AP3433FNTR-G1 [DIODES]
Switching Regulator, Current-mode, 3A, 2000kHz Switching Freq-Max, QFN-16;型号: | AP3433FNTR-G1 |
厂家: | DIODES INCORPORATED |
描述: | Switching Regulator, Current-mode, 3A, 2000kHz Switching Freq-Max, QFN-16 开关 |
文件: | 总13页 (文件大小:411K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Preliminary Datasheet
3A, 2MHz High Performance Synchronous Buck Converter
AP3433
Features
General Description
•
•
•
Input Voltage Range: 2.95V to 5.5V
The AP3433 is a current mode, PWM synchronous
buck (step-down) DC-DC converter, capable of
driving a 3A load with high efficiency, excellent line
and load regulation.
0.827V Reference Voltage with ±3% Precision
Two 45mΩ(typical) MOSFETs for High
Efficiency at 3A Load
•
•
•
•
•
•
•
•
•
•
•
•
•
High Efficiency: up to 94%
Output Current: 3A
Programmable Frequency:300kHz to 2MHz
Current Mode Control
Synchronizes to External Clock
Adjustable Soft-start
Soft Start-up into Pre-biased Output
UV and OV Power Good Output
Built-in Over Current Protection
Built-in Thermal Shutdown Function
Programmable UVLO Function
Built-in Over Voltage Protection
Thermally Enhanced 3mm×3mm 16-pin QFN
The device integrates two N-channel power
MOSFETs with low on-resistance. Current mode
control provides fast transient response and
cycle-by-cycle current limit.
The switching frequency of AP3433 can be
programmable from 300kHz to 2MHz, which allows
small-sized components, such as capacitors and
inductors. A standard series of inductors from several
different manufacturers are available. This feature
greatly simplifies the design of switch-mode power
supplies.
Under voltage lockout is internally set at 2.6V, but
can be increased by programming the threshold with
a resistor network on the enable pin. The output
voltage startup ramp is controlled by the soft-start pin.
An open drain power good signal indicates the output
is within 93% to 107% of its nominal voltage.
Applications
•
•
Low-voltage, High-density Power Systems
Point of Load Regulation for Consumer
Applications such as Set Top Boxes, LCD
Displays, CPE Equipment
The AP3433 is available in QFN-3×3-16 package.
QFN-3×3-16
Figure 1. Package Type of AP3433
Jul. 2012 Rev. 1. 1
BCD Semiconductor Manufacturing Limited
1
Preliminary Datasheet
3A, 2MHz High Performance Synchronous Buck Converter AP3433
Pin Configuration
FN Package
(QFN-3×3-16)
Pin 1 Mark
16
15
14
13
SW
VIN
12
1
11 SW
2
VIN
E P
SW
10
GND
3
4
9
SS
GND
5
6
7
8
Figure 2. Pin Configuration of AP3433 (Top View)
Pin Description
Pin Number
Pin Name
Function
Supply input pin. A capacitor should be connected between the VIN and GND
pin to keep the DC input voltage constant
1,2,16
VIN
Power ground. This pin should be electrically connected to the power pad under
the IC
3,4
GND
Analog ground. This pin should be electrically connected to GND close to the
device
5
6
7
AGND
FB
Feedback pin. Inverting node of the transconductance error amplifier
Compensation pin. This pin is the output of the transconductance error amplifier
and the input to the current comparator. Connect external compensation elements
to this pin to stabilize the control loop
COMP
8
9
RT/CLK
SS
Resistor timing or external clock input pin
Soft-start pin. An external capacitor connected to this pin sets the output voltage
rise time. This pin can also be used for tracking
Internal power switch output pin. This pin is connected to the inductor and
bootstrap capacitor
10,11,12
13
SW
Bootstrap pin. A bootstrap capacitor is connected between the BOOT pin and SW
pin. The voltage across the bootstrap capacitor drives the internal high-side power
MOSFET
BOOT
Power good indicator output. Asserts low if output voltage is low due to thermal
shutdown, over-current, over/under-voltage or EN shut down
14
15
PGD
EN
Enable pin, internal pull-up current source. Pull below 1.2V to disable. Float to
enable. Can be used to set the on/off threshold (adjust UVLO) with two additional
resistors
Jul. 2012 Rev. 1. 1
BCD Semiconductor Manufacturing Limited
2
Preliminary Datasheet
3A, 2MHz High Performance Synchronous Buck Converter
Functional Block Diagram
AP3433
Figure 3. Functional Block Diagram of AP3433
Ordering Information
AP3433
-
G1: Green
Circuit Type
Package
TR: Tape & Reel
FN: QFN-3×3-16
Temperature
Range
Package
Part Number
Marking ID
Packing Type
QFN-3×3-16
-40 to 85ºC
AP3433FNTR-G1
B1D
Tape & Reel
BCD Semiconductor's Pb-free products, as designated with "G1" suffix in the part number, are RoHS compliant
and green.
Jul. 2012 Rev. 1. 1
BCD Semiconductor Manufacturing Limited
3
Preliminary Datasheet
3A, 2MHz High Performance Synchronous Buck Converter
Absolute Maximum Ratings (Note 1)
AP3433
Parameter
Symbol
VIN
Value
-0.3 to 6.5
-0.3 to 6.5
-0.3 to VIN+0.3
-0.3 to 6.5
-0.3 to 6.5
-0.3 to 6.5
-0.3 to 6.5
-0.3 to 6.5
Unit
V
VIN Pin Voltage
EN Pin Voltage
SW Pin Voltage
FB Pin Voltage
COMP Pin Voltage
PGD Pin Voltage
RT/CLK Pin Voltage
SS Pin Voltage
VEN
V
VSW
V
VFB
V
VCOMP
VPGD
VRT/CLK
VSS
V
V
V
V
Thermal Resistance
(Junction to Ambient)
Thermal Resistance
(Junction to Case)
70
5
ºC/W
ºC/W
θJA
θJC (BOTTOM)
Operating Junction Temperature
Storage Temperature
TJ
-40 to 125
-65 to 150
260
ºC
ºC
ºC
V
TSTG
TLEAD
Lead Temperature (Soldering, 10sec)
ESD (Machine Model)
200
ESD (Human Body Model)
2000
V
Note 1: Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to
the device. These are stress ratings only, and functional operation of the device at these or any other conditions
beyond those indicated under “Recommended Operating Conditions” is not implied. Exposure to “Absolute
Maximum Ratings” for extended periods may affect device reliability.
Recommended Operating Conditions
Parameter
Symbol
VIN
Min
2.95
3
Max
Unit
V
Input Voltage
5.5
Maximum Output Current
Operating Ambient Temperature
IOUT(MAX)
TA
A
-40
85
ºC
Jul. 2012 Rev. 1. 1
BCD Semiconductor Manufacturing Limited
4
Preliminary Datasheet
3A, 2MHz High Performance Synchronous Buck Converter AP3433
Electrical Characteristics
VIN=2.95 to 5.5V, TA=25ºC, unless otherwise specified. Specifications with boldface type apply over full
operating temperature range from -40 to 85ºC.
Parameters
Symbol
Conditions
Min
Typ
Max
Unit
SUPPLY VOLTAGE (VIN PIN)
Input Voltage
VIN
IQ
2.95
5.5
575
5
V
VFB=0.9V,VIN=5V,
TA=25°C, RT=400kΩ
VEN=0V,TA=25°C
2.95V≤VIN≤5.5V
Quiescent Current
360
2
µA
µA
Shutdown
Current
Supply
ISHDN
ENABLE AND UVLO (EN PIN)
VEN_H
Rising
Falling
1.16
1.25
1.18
1.37
2.8
V
V
Enable Threshold
VEN_L
Internal Under Voltage
VUVLO
2.6
V
Lockout Threshold
Internal Under Voltage
VHYS
Hysteresis
150
mV
VOLTAGE REFERENCE (FB PIN)
Voltage Reference
VREF
2.95V≤VIN≤5.5V
0.802
0.827
0.852
V
MOSFET
V
BOOT-SW=5V
45
64
81
mΩ
mΩ
High
On-resistance
Side
Switch
Switch
RON_H
VBOOT-SW=2.95V
VIN=5V
110
42
59
81
mΩ
mΩ
Low
On-resistance
Side
RON_L
VIN=2.95V
110
CURRENT LIMIT
Current
Threshold
Limit
ILIMIT
4.2
6.6
A
THERMAL SHUTDOWN
Thermal Shutdown
Hysteresis
TTSD
140
20
°C
°C
Jul. 2012 Rev. 1. 1
BCD Semiconductor Manufacturing Limited
5
Preliminary Datasheet
3A, 2MHz High Performance Synchronous Buck Converter AP3433
Electrical Characteristics (Continued)
VIN=2.95 to 5.5V, TA=25ºC, unless otherwise specified. Specifications with boldface type apply over full
operating temperature range from -40 to 85ºC.
Parameters
Symbol
Conditions
Min
Typ
Max
Unit
TIMING RESISTOR AND EXTERNAL CLOCK (RT/CLK PIN)
Switching Frequency
300
2000
2000
600
kHz
kHz
kHz
ns
Range (RT Mode)
Switching Frequency
300
Range (CLK Mode)
Switching Frequency
fS
400
75
500
RT=400kΩ
Minimum CLK Pulse
Width
RT/CLK Voltage
0.5
1.6
0.6
V
RT=400kΩ
RT/CLK
Threshold
High
Low
2.2
V
RT/CLK
Threshold
0.4
V
BOOT (BOOT PIN)
BOOT Charge Resistor
BOOT-SW UVLO
RBOOT
VIN=5V
16
Ω
VIN=2.95V
2.2
V
SOFT START (SS PIN)
Charge Current
ISS
VSS=0.4
2.2
1.1
µA
SS
to
Reference
VSS
98% Nominal
V
Crossover
POWER GOOD (PGD PIN)
V
FB Falling (Fault)
91
93
VFB Rising (Good)
VFB Rising (Fault)
Feedback Threshold
VFB_TH
%VREF
107
VFB Falling (Good)
105
Jul. 2012 Rev. 1. 1
BCD Semiconductor Manufacturing Limited
6
Preliminary Datasheet
3A, 2MHz High Performance Synchronous Buck Converter
AP3433
Typical Performance Characteristics
430
425
420
415
410
405
400
395
390
385
380
375
370
365
360
470
460
450
440
430
420
410
400
390
380
370
VIN=5V
V
FB=0.9V
-50
-25
0
25
50
75
100
125
150
2.7
3.0
3.3
3.6
3.9
4.2
4.5
4.8
5.1
5.4
5.7
Temperature (oC)
Input Voltage (V)
Figure 4. Supply Current vs. Input Voltage
Figure 5. Supply Current vs. Temperature
100
95
90
85
80
75
70
65
60
55
50
45
40
35
30
2.60
2.55
2.50
2.45
2.40
2.35
2.30
2.25
2.20
2.15
2.10
VOUT=1.8V
VIN=3.3V
Start Switching
Stop Switching
VIN=5V
-50
-25
0
25
50
75
100
125
150
0
300
600
900 1200 1500 1800 2100 2400 2700 3000
Output Current (mA)
Temperature (oC)
Figure 6. Efficiency vs. Output Current
Figure 7.UVLO Threshold vs. Temperature
Jul. 2012 Rev. 1. 1
BCD Semiconductor Manufacturing Limited
7
Preliminary Datasheet
3A, 2MHz High Performance Synchronous Buck Converter AP3433
Typical Performance Characteristics (Continued)
1020
1010
1000
990
980
970
960
950
940
930
920
910
900
0.834
0.832
0.830
0.828
0.826
0.824
0.822
0.820
0.818
0.816
RT=180k
-50
-25
0
25
50
75
100
125
150
-50
-25
0
25
50
75
100
125
150
Temperature (oC)
Temperature (°C)
Figure 8. Switching Frequency vs. Temperature
Figure 9. Reference Voltage vs. Temperature
800
2000
1900
1800
1700
1600
1500
1400
1300
1200
1100
1000
900
700
600
500
400
300
200
100
800
300
400
500
600
700
800
900
1000
80
100
120
140
160
180
200
RT Resistance (kΩ)
RT Resistance (kΩ)
Figure 10. Switching Frequency vs. RT Resistance
Low Frequency Range
Figure 11. Switching Frequency vs. RT Resistance
High Frequency Range
Jul. 2012 Rev. 1. 1
BCD Semiconductor Manufacturing Limited
8
Preliminary Datasheet
3A, 2MHz High Performance Synchronous Buck Converter AP3433
Typical Performance Characteristics (Continued)
VEN
2V/div
VOUT
1V/div
VSS
VIN
2V/div
VOUT
1V/div
VSS
2V/div
IL
2A/div
2V/div
IL
2A/div
Time 4ms/div
Time 20µs/div
Figure 12. Start up from VIN (VIN=5V, VOUT=1.8V, IOUT=3A)
Figure 13. Disable IC (VIN=5V, VOUT=1.8V, IOUT=3A)
VOUT(AC)
200mV/div
VCLOCK
2V/div
VSW
2V/div
IOUT
2A/div
Time 200µs/div
Time 400ns/div
Figure 14. Load Transient Response
(VIN=5V, VOUT=1.8V, IOUT=0 to 3A)
Figure 15. Synchronizing to External Clock
(fCLOCK=2MHz)
Jul. 2012 Rev. 1. 1
BCD Semiconductor Manufacturing Limited
9
Preliminary Datasheet
3A, 2MHz High Performance Synchronous Buck Converter AP3433
Typical Performance Characteristics (Continued)
VOUT
1V/div
VOUT
1V/div
VSS
VSS
2V/div
2V/div
VCOMP
0.5V/div
VCOMP
0.5V/div
IL
2A/div
IL
2A/div
Time 4ms/div
Time 4ms/div
Figure 16. Short Circuit Protection
(VIN=5V, VOUT=1.8V, IOUT=3A)
Figure 17. Short Circuit Recovery
(VIN=5V, VOUT=1.8V, IOUT=3A)
Jul. 2012 Rev. 1. 1
BCD Semiconductor Manufacturing Limited
10
Preliminary Datasheet
3A, 2MHz High Performance Synchronous Buck Converter AP3433
Typical Application
Figure 18. Typical Application of AP3433
Jul. 2012 Rev. 1. 1
BCD Semiconductor Manufacturing Limited
11
Preliminary Datasheet
3A, 2MHz High Performance Synchronous Buck Converter
AP3433
Mechanical Dimensions
QFN-3×3-16
Unit:mm(inch)
Jul. 2012 Rev. 1. 1
BCD Semiconductor Manufacturing Limited
12
BCD Semiconductor Manufacturing Limited
http://www.bcdsemi.com
- Headquarters
- Wafer Fab
BCD Semiconductor Manufacturing Limited
Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd.
No. 1600, Zi Xing Road, Shanghai ZiZhu Science-based Industrial Park, 200241, China
800 Yi Shan Road, Shanghai 200233, China
Tel: +86-21-24162266, Fax: +86-21-24162277
Tel: +86-21-6485 1491, Fax: +86-21-5450 0008
REGIONAL SALES OFFICE
Shenzhen Office
Taiwan Office
USA Office
Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd., Shenzhen Office
BCD Semiconductor (Taiwan) Company Limited
BCD Semiconductor Corp.
Unit A Room 1203, Skyworth Bldg., Gaoxin Ave.1.S., Nanshan District, Shenzhen,
4F, 298-1, Rui Guang Road, Nei-Hu District, Taipei,
30920 Huntwood Ave. Hayward,
China
Taiwan
Tel: +886-2-2656 2808
CA 94544, USA
Tel: +86-755-8826 7951
Tel : +1-510-324-2988
Fax: +86-755-8826 7865
Fax: +886-2-2656 2806
Fax: +1-510-324-2788
相关型号:
AP3435MPTR-G1
Switching Regulator, Current-mode, 4.5A, 1000kHz Switching Freq-Max, PDSO8, SOP-8
DIODES
©2020 ICPDF网 联系我们和版权申明