MAX5974BETE [MAXIM]
Active-Clamped, Spread-Spectrum, Current-Mode PWM Controllers; 有源钳位,扩频,电流模式PWM控制器![MAX5974BETE](http://pdffile.icpdf.com/pdf1/p00178/img/icpdf/MAX59_1003566_icpdf.jpg)
型号: | MAX5974BETE |
厂家: | ![]() |
描述: | Active-Clamped, Spread-Spectrum, Current-Mode PWM Controllers |
文件: | 总27页 (文件大小:2594K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
19-5331; Rev 2; 6/11
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
General Description
Features
S Peak Current-Mode Control, Active-Clamped
The MAX5974_ provide control for wide-input-voltage,
active-clamped, current-mode PWM, forward converters
in Power-over-Ethernet (PoE) powered device (PD) appli-
cations. The MAX5974A/MAX5974C are well-suited for
universal or telecom input range, while the MAX5974B/
MAX5974D also accommodate low input voltage down
to 10.5V.
Forward PWM Controller
S Regulation Without Optocoupler (MAX5974A/
MAX5974B)
S Internal 1% Error Amplifier
S 100kHz to 600kHz Programmable Q8% Switching
Frequency, Synchronization Up to 1.2MHz
The devices include several features to enhance supply
efficiency. The AUX driver recycles magnetizing cur-
rent instead of wasting it in a dissipative clamp circuit.
Programmable dead time between the AUX and main
driver allows for zero-voltage switching (ZVS). Under light-
load conditions, the devices reduce the switching fre-
quency (frequency foldback) to reduce switching losses.
S Programmable Frequency Dithering for Low-EMI,
Spread-Spectrum Operation
S Programmable Dead Time, PWM Soft-Start,
Current Slope Compensation
S Programmable Feed-Forward Maximum Duty-
Cycle Clamp, 80% Maximum Limit
S Frequency Foldback for High-Efficiency Light-
The MAX5974A/MAX5974B feature unique circuitry to
achieve output regulation without using an optocoupler,
while the MAX5974C/MAX5974D utilize the traditional
optocoupler feedback method. An internal error amplifier
with a 1% reference is very useful in nonisolated design,
eliminating the need for an external shunt regulator.
Load Operation
S Internal Bootstrap UVLO with Large Hysteresis
S 100µA (typ) Startup Supply Current
S Fast Cycle-by-Cycle Peak Current-Limit, 35ns
Typical Propagation Delay
S 115ns Current-Sense Internal Leading-Edge
The devices feature a unique feed-forward maximum
duty-cycle clamp that makes the maximum clamp volt-
age during transient conditions independent of the line
voltage, allowing the use of a power MOSFET with lower
breakdown voltage. The programmable frequency dither-
ing feature provides low-EMI, spread-spectrum operation.
Blanking
S Output Short-Circuit Protection with Hiccup Mode
S Reverse Current Limit to Prevent Transformer
Saturation Due to Reverse Current
S Internal 18V Zener Clamp on Supply Input
S 3mm x 3mm, Lead-Free, 16-Pin TQFN-EP
The MAX5974_ are available in 16-pin TQFN-EP pack-
ages and are rated for operation over the -40°C to +85°C
temperature range.
Applications
PoE IEEE® 802.3af/at Powered Devices
High-Power PD (Beyond the 802.3af/at Standard)
Active-Clamped Forward DC-DC Converters
IP Phones
Wireless Access Nodes
Security Cameras
Ordering Information/Selector Guide
PART
TOP MARK
+AHY
PIN-PACKAGE
16 TQFN-EP*
16 TQFN-EP*
16 TQFN-EP*
16 TQFN-EP*
UVLO THRESHOLD (V)
FEEDBACK MODE
Sample/Hold
MAX5974AETE+
MAX5974BETE+
MAX5974CETE+
MAX5974DETE+
16
8.4
16
+AHZ
Sample/Hold
+AIA
Continuously Connected
Continuously Connected
+AIB
8.4
Note: All devices are specified over the -40°C to +85°C operating temperature range.
+Denotes a lead(Pb)-free/RoHS-compliant package.
*EP = Exposed pad.
IEEE is a registered service mark of the Institute of Electrical and Electronics Engineers, Inc.
_______________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
ABSOLUTE MAXIMUM RATINGS
IN to GND (V = 0V)...........................................-0.3V to +26V
IN, NDRV, AUXDRV ......................................................100mA
EN
NDRV, AUXDRV (pulsed for less than 100ns).................. Q1A
EN, NDRV, AUXDRV to GND .....................-0.3V to (V + 0.3V)
IN
RT, DT, FFB, COMP, SS, DCLMP, DITHER/SYNC
Continuous Power Dissipation (T = +70NC) (Note 1)
A
to GND .................................................................-0.3V to +6V
FB to GND (MAX5974A/MAX5974B only)..................-6V to +6V
FB to GND (MAX5974C/MAX5974D only) ..............-0.3V to +6V
CS, CSSC to GND...................................................-0.8V to +6V
PGND to GND ......................................................-0.3V to +0.3V
Maximum Input/Output Current (continuous)
16-Pin TQFN (derate 20.8mW/NC above +70NC).......1666mW
Operating Temperature Range.......................... -40NC to +85NC
Maximum Junction Temperature.....................................+150NC
Storage Temperature Range............................ -65NC to +150NC
Lead Temperature (soldering, 10s) ................................+300NC
Soldering Temperature (reflow) ......................................+260NC
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
PACKAGE THERMAL CHARACTERISTICS (Note 1)
Junction-to-Ambient Thermal Resistance (B )..............48NC/W
JA
Junction-to-Case Thermal Resistance (B ).....................7NC/W
JC
Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-
layer board. For detailed information on package thermal considerations, refer to www.maxim-ic.com/thermal-tutorial.
ELECTRICAL CHARACTERISTICS
(V = 12V (for MAX5974A/MAX5974C, bring V up to 17V for startup), V
= V
= V
= V = V
= V
=
DCLMP
IN
IN
CS
CSSC
DITHER/SYNC
FB
FFB
V , V = +2V, NDRV = AUXDRV = SS = COMP = unconnected, R = 34.8kI, R = 25kI, C = 1FF, T = -40NC to +85NC,
GND EN RT DT IN A
unless otherwise noted. Typical values are at T = +25NC.) (Note 2)
A
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
UNDERVOLTAGE LOCKOUT/STARTUP (IN)
MAX5974A/
MAX5974C
15.4
8
16
16.5
8.85
Bootstrap UVLO Wakeup Level
V
V
V
rising
falling
V
INUVR
IN
MAX5974B/
MAX5974D
8.4
Bootstrap UVLO Shutdown
Level
V
6.65
17
7
7.35
20
V
V
INUVF
IN
IN Clamp Voltage
V
I
IN
= 2mA (sinking)
18.5
IN_CLAMP
V
IN
= +15V (for MAX5974A/
IN Supply Current in
Undervoltage Lockout
MAX5974C);
= +7.5V (for MAX5974B/MAX5974D),
when in bootstrap UVLO
I
100
1.8
150
3
FA
START
V
IN
IN Supply Current After Startup
I
V
IN
= +12V
mA
C
ENABLE (EN)
V
V
V
rising
falling
1.17
1.09
1.215
1.14
1.26
1.19
1
ENR
EN
Enable Threshold
V
V
ENF
EN
Input Current
I
FA
EN
OSCILLATOR (RT)
RT Bias Voltage
V
RT
1.23
V
NDRV Switching Frequency
Range
f
100
600
kHz
SW
2
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
ELECTRICAL CHARACTERISTICS (continued)
(V = 12V (for MAX5974A/MAX5974C, bring V up to 17V for startup), V
= V
= V
= V = V
= V
=
DCLMP
IN
IN
CS
CSSC
DITHER/SYNC
FB
FFB
V
, V = +2V, NDRV = AUXDRV = SS = COMP = unconnected, R = 34.8kI, R = 25kI, C = 1FF, T = -40NC to +85NC,
GND EN
RT
DT
IN
A
unless otherwise noted. Typical values are at T = +25NC.) (Note 2)
A
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
+8
UNITS
%
NDRV Switching Frequency
Accuracy
-8
Maximum Duty Cycle
D
MAX
f
= 250kHz
79
80
82
%
SW
SYNCHRONIZATION (SYNC)
Synchronization Logic-High
Input
V
f
2.91
V
IH-SYNC
SYNCIN
Synchronization Pulse Width
50
ns
Synchronization Frequency
Range
1.1 x
2 x
f
SW
kHz
f
SW
Maximum Duty Cycle During
Synchronization
D
x f
SW
/
MAX
SYNC
%
f
DITHERING RAMP GENERATOR (DITHER)
Charging Current
V
V
= 0V
45
43
50
50
2
55
57
FA
FA
V
DITHER
Discharging Current
= 2.2V
DITHER
Ramp’s High Trip Point
Ramp’s Low Trip Point
0.4
V
SOFT-START AND RESTART (SS)
Charging Current
I
I
9.5
10
10.5
2
FA
SS-CH
I
V
= 2V, normal shutdown
0.65
1.34
mA
SS-D
SS
(V < V
or V < V
),
EN
ENF
IN
INUVF
Discharging Current
V
SS
= 2V, hiccup mode discharge for
1.6
2
2.4
FA
SS-DH
t
(Note 3)
RSTRT
Discharge Threshold to Disable
Hiccup and Restart
V
0.15
V
SS-DTH
Minimum Restart Time During
Hiccup Mode
Clock
Cycles
t
1024
5
RSTRT-MIN
Normal Operating High Voltage
Duty-Cycle Control Range
DUTY-CYCLE CLAMP (DCLMP)
DCLMP Input Current
V
SS-HI
V
V
V
D
(typ) = (V /2.43V)
SS-DMAX
0
2
SS-DMAX
MAX
I
V
= 0 to 5V
-100
73
0
+100
77.5
58
nA
%
DCLMP
DCLMP
V
V
V
= 0.5V
= 1V
75.4
56
DCLMP
DCLMP
DCLMP
Duty-Cycle Control Range
V
54
DCLMP-R
D
MAX
(typ) =
1 - (V
/2.43V)
DCLMP
= 2V
14.7
16.5
18.3
NDRV DRIVER
Pulldown Impedance
Pullup Impedance
Peak Sink Current
Peak Source Current
Fall Time
R
I
I
(sinking) = 100mA
(sourcing) = 50mA
1.9
4.7
1
3.4
8.3
I
I
NDRV-N
NDRV
R
NDRV-P
NDRV
A
0.65
14
A
t
C
C
= 1nF
= 1nF
ns
ns
NDRV-F
NDRV
Rise Time
t
27
NDRV-R
NDRV
3
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
ELECTRICAL CHARACTERISTICS (continued)
(V = 12V (for MAX5974A/MAX5974C, bring V up to 17V for startup), V
= V
= V
= V = V
= V
=
DCLMP
IN
IN
CS
CSSC
DITHER/SYNC
FB
FFB
V , V = +2V, NDRV = AUXDRV = SS = COMP = unconnected, R = 34.8kI, R = 25kI, C = 1FF, T = -40NC to +85NC,
GND EN RT DT IN A
unless otherwise noted. Typical values are at T = +25NC.) (Note 2)
A
PARAMETER
AUXDRV DRIVER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Pulldown Impedance
Pullup Impedance
Peak Sink Current
Peak Source Current
Fall Time
R
I
I
(sinking) = 50mA
(sourcing) = 25mA
4.3
10.6
0.5
0.3
24
7.7
I
I
AUX-N
AUXDRV
R
18.9
AUX-P
AUXDRV
A
A
t
C
C
= 1nF
= 1nF
ns
ns
AUX-F
AUXDRV
Rise Time
t
45
AUX-R
AUXDRV
DEAD-TIME PROGRAMMING (DT)
DT Bias Voltage
V
1.215
40
V
DT
R
DT
R
DT
R
DT
R
DT
= 10kI
From NDRV falling
to AUXDRV falling
ns
= 100kI
= 10kI
300
310
350
40
410
420
NDRV to AUXDRV Delay
(Dead Time)
t
DT
From AUXDRV rising
to NDRV rising
ns
= 100kI
360
CURRENT-LIMIT COMPARATOR (CS)
Cycle-by-Cycle Peak
Current-Limit Threshold
V
375
393
410
-88
mV
mV
CS-PEAK
Cycle-by-Cycle Reverse
Current-Limit Threshold
Turns AUXDRV off for the remaining
cycle if reverse current limit is exceeded
V
-118
-100
CS-REV
Current-Sense Blanking Time
for Reverse Current Limit
t
CS-BLANK-
REV
From AUXDRV falling edge
115
8
ns
Events
ns
Number of Consecutive Peak
Current-Limit Events to Hiccup
N
HICCUP
Current-Sense Leading-Edge
Blanking Time
t
From NDRV rising edge
115
CS-BLANK
From CS rising (10mV overdrive) to
NDRV falling (excluding leading-edge
blanking)
Propagation Delay from
Comparator Input to NDRV
t
35
ns
ns
PDCS
Minimum On-Time
t
100
47
150
200
58
ON-MIN
SLOPE COMPENSATION (CSSC)
Slope Compensation Current
Ramp Height
Current ramp’s peak added to CSSC
input per switching cycle
52
FA
PWM COMPARATOR
Comparator Offset Voltage
Current-Sense Gain
V
V
- V
CSSC
1.35
3.1
1.7
2
V
PWM-OS
COMP
A
DV
/DV (Note 4)
COMP CSSC
3.33
3.6
V/V
CS-PWM
Current-Sense Leading-Edge
Blanking Time
t
From NDRV rising edge
Change in V = 10mV (including
115
150
ns
ns
CSSC-BLANK
CSSC
Comparator Propagation Delay
t
PWM
internal leading-edge blanking)
4
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
ELECTRICAL CHARACTERISTICS (continued)
(V = 12V (for MAX5974A/MAX5974C, bring V up to 17V for startup), V
= V
= V
= V = V
= V
=
DCLMP
IN
IN
CS
CSSC
DITHER/SYNC
FB
FFB
V , V = +2V, NDRV = AUXDRV = SS = COMP = unconnected, R = 34.8kI, R = 25kI, C = 1FF, T = -40NC to +85NC,
GND EN RT DT IN A
unless otherwise noted. Typical values are at T = +25NC.) (Note 2)
A
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
ERROR AMPLIFIER
MAX5974A/
MAX5974B
1.5
1.202
-250
-500
1.52
1.54
1.227
+250
+100
V
V
when I
= 0,
FB
COMP
FB Reference Voltage
V
V
REF
= 2.5V
COMP
MAX5974C/
MAX5974D
1.215
MAX5974A/
MAX5974B
FB Input Bias Current
Voltage Gain
I
V
= 0 to 1.75V
FB
nA
dB
mS
FB
MAX5974C/
MAX5974D
A
80
EAMP
MAX5974A/
MAX5974B
1.8
1.8
2.55
3.2
3.5
Transconductance
g
M
MAX5974C/
MAX5974D
2.66
2
MAX5974A/
MAX5974B
Open loop (typical gain
= 1) -3dB frequency
Transconductance Bandwidth
BW
MHz
MAX5974C/
MAX5974D
30
Source Current
V
V
= 1V, V
= 2.5V
300
300
375
375
455
455
FA
FA
FB
FB
COMP
Sink Current
= 1.75V, V
= 1V
COMP
FREQUENCY FOLDBACK (FFB)
V
Gain
-to-FFB Comparator
CSAVG
10
30
V/V
FA
FFB Bias Current
I
V
= 0V, V = 0V (not in FFB mode)
26
33
FFB
FFB
CS
NDRV Switching Frequency
During Foldback
f
f
/2
SW
kHz
SW-FB
Note 2: All devices are 100% production tested at T = +25NC. Limits over temperature are guaranteed by design.
A
Note 3: See the Output Short-Circuit Protection with Hiccup Mode section.
Note 4: The parameter is measured at the trip point of latch with V = 0V. Gain is defined as DV
/DV
for 0.15V <
FB
COMP
CSSC
DV
< 0.25V.
CSSC
5
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
Typical Operating Characteristics
(V = 12V (for MAX5974A/MAX5974C, bring V up to 17V for startup), V
= V
= V
= V = V
= V
=
DCLMP
IN
IN
CS
CSSC
DITHER/SYNC
FB
FFB
V
, V = 2V, NDRV = AUXDRV = SS = COMP = unconnected, R = 34.8kI, R = 25kI, unless otherwise noted.)
GND EN RT DT
IN UVLO WAKE-UP LEVEL
vs. TEMPERATURE
IN UVLO WAKE-UP LEVEL
vs. TEMPERATURE
IN UVLO SHUTDOWN LEVEL
vs. TEMPERATURE
16.3
8.6
8.5
8.4
8.3
8.2
8.1
8.0
7.3
7.2
7.1
7.0
6.9
6.8
MAX5974A/MAX5974C
MAX5974B/MAX5974D
16.2
16.1
16.0
15.9
15.8
15.7
-40
-15
10
35
60
85
-40
-15
10
35
60
85
-40
-40
0
-15
10
35
60
85
TEMPERATURE (°C)
TEMPERATURE (°C)
TEMPERATURE (°C)
EN RISING THRESHOLD
vs. TEMPERATURE
EN FALLING THRESHOLD
vs. TEMEPRATURE
UVLO SHUTDOWN CURRENT
vs. TEMPERATURE
1.220
1.218
1.216
1.214
1.212
1.210
1.150
1.149
1.148
1.147
1.146
1.145
1.144
1.143
1.142
140
120
100
80
MAX5974A/MAX5974C
MAX5974B/MAX5974D
60
-40
-15
10
35
60
85
-40
-15
10
35
60
85
-15
10
35
60
85
TEMPERATURE (°C)
TEMPERATURE (°C)
TEMPERATURE (°C)
SUPPLY CURRENT vs. SUPPLY VOLTAGE
(MAX5974A/MAX5974C)
SUPPLY CURRENT vs. SUPPLY VOLTAGE
(MAX5974B/MAX5974D)
SUPPLY CURRENT
vs. SWITCHING FREQUENCY
10,000
1000
100
10,000
1000
100
2.4
2.0
1.6
1.2
0.8
0.4
0
T
A
= +85°C
T = +85°C
A
T
A
= -40°C
T
= -40°C
A
10
10
0
2
4
6
8
10 12 14 16 18 20
0
2
4
6
8
10 12 14 16 18 20
100 200 300 400 500 600 700 800
SWITCHING FREQUENCY (kHz)
TEMPERATURE (°C)
TEMPERATURE (°C)
6
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
Typical Operating Characteristics (continued)
(V = 12V (for MAX5974A/MAX5974C, bring V up to 17V for startup), V
= V
= V
= V = V
= V
=
DCLMP
IN
IN
CS
CSSC
DITHER/SYNC
FB
FFB
V , V = 2V, NDRV = AUXDRV = SS = COMP = unconnected, R = 34.8kI, R = 25kI, unless otherwise noted.)
GND EN RT DT
SWITCHING FREQUENCY
SOFT-START CHARGING CURRENT
vs. TEMPERATURE
SWITCHING FREQUENCY
vs. TEMPERATURE
vs. R VALUE
RT
1000
100
10
10.06
10.05
10.04
10.03
10.02
10.01
10.00
9.99
252
251
250
249
248
247
246
245
244
9.98
9.97
10
100
-40
-15
10
35
60
85
-40
-40
0
-15
10
35
60
85
R
VALUE (kΩ)
TEMPERATURE (°C)
TEMPERATURE (°C)
RT
MAXIMUM DUTY CYCLE
vs. SWITCHING FREQUENCY
MAXIMUM DUTY CYCLE
vs. TEMPERATURE
FREQUENCY DITHERING
vs. R
DITHER
83
82
81
80
79
78
77
76
75
81.0
80.9
80.8
80.7
80.6
80.5
80.4
80.3
80.2
14
12
10
8
6
4
2
0
0
100 200 300 400 500 600 700 800
SWITCHING FREQUENCY (kHz)
-15
10
35
60
85
300 400 500 600 700 800 900 1000
(kΩ)
TEMPERATURE (°C)
R
DITHER
MAXIMUM DUTY CYCLE
MAXIMUM DUTY CYCLE
MAXIMUM DUTY CYCLE
vs. SYNC FREQUENCY
vs. V
vs. V
SS
DCLMP
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
45
40
35
30
25
20
15
10
5
V
= 0.5V
SS
0
0
0.5
1.0
1.5
(V)
2.0
2.5
0.5
1.0
V
1.5
(V)
2.0
2.5
250
300
350
400
450
500
V
SYNC FREQUENCY (kHz)
SS
DCLMP
7
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
Typical Operating Characteristics (continued)
(V = 12V (for MAX5974A/MAX5974C, bring V up to 17V for startup), V
= V
= V
= V = V
= V
=
DCLMP
IN
IN
CS
CSSC
DITHER/SYNC
FB
FFB
V , V = 2V, NDRV = AUXDRV = SS = COMP = unconnected, R = 34.8kI, R = 25kI, unless otherwise noted.)
GND EN RT DT
PEAK CURRENT-LIMIT THRESHOLD
vs. TEMPERATURE
DEAD TIME vs. TEMPERATURE
DEAD TIME vs. R VALUE
DT
398
397
396
395
394
393
392
391
390
389
388
102
100
98
400
350
300
250
200
150
100
50
96
94
92
90
88
0
-40
-40
-40
-15
10
35
60
85
-40
-15
10
35
60
85
110
10 20 30 40 50 60 70 80 90 100
VALUE (kΩ)
TEMPERATURE (°C)
TEMPERATURE (°C)
R
DT
SLOPE COMPENSATION CURRENT
vs. TEMPERATURE
NDRV MINIMUM ON-TIME
vs. TEMPERATURE
REVERSE CURRENT-LIMIT THRESHOLD
vs. TEMPERATURE
-97
-98
54.0
53.5
53.0
52.5
52.0
51.5
51.0
50.5
50.0
170
165
160
155
150
145
140
-99
-100
-101
-102
-103
-104
-105
-106
-107
-40
-15
10
35
60
85
-40
-15
10
35
60
85
-15
10
35
60
85
TEMPERATURE (°C)
TEMPERATURE (°C)
TEMPERATURE (°C)
FEEDBACK VOLTAGE
vs. TEMPERATURE
CURRENT-SENSE GAIN
vs. TEMPERATURE
FEEDBACK VOLTAGE
vs. TEMPERATURE
3.40
3.39
3.38
3.37
3.36
3.35
3.34
3.33
3.32
3.31
3.30
1.220
1.219
1.218
1.217
1.216
1.215
1.214
1.213
1.212
1.211
1.210
1.522
1.521
1.520
1.519
1.518
1.517
1.516
MAX5974C/MAX5974D
-40
-15
10
35
60
85
-40
-15
10
35
60
85
-15
10
35
60
85
TEMPERATURE (°C)
TEMPERATURE (°C)
TEMPERATURE (°C)
8
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
Typical Operating Characteristics (continued)
(V = 12V (for MAX5974A/MAX5974C, bring V up to 17V for startup), V
= V
= V
= V = V
= V
DCLMP
=
IN
IN
CS
CSSC
DITHER/SYNC
FB
FFB
V , V = 2V, NDRV = AUXDRV = SS = COMP = unconnected, R = 34.8kI, R = 25kI, unless otherwise noted.)
GND EN RT DT
TRANSCONDUCTANCE HISTOGRAM
(MAX5974A/MAX5974B)
TRANSCONDUCTANCE HISTOGRAM
TRANSCONDUCTANCE
vs. TEMPERATURE
(MAX5974C/MAX5974D)
3.0
2.9
2.8
2.7
2.6
2.5
2.4
2.3
2.2
2.1
25
20
15
10
5
25
20
15
10
5
MAX5974C/MAX5974D
MAX5974A/MAX5974B
2.0
-40
0
0
-15
10
35
60
85
2.44 2.46 2.48 2.50 2.52 2.54 2.56 2.58 2.60 2.62 2.64
TRANSCONDUCTANCE (mS)
2.56 2.58 2.60 2.62 2.64 2.66 2.68 2.70 2.72 2.74 2.76
TRANSCONDUCTANCE (mS)
TEMPERATURE (°C)
ENABLE RESPONSE
SHUTDOWN RESPONSE
MAX5974A/B/C/D toc32
MAX5974A/B/C/D toc31
V
EN
V
EN
5V/div
5V/div
V
NDRV
V
NDRV
10V/div
10V/div
V
AUXDRV
V
AUXDRV
10V/div
10V/div
V
OUT
V
OUT
5V/div
5V/div
100µs/div
200µs/div
V
SS
RAMP RESPONSE
V
RAMP RESPONSE
DCLMP
MAX5974A/B/C/D toc33
MAX5974A/B/C/D toc34
V
SS
V
DCLMP
2V/div
2V/div
V
V
NDRV
NDRV
10V/div
10V/div
V
AUXDRV
V
AUXDRV
10V/div
10V/div
10µs/div
10µs/div
9
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
Typical Operating Characteristics (continued)
(V = 12V (for MAX5974A/MAX5974C, bring V up to 17V for startup), V
= V
= V
= V = V
= V
=
DCLMP
IN
IN
CS
CSSC
DITHER/SYNC
FB
FFB
V , V = 2V, NDRV = AUXDRV = SS = COMP = unconnected, R = 34.8kI, R = 25kI, unless otherwise noted.)
GND EN RT DT
NDRV 10% TO 90% RISE TIME
NDRV 90% TO 10% FALL TIME
AUXDRV 10% TO 90% RISE TIME
MAX5974A/B/C/D toc35
MAX5974A/B/C/D toc36
MAX5974A/B/C/D toc37
0ns
27.6ns
45.6ns
V
NDRV
V
NDRV
V
AUXDRV
2V/div
2V/div
2V/div
13.8ns
0ns
0ns
10ns/div
10ns/div
10ns/div
AUXDRV 90% TO 10% FALL TIME
PEAK NDRV CURRENT
MAX5974A/B/C/D toc38
MAX5974A/B/C/D toc39
PEAK SOURCE CURRENT
0ns
V
I
AUXDRV
2V/div
NDRV
0.5A/div
21ns
PEAK SINK CURRENT
10ns/div
200ns/div
PEAK AUXDRV CURRENT
SHORT-CURRENT BEHAVIOR
MAX5974A/B/C/D toc40
MAX5974A/B/C/D toc41
15V
5V
V
PEAK SOURCE
CURRENT
IN
5V/div
I
AUXDRV
V
NDRV
0.2A/div
10V/div
V
CS
500mV/div
PEAK SINK CURRENT
400ns/div
40ms/div
10
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
Pin Configuration
TOP VIEW
12
11
10
9
CSSC
GND
FB
13
14
IN
8
7
6
5
MAX5974A
MAX5974B
MAX5974C
MAX5974D
EN
DCLMP 15
16
EP
COMP
SS
+
1
2
3
4
THIN QFN
Pin Description
PIN
NAME
FUNCTION
Dead-Time Programming Resistor Connection. Connect resistor R from DT to GND to set the
DT
1
DT
desired dead time between the NDRV and AUXDRV signals. See the Dead Time section to calculate
the resistor value for a particular dead time.
Frequency Dithering Programming or Synchronization Connection. For spread-spectrum frequency
operation, connect a capacitor from DITHER to GND and a resistor from DITHER to RT. To
synchronize the internal oscillator to the externally applied frequency, connect DITHER/SYNC to the
synchronization pulse.
DITHER/
SYNC
2
3
Switching Frequency Programming Resistor Connection. Connect resistor R from RT to GND to
RT
set the PWM switching frequency. See the Oscillator/Switching Frequency section to calculate the
RT
resistor value for the desired oscillator frequency.
Frequency Foldback Threshold Programming Input. Connect a resistor from FFB to GND to set the
output average current threshold below which the converter folds back the switching frequency to
1/2 of its original value. Connect to GND to disable frequency foldback.
4
5
FFB
Transconductance Amplifier Output and PWM Comparator Input. COMP is level shifted down and
connected to the inverting input of the PWM comparator.
COMP
11
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
Pin Description (continued)
PIN
6
NAME
FB
FUNCTION
Transconductance Amplifier Inverting Input
Signal Ground
7
GND
Current Sense with Slope Compensation Input. A resistor connected from CSSC to CS programs the
amount of slope compensation. See the Programmable Slope Compensation section.
8
9
CSSC
CS
Current-Sense Input. Current-sense connection for average current sense and cycle-by-cycle
current limit. Peak current-limit trip voltage is 400mV and reverse current-limit trip voltage is -100mV.
10
11
PGND
NDRV
Power Ground. PGND is the return path for gate-driver switching currents.
Main Switch Gate-Driver Output
pMOS Active Clamp Switch Gate-Driver Output. AUXDRV can also be used to drive a pulse
transformer for synchronous flyback application.
12
13
AUXDRV
IN
Converter Supply Input. IN has wide UVLO hysteresis, enabling the design of efficient power
supplies. See the Enable Input section to determine if an external zener diode is required at IN.
Enable Input. The gate drivers are disabled and the device is in a low-power UVLO mode when the
14
15
EN
voltage on EN is below V
enable conditions. See the Enable Input section for more information about interfacing to EN.
. When the voltage on EN is above V
, the device checks for other
ENF
ENR
Feed-Forward Maximum Duty-Cycle Clamp Programming Input. Connect a resistive divider between
the input supply voltage DCLMP and GND. The voltage at DCLMP sets the maximum duty cycle
DCLMP
(D ) of the converter inversely proportional to the input supply voltage, so that the MOSFET
MAX
remains protected during line transients.
Soft-Start Programming Capacitor Connection. Connect a capacitor from SS to GND to program the
soft-start period. This capacitor also determines hiccup mode current-limit restart time. A resistor
16
—
SS
EP
from SS to GND can also be used to set the D
below 75%.
MAX
Exposed Pad. Internally connected to GND. Connect to a large ground plane to maximize thermal
performance. Not intended as an electrical connection point.
12
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
Block Diagrams
13
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
Block Diagrams (continued)
14
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
The devices include a cycle-by-cycle current limit
Detailed Description
that turns off the main and AUX drivers whenever the
internally set threshold of 400mV is exceeded. Eight
consecutive occurrences of current-limit events trigger
hiccup mode, which protects external components by
The MAX5974A/MAX5974B/MAX5974C/MAX5974D are
optimized for controlling a 25W to 50W active-clamped,
self-driven synchronous rectification forward converter
in continuous-conduction mode. The main switch gate
driver (NDRV) and the active-clamped switch driver
(AUXDRV) are sized to optimize efficiency for 25W
design. The features-rich devices are ideal for PoE IEEE
802.3af/at-powered devices.
halting switching for a period of time (t ) and allow-
RSTRT
ing the overload current to dissipate in the load and
body diode of the synchronous rectifier before soft-start
is reattempted.
The reverse current-limit feature of the devices turns
the AUX driver off for the remaining off period when
The MAX5974A/MAX5974C offer a 16V bootstrap UVLO
wake-up level with a 9V wide hysteresis. The low startup
and operating currents allow the use of a smaller storage
capacitor at the input without compromising startup and
hold times. The MAX5974A/MAX5974C are well-suited
for universal input (rectified 85V AC to 265V AC) or tele-
com (-36V DC to -72V DC) power supplies.
V
CS
exceeds the -100mV threshold. This protects the
transformer core from saturation due to excess reverse
current under some extreme transient conditions.
Current-Mode Control Loop
The advantages of current-mode control over voltage-
mode control are twofold. First, there is the feed-forward
characteristic brought on by the controller’s ability to adjust
for variations in the input voltage on a cycle-by-cycle basis.
Second, the stability requirements of the current-mode
controller are reduced to that of a single-pole system,
unlike the double pole in voltage-mode control.
The MAX5974B/MAX5974D have a UVLO rising threshold
of 8.4V and can accommodate for low-input voltage (12V
DC to 24V DC) power sources such as wall adapters.
Power supplies designed with the MAX5974A/MAX5974C
use a high-value startup resistor, R , that charges a
IN
reservoir capacitor, C (see the Typical Application
IN
The devices use a current-mode control loop where the
scaled output of the error amplifier (COMP) is compared
to a slope-compensated current-sense signal at CSSC.
Circuits). During this initial period, while the voltage is
less than the internal bootstrap UVLO threshold, the
device typically consumes only 100FA of quiescent cur-
rent. This low startup current and the large bootstrap
UVLO hysteresis help to minimize the power dissipation
Input Clamp
When the device is enabled, an internal 18V input clamp
is active. During an overvoltage condition, the clamp
prevents the voltage at the supply input IN from rising
above 18.5V (typ).
across R even at the high end of the universal AC input
IN
voltage (265V AC).
Feed-forward maximum duty-cycle clamping detects chang-
es in line conditions and adjusts the maximum duty cycle
accordingly to eliminate the clamp voltage’s (i.e., the main
power FET’s drain voltage) dependence on the input voltage.
When the device is disabled, the input clamp circuitry is
also disabled.
Enable Input
The enable input is used to enable or disable the device.
Driving EN low disables the device. Note that the inter-
nal 18V input clamp is also disabled when EN is low.
Therefore, an external 18V zener diode is needed for
certain operating conditions as described below.
For EMI-sensitive applications, the programmable fre-
quency dithering feature allows up to Q10% variation in
the switching frequency. This spread-spectrum modula-
tion technique spreads the energy of switching harmon-
ics over a wider band while reducing their peaks, help-
ing to meet stringent EMI goals.
15
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
UVLO on Power Source
The enable input has an accurate threshold of 1.26V
(max). For applications that require a UVLO on the
power source, connect a resistive divider from the power
source to EN to GND as shown in Figure 1. A zener
diode between IN and PGND is required to prevent the
NDRV and AUXDRV gate-drive voltages from exceeding
20V, the maximum allowed gate voltage of power FETs.
UVLO threshold for the power source, below which the
device is disabled.
The digital output connected to EN should be capable
of withstanding more than the maximum supply voltage.
MCU Control of Enable Input
When using a microcontroller GPIO to control the enable
input, an 18V zener diode is required on IN as shown in
Figure 2.
The external zener diode should clamp in the following
range:
High-Voltage Logic Control of Enable Input
In the case where EN is externally controlled by a high-
voltage open-drain/collector output (e.g., PGOOD indi-
cator of a powered device controller), connect IN to EN
20V > V > V
Z
UVLO(MAX)
through a resistor R and connect EN to an open-drain
where V is the zener voltage and V
is the
UVLO(MAX)
EN
Z
or open-collector output as shown in Figure 3. Select
maximum wakeup level (16.5V or 8.85V depending on
the device version). An 18V zener diode is the best
choice.
R
EN
such that the voltage at IN, when EN is low, is less
than 20V (i.e., the maximum gate voltage of the main and
AUX FETs):
Design the resistive divider by first selecting the value of
R
to be on the order of 100kω. Then calculate R
EN1
EN2
R
EN
+ R
as follows:
V
×
< 20V
S(MAX)
R
EN
IN
V
EN(MAX)
V
= R
×
EN1
EN2
where V
is the maximum supply voltage. Obeying
this relationship eliminates the need for an external zener
diode.
_
V
V
EN(MAX)
S(MAX)
S(UVLO)
where V
is the maximum enable threshold volt-
EN(MAX)
The digital output connected to EN should be capable of
withstanding more than 20V.
age and is equal to 1.26V and V
is the desired
S(UVLO)
V
S
V
S
R
IN
R
IN
IN
IN
18V
C
IN
18V
C
IN
MAX5974
R
EN1
MAX5974_
MCU
DIGITAL
I/O
CONTROL
EN
EN
R
N
EN2
Figure 1. Programmable UVLO for the Power Source
Figure 2. MCU Control of the Enable Input
16
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
Because the MAX5974B/MAX5974D are designed for
use with low-voltage power sources such as wall adapt-
ers outputting 12V to 24V, they have a lower UVLO
wake-up threshold of 8.4V.
V
S
R
IN
Startup Operation
The device starts up when the voltage at IN exceeds 16V
(MAX5974A/MAX5974C) or 8.4V (MAX5974B/MAX5974D)
IN
C
IN
and the enable input voltage is greater than 1.26V.
During normal operation, the voltage at IN is nor-
mally derived from a tertiary winding of the transformer
R
EN
MAX5974
(MAX5974C/MAX5974D). However, at startup there is
no energy being delivered through the transformer;
hence, a special bootstrap sequence is required. In the
DIGITAL
CONTROL
EN
Typical Application Circuits, C charges through the
IN
N
startup resistor, R , to an intermediate voltage. Only
IN
100FA of the current supplied through R is used by
IN
the ICs, the remaining input current charges C until
IN
V
V
reaches the bootstrap UVLO wake-up level. Once
exceeds this level, NDRV begins switching the
IN
IN
Figure 3. High-Voltage Logic Control of the Enable Input
n-channel MOSFET and transfers energy to the second-
ary and tertiary outputs. If the voltage on the tertiary
output builds to higher than 7V (the bootstrap UVLO
shutdown level), then startup has been accomplished
V
S
and sustained operation commences. If V drops below
IN
7V before startup is complete, the device goes back to
R
IN
low-current UVLO. In this case, increase the value of C
IN
in order to store enough energy to allow for the voltage
at the tertiary winding to build up.
IN
While the MAX5974A/MAX5974B derive their input volt-
age from the coupled inductor output during normal
operation, the startup behavior is similar to that of the
MAX5974C/MAX5974D.
C
IN
MAX5974_
EN
Soft-Start
A capacitor from SS to GND, C , programs the soft-
SS
start time. V controls the oscillator duty cycle during
SS
startup to provide a slow and smooth increase of the
duty cycle to its steady-state value. Calculate the value
Figure 4. Always-On Operation
of C as follows:
SS
Always-On Operation
For always-on operation, connect EN to IN as shown
in Figure 4. No external zener diode is needed for this
configuration.
I
× t
2V
SS-CH SS
C
=
SS
Bootstrap Undervoltage Lockout
The devices have an internal bootstrap UVLO that is very
useful when designing high-voltage power supplies (see
the Block Diagrams). This allows the device to bootstrap
itself during initial power-up. The MAX5974A/MAX5974C
where I
(10FA typ) is the current charging C dur-
SS
SS-CH
ing soft-start and t is the programmed soft-start time.
SS
A resistor can also be added from the SS pin to GND to
clamp V < 2V and, hence, program the maximum duty
cycle to be less than 80% (see the Duty-Cycle Clamping
section).
SS
soft-start when V exceeds the bootstrap UVLO thresh-
IN
old of V
(16V typ).
INUVR
17
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
n-Channel MOSFET Gate Driver
Dead Time
The NDRV output drives an external n-channel MOSFET.
NDRV can source/sink in excess of 650mA/1000mA
peak current; therefore, select a MOSFET that yields
acceptable conduction and switching losses. The exter-
nal MOSFET used must be able to withstand the maxi-
mum clamp voltage.
Dead time between the main and AUX output edges allow
ZVS to occur, minimizing conduction losses and improv-
ing efficiency. The dead time (t ) is applied to both
DT
leading and trailing edges of the main and AUX outputs
as shown in Figure 5. Connect a resistor between DT and
GND to set t to any value between 40ns and 400ns:
DT
p-Channel MOSFET Gate Driver
The AUXDRV output drives an external p-channel
MOSFET with the aid of a level shifter. The level shifter
10kΩ
40ns
R
=
× t
DT
DT
consists of C
Application Circuits. When AUXDRV is high, C
recharged through D5. When AUXDRV is low, the gate
of the p-channel MOSFET is pulled below the source by
, R
, and D5 as shown in the Typical
AUX AUX
Oscillator/Switching Frequency
is
AUX
The ICs’ switching frequency is programmable between
100kHz and 600kHz with a resistor R
connected
RT
between RT and GND. Use the following formula to
determine the appropriate value of R needed to gen-
the voltage stored on C
, turning on the pFET.
AUX
RT
Add a zener diode between gate to source of the exter-
nal n-channel and p-channel MOSFETs after the gate
erate the desired output-switching frequency (f ):
SW
resistors to protect V
maximum rating during transient condition (see the
Typical Application Circuits).
from rising above its absolute
GS
9
8.7 ×10
R
=
RT
f
SW
where f
is the desired switching frequency.
SW
BLANKING, t
BLK
NDRV
AUXDRV
DEAD TIME, t
DT
Figure 5. Dead Time Between AUXDRV and NDRV
18
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
400mV. The duty cycle is terminated immediately when
exceeds 400mV.
Peak Current Limit
The current-sense resistor (R in the Typical
V
CS
CS
Application Circuits), connected between the source
of the n-channel MOSFET and PGND, sets the current
limit. The current-limit comparator has a voltage trip level
Reverse Current Limit
The devices protect the transformer against saturation
due to reverse current by monitoring the voltage across
(V ) of 400mV. Use the following equation to cal-
CS-PEAK
R
is on.
while the AUX output is low and the p-channel FET
CS
culate the value of R
:
CS
Output Short-Circuit Protection
with Hiccup Mode
When the device detects eight consecutive peak current-
limit events, both NDRV and AUXDRV driver outputs are
400mV
R
=
CS
I
PRI
where I
is the peak current in the primary side of
PRI
turned off for a restart period, t . After t , the
RSTRT RSTRT
the transformer, which also flows through the MOSFET.
When the voltage produced by this current (through the
current-sense resistor) exceeds the current-limit com-
parator threshold, the MOSFET driver (NDRV) terminates
the current on-cycle, within 35ns (typ).
device undergoes soft-start. The duration of the restart
period depends on the value of the capacitor at SS (C ).
SS
During this period, C is discharged with a pulldown cur-
SS
rent of I
(2FA typ). Once its voltage reaches 0.15V,
the restart period ends and the device initiates a soft-start
sequence. An internal counter ensures that the minimum
SS-DH
The devices implement 115ns of leading-edge blanking
to ignore leading-edge current spikes. These spikes
are caused by reflected secondary currents, current-
discharging capacitance at the FET’s drain, and gate-
charging current. Use a small RC network for additional
filtering of the leading-edge spike on the sense wave-
form when needed. Set the corner frequency between
10MHz and 20MHz.
restart period (t
) is 1024 clock cycles when the
RSTRT-MIN
time required for C to discharge to 0.15V is less than
SS
1024 clock cycles. Figure 6 shows the behavior of the
device prior and during hiccup mode.
Frequency Foldback for High-Efficiency
Light-Load Operation
The frequency foldback threshold can be programmed
from 0 to 20% of the full load current using a resistor from
FFB to GND.
After the leading-edge blanking time, the device moni-
tors V
for any breaches of the peak current limit of
CS
V
CS-PEAK
(400mV)
V
CSBL
(BLANKED CS
VOLTAGE)
HICCUP
DISCHARGE WITH I
SS-DH
V
SS-HI
SOFT-START
VOLTAGE,
V
SS-DTH
V
SS
t
SS
t
RSTRT
Figure 6. Hiccup Mode Timing Diagram
19
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
When V
falls below V
, the device folds back
FFB
Oscillator Synchronization
The internal oscillator can be synchronized to an external
clock by applying the clock to DITHER/SYNC directly. The
external clock frequency can be set anywhere between
1.1x to 2x the internal clock frequency.
CSAVG
the switching frequency to 1/2 the original value to
reduce switching losses and increase the converter effi-
ciency. Calculate the value of R
as follows:
FFB
10 ×I
×R
CS
LOAD(LIGHT)
Using an external clock increases the maximum duty
R
=
FFB
I
cycle by a factor equal to f /f . This factor should
SYNC SW
FFB
be accounted for in setting the maximum duty cycle
using any of the methods described in the Duty-Cycle
Clamping section. The formula below shows how the
maximum duty cycle is affected by the external clock
frequency:
where R
is the resistor between FFB and GND,
is the current at light-load conditions that
FFB
I
LOAD(LIGHT)
triggers frequency foldback, R
is the value of the
CS
sense resistor connected between CS and PGND, and
is the current sourced from FFB to R (30FA typ).
I
FFB
FFB
V
f
SYNC
MIN
Duty-Cycle Clamping
The maximum duty cycle is determined by the lowest
of three voltages: 2V, the voltage at SS (V ), and the
D
=
×
MAX
2.43V
f
SW
SS
where V
section, f
is described in the Duty-Cycle Clamping
is the switching frequency as set by the
resistor connected between RT and GND, and f
MIN
SW
voltage (2.43V - V ). The maximum duty cycle is
DCLMP
calculated as:
is
SYNC
V
MIN
D
=
the external clock frequency.
MAX
2.43V
Frequency Dithering for Spread-
Spectrum Applications (Low EMI)
The switching frequency of the converter can be dith-
ered in a range of Q10% by connecting a capaci-
tor from DITHER/SYNC to GND, and a resistor from
DITHER/SYNC to RT as shown in the Typical Application
Circuits. This results in lower EMI.
where V
= minimum (2V, V , 2.43V - V
).
MIN
SS
DCLMP
SS
By connecting a resistor between SS and ground, the
voltage at SS can be made to be lower than 2V. V is
SS
calculated as follows:
V
= R ×I
SS SS-CH
SS
A current source at DITHER/SYNC charges the capaci-
tor C
it discharges C
and discharging of the capacitor generates a triangular
waveform on DITHER/SYNC with peak levels at 0.4V and
2V and a frequency that is equal to:
to 2V at 50FA. Upon reaching this trip point,
DITHER
where R
GND, and I
(10FA typ).
is the resistor connected between SS and
SS
to 0.4V at 50FA. The charging
DITHER
is the current sourced from SS to R
SS
SS-CH
DCLMP
using supply voltage feed-forward, connect
To set D
MAX
50µA
a resistive divider between the supply voltage, DCLMP,
and GND as shown in the Typical Application Circuits.
This feed-forward duty-cycle clamp ensures that the
external n-channel MOSFET is not stressed during sup-
f
=
TRI
C
× 3.2V
DITHER
Typically, f
should be set close to 1kHz. The resistor
TRI
ply transients. V
is calculated as follows:
DCLMP
R
connected from DITHER/SYNC to RT deter-
DITHER
mines the amount of dither as follows:
R
DCLMP2
V
=
× V
S
DCLMP
R
+ R
R
4
3
DCLMP1
DCLMP2
RT
DITHER
%DITHER =
×
R
where R
and R
are the resistive divider
DCLMP2
DCLMP1
values shown in the Typical Application Circuits and V
is the input supply voltage.
S
where %DITHER is the amount of dither expressed as a
percentage of the switching frequency. Setting R
DITHER
to 10 x R generates Q10% dither.
RT
20
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
Programmable Slope Compensation
Applications Information
The device generates a current ramp at CSSC such that
its peak is 50FA at 80% duty cycle of the oscillator. An
external resistor connected from CSSC to the CS then
converts this current ramp into programmable slope-
compensation amplitude, which is added to the current-
sense signal for stability of the peak current-mode
control loop. The ramp rate of the slope compensation
signal is given by:
Startup Time Considerations
The bypass capacitor at IN, C , supplies current
IN
immediately after the devices wake up (see the Typical
Application Circuits). Large values of C
increase
IN
the startup time, but also supply gate charge for more
cycles during initial startup. If the value of C is too
IN
small, V drops below 7V because NDRV does not have
IN
enough time to switch and build up sufficient voltage
across the tertiary output (MAX5974C/MAX5974D) or
coupled inductor output (MAX5974A/MAX5974B), which
powers the device. The device goes back into UVLO
R
× 50µA × f
CSSC
SW
m =
80%
and does not start. Use a low-leakage capacitor for C .
IN
where m is the ramp rate of the slope-compensation
signal, R is the value of the resistor connected
Typically, offline power supplies keep startup times to
less than 500ms even in low-line conditions (85V AC
input for universal offline or 36V DC for telecom applica-
CSSC
between CSSC and CS used to program the ramp rate,
and f is the switching frequency.
SW
tions). Size the startup resistor, R , to supply both the
IN
Error Amplifier
maximum startup bias of the device (150FA) and the
The MAX5974A/MAX5974B include an internal error
amplifier with a sample-and-hold input. The feedback
input of the MAX5974C/MAX5974D is continuously con-
nected. The noninverting input of the error amplifier is
connected to the internal reference and feedback is
provided at the inverting input. High open-loop gain and
unity-gain bandwidth allow good closed-loop bandwidth
and transient response. Calculate the power-supply out-
put voltage using the following equation:
charging current for C . C must be charged to 16V
IN
IN
within the desired 500ms time period. C must store
IN
enough charge to deliver current to the device for at
least the soft-start time (t ) set by C . To calculate the
SS
SS
approximate amount of capacitance required, use the
following formula:
I
= Q
f
GTOT SW
G
(I +I )(t
)
IN
G
SS
C
=
IN
V
HYST
R
+ R
FB1
R
FB2
V
= V
×
OUT
REF
FB2
where I is the ICs’ internal supply current (1.8mA)
IN
after startup, Q
n-channel and p-channel FETs, f
ing frequency, V
is the total gate charge for the
GTOT
where V
= 1.52V for the MAX5974A/MAX5974B
= 1.215V for the MAX5974C/MAX5974D. The
REF
is the ICs’ switch-
SW
and V
REF
is the bootstrap UVLO hysteresis
HYST
amplifier’s noninverting input is internally connected to
a soft-start circuit that gradually increases the reference
voltage during startup. This forces the output voltage to
come up in an orderly and well-defined manner under
all load conditions.
(9V typ), and t is the soft-start time. R is then cal-
SS
IN
culated as follows:
V
− V
S(MIN)
INUVR
R
≅
IN
I
START
where V
is the minimum input supply voltage for
S(MIN)
the application (36V for telecom), V
is the boot-
INUVR
strap UVLO wake-up level (16V), and I
is the IN
START
supply current at startup (150FA max).
21
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
Choose a higher value for R than the one calculated
IN
above if a longer startup time can be tolerated in order
to minimize power loss on this resistor.
The AUX driver controls the p-channel FET through a
level shifter. The level shifter consists of an RC network
(formed by C
and R ) and diode D5, as shown in
AUX
AUX
the Typical Application Circuits. Choose R
and C
AUX
AUX
Active Clamp Circuit
so that the time constant exceeds 100/f . Diode D5 is a
SW
Traditional clamp circuits prevent transformer saturation
small-signal diode with a voltage rating exceeding 25V.
by channeling the magnetizing current (I ) of the trans-
M
Additionally, C
should be chosen such that the
CLAMP
former onto a dissipative RC network. To improve effi-
complex poles formed with magnetizing inductance
ciency, the active clamp circuit recycles I between the
M
(L
MAG
) and C
are 2x to 4x away from the loop
CLAMP
magnetizing inductance and clamp capacitor. V
is given by:
CLAMP
bandwidth:
1-D
V
S
1− D
> 3 × f
BW
V
=
CLAMP
2π L
× C
CLAMP
MAG
where V is the voltage of the power source and D is
S
Bias Circuit
the duty cycle. To select n-channel and p-channel FETs
with adequate breakdown voltages, use the maximum
Optocoupler Feedback (MAX5974C/MAX5974D)
An in-phase tertiary winding is needed to power the bias
circuit when using optocoupler feedback. The voltage
value of V
. V
occurs when the input
CLAMP CLAMP(MAX)
voltage is at its minimum and the duty cycle is at its
maximum. V during normal opera-
across the tertiary V during the on-time is:
T
CLAMP(MAX-NORMAL)
tion is therefore:
N
N
T
S
V
= V
×
T
OUT
V
S(MIN)
V
=
CLAMP(MAX-NORMAL)
N
× V
P
O
where V
is the output voltage and N /N is the turns
OUT T S
1− N × V
ratio from the tertiary to the secondary winding. Select the
turns ratio so that V is above the UVLO shutdown level
S
S(MIN)
T
(7.35V max) by a margin determined by the holdup time
needed to “ride through” a brownout.
where V
is the minimum voltage of the power
S(MIN)
source, N /N is the primary to secondary turns ratio,
P
S
and V is the output voltage. The clamp capacitor,
n-channel, and p-channel FETs must have breakdown
voltages exceeding this level.
O
Coupled-Inductor Feedback (MAX5974A/MAX5974B)
When using coupled-inductor feedback, the power for
the devices can be taken from the coupled inductor dur-
ing the off-time. The voltage across the coupled induc-
If feed-forward maximum duty-cycle clamp is used then:
tor, V , during the off-time is:
COUPLED
V
V
DCLMP
2.43
MIN
D
=
×
= 1−
MAX-FF
N
N
C
O
2.43
V
= V
×
COUPLED
OUT
V
R
DCLMP2
S
= 1−
2.43
R
+ R
DCLMP1 DCLMP2
where V
is the output voltage and N /N is the
C O
OUT
turns ratio from the coupled output to the main output
winding. Select the turns ratio so that V is
above the UVLO shutdown level (7.5V max) by a margin
determined by the holdup time needed to “ride through”
a brownout.
Therefore, V
mum duty clamp is:
during feed-forward maxi-
CLAMP(MAX-FF)
COUPLED
V
S
V
=
CLAMP(MAX-FF)
1− D
+ R
MAX−FF
This voltage appears at the input of the devices, less
2.43 × R
a diode drop. An RC network consisting of R
and
(
)
SNUB
DCLMP1
DCLMP2
=
C
SNUB
is for damping the reverse recovery transients of
R
DCLMP2
diode D6.
22
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
During on-time, the coupled output is:
Layout Recommendations
Typically, there are two sources of noise emission in a
switching power supply: high di/dt loops and high dV/dt
surfaces. For example, traces that carry the drain current
often form high di/dt loops. Similarly, the heatsink of the
main MOSFET presents a dV/dt source; therefore, mini-
mize the surface area of the MOSFET heatsink as much
as possible. Keep all PCB traces carrying switching cur-
rents as short as possible to minimize current loops. Use
a ground plane for best results.
N
N
N
N
S
P
C
O
V
= −(V ×
− V )
OUT
COUPLED-ON
S
where V is the input supply voltage.
S
Care must be taken to ensure that the voltage at FB
(equal to V attenuated by the feedback
COUPLED-ON
resistive divider) is not more than 5V:
For universal AC input design, follow all applicable
safety regulations. Offline power supplies can require
UL, VDE, and other similar agency approvals.
R
FB2
V
= V
×
< 5V
FB-ON
COUPLED-ON
R
(
+ R
)
FB1
FB2
Refer to the MAX5974A and MAX5974C Evaluation Kit
data sheets for recommended layout and component
values.
If this condition is not met, a signal diode should be
placed from GND (anode) to FB (cathode).
23
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
Typical Application Circuits
V
S
L1
3.3mH
36V TO 57V
D1
C
BULK
33µF
N
T
R
IN
100kI
D2
L2
C
IN
6.8µH
1µF
25V
5V, 5A
R
FB1
D3
GATE1
10I
R
10I
C
OUT5
0.1µF
GATE2
7.5kI
1%
C
C
C
C
OUT1 OUT2 OUT3 OUT4
T1
R
N
P
N
S
RDCLMP1
IN
N2
5i412DP
30.1kI
N
R
FB2
1%
R
EN
100kI
2.49kI
1%
D4
PGOOD
EN
RDCLMP2
750I 1%
N
DCLMP
N1
C
SS
0.1µF
5i412DP
SS
DT
MAX5974C
MAX5974D
IN
R
DT
16.9kI 1%
N3
FDS3692
R
OPTO3
R
4.99kI
OPTO1
825I
1%
(OPTOCOUPLER
FEEDBACK)
C
COMP1
2.2nF
C
CLAMP
47nF
R
10I
1%
C
GATE3
DITHER
10nF
R
COMP2
499I
1%
DITHER/
SYNC
U1
FOD817CSD
NDRV
N
R
10I
GATE4
R
RT
14.7kI 1%
C
COMP2
6.8pF
N4
IRF6217
P
AUXDRV
RT
R
BIAS
C
47nF
AUX
4.02kI
1%
R
FFB
10.0kI 1%
R
F
C
INT
0.1µF
499I 1%
FFB
FB
CS
C
330pF
F
R
COMP2
R
R
G2
G1
121kI 1% 200kI 1%
2.00kI
R
AUX
10kI
D5
1%
COMP
CSSC
R
CSSC
4.02kI 1%
GND
PGND
U2
TLV4314AIDBVT-1.24V
R
OPTO2
1kI
R
CS
0.2I
1%
24
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
Typical Application Circuits (continued)
D6
R
FB1
54.9kI1%
C
R
SNUB
SNUB
V
S
10pF 69.8I1%
36V TO 57V
TO FB
R
FB2
C
33µF
63V
BULK
10kI 1%
R
IN
100kI
L
COUPLED
N
C
4 x 47µF
6.3V
C
1µF
25V
IN
5V, 5A
OUT5
N
O
R
10I
R
D3
GATE2
DCLMP1
T1
30.1kI
C
C
C
C
OUT1 OUT2 OUT3 OUT4
R
GATE1
10I
N
P
N
S
C
1%
0.1µF
N2
5i412DP
N
IN
R
EN
100kI
D4
PGOOD
EN
N
RDCLMP2
750I 1%
DCLMP
N1
5i412DP
C
SS
0.1µF
SS
DT
MAX5974A
MAX5974B
R
DT
16.9kI 1%
N3
FDS3692
C
47nF
CLAMP
(COUPLED INDUCTOR
FEEDBACK)
R
10I
C
GATE3
DITHER
10nF
DITHER/
SYNC
NDRV
N
R
10I
GATE4
R
RT
14.7kI 1%
N4
IRF6217
P
AUXDRV
RT
C
47nF
AUX
R
FFB
10kI 1%
R
F
FFB
499I 1%
CS
C
330pF
F
FB
C
COMP
4.7nF
R
Z
R
AUX
D5
2kI 1%
10kI
COMP
CSSC
R
CSSC
4.02kI 1%
GND
PGND
C
INT
47nF
R
0.2I
CS
25
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
Typical Application Circuits (continued)
L1
D1
V
S
N
T
C
D2
BULK
R
IN
L2
C
IN
T1
D3
GATE1
R
R
R
FB1
FB2
GATE2
C
C
OUT2
C
C
OUT3 OUT4
N
P
N
S
OUT1
R
N
IN
N2
R
DCLMP1
R
EN
100kI
D4
PGOOD
N
EN
R
DCLMP2
N1
DCLMP
C
SS
SS
DT
MAX5974C
MAX5974D
R
DT
R
C
CLAMP
DITHER
R
GATE3
C
DITHER
NDRV
DITHER/
SYNC
N
N3
R
GATE4
R
RT
P
N4
AUXDRV
RT
C
AUX
R
FFB
FFB
CS
CSSC
FB
D5
R
AUX
R
CSSC
COMP
R
z
GND
PGND
R
CS
C
COMP
C
HF
Chip Information
Package Information
For the latest package outline information and land patterns
(footprints), go to www.maxim-ic.com/packages. Note that a
“+”, “#”, or “-” in the package code indicates RoHS status only.
Package drawings may show a different suffix character, but
the drawing pertains to the package regardless of RoHS status.
PROCESS: BiCMOS
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE
NO.
LAND
PATTERN NO.
16 TQFN-EP
T1633+4
21-0136
90-0031
26
Active-Clamped, Spread-Spectrum,
Current-Mode PWM Controllers
Revision History
REVISION
NUMBER
REVISION
DATE
PAGES
DESCRIPTION
CHANGED
0
1
2
6/10
9/10
6/11
Initial release
—
Introduced the MAX5974B/MAX5974D. Updated the Absolute Maximum
Ratings, Electrical Characteristics, Pin Description, the p-Channel MOSFET
Gate Driver, Frequency Foldback for High-Efficiency Light-Load Operation
sections, and Typical Application Circuits.
1, 2, 3, 12, 15, 17,
19, 21, 23, 24, 25
Added internal zener diode information
1–10, 12–17, 19–25
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied.
Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
27
©
2011 Maxim Integrated Products
Maxim is a registered trademark of Maxim Integrated Products, Inc.
相关型号:
![](http://pdffile.icpdf.com/pdf1/p00178/img/page/MAX59_1003566_files/MAX59_1003566_1.jpg)
![](http://pdffile.icpdf.com/pdf1/p00178/img/page/MAX59_1003566_files/MAX59_1003566_2.jpg)
MAX5974DETE+T
Switching Controller, Current-mode, 600kHz Switching Freq-Max, BICMOS, 3 X 3 MM, ROHS COMPLIANT, TQFN-16
MAXIM
![](http://pdffile.icpdf.com/pdf2/p00357/img/page/MAX5975A_2191252_files/MAX5975A_2191252_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00357/img/page/MAX5975A_2191252_files/MAX5975A_2191252_2.jpg)
MAX5975A
Current-Mode PWM Controllers with Frequency Dithering for EMI-Sensitive Power Supplies
MAXIM
![](http://pdffile.icpdf.com/pdf2/p00239/img/page/MAX5975AETE-_1444347_files/MAX5975AETE-_1444347_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00239/img/page/MAX5975AETE-_1444347_files/MAX5975AETE-_1444347_2.jpg)
MAX5975AETE+
Switching Controller, Current-mode, 600kHz Switching Freq-Max, BICMOS, 3 X 3 MM, ROHS COMPLIANT, TQFN-16
MAXIM
![](http://pdffile.icpdf.com/pdf2/p00357/img/page/MAX5975A_2191252_files/MAX5975A_2191252_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00357/img/page/MAX5975A_2191252_files/MAX5975A_2191252_2.jpg)
MAX5975B
Current-Mode PWM Controllers with Frequency Dithering for EMI-Sensitive Power Supplies
MAXIM
![](http://pdffile.icpdf.com/pdf2/p00357/img/page/MAX5975A_2191252_files/MAX5975A_2191252_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00357/img/page/MAX5975A_2191252_files/MAX5975A_2191252_2.jpg)
MAX5975BETE+
Current-Mode PWM Controllers with Frequency Dithering for EMI-Sensitive Power Supplies
MAXIM
©2020 ICPDF网 联系我们和版权申明