SSD1800AV [ETC]
LCD Segment / Common Driver with Controller; LCD段/与控制器的通用驱动程序型号: | SSD1800AV |
厂家: | ETC |
描述: | LCD Segment / Common Driver with Controller |
文件: | 总42页 (文件大小:596K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SOLOMON SYSTECH
SEMICONDUCTOR TECHNICAL DATA
SSD1800
Advance Information
80x16 + 1 Icon line
LCD Segment / Common Driver with Controller
for Character Display System
This document contains information on a new product. Specifications and information herein are
subject to change without notice.
http://www.solomon-systech.com
SSD1800 Series
Rev 1.0
P 1/42
Mar 2004
Copyright 2004 Solomon Systech Limited
TABLE OF CONTENTS
1
GENERAL DESCRIPTION .................................................................................................................5
FEATURES .........................................................................................................................................5
ORDERING INFORMATION...............................................................................................................5
BLOCK DIAGRAM .............................................................................................................................6
PIN ARRANGEMENT OF SSD1800Z GOLD BUMP DIE..................................................................7
PIN ARRANGEMENT OF SSD1800AV BARE DIE.........................................................................10
PIN DESCRIPTIONS ........................................................................................................................12
FUNCTIONAL BLOCK DESCRIPTIONS.........................................................................................15
VOLTAGE GENERATOR CIRCUIT .................................................................................................24
FRAME FREQUENCY......................................................................................................................25
COMMAND TABLE ..........................................................................................................................26
COMMAND DESCRIPTIONS ...........................................................................................................28
MAXIMUM RATINGS........................................................................................................................33
DC CHARACTERISTICS..................................................................................................................34
AC CHARACTERISTICS..................................................................................................................35
APPLICATION EXAMPLES .............................................................................................................38
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Solomon Systech
Mar 2004
P 2/42
Rev 1.0
SSD1800 Series
TABLE OF TABLES
Table 1 - Ordering Information ..................................................................................................................5
Table 2 - SSD1800Z Gold Bump Die Pad Coordinates............................................................................8
Table 3 - SSD1800AV Bare Die Pad Coordinates...................................................................................11
Table 4 - Relationship between ICONRAM Address and Display Pattern...........................................18
Table 5 - CGROM Character Code...........................................................................................................19
Table 6 - Relationship between Character Code (DDRAM) and Character Pattern (CGRAM)...........20
Table 7- Contrast Control Register .........................................................................................................22
Table 8 - Command Table.........................................................................................................................26
Table 9 - DD/ CGRAM Address Mapping ................................................................................................31
Table 10 - ICONRAM Address Mapping..................................................................................................32
Table 11 - Maximum Ratings (Voltage Reference to VSS)....................................................................33
Table 12 - DC Characteristics (Unless otherwise specified, Voltage Referenced to VSS, VDD = 2.4
to 3.6V, TA = -30 to 85°C.).......................................................................................................34
Table 13 - AC Characteristics (Unless otherwise specified, Voltage Referenced to VSS, VDD = 2.4
to 3.6V, TA = -30 to 85°C.).......................................................................................................35
Table 14 - 6800-Series MPU Parallel Interface Timing Characteristics (VDD - VSS = 2.4 to 3.6V, TA =
-30 to 85°C)...............................................................................................................................35
Table 15 - 8080-Series MPU Parallel Interface Timing Characteristics (VDD - VSS = 2.4 to 3.6V, TA =
-30 to 85°C)...............................................................................................................................36
Table 16 - Serial Interface Timing Characteristics (VDD - VSS = 2.4 to 3.6V, TA = -30 to 85°C) .......37
SSD1800 Series Rev 1.0
P 3/42
Mar 2004
Solomon Systech
TABLE OF FIGURES
Figure 1 - Block Diagram of SSD1800.......................................................................................................6
Figure 2 - SSD1800Z Pin Arrangement .....................................................................................................7
Figure 3 - SSD1800AV Pin Arrangement ................................................................................................10
Figure 4 - Timing Diagram of 8-bit Parallel Bus Mode Data Transfer (6800 MPU Mode)...................16
Figure 5 - Timing Diagram of 8-bit Parallel Bus Mode Data Transfer (8080 MPU Mode)...................16
Figure 6 - Timing Diagram of 4-bit Parallel Bus Mode Data Transfer (6800 MPU Mode)...................17
Figure 7 - Timing Diagram of 4-bit Parallel Bus Mode Data Transfer (8080 MPU Mode)...................17
Figure 8 - Timing Diagram of Serial Data Transfer................................................................................17
Figure 9 - DDRAM Address ......................................................................................................................18
Figure 10 - Configurations for DC-DC Converter...................................................................................21
Figure 11 - Configurations for Voltage Regulator .................................................................................21
Figure 12 - When Built-in Power Supply is used ...................................................................................24
Figure 13 - When External Power Supply is used .................................................................................24
Figure 14 - Function set command (X1X0 = 00).....................................................................................28
Figure 15 - COM0 ~ COM15 is a Double Height Line in function set command (X1X0 = 01).............28
Figure 16 - Display Attributes ..................................................................................................................30
Figure 17 - 6800-series MCU Parallel Interface Waveform....................................................................35
Figure 18 - 8080-series MCU Parallel Interface Waveform....................................................................36
Figure 19 - Serial Interface Characteristics............................................................................................37
Figure 20- Application Circuit: External Regulator with internal divider mode (8-bit 6800 mode)...38
Figure 21 - Application Circuit: ALL internal power mode with 2x regulated DC-DC converter
(serial mode).......................................................................................................................................39
Figure 22- Application Circuit: ALL internal power mode with 3x regulated DC-DC converter (8-bit
8080 mode) .........................................................................................................................................40
Figure 23- Recommended INITIALIZING of SSD1800............................................................................41
Solomon Systech
Mar 2004
P 4/42
Rev 1.0
SSD1800 Series
1
GENERAL DESCRIPTION
SSD1800 is a single-chip CMOS LCD driver with controller for liquid crystal dot-matrix character display
system. It consists of 97 high voltage driving output pins for driving 80 Segments, 16 Commons and 1 icon
driving-Common. It can display 2 lines of 16 characters with 5x8 dots format. The double height character mode
and line vertical scroll functions are supported.
SSD1800 displays character directly from its internal 10,240 bits (256 characters x 5 x 8 dots) Character
Generator ROM (CGROM). All the character codes are stored in the 512 bits (16 characters x 4 lines) Data
Display RAM (DDRAM). User defined character can be loaded via 320 bits (8 characters x 5 x 8 dots) Character
Generator RAM (CGRAM). In addition, there is a 80 bits Icon RAM for Icon display. Data/ Commands are sent
from general MCU through software selectable 6800-/8080-series compatible 4/ 8-bit Parallel Interface or Serial
Peripheral Interface.
SSD1800 embeds a DC-DC Converter, Voltage Regulator, Voltage divider and RC oscillator that reduce the
number of external components. With the special design on minimizing power consumption and die size,
SSD1800 is suitable for portable battery-driven applications requiring a long operation period and a compact
size.
2
FEATURES
Single Supply Operation, 2.4V - 3.6V
Maximum 5.8V LCD Driving Output Voltage
Low Current Sleep Mode
On-Chip 2x/3x DC-DC Converter/ External Power Supply
On-Chip RC Oscillator/ External Clock
On-Chip Voltage Regulator
On-Chip Voltage Divider with programmable bias ratio (1/4, 1/5)
32 Level Internal Contrast Control
2 lines x 16 characters with 5x8 dots format display and 80 icons
Double Height Character Mode, Blink Mode, Cursor Display and Line Vertical Scroll Functions
Row remapping and column remapping (4-type LCD application available)
8/4-bit 6800-series Parallel Interface, 8/4-bit 8080-series Parallel Interface and Serial Peripheral Interface
256 Build in characters and 8 user defined characters
On-Chip Memories
Character Generator ROM (CGROM): 10240 bits (256 characters x 5 x 8 dots)
Character Generator RAM (CGRAM): 320 bits (8 characters x 5 x 8 dots)
Display Data RAM (DDRAM): 512 bits (16 characters x 4 lines)
Segment Icon RAM (ICONRAM): 80 bits (80 icons)
Available in Bare Die/Gold bumped Die
3
ORDERING INFORMATION
Table 1 - Ordering Information
Display Size
Ordering Part Number
Package Form
Gold-bump Die
Bare Die
Reference
Remark
SSD1800Z
16x2 Characters
16x2 Characters
Figure 2 on page 7
Figure 3 on page 10
-
-
SSD1800AV
SSD1800 Series Rev 1.0
P 5/42
Mar 2004
Solomon Systech
4
BLOCK DIAGRAM
COM0~
COM15
SEG0~SEG79
COMI0, COMI
Level
HV Buffer Cell (Level Shifter)
Display Data Latch
Selector
VL2
VL3
VL4
VL5
DIRS
VL6
Display
Generator
VF
Cursor and
Control
Regulated DC/DC
Converter,
Voltage Divider,
Contrast Control
Oscillator
CLK
C1P
C1N
C2P
C2N
Internal
Character Generator ROM
Character Generator RAM
Display Data RAM
Icon RAM
AV
DVSS
SS &
AVDD & DVDD
Command Decoder
RES
Reset
circuit
Command Interface
Parallel/ Serial Interface
DL
P/S
D/C
E
R/W C68/80
RES
D7
D D5 D4 D3 D D1
D
0
CS
6
2
(RD) (WR)
(SDA) (SCK)
Figure 1 – Block Diagram of SSD1800
Solomon Systech
Mar 2004
P 6/42
Rev 1.0
SSD1800 Series
5
PIN ARRANGEMENT OF SSD1800Z GOLD BUMP DIE
Alignment Keys
Center (-2101.9, 169.6)
26.3 µm 26.3 µm 26.3 µm
26.3 µm 26.3 µm 26.3 µm
61.3µm
Center (2940.9, 480.0)
Center (-2940.9, 480.0)
8.75µm
8.75µm
37.6µm
37.6µm
X
X
(-2835, -598.5)
(2835, -598.5)
Figure 2 - SSD1800Z Pin Arrangement
Die Size:
6170um x 1480um (include scribe line)
6070um x 1380um (exclude scribe line)
670 +/-25um
Die Thickness:
Bump Size
Minimum Pitch
76.3um
PAD: 1-63
52.15 x 60.2 um
164-178 74.9 x 42 um
42 x 74.9 um
PAD: 65-79,
63.7um
PAD: 81-162
PAD: 64,80,163,179
63.7um
52.15 X 52.15 um
Bump Height: Nominal
18um
Note:
1. PADS: 35-36, 45, 64-65, 75-81, 162-164, 166-169, 178-179 NC pads.
2. The die faces up in the diagram.
3. Coordinates are reference to the center of the chip.
4. Unit of coordinates and size of all alignment keys are in um.
5. All alignment keys do not contain gold bump.
SSD1800 Series Rev 1.0
P 7/42
Mar 2004
Solomon Systech
Table 2 - SSD1800Z Gold Bump Die Pad Coordinates
PAD#
NAME
D/ C
DVSS
X
Y
PAD#
41
42
43
44
NAME
C1N
C1N
C1P
C1P
NC
X
Y
1
2
3
4
5
-2401.53
-2325.23
-2248.93
-2172.63
-2096.33
-600.78
-600.78
-600.78
-600.78
-600.78
684.78
761.08
837.38
913.68
989.98
-600.78
-600.78
-600.78
-600.78
-600.78
R/W ( WR )
DVDD
E(RD )
45
6
-2020.03
-600.78
46
DVSS
1080.63
-600.78
CS
D7
7
-1943.73
-1867.43
-1791.13
-1714.83
-1638.53
-1562.23
-1485.93
-1409.63
-1333.33
-600.78
-600.78
-600.78
-600.78
-600.78
-600.78
-600.78
-600.78
-600.6
47
48
49
50
51
52
53
54
55
AVSS
DVSS
REF
1156.93
1233.23
1309.53
1385.83
1462.13
1538.43
1614.73
1691.03
1767.33
-600.78
-600.78
-600.78
-600.78
-600.78
-600.78
-600.78
-600.78
-600.78
8
D6
9
D5
10
11
12
13
14
15
D4
DIRS
DVDD
AVDD
DVDD
CLK
D3
D2
D1
D0
DVDD
VSS
16
AVDD
-1257.03
-600.6
56
1843.63
-600.78
P / S
DVDD
DL
17
18
19
DVDD
DVSS
AVSS
-1180.73
-1104.43
-1028.13
-600.6
-600.78
-600.6
57
58
59
1919.93
1996.23
2072.53
-600.78
-600.78
-600.78
DVSS
20
21
22
DVSS
VL2
VL2
-951.83
-861.18
-784.88
-600.6
-600.6
-600.6
60
61
62
2148.83
2225.13
2301.43
-600.78
-600.78
-600.78
-600.78
-600.78
-520.1
-456.4
-392.7
-329
C68/( 80 )
DVDD
RES
TEST
NC
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
VL3
VL3
VL4
VL4
VL5
VL5
VL6
VL6
VL6
VL6
VF
-708.58
-632.28
-555.98
-479.68
-403.38
-327.08
-246.05
-169.75
-93.45
-600.6
-600.78
-600.78
-600.78
-600.78
-600.78
-600.78
-600.78
-600.78
-600.78
-600.78
-600.78
-600.78
-600.78
-600.78
-600.78
-600.78
-600.78
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
2377.73
2939.3
2939.3
2939.3
2939.3
2939.3
2939.3
2939.3
2939.3
2939.3
2939.3
2939.3
2939.3
2939.3
2939.3
2939.3
2939.3
2939.3
NC
COMI0
COM 0
COM 1
COM 2
COM 3
COM 4
COM 5
COM 6
COM 7
NC
-265.3
-201.6
-137.9
-74.2
-17.15
64.75
-10.5
VF
141.05
222.25
298.55
379.58
455.88
532.18
608.48
53.2
NC
116.90
180.6
244.3
308.0
371.7
593.43
NC
NC
C2N
C2N
C2P
C2P
NC
NC
NC
NC
Solomon Systech
Mar 2004
P 8/42
Rev 1.0
SSD1800 Series
PAD#
81
NAME
NC
X
Y
PAD#
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
NAME
SEG49
SEG50
SEG51
SEG52
SEG53
SEG54
SEG55
SEG56
SEG57
SEG58
SEG59
SEG60
SEG61
SEG62
SEG63
SEG64
SEG65
SEG66
SEG67
SEG68
SEG69
SEG70
SEG71
SEG72
SEG73
SEG74
SEG75
SEG76
SEG77
SEG78
SEG79
NC
X
Y
2579.85
2516.15
2452.45
2388.75
2325.05
2261.35
2197.65
2133.95
2070.25
2006.55
1942.85
1879.15
1815.45
1751.75
1688.05
1624.35
1560.65
1496.95
1433.25
1369.55
1305.85
1242.15
1178.45
1114.75
1051.05
987.35
923.65
859.95
796.25
732.55
668.85
605.15
541.45
477.75
414.05
350.35
286.65
222.95
159.25
95.55
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
-605.15
-668.85
-732.55
-796.25
-859.95
-923.65
-987.35
-1051.05
-1114.75
-1178.45
-1242.15
-1305.85
-1369.55
-1433.25
-1496.95
-1560.65
-1624.35
-1688.05
-1751.75
-1815.45
-1879.15
-1942.85
-2006.55
-2070.25
-2133.95
-2197.65
-2261.35
-2325.05
-2388.75
-2452.45
-2516.15
-2579.85
-2939.3
-2939.3
-2939.3
-2939.3
-2939.3
-2939.3
-2939.3
-2939.3
-2939.3
-2939.3
-2939.3
-2939.3
-2939.3
-2939.3
-2939.3
-2939.3
-2939.3
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
593.43
371.7
82
SEG0
83
SEG1
84
SEG2
85
SEG3
86
SEG4
87
SEG5
88
SEG6
89
SEG7
90
SEG8
91
SEG9
92
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18
SEG19
SEG20
SEG21
SEG22
SEG23
SEG24
SEG25
SEG26
SEG27
SEG28
SEG29
SEG30
SEG31
SEG32
SEG33
SEG34
SEG35
SEG36
SEG37
SEG38
SEG39
SEG40
SEG41
SEG42
SEG43
SEG44
SEG45
SEG46
SEG47
SEG48
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
NC
NC
COMI1
NC
308
244.3
NC
180.6
NC
116.9
NC
53.2
COM15
COM14
COM13
COM12
COM11
COM10
COM9
COM8
NC
-10.5
31.85
-74.2
-31.85
-137.9
-201.6
-265.3
-329
-95.55
-159.25
-222.95
-286.65
-350.35
-414.05
-477.75
-541.45
-392.7
-456.4
-520.1
-600.78
NC
SSD1800 Series Rev 1.0
P 9/42
Mar 2004
Solomon Systech
6
PIN ARRANGEMENT OF SSD1800AV BARE DIE
Figure 3 - SSD1800AV Pin Arrangement
Die Size:
6260um x 1810um (include scribe line)
Die Thickness:
Pad Metal Size:
Pad Opening Size:
670 +/-25um
88 x 88um
80 x 80um
Pad number
Pad metal size
PADS: 1-9, 48-56, 72-80, 119-127
PADS: 57, 58, 70, 71, 128, 129, 141, 142
PADS: 10-47, 81-118
103um x111um
111um x103um
90um x111um
111um x90um
PADS: 59-69, 130-140
Note:
1. PADS: 1,2, 29, 34, 56-59, 141, 142 are NC pads.
2. The die faces up in the diagram.
3. Coordinates are reference to the center of the chip.
Solomon Systech
Mar 2004
P 10/42 Rev 1.0
SSD1800 Series
Table 3 - SSD1800AV Bare Die Pad Coordinates
PAD #
NAME
NC
X
Y
PAD # NAME
X
Y
PAD # NAME
X
Y
1
2
-2748.20 -772.71 51 COM3
-2638.13 -772.71 52 COM4
2198.53 -772.71 101 SEG41
2308.60 -772.71 102 SEG42
2418.68 -772.71 103 SEG43
2528.75 -772.71 104 SEG44
2638.83 -772.71 105 SEG45
2748.90 -772.71 106 SEG46
2998.10 -687.75 107 SEG47
2998.10 -577.68 108 SEG48
2998.10 -467.60 109 SEG49
2998.10 -372.75 110 SEG50
-145.08 772.98
-239.93 772.98
-334.78 772.98
-429.63 772.98
-524.48 772.98
-619.33 772.98
-714.18 772.98
-809.03 772.98
-903.88 772.98
-998.73 772.98
NC
3
COM15 -2528.05 -772.71 53 COM5
COM14 -2417.98 -772.71 54 COM6
COM13 -2307.90 -772.71 55 COM7
COM12 -2197.83 -772.71 56 NC
COM11 -2087.75 -772.71 57 NC
COM10 -1977.68 -772.71 58 NC
4
5
6
7
8
9
COM9
COM8
-1867.60 -772.71 59 NC
-1757.53 -772.71 60 SEG0
10
11
12
13
14
D/ C
-1662.68 -772.71 61 SEG1
2998.10 -277.90 111 SEG51 -1093.58 772.98
2998.10 -183.05 112 SEG52 -1188.43 772.98
R/W ( WR ) -1567.83 -772.71 62 SEG2
E(RD )
-1472.98 -772.71 63 SEG3
2998.10
2998.10
-88.20 113 SEG53 -1283.28 772.98
6.65 114 SEG54 -1378.13 772.98
CS
D7
-1378.13 -772.71 64 SEG4
-1283.28 -772.71 65 SEG5
-1187.73 -772.71 66 SEG6
-1092.18 -772.71 67 SEG7
-996.63 -772.71 68 SEG8
-901.08 -772.71 69 SEG9
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
2998.10 101.50 115 SEG55 -1472.98 772.98
2998.10 196.35 116 SEG56 -1567.83 772.98
2998.10 291.20 117 SEG57 -1662.68 772.98
2998.10 386.05 118 SEG58 -1757.53 772.98
2998.10 480.90 119 SEG59 -1867.60 772.98
D6
D5
D4
D3
D2
-805.53 -772.71 70 SEG10 2998.10 590.98 120 SEG60 -1977.68 772.98
-709.98 -772.71 71 SEG11 2998.10 701.05 121 SEG61 -2087.75 772.98
-614.43 -772.71 72 SEG12 2742.43 772.98 122 SEG62 -2197.83 772.98
-519.58 -772.71 73 SEG13 2632.35 772.98 123 SEG63 -2307.90 772.98
-424.73 -772.71 74 SEG14 2522.28 772.98 124 SEG64 -2417.98 772.98
-329.88 -772.71 75 SEG15 2412.20 772.98 125 SEG65 -2528.05 772.98
-235.03 -772.71 76 SEG16 2302.13 772.98 126 SEG66 -2638.13 772.98
-140.18 -772.71 77 SEG17 2192.05 772.98 127 SEG67 -2748.20 772.98
-45.33 -772.71 78 SEG18 2081.98 772.98 128 SEG68 -2998.10 -687.75
49.53 -772.71 79 SEG19 1971.90 772.98 129 SEG69 -2998.10 -577.68
144.38 -772.71 80 SEG20 1861.83 772.98 130 SEG70 -2998.10 -467.60
239.23 -772.71 81 SEG21 1751.75 772.98 131 SEG71 -2998.10 -372.75
334.08 -772.71 82 SEG22 1657.08 772.98 132 SEG72 -2998.10 -277.90
428.93 -772.71 83 SEG23 1562.23 772.98 133 SEG73 -2998.10 -183.05
D1
D0
VL2
VL3
VL4
VL5
VL6
VF
NC
C2N
C2P
C1N
C1P
NC
523.78 -772.71 84 SEG24 1467.38 772.98 134 SEG74 -2998.10
618.63 -772.71 85 SEG25 1372.53 772.98 135 SEG75 -2998.10
-88.20
6.65
AVSS
DVSS
REF
DIRS
AVDD
DVDD
CLK
P/ S
DL
C68/( 80 )
713.48 -772.71 86 SEG26 1277.68 772.98 136 SEG76 -2998.10 101.50
808.33 -772.71 87 SEG27 1182.83 772.98 137 SEG77 -2998.10 196.35
903.18 -772.71 88 SEG28 1087.98 772.98 138 SEG78 -2998.10 291.20
998.03 -772.71 89 SEG29
1092.88 -772.71 90 SEG30
1187.73 -772.71 91 SEG31
993.13 772.98 139 SEG79 -2998.10 386.05
898.28 772.98 140 ICONS2 -2998.10 480.90
803.43 772.98 141 NC
-2998.10 590.98
-2998.10 701.05
42
43
44
1282.58 -772.71 92 SEG32
1377.43 -772.71 93 SEG33
708.58 772.98 142 NC
613.73 772.98
1472.28 -772.71 94 SEG34
518.88 772.98
45
RES
TEST
ICONS1
COM0
COM1
COM2
1567.13 -772.71 95 SEG35
1661.98 -772.71 96 SEG36
1758.23 -772.71 97 SEG37
1868.30 -772.71 98 SEG38
1978.38 -772.71 99 SEG39
2088.45 -772.71 100 SEG40
424.03 772.98
329.18 772.98
234.33 772.98
139.48 772.98
44.63 772.98
-50.23 772.98
46
47
48
49
50
SSD1800 Series Rev 1.0
P 11/42 Mar 2004
Solomon Systech
7
PIN DESCRIPTIONS
7.1 D/C
This pin is Data/ Command control pin. When the pin is pulled high, the data at D7-D0 is treated as display data.
When the pin is pulled low, the data at D7-D0 will be transferred to the command register.
7.2 R/( WR )
This pin is microprocessor interface input. When interfacing to a 6800-series microprocessor, this pin will be used
as R/W signal input. Read mode will be carried out when this pin is pulled high and write mode when low.
When interfacing to a 8080-microprocessor, this pin will be the WR input. Data write operation is initiated when
this pin is pulled low and the chip is selected.
This pin must be fixed to high or low in serial mode.
7.3 DVDD & AVDD
Digital and Analog Power supply pin.
7.4 DVSS & AVSS
Ground.
7.5 E(RD )
This pin is microprocessor interface input. When interfacing to a 6800-series microprocessor, this pin will be used
as the enable signal, E. Read/ Write operation is initiated when this pin is pulled high and the chip is selected.
When interfacing to a 8080-microprocessor, this pin receives the RD signal. Data read operation is initiated when
this pin is pulled low and the chip is selected.
This pin must be fixed to high or low in serial mode.
7.6 CS
This pin is the chip select input.
7.7 D7-D0
These pins are the 8-bit bi-directional data bus to be connected to the microprocessor in parallel interface mode.
In 8-bit bus mode, D7 is the MSB while D0 is the LSB. In 4-bit bus mode, it is needed to transfer 4-bit data (through
D7-D4) by two times. The high order bits (for 8-bit mode D7-D4) are written before the low order bits (for 8-bit mode
D3-D0) in write transaction and low order bits (8-bit mode D3-D0) are read before the high order bits (8-bit mode D7-
D4) in read transaction. The D3-D0 pins must be fixed to high or low in 4-bit bus mode. After resets, SSD1800
considers first 4-bit data from MPU as the high order bits.
When serial mode is selected, D7 is the serial data input (SDA) and D6 is the serial clock input (SCK). D5-D0 must
be fixed to high or low in serial mode
Solomon Systech
Mar 2004
P 12/42 Rev 1.0
SSD1800 Series
7.7 VL6, VL5, VL4, VL3, VL2
LCD driving voltages. They can be supplied externally or generated by the internal bias divider. They have the
following relationship:
VL6 > VL5 > VL4 > VL3 > VL2 > Vss
1:4 bias
1:5 bias (default)
4/5 * VL6
VL5
VL4
VL3
VL2
3/4 * VL6
2/4 * VL6
2/4 * VL6
1/4 * VL6
3/5 * VL6
2/5 * VL6
1/5 * VL6
VL6 is the most positive LCD driving voltage. It can be supplied externally or generated by the internal regulator. It is
recommended to add a capacitor between VL6 and Vss for external regulator.
7.8 VF
This pin is the input of the built-in voltage regulator. When external resistor network is selected to generate the
LCD driving level, VL6, two external resistors, R1 and R2, are connected between AVSS and VF, and VF and VL6,
respectively (see application circuit)
7.9 REF
This pin is to select the input voltage of internal voltage regulator. This pin is need to pulled low for normal
internal voltage regulator operation.
7.10 DIRS
This pin controls the direction of Segment.
When DIRS = Low
SEG0 -> SEG2 -> ..... -> SEG78 -> SEG79
When DIRS = High
SEG79 -> SEG78 -> ..... -> SEG1 -> SEG0
7.11 CLK
External clock input. It must be fixed to high or low when the internal oscillation circuit is used. In case of the
external clock mode, CLK is used as the clock and OSC bit should be OFF.
7.12 P/S
This pin is serial/ parallel interface selection input. When this pin is pulled high, parallel mode is selected. When it
is pulled low, serial interface will be selected. Read back operation is only available in parallel mode.
7.13 DL
This pin is to select the data length for parallel data input.
When P/ S = Low
DL = Low or High: serial interface mode
When P/ S = High
DL = Low: 4-bit bus mode
DL = High: 8-bit bus mode
This pin must be fixed to high or low in serial mode.
SSD1800 Series Rev 1.0
P 13/42 Mar 2004
Solomon Systech
7.14 C68/80
This pin is microprocessor interface selection input. When the pin is pulled high, 6800 series interface is selected
and when the pin is pulled low, 8080 series MCU interface is selected. This pin must be fixed to high or low in serial
mode.
7.15 RES
This pin is reset signal input. Initialization of the chip is started once this pin is pulled low. Minimum pulse width for
completing the reset is 10ms.
7.16 TEST
Test pin. This pin is not used for normal operation. Leave this pin open (NC).
7.17 C1P, C1N, C2P and C2N
When internal DC-DC voltage converter is used, external capacitors are connected between these pins. Different
connection will result in different DC-DC converter multiple factor, 2x/3x. Details connections please refer to Figure
12.
7.18 COMI0, COMI1
There are two icons pins (pin47 and 140). Both pins output exactly the same signal. The reason for duplicating the
pin is to enhance the flexibility of the LCD layout.
7.19 COM0 – COM15
These pins provide the common driving signal COM0 – COM15 to the LCD panel. Their output voltage levels are
AVss during sleep mode and standby mode.
7.20 SEG0 - SEG79
These pins provide the LCD segment driving signals. Their output voltage levels are AVSS during sleep mode and
standby mode.
7.21 NC
These are the No Connection pins. Nothing should be connected to these pins, nor they are connected together.
These pins should be left open individually.
Solomon Systech
Mar 2004
P 14/42 Rev 1.0
SSD1800 Series
8
FUNCTIONAL BLOCK DESCRIPTIONS
8.1 Command Decoder and Command Interface
This module determines whether the input data is interpreted as data or command. Data is directed to this module
based upon the input of the D/ C pin. If D/ C is high, data is written to internal memories (DDRAM, CGRAM,
ICONRAM). If D/ C is low, the input at D7-D0 is interpreted as a Command and it will be decoded and be written to
the corresponding command register.
8.2 MPU Parallel 6800-series Interface in 8 bits bus mode
The parallel interface consists of 8 bi-directional data pins (D7-D0), R/W ( WR ), D/ C , E(RD ), CS . R/W ( WR )
input high indicates a read operation from the internal RAM (DDRAM, CGRAM and ICONRAM). R/W ( WR ) input low
indicates a write operation to internal RAM (DDRAM, CGRAM and ICONRAM) or Internal Command Registers
depending on the status of D/ C input. The E(RD ) input serves as data latch signal (clock) when high provided that
CS are low. Refer to Figure 20 for Parallel Interface Timing Diagram of 6800-series microprocessors.
In order to match the operating frequency of display RAM with that of the microprocessor, some pipeline
processings are internally performed which require the insertion of a dummy read before the first actual display data
read. This is shown in Figure 4 below. The dummy read make the address counter (AC) increased by 1. So it is
recommended to set address again before writing. The consecutive read after the dummy read are also the valid
data. The instruction read cycle is not supported and it is regarded as a no operation cycle.
8.3 MPU Parallel 8080-series Interface in 8 bits bus mode
The parallel interface consists of 8 bi-directional data pins (D7-D0), R/W ( WR ), D/ C , E(RD ), CS . E(RD ) input
serves as data read latch signal (clock) when low provided that CS is low whether it is Command write or internal
RAM read/ write is controlled by D/ C . R/W ( WR ) input serves as data write latch signal (clock) when low provided
that CS is low. Refer to Figure 21 for Parallel Interface Timing Diagram of 8080-series microprocessor.
Similar to 6800-series interface, a dummy read is also required before the first actual display data read.
8.4 4-bit MPU Parallel 6800/8080-Series Interface
The control of 4-bit bus mode is exactly the same as 8-bit bus mode except 2 consecutive access (read/ write) is
needed to read/ write 8 bits data. For write operation, upper order bits are written before the low order bits, and low
order bits are always read before the upper order bit in read transaction.
8.5 MPU Serial Interface
The serial interface consists of serial clock SCK (D6), serial data SDA (D7), D/ C , CS . SDA is shifted into a 8-bit
shift register on every rising edge of SCK in the order of D7, D6, ... D0. D/ C is sampled on every eighth clock to
determine whether the data byte in the shift register is written to the internal RAM (DDRAM, CGRAM, ICONRAM) or
command register at the same clock.
8.6 Oscillator Circuit
This module is an On-Chip low power RC oscillator circuitry. The oscillator generates the clock for the DC-DC
voltage converter. This clock is also used in the Display Timing Generator.
SSD1800 Series Rev 1.0
P 15/42 Mar 2004
Solomon Systech
8.7 ADDRESS COUNTER (AC)
Address Counter (AC) in SSD1800 stores DDRAM/ CGRAM/ ICONRAM address. After writing into or reading
from DDRAM/ CGRAM/ ICONRAM. AC is automatically increased by 1. There is only one address counter and stores
the address among DDRAM / CGRAM / ICONRAM.
DL
C68/80
CS
D/C
R/W (WR)
E(RD)
Valid Data
D7 ~ D0
Instruction
Write
NOP
Dummy
Read
RAM
Read
Data
Write
Figure 4 - Timing Diagram of 8-bit Parallel Bus Mode Data Transfer (6800 MPU Mode)
DL
C68/80
CS
D/C
R/W (WR)
E(RD)
Valid Data
D7 ~ D0
Instruction
Write
NOP
Dummy
Read
RAM
Read
Data
Write
Figure 5 - Timing Diagram of 8-bit Parallel Bus Mode Data Transfer (8080 MPU Mode)
Solomon Systech
Mar 2004
P 16/42 Rev 1.0
SSD1800 Series
DL
C68/80
CS
D/C
R/W (WR)
E(RD)
Lower
4-bits
Upper
4-bits
Lower
4-bits
Upper
4-bits
Upper
4-bits
Lower
4-bits
D7 ~ D0
Write
Instruction
NOP
Dummy Read
RAM Read Data Write
Figure 6 - Timing Diagram of 4-bit Parallel Bus Mode Data Transfer (6800 MPU Mode)
DL
C68/80
CS
D/C
R/W (WR)
E(RD)
Upper
4-bits
Lower
4-bits
Lower
4-bits
Upper
4-bits
Upper
4-bits
Lower
4-bits
D7 ~ D0
Write
Instruction
NOP
Dummy Read
RAM Read Data Write
Figure 7 - Timing Diagram of 4-bit Parallel Bus Mode Data Transfer (8080 MPU Mode)
CS
SDA(D7)
D7 D6 D5 D4 D3 D2 D1 D0 D7
SCK(D6)
D/C
1
2
3
4
5
6
7
8
9
Figure 8 – Timing Diagram of Serial Data Transfer
SSD1800 Series Rev 1.0
P 17/42 Mar 2004
Solomon Systech
8.8 Display Data RAM (DDRAM)
DDRAM stores display data of maximum 64 x 8 bits (Max 64 characters). DDRAM address is set in the address
counter as a hexadecimal number.
st
th
Figure 9 - DDRAM Address
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F
20 22 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F
30 33 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F
COM0 – COM7
COM8 – COM15
Hidden Line
Hidden Line
(1) DDRAM Address
8.9 SEGMENT ICON RAM (ICONRAM)
ICONRAM has segment control data and segment pattern data. There are 2 ICONS pins (COMI0 & COMI1), which
have the same signal. So the icons on the same SEG are displayed at the same time. The number of icons is 80.
Table 4 - Relationship between ICONRAM Address and Display Pattern
ICONRAM address
ICONRAM bits
D7
D6
D5
D4
S0
D3
S1
D2
S2
D1
S3
D0
S4
00h
-
-
-
-
-
-
01h
S5
S6
S7
S8
S9
02h
-
-
-
S10
…
S11
…
S12
…
S13
…
S14
…
…
…
-
…
-
…
-
0Dh
S65
S70
S75
S66
S71
S76
S67
S72
S77
S68
S73
S78
S69
S74
S79
0Eh
0Fh
-
-
-
-
-
-
Note: “-“: Don’t care.
8.10 Character Generator ROM (CGROM)
CGROM has 5 x 8 dot 256 characters. The Function Set instruction selects the 8 characters (00h - 07h) of CGROM
or CGRAM.
Solomon Systech
Mar 2004
P 18/42 Rev 1.0
SSD1800 Series
Table 5 - CGROM Character Code
Note: The CGROM 0000xxxx are empty.
SSD1800 Series Rev 1.0
P 19/42 Mar 2004
Solomon Systech
8.11 Character Generator RAM (CGRAM)
CGRAM has up to 5 x 8 dots 8 characters. By writing font data to CGRAM, user defined character can be used.
CGRAM can be written regardless of Function Set instruction.
Table 6 - Relationship between Character Code (DDRAM) and Character Pattern (CGRAM)
CGRAM address
ICONRAM bits
D7 D6 D5
Character Code
(DDRAM data)
D4
X
D3
X
D2
X
D1
X
D0
X
00h (Pattern 0)
01h (Pattern 1)
02h (Pattern 2)
03h (Pattern 3)
04h (Pattern 4)
05h (Pattern 5)
40h
41h
42h
43h
44h
45h
46h
47h
48h
49h
4Ah
4Bh
4Ch
4Dh
4Eh
4Fh
50h
51h
52h
53h
54h
55h
56h
57h
58h
59h
5Ah
5Bh
5Ch
5Dh
5Eh
5Fh
60h
61h
62h
63h
64h
65h
66h
67h
68h
69h
6Ah
6Bh
6Ch
6Dh
6Eh
6Fh
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Solomon Systech
Mar 2004
P 20/42 Rev 1.0
SSD1800 Series
Character Code CGRAM address
(DDRAM data)
ICONRAM bits
D7 D6 D5
D4
X
D3
X
D2
X
D1
X
D0
X
06h (Pattern 6)
70h
71h
72h
73h
74h
75h
76h
77h
78h
79h
7Ah
7Bh
7Ch
7Dh
7Eh
7Fh
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
07h (Pattern 7)
-
-
-
-
-
-
-
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
NOTE: “-” Don’t use
“X” Pattern 0 or 1
8.12 LCD Driving Voltage Generator and Regulator
This module generates the LCD voltage required for display driving output. It takes a single supply input and
generates necessary voltage levels. This block consists of:
1. 2x/3x DC-DC voltage converter
The built-in Regulated DC-DC voltage converter is used to generate
positive LCD driving voltage with internal voltage reference, VREF, relative to AVSS
AVDD
AVDD
SSD1800
AVDD
SSD1800
AVDD
R2
C1P
C1N
C1P
C1N
C2P
+
+
C2
C2
C2
C1
VF
C1
+
VL6
+
DC-DC
+
+
C2P
Converter
C2
C2N
VL6
VL6
+
-
VREF
AVss
R1
3x DC-DC Converter 2x DC-DC Converter
Remarks:
C1 = 2.2µF - 4.7µF
C2 = 0.1µF - 1µF
Remarks:
R1 and R2 = 500K-2.5M ohms
Figure 10 – Configurations for DC-DC Converter
Figure 11 - Configurations for Voltage Regulator
SSD1800 Series Rev 1.0
P 21/42 Mar 2004
Solomon Systech
2. Voltage Regulator
The feedback gain control for LCD driving contrast can be adjusted by using reference voltage and external
resistor network. The reference voltage is supplied by internal Vref and Ref should be connected to low for normal
operation of internal voltage reference Vref. The external resistors are required to be connected between AVSS and
VF (R1), and between VF and VL6 (R2). The following equations are used to calculate the regulator output voltages.
R2
R1
VL6 = 1+
×VREF
AND
VREF = 2V 0.06
3. Contrast Control
Software control of the 32 contrast voltage levels at each voltage regulator feedback gain. The equation of calculating
the LCD driving voltage is given as:
R2
R1
n
150
VL6 = 1+
×VREF × 1−
where n is set in contrast control register.
Table 7- Contrast Control Register
X6 X5 X4 X3 X2 X1 X0
No.
1
X7
n
VL6
Contrast
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0
0
0
0
.
0
0
0
0
.
0
0
0
0
.
0
0
1
1
.
0
1
0
1
.
0 (default) Maximum
High
2
1
2
.
.
.
.
.
.
.
.
.
3
.
4
3
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
31
32
1
1
1
1
1
1
1
1
0
1
30
31
.
Minimum
Low
(“ - “: Don’t care)
4. Bias Divider
Divide the regulator output to give the LCD driving voltages (VL5-VL2). A low power consumption circuit design in
this bias divider saves most of the display current comparing to traditional design.
5. Bias Ratio Selection circuitry
Software control of 1/4 and 1/5 bias ratio to match the characteristic of LCD panel.
Solomon Systech
Mar 2004
P 22/42 Rev 1.0
SSD1800 Series
8.13 Reset Circuit
This block includes Power On Reset circuitry and the Reset pin RES . Both of these having the same reset
function. Once RES receives a negative reset pulse, all internal circuitry will start to initialize. Minimum pulse width
for completing the reset sequence is 10ms.
The status of the chip after reset is given by:
1. Display/ cursor/ blink is turned OFF
2. 2-line display mode
3. Power control register is set to 000b
4. Oscillator is OFF
5. Power save is OFF
6. CGRAM is not used
7. Shift register data clear in serial interface
8. Bias ratio is set to 1/5
9. Address counter is set to 00h
10. Normal scan direction of the COM outputs
11. Contrast control register is set to 00h
12. Test mode is turned OFF
13. In case of 4-bit interface mode selection, SSD1800 considers the 1st 4-bit data from MPU as the
high order bits.
14. The 1st line of display is the address 00h-0Fh.
8.14 Display Data Latch
A series of registers carrying the display signal information. For SSD1800, there are 105 latches (80 + 25) for
holding the data, which will be fed to the HV Buffer Cell and Level Selector to output the required voltage levels.
8.15 Level Selector
Level Selector is a control of the display synchronization. Display voltage can be separated into two sets and
used with different cycles. Synchronization is important since it selects the required LCD voltage level to the HV
Buffer Cell, which in turn outputs the COM or SEG LCD waveform.
8.16 HV Buffer Cell (Level Shifter)
Buffer Cell work as a level shifter, which translates the low voltage output signal to the required, driving voltage.
The output is shifted out with an internal FRM clock that comes from the Display Timing Generator. The voltage
levels are given by the level selector that is synchronized with the internal M signal.
SSD1800 Series Rev 1.0
P 23/42 Mar 2004
Solomon Systech
9
VOLTAGE GENERATOR CIRCUIT
VDD
VDD
AVDD
AVDD
C1P
+
C1P
+
C2
C2
C1N
C1
C1
C2
C1N
C2P
+
+
+
+
C2P
C2N
C2
VL6
VF
VL6
VF
R1
R1
R2
R2
GND
VL6
VL5
VL4
VL3
VL2
AVSS
GND
VL6
VL5
VL4
VL3
VL2
GND
GND
3x DC-DC Converter
2x DC-DC Converter
Remarks:
(VC,VF = 1,1)
C1 = 2.2µF - 4.7µF
C2 = 0.1µF - 1µF
Note: VC, VF = bit X2 and X0 in the command of Power Control Register;
X2 is the bit of turns on/off of the internal voltage converter and regulator
X0 is the bit of turns on/off of the voltage divider
R1 and R2 = 500K-2.5M ohms
Figure 12 - When Built-in Power Supply is used
VDD
VDD
AVDD
AVDD
C1P
C1N
C1P
C1N
C2P
C2N
C2P
C2N
VF
VF
-
+
E xte rn al
E xte rna l
P owe r
VL6
VL5
VL4
VL3
VL2
VL6
VL5
VL4
VL3
VL2
P owe r
S up ply
C2
S up p ly
AVSS
AVSS
GND
GND
(VC, V F = 0 ,1)
(VC, VF = 0 ,0 )
All Capacitor is C2.
C2 : 0.1 uF
in
Note: VC, VF = X2 , X0
Power Control Register
Figure 13 When External Power Supply is used
Solomon Systech
Mar 2004
P 24/42 Rev 1.0
SSD1800 Series
10 FRAME FREQUENCY
1/17 Duty
SSD1800 Series Rev 1.0
P 25/42 Mar 2004
Solomon Systech
11 COMMAND TABLE
Table 8 - Command Table
D/C
Hex
D7 D6 D5 D4 D3
D2
D1
D0
Command
Return Home
Description
DDRAM address is set to 00h from address counter and
the cursor returns to 00h position
0
02
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
1
0
The contents of DDRAM are not changed.
Set Double Height
Mode
X1X0 = 00: normal display (POR)
X1X0 = 01: COM0 - COM15 is double height
X1X0 = 10/11: normal display
0
0
08 – 0B
0C – 0F
0
1
X1
X1
X0
X0
Set Power Save
Mode / Oscillator
Control
X0 = 0: power save OFF (POR)
X0 = 1: power save ON
X1 = 0: oscillator OFF (POR)
X1 = 1: oscillator ON
Function Set
X0 = 0: CGROM is selected (POR)
X0 = 1: CGRAM is selected
X1 = 0: COM0 -> COM15 (POR)
X1 = 1: COM15 -> COM0
0
0
10 – 13
18 – 1B
0
0
0
0
0
0
1
1
0
1
0
0
X1
X1
X0
X0
Set Display Start
Line
X1X0 = 00: DDRAM line 1 shows at the first line of LCD
(POR).
X1X0 = 01: DDRAM line 2 shows at the first line of LCD.
X1X0 = 10: DDRAM line 3 shows at the first line of LCD.
X1X0 = 11: DDRAM line 4 shows at the first line of LCD.
Set Bias Control
X0 = 0: 1/5 bias (POR)
0
0
1C – 1D
20 – 27
0
0
0
0
0
1
1
0
1
0
1
*
X0
X0
X0 = 1: 1/4 bias
Set Power Control
Register
X0 = 0: turns off the voltage divider (POR)
X0 = 1: turns on the voltage divider
X1 : Don’t care
X2
X1
X2 = 0: turns off the internal voltage converter and
regulator (POR)
X2 = 1: turns on the internal voltage converter and
regulator
Set Display Control X0 = 0: turns off the display (POR)
X0 = 1: turns on the display
X1 = 0: blink off (POR)
0
28 – 2F
0
0
1
0
1
X2
X1
X0
X1 = 1: blink on
X2 = 0: cursor off (POR)
X2 = 1: cursor on
Set DD/CGRAM
address
DDRAM/ CGRAM address range:
0
0
80 – FF
40 – 5F
1
0
X6 X5 X4 X3
X2
X2
X1
X1
X0
X0
DDRAM: 00h - 3Fh
CGRAM: 40h - 7Fh
Set ICONRAM
address / Contrast
Control
ICONRAM address range / Contrast Control Register:
1
0
X4
X3
ICONRAM: 00h - 0Fh
Contrast Control Register: 10h
TE: 11h (test byte)
NOP
Set Test Mode
Command for No Operation
Reserved for IC testing. Do Not use
0
0
00
30
0
0
0
0
0
1
0
1
0
*
0
*
0
*
0
*
Note:
1. Patterns other than that given in Command Table are prohibited to enter to the chip as a command. Otherwise, unexpected result
will occur.
2. “*” : Don’t care.
Solomon Systech
Mar 2004
P 26/42 Rev 1.0
SSD1800 Series
Data Read/ Write
To read data from the internal memories (DDRAM/ CGRAM/ ICONRAM), input high to R/W ( WR ) pin and D/ C
pin for 6800-series parallel mode, low to E(RD ) pin and high to D/ C pin for 8080-series parallel mode. No data read
is provided for serial mode. In normal mode, address counter will be increased by one automatically after each data
read. A dummy read is required before the first data read. See Figure 4 in Functional Description.
To write data to the internal memories (DDRAM/ CGRAM/ ICONRAM), input low to R/W ( WR ) pin and high to
D/ C pin for 6800-series and 8080-series parallel mode. For serial interface, it will always be in write mode. Address
counter will be increased by one automatically after each data write.
SSD1800 Series Rev 1.0
P 27/42 Mar 2004
Solomon Systech
12 COMMAND DESCRIPTIONS
12.1 Return Home
Return Home instruction field makes cursor return home. DDRAM address is set to 00h from address counter
and the cursor returns to 00h position. The contents of DDRAM are not changed.
12.2 Set Double Height Mode
This command increases the height of one character line from 8 to 16 dots. If the number of COM signal needed
exceeds the existing COM signal, the last character line will not be displayed. It will happen at following case:
1. For X1X0 = 01, where COM0-COM15 is double height.
The 2nd line will not be displayed.
Figure 14– Function set command (X1X0 = 00)
Figure 15 - COM0 ~ COM15 is a Double Height Line in function set command (X1X0 = 01)
Solomon Systech
Mar 2004
P 28/42 Rev 1.0
SSD1800 Series
12.3 Set Power Save Mode / Oscillator Control
To enter Standby or Sleep Mode, it should be done by turning off the internal oscillator and turning on the power
save control bit. The corresponding control bits are X1X0 = 01. In order to put the system into low power consumption
mode, internal voltage converter, voltage regulator and voltage divider should also be turned off by using Power
Control Register. After putting the system into power save mode, the following status will be entered:
1. Internal oscillator and LCD power supply circuits are stopped.
2. Segment and Common drivers output AVSS level.
3. The display data and operation mode before sleep are held. All the internal circuit is stopped.
12.4 Function Set
This command sets 2 functions on the system. They are COM shift direction (left or right) and CGROM/ CGRAM
character area select.
12.5 Set Display Start Line
This command is to set Display Start Line register to determine starting address of display data RAM to be
displayed by selecting a value from 0 to 3. With the value equals to 0, the display will start from address (00h-0Fh).
With the value equals to 1, the display will start from address (10h-1Fh). With the value equals to 2, the display will
start from address (20h-2Fh). With the value equals to 3, the display will start from address (30-3Fh).
12.6 Set Bias Control
Bias ratio 1/4 or 1/5 could be set using this command. When changing the number of line display, the bias ratio
also needs to be adjusted to make display contrast consistent.
12.7 Set Power Control Register
This command turns on / off the various power circuits associated with the chip which including regulated DC-DC
converter and voltage divider.
12.8 Set Display Control
This command provides 3 display functions. It turns on/off of the cursor, blink and display. When both cursor and
blink control bit set high, the driver make LCD alternate between inverting display character and normal display
character at the cursor position with about a half second. On the contrary, if cursor control bit is low, only a normal
character is displayed regardless of blink control bit.
SSD1800 Series Rev 1.0
P 29/42 Mar 2004
Solomon Systech
Display State
X2, X1
1, 0 (Cursor Mode)
1, 1 (Blinking Mode)
0, 0
0, 1
Figure 16 - Display Attributes
Solomon Systech
Mar 2004
P 30/42 Rev 1.0
SSD1800 Series
12.9 Set DD/ CGRAM Address
Before writing/ reading data into/ from the RAM, set the address by RAM address set instruction. Next, when
data are written/ read in succession, the address is automatically increased by1. After accessing 7Fh, the address is
00h.
Table 9 - DD/ CGRAM Address Mapping
ADDRESS
00H
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
DDRAM LINE 1 (00H - 0FH)
DDRAM LINE 2 (10H - 1FH)
DDRAM LINE 3 (20H - 2FH)
DDRAM LINE 4 (30H - 3FH)
CGRAM (PATTERN 0)
10H
20H
30H
40H
CGRAM (PATTERN 1)
CGRAM (PATTERN 3)
CGRAM (PATTERN 5)
CGRAM (PATTERN 7)
50H
CGRAM (PATTERN 2)
60H
CGRAM (PATTERN 4)
70H
CGRAM (PATTERN 6)
SSD1800 Series Rev 1.0
P 31/42 Mar 2004
Solomon Systech
12.10 Set ICONRAM Address Set
Before writing/ reading data into/ from the ICONRAM, set the address by ICONRAM Address Set instruction.
Next, when data are written/ read in succession, the address is automatically increased by 1. The 5 icons at a time
can blink if blinking is enabled. The blink attributes of ICON are the same as the cursor blink. For accessing DD/
CGRAM, the DD/ CGRAM Address Set instruction should be set before. After accessing 0Fh, the address of
ICONRAM address is 00h. The ICONRAM address ranges are 00h-0Fh.
Table 10 - ICONRAM Address Mapping
ADDRESS
00H
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
ICONRAM (00h - 0Fh)
C
T
E
C
10H
Reserved
R
12.11 Set Contrast Control Register
Set the Contrast Control Register (CCR) by ICONRAM Address Set Instruction. Next, data are written to the
CCR. The default value of CCR is (00000).
TE: Test Mode Register (Do not Use) (11H)
When the CCR and TE registers are written, the address counter is not increased.
12.12 NOP
A command causing No Operation.
12.13 Set Test Mode
This command forces the driver chip into its test mode for internal testing of the chip. Under normal operation, user
should NOT use this command.
Solomon Systech
Mar 2004
P 32/42 Rev 1.0
SSD1800 Series
13 MAXIMUM RATINGS
Table 11 - Maximum Ratings (Voltage Reference to VSS)
Symbol
Parameter
Supply Voltage
Value
Unit
AVDD, DVDD
-0.3 to +4.0V
V
VL6
VIN
VLCD Voltage
Input Voltage
-0.3 to +6.5V
V
V
VSS-0.3 to
VDD+0.3
TA
Operating Temperature
-30 to +85
°C
°C
Tstg
Storage Temperature Range
-65 to +150
* Maximum Ratings are those values beyond which damage to the device may occur. Functional
operation should be restricted to the limits in the Electrical Characteristics tables or Pin Description
section
This device contains circuitry to protect the inputs against damage due to high static voltages or electric
fields; however, it is advised that normal precautions to be taken to avoid application of any voltage
higher than maximum rated voltages to this high impedance circuit. For proper operation it is
recommended that Vin and VL6 be constrained to the range VSS < or = (Vin) < or = VDD.
Reliability of operation is enhanced if unused inputs are connected to an appropriate logic voltage level
(e.g., either Vss or VDD). Unused outputs must be left open. This device may be light sensitive. Caution
should be taken to avoid exposure of this device to any light source during normal operation. This device
is not radiation protected.
SSD1800 Series Rev 1.0
P 33/42 Mar 2004
Solomon Systech
14 DC CHARACTERISTICS
Table 12 - DC Characteristics (Unless otherwise specified, Voltage Referenced to VSS, VDD = 2.4 to
3.6V, TA = -30 to 85°C.)
Symbol
Parameter
Test Condition
Min
Typ
Max
Unit
DVDD
AVDD
IDD1
Logic and Analog Circuit
Supply Voltage Range
Display Operation Supply
Current Drain
(Absolute value referenced to
DVss and AVss)
2.4
2.7
3.6
V
VDD = 3V, TA = 25°C
VLCD = 5.8V without load
No access from MPU
-
-
-
-
-
-
85
500
5
µA
µA
µA
IDD2
ISB
Access operation from MPU
Supply Current Drain
VDD = 3V, TA = 25°C
fcyc = 200kHz
Standby Mode Supply Current
Current No load
Oscillator OFF
Power Save ON
VLCD = VL6 - VSS
TA = 25°C, C = 1uF
VLCD
VL6
VIH
LCD Driving Voltage Input
Voltage Regulator Output
Logic High Input Voltage
4
4
-
-
-
5.8
5.8
DVDD
V
V
V
V
0.8*DVDD
VIL
Logic Low Input Voltage
Logic High Output Voltage
Logic Low Output Voltage
0
-
-
-
-
0.2*DVDD
VOH
VOL
VL6
IOH = -1mA, VDD = 2.4V
IOL = 1mA, VDD = 2.4V
DVDD – 0.4
-
-
V
V
V
0.4
5.8
LCD Driving Voltage Source
(VL6)
Regulator Enable (VL6 voltage
depends on contrast control/
external resistors network)
AVSS - 0.5
VL6
LCD Driving Voltage Source
(VL6)
Regulator Disable
-
Floating
-
V
VL6
VL5
VL4
VL3
VL2
LCD Display Voltage Output
(V L5, VL4, VL3, VL2)
Voltage reference to AVSS,
Bias Divider Enabled, 1:a
bias ratio
VL6
-
-
-
-
-
-
-
-
-
-
V
V
V
V
V
(a-1)/a * VL6
(a-2)/a * VL6
2/a * VL6
1/a * VL6
VL6
VL5
VL4
VL3
VL2
-
-
-
-
-
Voltage reference to AVSS,
External Voltage Generator,
Bias Divider Disable
LCD Display Voltage Output
(V L5, VL4, VL3, VL2)
VL5
VL4
VL3
VL2
VSS
5.8
VL6
VL5
VL4
VL3
V
V
V
V
V
IOH
IOL
IOZ
Logic High Output Current
Source
VOUT = VDD - 0.4V
VOUT = 0.4V
50
-
-
-
-
-50
1
µA
µA
µA
Logic Low Output Current
Drain
-
-1
Logic Output Tri-state Current
Drain Source
IIL/ IIH
CIN
Logic Input Current
-1
-
-
5
2
1
µA
Logic Pins Input Capacitance
7.5
2.06
PF
Vref
Voltage regulator reference
voltage
1.94
V
Solomon Systech
Mar 2004
P 34/42 Rev 1.0
SSD1800 Series
15 AC CHARACTERISTICS
Table 13 - AC Characteristics (Unless otherwise specified, Voltage Referenced to VSS, VDD = 2.4 to
3.6V, TA = -30 to 85°C.)
Symbol
Parameter
Test Condition
Min
Typ
Max
Unit
FFRM
Frame Frequency
Internal Oscillator
VDD = 3V, TA = 25°C
67.5
75
90
Hz
Table 14 - 6800-Series MPU Parallel Interface Timing Characteristics (VDD - VSS = 2.4 to 3.6V, TA =
-30 to 85°C)
Symbol
tcycle
tAS
Parameter
Min
650
60
30
100
50
50
-
Typ
Max
-
-
-
-
Unit
ns
ns
Ns
Ns
Ns
ns
Clock Cycle Time
Address Setup Time
Address Hold Time
Write Data Setup Time
Write Data Hold Time
Read Data Hold Time
Output Disable Time
Access Time
-
-
-
-
-
-
-
-
tAH
tDSW
tDHW
tDHR
tOH
-
-
70
100
ns
ns
tACC
-
150
150
450
450
-
-
-
-
-
-
-
-
ns
ns
ns
ns
E(RD ) Low Pulse Width (read)
E(RD ) Low Pulse Width (write)
E(RD ) High Pulse Width (read)
E(RD ) High Pulse Width (write)
Rise Time
PWEL
PWEH
tR
tF
-
-
-
-
25
25
ns
ns
Fall Time
Figure 17– 6800-series MCU Parallel Interface Waveform
SSD1800 Series Rev 1.0
P 35/42 Mar 2004
Solomon Systech
Table 15 - 8080-Series MPU Parallel Interface Timing Characteristics (VDD - VSS = 2.4 to 3.6V, TA =
-30 to 85°C)
Symbol
tcycle
tAS
Parameter
Min
650
60
30
100
50
50
-
Typ
Max
-
-
-
-
Unit
ns
ns
ns
ns
ns
ns
ns
ns
Clock Cycle Time
Address Setup Time
Address Hold Time
Write Data Setup Time
Write Data Hold Time
Read Data Hold Time
Output Disable Time
Access Time
-
-
-
-
-
-
-
-
tAH
tDSW
tDHW
tDHR
tOH
-
-
70
100
tACC
-
450
450
150
150
-
-
-
-
-
-
-
-
ns
ns
ns
ns
WR Low Pulse Width (read)
WR Low Pulse Width (write)
WR High Pulse Width (read)
WR High Pulse Width (write)
Rise Time
PWWRL
PWWRH
tR
tF
-
-
-
-
25
25
ns
ns
Fall Time
Figure 18– 8080-series MCU Parallel Interface Waveform
Solomon Systech
Mar 2004
P 36/42 Rev 1.0
SSD1800 Series
Table 16 - Serial Interface Timing Characteristics (VDD - VSS = 2.4 to 3.6V, TA = -30 to 85°C)
Symbol
tcycle
tAS
Parameter
Min
1000
50
300
150
700
50
Typ
Max
-
-
-
-
-
-
-
-
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Clock Cycle Time
Address Setup Time
Address Hold Time
Chip Select Setup Time
Chip Select Hold Time
Write Data Setup Time
Write Data Hold Time
Clock Low Time
Clock High Time
Rise Time
-
-
-
-
-
-
-
-
-
-
-
tAH
tCSS
tCSH
tDSW
tDHW
tCLKL
tCLKH
tR
50
300
300
-
-
25
25
tF
Fall Time
-
Figure 19– Serial Interface Characteristics
SSD1800 Series Rev 1.0
P 37/42 Mar 2004
Solomon Systech
16 APPLICATION EXAMPLES
COMI0
COM0
COM1
COM8
:
COM9
..
:
.
:
.
DISPLAY PANEL SIZE
80 X 16 + 1 ICON LINE
COM14
.
.
:
COM6
COM7
COM15
.
.
COMI1
SEG0…………………………………………………………SEG79
SEG79……………………………………………………………………………SEG0
COMI1
.
COM7
.
COM6
.
COM5
SSD1800 IC
16 MUX
COM15
COM14
:
:
:
.
(DIE FACE IP)
:
.
COM9
COM8
COM0
COMI0
DVDD VL2 VL3 VL4 VL5 VL6
AVDD
0.1uF +
External Power Supply
VDD=3.0V
AVSS
Logic pin connections not specified above:
Pins connected to DVdd: C68/ 80 , P/ S , DL, DIRS
Pins connected to DVss: REF, CLK
Figure 20- Application Circuit: External Regulator with internal divider mode (8-bit 6800 mode)
Solomon Systech
Mar 2004
P 38/42 Rev 1.0
SSD1800 Series
COM8
COMI0
COM9
COM0
:
COM1
:
:
COM14
:
COM15
.
DISPLAY PANEL SIZE
80 X 16 + 1 ICON LINE
:
.
:
.
.
.
.
COM6
COM7
COMI1
SEG0…………………………………………………………SEG79
SEG79……………………………………………………………………………SEG0
COMI1
.
.
COM7
COM6
COM5
:
SSD1800 IC
16 MUX
COM15
COM14
:
:
(DIE FACE IP)
:
COM0
COMI0
COM9
COM8
VL6
C1N C1P C2P
+C1 C2 C2
DVDD VL2 VL3 VL4 VL5 VL6
VF
R2
AVDD
+
+
R1
C1: 2.2 -4.7 uF
C2: 0.1-1uF
AVDD
VDD = 3.0V
AVSS
Remarks:
R1 and R2 = 500K-2.5M ohms
Note:
It is recommended to use 2x regulated DC-DC
converter to reduce the current consumption
under certain of condition.
Logic pin connections not specified above:
Pins connected to DVdd: DL, DIRS
Pins connected to DVss: REF, CLK, P/ S , R/W ( WR ),
e.g. AVDD /DVDD = 3.0V and VLCD (LCD driving
E(/RD), C68/ 80 , D5-D0
voltage) = 5.0V.
Figure 21 - Application Circuit: ALL internal power mode with 2x regulated DC-DC converter
(serial mode)
SSD1800 Series Rev 1.0
P 39/42 Mar 2004
Solomon Systech
COMI0
COM0
COM8
COM1
COM9
:
:
:
DISPLAY PANEL SIZE
80 X 16 + 1 ICON LINE
:
.
COM14
.
COM15
COM6
COM7
:
:
COMI1
SEG0…………………………………………………………SEG79
SEG79……………………………………………………………………………SEG0
COMI1
.
.
COM7
COM15
COM14
:
COM6
COM5
:
SSD1800 IC
16 MUX
:
:
(DIE FACE IP)
COM9
COM8
COM0
COMI0
VL6
C1N C1P C2N C2P
DVDD VL2 VL3 VL4 VL5 VL6
AVDD
VF
R2
+C1 C2
C2
+
+
R1
C1: 2.2 -4.7 uF
C2: 0.1-1uF
AVDD
VDD = 3.0V
Remarks:
AVSS
R1 and R2 = 500K-2.5M ohms
Logic pin connections not specified above:
Pins connected to DVdd: P/ S , DL, DIRS
Pins connected to DVss: REF, CLK, and C68/(80 )
Figure 22- Application Circuit: ALL internal power mode with 3x regulated DC-DC converter
(8-bit 8080 mode)
Solomon Systech
Mar 2004
P 40/42 Rev 1.0
SSD1800 Series
Recommended INITIALIZING of SSD1800
NOTE:
At instructions 1-6, the minimum clock cycle
time is 650ns for PPI. For details, pls refer
to the SSD1800 datasheet “AC
Characteristics”.
DVDD/AVCC-DVSS/AVSS Power On
At 5 and 6, the internal RAM should be
cleared.
Send reset pulse to the RES pin.
(Recommended minimum reset pulse width is 10ms)
To clear DDRAM, set address at 00h (first
DDRAM) and then write 20h (space
character code) 64times.
Waiting for 10usec
To clear CGRAM, set address at 40h (first
CGRAM) and then write 00h (null data) 64
times
Command Input
1. Function set (000100X1X0)
To clear ICONRAM, set CONRAM address
at 00h (first ICONRAM) and then write 00h
(null data) 16 times
2. Contrast control register setup
3. Power save (power save off; OSC on)
4. Power control (turns on the internal regulator and turns on the
internal divider)
No delay between each Command/Data
input under ideal timing situation (No time
shift in any signals, refer to page 32 for
Command Input
5. RAM address set
Data Input
6. Data writing (RAM clear)
(DDRAM=20h, CG/ICONRAM=00h)
Command Input
7. Display control (turns on the display) (There is an auto mask
off period ~ 260ms)
End of initialization
Figure 23- Recommended INITIALIZING of SSD1800
SSD1800 Series Rev 1.0
P 41/42 Mar 2004
Solomon Systech
Solomon Systech reserves the right to make changes without further notice to any products herein. Solomon Systech makes no warranty,
representation or guarantee regarding the suitability of its products for any particular purpose, nor does Solomon Systech assume any liability arising
out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or
incidental damages. “Typical” parameters can and do vary in different applications. All operating parameters, including “Typical” must be validated for
each customer application by customer’s technical experts. Solomon Systech does not convey any license under its patent rights nor the rights of
others. Solomon Systech products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the
body, or other applications intended to support or sustain life, or for any other application in which the failure of the Solomon Systech product could
create a situation where personal injury or death may occur. Should Buyer purchase or use Solomon Systech products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Solomon Systech and its offices, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or
death associated with such unintended or unauthorized use, even if such claim alleges that Solomon Systech was negligent regarding the design or
manufacture of the part.
http://www.solomon-systech.com
Solomon Systech
Mar 2004
P 42/42 Rev 1.0
SSD1800 Series
相关型号:
©2020 ICPDF网 联系我们和版权申明