configuration
Unit
Min
Typ
Max
VOH
Output HIGH voltage
(VDDIO = Min, IOH = –8 mA)
LVTTL
2.4[40]
–
–
V
(VDDIO = Min, IOH = –4 mA)
(VDDIO = Min, IOH = –4 mA)
(VDDIO = Min, IOH = –6 mA)
(VDDIO = Min, IOH = –4 mA)
HSTL (DC)[41]
HSTL (AC)[41]
2.5 V LVCMOS
1.8 V LVCMOS
LVTTL
VDDIO – 0.4[40]
VDDIO – 0.5[40]
1.7[40]
–
–
–
–
–
–
V
V
V
V
V
–
–
–
VDDIO – 0.45[40]
VOL
Output HIGH voltage
–
0.4[40]
(VDDIO = Min, IOL = 8 mA)
(VDDIO = Min, IOL = 4 mA)
(VDDIO = Min, IOL = 4 mA)
(VDDIO = Min, IOL = 6 mA)
(VDDIO = Min, IOL = 4 mA)
Input HIGH voltage
HSTL(DC)[41]
HSTL (AC)[41]
2.5 V LVCMOS
1.8 V LVCMOS
LVTTL
HSTL(DC)[41]
2.5 V LVCMOS
1.8 V LVCMOS
LVTTL
–
–
–
–
–
–
–
–
–
–
–
–
–
0.4[40]
0.5[40]
0.7[40]
V
V
V
V
V
V
V
V
V
V
V
V
–
–
–
0.45[40]
VIH
2
VDDIO + 0.3
VDDIO + 0.3
VREF + 0.1
1.7
0.65 × VDDIO
VIL
Input LOW voltage
–0.3
–0.3
–
0.8
VREF – 0.1
0.7
HSTL(DC)[41]
2.5 V LVCMOS
1.8 V LVCMOS
–
0.35 × VDDIO
Notes
40. These parameters are met with VIM disabled.
41. The DC specifications are measured under steady state conditions. The AC specifications are measured while switching at speed. AC VIH/VIL in HSTL mode
are measured with 1 V/ns input edge rates.
Document Number: 38-06082 Rev. *O
Page 19 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Electrical Characteristics (continued)
Over the Operating Range
All Speed Bins
Parameter
Description
Configuration
Unit
Max
Min
Typ
Output HIGH voltage
(VDDIO = Min, IOH = –24 mA)
LVTTL
2.7[42]
–
–
V
READY
VOH
(VDDIO = Min, IOH = –12 mA)
(VDDIO = Min, IOH = –12 mA)
(VDDIO = Min, IOH = –15 mA)
(VDDIO = Min, IOH = –12 mA)
HSTL(DC)[43]
HSTL (AC)[43]
2.5 V LVCMOS
1.8 V LVCMOS
LVTTL
VDDIO – 0.4[42]
VDDIO – 0.5[42]
2.0[42]
–
–
–
–
–
–
V
V
V
V
V
–
–
–
VDDIO – 0.45[42]
Output HIGH voltage
–
0.4[42]
READY
VOL
(VDDIO = Min, IO = 0.12 mA)
(VDDIO = Min, IOL = 0.12 mA)
(VDDIO = Min, IOL = 0.12 mA)
(VDDIO = Min, IOL = 0.15 mA)
(VDDIO = Min, IOL = 0.08 mA)
Output leakage current
HSTL(DC)[43]
HSTL (AC)[43]
2.5 V LVCMOS
1.8 V LVCMOS
–
–
–
–
–
–
–
–
0.4[42]
0.5[42]
0.7[42]
0.45[42]
10
V
V
–
V
–
V
IOZ
IIX1
–10
–10
A
A
Input leakage current except
TDI, TMS, MRST, PORTSTD
10
IIX2
IIX3
Input leakage current TDI,
TMS, MRST
–300
–10
–
–
10
A
A
Input leakage current
PORTSTD
300
Notes
42. These parameters are met with VIM disabled.
43. The DC specifications are measured under steady state conditions. The AC specifications are measured while switching at speed. AC VIH/VIL in HSTL mode are
measured with 1 V/ns input edge rates.
Document Number: 38-06082 Rev. *O
Page 20 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Electrical Characteristics
Over the Operating Range
-200
-167
Unit
Parameter
ICC
Description
Configuration
Typ
1440
–
Max
1800
–
Typ
Max
1620
1730
1350
1470
1290
1410
880
930
720
780
690
750
700
740
570
600
580
610
–
Operating current
(VCORE = Max, IOUT = 0 mA)
outputs disabled
512 K × 72 Commercial
Industrial
1280
1330
1050
1110
1000
1060
700
730
570
590
540
570
560
580
470
490
480
500
–
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
1024 K × 36 Commercial
Industrial
1180
–
1500
–
2048 K × 18 Commercial
Industrial
1130
–
1430
–
256 K × 72 Commercial
Industrial
800
820
640
670
610
640
640
660
540
550
550
570
–
980
1030
800
860
770
830
790
830
640
670
660
690
–
512 K × 36 Commercial
Industrial
1024 K × 18 Commercial
Industrial
128 K × 72 Commercial
Industrial
256 K × 36 Commercial
Industrial
512 K × 18 Commercial
Industrial
64 K × 36 Commercial
Industrial
–
–
–
–
Document Number: 38-06082 Rev. *O
Page 21 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Electrical Characteristics (continued)
Over the Operating Range
-200
-167
Unit
Parameter
Description
Standby current
(both ports TTL Level)
CEL and CER VIH, f = fMAX
Configuration
Typ
1000
–
Max
1250
–
Typ
Max
1160
1260
1050
1160
1030
1140
580
630
530
580
520
570
450
490
400
430
410
440
–
ISB1
512 K × 72 Commercial
Industrial
920
970
820
880
810
860
460
490
410
440
410
430
360
380
340
360
350
370
–
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
1024 K × 36 Commercial
Industrial
910
–
1140
–
2048 K × 18 Commercial
Industrial
890
–
1110
–
256 K × 72 Commercial
Industrial
500
530
460
480
450
470
400
420
380
390
390
410
–
630
680
570
630
560
610
490
540
440
470
460
480
–
512 K × 36 Commercial
Industrial
1024 K × 18 Commercial
Industrial
128 K × 72 Commercial
Industrial
256 K × 36 Commercial
Industrial
512 K × 18 Commercial
Industrial
64 K × 36 Commercial
Industrial
–
–
–
–
Document Number: 38-06082 Rev. *O
Page 22 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Electrical Characteristics (continued)
Over the Operating Range
-200
-167
Unit
Parameter
Description
Standby current
(one port TTL or CMOS level)
CEL | CER VIH, f = fMAX
Configuration
Typ
1300
–
Max
1570
–
Typ
Max
1410
1520
1210
1330
1160
1270
710
760
610
670
580
640
560
610
470
500
480
510
–
ISB2
512 K × 72 Commercial
Industrial
1160
1210
980
1030
930
980
580
610
490
520
470
490
460
480
400
430
410
430
–
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
1024 K × 36 Commercial
Industrial
1090
–
1330
–
2048 K × 18 Commercial
Industrial
1040
–
1270
–
256 K × 72 Commercial
Industrial
650
680
550
570
520
550
520
550
460
480
460
480
–
790
840
670
730
640
690
630
670
530
560
530
560
–
512 K × 36 Commercial
Industrial
1024 K × 18 Commercial
Industrial
128 K × 72 Commercial
Industrial
256 K × 36 Commercial
Industrial
512 K × 18 Commercial
Industrial
64 K × 36 Commercial
Industrial
–
–
–
–
Document Number: 38-06082 Rev. *O
Page 23 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Electrical Characteristics
Over the Operating Range
All Speed Bins
Parameter
ISB3
Description
Configuration
Commercial
Unit
Typ
410
460
410
460
410
460
210
230
210
230
210
230
150
170
150
170
150
170
Max
590
700
590
700
590
700
300
350
300
350
300
350
200
220
200
220
200
220
Standby current
(both ports CMOS level)
CEL and CER VCORE – 0.2 V, f = 0
512 K × 72
1024 K × 36
2048 K × 18
256 K × 72
512 K × 36
1024 K × 18
128 K × 72
256 K × 36
512 K × 18
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
Industrial
Commercial
Industrial
Commercial
Industrial
Commercial
Industrial
Commercial
Industrial
Commercial
Industrial
Commercial
Industrial
Commercial
Industrial
Commercial
Industrial
Capacitance
Signals
Packages
CYD18S72V18
CYD09S72V18
CYD18S36V18
CYD09S36V18
CYD02S36V18
CYD18S18V18
CYD09S18V18
CYD36S72V18
CYD36S36V18
CYD36S18V18
OE
12 pF
10 pF
10 pF
12 pF
18 pF
10 pF
20 pF
16 pF
16 pF
20 pF
30 pF
16 pF
BE, DQ
All other signals
Thermal Resistance
256-ball BGA 256-ball BGA
(18Mbit only) (9Mbit & 2Mbit)
Parameter
Description
Test Conditions
484-ball BGA
Unit
JA
Thermal resistance
(junction to ambient)
Still air, soldered on a 3 × 4.5 inch,
four layer printed circuit board
14.92
17.02
18.31
°C/W
JC
Thermal resistance
(junction to case)
3.6
1.25
1.68
°C/W
Document Number: 38-06082 Rev. *O
Page 24 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
AC Test Load and Waveforms
Figure 9. Output Test Load for LVTTL/CMOS
VTH = 1.5V for LVTTL
VTH = 50% VDDIO for 2.5V CMOS
VTH = 50% VDDIO for 1.8V CMOS
VREF = NC
VREF
Output
50 Ohm
50 Ohm
Test Point
R=250 Ohm
VTH
READY ZQ
Device under
test
C = 10pF
RQ=250 Ohm
Figure 10. Output Test Load for HSTL
VTH = 50% VDDIO
VREF = 0.75V
VREF
50 Ohm
50 Ohm
Output
R=250 Ohm
Test Point
VTH
READY ZQ
C= 10pF for SDR
Device under
test
RQ=250 Ohm
Figure 11. HSTL Input Waveform
Document Number: 38-06082 Rev. *O
Page 25 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Switching Characteristics
Over the Operating Range
Table 12. SDR Mode, Signals Affected by DLL
Description
Parameter
DLL ON (LOWSPD=1)[46]
-200 -167
DLL OFF (LOWSPD=0)[46]
Unit
Min
Max
Min
Max
Min
Max
3.30[45, 48]
–
4.00[45, 48]
–
6.00[45, 48]
ns
[49]
tCD2
C rise to DQ valid for pipelined
mode
–
[49]
tCCQ
C rise to CQ rise
1.00
1.00
3.30 [48]
3.30[45, 48]
1.00
1.00
4.00[48]
4.00[45, 48]
1.00
1.00
6.00[48]
6.00[45, 48]
ns
ns
[44, 49]
tCKHZ2
C rise to DQ output high Z in
pipelined mode
[44, 49]
tCKLZ2
C rise to DQ output low Z in
pipelined mode
1.00
–
1.00
–
1.00
–
ns
Table 13. SDR Mode
Parameter
-200
-167
Description
Unit
Min
Max
Min
Max
fMAX
Maximum operating frequency for pipelined mode
100
200
100
167
MHz
(PIPELINED)
fMAX (FLOW Maximum operating frequency for flow through mode
THROUGH)
–
77
10.00
–
–
66.7
10.00
–
MHz
ns
tCYC
C clock cycle time for pipelined mode
5.00[48]
13.00[48]
6.00[48]
15.00[48]
(PIPELINED)
tCYC (FLOW X C clock cycle time for flow through mode
THROUGH)
ns
tCKD
tSD
C clock duty time
45
55
–
45
55
–
%
Data input setup time to C HSTL
rise
1.50[45, 48]
1.70[45, 48]
ns
1.8 V LVCMOS
2.5 V LVCMOS
3.3 V LVTTL
1.75[45, 48]
–
1.95[45, 48]
ns
[47]
tHD
Data input hold time after C rise
0.5
–
–
0.5
–
–
ns
ns
tSAC
Address and control input HSTL
1.50[45, 47, 48]
1.70[45, 47, 48]
setup time to C rise
1.8 V L VCMOS
2.5 V LVCMOS
3.3 V LVTTL
1.75[45, 47, 48]
–
1.95[45, 47, 48]
–
ns
[47]
tHAC
tOE
Address and control input hold time after C rise
Output enable to data valid
OE to low Z
0.50
–
–
4.40[45, 48]
–
0.60
–
–
5.00[45, 48]
–
ns
ns
ns
[44]
tOLZ
1.00
1.00
Notes
44. Parameters specified with the load capacitance in Figure 9 on page 25 and Figure 10 on page 25.
45. For the x18 devices, add 200 ps to this parameter in Table 13.
46. Test conditions assume a signal transition time of 2 V/ns.
47. Add 300 ps to this timing for 36M devices.
48. Add 15% to this parameter if a VCORE of 1.5 V is used.
49. This parameter assumes input clock cycle to cycle jitter of ± 0 ps.
Document Number: 38-06082 Rev. *O
Page 26 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Table 13. SDR Mode (continued)
-200
-167
Unit
Min Max
Parameter
Description
Min
1.00
–
Max
[50]
tOHZ
tCD1
OE to high Z
4.40[51, 52]
9.00[51, 52]
1.00
–
5.00[51, 52]
11.00[51, 52] ns
ns
C rise to DQ valid for flow through mode
(LowSPD = 0)
tCA1
tCA2
C rise to address readback valid for flow through mode
C rise to address readback valid for pipelined mode
DQ output hold after C rise
–
–
9.00[52]
5.00[52]
–
–
–
11.00[52]
6.00[52]
–
ns
ns
ns
ps
ns
[53]
tDC
1.00
–
1.00
–
tJIT
Clock input cycle to cycle jitter
+/- 200
0.70[51]
+/- 200
0.80[51]
[53]
[53]
tCQHQV
Echo clock (CQ) high to
output valid
HSTL
1.8 V LVCMOS
–
–
2.5 V LVCMOS
3.3 V LVTTL
–
0.80[51]
–
0.90[51]
ns
ns
ns
tCQHQX
Echo clock (CQ) high to
output hold
HSTL
1.8 V LVCMOS
–0.70
–0.85
–
–
–0.80
–0.95
–
–
2.5 V LVCMOS 3.3 V
LVTTL
[50]
tCKHZ1
C rise to DQ output high Z in flow through mode
C rise to DQ output low Z in flow through mode
Address output hold after C rise
C rise to address output high Z for flow through mode
C rise to address output high Z for pipelined mode
C rise to address output low Z
C rise to CNTINT low
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
0.50
0.50
1.00
9.00[51, 52]
–
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
0.50
0.50
1.00
11.00[51, 52] ns
[50]
tCKLZ1
tAC
tCKHZA1
–
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
–
–
9.00[52]
5.00[52]
–
3.30[52]
3.30[52]
7.00[52]
7.00[52]
3.30[52]
11.00[52]
6.00[52]
–
[50]
[50]
tCKHZA2
[50]
tCKLZA
tSCINT
tRCINT
tSINT
4.00[52]
4.00[52]
8.00[52]
8.00[52]
4.00[52]
C rise to CNTINT high
C rise to INT low
tRINT
C rise to INT high
tBSY
C rise to BUSY valid
Notes
50. Parameters specified with the load capacitance in Figure 9 on page 25 and Figure 10 on page 25.
51. For the × 18 devices, add 200 ps to this parameter in Table 13.
52. Add 15% to this parameter if a VCORE of 1.5 V is used.
53. This parameter assumes input clock cycle to cycle jitter of ±0 ps.
Document Number: 38-06082 Rev. *O
Page 27 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Table 14. Master Reset Timing
Parameter
-200
-167
Unit
Max
Description
Min
1
Max
–
Min
1
tPUP
tRS
Power-up time
–
–
ms
cycles
cycles
ns
Master reset pulse width
5
–
5
tRSR
tRSF
tRDY
Master reset recovery time
Master reset to outputs inactive/Hi Z
Master reset release to port ready
C rise to port ready
5
–
5
–
–
15
–
18
[54]
[55]
–
1024
9.5[56]
–
1024
11[56]
cycles
ns
tCORDY
–
–
Table 15. JTAG Timing
Parameter
-200
-167
Description
Unit
Min
–
Max
20
–
Min
–
Max
20
–
fJTAG
tTCYC
tTH
JTAG TAP controller frequency
TCK cycle time
MHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
50
20
20
10
10
10
10
–
50
20
20
10
10
10
10
–
TCK high time
–
–
tTL
TCK low time
–
–
tTMSS
tTMSH
tTDIS
tTDIH
tTDOV
tTDOX
tJXZ
TMS setup to TCK rise
TMS hold to TCK rise
TDI setup to TCK rise
TDI hold to TCK rise
TCK low to TDO valid
TCK low to TDO invalid
TCK low to TDO high Z
TCK low to TDO active
TCK low to TDO active
–
–
–
–
–
–
–
–
10
–
10
–
0
0
–
15
15
15
–
15
15
15
tJZX
–
–
tJZX
–
–
.
Notes
54. READY is a wired OR capable output with a weak pull-down. For a decreased falling delay, connect a 250- resistor to V
.
SS
55. Add this propagation delay after t
for all Master Reset Operations.
RDY
56. Add 15% to this parameter if a VCORE of 1.5 V is used.
Document Number: 38-06082 Rev. *O
Page 28 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Switching Waveforms
Figure 12. JTAG Timing
tTH
tTL
Test Clock
TCK
tTCYC
tTMSS
tTMSH
Test Mode Select
TMS
tTDIS
tTDIH
Test Data-In
TDI
Test Data-Out
TDO
tTDOX
tTDOV
Figure 13. Master Reset [57]
~
V
CORE
t
t
RS
PUP
~
~
MRST
C
t
t
RDY
CORDY
~
~
READY
t
RSF
All Address
& Data
t
RSR
All Other
Inputs
~
Note
57. READY is a wired OR capable output with a weak pull-down. For a decreased falling delay, connect a 250- resistor to VSS.
Document Number: 38-06082 Rev. *O
Page 29 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Switching Waveforms (continued)
Figure 14. READ Cycle for Pipelined Mode
t
CYC
C
CE
OE
t
t
HAC
SAC
R/W
A
A
A
A
A
A
A
A
n
n+1
x
n+2
n
n+3
n+4
n+5
n+6
2 Pipelined stages
DQ
DQ
DQ
DQ
DQ
DQ
DQ
n+4
x-1
n+1
n+2
n+3
DQ
t
DC
t
CD2
Figure 15. WRITE Cycle for Pipelined and Flow through Modes
t
CYC
C
CE
R/W
A
A
A
A
A
A
A
n+6
A
n
n+1
n+2
n+3
n+4
n+5
2 Pipelined stages
DQ
DQ
DQ
DQ
DQ
DQ
DQ
n+6
n
n+1
n+2
n+3
n+4
n+5
DQ
tSD tHD
Document Number: 38-06082 Rev. *O
Page 30 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Switching Waveforms (continued)
Figure 16. READ with Address Counter Advance for Pipelined Mode
t
CYC
C
A
A
n
Internal
Address
A
A
A
A
n+1
n+2
n+3
n
ADS
CNTEN
DQ
DQ
DQ
DQ
DQ
n+1
x-1
x
n
DQ
DQ
n+2
n+3
Figure 17. READ with Address Counter Advance for Flow through Mode
tCYC
C
tSAC tHAC
A
An
ADS
CNTEN
DQ
tSAC tHAC
tCD1
DQx
DQn
DQn + 1
DQn + 2
DQn + 3
DQn + 4
tDC
READ EXTERNAL ADDRESS
READ W ITH COUNTER
COUNTER HOLD
READ W ITH COUNTER
Document Number: 38-06082 Rev. *O
Page 31 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Switching Waveforms (continued)
Figure 18. Port-to-Port WRITE–READ for Pipelined Mode
t
CYC
Left Port
C
L
A
A
n
L
R/WL
DQ
DQ
L
n
Right Port
t
CCS
C
R
t
CYC
A
R
A
n
R/WR
t
t
SAC HAC
DQ
R
DQ
n
t
t
DC
CD2
Figure 19. Chip Enable READ for Pipelined Mode
t
CYC
C
CE0
CE1
R/W
A
t
t
SAC HAC
A
A
A
A
A
A
A
n+6
n
n+1
n+2
n+3
n+4
n+5
DQ
DQ
DQ
n+3
n
t
t
DC
t
CD2
CKLZ2
Document Number: 38-06082 Rev. *O
Page 32 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Switching Waveforms (continued)
Figure 20. OE Controlled WRITE for Pipelined Mode
t
CYC
C
A
A
A
A
A
A
A
A
n+3
x+1
x+2
x+3
n
n+1
n+2
R/W
OE
tOHZ
DQ
x+1
DQ
DQ
DQ
DQ
DQ
DQ
n+3
DQ
x-1
x
n
n+1
n+2
Figure 21. OE Controlled WRITE for Flow through Mode
t
CYC
C
A
A
A
A
A
A
A
A
n+3
x+1
x+2
x+3
n
n+1
n+2
R/W
OE
tOHZ
DQ
x+2
DQ
DQ
DQ
DQ
DQ
DQ
n+3
DQ
x
x+1
n
n+1
n+2
Document Number: 38-06082 Rev. *O
Page 33 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Switching Waveforms (continued)
Figure 22. Byte-Enable READ for Pipelined Mode
tCYC
C
A
A
A
A
A
n
n+1
n+2
n+3
R/W
BE7
BE6
BE5
BE4
BE3
BE2
BE1
BE0
tCKLZ2
tCKHZ2
DQn+1(63:71)
DQ
63:71
54:62
DQn+1(54:62)
DQ
DQ
DQ
DQn+2(45:53)
45:53
36:44
DQn+2(36:44)
DQn+1(27:35)
DQ
DQ
27:35
18:26
DQn+2(18:26)
DQn+3(9:17)
DQ
DQ
9:17
0:8
DQn+3(0:8)
Document Number: 38-06082 Rev. *O
Page 34 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Switching Waveforms (continued)
Figure 23. Port-to-Port WRITE-to-READ for Flow through Mode
CL
R/W L
AL
tSAC
tHAC
NO MATCH
MATCH
tSD
tHD
VALID
DQL
tCCS
CR
tCD1
R/W R
tHAC
tSAC
NO MATCH
AR
MATCH
tCD1
DQR
VALID
VALID
tDC
tDC
Document Number: 38-06082 Rev. *O
Page 35 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Switching Waveforms (continued)
Figure 24. Busy Address Readback for Pipelined and Flow through Modes, CNT/MSK = RET = LOW [58]
t
CYC
~
~
C
Internal
Address
Amatch+2
Amatch+3
Amatch+4
BUSY
~
~
CNTEN
ADS
~
~
External
Address
Amatch
Pipelined
tAC
tCA2
External
Address
~
Amatch
Flow through
tAC
tCA1
Figure 25. Read Cycle for Flow through Mode
tCYC
C
CE0
CE1
tSAC
tHAC
BEn
R/W
A
tSAC
tHAC
An
An + 1
An + 2
An + 3
tCKHZ1
tCD1
tDC
DQ
OE
DQn
DQn + 1
DQn + 2
tDC
tCKLZ1
tOLZ
tOHZ
tOE
Note
58. A
is the matching address that is reported on the address bus of the losing port. The counter operation selected for reporting the address is “Busy Address
match
Readback.”
Document Number: 38-06082 Rev. *O
Page 36 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Switching Waveforms (continued)
Figure 26. READ-to-WRITE for Pipelined Mode (OE = VIL) [59, 60, 61]
tCYC
tCL
C
A
tCH
A
A
x
A
A
n+2
n
n+1
tSAC tHAC
tSAC tHAC
R/W
DQ
t
CKLZ2
DQ
DQ
DQ
x
DQ
x-2
x-1
DQ
n+2
DQ
n+1
n
tDC
tCD2
tCKHZ2
tSD tHD
Figure 27. READ-to-WRITE for Pipelined Mode (OE Controlled) [62, 63]
tCYC
C
A
A
A
A
A
A
A
A
n+3
x
x+1
x+2
n
n+1
n+2
tSAC tHAC
R/W
OE
tOHZ
tSD tHD
DQ
x
DQ
DQ
DQ
DQ
DQ
DQ
n+3
DQ
x-2
x-1
n
n+1
n+2
Notes
59. When OE = V , the last read operation is enabled to complete before the DQ bus is tri-stated and the user is enabled to drive write data.
IL
60. Two dummy writes are issued to accomplish bus turnaround. The third instruction is the first valid write.
61. Chip enable or all byte enables are held inactive during the two dummy writes to avoid data corruption.
62. OE is deasserted and t
enabled to elapse before the first write operation is issued.
OHZ
63. Any write scheduled to complete after OE is deasserted is pre-empted.
Document Number: 38-06082 Rev. *O
Page 37 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Switching Waveforms (continued)
Figure 28. Read-to-Write-to-Read for Flow through Mode (OE = LOW)
tCYC
C
tSAC tHAC
CE0
CE1
BEn
tSAC
tHAC
R/W
A
An
An + 1
An + 2
An + 2
An + 3
An + 4
tSD
tHD
DQIN
DQn + 2
tCD1
tCD1
tCD1
tCD1
DQn
tDC
DQOUT
DQn + 1
DQn + 3
tCKHZ1
tCKLZ1
tDC
READ
NOP
W RITE
READ
Document Number: 38-06082 Rev. *O
Page 38 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Switching Waveforms (continued)
Figure 29. Read-to-Write-to-Read for Flow through Mode (OE Controlled)
tCYC
C
tHAC
tSAC
CE0
CE1
BEn
tHAC
tSAC
R/W
A
An
An + 1
An + 2
tHD
An + 3
An + 4
An + 5
tSD
DQIN
DQn + 2
DQn + 3
tOE
tCD1
tCD1
tDC
tCD1
DQOUT
DQn
DQn + 4
tDC
tCKLZ1
tOHZ
OE
READ
W RITE
READ
Document Number: 38-06082 Rev. *O
Page 39 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Switching Waveforms (continued)
Figure 30. BUSY Timing, WRITE-WRITE Collision for Pipelined and Flow through Modes, Clock Timing Violates tCCS
(Flag Both Ports)
.
Port A
C
A
R/W
BUSY
C
tBSY
tBSY
< tCCS
Port B
A
R/W
tBSY
tBSY
BUSY
Figure 31. BUSY Timing, WRITE-WRITE Collision for Pipelined and Flow through Modes, Clock Timing Meets tCCS
(Flag Losing Port)
.
Losing Port
C
A
R/W
tccs
tBSY
BUSY
tBSY
Winning Port
C
A
Match
R/W
BUSY
Document Number: 38-06082 Rev. *O
Page 40 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Switching Waveforms (continued)
Figure 32. Read with Echo Clock for Pipelined Mode (CQEN = HIGH)
C
tSAC
tHAC
R/W
An
An+1
An+2
An+3
An+4
An+5
An+6
A
CQ0
CQ0
CQ1
tCCQ
CQ1
DQ
tCQHQX
tCQHQV
DQn
DQn+1
DQn+2
DQn+3
DQn+4
DQx-1
DQx
Document Number: 38-06082 Rev. *O
Page 41 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Switching Waveforms (continued)
Figure 33. Mailbox Interrupt Output
t
CYC
C
L
A
MAX
A
L
R/WL
DQ
L
INT
R
t
SINT
t
RINT
C
R
A
MAX
A
R
R/WR
DQ
MAX
DQ
R
Document Number: 38-06082 Rev. *O
Page 42 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Ordering Information
512 K
×
72 (36-Mbit) 1.8 V/1.5 V Synchronous CYD36S72V18 Dual Port SRAM
Package
Speed
(MHz)
Operating
Range
Ordering Code
Package Type
Diagram
200 CYD36S72V18-200BGXC
167 CYD36S72V18-167BGXI
001-07825 484-ball Ball Grid Array 27 mm × 27 mm with 1.0 mm pitch (Pb-free) Commercial
001-07825 484-ball Ball Grid Array 27 mm × 27 mm with 1.0 mm pitch (Pb-free) Industrial
256 K
× 72 (18-Mbit) 1.8 V/1.5 V Synchronous CYD18S72V18 Dual Port SRAM
Package
Diagram
Speed
(MHz)
Operating
Range
Ordering Code
Package Type
200 CYD18S72V18-200BGXI
200 CYD18S72V18-200BGI
167 CYD18S72V18-167BGI
51-85218 484-ball Ball Grid Array 23 mm × 23 mm with 1.0 mm pitch (Pb-free) Industrial
51-85218 484-ball Ball Grid Array 23 mm × 23 mm with 1.0 mm pitch
51-85218 484-ball Ball Grid Array 23 mm × 23 mm with 1.0 mm pitch
Industrial
Industrial
128 K
× 72 (9-Mbit) 1.8 V/1.5 V Synchronous CYD09S72V18 Dual Port SRAM
Package
Diagram
Speed
(MHz)
Operating
Range
Ordering Code
Package Type
167 CYD09S72V18-167BBXC
51-85218 484-ball Ball Grid Array 23 mm × 23 mm with 1.0 mm pitch (Pb-free) Commercial
1024 K
× 36 (36-Mbit) 1.8 V/1.5 V Synchronous CYD36S36V18 Dual Port SRAM
Speed
(MHz)
Package
Diagram
Operating
Range
Ordering Code
Package Type
167 CYD36S36V18-167BGXI
001-07825 484-ball Ball Grid Array 27 mm × 27 mm with 1.0 mm pitch (Pb-free) Industrial
512 K
× 36 (18-Mbit) 1.8 V/1.5 V Synchronous CYD18S36V18 Dual Port SRAM
Package
Diagram
Speed
(MHz)
Operating
Range
Ordering Code
Package Type
200 CYD18S36V18-200BBAXI
167 CYD18S36V18-167BBAI
51-85108 256-ball Ball Grid Array 17 mm × 17 mm with 1.0 mm pitch (Pb-free) Industrial
51-85108 256-ball Ball Grid Array 17 mm × 17 mm with 1.0 mm pitch
Industrial
Document Number: 38-06082 Rev. *O
Page 43 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Ordering Information (continued)
256 K
×
36 (9-Mbit) 1.8 V/1.5 V Synchronous CYD09S36V18 Dual Port SRAM
Package
Speed
(MHz)
Operating
Range
Ordering Code
Package Type
Diagram
200 CYD09S36V18-200BBXI
167 CYD09S36V18-167BBXC
51-85108 256-ball Ball Grid Array 17 mm × 17 mm with 1.0 mm pitch (Pb-free) Industrial
51-85108 256-ball Ball Grid Array 17 mm × 17 mm with 1.0 mm pitch (Pb-free) Commercial
64 K
× 36 (2-Mbit) 1.8 V or 1.5 V Synchronous CYD02S36V18 Dual Port SRAM
Package
Diagram
Speed
(MHz)
Operating
Range
Ordering Code
Package Type
200 CYD02S36V18-200BBC
200 CYD02S36V18-200BBXC
51-85108 256-ball Ball Grid Array 17 mm × 17 mm with 1.0 mm pitch
Commercial
51-85108 256-ball Ball Grid Array 17 mm × 17 mm with 1.0 mm pitch (Pb-free) Commercial
Document Number: 38-06082 Rev. *O
Page 44 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Ordering Information (continued)
2048 K
×
18 (36-Mbit) 1.8 V/1.5 V Synchronous CYD36S18V18 Dual Port SRAM
Package
Speed
(MHz)
Operating
Range
Ordering Code
Package Type
Diagram
167 CYD36S18V18-167BGXI
001-07825 484-ball Ball Grid Array 27 mm × 27 mm with 1.0 mm pitch (Pb-free) Industrial
1024 K
× 18 (18-Mbit) 1.8 V/1.5 V Synchronous CYD18S18V18 Dual Port SRAM
Package
Diagram
Speed
MHz)
Operating
Range
Ordering Code
Package Type
200 CYD18S18V18-200BBAXI
200 CYD18S18V18-200BBAXC
167 CYD18S18V18-167BBAXI
51-85108 256-ball Ball Grid Array 17 mm × 17 mm with 1.0 mm pitch (Pb-free) Industrial
51-85108 256-ball Ball Grid Array 17 mm × 17 mm with 1.0 mm pitch (Pb-free) Commercial
51-85108 256-ball Ball Grid Array 17 mm × 17 mm with 1.0 mm pitch (Pb-free) Industrial
512 K
× 18 (9-Mbit) 1.8 V/1.5 V Synchronous CYD09S18V18 Dual Port SRAM
Package
Diagram
Speed
(MHz)
Operating
Range
Ordering Code
Package Type
167 CYD09S18V18-167BBXI
51-85108 256-ball Ball Grid Array 17 mm × 17 mm with 1.0 mm pitch (Pb-free) Industrial
Ordering Code Definitions
CY DXX SXX V18 - XXX XXX
X
X
Temperature Range: X = C or I
C = Commercial; I = Industrial
Pb-free
Package Type: (XXX = BG or BB or BBA)
BG = 484-ball BGA; BBA or BB = 256-ball BGA
Speed Grade: XXX = 167 MHz or 200 MHz
V18 = 1.8 V
Data Width: SXX = S72 or S36 or S18
Density in Mb: DXX = D36 or D 18 or D09 or D02
CY = Cypress
Document Number: 38-06082 Rev. *O
Page 45 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Package Diagrams
Figure 34. 256-ball FBGA (17 × 17 × 1.7 mm) BB256/BW0BD Package Outline, 51-85108
51-85108 *I
Document Number: 38-06082 Rev. *O
Page 46 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Package Diagrams (continued)
Figure 35. 484-ball PBGA (23 × 23 × 2.03 mm) BY484 Package Outline, 51-85218
51-85218 *A
Document Number: 38-06082 Rev. *O
Page 47 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Package Diagrams (continued)
Figure 36. 484-ball PBGA (27 × 27 × 2.33 mm) BY484S Package Outline, 001-07825
001-07825 *B
Document Number: 38-06082 Rev. *O
Page 48 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Acronyms
Document Conventions
Units of Measure
Acronym
Description
BGA
CMOS
DLL
ball grid array
Symbol
°C
Unit of Measure
complementary metal oxide semiconductor
delay lock loop
degree Celsius
megahertz
microampere
milliampere
millisecond
millivolt
MHz
µA
mA
ms
mV
ns
FBGA
HSTL
I/O
fine pitch ball gird array
high speed transceiver logic
input/output
SDR
SRAM
TCK
TDI
single data rate
static random access memory
test clock
nanosecond
picofarad
volt
pF
V
test data-in
TDO
TMS
VIM
test data-out
test mode select
W
watt
variable impedance matching
Document Number: 38-06082 Rev. *O
Page 49 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Document History Page
Document Title: CYDXXS72V18/CYDXXS36V18/CYDXXS18V18, FullFlex™ Synchronous SDR Dual Port SRAM
Document Number: 38-06082
Submission
Date
Orig. of
Change
REV.
ECN NO.
Description of Change
**
302411
334036
See ECN
See ECN
YDT
YDT
New data sheet
*A
Corrected typo on page 1
Reproduced PDF file to fix formatting errors
*B
395800
See ECN
SPN
Added statement about no echo clocks for flow through mode
Updated electrical characteristics
Added note 16 and 17 (1.5 V timing)
Added note 33 (timing for x18 devices)
Updated input edge rate (note 34)
Updated table 5 on deterministic access control logic
Added description of busy readback in deterministic access control section
Changed dummy write descriptions
Updated ZQ pins connection details
Updated note 24, B0 to BE0
Added power supply requirements to MRST and VC_SEL
Added note 4 (VIM disable)
Updated supply voltage to ground potential to 4.1 V
Updated parameters on table 15
Updated and added parameters to table 16
Updated x72 pinout to SDR only pinout
Updated 484 PBGA pin diagram
Updated the pin definition of MRST
Updated the pin definition of VC_SEL
Updated READY description to include Wired OR note
Updated master reset to include wired OR note for READY
Updated minimum VOH value for the 1.8 V LVCMOS configuration
Updated electrical characteristics to include IOH and IOL values
Updated electrical characteristics to include READY
Added IIX3
Updated maximum input capacitance
Added Notes 33 and 34Removed Notes 15 and 17
Updated Pin Definitions for CQ0, CQ0, CQ1, and CQ1
Removed -100 Speed bin from Selection Guide
Changed voltage name from VDDQ to VDDIO
Changed voltage name from VDD to VCORE
Moved the Mailbox Interrupt Timing Diagram to be the final timing diagram
Updated the Package Type for the CYD36S18V18 parts
Updated the Package Type for the CYD36S18V18 parts
Updated the Package Type for the CYD18S18V18 parts
Updated the Package Type for the CYD18S36V18 parts
Included the Package Diagram for the 256-Ball FBGA (19 x 19 mm) BW256
Included an OE Controlled Write for Flow through Mode Switching Waveform
Included a Read with Echo Clock Switching Waveform
Updated Figure 5 and Figure 6
Updated Electrical Characteristics for READY VOH and READY V
Updated Electrical Characteristics for VOH and VOL for the -167 and -133
speeds
Included a Unit column for Table 5
Removed Switching Characteristic tCA from chart
Included tOHZ in Switching Waveform OE Controlled Write for Pipelined Mode
Included tCKLZ2 in Waveform Read-to-Write-to-Read for Flow through Mode
Document Number: 38-06082 Rev. *O
Page 50 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Document History Page (continued)
Document Title: CYDXXS72V18/CYDXXS36V18/CYDXXS18V18, FullFlex™ Synchronous SDR Dual Port SRAM
Document Number: 38-06082
Submission
Date
Orig. of
Change
REV.
ECN NO.
Description of Change
Updated AC Test Load and Waveforms
*C
402238
SEE ECN
KGH
Included FullFlex36 SDR 484-Ball BGA Pinout (Top View)
Included FullFlex18 SDR 484-Ball BGA Pinout (Top View)
Included Timing Parameter tCORDY
*D
458131
SEE ECN
YDT
Changed ordering information with Pb-free part numbers
Removed VC_SEL
Added IO and core voltage adders
Removed references to bin drop for LVTTL/2.5 V LVCMOS and 1.5 V core
modes
Updated Cin and Cout
Updated ICC, ISB1, ISB2 and ISB3 tables
Updated busy address read back timing diagram
Added HTSL input waveform
Removed HSTL (AC) from DC tables
Added 484-ball 27 mm × 27 mm × 2.33 mm PBGA package
*E
470031
SEE ECN
YDT
Changed VOL of 1.8 V LVCMOS to 0.45 V
Updated tRSF
VREF is DNU when HSTL is not used
Formatted pin description table
Changed VDDIO pins for 36M × 36 and 36M × 18 pinouts
Changed 36M × 72 JTAG IDCODE
*F
500001
627539
SEE ECN
SEE ECN
YDT
QSL
DLL Change, added Clock Input Cycle to Cycle Jitter
Modified DLL description
Changed Input Capacitance Table
Changed tCCS number
Added note 31
*G
change all NC to DNU
corrected switching waveform for (CQEN = High) from both Pipeline and Flow
through mode to only pipeline mode
Modified master reset description
Modified switching characteristics tables, extracted signals effected by the DLL
into one table and combine all other signals into one table
updated package name
Added footnote for tHD, tHAC and tSAC
changed note 26 description
*H
2505003
See ECN
VKN /
AESA
Modified footnote #1
Removed 250 MHz speed bin
Added 2-Mbit part and it’s related information
Changed ball name ZQ1 to DNU for 18M and lesser density devices
Added 256-ball (17 × 17 mm) BGA package for 18M
Made PORTSTD[1:0] left and right pins driven only by LVTTL reference level
For 1.8 V LVCMOS level, Changed VIH(min) from 1.26 V to 0.65 times VDDIO
and changed VIL(max) from 0.36 V to 0.35 times VDDIO
Changed tHD, tHAC specs for 36M from 0.6 ns/0.7 ns to 0.8 ns (See footnote#
32)
Updated Ordering Information table
Document Number: 38-06082 Rev. *O
Page 51 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Document History Page (continued)
Document Title: CYDXXS72V18/CYDXXS36V18/CYDXXS18V18, FullFlex™ Synchronous SDR Dual Port SRAM
Document Number: 38-06082
Submission
Date
Orig. of
Change
REV.
ECN NO.
Description of Change
*I
2898491
07/01/2010
RAME
Modified “Counter Load Operation” section on page 12 and in Table7 on page
13.
Corrected typo in Table 14. by making LowSPD = 0 for tCD1 spec in the
description.
Modified figure 16. on page 30.
Removed inactive parts from Ordering Information.
Updated Packaging Information.
Corrected “Counter Interrupt operation” Section in Page 14 of the data sheet
Updated ordering information with the parts, CYD02S36V18-200BBC and
CYD36S72V18-167BGI.
*J
2995098
3267210
07/28/2010
05/26/2011
RAME
ADMU
Updated Ordering Information and added Ordering Code Definitions.
Added Acronyms and Units of Measure.
Minor edits.
*K
Updated Electrical Characteristics on page 21 (Removed 133 MHz speed bin).
Updated Switching Characteristics on page 26 (Removed 133 MHz speed bin).
Removed information for 4Mb devices.
Updated Ordering Information.
*L
*M
*N
3357888
3349458
3845411
08/30/2011
10/28/2011
01/29/2013
ADMU
ADMU
ADMU
Added Thermal Resistance.
Updated Pin configuration Figure 1 through 5.
Minor edits in Figure 5 (removed overbars in balls C5 and C12).
Updated Package Diagrams.
Updated Ordering Information (Updated part numbers).
Updated Package Diagrams:
spec 001-07825 – Changed revision from *A to *B.
*O
3895845
02/05/2013
ADMU
Updated Ordering Information (Updated part numbers).
Document Number: 38-06082 Rev. *O
Page 52 of 53
CYDXXS72V18
CYDXXS36V18
CYDXXS18V18
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
Products
Automotive
cypress.com/go/automotive
cypress.com/go/clocks
cypress.com/go/interface
cypress.com/go/powerpsoc
cypress.com/go/plc
PSoC Solutions
Clocks & Buffers
Interface
psoc.cypress.com/solutions
PSoC 1 | PSoC 3 | PSoC 5
Lighting & Power Control
Memory
cypress.com/go/memory
cypress.com/go/image
cypress.com/go/psoc
Optical & Image Sensing
PSoC
Touch Sensing
USB Controllers
Wireless/RF
cypress.com/go/touch
cypress.com/go/USB
cypress.com/go/wireless
© Cypress Semiconductor Corporation, 2005-2013. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 38-06082 Rev. *O
Revised February 5, 2013
Page 53 of 53
All products and company names mentioned in this document may be the trademarks of their respective holders.
相关型号:
CYD18S72V18-167BBC
Dual-Port SRAM, 256KX72, 4ns, CMOS, PBGA484, 23 X 23 MM, 2.03 MM HEIGHT, 1 MM PITCH, PLASTIC, BGA-484
CYPRESS
CYD18S72V18-167BBXC
Dual-Port SRAM, 256KX72, 4ns, CMOS, PBGA484, 23 X 23 MM, 2.03 MM HEIGHT, 1 MM PITCH, LEAD FREE, PLASTIC, BGA-484
CYPRESS
CYD18S72V18-167BBXI
Dual-Port SRAM, 256KX72, 4ns, CMOS, PBGA484, 23 X 23 MM, 2.03 MM HEIGHT, 1 MM PITCH, LEAD FREE, PLASTIC, BGA-484
CYPRESS
CYD18S72V18-167BBXI
256KX72 DUAL-PORT SRAM, 4ns, PBGA484, 23 X 23 MM, 2.03 MM HEIGHT, 1 MM PITCH, LEAD FREE, PLASTIC, BGA-484
ROCHESTER
CYD18S72V18-167BGC
FullFlex Synchronous SDR Dual Port SRAM Commercial and Industrial temperature
CYPRESS
CYD18S72V18-167BGC
256KX72 DUAL-PORT SRAM, 4ns, PBGA484, 23 X 23 MM, 2.03 MM HEIGHT, 1 MM PITCH, PLASTIC, BGA-484
ROCHESTER
CYD18S72V18-167BGI
FullFlex Synchronous SDR Dual Port SRAM Commercial and Industrial temperature
CYPRESS
CYD18S72V18-167BGI
256KX72 DUAL-PORT SRAM, 4ns, PBGA484, 23 X 23 MM, 2.03 MM HEIGHT, 1 MM PITCH, PLASTIC, BGA-484
ROCHESTER
CYD18S72V18-167BGXC
FullFlex Synchronous SDR Dual Port SRAM Commercial and Industrial temperature
CYPRESS
CYD18S72V18-167BGXI
Dual-Port SRAM, 256KX72, 11ns, CMOS, PBGA484, 23 X 23 MM, 2.03 MM HEIGHT, 1 MM PITCH, LEAD FREE, PLASTIC, BGA-484
CYPRESS
CYD18S72V18-200BBC
Dual-Port SRAM, 256KX72, 3.3ns, CMOS, PBGA484, 23 X 23 MM, 2.03 MM HEIGHT, 1 MM PITCH, PLASTIC, BGA-484
CYPRESS
©2020 ICPDF网 联系我们和版权申明