LTC1740CG#TR [Linear]
LTC1740 - 14-Bit, 6Msps, Sampling ADC; Package: SSOP; Pins: 36; Temperature Range: 0°C to 70°C;
| 型号： | LTC1740CG#TR |
| 厂家： | 
Linear |
| 描述： | LTC1740 - 14-Bit, 6Msps, Sampling ADC; Package: SSOP; Pins: 36; Temperature Range: 0°C to 70°C 光电二极管 转换器 |
| 文件： | 总16页 (文件大小：927K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LTC1740
14-Bit, 6Msps,
Sampling ADC
U
FEATURES
DESCRIPTIO
The LTC®1740 is a 6Msps, 14-bit sampling A/D converter
that draws only 245mW from either a single 5V or dual
±5V supplies. This easy-to-use device includes a high
dynamic range sample-and-hold and a programmable
precision reference.
■
6Msps Sample Rate
■
79dB S/(N + D) and 91dB SFDR at 2.5MHz fIN
■
Single 5V Supply or ±5V Supplies
■
Integral Nonlinearity Error: <1LSB
■
Differential Nonlinearity: <0.5LSB
■
80MHz Full-Power Bandwidth Sampling
The LTC1740 has a flexible input circuit that allows differ-
entialfull-scaleinputrangesof±2.5Vand ±1.25Vwiththe
internal reference, or any full-scale input range up to
±2.5V with an external reference. The input common
mode voltage is arbitrary, though a 2.5V reference is
provided for single supply applications.
■
±2.5V and ±1.25V Bipolar Input Ranges
■
2.5V Signal Ground Available
Out-of-Range Indicator
■
■
True Differential Inputs with 75dB CMRR
■
Power Dissipation: 245mW
■
36-Pin SSOP Package (0.209 Inch Width)
DCspecificationsinclude1LSBtypicalINL, 0.5LSBtypical
DNLandnomissingcodesovertemperature. Outstanding
AC performance includes 79dB S/(N + D) and 91dB SFDR
at an input frequency of 2.5MHz.
U
APPLICATIO S
■
Telecommunications
■
Multiplexed Data Acquisition Systems
Theuniquedifferentialinputsample-and-holdcanacquire
single-ended or differential input signals up to its 80MHz
bandwidth. The 75dB common mode rejection allows
users to eliminate ground loops and common mode noise
by measuring signals differentially from the source. A
separate output logic supply allows direct connection to
3V components.
■
High Speed Data Acquisition
Spectral Analysis
Imaging Systems
■
■
, LTC and LT are registered trademarks of Linear Technology Corporation.
W
BLOCK DIAGRA
5V
5V
32
3V TO 5V
1µF
1µF
1µF
8
9
33
19
4096-Point FFT
V
V
DD
V
DD
V
DD
OV
DD
DD
+
A
IN
OF
1
+
0
36
12
f
f
= 6MHz
SMPL
= 2.5MHz, 5V
–20 5V SUPPLY
D13 (MSB)
V
1000pF
IN
S/H
PIPELINED 14-BIT ADC
IN
P-P
–A
IN
2
3
–
V
CM
–40
–60
D7
D6
18
20
1µF
DIGITAL
OUTPUT
OUTPUT
BUFFERS
DIGITAL CORRECTION
LOGIC
MODE SELECT
SENSE
4
5
–80
2.5V
REFERENCE
D0 (LSB)
BUSY
26
27
–100
–120
V
REF
1µF
CLK
2.250V
GND
35
6MHz CLK
0
1.0
1.5
2.0
2.5
3.0
0.5
FREQUENCY (MHz)
V
SS
V
SS
GND
GND
GND
GND
OGND
OGND
28
1740 TA02
1740 TA01
30
29
6
7
10
34
31
11
1µF
0V OR –5V
1740f
1
LTC1740
W W U W
W U
ABSOLUTE MAXIMUM RATINGS
PACKAGE/ORDER INFORMATION
0VDD = VDD (Notes 1, 2)
TOP VIEW
Supply Voltage (VDD)................................................. 6V
Negative Supply Voltage (VSS) ................................ –6V
Total Supply Voltage (VDD to VSS) ........................... 12V
Analog Input Voltage
(Note 3) ......................... (VSS – 0.3V) to (VDD + 0.3V)
Digital Input Voltage
(Note 3) ......................... (VSS – 0.3V) to (VDD + 0.3V)
Digital Output Voltage........ (VSS – 0.3V) to (VDD + 0.3V)
Power Dissipation.............................................. 500mW
Operating Temperature Range
LTC1740C ............................................... 0°C to 70°C
LTC1740I............................................ –40°C to 85°C
Storage Temperature Range ................. –65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
ORDER PART
NUMBER
1
2
OF
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
+A
–A
V
IN
IN
CLK
GND
LTC1740CG
LTC1740IG
3
CM
4
V
DD
SENSE
5
V
V
REF
DD
6
GND
GND
GND
7
V
SS
8
V
V
DD
SS
9
OGND
BUSY
D0
V
DD
10
11
12
13
14
15
16
17
18
GND
OGND
D13 (MSB)
D12
D1
D2
D3
D11
D4
D10
D5
D9
D6
D8
OV
DD
D7
G PACKAGE
36-LEAD PLASTIC SSOP
TJMAX = 125°C, θJA = 95°C/W
Consult LTC Marketing for parts specified with wider operating temperature
ranges.
U
CO VERTER CHARACTERISTICS The ● denotes specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. With internal 4.500V reference. Specifications are guaranteed for both
dual supply and single supply operation. (Notes 4, 5)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Bits
Resolution (No Missing Codes)
Integral Linearity Error
Differential Linearity Error
Offset Error
●
14
(Note 6)
1
±2.5
LSB
●
●
–1
0.5
±15
1.25
LSB
(Note 7)
± 60
± 80
LSB
LSB
Full-Scale Error
±30
±15
± 75
LSB
Full-Scale Tempco
I
= 0
ppm/°C
OUT(REF)
1740f
2
LTC1740
U
U
A ALOG I PUT
The ● denotes specifications which apply over the full operating temperature range, otherwise
specifications are at TA = 25°C. Specifications are guaranteed for both dual supply and single supply operation. (Note 4)
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
V
Analog Input Range
V
V
= 4.5V (SENSE = 0V)
= 2.25V (SENSE Tied to V
●
●
●
±2.50
±1.25
V
V
V
IN
REF
REF
)
REF
External V
(SENSE = 5V)
±V /1.8
REF
REF
I
Analog Input Leakage Current
Analog Input Capacitance
●
±10
µA
IN
C
Between Conversions
During Conversions
12
4
pF
pF
IN
t
t
t
Sample-and-Hold Acquisition Time
67
–900
0.6
ns
ps
ACQ
AP
Sample-and-Hold Aperture Delay Time
Sample-and-Hold Aperture Delay Time Jitter
Analog Input Common Mode Rejection Ratio
ps
jitter
RMS
CMRR
V
< (–A = +A ) < V
DD
75
dB
SS
IN
IN
U W
V
DD = OVDD = 5V, VSS = 0V, VREF = 4.5V, AIN = –0.1dBFS, AC coupled differential input.
DY A IC ACCURACY
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
S/(N + D) Signal-to-Noise Plus Distortion Ratio
1MHz Input Signal
2.5MHz Input Signal
79.1
79.0
dB
dB
THD
Total Harmonic Distortion
1MHz Input Signal, First 5 Harmonics
2.5MHz Input Signal, First 5 Harmonics
–90
–89
dB
dB
SFDR
Spurious Free Dynamic Range
1MHz Input Signal
2.5MHz Input Signal
92
91
dB
dB
Full-Power Bandwidth
Input Referred Noise
80
MHz
0.45
LSB
RMS
U U
U
I TER AL REFERE CE CHARACTERISTICS
TA = 25°C. Specifications are guaranteed for both dual supply and single supply operation. (Note 4)
PARAMETER CONDITIONS
MIN
TYP
2.500
±15
MAX
UNITS
V
V
V
V
Output Voltage
Output Tempco
Line Regulation
I
I
= 0
= 0
2.475
2.525
CM
CM
CM
OUT
OUT
ppm/°C
4.75V ≤ V ≤ 5.25V
–5.25V ≤ V ≤ –4.75V
0.6
0.03
mV/V
mV/V
DD
SS
V
V
Output Resistance
Output Voltage
0.1mA ≤
I
≤ 0.1mA
OUT
8
Ω
CM
SENSE = GND, I
SENSE = V , I
SENSE = V
= 0
= 0
4.500
2.250
V
V
V
REF
OUT
REF OUT
DD
Drive V
with
REF
External Reference
V
Output Tempco
±15
ppm/°C
REF
1740f
3
LTC1740
U
U
DIGITAL I PUTS A D DIGITAL OUTPUTS
The ● denotes specifications which apply over the full
operating temperature range, otherwise specifications are at TA = 25°C. Specifications are guaranteed for both dual supply and single
supply operation. (Note 4)
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
V
High Level Input Voltage
V
V
= 5.25V, V = 0V
●
●
2.4
2.4
V
V
IH
DD
DD
SS
= 5.25V, V = –5V
SS
V
Low Level Input Voltage
V
V
= 4.75V, V = 0V
●
●
0.8
0.8
V
V
IL
DD
DD
SS
= 4.75V, V = –5V
SS
I
Digital Input Current
V
= 0V to V
DD
●
±10
µA
IN
IN
C
V
Digital Input Capacitance
High Level Output Voltage
1.8
pF
IN
0V = 4.75V, I = –10µA
4.74
4.71
2.6
V
V
V
V
OH
DD
O
0V = 4.75V, I = –200µA
●
●
4.0
2.3
DD
O
0V = 2.7V, I = –10µA
DD
O
0V = 2.7V, I = –200µA
DD
O
V
Low Level Output Voltage
0V = 4.75V, I = 160µA
0.05
0.10
0.05
0.10
V
V
V
V
OL
DD
O
0V = 4.75V, I = 1.6mA
●
●
0.4
0.4
DD
O
0V = 2.7V, I = 160µA
DD
O
0V = 2.7V, I = 1.6mA
DD
OUT
OUT
O
I
I
Output Source Current
Output Sink Current
V
V
= 0V, 0V = 5V
50
35
mA
mA
SOURCE
SINK
DD
= V , 0V = 5V
DD
DD
W U
POWER REQUIRE E TS
The ● denotes specifications which apply over the full operating temperature range,
otherwise specifications are at TA = 25°C. Specifications are guaranteed for both dual supply and single supply operation. (Note 4)
SYMBOL PARAMETER
CONDITIONS
(Note 9)
MIN
4.75
2.7
TYP
MAX
UNITS
V
Positive Supply Voltage
Output Supply Voltage
Negative Supply Voltage
5.25
V
V
DD
OV
(Note 9)
V
DD
DD
V
Dual Supply Mode
Single Supply Mode
–5.25
–4.75
V
V
SS
0
I
I
Positive Supply Current
Negative Supply Current
Power Dissipation
●
●
●
47
60
2.6
300
mA
mA
DD
SS
2.3
245
P
mW
D
W U
TI I G CHARACTERISTICS
The ● denotes specifications which apply over the full operating temperature
range, otherwise specifications are at TA = 25°C. Specifications are guaranteed for both dual supply and single supply operation.
(Note 4)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
6
UNITS
MHz
ns
f
t
t
t
t
t
t
t
Sampling Frequency
Conversion Time
●
●
●
●
●
0.05
SAMPLE
100
67
135
CONV
Acquisition Time
(Note 9)
(Note 9)
(Note 9)
31
20
20
ns
ACQ
H
CLK High Time
83.3
83.3
–900
3.5
ns
CLK Low Time
ns
L
Aperature Delay of Sample-and-Hold
CLK↑ to BUSY↓
ps
AP
1
ns
BUSY↑ to Outputs Valid
Data Latency
1.5
ns
2
3
Cycles
1740f
4
LTC1740
W U
TI I G CHARACTERISTICS
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: All voltage values are with respect to ground with GND and OGND
Note 6: Integral nonlinearity is defined as the deviation of a code from a
straight line passing through the actual endpoints of the transfer curve.
The deviation is measured from the center of the quantization band.
wired together (unless otherwise noted).
Note 3: When these pin voltages are taken below V or above V , they
Note 7: Bipolar offset is the offset voltage measured from –0.5LSB
when the output code flickers between 00 0000 0000 0000 and
11 1111 1111 1111.
Note 8: Guaranteed by design, not subject to test.
Note 9: Recommended operating conditions.
SS
DD
will be clamped by internal diodes. This product can handle input currents
greater than 100mA below V or above V without latchup.
SS
DD
Note 4: V = 5V, V = –5V or 0V, f
= 6MHz, t = t = 5ns unless
r f
DD
SS
SAMPLE
otherwise specified.
Note 5: Linearity, offset and full-scale specifications apply for a
single-ended +A input with –A tied to V for single supply and 0V for
IN
IN
CM
dual supply.
U W
TYPICAL PERFOR A CE CHARACTERISTICS
S/(N + D) vs Input Frequency
and Amplitude
Typical INL at 6Msps
Typical DNL at 6Msps
80
75
70
65
60
55
50
1.0
0.8
2.0
1.5
V
IN
= 0dBFS
0.6
V
IN
= –6dBFS
1.0
0.4
0.5
0.2
0
0
–0.2
–0.4
–0.6
–0.8
–1.0
V
IN
= –20dBFS
–0.5
–1.0
–1.5
–2.0
DUAL SUPPLIES
5V INPUT RANGE
DIFFERENTIAL INPUT
6Msps
0.1
1
10
100
0
4096
8192
12288
16384
8192
0
4096
12288
16384
INPUT FREQUENCY (MHz)
CODE
CODE
1740 G03
1740 G02
1740 G01
S/(N + D) vs Input Frequency
and Amplitude
SFDR and THD
SFDR and THD
vs Input Frequency
vs Input Frequency
80
75
70
65
60
55
50
95
90
85
80
75
70
65
60
55
95
90
85
80
75
70
65
60
55
V
IN
= 0dBFS
SFDR
SFDR
V
IN
= –6dBFS
–THD
–THD
V
IN
= –20dBFS
DUAL SUPPLIES
5V INPUT RANGE
SINGLE SUPPLY
5V INPUT RANGE
SINGLE SUPPLY
5V INPUT RANGE
DIFFERENTIAL INPUT
6Msps
A
IN
= 0dBFS
A
IN
= 0dBFS
DIFFERENTIAL INPUT
6Msps
DIFFERENTIAL INPUT
6Msps
50
50
0.1
1
10
100
0.1
1
100
0.1
1
100
10
10
INPUT FREQUENCY (MHz)
INPUT FREQUENCY (MHz)
INPUT FREQUENCY (MHz)
1740 G04
1740 G05
1740 G06
1740f
5
LTC1740
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Spurious-Free Dynamic Range
vs Input Amplitude
Spurious-Free Dynamic Range
vs Input Amplitude
S/(N + D) and SFDR
vs Sample Frequency
100
90
100
90
95
90
85
80
75
70
65
60
55
50
SFDR
dBFS
dBFS
S/(N + D)
80
70
80
70
dBc
dBc
60
50
0
60
50
0
DUAL SUPPLIES
5V INPUT RANGE
DIFFERENTIAL INPUT
6Msps
SINGLE SUPPLY
5V INPUT RANGE
DIFFERENTIAL INPUT
6Msps
DUAL SUPPLIES
5V INPUT RANGE
DIFFERENTIAL INPUT
6Msps
–50
–40
–30
–20
–10
0
–50
–40
–30
–20
–10
0
3
0
1
2
4
5
6
7
8
INPUT AMPLITUDE (dBFS)
INPUT AMPLITUDE (dBFS)
SAMPLE FREQUENCY (MHz)
1740 G07
1740 G08
1740 G09
S/(N + D) and SFDR
vs Sample Frequency
Nonaveraged 4096 Point FFT
Nonaveraged 4096 Point FFT
0
–20
0
–20
95
90
85
80
75
70
65
60
55
50
DUAL SUPPLIES
6Msps
SFDR
f
= 2.5MHz, 5V
IN
P-P
DIFFERENTIAL INPUT
–40
–40
S/(N + D)
–60
–60
–80
–80
–100
–120
–140
–100
–120
–140
SINGLE SUPPLY
5V INPUT RANGE
DIFFERENTIAL INPUT
6Msps
3
2
3
2
3
0
1
2
4
5
6
7
8
0
0.5
1
1.5
2.5
0
0.5
1
1.5
2.5
SAMPLE FREQUENCY (MHz)
FREQUENCY (MHz)
FREQUENCY (MHz)
1740 G10
1740 G11
1740 G12
IDD vs Clock Frequency
ISS vs Clock Frequency
2.5
2.0
1.5
1.0
49
47
45
43
41
39
37
35
V
REF
= 4.5V
V
REF
= 2.25V
0.5
0
0
2
3
4
5
6
1
4
6
0
1
2
3
5
CLOCK FREQUENCY (MHz)
CLOCK FREQUENCY (MHz)
1740 G14
1740 G13
1740f
6
LTC1740
U
U
U
PIN FUNCTIONS
+AIN (Pin 1): Positive Analog Input.
OVDD (Pin 19): Positive Supply for the Output Logic. Can
be 2.7V to 5.25V. Bypass to GND with a 1µF to 10µF
ceramic capacitor.
–AIN (Pin 2): Negative Analog Input.
V
CM (Pin 3): 2.5V Reference Output. Optional input com-
BUSY (Pin 27): BUSY is low when a conversion is in
progress. When a conversion is finished and the ADC is
acquiring the input signal, BUSY is high. Either the falling
edge of BUSY or the rising edge of CLK can be used to
latch the output data.
mon mode for single supply operation. Bypass to GND
with a 1µF to 10µF ceramic capacitor.
SENSE (Pin 4): Reference Programming Pin. Ground
selects VREF = 4.5V. Short to VREF for VREF = 2.25V.
Connect SENSE to VDD to drive VREF with an external
reference. Connect SENSE directly to VDD, VREF or GND.
Do not drive SENSE with a logic signal.
V
SS (Pins 29, 30): Negative Supply. Can be –5V or 0V. If
VSS is not shorted to GND, bypass to GND with a 1µF
ceramic capacitor.
VREF (Pin 5): DAC Reference. Bypass to GND with a 1µF to
10µF ceramic capacitor.
VDD (Pins 32, 33): Analog 5V Supply. Bypass to GND with
a 1µF to 10µF ceramic capacitor (do not share a capacitor
with Pins 8, 9).
GND (Pins 6, 7, 10, 31, 34): Analog Power Ground.
VDD (Pins 8, 9): Analog 5V Supply. Bypass to GND with a
1µF to 10µF ceramic capacitor. (Do not share a capacitor
with Pins 32 and 33.)
CLK (Pin 35): Conversion Start Signal. This active high
signal starts a conversion on its rising edge.
OF (Pin 36): Overflow Output. This signal is high when the
digitaloutputis01111111111111or10000000000000.
OGND (Pins 11, 28): Output Logic Ground. Connect to
GND.
D13 to D0 (Pins 12 to 18, 20 to 26): Data Outputs. The
output format is two’s complement.
1740f
7
LTC1740
U
U
W
FUNCTIONAL BLOCK DIAGRA
5V
3V TO 5V
V
DD
OV
DD
+
A
IN
S/H
PIPELINED 14-BIT ADC
OF
–A
IN
D13 (MSB)
V
CM
OUTPUT
BUFFERS
DIGITAL CORRECTION
LOGIC
MODE SELECT
D0 (LSB)
BUSY
SENSE
2.5V
REFERENCE
V
REF
CLK
1740 FBD
V
GND
GND
OGND
SS
0V OR –5V
W U
W
TI I G DIAGRA
N + 1
N
ANALOG
INPUT
N + 2
N + 3
t
CLOCK
t
H
t
L
CLK
t
CONV
t
ACQ
DATA
OUTPUT
N-3
N-2
N-1
N
t
2
BUSY
1740 TD
t
1
1740f
8
LTC1740
W U U
U
APPLICATIO S I FOR ATIO
Conversion Details
5Vdigitalsystems.Forsinglesupplyoperation,VSS should
beconnectedtoanalogground. Fordualsupplyoperation,
SS should be connected to –5V. All VDD pins should be
connectedtoaclean5Vanalogsupply.(Don’tconnectVDD
to a noisy system digital supply.)
The LTC1740 is a high performance 14-bit A/D converter
that operates up to 6Msps. It is a complete solution with
an on-chip sample-and-hold, a 14-bit pipelined CMOS
ADC and a low drift programmable reference. The digital
output is parallel, with a 14-bit two’s complement format
and an out-of-range (overflow) bit.
V
Analog Input Range
The LTC1740 has a flexible analog input with a wide
selection of input ranges. The input range is always
differential and is set by the voltage at the VREF pin
(Figure 1). The input range of the A/D core is fixed at
±VREF/1.8. The reference voltage, VREF, is either set by the
on-chip voltage reference or directly driven by an external
voltage.
The rising edge of the CLK begins the conversion. The
differential analog inputs are simultaneously sampled and
passed on to the pipelined A/D. After two more conversion
starts (plus a 100ns conversion time) the digital outputs
areupdatedwiththeconversionresultandwillbereadyfor
capture on the third rising clock edge. Thus even though
anewconversionisbeguneverytimeCLKgoeshigh, each
result takes three clock cycles to reach the output.
Internal Reference
The analog signals that are passed from stage to stage in
the pipelined A/D are stored on capacitors. The signals on
these capacitors will be lost if the delay between conver-
sions is too long. For accurate conversion results, the part
should be clocked faster than 50kHz.
Figure 2 shows a simplified schematic of the LTC1740
reference circuitry. An on-chip temperature compensated
bandgap reference (VCM) is factory trimmed to 2.500V.
The voltage at the VREF pin sets the input span of the ADC
to ±VREF/1.8. An internal voltage divider converts VCM to
2.250V, which is connected to a reference amplifier. The
reference programming pin, SENSE, controls how the
InsomepipelinedA/Dconvertersifthereisnoclockpresent,
dynamic logic on the chip will droop and the power con-
sumption sharply increases. The LTC1740 doesn’t have
this problem. If the part is not clocked for 1ms, an internal
timer will refresh the dynamic logic. Thus the clock can be
turned off for long periods of time to save power.
TO
ADC
V
REF
1µF
+
–
1k
Power Supplies
R1
5k
The LTC1740 will operate from either a single 5V or dual
±5V supply, making it easy to interface the analog input to
single or dual supply systems. The digital output drivers
have their own power supply pin (OVDD) which can be set
from 3V to 5V, allowing direct connection to either 3V or
SENSE
R2
5k
LOGIC
2.5V
REFERENCE
+A
IN
+
±V
1.8
REF
ADC
CORE
V
2.250V
IN
–A
IN
V
CM
–
1µF
V
REF
1740 F01
1740 F02
Figure 1. Analog Input Circuit
Figure 2. Reference Circuit
1740f
9
LTC1740
W U U
U
APPLICATIO S I FOR ATIO
reference amplifier drives the VREF pin. If SENSE is tied to
ground, the reference amplifier feedback is connected to
the R1/R2 voltage divider, thus making VREF = 4.500V. If
SENSE is tied to VREF, the reference amplifier feedback is
connectedtoSENSEthusmakingVREF =2.250V. IfSENSE
istiedtoVDD, thereferenceamplifierisdisconnectedfrom
VREF and VREF can be driven by an external voltage. With
additional resistors between VREF and SENSE, and SENSE
and GND, VREF can be set to any voltage between 2.250V
and 4.5V.
Both the VCM and VREF pins must be bypassed with
capacitors to ground. For best performance, 1µF or larger
ceramic capacitors are recommended. For the case of
external circuitry driving VREF, a smaller capacitor can be
used at VREF so the input range can be changed quickly.
In this case, a 0.2µF or larger ceramic capacitor is
acceptable.
The VCM pin is a low output impedance 2.5V reference that
can be used by external circuitry. For single 5V supply
applications it is convenient to connect AIN– directly to the
An external reference or a DAC can be used to drive VREF
over a 0V to 5V range (Figures 3a and 3b). The input
impedance of the VREF pin is 1kΩ, so a buffer may be
required for high accuracy. Driving VREF with a DAC is
useful in applications where the peak input signal ampli-
tude may vary. The input span of the ADC can then be
adjusted to match the peak input signal, maximizing the
signal-to-noise ratio.
VCM pin.
Driving the Analog Inputs
The differential inputs of the LTC1740 are easy to drive.
The inputs may be driven differentially or single-ended
(i. e., the AIN– input is held at a fixed value). The AIN– and
AIN+ inputs are simultaneously sampled and any common
mode signal is reduced by the high common mode rejec-
tion of the sample-and-hold circuit. Any common mode
input value is acceptable as long as the input pins stay
between VDD and VSS. During conversion the analog
inputs are high impedance. At the end of conversion the
inputs draw a small current spike while charging the
sample-and-hold.
5V
V
IN
V
V
REF
OUT
1µF
1µF
LT1019A-2.5
LTC1740
SENSE
5V
For superior dynamic performance in dual supply mode,
the LTC1740 should be operated with the analog inputs
centered at ground, and in single supply mode the inputs
should be centered at 2.5V. For the best dynamic perfor-
mance, the analog inputs can be driven differentially via a
transformer or differential amplifier.
V
CM
1740 F03a
Figure 3a. Using the LT1019-2.5 as an
External Reference; Input Range = ±1.39V
DC Coupling the Input
LTC1740
2.250V
+
–
V
In many applications the analog input signal can be
directly coupled to the LTC1740 inputs. If the input signal
is centered around ground, such as when dual supply op
amps are used, simply connect AIN– to ground and con-
nect VSS to –5V (Figure 4). In a single power supply
system with the input signal centered around 2.5V, con-
nect AIN– to VCM and VSS to ground (Figure 5). If the input
signal is not centered around ground or 2.5V, the voltage
for AIN– must be generated externally by a resistor divider
or a voltage reference (Figure 6).
REF
1µF
5k
SENSE
5k
V
CM
1µF
LTC1450
1740 F03b
Figure 3b. Driving VREF with a DAC
1740f
10
LTC1740
W U U
APPLICATIO S I FOR ATIO
U
5V
5V
C
+A
–A
+A
IN
0V
V
0V
V
IN
IN
IN
LTC1740
LTC1740
–A
IN
IN
C
R
R
V
V
CM
CM
V
SS
V
SS
1µF
1µF
1405 F04
1740 F07
–5V
Figure 4. DC Coupling a Ground Centered Signal
(Dual Supply System)
Figure 7. AC Coupling to the LTC1740. Note That the Input Signal
Can Almost Always Be Directly Coupled with Better Performance
5V
5V
MINI CIRCUITS
15Ω
T1-1T
+A
–A
+A
IN
2.5V
V
IN
IN
V
1000pF
LTC1740
LTC1740
IN
IN
–A
IN
15Ω
V
CM
V
CM
V
SS
V
SS
1µF
1µF
1740 F05
1740 F08a
Figure 5. DC Coupling a Signal Centered Around
2.5V (Single Supply System)
Figure 8a. Single Supply Transformer Coupled Input
5V
MINI CIRCUITS
5V
15Ω
T1-1T
+A
–A
IN
LTC1740
2.500V
+A
–A
V
IN
IN
V
1000pF
IN
0V
5V
LTC1740
IN
1.25V
15Ω
IN
V
REF
V
CM
V
SENSE
SS
1µF
1740 F08b
V
SS
1µF
1740 F06
–5V
Figure 8b. Dual Supply Transformer Coupled Input
Figure 6. DC Coupling a 0V to 2.5V Signal
Differential Operation
AC Coupling the Input
The THD and SFDR performance of the LTC1740 can be
improved by using a center tap RF transformer to drive the
inputs differentially. Though the signal can no longer be
DC coupled, the improvement in dynamic performance
makes this an attractive solution for some applications.
Typical connections for single and dual supply systems
are shown in Figures 8a and 8b. Good choices for trans-
formers are the Mini Circuits T1-1T (1:1 turns ratio) and
T4-6T (1:4 turns ratio). For best results the transformer
should be located close to the LTC1740 on the printed
The analog inputs to the LTC1740 can also be AC coupled
through a capacitor, though in most cases it is simpler to
directly couple the input to the ADC. Figure 7 shows an
example where the input signal is centered around ground
and the ADC operates from a single 5V supply. Note that
the performance would improve if the ADC was operated
from a dual supply and the input was directly coupled (as
in Figure 4). With AC coupling the DC resistance to ground
should be roughly matched for AIN+ and AIN– to maintain
offset accuracy.
circuit board.
1740f
11
LTC1740
W U U
U
APPLICATIO S I FOR ATIO
Choosing an Input Amplifier
30Ω
+A
–A
V
IN
IN
Choosing an input amplifier is easy if a few requirements
are taken into consideration. First, to limit the magnitude
of the voltage spike seen by the amplifier from charging
the sampling capacitor, choose an amplifier that has a low
output impedance (<100Ω) at the closed-loop bandwidth
frequency. For example, if an amplifier is used in a gain
of 1 and has a unity-gain bandwidth of 50MHz, then the
output impedance at 50MHz must be less than 100Ω. The
second requirement is that the closed-loop bandwidth
must be greater than 50MHz to ensure adequate small-
signal settling for full throughput rate. If slower op amps
areused, moresettlingtimecanbeprovidedbyincreasing
the time between conversions.
1000pF
LTC1740
IN
1740 F09
Figure 9. RC Input Filter
usedsincethesecomponentscanadddistortion.NPOand
silver mica type dielectric capacitors have excellent linear-
ity. Carbon surface mount resistors can generate distor-
tion from self-heating and from damage that may occur
during soldering. Metal film surface mount resistors are
much less susceptible to both problems.
Digital Outputs and Overflow Bit (OF)
The best choice for an op amp to drive the LTC1740 will
depend on the application. Generally applications fall into
two categories: AC applications where dynamic specifica-
tionsaremostcriticalandtimedomainapplicationswhere
DC accuracy and settling time are most critical.
Figure 10 shows the ideal input/output characteristics for
the LTC1740. The output data is two’s complement binary
for all input ranges and for both single and dual supply
operation. One LSB = VREF/(0.9 • 16384). To create a
straightbinaryoutput, inverttheMSB(D13). Theoverflow
bit (OF) indicates when the analog input is outside the
input range of the converter. OF is high when the output
code is 10 0000 0000 0000 or 01 1111 1111 1111.
Input Filtering
The noise and the distortion of the input amplifier and
other circuitry must be considered since they will add to
the LTC1740 noise and distortion. The small-signal band-
width of the sample-and-hold circuit is 80MHz. Any noise
ordistortionproductsthatarepresentattheanaloginputs
will be summed over this entire bandwidth. Noisy input
circuitry should be filtered prior to the analog inputs to
minimize noise. A simple 1-pole RC filter is sufficient for
many applications.
1
0
OVERFLOW
BIT
011…111
011…110
011…101
For example, Figure 9 shows a 1000pF capacitor from
+AIN to –AIN and a 30Ω source resistor to limit the input
bandwidth to 5.3MHz. The 1000pF capacitor also acts as
a charge reservoir for the input sample-and-hold and iso-
latestheamplifierdrivingVIN fromtheADC’ssmallcurrent
glitch. In undersampling applications, an input capacitor
this large may prohibitively limit the input bandwidth.
If this is the case, use as large an input capacitance as
possible. High quality capacitors and resistors should be
100…010
100…001
100…000
–(FS – 1LSB)
FS – 1LSB
INPUT VOLTAGE (V)
1740 F10
Figure 10. LTC1740 Transfer Characteristics
1740f
12
LTC1740
W U U
U
APPLICATIO S I FOR ATIO
Full-Scale and Offset Adjustment
Timing
In applications where absolute accuracy is important,
offset and full-scale errors can be adjusted to zero. Offset
error should be adjusted before full-scale error. Figure 11
shows a method for error adjustment for a dual supply,
5.00V input range application. For zero offset error apply
–0.15mV (i. e., –0.5LSB) at +AIN and adjust R1 until the
output code flickers between 00 0000 0000 0000 and 11
1111 1111 1111. For full-scale adjustment, apply an input
voltageof2.49954V(FS–1.5LSBs)at+AIN andadjustR2
untiltheoutputcodeflickersbetween01111111111110
and 01 1111 1111 1111.
The conversion start is controlled by the rising edge of the
CLK pin. Once a conversion is started it cannot be stopped
or restarted until the conversion cycle is complete. Output
data is updated at the end of conversion, or about 100ns
after a conversion is begun. There is an additional two
cycle pipeline delay, so the data for a given conversion is
output two full clock cycles plus 100ns after the convert
start. Thus output data can be latched on the third CLK
rising edge after the rising edge that samples the input.
Clock Input
The LTC1740 only uses the rising edge of the CLK pin for
internal timing, and CLK doesn’t necessarily need to have
a 50% duty cycle. For optimal AC performance the rise
time of the CLK should be less than 5ns. If the available
clock has a rise time slower than 5ns, it can be locally sped
up with a logic gate. The clock can be driven with 5V
CMOS, 3V CMOS or TTL logic levels.
Digital Output Drivers
The LTC1740 output drivers can interface to logic operat-
ing from 3V to 5V by setting OVDD to the logic power
supply. OVDD requires a 1µF decoupling capacitor. To
prevent digital noise from affecting performance, the load
capacitance on the digital outputs should be minimized. If
large capacitive loads are required, (>30pF) external buff-
ers or 100Ω resistors in series with the digital outputs are
suggested.
5V
+A
IN
V
IN
5V
24k
R1
50k
–A
IN
100Ω
LTC1740
–5V
V
REF
1µF
10k
R2
1k
SENSE
V
SS
1740 F11
10k
–5V
Figure 11. Offset and Full-Scale Adjust Circuit
1740f
13
LTC1740
W U U
U
APPLICATIO S I FOR ATIO
As with all fast ADCs, the noise performance of the
LTC1740issensitivetoclockjitterwhenhighspeedinputs
are present. The SNR performance of an ADC when the
performance is limited by jitter is given by:
should be connected to the analog ground plane at only
one point, near the OGND pin (Pin 28).
The analog ground plane should be as close to the ADC as
possible.Careshouldbetakentoavoidmakingholesinthe
analog ground plane under and around the part. To ac-
complish this, we recommend placing vias for power and
signal traces outside the area containing the part and the
decoupling capacitors (Figure 13).
SNR = –20log (2π fINtJ)dB
where fIN is the frequency of an input sine wave and tJ is
the root-mean-square jitter due to the clock, the analog
input and the A/D aperture jitter. To minimize clock jitter,
use a clean clock source such as a crystal oscillator, treat
the clock signals as sensitive analog traces and use
dedicated packages with good supply bypassing for any
clock drivers.
Supply Bypassing
High quality, low series resistance ceramic 1µF capacitors
should be used at the VDD pins, VCM and VREF. If VSS is
connected to –5V it should also be bypassed to ground
with1µF. InsinglesupplyoperationVSS shouldbeshorted
to the ground plane as close to the part as possible. OVDD
requires a 1µF decoupling capacitor to ground. Surface
mount capacitors such as the AVX 0805ZC105KAT pro-
videexcellentbypassinginasmallboardspace.Thetraces
connecting the pins and the bypass capacitors must be
kept short and should be made as wide as possible.
Board Layout
To obtain the best performance from the LTC1740, a
printed circuit board with a ground plane is required.
Layout for the printed circuit board should ensure that
digital and analog signal lines are separated as much as
possible. In particular, care should be taken not to run any
digital track alongside an analog signal track.
An analog ground plane separate from the logic system
ground should be placed under and around the ADC.
Pins 6, 7, 10, 31, 34 (GND), Pins 11, 28 (OGND) and all
other analog grounds should be connected to this ground
plane. In single supply mode, Pins 29, 30 (VSS) should
also be connected to this ground plane. All bypass capaci-
tors for the LTC1740 should also be connected to this
ground plane (Figure 12). The digital system ground
BYPASS
LTC1740
CAPACITOR
PLACE NON-GROUND
VIAS AWAY FROM
GROUND PLANE AND
BYPASS CAPACITORS
ANALOG
GROUND
PLANE
AVOID BREAKING GROUND PLANE
IN THIS AREA
1740 F13
Figure 13. Cross Section of the LTC1740 Printed Circuit Board
1
DIGITAL
SYSTEM
LTC1740
+A
IN
1000pF
V
V
GND GND
V
V
GND OGND OV
V
V
GND
V
V
GND OGND
–A
IN
ANALOG
INPUT
CIRCUITRY
CM
REF
5
DD DD
DD
19
SS SS
DD DD
2
+
3
6
7
8
9
10
11
29 30 31 32 33 34
28
–
1µF
1µF
1µF
1µF
1µF 1µF
ANALOG GROUND PLANE
1740 F12
Figure 12. Power Supply Grounding
1740f
14
LTC1740
U
PACKAGE DESCRIPTION
G Package
36-Lead Plastic SSOP (5.3mm)
(Reference LTC DWG # 05-08-1640)
12.50 – 13.10*
(.492 – .516)
1.25 ±0.12
36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19
7.8 – 8.2
5.3 – 5.7
7.40 – 8.20
(.291 – .323)
0.42 ±0.03
0.65 BSC
5
7
8
RECOMMENDED SOLDER PAD LAYOUT
1
2
3
4
6
9 10 11 12 13 14 15 16 17 18
5.00 – 5.60**
(.197 – .221)
2.0
(.079)
0° – 8°
0.65
(.0256)
BSC
0.09 – 0.25
(.0035 – .010)
0.55 – 0.95
(.022 – .037)
0.05
0.22 – 0.38
(.009 – .015)
(.002)
NOTE:
G36 SSOP 0802
1. CONTROLLING DIMENSION: MILLIMETERS
MILLIMETERS
2. DIMENSIONS ARE IN
(INCHES)
3. DRAWING NOT TO SCALE
*DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED .152mm (.006") PER SIDE
**DIMENSIONS DO NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED .254mm (.010") PER SIDE
1740f
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-
tation that the interconnection of its circuits as described herein will notinfringe onexisting patent rights.
15
LTC1740
RELATED PARTS
PART NUMBER
LTC1405
LTC1406
LTC1411
LTC1412
LTC1414
LTC1420
LT1461
DESCRIPTION
COMMENTS
12-Bit, 5Msps Sampling ADC with Parallel Output
8-Bit, 20Msps ADC
Pin Compatible with the LTC1420
Undersampling Capability up to 70MHz
5V, No Pipeline Delay, 80dB SINAD
±5V, No Pipeline Delay, 72dB SINAD
±5V, 81dB SINAD and 95dB SFDR
71dB SINAD and 83dB SFDR at Nyquist
0.04% Max Initial Accuracy, 3ppm/°C Drift
Pin Compatible with the LTC1668, LTC1667
Pin Compatible with the LTC1668, LTC1666
16-Bit, No Missing Codes, 90dB SINAD, –100dB THD
Pin Compatible with the LTC1748
Pin Compatible with the LTC1748
Pin Compatible with the LTC1748
Pin Compatible with the LTC1748
Pin Compatible with the LTC1748
Pin Compatible with the LTC1748
Pin Compatible with the LTC1748
76.3dB SNR and 90dB SFDR
14-Bit, 2.5Msps ADC
12-Bit, 3Msps, Sampling ADC
14-Bit, 2.2Msps ADC
12-Bit, 10Msps ADC
Micropower Precision Series Reference
12-Bit, 50Msps DAC
LTC1666
LTC1667
LTC1668
LTC1741
LTC1742
LTC1743
LTC1744
LTC1745
LTC1746
LTC1747
LTC1748
LT1807
14-Bit, 50Msps DAC
16-Bit, 50Msps DAC
12-Bit, 65Msps ADC
14-Bit, 65Msps ADC
12-Bit, 50Msps ADC
14-Bit, 50Msps ADC
12-Bit, 25Msps ADC
14-Bit, 25Msps ADC
12-Bit, 80Msps ADC
14-Bit, 80Msps ADC
325MHz, Low Distortion Dual Op Amp
Rail-to-Rail Input and Output
1740f
LT/TP 0603 1K • PRINTED IN USA
16 LinearTechnology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
●
●
LINEAR TECHNOLOGY CORPORATION 2003
(408) 432-1900 FAX: (408) 434-0507 www.linear.com
相关型号：
LTC1740CG#TRPBF
LTC1740 - 14-Bit, 6Msps, Sampling ADC; Package: SSOP; Pins: 36; Temperature Range: 0°C to 70°C
Linear
LTC1740IG#PBF
LTC1740 - 14-Bit, 6Msps, Sampling ADC; Package: SSOP; Pins: 36; Temperature Range: -40°C to 85°C
Linear
LTC1740IG#TRPBF
LTC1740 - 14-Bit, 6Msps, Sampling ADC; Package: SSOP; Pins: 36; Temperature Range: -40°C to 85°C
Linear
LTC1741IFW#PBF
LTC1741 - 12-Bit, 65Msps Low Noise ADC; Package: TSSOP; Pins: 48; Temperature Range: -40°C to 85°C
Linear
LTC1742IFW#PBF
LTC1742 - 14-Bit, 65Msps Low Noise ADC; Package: TSSOP; Pins: 48; Temperature Range: -40°C to 85°C
Linear
©2020 ICPDF网 联系我们和版权申明