HFBR-4503Z [FOXCONN]
Fiber Optic Networking Connector, Multi Mode, Simplex;
| 型号： | HFBR-4503Z |
| 厂家： | 
FOXCONN |
| 描述： | Fiber Optic Networking Connector, Multi Mode, Simplex 连接器 |
| 文件： | 总10页 (文件大小：281K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
HFBR-RXXYYYZ Series (POF)
HFBR-EXXYYYZ Series (POF)
HFBR-CXXYYYZ Series (POF)
Plastic Optical Fiber Cable and Accessories
for Versatile Link
Data Sheet
Cable Description
Features
• Compatible with Avago Versatile Link Family of con-
The HFBR-C/R/EXXYYYZ series of plastic fiber optic cables
are constructed of a single step-index fiber sheathed
in a black polyethylene jacket. The duplex fiber consists
of two simplex fibers joined with a zipcord web.
nectors and fiber optic components
• 1 mm diameter Plastic Optical Fiber (POF) in 3 grades:
-
-
-
CommercialPOFwith0.22dB/mtypicalattenuation
(0°C to 70°C)
Standard (Type="R") and Extra Low Loss (Type="E")
cables comply with UL VW-1 flame retardant specifica-
tion (UL file # E89328) except for Commercial (Type="C")
Standard POF with 0.22 dB/m typical attenuation
(-40°C to 85°C)
High performance Extra Low Loss POF with 0.19
dB/m typical attenuation (-40°C to 85°C).
Cables are available in unconnectored or connectored
options. Refer to the Ordering Guide for part number
information.
500
400
300
Applications
• Industrial data links for factory automation and plant
control
• Intra-system links; board-to-board, rack-to-rack
• Telecommunications switching systems
• Computer-to-peripheral data links, PC bus extension
• Proprietary LANs
• Digitized video
• Medical instruments
• Reduction of lightning and voltage transient suscep-
tibility
200
100
620
640
660
680
700
λ – WAVELENGTH – nm
• High voltage isolation
Figure 1. Typical POF attenuation vs. wavelength.
Plastic Optical Fiber Specifications: HFBR-C/R/EXXYYYZ
Absolute Maximum Ratings
Parameter
Symbol
Min.
-55
-40
-40
0
Max. Unit
+85 °C
+70 °C
+85 °C
+70 °C
+70 °C
+70 °C
Note
Recommended Storage
Temperature
(HFBR-R/EXXYYYZ)
(HFBR-CXXYYYZ)
(HFBR-R/EXXYYYZ)
(HFBR-CXXYYYZ)
(HFBR-R/EXXYYYZ)
(HFBR-CXXYYYZ)
Single Channel
Ts
Ts
To
To
Ti
Ti
FT
FT
r
Recommended Operating
Temperature
Recommended Installation
Temperature
-20
0
1
Short Term Tensile Force
50
N
2
Dual Channel
100
N
Short Term Bend Radius
Long Term Bend Radius
Long Term Tensile Load
Flexing
25
35
mm
mm
N
3, 4
r
FT
1
1000 Cycles 4, 8
UL VW-1 Flame Retardant
Mechanical/Optical Characteristics, TA = -40 to +85°C unless otherwise specified.
Parameter
Symbol
Min.
Typ. [5] Max. Unit
Condition
Cable Attenuation
Source: 660nm LED, 0.5 NA
(HFBR-15xxZ)
Commercial Cable, aO
0.15
0.22
0.22
0.19
0.19
0.19
0.16
0.27 dB/m
TA=-0°C to +70°C
TA=-40°C to +85°C
TA=-40°C to +85°C
TA=-0°C to +70°C
TA=-40°C to +85°C
TA=-40°C to +85°C
>2 meters
Type "C"
Standard Cable,
Type="R"
0.15
0.15
0.12
0.12
0.12
0.27
Length:50m
Extra Low Loss,
Type="E"
0.23
Reference Attenuation
Source: 650nm, 0.5 NA
(monochrometer)
Length:50m
Commercial Cable, aR
Type "C"
0.24 dB/m
0.24
Standard Cable,
Type="R"
Extra Low Loss,
Type="E"
0.19
Numerical Aperture
NA
DC
DJ
0.46
0.94
2.13
0.47
1.00
2.20
5.0
0.50
Diameter, Core and Cladding
Diameter, Jacket
1.06
mm
2.27 mm
ns/m
Simplex Cable
Note 6
Propagation Delay Constant
Mass per Unit Length/Channel
Cable Leakage Current
Refractive Index
l/v
5.3
g/m
Without Connectors
50 kV, l = 0.3 meters
IL
12
nA
Core
n
1.492
1.417
Cladding
Notes:
1. Installation temperature is the range over which the cable can be bent and pulled without damage. Below -20°C the cable becomes brittle and
should not be subjected to mechanical stress.
2. Short Term Tensile Force is for less than 30 minutes.
3. Short Term Bend Radius is for less than 1 hour nonoperating.
4. 90° bend on 25 mm radius mandrel. Bend radius is the radius of the mandrel around which the cable is bent.
5. Typical data are at 25°C.
6. Propagation delay constant is the reciprocal of the group velocity for propagation delay of optical power. Group velocity is v=c/n where c is the
velocity of light in free space (3xl08 m/s) and n is the effective core index of refraction.
7. Note that aR rises at the rate of about 0.0067 dB/°C, where the thermal rise refers to the LED temperature changes above 25°C. Please refer to
Figure 1 which shows the typical plastic optical fiber attenuation versus wavelength at 25°C.
8. Not available for Commercial (Type="C") cable
2
DUPLEX CONNECTOR STYLES
HFBR-4506Z – Duplex
Plastic Fiber Connector Styles
Connector Description
Four connector styles are available for termination of
plastic optical fiber: simplex, simplex latching, duplex
and duplex latching. All connectors provide a snap-in
action when mated to Versatile Link components.
Simplex connectors are color coded to facilitate identi-
fication of transmitter and receiver connections. Duplex
connectors are keyed so that proper orientation is
ensured during insertion. If the POF cable/connector will
be used at extreme operating temperatures or experi-
ence frequent and wide temperature cycling effects, the
cable/connector attachment can be strengthened with
an RTV adhesive (see Plastic Connectoring Instructions
for more detail). The connectors are made of a flame re-
tardant VALOX UL94 V-0 material (UL file # E121562).
HFBR-4526Z
Duplex connectors provide convenient duplex cable
termination and are keyed to prevent incorrect insertion
into duplex configured modules. The duplex connector
is compatible with dual combinations of horizontal, ver-
tical or tilted packages (e.g., two horizontal transmitters,
two vertical receivers, a horizontal transmitter with a
horizontal receiver, etc.). The duplex non-latching con-
nector is available in parchment, off-white (HFBR-4506Z).
HFBR-4516Z – Duplex Latching
SIMPLEX CONNECTOR STYLES
HFBR-4501Z/4511Z – Simplex
, HFBR-4525Z
DUPLEX
CRIMP RING
HFBR-4526Z
The simplex connector provides a quick and stable con-
nection for applications that require a component-to-
connector retention force of 8 Newtons (1.8 lb.). These
connectors are available in gray (HFBR-4501Z) or blue
(HFBR-4511Z). The simplex connector is compatible with
horizontal or vertical or tilted packages.
The duplex latching connector is designed for rugged
applications requiring greater retention force than
the nonlatching duplex connector. When inserting the
duplex latching connector into a module, the connector
latch mechanism should be aligned with the top surface
of the dual combination of horizontal, vertical or tilted
packages. The duplex latching connector is available in
gray (HFBR-4516Z).
HFBR-4503Z/4513Z – Simplex Latching
HFBR-4525Z
Feedthrough/Splice
The simplex latching connector is designed for rugged
applications requiring a greater retention force — 80
Newtons ( 18 lb.) — than provided by a simplex non-
latching connector. When inserting the simplex latching
connector into a module, the connector latch mecha-
nism should be aligned with the top surface of the
horizontal package, or with the tall vertical side of the
vertical package or with top surface of tilted package.
Misalignment of an inserted latching connector into
either module will not result in a positive latch. The con-
nector is released by depressing the rear section of the
connector lever, and then pulling the connector assem-
bly away from the module housing.
HFBR-4505Z/4515Z Bulkhead Adapter
The HFBR-4505Z/4515Z adapter mates two simplex
connectors for panel/bulkhead feedthrough of HFBR-
4501Z/4511Z terminated plastic fiber cable. Maximum
panel thickness is 4.1 mm (0.16 inch). This adapter can
serve as a cable in-line splice using two simplex connec-
tors. The adapters are available in gray (HFBR-4505Z) and
blue (HFBR-4515Z). This adapter is not compatible with
POF duplex, POF simplex latching, or HCS connectors.
The simplex latching connector is available in gray (HF-
BR-4503Z) or blue (HFBR-4513Z).
3
Plastic Optical Fiber Connector Absolute Maximum Ratings
Parameter
Symbol
Min.
-40
-40
0
Max.
85
Unit
°C
Note
Storage and Operating Temperature
Recommended Operating Temperature
Installation Temperature
TS,O
TO
Tl
1
1
1
2
85
°C
70
°C
Nut Torque
HFBR-4505Z/4515Z Adapter
TN
0.7
100
N-m
OzF-in.
Notes:
1. Storage and Operating Temperatures refer to the ranges over which the connectors can be used when not subjected to mechanical stress.
Installation Temperature refers to the ranges over which connectors may be installed onto the fiber and over which connectors can be con-
nected and disconnected from transmitter and receiver modules.
2. Recommended nut torque is 0.57 N-m.
Plastic Optical Fiber Connector Mechanical/Optical Characteristics
T = -40 to +85°C, Unless Otherwise Specified.
A
Parameter
Part Number
Symbol
Min.
Typ.[1]
Max.
Units
Temp. °C
Note
Retention Force,
Connector to
Simplex,
HFBR-4501Z/4511Z
FR-C
7
3
8
N
+25
-40 to +85
2
Versatile Link Transmit-
ters and Receivers
Simplex Latching,
HFBR-4503Z/4513Z
47
11
80
12
80
22
22
+25
-40 to +85
Duplex,
HFBR-4506Z
7
4
+25
-40 to +85
Duplex Latching,
HFBR-4516Z
50
15
+25
-40 to +85
Tensile Force,
Connector to Cable
Simplex,
HFBR-4501Z/4511Z
FT
8.5
N
3
Simplex Latching,
HFBR-4503Z/4513Z
8.5
Duplex, HFBR-4506Z
14
14
35
35
Duplex Latching,
HFBR-4516Z
Adapter Connector
to Connector Loss
HFBR-4505Z/4515Z with
HFBR-4501Z/4511Z
aCC
FR-B
FI
0.7
7
1.5
8
2.8
dB
N
25
4, 5
6
Retention Force
Connector to Adapter
HFBR-4505Z/4515Z with
HFBR-4501Z/4511Z
Insertion Force,
Connector to Versatile
Link Transmitters and
Receivers
Simplex,
HFBR-4501Z/4511Z
8
30
35
N
Simplex Latching,
HFBR-4503Z/4513Z
16
Duplex, HFBR-4506Z
13
22
46
51
Duplex Latching
HFBR-4516Z
Notes:
1. Typical data are at +25°C.
2. No perceivable reduction in retention force was observed after 2000 insertions. Retention force of non-latching connectors is lower at elevated
temperatures. Latching connectors are recommended for applications where a high retention force at high temperatures is desired.
3. For applications where frequent temperature cycling over temperature extremes is expected, please contact Avago Technologies for alternate
connectoring techniques.
4. Minimum and maximum limit for aCC for 0°C to +70°C temperature range. Typical value of aCC is at +25°C.
5. Factory polish or field polish per recommended procedure.
6. Destructive insertion force was typically at 178 N (40 lb.).
4
Step-by-Step Plastic Cable Connectoring Instructions
The following step-by-step guide describes how to termi-
nate plastic fiber optic cable. It is ideal for both field and
factory installation. Connectors can be easily installed
on cable ends with wire strippers, cutters and a crimping
tool.
Finishing the cable is accomplished with the Avago
HFBR-4594ZPolishingKit,consistingofaPolishingFixture,
600 grit abrasive paper and 3 µm pink lapping film (3M
Company, OC3-14). The connector can be used immedi-
ately after polishing.
Step 2
Place the crimp ring and connector over the end of the
cable; the fiber should protrude about 3 mm (0.12 in.)
through the end of the connector. Carefully position the
ring so that it is entirely on the connector with the rim of
the crimp ring flush with the connector, leaving a small
space between the crimp ring and the flange.Then crimp
the ring in place with the crimping tool. One crimp tool is
used for all POF connector crimping requirements.
Materials needed for plastic fiber termination are:
1. Avago Plastic Optical Fiber Cable (Example: HFBR-
RUS500Z, HFBR-RUD500Z, HFBR-EUS500Z, or HFBR-
EUD500Z)
2. Industrial Razor Blade or Wire Cutters
For applications with extreme temperature operation
or frequent temperature cycling, improved connector
to cable attachment can be achieved with the use of an
RTV (GE Company, RTV-128 or Dow Corning 3145-RTV)
adhesive. The RTV is placed into the connector prior to
insertion of the fiber and the fiber is crimped normally.
The connector can be polished after the RTV has cured
and is then ready for use.
3. 16 Gauge Latching Wire Strippers (Example: Ideal
StripmasterTM type 45-092).
4. HFBR-4597Z Crimping Tool
5. HFBR-4594Z Polishing Kit
6. One of the following connectors:
a) HFBR-4501Z/4503Z Gray Simplex/Simplex Latching
Connector and HFBR-4525Z Simplex Crimp Ring
Note: By convention, place the gray connector on the trans
mittercableendandtheblueconnectoronthereceivercable
end to maintain color coding (different color connectors are
mechanically identical).
b) HFBR-4511Z/4513Z Blue Simplex/Simplex Latching
Connector and HFBR-4525Z Simplex Crimp Ring
c)HFBR-4506ZParchment(off-white)DuplexConnector
and HFBR-4526Z Duplex Crimp Ring
Simplex connector crimp rings cannot be used with duplex
connectors and duplex connector crimp rings cannot be
used with simplex connectors because of size differences.
The simplex crimp has a dull luster appearance; the duplex
ring is glossy and has a thinner wall.
d) HFBR-4516Z Gray Latching Duplex Connector and
HFBR-4526Z Duplex Crimp Ring
Step 1
The zip cord structure of the duplex cable permits easy
separation of the channels. The channels should be sepa-
rated a minimum of 100 mm (4 in) to a maximum of 150
mm (6 in) back from the ends to permit connectoring
and polishing.
After cutting the cable to the desired length, strip off
approximately 7 mm (0.3 in.) of the outer jacket with the
16 gauge wire strippers. Excess webbing on the duplex
cable may have to be trimmed to allow the simplex or
simplex latching connector to slide over the cable.
When using the duplex connector and duplex cable, the
separatedduplexcablemustbestrippedtoequallengths
on each cable. This allows easy and proper seating of the
cable into the duplex connector.
5
Step 4
Placetheflushconnectorandpolishingfixtureonthedull
side of the 3 µm pink lapping film and continue to polish
the fiber and connector for approximately 25 strokes.The
fiber end should be flat, smooth and clean.
Step 3
This cable is now ready for use.
Any excess fiber protruding from the connector end may
be cut off; however, the trimmed fiber should extend at
least 1.5 mm (0.06 in) from the connector end.
Note:Useofthepinklappingfilmfinepolishingstepresultsin
approximately 2 dB improvement in coupling performance
of either a transmitterreceiver link or a bulkhead/splice over
a 600 grit polish alone. This fine polish is comparable to the
Avago factory polish. The fine polishing step may be omitted
where an extra 2 dB of optical power is not essential, as with
shortlinklengths. Properpolishingofthetipofthefiber/con
nector face results in a tip diameter between 2.5 mm (0.098
in.) minimum and 3.2 mm (0.126 in.) maximum..
Insert the connector fully into the polishing fixture with
the trimmed fiber protruding from the bottom of the
fixture. This plastic polishing fixture can be used to polish
two simplex connectors or simplex latching connectors
simultaneously, or one duplex connector.
Note: The four dots on the bottom of the polishing fixture
are wear indicators. Replace the polishing fixture when any
dot is no longer visible. Typically, the polishing fixture can
be used 10 times; 10 duplex connectors or 20 simplex con
nectors, two at a time.
HFBR-4594Z Polishing Kit
Place the 600 grit abrasive paper on a flat smooth surface,
pressing down on the connector, polish the fiber and the
connector using a figure eight pattern of strokes until
the connector is flush with the bottom of the polishing
fixture. Wipe the connector and fixture with a clean cloth
or tissue.
6
Ordering Guide for POF Connectors and Accessories
Plastic Optical Fiber Connectors
HFBR-4501Z
HFBR-4511Z
HFBR-4503Z
HFBR-4513Z
HFBR-4506Z
HFBR-4516Z
HFBR-4505Z
HFBR-4515Z
Gray Simplex Connector/Crimp Ring
Blue Simplex Connector/Crimp Ring
Gray Simplex Latching Connector with Crimp Ring
Blue Simplex Latching Connector with Crimp Ring
Parchment Duplex Connector with Crimp Ring
Gray Duplex Latching Connector with Crimp Ring
Gray Adapter (Bulkhead/Feedthrough)
Blue Adapter (Bulkhead/Feedthrough)
Plastic Optical Fiber Accessories
HFBR-4522Z
HFBR-4525Z
HFBR-4526Z
HFBR-4594Z
500 HFBR-0500 Products Port Plugs
1000 Simplex Crimp Rings
500 Duplex Crimp Rings
Polishing Kit (one polishing tool, two pieces 600 grit
abrasive paper, and two pieces 3 µm pink lapping film)
Plastic Fiber Crimping Tool
HFBR-4597Z
Ordering Guide for POF Cable
Cable Length Tolerances:
For Example:
The plastic cable length tolerances are: +10%/-0%.
HFBR-RUD500ZisaStandardAttenuation,Unconnectored,
Duplex, 500 meter cable.
NOTE: By convention, pre-connectored simplex POF ca-
bles have gray and blue colored connectors on the op-
posite ends of the same fiber; although oppositely col-
ored, the connectors are mechanically identical. Duplex
POF cables with duplex connectors use color- coded
markings on the duplex fiber cable to differentiate be-
tween the channel.
HFBR-RLS001ZisaStandardAttenuation,LatchingSimplex
Connectored, Simplex, 1 meter cable.
HFBR-RMD010Z is a Standard Attenuation, Standard Du-
plex Connectored, Duplex, 10 meter cable.
HFBR-RMD100Z is a Standard Attenuation, Standard Du-
plex Connectored, Duplex, 100 meter cable.
HFBR-
Z
ROHS Compliant
Cable Code
C = Commercial POF
R = Standard Attenuation POF
E = Extra Low Loss POF
Length Code
(measured from tip of connector to tip of
connector)
Maximum 500 meters (not in 1 meter
increments).
See www.avagotech.com/fiber/cables
e.g., 015 = 15 meters
Connector Code
U = Unconnectored
N = Standard Simplex Connectors
L = Latching Simplex Connectors
M = Standard Duplex Connectors
T = Latching Duplex Connectors
Channel Code
S = Simplex Cable
D = Duplex Zipcord Cable
Note: Not all possible combinations reflect available part numbers.
Please contact your local Avago representative for a list of current available cable part numbers.
7
Connector Applications
Attachment to Avago Versatile Link Fiber Optic Components
Bulkhead Feedthrough or Panel Mounting for HFBR-4501Z/4511Z Simplex Connectors
8
Versatile Link Mechanical Dimensions
Fiber Optic Cable Dimensions
Panel Mounting – Bulkhead Feedthrough
1.0 POF
(0.039)
0.230 HCS
(0.009)
HFBR-4505Z (Gray)/4515Z (Blue) Adapters
Bulkhead Feedthrough with Two HFBR-4501Z/4511Z Connectors
All dimensions in mm (inches).
All dimensions 0.25 mm unless otherwise specified.
9
Versatile Link Mechanical Dimensions, continued
HFBR-4516Z (Parchment) Duplex Latching Connector
HFBR-4506Z (Parchment) Duplex Connector
HFBR-4503Z (Gray)/4513Z (Blue) Simplex Latching Connector
HFBR-4501Z (Gray)/4511Z (Blue) Simplex Connector
All dimensions in mm (inches).
All dimensions 0.25 mm unless otherwise specified.
For product information and a complete list of distributors, please go to our website: www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2013 Avago Technologies. All rights reserved. Obsoletes AV01-0150EN
AV02-1508EN - December 5, 2013
相关型号：
HFBR-4505
Plastic Optical Fiber Cable and Accessories for Versatile Link Telecommunications switching systems
AVAGO
HFBR-4506
Plastic Optical Fiber Cable and Accessories for Versatile Link Telecommunications switching systems
AVAGO
HFBR-4511
Plastic Optical Fiber Cable and Accessories for Versatile Link Telecommunications switching systems
AVAGO
©2020 ICPDF网 联系我们和版权申明