MAX8709BETI+ [MAXIM]
Fluorescent Light Controller, 0.5A, BICMOS, 5 X 5 MM, 0.80 MM, TQFN-28;
| 型号： | MAX8709BETI+ |
| 厂家： | 
MAXIM INTEGRATED PRODUCTS |
| 描述： | Fluorescent Light Controller, 0.5A, BICMOS, 5 X 5 MM, 0.80 MM, TQFN-28 信息通信管理 |
| 文件： | 总24页 (文件大小：1801K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MAX8709B
High-Efficiency CCFL Backlight
Controller with SMBus Interface
General Description
Features
● Synchronized to Resonant Frequency
The MAX8709B integrated backlight controller is opti-
mized to drive cold-cathode fluorescent lamps (CCFLs)
using a resonant full-bridge inverter architecture. The
resonant operation maximizes striking capability and
provides near-sinusoidal waveforms over the entire input
range to improve CCFL lifetime. The controller operates
over a wide input voltage range of 4.6V to 28V with high
power-to-light efficiency. The device also includes safety-
features that effectively protect against many single-point-
fault conditions including lamp-out and short-circuit faults.
Longer Lamp Life
Guaranteed Striking Capability
High Power-to-Light Efficiency
● Wide Input Voltage Range (4.6V to 28V)
● Feed Forward for Excellent Line Rejection
● SMBus Dimming Control Interface
● 10:1 Dimming Range
● Guaranteed 200Hz to 220Hz DPWM Frequency
The MAX8709B achieves 10:1 dimming range by “chop-
ping” the lamp current on and off using a digital pulse-
width-modulation (DPWM) method. The minimum DPWM
duty cycle of the MAX8709B is 12.5%. The brightness is
controlled with a 2-wire SMBus-compatible interface. The
device directly drives the four external N-channel power
MOSFETs of the full-bridge inverter. An internal 5.3V linear
regulator powers the MOSFET drivers, the DPWM oscil-
lator, and most of the internal circuitry. The MAX8709B is
available in a space-saving 28-pin thin QFN package and
operates over a -40°C to +85°C temperature range.
● Secondary Voltage Limit Reduces Transformer
Stress
● Adjustable Lamp-Out Protection with 1s Timer
● Secondary Current Limit Protects Against High-
Voltage Short Circuits to Ground
● Small, 5mm x 5mm, Thin QFN Package
Ordering Information
PART
TEMP RANGE
PIN-PACKAGE
MAX8709BETI
-40°C to +85°C
28 Thin QFN
Applications
● Notebook Computer
● LCD Monitors
● LCD TVs
Displays
Pin Configuration appears at end of data sheet.
Minimal Operating Circuit
V
IN
BATT
GND
V
V
CC
DD
BST2
BST1
GH1
LOT
REF
MAX8709B
LX1
LX2
GL1
ILIM
CCV
CCI
PGND
GL2
GH2
VFB
SUS
SDA
SCL
ISEC
IFB
19-0768; Rev 1; 10/14
MAX8709B
High-Efficiency CCFL Backlight
Controller with SMBus Interface
Absolute Maximum Ratings
BATT to GND..........................................................-0.3V to +30V
BST1, BST2 to GND...............................................-0.3V to +36V
BST1 to LX1, BST2 to LX2........................................-0.3V to +6V
IFB, ISEC, VFB to GND...............................................-6V to +6V
SDA, SCL, SUS to GND............................................-0.3V to +6V
PGND to GND .......................................................-0.3V to +0.3V
GH1 to LX1.............................................-0.3V to (V
GH2 to LX2.............................................-0.3V to (V
+ 0.3V)
+ 0.3V)
Continuous Power Dissipation (T = +70°C)
BST1
A
28 Thin QFN (derate 20.84mW/°C above +70°C) .......1667mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
BST2
V
, V
to GND....................................................-0.3V to +6V
CC DD
REF, ILIM to GND.......................................-0.3V to (V
GL1, GL2 to GND.......................................-0.3V to (V
CCI, CCV, LOT to GND............................................-0.3V to +6V
+ 0.3V)
+ 0.3V)
CC
DD
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Electrical Characteristics
(Circuit of Figure 1. V
= 12V, V
= V
, V
= V , V
= 5.3V, T = 0°C to +85°C. Typical values are at T = +25°C,
BATT
LOT
REF CC
DD SUS A A
unless otherwise noted.)
PARAMETER
Input Voltage Range
CONDITIONS
MIN
4.6
TYP
MAX
5.5
28.0
3
UNITS
V
V
= V
= V
= V
BATT
CC
CC
DD
V
V
BATT
= open
5.5
DD
V
V
= 28V
1.5
BATT
BATT
V
Quiescent Current
V
= 5.5V
mA
BATT
BATT
SUS
= V
= 5V
3
CC
V
V
V
Quiescent Current, Shutdown
SUS = GND
= 5.5V, 6V < V
6
20
µA
V
V
0 < I
< 28V,
BATT
SUS
Output Voltage, Normal Operation
Output Voltage, Shutdown
5.0
3.5
5.35
4.6
5.5
CC
CC
< 20mA
LOAD
SUS = GND, no load
5.5
4.5
V
V
V
rising (leaving lockout)
falling (entering lockout)
CC
CC
V
Undervoltage-Lockout Threshold
V
CC
4.0
V
V
V
Undervoltage-Lockout Hysteresis
Power-On Reset (POR) Threshold
POR Hysteresis
200
1.75
50
mV
V
CC
CC
CC
Rising edge
0.90
1.96
2.70
mV
V
REF Output Voltage, Normal Operation
GH1, GH2, GL1, GL2 On-Resistance
GH1, GH2, GL1, GL2 Output Current
BST1, BST2 Leakage Current
Input Resonant Frequency
4.5V < V
< 5.5V, I
= 40µA
2.00
9
2.04
18
CC
LOAD
I
= 100mA, V
= V = 5.3V
DD
Ω
TEST
CC
0.5
A
V
_ = 12V, V _ = 7V
5
µA
kHz
ns
µs
BST
LX
Guaranteed by design
25
180
18
300
380
38
Minimum Off-Time
280
28
Maximum Off-Time
Current-Limit Threshold
ILIM = V
180
200
220
mV
mV
mV
CC
LX1 - GND, LX2 - GND (Fixed)
V
V
= 0.5V
= 2.0V
80
100
400
120
430
ILIM
ILIM
Current-Limit Threshold
LX1 - GND, LX2 - GND (Adjustable)
370
Minimum Current Threshold
LX1 - GND, LX2 - GND
6
Maxim Integrated
│ 2
www.maximintegrated.com
MAX8709B
High-Efficiency CCFL Backlight
Controller with SMBus Interface
Electrical Characteristics (continued)
(Circuit of Figure 1. V
= 12V, V
= V
, V
= V , V
= 5.3V, T = 0°C to +85°C. Typical values are at T = +25°C,
BATT
LOT
REF CC
DD SUS A A
unless otherwise noted.)
PARAMETER
CONDITIONS
MIN
0.5
-2
TYP
MAX
UNITS
V
LOT Input Voltage Range
LOT Input Bias Current
IFB Input Voltage Range
IFB Regulation Point
V
REF
+2
µA
V
-1.7
380
-2
+1.7
420
+2
400
mV
µA
mV
µS
MΩ
V
IFB Input Bias Current
IFB Lamp-Out Threshold
V
= 0.4V
IFB
LOT = REF
1V < V < 2.5V
500
600
100
20
700
IFB to CCI Transconductance
CCI Output Impedance
CCI
ISEC Input Voltage Range
ISEC Regulation Threshold
ISEC Input Bias Current
VFB Input Voltage Range
VFB Input Bias Current
-2
1.20
-2
+2
1.30
+2
1.25
V
V
V
= 1.25V
= 0.5V
µA
V
ISEC
-2
+2
-0.5
490
+0.5
530
µA
mV
µS
mV
MΩ
Hz
s
VFB
VFB Regulation Point
510
40
VFB to CCV Transconductance
1V < V
< 2.7V
CCV
VFB Zero-Voltage Crossing Threshold
CCV Output Impedance
-10
+10
20
DPWM Chopping Frequency
Lamp-Out Detection Timeout Timer
SDA, SCL, SUS Input Low Voltage
SDA, SCL, SUS Input High Voltage
SDA, SCL, SUS Input Hysteresis
SDA, SCL, SUS Input Bias Current
SDA Output Low Sink Current
SCL Serial Clock High Period
SCL Serial Clock Low Period
START Condition Setup Time
START Condition Hold Time
204
210
1.22
216
1.30
0.8
V
< 0.1V (Note 1)
1.14
IFB
V
2.1
V
300
mV
µA
mA
µs
-1
4
+1
V
= 0.4V
SDA
HIGH
LOW
T
T
4
4.7
4.7
4
µs
t
t
µs
SU:STA
HD:STA
µs
SDA Valid to SCL Rising-Edge Setup Time,
Slave Clocking-In Data
t
t
t
250
0
ns
ns
ns
SU:DAT
HD:DAT
DV
SCL Falling Edge to SDA Transition
SCL Falling Edge to SDA Valid,
Reading Out Data
700
Maxim Integrated
│ 3
www.maximintegrated.com
MAX8709B
High-Efficiency CCFL Backlight
Controller with SMBus Interface
Electrical Characteristics
(Circuit of Figure 1. V
= 12V, V
= V
, V
= V , V
= 5.3V, T = -40°C to +85°C. Typical values are at T = +25°C,
BATT
LOT
REF CC
DD SUS
A
A
unless otherwise noted.) (Note 2)
PARAMETER
CONDITIONS
MIN
4.6
TYP
MAX
5.5
28.0
3
UNITS
V
V
= V
= V
= V
BATT
CC
DD
V
V
Input Voltage Range
Quiescent Current
V
BATT
= open
5.5
CC
DD
V
V
= 28V
BATT
V
= 5.5V
mA
BATT
BATT
SUS
= V
= 5V
3
BATT
CC
V
V
V
Quiescent Current, Shutdown
SUS = GND
= 5.5V, 6V < V
20
µA
V
V
< 28V,
BATT
SUS
Output Voltage, Normal Operation
Output Voltage, Shutdown
5.0
3.5
5.5
CC
CC
0 < I
< 20mA
LOAD
SUS = GND, no load
5.5
4.5
V
V
rising (leaving lockout)
falling (entering lockout)
CC
CC
V
Undervoltage-Lockout Threshold
Power-On Reset (POR) Threshold
V
CC
V
4.0
V
Rising edge
4.5V < V
0.90
1.95
2.70
2.05
18
V
V
CC
REF Output Voltage, Normal Operation
GH1, GH2, GL1, GL2 On-Resistance
BST1, BST2 Leakage Current
Input Resonant Frequency
Minimum Off-Time
< 5.5V, I
= 40µA
CC
LOAD
I
= 100mA, V
= V = 5.3V
DD
Ω
TEST
CC
V
_ = 12V, V _ = 7V
5
µA
kHz
ns
µs
BST
LX
Guaranteed by design
25
180
18
300
380
38
Maximum Off-Time
Current-Limit Threshold
LX1 - GND, LX2 - GND (Fixed)
ILIM = V
180
220
mV
mV
CC
V
V
= 0.5V
= 2.0V
80
370
250
0.5
-2
120
430
450
Current-Limit Threshold
LX1 - GND, LX2 - GND (Adjustable)
ILIM
ILIM
Current-Limit Leading-Edge Blanking
LOT Input Voltage Range
LOT Input Bias Current
ns
V
V
REF
+2
µA
V
IFB Input Voltage Range
IFB Regulation Point
-1.7
380
-2
+1.7
420
+2
mV
µA
mV
V
IFB Input Bias Current
V
= 0.4V
IFB
IFB Lamp-Out Threshold
ISEC Input Voltage Range
ISEC Regulation Point
LOT = REF
500
-2
700
+2
1.20
-2
1.30
+2
V
ISEC Input Bias Current
VFB Input Voltage Range
VFB Input Bias Current
V
V
= 1.25V
= 0.5V
µA
V
ISEC
-2
+2
-0.5
490
-10
204
+0.5
530
+10
216
µA
mV
mV
Hz
VFB
VFB Regulation Point
VFB Zero-Voltage Crossing Threshold
DPWM Chopping Frequency
Maxim Integrated
│ 4
www.maximintegrated.com
MAX8709B
High-Efficiency CCFL Backlight
Controller with SMBus Interface
Electrical Characteristics (continued)
(Circuit of Figure 1. V
= 12V, V
= V
, V
= V , V
= 5.3V, T = -40°C to +85°C. Typical values are at T = +25°C,
BATT
LOT
REF CC
DD SUS A A
unless otherwise noted.) (Note 2)
PARAMETER
Lamp-Out Detection Timeout Timer
SDA, SCL, SUS Input Low Voltage
SDA, SCL, SUS Input High Voltage
SDA, SCL, SUS Input Bias Current
SDA Output Low Sink Current
SCL Serial Clock High Period
SCL Serial Clock Low Period
START Condition Setup Time
START Condition Hold Time
CONDITIONS
< 0.1V (Note 1)
MIN
TYP
MAX
1.30
0.8
UNITS
s
V
1.14
IFB
V
2.1
-1
4
V
+1
µA
mA
µs
V
= 0.4V
SDA
HIGH
LOW
T
T
4
4.7
4.7
4
µs
t
t
µs
SU:STA
HD:STA
µs
SDA Valid to SCL Rising-Edge Setup Time,
Slave Clocking-In Data
t
t
250
0
ns
ns
SU:DAT
HD:DAT
SCL Falling Edge to SDA Transition
Note 1: Corresponds to 256 DPWM cycles.
Note 2: Specifications to -40°C are guaranteed by design based on final characterization results.
Typical Operating Characteristics
(Circuit of Figure 1. V
= 12V, V
= V
, V
= V , V
= 5.3V, T = +25°C, unless otherwise noted.)
BATT
LOT
REF CC
DD SUS A
LOW INPUT-VOLTAGE
OPERATION (V = 8V)
HIGH INPUT-VOLTAGE
OPERATION (V = 20V)
LINE-TRANSIENT RESPONSE
MAX8709 toc03
BATT
BATT
MAX8709 toc01
MAX8709 toc02
0V
0V
A
B
0V
0V
A
B
A
B
C
8V
0V
0V
0V
C
D
C
D
0V
0V
0V
0V
D
10µs/div
10µs/div
40µs/div
A: V , 2V/div
A: V , 2V/div
A: V , 5V/div
BATT
IFB
IFB
B: V , 2V/div
B: V , 2V/div
B: V , 2V/div
VFB
VFB
IFB
C: V , 10V/div
C: V , 10V/div
C: V , 2V/div
VFB
LX1
LX1
D: V , 10V/div
D: V , 10V/div
D: V , 10V/div
LX2
LX2
LX1
Maxim Integrated
│ 5
www.maximintegrated.com
MAX8709B
High-Efficiency CCFL Backlight
Controller with SMBus Interface
Typical Operating Characteristics (continued)
(Circuit of Figure 1. V
= 12V, V
= V
, V
= V , V
= 5.3V, T = +25°C, unless otherwise noted.)
BATT
LOT
REF CC
DD SUS A
STARTUP
DPWM OPERATION (10%)
DPWM OPERATION (50%)
MAX8709 toc06
MAX8709 toc04
MAX8709 toc05
A
B
A
B
A
B
0V
0V
1.2V
0V
1.2V
0V
C
D
0V
0V
C
C
0V
0V
2ms/div
1ms/div
1ms/div
A: V , 5V/div
SUS
A: V , 200mV/div
A: V , 200mV/div
CCV
CCV
B: V , 2V/div
B: V , 1V/div
B: V , 1V/div
IFB
IFB
IFB
C: V , 2V/div
VFB
C: V , 1V/div
VFB
C: V , 1V/div
VFB
D: V , 10V/div
LX1
LAMP-OUT VOLTAGE
DPWM SOFT-START
DPWM SOFT-STOP
LIMITING AND TIMEOUT
MAX8709 toc07
MAX8709 toc08
MAX8709 toc09
CCI
CCI
A
B
1.2V
0V
CCV
0V
0V
CCV
A
B
A
B
0V
0V
0V
200ms/div
40µs/div
40µs/div
A: V , 1V/div
A: V , 1V/div
A: V , 1V/div
VFB
IFB
IFB
B: V , 1V/div
B: V , 1V/div
B: V , 1V/div
VFB
VFB
IFB
Maxim Integrated
│ 6
www.maximintegrated.com
MAX8709B
High-Efficiency CCFL Backlight
Controller with SMBus Interface
Typical Operating Characteristics (continued)
(Circuit of Figure 1. V
= 12V, V
= V
, V
= V , V
= 5.3V, T = +25°C, unless otherwise noted.)
BATT
LOT
REF CC
DD SUS A
SWITCHING FREQUENCY
vs. INPUT VOLTAGE
DPWM FREQUENCY
vs. INPUT VOLTAGE
ELECTRICAL EFFICIENCY
vs. INPUT VOLTAGE
62
58
54
50
46
220
215
210
205
200
100
90
80
70
60
50
7
10
13
16
19
22
25
7
10
13
16
19
22
25
7
10
13
16
19
22
25
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
NORMALIZED RMS LAMP CURRENT
vs. INPUT VOLTAGE
NORMALIZED BRIGHTNESS
vs. BRIGHTNESS CODE
REF LOAD REGULATION
0.8
0.6
0.4
0.2
0
100
80
60
40
20
0
0.10
0.05
0
-0.05
-0.10
-0.15
-0.2
-0.4
-0.6
-0.8
7
10
13
16
19
22
25
0
20
40
60
80
100
0
4
8
12 16 20 24 28 32
BRIGHTNESS CODE
INPUT VOLTAGE (V)
REF LOAD CURRENT (µA)
NORMALIZED V LINE REGULATION
REF OUTPUT vs. TEMPERATURE
V
CC
LOAD REGULATION
CC
0.2
0
0.05
0
0
-0.3
-0.6
-0.9
-1.2
-1.5
V
= 5.3V
CC
-0.2
-0.4
-0.6
-0.8
-1.0
-0.05
-0.10
-0.15
-0.20
-0.25
5
10
15
20
25
-40 -20
0
20
40
60
80 100
0
4
8
12
16
20
INPUT VOLTAGE (V)
EXTERNAL LOAD CURRENT (mA)
TEMPERATURE (°C)
Maxim Integrated
│ 7
www.maximintegrated.com
MAX8709B
High-Efficiency CCFL Backlight
Controller with SMBus Interface
Pin Description
PIN
NAME
FUNCTION
Current-Limit Threshold Adjustment. Connect a resistive voltage-divider between REF or V
and GND.
CC
1
ILIM
The current-limit threshold measured between LX_ and GND is 1/5 the voltage forced at ILIM. The ILIM
adjustment range is 0 to 3V. Connect ILIM to V to select the default current-limit threshold of 0.2V.
CC
2V Reference Output. Bypass REF to GND with a 0.1µF ceramic capacitor. REF is discharged to GND
during shutdown.
2
3
4
5
REF
LOT
Lamp-Out Threshold Adjustment. The lamp-out threshold is 30% of the voltage at LOT. The LOT
adjustment range is from 0.5V to V
.
REF
Analog Ground. The ground return for V , REF, and other analog circuitry. Connect GND to PGND
CC
under the IC at the IC’s backside exposed metal pad.
GND
ISEC
Secondary Current-Limit Sense Input. The secondary current limit controls the transformer secondary
current even if the IFB sense resistor is shorted. See the Secondary Current Limit (ISEC) section.
6
7
8
SDA
SCL
SUS
SMBus Serial Data Input
SMBus Serial Clock Input
SMBus Suspend Input
9, 10, 11,
23
N.C.
No Connection. Not internally connected.
Gate-Driver Supply Input. Connect V
0.1µF capacitor to PGND.
to V , the output of the linear regulator. Bypass V
with a
DD
CC
DD
12
V
DD
13
14
15
16
PGND
GL2
Power Ground. Gate-driver current flows through this pin.
Low-Side MOSFET NL2 Gate-Driver Output
Low-Side MOSFET NL1 Gate-Driver Output
High-Side MOSFET NH1 Gate-Driver Output
GL1
GH1
Switching Node Connection. LX1 is the internal gate driver’s (GH1’s) source connection for the high-side
MOSFET NH1. LX1 is also the sense input to the current comparators.
17
18
19
LX1
Driver Bootstrap Input for High-Side MOSFET NH1. Connect BST1 through a diode to V
0.1µF capacitor to LX1 (Figure 1).
and through a
DD
BST1
BST2
Driver Bootstrap Input for High-Side MOSFET NH2. Connect BST2 through a diode to V
0.1µF capacitor to LX2 (Figure 1).
and through a
DD
Switching Node Connection. LX2 is the internal gate driver’s (GH2’s) source connection for the high-side
MOSFET NH2. LX2 is also the sense input to the current comparators.
20
21
LX2
GH2
High-Side MOSFET NH2 Gate-Driver Output
Lamp Output Feedback Sense Input. The average value on VFB is regulated during startup and open-
lamp conditions to 0.5V by controlling the on-time of high-side switches. A capacitive voltage-divider
between the CCFL lamp output and GND is sensed to set the maximum average lamp output voltage.
22
24
VFB
IFB
Lamp Current-Sense Input. The voltage on IFB is used to regulate the lamp current. If the IFB input falls
below 30% of the LOT voltage for 1.22s, then the MAX8709B activates the lamp-out fault latch.
Current-Loop Compensation Pin. CCI is the output of the current-loop transconductance amplifier (GMI)
that regulates the CCFL current. The CCI voltage controls the time interval during which the full bridge
applies the input voltage (BATT) to the transformer primary. Connect CCI to GND through a 0.1µF
capacitor. CCI is internally discharged to GND in shutdown.
25
CCI
Maxim Integrated
│ 8
www.maximintegrated.com
MAX8709B
High-Efficiency CCFL Backlight
Controller with SMBus Interface
Pin Description (continued)
PIN
NAME
FUNCTION
Voltage-Loop Compensation Pin. CCV is the output of the voltage-loop transconductance amplifier (GMV)
that regulates the maximum average secondary transformer voltage. The CCV voltage controls the time
interval during which the full bridge applies the input voltage (BATT) to the transformer primary. The CCV
capacitor also sets the rise time and fall time of the lamp current in DPWM. Connect CCV to GND with a
6.8nF capacitor. CCV is internally discharged to GND in shutdown.
26
CCV
MAX8709B Supply Input. Input to the internal 5.3V linear regulator (V ) that provides power to the
CC
device. Bypass BATT to GND with a 0.1µF capacitor.
27
28
BATT
5.3V Linear-Regulator Output. V
is the supply voltage for the MAX8709B. Bypass V
to GND with a
CC
CC
V
CC
0.47µF ceramic capacitor. V
can also be connected to BATT if V
< 5.5V.
CC
BATT
V
IN
7V TO 24V
C1
4.7µF
25V
BATT
V
V
CC
C8
0.1µF
C7
0.47µF
DD
GND
LOT
D1
BST2
BST1
GH1
REF
ILIM
C9
0.1µF
NH1 NH2
R4
C2
1µF
C6
0.1µF
100kΩ
T1
1:93
MAX8709B
CCFL
LX1
LX2
GL1
C5
0.1µF
R5
100kΩ
NL1 NL2
C3
15pF
3kV
CCV
CCI
C10
0.01µF
PGND
GL2
C11
0.1µF
GH2
VFB
ISEC
IFB
SMBSUS
SMBDATA
SMBCLK
SUS
SDA
SCL
R1
150Ω
1%
C4
22nF
R2
2kΩ
R3
40.2Ω
1%
Figure 1. Typical Operating Circuit
Maxim Integrated
│ 9
www.maximintegrated.com
MAX8709B
High-Efficiency CCFL Backlight
Controller with SMBus Interface
Figure 2. Functional Diagram
Maxim Integrated
│ 10
www.maximintegrated.com
MAX8709B
High-Efficiency CCFL Backlight
Controller with SMBus Interface
Table 1. Component List
DESIGNATION
DESCRIPTION
DESIGNATION
DESCRIPTION
0.47µF ±10%, 10V X5R
4.7µF ±20%, 25V X5R
ceramic capacitor (0603)
Taiyo Yuden LMK107BJ474KA
TDK C1608X5R1A474K
ceramic capacitor (1210)
Murata GRM32RR61E475K
Taiyo Yuden TMK325BJ475MN
TDK C3225X7R1E475M
C7
D1
C1
Dual silicon switching diode,
common anode (SOT-323)
Central Semiconductor CMSD2836
Diodes Incorporated BAW56W
1µF ±10%, 25V X7R
ceramic capacitor (1206)
Murata GRM31MR71E105K
Taiyo Yuden TMK316BJ105KL
TDK C3216X7R1E105K
C2
C3
C4
30V, 0.095 dual n-channel MOSFETs
(6-pin SOT23)
Fairchild FDC6561AN
NH1/2,
NL1/2
15pF ±1pF, 3kV high-voltage
ceramic capacitor (1808)
Murata GRM42D1X3F150J
TDK C4520C0G3F150F
R1
R2
150Ω ±1% resistor (0603)
2kΩ ±5% resistor (0603)
39Ω ±1% resistor (0603)
100kΩ ±5% resistors (0603)
R3
0.022µF ±10%, 16V X7R
ceramic capacitor (0402)
Murata GRP155R71C223K
Taiyo Yuden EMK105BJ223KV
TDK C1005X7R1C223K
R4, R5
CCFL transformer, 1:93 turns ratio
Sumida 5371-400-W1423
TOKO T912MG-1018
T1
0.1µF ±10%, 25V X7R
Detailed Description
ceramic capacitors (0603)
Murata GRM188R71E104K
Taiyo Yuden TMK107BJ104KA
TDK C1608X7R1E104K
C5, C6,
C8, C9
The MAX8709B controls a full-bridge resonant inverter to
convert an unregulated DC input into a near-sinusoidal
AC output for powering CCFLs. The lamp brightness is
adjusted by turning the lamp on and off with an internal
DPWM signal. The duty cycle of the DPWM signal is set
through an SMBus-compatible 2-wire serial interface.
Figure 2 shows the functional diagram of the MAX8709B.
Table 2. Component Suppliers
SUPPLIER
Central Semiconductor
Fairchild Semiconductor
Murata
WEBSITE
www.centralsemi.com
www.fairchildsemi.com
www.murata.com
Resonant Operation
TheMAX8709Bdrivesthefourn-channelpowerMOSFETs
that make up the zero-voltage-switching (ZVS) full-bridge
inverter as shown in Figure 3. Assume that NH1 and NL2
are turned on at the beginning of a switching cycle as
shown in Figure 3(a). The primary current flows through
MOSFET NH1, DC blocking cap C2, the primary side of
transformer T1, and MOSFET NL2. During this interval,
the primary current ramps up until the controller turns off
NH1. When NH1 turns off, the primary current forward
biases the body diode of NL1, which clamps the LX1
voltage just below ground as shown in Figure 3(b). When
the controller turns on NL1, its drain-tosource voltage is
near zero because its forward-biased body diode clamps
the drain. Since NL2 is still on, the primary current flows
through NL1, C2, the primary side of T1, and NL2. Once
the primary current drops to the minimum current thresh-
Sumida
www.sumida.com
Taiyo Yuden
www.t-yuden.com
TDK
www.components.tdk.com
Typical Operating Circuit
The Typical Operating Circuit of the MAX8709B (Figure
1) is a complete CCFL backlight inverter for notebook
TFT LCD panels. The circuit works over an input voltage
range of 7V to 24V with an RMS lamp current of 6mA. The
circuit’s maximum RMS open-lamp voltage is limited to
1600V. Table 1 lists recommended component options, and
Table 2 lists the component suppliers’ contact information.
old (6mV / R
), the controller turns off NL2. The
DS(ON)
remaining energy in T1 charges up the LX2 node until the
body diode of NH2 is forward biased.
Maxim Integrated
│ 11
www.maximintegrated.com
MAX8709B
High-Efficiency CCFL Backlight
Controller with SMBus Interface
VBATT
VBATT
NH1
ON
NH2
OFF
NH1
OFF
NH2
ON
T1
T1
C2
C2
LX1
LX2
LX1
LX2
NL1
OFF
NL2
ON
NL1
ON
NL2
OFF
(a)
(c)
VBATT
VBATT
NH1
OFF
NH2
OFF
NH1
OFF
NH2
OFF
T1
T1
C2
C2
LX1
LX2
LX1
LX2
NL1
ON
NL2
ON
NL1
ON
NL2
ON
(BODY DIODE TURNS ON FIRST)
(BODY DIODE TURNS ON FIRST)
(d)
(b)
Figure 3. Resonant Operation
When NH2 turns on, it does so with near-zero drain-
tosource voltage. The primary current reverses polarity as
shown in Figure 3(c), beginning a new cycle with the cur-
rent flowing in the opposite direction, with NH2 and NL1
on. The primary current ramps up until the controller turns
off NH2. When NH2 turns off, the primary current forward
biases the body diode of NL2, which clamps the LX2
voltage just below ground as shown in Figure 3(d). After
the LX2 node goes low, the controller losslessly turns on
NL2. Once the primary current drops to the minimum cur-
rent threshold, the controller turns off NL1. The remaining
energy charges up the LX1 node until the body diode of
NH1 is forward biased. Finally, NH1 losslessly turns on,
beginning a new cycle as shown in Figure 3(a). Note that
switching transitions on all four power MOSFETs occur
under ZVS conditions, which reduce transient power
losses and EMI.
The simplified CCFL inverter circuit is shown in Figure
4(a). The full-bridge power stage is simplified and repre-
sented as a square-wave AC source. The resonant tank
circuit can be further simplified to Figure 4(b) by removing
the transformer. C is the primary series capacitor, C’
is the series capacitance reflected to the secondary, C
S
S
P
is the secondary parallel capacitor, N is the transformer
turns ratio, L is the transformer secondary leakage induc-
tance, and R is an idealized resistance that models the
L
CCFL in normal operation.
Maxim Integrated
│ 12
www.maximintegrated.com
MAX8709B
High-Efficiency CCFL Backlight
Controller with SMBus Interface
C
S
L
1:N
4
3
AC
SOURCE
C
P
CCFL
R INCREASING
L
(a)
2
1
0
C
S
C'
S
=
N2
L
AC
SOURCE
0
20
40
60
80
100
C
P
R
L
FREQUENCY (kHz)
(b)
Figure 4. Equivalent Resonant Tank Circuit
Figure 5. Frequency Response of the Resonant Tank
Figure 5 shows the frequency response of the resonant
tank’s voltage gain under different load conditions. The
primary series capacitor is 1μF, the secondary parallel
capacitor is 15pF, the transformer turns ratio is 1:93, and
the secondary leakage inductance is 260mH. Notice there
Once the lamp is ionized, the equivalent load resistance
decreases rapidly and the operating point moves toward
the series resonant peak. The series resonant operation
causes the circuit to behave like a current source.
Current and Voltage Control Loops
(CCI, CCV)
are two peaks, f and f , in the frequency response. The
S
P
first peak, f , is the series resonant peak determined by
S
The MAX8709B uses a current loop and a voltage loop
to control the power delivered to the CCFL. The current
loop is the dominant loop in regulating the lamp current.
The voltage loop limits the transformer secondary volt-
age and is active during startup, the DPWM offtime, and
open-lamp fault.
the reflected series capacitor and the secondary leakage
inductance:
1
f
=
S
2π LC'
S
The second peak, f , is the parallel resonant peak
P
Both the current and the voltage loops use transconduc-
tance error amplifiers for regulation. The AC lamp current
is measured with a sense resistor in series with the CCFL.
The voltage across this resistor is applied to the IFB input
and is internally half-wave rectified. The current-loop
transconductance error amplifier compares the rectified
IFB voltage with a 400mV internal threshold to create an
error current. The error current charges and discharges a
capacitor connected between CCI and ground to gener-
determined by the reflected series capacitor, the parallel
capacitor, and the secondary leakage inductance:
1
f
=
P
C' C
S
P
2π L
C' + C
S
P
These two frequencies set the lower and upper bound-
aries of resonant operation. When the lamp is off, the
operating point of the resonant tank is close to the par-
allel resonant peak due to the infinite lamp impedance.
The circuit displays the characteristics of a parallelloaded
resonant converter, acting like a voltage source to gen-
erate the necessary striking voltage. Theoretically, the
output voltage of the resonant converter keeps going until
the lamp is ionized.
ate an error voltage V
. Similarly, the AC voltage across
CCI
the transformer secondary winding is measured through
a capacitive voltage-divider. The sense voltage is applied
to the VFB input and is internally half-wave rectified. The
voltage-loop transconductance error amplifier compares
the rectified VFB voltage with a 500mV internal threshold
to create an error current. The error current charges and
Maxim Integrated
│ 13
www.maximintegrated.com
MAX8709B
High-Efficiency CCFL Backlight
Controller with SMBus Interface
discharges a capacitor connected between CCV and
is not critical. When V
is very low, the controller loses
BATT
ground to generate an error voltage V
. The lower of
current regulation and runs at maximum duty cycle. Under
these circumstances, a transient overvoltage condition
could occur when the AC adapter is suddenly applied to
power the circuit. The feed-forward circuitry minimizes
variations in lamp voltage due to such input voltage steps.
CCV
V
CCI
and V
takes control and is compared with an
CCV
internal ramp signal to set the high-side MOSFET switch
on-time (t ).
ON
Lamp Startup
The regulator also clamps the voltage on V
. These
CCI
A CCFL is a gas discharge lamp that is normally driven
in the avalanche mode. To start ionization in a nonion-
ized lamp, the applied voltage (striking voltage) must be
increased to the level required for the start of avalanche.
The striking voltage can be several times the typical oper-
ating voltage.
two features together ensure that overvoltage transients
do not appear on the transformer when leaving dropout.
The V
clamp is unique in that it limits V
to the
CCI
CCI
peak voltage of the PWM ramp. As the circuit reaches
dropout, V approaches the PWM ramp’s peak in order
CCI
to reach maximum t . If V
decreases further, the
ON
BATT
Because of the resonant topology, the striking voltage
is guaranteed regardless of the temperature. Before the
lamp is ionized, the lamp impedance is infinite. The trans-
former secondary leakage inductance and the high-volt-
age parallel capacitor determine the unloaded resonant
frequency. Since the unloaded resonant circuit has a high
Q, it is easy to generate high voltages across the lamp.
control loop loses regulation and V
tries to reach its
prevents this from
CCI
positive supply rail. The clamp on V
happening and V
CCI
rides just above the PWM ramp’s
CCI
peak. If V
continues to decrease, the feed-forward
BATT
control reduces the amplitude of the PWM ramp and the
clamp pulls V
down. When V
suddenly steps out
CCI
BATT
of dropout, V
is still low and maintains the drive on the
CCI
transformer at the old dropout level. The control loop then
Operation during startup differs from the steady-state con-
slowly corrects and increases V
back into regulation.
to bring the circuit
dition described in the Current and Voltage Control Loops
CCI
section. Upon power-up, V
slowly rises, increasing
CCI
the duty cycle, which provides soft-start. During this time,
is limited to 150mV above V . Once the second-
ary voltage reaches the strike voltage, the lamp current
begins to increase. When the lamp current reaches the
DPWM Dimming Control
V
CCV
CCI
The MAX8709B controls the brightness of the CCFL by
“chopping” the lamp current on and off using an inter-
nal DPWM signal. The frequency of the DPWM signal
is 210Hz. The brightness code set through the SMBus
interface determines the duty cycle of the DPWM signal. A
brightness code of 0b00000 corresponds to a 12.5% duty
cycle for the MAX8709B. A brightness code of 0b11111
corresponds to a 100% DPWM duty cycle. The duty cycle
changes by 3.125% per step. Codes 0b00000 to 0b00011
all produce 12.5% for the MAX8709B.
regulation point, V
steady state.
exceeds V
and it reaches
CCI
CCV
Feed-Forward Control and
Dropout Operation
The MAX8709B is designed to maintain tight control of the
transformer secondary under all transient conditions includ-
ing dropout. The feed-forward control instantaneously
adjusts the t
time for changes in input voltage (V
).
ON
BATT
In DPWM operation, the CCI and CCV control loops work
together to regulate the lamp current, limit the secondary
voltage, and control the rising and falling of the lamp cur-
rent. During the DPWM off-cycle, the output of the volt-
age-loop error amplifier (CCV) is set to 1.15V and the cur-
rent-loop error-amplifier output (CCI) is high impedance.
The high-impedance output acts like a sampleand- hold
This feature provides immunity to input voltage variations
and simplifies loop compensation over wide input voltage
ranges. The feed-forward control also improves the line
regulation for short DPWM on-times and makes startup
transients less dependent on the input voltage.
Feed-forward control is implemented by increasing the
circuit to keep V
At the beginning of the DPWM on-cycle, V
rises, gradually increasing t , which provides soft-start.
from changing during the off-cycles.
PWM’s internal voltage ramp rate for higher V
. This has
CCI
BATT
linearly
the effect of varying t
as a function of the input voltage
CCV
ON
while maintaining about the same signal levels at V
and
ON
CCI
Once V
exceeds V
, the current-loop error ampli-
V . Since the required voltage change across the com-
CCV
CCV
CCI
fier takes control and starts to regulate the lamp current.
In the meantime, V continues to rise and is limited to
pensation capacitors is minimal, the controller’s response to
input voltage changes is essentially instantaneous.
CCV
150mV above V
. At the end of the DPWM on-cycle,
CCI
To maximize run time, it may be desirable to allow the
circuit to operate in dropout if the backlight’s performance
the CCV capacitor discharges linearly, gradually decreas-
ing t and providing soft-stop.
ON
Maxim Integrated
│ 14
www.maximintegrated.com
MAX8709B
High-Efficiency CCFL Backlight
Controller with SMBus Interface
POR and UVLO
Primary Overcurrent Protection (ILIM)
The MAX8709B includes power-on-reset (POR) and
undervoltage-lockout (UVLO) circuits. The POR resets
all internal registers such as DAC outputs, fault latches,
The MAX8709B senses primary current in each switching
cycle. When the regulator turns on the low-side MOSFET,
a comparator monitors the voltage drop from LX_ to GND.
If the voltage exceeds the current-limit threshold, the reg-
ulator turns off the high-side switch at the opposite side
of the primary to prevent the transformer primary current
from increasing further.
and all SMBus registers. POR occurs when V
is below
CC
1.5V. The SMBus input logic thresholds are only guaran-
teed to meet electrical characteristic limits for V as low
CC
as 3.5V, but the interface continues to function down to
the POR threshold.
The current-limit threshold can be adjusted using the ILIM
input. Connect a resistive voltage-divider between REF or
The UVLO is activated and disables both high-side and
low-side switch drivers when V
is below 4.2V (typ).
V
and GND with the midpoint connected to ILIM. The
CC
CC
current-limit threshold measured between LX_ and GND
is 1/5 the voltage at ILIM. The ILIM adjustment range is 0
Low-Power Shutdown (SUS)
When the MAX8709B is placed in shutdown, all func-
tions of the IC are turned off except for the 5.3V linear
regulator that powers all internal registers and the SMBus
interface. The SMBus interface is accessible in shutdown.
In shutdown, the linear-regulator output voltage drops to
about 4.5V and the supply current is 6μA (typ), which is
the required power to maintain all internal register states.
While in shutdown, lamp-out detection and short-circuit
detection latches are reset. The device can be placed into
shutdown either by writing to the shutdown-mode register
or pulling SUS low.
to 3V. Connect ILIM to V
limit threshold of 0.2V.
to select the default current-
CC
Secondary Current Limit (ISEC)
The secondary current limit provides fail-safe current lim-
iting in case a failure, such as a short circuit or leakage
from the lamp high-voltage terminal to ground, prevents
the CCI current control loop from functioning properly.
ISEC monitors the voltage across a sense resistor placed
between the transformer’s low-voltage secondary terminal
and ground. The ISEC voltage is internally half-wave rec-
tified and continuously compared to the ISEC regulation
threshold (1.25V typ). Any time the ISEC voltage exceeds
the threshold, a controlled current is drawn from CCI to
reduce the on-time of the bridge’s high-side switches.
Lamp-Out Protection
For safety, the MAX8709B monitors the lamp-current
feedback (IFB) to detect faulty or open CCFL tubes and
secondary short circuits in the lamp and IFB sense resistor.
If the voltage on IFB is continuously below 30% of the LOT
voltage for greater than 1.22s (typ), the MAX8709B latches
off the full bridge. Unlike the normal shutdown mode, the
Reference Output (REF)
The reference output is nominally 2V, and can source at
least 40μA (see the Typical Operating Characteristics).
Bypass REF with a 0.22μF ceramic capacitor connected
between REF and GND.
linear-regulator output (V ) remains at 5.3V. Toggling
CC
SUS or cycling the input power reactivates the device.
During the 1.22s delay, V
slowly rises, increasing
CCI
Linear-Regulator Output (V
)
CC
t
in an attempt to maintain lamp current regulation. As
ON
The internal linear regulator steps down the DC input
voltage to 5.3V (typ). The linear regulator supplies power
to the internal control circuitry of the MAX8709B and can
also be used to power the MOSFET drivers by connect-
V
CCI
rises, V
rises with it until the secondary voltage
CCV
reaches its preset limit. At this point, V
its the secondary voltage by limiting t . Because V
is limited to 150mV above V
is able to quickly limit the secondary voltage. Without this
clamping feature, the transformer voltage overshoots to
stops and lim-
CCV
ON
CCV
, the voltage control loop
CCI
ing V
directly to V . The V
voltage drops to 4.5V
CC
DD
CC
in shutdown.
dangerous levels because V
from its supply rail.
takes time to slew down
CCV
Maxim Integrated
│ 15
www.maximintegrated.com
MAX8709B
High-Efficiency CCFL Backlight
Controller with SMBus Interface
Write-Byte Format
ACK
S
ADDRESS
WR
COMMAND
ACK
DATA
ACK
P
7 BITS
1B
1B
8 BITS
1B
8 BITS
1B
SLAVE ADDRESS
COMMAND BYTE: SELECTS
WHICH REGISTER YOU ARE
WRITING TO
DATA BYTE: DATA GOES INTO THE
REGISTER SET BY THE COMMAND BYTE
Read-Byte Format
S
ADDRESS
7 BITS
WR
ACK
COMMAND
ACK
S
ADDRESS
7 BITS
RD
ACK
DATA
///
P
1B
1B
8 BITS
1B
1B
1B
8 BITS
1B
SLAVE ADDRESS
COMMAND BYTE: SELECTS
WHICH REGISTER YOU ARE
READING FROM
SLAVE ADDRESS: REPEATED
DUE TO CHANGE IN DATA-
FLOW DIRECTION
DATA BYTE: READS FROM
THE REGISTER SET BY THE
COMMAND BYTE
Send-Byte Format
Receive-Byte Format
S
ADDRESS
WR
ACK
1B
COMMAND
ACK
P
S
ADDRESS
7 BITS
RD
ACK
DATA
///
P
7 BITS
1B
8 BITS
1B
1B
1B
8 BITS
1B
DATA BYTE: READS DATA FROM
THE REGISTER COMMANDED BY
THE LAST READ-BYTE OR WRITE-
BYTE TRANSMISSION; ALSO USED
FOR SMBUS ALERT RESPONSE
RETURN ADDRESS
COMMAND BYTE: SENDS COMMAND
WITH NO DATA; USUALLY USED FOR
ONE-SHOT COMMAND
SLAVE ADDRESS
S = START CONDITIONSHADED = SLAVE TRANSMISSIONWR = WRITE = 0
P = STOP CONDITIONACK= ACKNOWLEDGED = 0RD = READ =1
/// = NOT ACKNOWLEDGED = 1
Figure 6. SMBus Protocols
The MAX8709B is a slave-only device and responds
to the 7-bit address 0b01011000 (i.e., with the R/W bit
clear indicating a write, this corresponds to 0x58). The
MAX8709B has three functional registers: a 5-bit bright-
ness register (BRIGHT4–BRIGHT0), a 3-bit shutdown-
mode register (SHMD2–SHMDE0), and a 2-bit status reg-
ister (STATUS1–STATUS0). In addition, the device has
three identification (ID) registers: an 8-bit chip ID register,
an 8-bit chip revision register, and an 8-bit manufacturer
ID register.
SMBus Interface (SDA, SCL)
The MAX8709B supports an Intel SMBus-compatible 2-
wire digital interface. SDA is the bidirectional data line and
SCL is the clock line of the 2-wire interface corresponding
respectively to SMBDATAand SMBCLK lines of the SMBus.
SDA and SCL are Schmidt-triggered inputs that can accom-
modate slow edges; however, the rising and falling edges
should still be faster than 1μs and 300ns, respectively. The
MAX8709B use the write-byte, read-byte, and receive-byte
protocols (Figure 6). The SMBus protocols are documented
in System Management Bus Specification V1.1 and are
available at www.SMBus.org.
Maxim Integrated
│ 16
www.maximintegrated.com
MAX8709B
High-Efficiency CCFL Backlight
Controller with SMBus Interface
A
B
C
D
E
F
G
H
I
J
K
L
M
t
t
HIGH
LOW
SMBCLK
SMBDATA
t
t
t
t
t
HD:DAT
HD:STA
SU:STA
SU:DAT
HD:DAT
t
SU:STO
t
BUF
A = START CONDITION
F = ACKNOWLEDGE BIT CLOCKED INTO MASTER
G = MSB OF DATA CLOCKED INTO SLAVE
H = LSB OF DATA CLOCKED INTO SLAVE
I = SLAVE PULLS SMBDATA LINE LOW
J = ACKNOWLEDGE CLOCKED INTO MASTER
K = ACKNOWLEDGE CLOCK PULSE
L = STOP CONDITION, DATA EXECUTED BY SLAVE
M = NEW START CONDITION
B = MSB OF ADDRESS CLOCKED INTO SLAVE
C = LSB OF ADDRESS CLOCKED INTO SLAVE
D = R/W BIT CLOCKED INTO SLAVE
E = SLAVE PULLS SMBDATA LINE LOW
Figure 7. SMBus Write Timing
A
B
C
D
E
F
G
H
I
J
K
t
t
HIGH
LOW
SMBCLK
SMBDATA
t
t
t
t
t
t
t
BUF
SU:STA HD:STA
SU:DAT
HD:DAT
SU:DAT
SU:STO
A = START CONDITION
E = SLAVE PULLS SMBDATA LINE LOW
I = ACKNOWLEDGE CLOCK PULSE
J = STOP CONDITION
K = NEW START CONDITION
B = MSB OF ADDRESS CLOCKED INTO SLAVE
C = LSB OF ADDRESS CLOCKED INTO SLAVE
D = R/W BIT CLOCKED INTO SLAVE
F = ACKNOWLEDGE BIT CLOCKED INTO MASTER
G = MSB OF DATA CLOCKED INTO MASTER
H = LSB OF DATA CLOCKED INTO MASTER
Figure 8. SMBus Read Timing
Communication starts with the master signaling the begin-
ning of a transmission with a START condition, which is
a high-to-low transition on SDA while SCL is high. When
the master has finished communicating with the slave,
the master issues a STOP condition, which is a low-to-
high transition on SDA while SCL is high. The bus is then
free for another transmission. Figures 7 and 8 show the
timing diagrams for signals on the 2-wire interface. The
address byte, command byte, and data byte are transmit-
ted between the START and STOP conditions. The SDA
state is allowed to change only while SCL is low, except
for the START and STOP conditions. Data is transmitted
in 8-bit words and is sampled on the rising edge of SCL.
Nine clock cycles are required to transfer each byte in or
out of the MAX8709B since either the master or the slave
acknowledges the receipt of the correct byte during the
ninth clock. If the MAX8709B receives the correct slave
address followed by R/W = 0, it expects to receive 1 or
2 bytes of information (depending on the protocol). If the
device detects a START or STOP condition prior to clock-
ing in the bytes of data, it considers this an error condition
and disregards all the data.
If the transmission is completed correctly, the registers
are updated immediately after a STOP (or RESTART)
condition. If the MAX8709B receives its correct slave
address followed by R/W = 1, it expects to clock out the
register data selected by the previous command byte.
Maxim Integrated
│ 17
www.maximintegrated.com
MAX8709B
High-Efficiency CCFL Backlight
Controller with SMBus Interface
Table 3. Commands Description
DATA REGISTER BIT ASSIGNMENT
SMBus
PROTOCOL
COMMAND
BYTE*
POR
STATE
BIT 7
(MSB)
BIT 0
(LSB)
BIT 6
BIT 5
BIT 4
BIT 3
BRIGHT3 BRIGHT2 BRIGHT1
SHMD2 SHMD1
BIT 2
BIT 1
Read and
Write
0x01
0b0XXX XX01
BRIGHT4
(MSB)
BRIGHT0
(LSB)
0x17
0
0
0
1
Read and
Write
0x02
0b0XXX XX10
0xF9 STATUS1 STATUS0
1
1
SHMD0
0x03
0b0XXX XX11
ChipID7 ChipID6 ChipID5 ChipID4 ChipID3 ChipID2 ChipID1 ChipID0
Read Only
Read Only
0x0C
0x00
0x40
0x40
0x4D
0x0C
0
0
0
0
1
1
0
1
0x04
0b0XXX XX00
ChipRev7 ChipRev6 ChipRev5 ChipRev4 ChipRev3 ChipRev2 ChipRev1 ChipRev0
0
0
0
0
0
0
0
0
Read and
Write
0xAA
0b10XX XXX0
BRIGHT4
BRIGHT0
0
BRIGHT3 BRIGHT2 BRIGHT1
BRIGHT3 BRIGHT2 BRIGHT1
STATUS1 STATUS0
STATUS1 STATUS0
(MSB)
(LSB)
Read and
Write
0XA9
0b10XX XXX1
BRIGHT4
(MSB)
BRIGHT0
(LSB)
0
0xFE
0b11XX XXX0
MfgID7
0
MfgID6
1
MfgID5
0
MfgID4
0
MfgID3
1
MfgID2
1
MfgID1
0
MfgID0
1
Read Only
Read Only
0xFF
0b11XX XXX1
ChipID7 ChipID6 ChipID5 ChipID4 ChipID3 ChipID2 ChipID1 ChipID0
0
0
0
0
1
1
0
1
*The hexadecimal command byte shown is recommended for maximum forward compatibility with future products.
X = Don’t care.
byte. Immediately after power-up, the data byte returned
by the receive-byte protocol is the inverted contents of
the brightness register, left justified (i.e., BRIGHT4 is in
the most-significant-bit position of the data byte) with
the 3 remaining bits containing a one, STATUS1, and
STATUS0. This gives the same result as using the read-
word protocol with 0b10XXXXXX (0xAA and 0xA9) com-
mand. Use caution with the shorter protocols in multimas-
ter systems, since a second master could overwrite the
command byte without informing the first master. During
shutdown, the serial interface remains fully functional.
SMBus Commands
The MAX8709B registers are accessible through several dif-
ferent redundant commands (i.e., the command byte in the
read-byte and write-byte protocols), which can be used to
read or write the brightness, SHMD, status, or ID registers.
Table 3 summarizes the command byte’s register assign-
ments, as well as each register’s power-on state.
The MAX8709B also supports the receive-byte protocol
for quicker data transfers. This protocol accesses the
register configuration pointed to by the last command
Maxim Integrated
│ 18
www.maximintegrated.com
MAX8709B
High-Efficiency CCFL Backlight
Controller with SMBus Interface
Table 4. SHMD Register Bit Descriptions
POR
BIT NAME
STATE
DESCRIPTION
SHMD2 = 1 forces the lamp off and sets STATUS1. SHMD2 = 0 allows the lamp to operate,
although it may still be shut down by SUS (depending on the state of SHMD1 and SHMD0).
2
1
0
SHMD2
SHMD1
SHMD0
0
0
1
When SUS = 0, this bit has no effect. SUS = 1 and SHMD1 = 1 forces the lamp off and sets STATUS1.
SUS = 1 and SHMD1 = 0 allows the lamp to operate, although it may still be shut down by the SHMD2 bit.
When SUS = 1, this bit has no effect. SUS = 0 and SHMD0 = 1 forces the lamp off and sets STATUS1.
SUS = 0 and SHMD0 = 0 allows the lamp to operate, although it may still be shut down by the SHMD2 bit.
Brightness Register [BRIGHT4 – BRIGHT0]
(POR = 0b10111)
Status Register [STATUS1–STATUS0]
(POR = 0b11)
The 5-bit brightness register corresponds to the 5-bit
brightness code used in dimming control (See the Dimming
Control section). BRIGHT4 - BRIGHT0 = 0b11111 sets
minimum brightness and BRIGHT4 -BRIGHT0 = 0b00000
sets maximum brightness. Note that the brightness-
register polarity of command bytes 0xA9 and 0xAA are
inverted from that of command byte 0x01.
The status register returns information on fault conditions.
If the MAX8709B detects that V
does not exceed 30%
IFB
of V
continuously for 1.22s, the IC latches STATUS1
LOT
to zero. STATUS1 is reset to 1 by toggling SUS or by tog-
gling the input power.
STATUS0 reports 1 as long as no overcurrent conditions
are detected. If an overcurrent condition is detected in any
given DPWM period, STATUS0 is cleared for the duration
of the following DPWM period. If an overcurrent condition
is not detected in any given DPWM period, STATUS0 is
set for the duration of the following DPWM period. Note
that the status-register polarity of command bytes 0xA9
and 0xAA are inverted from that of command byte 0x02.
Shutdown-Mode Register [SHMD2–SHMD0]
(POR = 0b001)
The 3-bit shutdown-mode register configures the opera-
tion of the device when the SUS pin is toggled as
described in Table 4. The shutdown-mode register can
also be used to directly shut off the CCFL regardless of
the state of SUS (Table 5).
ID Registers
The ID registers return information on the manufacturer
chip ID and the chip revision number. The MAX8709B
is the first-generation advanced CCFL controller and its
ChipRev is 0x00. Reading from MfgID register returns
0x4D, which is the ASCII code for M (for Maxim). The
ChipID register returns 0x0D. Writing to these registers
has no effect.
Table 5. SUS and SHMD Register
Truth Table
SUS SHMD2 SHMD1 SHMD0
OPERATING MODE
Operate
0
0
1
1
X
0
0
0
0
1
X
X
0
0
1
Shutdown, STATUS1 set
Operate
X
X
X
1
Shutdown, STATUS1 set
Shutdown, STATUS1 set
X
Table 6. Status-Register Bit Descriptions (Read Only, Writes Have No Effect)
POR
STATE
BIT
NAME
DESCRIPTION
STATUS1 = 0 (or STATUS1 = 1) means that a lamp-out condition has been detected. The
STATUS1 bit stays clear even after the lamp-out condition has gone away. The only way to set
STATUS1 is to shut off the lamp by programming the shutdown-mode register or by toggling SUS.
1
STATUS1
1
STATUS0 = 0 (or STATUS0 = 1) means that an overcurrent condition was detected during the
previous DPWM period. STATUS0 = 1 means that an overcurrent condition was not detected
during the previous DPWM period.
0
STATUS0
1
Maxim Integrated
│ 19
www.maximintegrated.com
MAX8709B
High-Efficiency CCFL Backlight
Controller with SMBus Interface
the half-wave rectified IFB voltage. To set the RMS lamp
current, determine R1 as follows:
Applications Information
To select the correct component values for the MAX8709B,
several CCFL parameters must be specified. (Table 7).
π × 400mV
R1 =
MOSFETs
2 ×I
LAMP(RMS)
The MAX8709B requires four external n-channel power
MOSFETs (NL1, NL2, NH1, and NH2) to form a full-
bridge inverter circuit to drive the transformer primary.
The regulator senses the on-state drain-to-source voltage
of the two low-side MOSFETs NL1 and NL2 to detect the
where I
is the desired RMS lamp current and
LAMP(RMS)
400mV is the typical value of the IFB regulation point
specified in the Electrical Characteristics table. To set
the RMS lamp current to 6mA, the value of R1 should be
148Ω. The closest standard 1% resistors are 147Ω and
150Ω. The precise shape of the lamp-current waveform,
which is dependent on lamp parasitics, influences the
actual RMS lamp current. Use a true RMS current meter
to make final adjustments to R1.
transformer primary current, so the R
of NL1 and
DS(ON)
NL2 should be matched. For instance, if dual MOSFETs
are used to form the full bridge, NL1 and NL2 should be in
one package. Select dual logic-level n-channel MOSFETs
with low R
to minimize conduction loss for NL1/
DS(ON)
NL2 and NH1/NH2. The regulator utilizes the energy
stored in the transformer’s primary leakage inductance to
softly turn on each of four switches in the full bridge ZVS
occurs when the external power MOSFETs are turned on
when their respective drain-to-source voltages are near
0V. ZVS effectively eliminates the instantaneous turn-
Setting the Secondary Voltage Limit
The MAX8709B limits the transformer secondary voltage
during lamp striking and lamp-out faults. The secondary
voltage is sensed through the capacitive voltage-divider
formed by C3 and C4 (Figure 1). The voltage on VFB
is proportional to the CCFL voltage. The selection of
the parallel resonant capacitor C3 is described in the
Transformer Design and Resonant Component Selection
section. C3 is usually between 10pF to 22pF. After the
value of C3 is determined, select C4 using the following
equation to set the desired maximum RMS secondary
on loss of MOSFETs caused by C
(drain-to-source
OSS
capacitance) and parasitic capacitance discharge, and
improves efficiency and reduces switching-related EMI.
Setting the Lamp Current
The MAX8709B senses the lamp current flowing through a
resistor R1 (Figure 1) connected between the low-voltage
terminal of the lamp and ground. The voltage across R1 is
fed to IFB and is internally rectified. The MAX8709B con-
trols the desired lamp current by regulating the average of
voltage V
:
LAMP(RMS)_MAX
2 × V
LAMP(RMS)_MAX
C 4 =
-1 × C3
π × 510mV
where 510mV is the typical value of the VFB regulation
threshold specified in the Electrical Characteristics table.
Table 7. CCFL Specifications
SPECIFICATION
SYMBOL
UNITS
DESCRIPTION
Although CCFLs typically operate at less than 550V
, a higher voltage
RMS
CCFL Minimum
Striking Voltage
(Kick-Off Voltage)
(1000V
and up) is required initially to start the tube. The strike voltage is typically
RMS
V
V
V
STRIKE
RMS
RMS
higher at cold temperatures and at the end of life of the tube. Resonant operation and
the high Q of the resonant tank generate the required strike voltage of the lamp.
Once a CCFL has been struck, the lamp voltage required to maintain light output falls
CCFL Typical
Operating Voltage
(Lamp Voltage)
to approximately 550V
. Short tubes may operate on as little as 250V
. The
RMS
RMS
V
LAMP
operating voltage of the CCFL stays relatively constant, even as the tube’s brightness
is varied.
CCFL Operating
Current
(Lamp Current)
The desired RMS AC current through a CCFL is typically 6mA
allowed through CCFLs. The sense resistor, R1, sets the lamp current.
. DC current is not
RMS
I
mA
RMS
LAMP
CCFL Maximum
Frequency
(Lamp Frequency)
The maximum AC-lamp-current frequency. The circuit should be designed to operate
the lamp below this frequency. The MAX8709B is designed to operate between
20kHz and 100kHz.
f
kHz
Maxim Integrated
│ 20
www.maximintegrated.com
MAX8709B
High-Efficiency CCFL Backlight
Controller with SMBus Interface
If C3 is 15pF, C4 needs to be 21.2nF to set the desired
maximum RMS secondary voltage to 1600V. The closest
standard value of C4 is 22nF.
section, the resonant frequency range is determined by
the transformer secondary leakage inductance L, the
primary series DC-blocking capacitor C2, and the second-
ary parallel resonant capacitor C3. Since it is difficult to
control the transformer leakage inductance, the resonant
tank design should be based on the existing secondary
leakage inductance of the selected CCFL transformer.
The leakage inductance values usually have large toler-
ance and significant variations among different batches.
It is best to work directly with transformer vendors on
leakage inductance requirements. The MAX8709B works
best when the secondary leakage inductance is between
250mH and 350mH. The series capacitor C2 sets the
minimum operating frequency, which is approximately two
times the series resonant peak frequency. Choose:
The resistor R2 is used to set the VFB DC bias point to
0V. Choose the value of R2 as follows:
10
R2 =
2π × f
× C4
SW
where f
is the nominal resonant operating frequency.
SW
Setting the Secondary Current Limit
The MAX8709B limits the secondary current even if the
IFB sense resistor is shorted or transformer secondary
current finds its way to ground without passing through
R1. ISEC monitors the voltage across the sense resistor
R3 connected between the low-voltage terminal of the
transformer secondary winding and ground. Determine
the value of R3 using the following equation:
2
N
C2 ≤
2
2
π × f
×L
MIN
where f
is the minimum operating frequency range.
MIN
Parallel capacitor C3 sets the maximum operating fre-
quency, which is also the parallel resonant peak fre-
quency. Choose:
1.25V
R3 =
2 ×I
SEC(RMS)_MAX
where I
is the desired maximum RMS
C2
SEC(RMS)_MAX
C3 ≥
transformer secondary current during fault conditions,
and 1.25V is the typical value of the ISEC regulation point
specified in the Electrical Characteristics table.
2
2
2
(4π × f
×L × C2) - N
MAX
The transformer core saturation also needs to be consid-
ered when selecting the operating frequency. The primary
winding should have enough turns to prevent transformer
saturation under all operating conditions. Use the follow-
ing expression to calculate the minimum number of turns
(N1) of the primary winding:
Transformer Design and Resonant
Component Selection
The transformer is the most important component of the
resonant tank circuit. The first step in designing the trans-
former is to determine the transformer turns ratio. The
ratio must be high enough to support the CCFL operating
voltage at the minimum supply voltage. The transformer
turns-ratio N can be calculated as follows:
D
× V
IN(MAX)
MAX
N1 >
B
× S × f
MIN
S
where D
is the maximum duty cycle (approximately
0.8) of the high-side switches, V
DC input voltage, B is the saturation flux density of the
MAX
V
LAMP(RMS)
is the maximum
N =
IN(MAX)
0.9 × V
IN(MIN)
S
core, and S is the minimal cross-section area of the core.
where V
is the maximum RMS lamp voltage in
LAMP(RMS)
normal operation, and V
voltage.
is the minimum DC input
Compensation Design
IN(MIN)
The CCI capacitor sets the speed of the current loop that
is used during startup, maintaining lamp current regula-
tion, and during transients caused by changing the input
voltage. The typical CCI value is 0.1μF. Larger values
increase the transient-response delays. Smaller values
speed up transient response, but extremely small values
can cause loop instability.
The next step in the design procedure is to determine
the desired operating frequency range. The MAX8709B
is synchronized to the natural resonant frequency of the
resonant tank. The resonant frequency changes with
operating conditions, such as the input voltage, lamp
impedance, etc. Therefore, the switching frequency var-
ies over a certain range. To ensure reliable operation, the
resonant frequency range must be within the operating
frequency range specified by the CCFL lamp transformer
manufacturers. As discussed in the Resonant Operation
The CCV capacitor sets the speed of the voltage loop that
affects soft-start and soft-stop during DPWM operation,
and voltage loop stability during startup and open-lamp
conditions. The typical CCV capacitor value is 10nF. Use
Maxim Integrated
│ 21
www.maximintegrated.com
MAX8709B
High-Efficiency CCFL Backlight
Controller with SMBus Interface
the smallest value of CCV that gives an acceptable fault
transient response and does not cause excessive ringing
at the beginning of a DPWM pulse.
analog ground is used for REF, CCV, CCI, and ILIM (if
a resistive voltagedivider is used).
3) Route high-speed switching nodes away from sen-
Larger CCV values reduce transient overshoot but can
reduce light output at low-DPWM duty cycles by increas-
ing the time required to reach the tube strike voltage.
sitiveanalog areas (CCI, CCV, REF, V , I , I
,
FB FB SEC
ILIM). Make all pin-strap control input connections
(ILIM, etc.) to analog ground or V rather than power
CC
ground or V
.
DD
Other Components
The external bootstrap circuits formed by D1 and C5/C6
in Figure 1 power the high-side MOSFET drivers. Connect
4) Mount the decoupling capacitor from V
to GND as
CC
close as possible to the IC with dedicated traces that
are not shared with other signal paths.
BST1/BST2 through a signal-level silicon diode to V
,
DD
5) The current-sense paths for LX1 and LX2 to GND
must be made using Kelvin-sense connections to
guarantee the current-limit accuracy. With 8-pin SO
MOSFETs, this is best done by routing power to the
MOSFETs from outside using the top copper layer,
while connecting GND and LX inside (underneath) the
8-pin SO package.
and bypass it to LX1/LX2 with a 0.1μF ceramic capacitor.
Layout Guidelines
Careful PC board layout is critical to achieve stable opera-
tion. The high-voltage section and the switching section
of the circuit require particular attention. The high-voltage
sections of the layout need to be well separated from the
control circuit. Most layouts for singlelamp notebook dis-
plays are constrained to the long and narrow form factor,
so this separation occurs naturally. Follow these guide-
lines for good PC board layout:
6) Ensure the feedback connections are short and direct.
To the extent possible, IFB, VFB, and ISEC connec-
tions should be far away from the high-voltage traces
and the transformer.
1) Keep the high-current paths short and wide, especially
at the ground terminals. This is essential for stable,
jitter-free operation, and high efficiency.
7) To the extent possible, high-voltage trace clearance on
the transformer’s secondary should be widely separat-
ed. The high-voltage traces should also be separated
from adjacent ground planes to prevent lossy capaci-
tive coupling.
2) Utilize a star-ground configuration for power and ana-
log grounds. The power and analog grounds should be
completely isolated—meeting only at the center of the
star. The center should be placed at the exposed back-
side pad to the QFN package. Using separate copper
islands for these grounds may simplify this task. Quiet
8) The traces to the capacitive voltage-divider on the
transformer’s secondary need to be widely separated
to prevent arcing. Moving these traces to opposite
sides of the board can be beneficial in some cases
(see Figure 9).
D1
C4
C2
N1
N2
LAMP
R2
T1
C3
HIGH-CURRENT PRIMARY CONNECTION
HIGH-VOLTAGE SECONDARY CONNECTION
NOTE: DUAL MOSFET N2 IS MOUNTED ON THE BOTTOM SIDE OF THE PC BOARD DIRECTLY UNDER N1.
Figure 9. High-Voltage Components Layout Example
Maxim Integrated
│ 22
www.maximintegrated.com
MAX8709B
High-Efficiency CCFL Backlight
Controller with SMBus Interface
Pin Configuration
Chip Information
PROCESS: BiCMOS
TOP VIEW
28 27 26 25 24 23
22
Package Information
ILIM
REF
LOT
GND
ISEC
SDA
SCL
GH2
LX2
1
2
3
4
5
6
7
21
20
19
18
17
16
For the latest package outline information and land patterns
(footprints), go to www.maximintegrated.com/packages. Note
that a “+”, “#”, or “-” in the package code indicates RoHS status
only. Package drawings may show a different suffix character,
but the drawing pertains to the package regardless of RoHS
status.
BST2
BST1
LX1
MAX8709BETI
LAND
PATTERN
NO.
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE NO.
21-0140
GH1
15 GL1
28 Thin QFN
T2855-6
90-0026
8
9
10 11 12 13 14
THIN QFN
Maxim Integrated
│ 23
www.maximintegrated.com
MAX8709B
High-Efficiency CCFL Backlight
Controller with SMBus Interface
Revision History
REVISION
NUMBER
REVISION
DATE
PAGES
CHANGED
DESCRIPTION
0
1
3/07
Initial release
Removed automotive reference from the Applications
—
10/14
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com.
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses
are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits)
shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
©
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
2014 Maxim Integrated Products, Inc.
│ 24
相关型号：
MAX8709ETI
VACUUM FLUOR DISPLAY DRIVER, QCC28, 5 X 5 MM, 0.80 MM HEIGHT, MO220WHHD-1, TQFN-28
ROCHESTER
MAX8709ETI
Vacuum Fluorescent Driver, 1-Segment, BICMOS, 5 X 5 MM, 0.80 MM HEIGHT, MO220WHHD-1, TQFN-28
MAXIM
MAX8709ETI+
Vacuum Fluorescent Driver, 1-Segment, BICMOS, 5 X 5 MM, 0.80 MM HEIGHT, MO220WHHD, TQFN-28
MAXIM
MAX870EUK+
Switched Capacitor Converter, 0.005A, 194kHz Switching Freq-Max, CMOS, PDSO5, SOT-23, 5 PIN
MAXIM
MAX870EUK-T
Switched Capacitor Converter, 0.005A, 194kHz Switching Freq-Max, CMOS, PDSO5, SOT-23, 5 PIN
MAXIM
©2020 ICPDF网 联系我们和版权申明