DS1680FP-5+ [MAXIM]
Microprocessor Circuit, CMOS, PQFP44, 10 X 10 MM, 2 MM HEIGHT, ROHS COMPLIANT, MQFP-44;
| 型号： | DS1680FP-5+ |
| 厂家： | 
MAXIM INTEGRATED PRODUCTS |
| 描述： | Microprocessor Circuit, CMOS, PQFP44, 10 X 10 MM, 2 MM HEIGHT, ROHS COMPLIANT, MQFP-44 外围集成电路 |
| 文件： | 总23页 (文件大小：411K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
DS1680
Portable System Controller with
Touch-Screen Control
www.maxim-ic.com
DESCRIPTION
FEATURES
The DS1680 incorporates many functions
necessary for low-power portable products,
providing a real-time clock (RTC), NV RAM
controller, microprocessor monitor, power-fail
warning, 10-bit analog-to-digital converter (ADC),
and a touch-screen controller in one chip.
CꢀReal-Time Clock
Counts Seconds, Minutes, Hours, Date, Month,
Day of the Week, and Year with Leap-Year
Compensation Valid Up to 2100
Power Control Circuitry Supports System
Power-On from Day/Time Alarm
CꢀMicroprocessor Monitor
Halts Microprocessor During Power-Fail
Automatically Restarts Microprocessor after
Power Failure
The RTC provides seconds, minutes, hours, day,
date, month, and year information with leap-year
compensation as well as an alarm interrupt. This
interrupt works when the DS1680 is powered by
the system power supply or when in battery-
backup operation, so the alarm can be used to
wake up a system that is powered down.
Monitors Pushbutton for External Override
Halts and Resets an Out-of-Control
Microprocessor
CꢀNV RAM Control
Automatic Battery Backup and Write
Protection to External SRAM
Cꢀ1.25V Threshold Detector for Power-Fail
Warning
Automatic backup and write protection of an
external SRAM is provided through the VCCO and
CEO pins. The backup energy source used to
power the RTC is also used to retain RAM data in
the absence of VCC through the VCCO pin. CEO, the
chip-enable output to SRAM, is controlled during
power transients to prevent data corruption.
Cꢀ10-Bit ADC
Monotonic with No Missing Codes
Cꢀ4-Wire Analog Resistive Touch-Screen
Interface
ORDERING INFORMATION
PIN CONFIGURATION
VOLTAGE PIN-
TOP
PART
(V)
3.3
3.3
5
PACKAGE MARK†
TOP VIEW
DS1680FP-3
DS1680FP-3+
DS1680FP-5
DS1680FP-5+
44 MQFP
44 MQFP
44 MQFP
44 MQFP
1680FP-3
1680FP-3
1680FP-5
1680FP-5
34
33
44
1
VBAT
X1
PFI
5
GND
D7
D6
X2
AVG
* All devices are specified over the 0°C to +70°C operating range.
† A “‘+” anywhere on the top mark denotes a lead-free device.
+ Denotes a lead-free/RoHS-compliant device.
DS1680
BHE
D5
COEN
D4
D3
D2
D1
OUT_SELECT
CONVERT
PD_RESET
PEN_SELECT
ANSELIN
D0
NEW_DATA
11
12
23
22
MQFP
(10mm x 10mm x 2mm)
1 of 23
REV: 080905
DS1680
DETAILED DESCRIPTION
The DS1680’s microprocessor-monitor circuitry provides three basic functions. First, a precision
temperature-compensated reference and comparator circuit monitors the status of VCC. When an out-of-
tolerance condition occurs, an internal power-fail signal is generated that forces RST to the active state.
When VCC returns to an in-tolerance condition, the RST signal is kept in the active state for tRPU to allow
the power supply and processor to stabilize. The DS1680 debounces a pushbutton input and guarantees an
active RST pulse width of tRST. The third function is a watchdog timer. The DS1680’s internal timer
forces the RST signal to the active state if the strobe input is not driven low prior to watchdog time-out.
The DS1680 also provides a touch-screen controller along with a 10-bit successive approximation ADC.
The ADC is monotonic (no missing codes) and has an internal analog filter to reduce high frequency
noise.
DS1680 BLOCK DIAGRAM Figure 1
D0-D7
COEN
PEN_SELECT
OUT_SELECT
INT
OUTPUT
MUX
X1
RTC
X2
BHE
CLOCK
OSC
CLOCK
GEN
OSCIN
SCLK
CS
I/O
SERIAL
INTERFACE
AIN0
AIN1
INPUT
10-BIT
ADC
MUX
ST
WATCHDOG
RST
NEW_DATA
ANSELIN
CONVERT
CONTROL
VCC
CONVERT
VBAT
TOUCH
PEN_OFF
POWER SWITCH,
WRITE PROTECT,
NV CONTROL,
AND
VCCO
CEI
DETECT
POWER
POWER FAIL
WARNING
CEO
CONTROL
PD_RST
PFI
X+
X-
PANEL
DRIVE
PFO
Y+
Y-
2 of 23
DS1680
PIN DESCRIPTION
PIN
NAME
FUNCTION
1
VBAT
Battery Input for Standard 3V Lithium Cell or Other Energy Source
Connections for Standard 32.768kHz Quartz Crystal. For greatest accuracy, the
DS1680 must be used with a crystal that has a specified load capacitance of 6pF.
There is no need for external capacitors or resistors. Note: X1 and X2 are very high-
impedance nodes. It is recommended that they and the crystal be guard-ringed with
ground and that high-frequency signals be kept away from the crystal area. For more
information about crystal selection and crystal layout considerations, refer to
Application Note 58: Crystal Considerations with Dallas Real-Time Clocks. The
DS1680 does not function without a crystal.
2, 3
X1, X2
Data Average Select. Logic 1 selects data average mode; logic 0 selects raw data
mode.
4
5
6
AVG
BHE
Bus-High Enable Input. Drive to logic 1 to select high byte (data bits 2–9). Drive to
logic 0 to select low byte (data bits 0–1). The lower 6 bits will all be zeros when
asserted low.
Active-Low Chip Output Enable. Must be asserted low to enable the ADC data to be
read on D0–D7.
COEN
Output Select Input. Assert to logic 0 to select AIN0 or X- data. Assert to logic 1 to
select AIN1 or Y- data. Use with PEN_SELECT input.
7
8
9
OUT_SELECT
CONVERT
Assert to logic 1 to request sample from AIN0 or AIN1. Use with ANSELIN input.
Power-Down/Reset Input. Assert logic 1 for O 10ns to reset. Hold at logic 1 for
PD_RESET
power-down mode of the analog circuitry.
Pen Select Input. Assert to logic 1 to select X- or Y- data output. Assert to logic 0 to
select AIN0 or AIN1 data output. Use with OUT_SELECT input.
Analog Select Input. Assert to logic 0 to select AIN0. Assert to logic 1 to select AIN1.
Use with CONVERT input.
10
11
PEN_SELECT
ANSELIN
12, 16
13
AVS, AVD
VREF
ADC Supply and Ground
Voltage Reference
14, 15
17, 18
19, 20
21
AIN0, AIN1
Y+, Y-
Analog Inputs
Resistive Tablet Y Plane Driver. Connect to Y-terminal of resistive tablet.
Resistive Tablet X Plane Driver. Connect to X-terminal of resistive tablet.
Pen Detection Output. Indicates pen not detected. Logic 1 if pen is not detected.
Oscillator Input. Input for the ADC clock.
X+, X-
PEN_OFF
OSCIN
22
Active-Low New Data Indicator. A logic 0 pulse indicates that new data packet is
available on D0–D7.
23
24–31
32
NEW_DATA
D0–D7
Data Bus. Data output from ADC.
Digital Ground. DC power to the RTC, watchdog, X and Y drivers, and power-
GND
switching circuitry is provided to the device on this pin.
Power-Fail Input. When PFI is less than 1.25V, PFO goes low; otherwise PFO
33
34
PFI
remains high. Connect PFI to GND or VCC when not used.
Active-Low SRAM Chip-Enable Input. CEI must be driven low to enable the external
CEI
SRAM.
Active-Low Power-Fail Output. Goes low and sinks current when PFI is less than
1.25V; otherwise PFO remains high.
35
36
PFO
CEO
Active-Low SRAM Chip-Enable Output. Chip-enable output for SRAM.
Active-Low Reset. The RST pin functions as a microprocessor reset signal. This pin
37
38
RST
has an internal 47kꢀ pullup resistor.
Digital Supply. DC power to the RTC, watchdog, X and Y drivers, and power-
switching circuitry is provided to the device on this pin.
VCC
3 of 23
DS1680
PIN
NAME
FUNCTION
Active-Low Strobe Input. The strobe input pin is used with the watchdog timer. If the
ST pin is not driven low within the watchdog time period, the RST pin is driven low.
Chip Select. The chip-select signal must be asserted high during a read or a write for
communication over the 3-wire serial interface.
39
ST
40
41
CS
External SRAM Power Supply Output. This pin is internally connected to VCC when
VCCO
VCC is within nominal limits. However, during power-fail VCCO is internally connected
to the VBAT pin. Switchover occurs when VCC drops below VCCSW
.
Serial Clock Input. SCLK is used to synchronize data movement on the serial
42
43
SCLK
I/O
interface.
Data Input/Output. The I/O pin is the bidirectional data pin for the 3-wire interface.
Interrupt Output. The INT pin is an active-high output that can be used as an interrupt
input to a microprocessor. The INT output remains high as long as the status bit
causing the interrupt is present and the corresponding interrupt-enable bit is set. The
44
INT
INT pin operates when the DS1680 is powered by VCC or VBAT
.
3-WIRE SERIAL INTERFACE
Communication with the RTC and watchdog is accomplished through a simple 3-wire interface
consisting of the chip select (CS), serial clock (SCLK), and input/output (I/O) pins.
All data transfers are initiated by driving the CS input high. The CS input serves two functions. First, CS
turns on the control logic, which allows access to the shift register for the address/command sequence.
Second, the CS signal provides a method of terminating either single byte or multiple byte (burst) data
transfer. A clock cycle is a sequence of a rising edge followed by a falling edge. For data input, data must
be valid during the clock’s rising edge and data bits are output on the clock’s falling edge. If the CS input
goes low, all data transfer terminates and the I/O pin goes to a high-impedance state.
Address and data bytes are always shifted LSB first into the I/O pin. Any transaction requires the
address/command byte to specify a read or write to a specific register followed by one or more bytes of
data. The address byte is always the first byte entered after CS is driven high. The most significant bit
(RD /WR) of this byte determines if a read or write will take place. If this bit is 0, one or more read cycles
will occur. If this bit is 1, one or more write cycles will occur.
Data transfers can occur one byte at a time or in multiple-byte burst mode. After CS is driven high an
address is written to the DS1680. After the address, one or more data bytes can be read or written. For a
single byte transfer one byte is read or written and then CS is driven low. Multiple bytes can be read or
written to the DS1680 after the address has been written. Each read or write cycle causes the register
address to automatically increment. Incrementing continues until the device is disabled. After accessing
register 0Dh, the address wraps to 00h.
Data transfer for single-byte transfer and multiple-byte burst transfer is illustrated in Figures 2 and 3.
4 of 23
DS1680
SINGLE-BYTE DATA TRANSFER Figure 2
MULTIPLE-BYTE BURST TRANSFER Figure 3
ADDRESS/COMMAND BYTE
Figure 4 shows the command byte for the DS1680. Each data transfer is initiated by a command byte.
Bits 0–6 specify the address of the registers to be accessed. The MSB (bit 7) is the read/write bit. This bit
specifies whether the accessed byte will be read or written. A read operation is selected if bit 7 is a zero
and a write operation is selected if bit 7 is a one. The address map for the DS1680 is shown in Figure 5.
ADDRESS/COMMAND BYTE Figure 4
7
6
5
4
3
2
1
0
RD
A6
A5
A4
A3
A2
A1
A0
WR
5 of 23
DS1680
RTC/WATCHDOG ADDRESS MAP Figure 5
BIT7
BIT0
00
01
02
0
0
0
10 SECONDS
SECONDS
MINUTES
HOURS
10 MINUTES
12
10 HR
10 HR
24
A/P
03
04
05
06
07
08
0
0
0
0
0
0
0
DAY
DATE
0
0
10 DATE
0
10 MO.
MONTH
YEAR
10 YEAR
M
M
M
10 SEC ALARM
10 MIN ALARM
SECONDS ALARM
MINUTES ALARM
HOUR ALARM
12
10 HR
10 HR
09
24
0A
0B
0C
0D
0E
M
0
0A/P
0
0
DAY ALARM
CONTROL REGISTER
STATUS REGISTER
WATCHDOG REGISTER
RESERVED
7F
CLOCK, CALENDAR, AND ALARM
The time and calendar information is accessed by reading/writing the appropriate register bytes. Note that
some bits are set to zero. These bits will always read zero regardless of how they are written. Also note
that registers 0Eh to 7Fh are reserved. These registers will always read zero regardless of how they are
written. The contents of the time, calendar, and alarm registers are in the binary-coded decimal (BCD)
format.
The DS1680 can run in either 12-hour or 24-hour mode. Bit 6 of the hours register is defined as the 12- or
24-hour mode select bit. When high, the 12-hour mode is selected. In the 12-hour mode, bit 5 is the
AM/PM bit with logic one being PM. In the 24-hour mode, bit 5 is the second 10-hour bit (20–23 hours).
The DS1680 also contains a time-of-day alarm. The alarm registers are located in registers 07h to 0Ah.
Bit 7 of each of the alarm registers are mask bits (Table 1). When all of the mask bits are logic 0, an
alarm will occur once per week when the values stored in time-keeping registers 00h to 03h match the
values stored in the time-of-day alarm registers. An alarm will be generated every day when mask bit of
the day alarm register is set to one. An alarm will be generated every hour when the day and hour alarm
mask bits are set to one. Similarly, an alarm will be generated every minute when the day, hour, and
minute alarm mask bits are set to one. When day, hour, minute, and second alarm mask bits are set to one,
an alarm will occur every second.
6 of 23
DS1680
TIME-OF-DAY ALARM BITS Table 1
ALARM REGISTER MASK BITS (BIT 7)
DESCRIPTION
SECONDS MINUTES HOURS
DAY
1
0
0
0
0
1
1
0
0
0
1
1
1
0
0
1
1
1
1
0
Alarm once per second.
Alarm when seconds match.
Alarm when minutes and seconds match.
Alarm when hours, minutes and seconds match.
Alarm when day, hours, minutes and seconds match.
SPECIAL PURPOSE REGISTERS
The DS1680 has two additional registers (control register and status register) that control the RTC and
interrupts.
CONTROL REGISTER – 0Bh
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
WP
SP1
SP0
0
0
0
AIE
EOSC
EOSC (Enable Oscillator). This bit, when set to logic 0, will start the oscillator. When this bit is set to a
logic 1, the oscillator is stopped and the DS1680 is placed into a low-power standby mode (IBAT) when in
battery-backup mode. When the DS1680 is powered by VCC, the oscillator is always on regardless of the
status of the EOSC bit; however, the RTC is incremented only when EOSC is a logic 0.
SP0 and SP1 (Speed Select). These bits select the on time of the X- and Y-measurement duty cycle. The
programmable duty cycle section has more detail.
WP (Write Protect). Before any write operation to the RTC or any other registers, this bit must be logic
0. When high, the write-protect bit prevents a write operation to any register.
AIE (Alarm Interrupt Enable). When set to a logic 1, this bit permits the interrupt request flag (IRQF)
bit in the status register to assert INT. When the AIE bit is set to logic 0, the IRQF bit does not initiate the
INT signal.
STATUS REGISTER – 0Ch
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
0
LOBAT
0
0
0
0
0
IRQF
LOBAT (Low Battery Flag). This bit reflects the status of the backup power source connected to the
V
BAT pin. When VBAT is greater than 2.5V, LOBAT is set to a logic 0. When VBAT is less than 2.3V,
LOBAT is set to a logic 1.
IRQF (Interrupt Request Flag). A logic 1 in the interrupt request flag bit indicates that the current time
has matched the time of day alarm registers. If the AIE bit is also a logic 1, the INT pin will go high.
IRQF is cleared by reading or writing to any of the alarm registers.
7 of 23
DS1680
POWER-UP/POWER-DOWN CONSIDERATIONS
When VCC is applied to the DS1680 and reaches a level greater than VCCTP (trip point), the device
becomes fully accessible after tRPU (250ms typical). Before tRPU elapses, some inputs are disabled. When
VCC drops below VCCSW, the device is switched over to the VBAT supply.
During power-up, when VCC returns to an in-tolerance condition, the RST pin is kept in the active state
for 250ms (typical) to allow the power supply and microprocessor to stabilize.
NONVOLATILE SRAM CONTROLLER
The DS1680 provides automatic backup and write protection for an external SRAM. This function is
provided by gating the chip-enable signal and by providing a constant power supply through the VCCO
pin.
The DS1680 nonvolatizes the external SRAM by write-protecting the SRAM and by providing a backup
power supply in the absence of VCC. When VCC falls below VCCTP, access to the external SRAM is
prohibited by forcing CE0 high regardless of the level of CEI . Upon power-up, access is prohibited until
the end of tRPU
.
POWER-FAIL COMPARATOR
The PFI input is connected to an internal reference. If PFI is less than 1.25V, PFO goes low. The power-
fail comparator can be used as an undervoltage detector to signal an impending power supply failure.
PFO can be used as a ꢀP interrupt input to prepare for power-down. For battery conservation, the
comparator is turned off and PFO is held low when in battery-backup mode.
ADDING HYSTERESIS TO THE POWER-FAIL COMPARATOR
Hysteresis adds a noise margin to the power-fail comparator and prevents PFO from oscillating when
VIN is near the power-fail comparator trip point. Figure 6 shows how to add hysteresis to the power-fail
comparator. Select the ratio of R1 and R2 such that PFI sees 1.25V when VIN falls to the desired trip
point (VTRIP). Resistors R2 and R3 adds hysteresis. R3 will typically be an order of magnitude greater
than R1 or R2. R3 should be chosen so it does not load down the PFO pin. Capacitor C1 adds noise
filtering and has a value of typically 1.0µF (See Figure 6 for a schematic diagram and equations.)
8 of 23
DS1680
POWER-FAIL COMPARATOR Figure 6
+5V
VCC
R1
VIN
PFI
C1
R2
R3
DS1680
PFO
GND
to µP
R2||R3
R1 + R2
R2
VH= 1.25 /
VTRIP = 1.25
R1 + R2||R3
1.25
R2
VI – 1.25
R1
5 - 1.25
+
=
R3
9 of 23
DS1680
MICROPROCESSOR MONITOR
The DS1680 monitors three vital conditions for a microprocessor: power supply, software execution, and
external override.
First, a precision temperature-compensated reference and comparator circuit monitors the status of VCC.
When an out-of-tolerance condition occurs, an internal power-fail signal is generated that forces the RST
pin to the active state, thus warning a processor-based system of impending power failure. When VCC
returns to an in-tolerance condition upon power-up, the reset signal is kept in the active state for tRST to
allow the power supply and microprocessor to stabilize. Note, however, that if the EOSC bit is set to a
logic 1 (to disable the oscillator during battery-backup mode), the RST signal will be kept in an active
state for tRST plus the start-up time of the oscillator.
The second monitoring function is pushbutton reset control. The DS1680 provides for a pushbutton
switch to be connected to the RST output pin. When the DS1680 is not in a reset cycle, it continuously
monitors the RST signal for a low-going edge. If an edge is detected, the DS1680 will debounce the
switch by pulling the RST line low. After the internal timer has expired, the DS1680 will continue to
monitor the RST line. If the line is still low, the DS1680 will continue to monitor the line looking for a
rising edge. Upon detecting release, the DS1680 will force the RST line low and hold it low for tRST
.
The third microprocessor monitoring function provided by the DS1680 is a watchdog timer. The
watchdog timer function forces RST to the active state when the ST input is not stimulated within the
predetermined time period. The time period is set by the time delay (TD) bits in the watchdog register.
The time delay can be set to 250ms, 500ms, or 1000ms. If TD0 and TD1 are both set to zero, the
watchdog timer is disabled. When enabled, the watchdog timer starts timing out from the set time period
as soon as RST is inactive. The default setting is for the watchdog timer to be enabled with 1000ms time
delay. If a high-to-low transition occurs on the ST input pin prior to time-out, the watchdog timer is reset
and begins to time-out again. If the watchdog timer is allowed to time-out, the RST signal is driven to the
active state for tRST. The ST input can be derived from microprocessor address signals, data signals,
and/or control signals. To guarantee that the watchdog timer does not time-out, a high-to-low transition
must occur at or less than the minimum period.
WATCHDOG REGISTER – 0Dh
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
0
0
0
0
0
0
TD1
TD0
WATCHDOG TIME-OUT BITS Table 2
TD1
TD0
WATCHDOG TIME-OUT
0
0
1
1
0
1
0
1
Watchdog Disabled
250ms
500ms
1000ms
10 of 23
DS1680
RESISTIVE TOUCH SCREEN (4-WIRE)
Resistive touch screens consist of two resistive plates that are separated by a small gap. Each plate has an
electrode at each end; when the screen is touched the pressure forces the two plates to come in contact at
the exact position of the touch. To get the x-coordinate position, the DS1680 will drive the X-plane
resistive film (via X+ and X-) and sense the voltage picked up by the Y-plane resistive film (via Y+ and
Y-). Next, to get the y-coordinate position, the DS1680 will drive the Y- plane resistive film and sense the
voltage picked up by the X-plane resistive film.
ANALOG-TO-DIGITAL CONVERTER (ADC)
The DS1680 provides a 10-bit ADC. Two multiplexed analog inputs are provided through the AIN0 and
AIN1 pins along with two other inputs on the X- and Y- pins. The ADC is monotonic (no missing codes)
and uses a successive approximation technique to convert the analog signal into a digital code.
An analog-to-digital conversion is the process of assigning a digital code to an analog input voltage. This
code represents the input value as a fraction of the full-scale voltage (FSV) range. The FSV range is then
divided by the ADC into 1024 codes (10 bits), and is bound by an upper limit equal to the reference
voltage and the lower limit, which is ground.
On-chip circuitry detects if the pen is in contact with the digitizer tablet. The pen-detection status is
indicated on pin (PEN_OFF) and can be used by the system for signaling end-of-stroke for handwriting
recognition software purposes. If no pen is detected, PEN_OFF will be pulled to logic 1 and no
coordinate data will be made available. PEN_OFF at logic 0 indicates that a pen is detected on the
digitizer tablet and its coordinate position will be made available on D0–D7. The NEW_DATA pin
pulses low to indicate when a new coordinate data pair is available.
When the AVG pin is set to logic 0, the data at pins D0–D7 will indicate the most recent sample of the
ADC. Setting the AVG pin to logic 1 invokes the data averaging mode. In this mode, the data output on
D0–D7 will indicate the rolling average of the four most recent samples of the ADC.
The DS1680 continuously monitors the CONVERT and ANSELIN signals; on the internal clock’s rising
edge (state cycle), the corresponding AIN0 or AIN1 conversion is requested. The conversion request
must be completed before T0 (Figure 7c) in order for AIN0 and/or AIN1 to be sampled and converted in
the present conversion cycle; otherwise AIN0 and/or AIN1 will be sampled and converted in the next
conversion cycle. The logic level of the ANSELIN input will determine whether a sample is taken from
the AIN0 or AIN1 input. Table 3 lists the specific analog input that is selected by this signal. Figure 8
shows the required timing associated with CONVERT and ANSELIN. If the state of ANSELIN changes
while CONVERT is at logic 1 and you meet the timing requirements of figure 8, both AIN0 and AIN1
conversions are requested. If the ANSELIN does not change states while CONVERT is at
logic 1, only AIN0 or AIN1 conversion is requested. If a pen is detected during a conversion request, then
X and Y will be sampled and converted prior to the AIN0 and/or AIN1 conversion. The AIN0 and AIN1
conversion result is output on the D0–D7 as defined in the Parallel Interface section.
ANALOG INPUT SELECTION Table 3
ANSELIN
ANALOG INPUT
AINO
0
1
AIN1
11 of 23
DS1680
PROGRAMMABLE DUTY CYCLE
The current required to take an X or Y measurement is VAVD / RD. In the case of RD = 250Ω and
VAVD = 5V, the current required is 20mA. The average current is the current during the measurement,
multiplied by the ratio of the time the drivers are on, to the power of total sample time. In order to
minimize the average current, the on-time should be limited to the minimum time required for the tablet
RC delay.
Experimental data suggests that a typical RC time constant is between 4µs and 5ꢀs for a resistive touch
screen. In order to achieve 10-bit resolution, the settling time must be eight time constants. This creates a
requirement of a minimum of 80ꢀs on-time total, 40ꢀs for each X and Y measurement.
To provide both low power and high sample rate, the on-time for the X- and Y-measurement duty cycle is
programmable. Bits 4 and 5 (SP0 and SP1) of the control register (0Bh) select the on-time of four
different frequency ranges. The frequencies given are the maximum frequency for that timing range,
which will not violate the 40ꢀs-per-measurement requirement.
AVERAGE
CURRENT (A)
870µ
NO. OF
SP1 SP0 FREQUENCY RANGE (MHz)
SAMPLES/SEC
CYCLES
0*
0
0*
1
2.0
2.8
4.0
5.0
543
760
5
7
1.217m
1
0
1.739m
1086
1359
10
13
1
1
2.261m
* Default setting.
Average current is the current required for the measurement, averaged out over the entire sample. This
average current is only related to the measurement phase when the drivers are on. The average current
will be drawn from the VCC supply. There is also current associated with the pen-detection phase, the
ADC, and the control logic.
The number of cycles indicated is the number of on-time state cycles. One state cycle is 16 main clock
cycles. If the frequency range is 2.0MHz, the state frequency is 2MHz/16 = 125kHz. There are 230 state
cycles in one complete sample. The number of cycles can be used to calculate the settling time and the
sample rate.
Example 1:
Frequency Range
:
:
2.0MHz
Input Clock Frequency
1.8432MHz
tsettle = (1 / 1.8432e6) x 16 x 5 = 43.4ꢀs
Iavg = (10 / 230) x 20mA = 870ꢀA
Sample Rate = 1.8432e6 / (16 x 230) = 501 samples/sec
Example 2:
Frequency Range
Input Clock Frequency
:
:
2.8MHz
1.8432MHz
tsettle = (1 / 1.8432e6) x 16 x 7 = 60.8ꢀs
Iavg = (14 / 230) / x 20mA = 1.217mA
Sample Rate = 1.8432e6 / (16 x 230) = 501 samples/sec
12 of 23
DS1680
CONVERSION TIMING Figure 7a
Pen Down
X - Y
A0 - A1
Measure
Measure
PD
X
Y
PD A0 A1 PD
X
Y
PD A0 A1 PD
X
Y
PD A0 A1 PD
X
Y
PD A0 A1 PD
X
Y
PD
PEN_OFF
AVG = 0 (Disabled)
AVG = 1 (Enabled)
NEW_DATA
NEW_DATA
X to Y MEASUREMENT Figure 7b
115 state cycles
30
10-18 13-5
28-36
13-5
21
30
111001 00
X-drivers
on
111001 00
Y-drivers
on
PD
PD
1 State Cycle = 16 Main Clock Cycles
AIN0 to AIN1 MEASUREMENT Figure 7c
115 state cycles
30
18
6
35
6
20
30
PD
A0
A1
PD
1 State Cycle = 16 Main Clock Cycles
T0
13 of 23
DS1680
CONVERT AND ANSELIN TIMING Figure 8
must be at least
2 state cycles
CONVERT
AIN0 conversion requested
ANSELIN = 0
must be at least 4 state cycles
CONVERT
ANSELIN
both AIN0 and AIN1 conversion requested
must be at least
2 state cycles
must be at least
2 state cycles
must be at least
2 state cycles
CONVERT
AIN1 conversion requested
ANSELIN = 1
14 of 23
DS1680
PARALLEL INTERFACE
The ADC output is available on the data bus at pins D0–D7. A logic 0 on COEN will enable data onto the
data bus so that the DS1680 can be used in parallel with other devices. PEN_SELECT and
OUT_SELECT are used to decode which analog output (X-, Y-, AIN0, or AIN1) is output on the data bus
when COEN is asserted low. Since the device offers 10-bit resolution, the BHE pin is used to decode the
10 bits of data on the data bus. A logic 1 on BHE will enable data bits B2–B9. A logic 0 will enable data
bits B0–B1 along with the six LSBs = 0. The status pin ( NEW_DATA ) pulses low to indicate that new
coordinate or conversion is available. The output can be read while NEW_DATA is low or after it has
gone high. Output selection and parallel data format is shown below.
OUTPUT SELECTION Table 4
PEN_SELECT
OUT_SELECT
ANALOG OUTPUT
0
0
1
1
0
1
0
1
AIN0
AIN1
X-
Y-
PARALLEL DATA FORMAT
MSB
LSB
B2
0
High Byte
Low Byte
BHE = 1
BHE = 0
B9
B1
B8
B0
B7
0
B6
0
B5
0
B4
0
B3
0
POWER MANAGEMENT (ADC AND PEN-INPUT PROCESSOR)
The DS1680 analog circuitry can be placed into a low-power mode by asserting and holding the
PD_RESET pin at logic 1. Normal operation will resume when PD_RESET is returned to logic 0.
To further conserve power, the pen-detection circuitry will automatically switch the analog circuitry to
power-down mode whenever there is no pen input detected for more than three seconds. Normal
operation will automatically resume when any one of the following three events occur: pen down is
detected, the CONVERT signal is activated, or chip is reset (PD_RESET pulled to logic 1 and then
returned to logic 0).
15 of 23
DS1680
ABSOLUTE MAXIMUM RATINGS
Voltage Range on Any Pin Relative to Ground……………………………………………..-0.3V to +7.0V
Operating Temperature Range…………………………………………………………….…..0LC to +70LC
Storage Temperature Range……………………………………………………………….-55LC to +125LC
Soldering Temperature………………………………………….See IPC/JEDEC J-STD-020 Specification
This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in
the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended
periods of time can affect device reliability.
RECOMMENDED DC OPERATING CONDITIONS
(TA = 0LC to +70LC)
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS NOTES
V
CC, VAVD,
3.3V
5V
2.97
3.3
3.63
V
Digital Power Supply
V
REF
Voltage
VCC, VAVD,
VREF
4.5
2.0
5.0
5.5
V
V
VCC
0.3
+
Input Logic 1
VIH
Input Logic 0
VIL
-0.3
2.5
+0.8
3.7
V
V
Battery Voltage
VBAT
DC ELECTRICAL CHARACTERISTICS (VCC = 5.0V ±10%, TA = 0LC to +70LC.)
PARAMETER
SYMBOL MIN
TYP
MAX UNITS NOTES
Input Leakage
ILI
ILO
-1
+1
ꢀA
ꢀA
V
CS Leakage
260
7
1
Logic 1 Output (IOUT = -0.4mA)
Logic 0 Output (IOUT = 1.5mA)
Active Supply Current (No Pen Detect)
Active Supply Current (Pen Detected)
Standby Current
VOH
VOL
2.4
0.4
500
5
300
500
100
87
4.50
2.78
2.0
0.8
V
2
ICCA
ICCPD
ICCS
200
µA
mA
ꢀA
nA
nA
kꢁ
V
3
19
4
175
300
Oscillator Current
IOSC
17
18
Battery Current (Oscillator Off)
Internal RST Pullup Resistor
VCC Trip Point
IBAT
RP
25
4.15
47
4.33
2.67
VCCTP
VCCSW
PBDV
PBRD
VCC Switchover
V
12, 20
Pushbutton Detect
0.8
V
Pushbutton Release
0.3
V
VCC
0.3
-
Output Voltage
VCCO
V
11
VCCO Output Current (Source = VCC)
VCCO Output Current (Source = VBAT)
PFI Input Threshold
ICCO1
ICCO2
VPFI
IPFI
VOH
VOL
150
150
1.35
mA
ꢀA
V
13
14
1.15
-25
1.25
PFI Input Leakage
+25
nA
VCC
-
V
PFO Output Voltage (IOH = -0.4mA)
PFO Output Voltage (IOL = 1.5mA)
1.5
0.4
V
16 of 23
DS1680
DC ELECTRICAL CHARACTERISTICS (VCC = 3.3V ±10%, TA = 0LC to +70LC.)
PARAMETER
SYMBOL MIN
TYP
MAX
+1
UNITS NOTES
Input Leakage
ILI
ILO
-1
ꢀA
CS Leakage
170
7
1
ꢀA
V
Logic 1 Output (IOUT = -0.4mA)
Logic 0 Output (IOUT = 1.5mA)
Active Supply Current (No Pen Detect)
Active Supply Current (Pen Detected)
Standby Current
VOH
VOL
2.4
0.4
300
3
200
500
100
87
2.97
2.78
2.0
0.8
V
2
ICCA
ICCPD
ICCS
115
µA
mA
ꢀA
nA
nA
kꢁ
V
3
19
4
110
300
Oscillator Current
IOSC
17
18
Battery Current (Oscillator Off)
Internal RST Pullup Resistor
VCC Trip Point
IBAT
RP
25
2.75
47
2.86
2.67
VCCTP
VCCSW
PBDV
PBRD
VCCO
ICCO1
ICCO2
VPFI
IPFI
VCC Switchover
V
12, 20
Pushbutton Detect
0.8
V
Pushbutton Release
0.3
V
Output Voltage
VCC-0.3
V
11
13
14
VCCO Output Current (Source = VCC)
VCCO Output Current (Source = VBAT)
PFI Input Threshold
80
100
1.35
25
mA
ꢀA
V
1.15
-25
1.25
PFI Input Leakage
nA
VOH
VOL
VCC-1.5
V
V
PFO Output Voltage (IOH = -0.4mA)
PFO Output Voltage (IOL = 1.5mA)
0.4
CAPACITANCE
PARAMETER
(TA = +25LC)
SYMBOL
MIN
TYP
10
MAX
UNITS NOTES
Input Capacitance
I/O Capacitance
CI
CI/O
CX
pF
pF
pF
15
Crystal Capacitance
6
3-WIRE INTERFACE CHARACTERISTICS
(VCC = 5.0V ±10%, TA = 0LC to +70LC.)
PARAMETER
Data to Clock Setup
SYMBOL
tDC
MIN
50
TYP
MAX
UNITS NOTES
ns
ns
8
CLK to Data Hold
CLK to Data Delay
CLK to Low Time
CLK to High Time
CLK Frequency
tCDH
tCDD
tCL
70
8
200
ns
8, 9, 10
250
250
ns
ns
8
8
8
tCH
tCLK
tR, tF
tCC
2.0
MHz
ns
CLK Rise and Fall
CS to CLK Setup
CLK to CS Hold
CS Inactive Time
CS to I/O High-Z
500
1
250
1
8
8
8
8
ꢀs
tCCH
tCWH
tCDZ
ns
ꢀs
70
ns
17 of 23
DS1680
3-WIRE INTERFACE CHARACTERISTICS
(VCC = 3.3V ±10%, TA = 0LC to +70LC.)
PARAMETER
Data to Clock Setup
CLK to Data Hold
CLK to Data Delay
CLK to Low Time
CLK to High Time
CLK Frequency
SYMBOL
tDC
MIN
150
TYP
MAX
UNITS NOTES
ns
ns
8
tCDH
tCDD
tCL
210
8
600
ns
8, 9, 10
750
750
ns
8
8
8
tCH
ns
tCLK
tR, tF
tCC
0.667
1500
MHz
ns
CLK Rise and Fall
CS to CLK Setup
CLK to CS Hold
CS Inactive Time
CS to I/O High-Z
3
750
3
8
8
8
8
ꢀs
tCCH
tCWH
tCDZ
ns
ꢀs
210
ns
ADC CHARACTERISTICS
(VCC, VAVD = 5.0V ±10%, TA = 0LC to +70LC.)
PARAMETER
SYMBOL MIN
TYP
MAX
UNITS NOTES
ꢁ
Resistance of Digitizer Film
RD
250
600
1000
Resistance of On-Chip Driver
Parasitic Capacitance Between X-
and Y-Plates of Digitizer
RDRIVER
12
5
25
10
ꢁ
nF
kꢁ
CXY
Ladder Resistance
ADC Active Current
ADC Standby Current
Reference Current
Input Leakage (AIN0, AIN1)
Analog Input Capacitance
Resolution
RREF
IAVDA
IAVDS
IREF
8
25
450
120
200
10
60
650
200
650
5
6
ꢀA
ꢀA
ꢀA
ILI
nA
CIN
10
15
pF
10
Bits
LSB
LSB
LSB
%
Differential Nonlinearity
Integral Nonlinearity
Offset Error
EDL
EIL
M0.5
M0.5
M1.0
M0.25
M1.0
M1.0
M1.5
M1.0
5.0
EOS
Gain Error
EG
ADC Clock Frequency
FOSCIN
MHz
Multiplexer Selector Path
tMUX
tOEA
tOEZ
60
40
40
ns
ns
ns
Propagation Delay
COEN Falling Edge to Data Bus
Driven
COEN Rising Edge to Data Bus
High-Z
18 of 23
DS1680
ADC CHARACTERISTICS
(VCC, VAVD = 3.3V ±10%, TA = 0LC to +70LC.)
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS NOTES
ꢁ
Resistance of Digitizer Film
RD
250
600
1000
Resistance of On-Chip Driver
Parasitic Capacitance Between X-
and Y-Plates of Digitizer
RDRIVER
CXY
15
5
30
10
ꢁ
nF
kꢁ
Ladder Resistance
ADC Active Current
ADC Standby Current
Reference Current
Input Leakage (AIN0, AIN1)
Analog Input Capacitance
Resolution
RREF
IAVDA
IAVDS
IREF
8
25
320
50
60
450
150
550
5
6
ꢀA
ꢀA
150
10
ꢀA
ILI
nA
CIN
10
15
pF
10
Bits
LSB
LSB
LSB
%
Differential Nonlinearity
Integral Nonlinearity
Offset Error
EDL
EIL
M0.5
M0.5
M1.0
M0.25
M1.0
M1.0
M1.5
M1.0
2.5
EOS
Gain Error
EG
ADC Clock Frequency
FOSCIN
MHz
Multiplexer Selector Path
tMUX
tOEA
tOEZ
120
80
ns
ns
ns
Propagation Delay
COEN Falling Edge to Data Bus
Driven
COEN Rising Edge to Data Bus
80
High-Z
POWER-FAIL AND RESET CHARACTERISTICS
(VCC = 5.0V ±10%, TA = 0LC to +70LC.)
PARAMETER
PFI Low to PFO Low
SYMBOL
MIN
TYP
MAX
UNITS NOTES
tPFD
100
ns
tPFU
100
100
ns
ns
ms
ms
ms
ns
PFI High to PFO High
tRPD
tRPU
tRST
PBDB
tST
VCC Detect to RST (VCC Falling)
VCC Detect to RST (VCC Rising)
Reset Active Time
250
250
250
15,16
15
Pushbutton Debounce
15
20
ST Pulse Width
Chip-Enable Propagation Delay to
External SRAM
tCED
tFB
8
15
ns
µs
VCCTP(MAX) to VCCSW(MIN) Fall Time
200
20
19 of 23
DS1680
POWER-FAIL AND RESET CHARACTERISTICS
(VCC = 3.3V ±10%, TA = 0ºC to +70ºC.)
PARAMETER
PFI Low to PFO Low
SYMBOL
MIN
TYP
MAX
UNITS NOTES
tPFD
200
ns
tPFU
200
200
ns
ns
ms
ms
ms
ns
PFI High to PFO High
tRPD
tRPU
tRST
PBDB
tST
VCC Detect to RST (VCC Falling)
VCC Detect to RST (VCC Rising)
Reset Active Time
250
250
250
15, 16
15
Pushbutton Debounce
15
40
50
ST Pulse Width
Chip-Enable Propagation Delay to
tCED
tFB
8
15
ns
µs
External SRAM
VCCTP(MAX) to VCCSW(MIN) Fall Time
20
PARALLEL INTERFACE OUTPUT TIMING Figure 9
COEN
tOEA
tOEZ
PEN_SELECT
tMUX
OUT_SELECT
tMUX
tMUX
BHE
tMUX
tMUX
tMUX
tMUX
X,
HIGH
X,
LOW
Y,
HIGH
Y,
LOW
AIN0,
HIGH
AIN0,
LOW
AIN1,
LOW
AIN1,
LOW
D0 - D7
20 of 23
DS1680
3-WIRE TIMING DIAGRAM: READ DATA Figure 10
3-WIRE TIMING DIAGRAM: WRITE DATA Figure 11
PUSHBUTTON RESET Figure 12
21 of 23
DS1680
VCC POWER-UP Figure 13
VCC POWER-DOWN Figure 14
POWER-FAIL WARNING Figure 15
22 of 23
DS1680
NOTES:
1. Logic 1 voltages are specified at VCC = 3.3V or 5.0V, VOH = VCC for capacitive loads. Exclude RST
pin.
2. Logic 0 voltages are specified at VCC = 3.3 or 5.0V, VOL = GND for capacitive loads.
3. ICCA is specified with outputs open, CS set to a logic 1, SCLK = 500kHz, oscillator enabled, ADC
disabled, and no pen detected.
4. ICCS is specified with CS, VCCO open and I/O, SCLK at logic 0, ADC disabled, and no pen detected.
5. IAVDA is specified with ADC enabled.
6. IAVDS is specified with ADC disabled.
7. CS has a 40kꢁ pulldown resistor to ground.
8. Measured at VIH = 2.0V or VIL = 0.8V and 10ns maximum rise and fall time.
9. Measured at VOH = 2.4V or VOL = 0.4V.
10. Load capacitance = 25pF.
11. ICCO = 100 mA, VCC > VCCTP
.
12. VCCO switchover from VCC to VBAT occurs when VCC drops below the lower of VCCSW and VBAT
13. Current from VCC input pin to VCCO output pin.
.
14. Current from VBAT input pin to VCCO output pin.
15. Time base is generated by the crystal oscillator. Accuracy of this time period is based on the 32kHz
crystal that is used. A typical crystal with a specified load capacitance of 6pF will provide accuracy
within M100ppm over the 0LC to +70LC temperature range. For greater accuracy, see the DS32kHz
data sheet.
16. If the EOSC bit in the control register is set to a logic 1, tRPU is equal to 250ms plus the start-up time
of the crystal oscillator.
17. VCC = 0V, VAVD = 0V, VBAT = 3.7V. and oscillator enabled. Measured without RAM connected.
18. VCC = 0V, VAVD = 0V, VBAT = 3.7V, and oscillator disabled. Measured without RAM connected.
19. ICCPD is specified with outputs open, CS set to a logic 1, SCLK = 500kHz, oscillator enabled, ADC
enabled, and pen detected.
20. Under certain slew rate conditions, VSW can be as low as 1.8V.
PACKAGE INFORMATION
(For the latest package outline information, go to www.maxim-ic.com/DallasPackInfo.)
23 of 23
Maxim/Dallas Semiconductor cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim/Dallas Semiconductor product.
No circuit patent licenses are implied. Maxim/Dallas Semiconductor reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2005 Maxim Integrated Products S Printed USA
The Maxim logo is a registered trademark of Maxim Integrated Products, Inc. The Dallas logo is a registered trademark of Dallas Semiconductor Corporation.
相关型号：
DS1682S+
Time Recorder, Non-Volatile, 0 Timer(s), CMOS, PDSO8, 0.150 INCH, ROHS COMPLIANT, SOP-8
MAXIM
DS1682S+T&R
Time Recorder, Non-Volatile, 0 Timer(s), CMOS, PDSO8, 0.150 INCH, ROHS COMPLIANT, SOP-8
MAXIM
©2020 ICPDF网 联系我们和版权申明