PMODACL2 [ETC]
PmodACL2⢠Diigiitall Accellerometer Reference Manuall; PmodACL2â ?? ¢ Diigiitall Accellerometer参考手册册
| 型号： | PMODACL2 |
| 厂家： | 
ETC |
| 描述： | PmodACL2⢠Diigiitall Accellerometer Reference Manuall |
| 文件： | 总1页 (文件大小：150K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
PmodACL2™ Digital Accelerometer
Reference Manual
Revision: November 9, 2012
1300 Henley Court | Pullman, WA 99163
(509) 334 6306 Voice and Fax
Note: This document applies to REV A of the board
Overview
The PmodACL2 is a 3-axis digital
accelerometer module powered by the Analog
Devices ADXL362.
Features include:
•
•
•
•
•
user-selectable resolution
single or double-tap detection
activity and inactivity monitoring
free fall detection
SPI Communication
Functional Description
Connector J1 – SPI Communications
Pin Signal Description
The PmodACL2 uses a standard 12-pin
connector and can communicate via SPI.
While the ADXL362 is in Measurement Mode,
it continuously measures and stores
acceleration data in the X-data, Y-data, and Z-
data registers.
1
~SS
Slave select
2
MOSI
MISO
SCLK
GND
VCC
INT2
INT1
NC
SPI master out slave in data
SPI master in slave out data
Serial clock
3
4
5
Power supply ground
Power supply (3.3V)
Interrupt two
6
7
Do not exceed 3.3V on the VCC power supply.
Exceeding this limit could permanently damage
the ADXL362.
8
Interrupt one
Not connected
9
10
11
12
NC
GND
VCC
Not connected
Power supply ground
Power supply (3.3V)
Interface
All communications with the device must
specify a register address and a flag that
indicate whether the communication is a read
or a write. Actual data transfer always follows
the register address and communication flag.
Table 1. Interface Connector Signal
Description
The SPI standard uses four signal lines. These
are slave select (~SS), master out slave in
(MOSI), master in slave out (MISO), and serial
clock (SCLK). These four signal lines map to
the following signals on the ADXL345: ~SS
corresponds to the chip select signal (~CS),
MOSI corresponds to serial data input (SDI),
MISO corresponds to serial data output (SDO),
and SCK corresponds to the serial clock
Perform device configuration by writing to the
control registers within the accelerometer.
Access accelerometer data by reading the
device registers.
You may find a full list of registers, their
functionality, and communication specifications
in the ADXL362 datasheet available at:
www.analog.com.
(SCLK). (See Table 1 for signal descriptions.)
Doc: 502-255
page 1 of 1
Copyright Digilent, Inc. All rights reserved. Other product and company names mentioned may be trademarks of their respective owners.
相关型号：
PMODDA3
Diigiillentt PmodDA3⢠Diigiittall To Anallog Modulle Convertter Board Refference Manuall
ETC
PMODGYRO2_RM
The PmodGYRO2 features the Analog Devices ADXRS453 High Performance, Digital Output Gyroscope that is ideal for systems in need of a gyroscope for high vibration environments.
ETC
PMODJSTK
The PmodJSTK was designed to be a versatile user interface that can be used in a wide variety of projects.
ETC
©2020 ICPDF网 联系我们和版权申明