MAX98357 [MAXIM]
MAX98357 Development Board/ Evaluation System (WLP);
| 型号： | MAX98357 |
| 厂家： | 
MAXIM INTEGRATED PRODUCTS |
| 描述： | MAX98357 Development Board/ Evaluation System (WLP) |
| 文件： | 总9页 (文件大小：589K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Click here for production status of specific part numbers.
Evaluates: MAX98357A/MAX98357B
(WLP)
MAX98357 Development Board/
Evaluation System (WLP)
General Description
The MAX98357 development board (DEV board) is a fully
Features
● 2.5V to 5.5V Single-Supply Operation
assembled and tested PCB that evaluates the MAX98357
I S digital input Class D power amplifier. The DEV board
● Only a Single External Component (VDD Capacitor)
2
Required in Many Applications
operates from a single 2.5V to 5.5V DC power supply and
is capable of delivering 3.2W into a 4Ω load. The device
outputs can be connected directly to a speaker load for
filterless applications. However, a filter can be added to
2
● I S, Left-Justified, or TDM Input
● Five Selectable Gains (3db, 6dB, 9dB, 12dB, and
15dB)
2
ease evaluation. The MAX98357A accepts standard I S
● Audio Channel Select (Left, Right, and Mono Mix)
● Filterless Operation
data and the MAX98357B accepts left-justified digital
audio data. Both versions also support 8-channel TDM
audio data.
● Optional Class D Output Filters for Ease of
Evaluation
The MAX98357 evaluation system (EV system) includes
the MAX98357 DEV board and Maxim Integrated’s audio
interface board (MAXAUDINT001# board).
● Proven PCB Layout
● Fully Assembled and Tested
The MAXAUDINT001# board provides an easy-to-use
2
USB audio-to-I S converter. This allows for any computer
Ordering Information appears at end of data sheet.
to become a digital audio source, which can be used to
evaluate the devices. The MAXAUDINT001# board can
also be used to power the MAX98357. This allows for a
complete evaluation from a single USB connection.
2.5V TO 5.5V
10µF
0.1µF
VDD
GAIN_SLOT
PCM
MAX98357
LRCLK
AUDIO
BCLK
DIGITAL
OUTP
OUTN
INTERFACE
BOARD
CLASS D
OUTPUT STAGE
AUDIO
INTERFACE
DAC
DIN
SD_MODE
Figure 1. Simplified Block Diagram
19-6833; Rev 2; 9/18
Evaluates: MAX98357A/MAX98357B
(WLP)
MAX98357 Development Board/
Evaluation System (WLP)
Quick Start
Detailed Description of Hardware
The MAX98357 EV system is designed to allow a thor-
Recommended Equipment
2
ough evaluation of the MAX98357 I S digital input Class D
•
•
•
MAX98357 EV system
power amplifier. The DEV board can be used by itself as a
stand-alone evaluation board and driven directly by audio
test equipment. The DEV board can also be used in con-
junction with the MAXAUDINT001# board, which allows for
2.5V to 5.5V, 2A DC power supply
USB audio source (from computer through an audio
®
®
media player such as iTunes or Windows Media
player)
2
any computer to become an I S digital audio source.
The MAXAUDINT001# board has DC regulators that can
be used to power the device. This allows for quick evalu-
ation from a single USB connection. Note that powering
the device from the MAXAUDINT001# board does not
allow for high-power evaluation as the input current is lim-
ited and evaluation with a speaker is not recommended.
Jumpers JU4 and JU6 are used to power the device from
the MAXAUDINT001# board or external supplies con-
nected to test points VIN and VDDIO on the DEV board.
•
4Ω or 8Ω speaker
Procedure
The EV system is fully assembled and tested. Follow the
steps below to verify board operation. Caution: Do not
turn on the power supply until all connections are
completed.
1) Verify that headers and switches are configured as
follows:
The DEV board operates from a single 2.5V to 5.5V DC
power supply and is capable of delivering 3.2W into a 4Ω
load and 1.75W into an 8Ω load. The device outputs can
be connected directly to a speaker for filterless applica-
tions. However, a filter can be added to ease evaluation.
The LRC components needed for evaluation of a filtered
output are included with the EV kit. The MAX98357A
accepts standard I S data and the MAX98357B accepts
left-justified digital audio data. Both versions also support
8-channel TDM audio data.
JU2: Pins 1-3 (selects left channel)
JU4: Pins 1-2 (power routed from the
MAXAUDINT001# board)
JU5: Pins 1-5 (12dB GAIN_SLOT)
J
U6: Pins 2-3 (power routed from external supply)
SW1: Position 1-2 (part is on)
2
2) Set the power-supply output to 5V. Disable the power
supply.
3) Connect the power-supply ground terminal to GND
and the power-supply positive terminal to VIN on the
DEV board.
Filterless Output
The DEV board filterless outputs (OUTP, OUTN) can be
connected directly to a speaker load without any filter-
ing. Use the OUTP and OUTN test points to connect the
speaker directly to the device output.
4) With the audio source disabled, connect the USB
audio source to J1 on the DEV board.
5) Connect the MAXAUDINT001# board to J1 on the DEV
board.
Filtered Output
Audio analyzers typically cannot accept the Class D
amplifier’s pulse-width modulated (PWM) signals at their
inputs. Therefore, the DEV board features optional low-
pass filters at the outputs to ease evaluation. As shipped,
the DEV board’s lowpass filter LRC components are
unpopulated and L1, L2 are shorted on the PCB.
6) Connect the speaker across the OUTP and OUTN test
points.
7) Enable the power-supply output.
8) Enable the audio source.
9) Verify that the speakers are playing the audio source
signal.
To use the filtered output posts (FOUTP, FOUTN), remove
the shorts on L1 and L2 and install components L1, L2, C3–
C7, and R5, R6. Use the output posts to connect the filtered
outputs to the audio analyzer. The default lowpass filters at
the DEV board output are optimized for a 4Ω speaker.
iTunes is a registered trademark of Apple Inc.
Windows Media is registered trademark and registered service
mark of Microsoft Corporation.
Maxim Integrated
│ 2
www.maximintegrated.com
Evaluates: MAX98357A/MAX98357B
(WLP)
MAX98357 Development Board/
Evaluation System (WLP)
SD_MODE Input
EMI Considerations and Optional Ferrite
Bead Filter
The DEV board features a 4-pin jumper (JU2) to control
both the audio channel that is sent to the amplifier output,
along with shutdown mode. JU2 is used to select the
stereo input data between the left channel, right channel,
and the sum of the left/right channels. JU4 must be set to
pins 1-2 and a voltage applied to the +3.3V PCB pad for
proper operation. See Table 2 for shunt positions.
In applications where speaker leads/wires are long
(exceeding approximately 12 inches), additional EMI sup-
pression can be achieved by using a filter constructed from
a ferrite bead (FB1, FB2) and a capacitor to ground (C8,
C9) (Figure 2). Use a ferrite bead with low DC resistance,
high frequency impedance (> 600MHz) between 100Ω
and 600Ω, and rated for at least 1A. The capacitor value
varies based on the ferrite bead chosen and the actual
speaker lead length. Select a capacitor less than 1nF with
the value based upon optimizing EMI performance.
TDM Mode
In TDM mode, the device has a fixed gain of 12dB and the
GAIN_SLOT pin becomes repurposed for slot selection.
The device accepts 8-channel TDM data. The data can
be either 16 bits or 32 bits wide. The GAIN_SLOT pin and
SD_MODE are used to select which of 8 channels of TDM
data the part responds to, as shown in Table 3.
Do not use the optional ferrite bead filter in conjunction
with the optional Class D Filter.
Jumper Selection
Selectable (GAIN_SLOT)
Table 2. JU2 Jumper Selection (SD_MODE)
The DEV board features a 5-pin jumper (JU5) to control
the device’s five programmable gain settings. In TDM
mode, the gain is fixed at 12dB and the GAIN_SLOT pin is
repurposed for slot selection. See Table 1 for gain-control
configuration.
SHUNT
AUDIO
SD_MODE PIN
POSITION
CHANNEL
Connected to VDDIO
through R3 (small resistor)
1-2
Right
Left
Connected to VDDIO
through a 2kΩ resistor
1-3*
Connected to VDDIO
through R4 (large resistor)
Mono mix
(left + right)/2
OUTP
1-4
MAX98357A
MAX98357B
OUTN
*Default position.
Table 3. TDM Mode Channel Selection
(JU2, JU5)
Figure 2. Optional Ferrite Bead Filter
JU2
JU5
X
CHANNEL
BITS
Table 1. JU5 Jumper Selection
(GAIN_SLOT)
Connected low
OFF
0
N/A
1-3
1-3
1-3
1-3
1-3
1-4
1-4
1-4
1-5
16 or 32
16 or 32
16 or 32
16 or 32
16 or 32
16 or 32
16 or 32
16 or 32
SHUNT
POSITION
GAIN_SLOT
PIN
MAXIMUM
1-3
1
GAIN_SLOT (dB)
OPEN
1-2
2
Connected to VDD
through 100kΩ resistor R1
1-2
1-3
3
6
3
1-4
4
Connected to VDD
1-5
5
Connected to GND
through 100kΩ resistor R2
1-4
15
12
9
OPEN
1-3
6
7
1-5*
Connected to GND
Not
installed
Unconnected
*Default position.
Maxim Integrated
│ 3
www.maximintegrated.com
Evaluates: MAX98357A/MAX98357B
(WLP)
MAX98357 Development Board/
Evaluation System (WLP)
2
Shutdown Mode
Driving I S Directly
2
The device features a low-power shutdown mode that is
activated by setting jumper SW1 to pins 2-3. To exit shut-
down mode, set SW1 to pins 1-2 and select the desired
stereo input channel using jumper JU2. See Table 4 for
shunt positions.
To drive I S directly, apply signals at the BCLK, LRCLK,
and SDIN test points, or on the J3 header, or between J3
pins 1-2 at the appropriate locations (signal and ground
are labeled on the board).
Evaluating the MAX98357B
External/Internal VDDIO (+1.8V to +3.3V)
The MAX98357 DEV board comes with a MAX98357A
populated on the board, but can also be used to evaluate
the MAX98357B. To evaluate the MAX98357B, carefully
remove the MAX98357A (U1) device from the board and
replace with the MAX98357BEWL+. No other component
changes are required.
On the DEV board, a logic voltage from a control interface
is needed for proper selection of the stereo input channel
through SD_MODE. This voltage can be applied exter-
nally at the VDDIO test point or it can be provided from
circuitry on the MAXAUDINT001# board. See Table 5 for
JU4 jumper selection.
Table 4. SW1 Jumper Selection
Other logic voltages can be used other than +3.3V. If you
want to use other logic voltages, resistors R3 and R4
must be adjusted. Refer to the SD_MODE and Shutdown
Operation section in the MAX98357 IC data sheet for
more information.
SWITCH
VDDIO
DEVICE
POSITION
VOLTAGE
OPERATION
VDDIO determined
by JU4 jumper
position
Normal
(input channel selected
through JU2 setting)
1-2*
VDD Input Supply (+2.5V to +5.5V)
The device can accept an input supply from +2.5V to
+5.5V. This voltage can be applied externally at the
VDD and GND PCB pads, or it can be provided from the
MAXAUDINT001# board. See Table 6 for JU6 jumper
selection.
2-3
Connected to GND
Shutdown
*Default position.
Table 5. JU4 Jumper Selection (VDDIO)
SHUNT
LOGIC VOLTAGE (VDDIO)
POSITION
Audio Interface Board
(MAXAUDINT001# Board)
3.3V supplied by the MAXAUDINT001#
board connected to J1 header.
2
The MAXAUDINT001# board provides USB-to-I S data
conversion, as well as DC regulators that can be used
to power the devices. The USB-to-I S converter on the
1-2*
User-supplied external power supply applied
at the VDDIO test point.
2
2-3
MAXAUDINT001# board allows for any computer to
2
become an I S digital audio source without requiring
*Default position.
additional driver installation. On the MAXAUDINT001#
board, set SW1 to “demo” and set the I S switch to con-
2
Table 6. JU6 Jumper Selection (VDD)
nected to source audio by USB. This allows for a quick
evaluation from a single USB connection. Using the
MAXAUDINT001# board as a power supply for high-pow-
er evaluation is not recommended as the input current is
limited. For high-power evaluation, use an external supply
connected to VIN.
SHUNT
INPUT VOLTAGE (VDD)
POSITION
VDD supplied from the MAXAUDINT001#
board connected to the J1 header.
1-2*
User-supplied external power supply applied
at the VIN PCB pad.
2-3
*Default position.
Maxim Integrated
│ 4
www.maximintegrated.com
Evaluates: MAX98357A/MAX98357B
(WLP)
MAX98357 Development Board/
Evaluation System (WLP)
Component List
DESIGNATION
QTY
DESCRIPTION
DESIGNATION
R4
QTY
DESCRIPTION
1
0
3
634kΩ ±1% resistor (0603)
Not installed, resistors (0402)
0Ω ±5% resistors (0603)
BCLK, DIN,
LRCLK
Orange multipurpose test
points
3
R5, R6
10µF ±10%, 6.3V X5R
R7–R9
C1
C2
1
1
ceramic capacitor (0603)
Murata GRM188R60J106K
I2S input Class D audio
amplifier (16 WLP)
Maxim MAX98357AEWL+
U1
1
1
0.1µF ±10%, 16V X7R
ceramic capacitor (0402)
Murata GRM155R71C104K
Red multipurpose test point
(63 mil drill size)
VDDIO
Not installed, ceramic
capacitors (0402)
SPDT jumper switch, 0.1in
centers
C3–C12
0
2
4
SW1
—
1
4
FB1, FB2
0Ω ±5% resistors (0603)
Shunts
FOUTN, FOUTP,
GND, VIN
PCB: MAX98357 WLP
EVKIT DEVELOPMENT
BOARD
Binding posts
—
1
20G plated solid copper bus
wire, 0.25in U-shaped wire
loop
FOUTN, FOUTP,
GND (x2), VDD
5
OPTIONAL CLASS D FILTER COMPONENTS
0.22µF ±10%, 6.3V X5R
Black multipurpose test points
(63 mil drill size)
C3–C7
7
ceramic capacitors (0402)
TDK C1005X5R0J224K
GND (x4), OUTN
J1
5
1
26-pin (2 x 13) dual-row right-
angle header, 0.1in centers
22µH, 1A inductors
(6.2mm x 6.3mm)
TOKO A916CY-220M
L1, L2
2
2
J3
JU2
1
1
2
1
6-pin header
4-pin header, 0.1 in centers
3-pin headers, 0.1 in centers
5-pin header, 0.1 in centers
R5, R6
22Ω ±5% resistors (0402)
JU4, JU6
JU5
2
OPTIONAL I S CONDITIONING COMPONENTS
R7–R9
3
51Ω ±5% resistors (0402)
Not installed, 22µH inductors
(6.2mm x 6.3mm)—short
(PC trace)
TOKO D63CB series part
TOKO A916CY-220M
18pF ±5%, 50V, C0G ceramic
capacitors (0402)
C10-C12
3
L1, L2
0
OPTIONAL EMI FILTERING COMPONENTS
680pF ±10% 50V X54 ceramic
C8, C9
2
2
capacitors (0402) TDK
CGA2B1C0G2A681J050BE
White multipurpose test point
(63 mil drill size)
OUTP
1
Murata BLM18SG331TN1
(0603)
R1, R2
R3
2
1
100kΩ ±5% resistors (0603)
226kΩ ±1% resistor (0603)
FB1, FB2
Component Suppliers
SUPPLIER
Murata Americas
PHONE
WEBSITE
770-436-1300
847-803-6100
847-297-0070
www.murataamericas.com
www.component.tdk.com
www.tokoam.com
TDK Corp.
TOKO America, Inc.
Note: Indicate that you are using the MAX98357 when contacting these component suppliers.
Maxim Integrated
│ 5
www.maximintegrated.com
Evaluates: MAX98357A/MAX98357B
(WLP)
MAX98357 Development Board/
Evaluation System (WLP)
Figure 3. MAX98357 DEV Board Schematic
Maxim Integrated
│ 6
www.maximintegrated.com
Evaluates: MAX98357A/MAX98357B
(WLP)
MAX98357 Development Board/
Evaluation System (WLP)
MAX98357 EV Kit PCB Layouts
1.0”
1.0”
MAX98357 DEV Board Silkscreen—Top
MAX98357 DEV Board PCB Layout—Component Side
1.0”
MAX98357 DEV Board PCB Layout—Layer 2
Maxim Integrated
│ 7
www.maximintegrated.com
MAX98357 EV Kit PCB Layouts (continued)
Evaluates: MAX98357A/MAX98357B
(WLP)
MAX98357 Development Board/
Evaluation System (WLP)
MAX98357 EV Kit PCB Layouts (continued)
1.0”
MAX98357 DEV Board PCB Layout—Layer 3
MAX98357 DEV Board PCB Layout—Solder Side
Ordering Information
PART
TYPE
Development Board
(DEV Board only)
MAX98357DEV#WLP
Evaluation System Kit
(DEV + MAXAUDINT001#
Boards)
MAX98357EVSYS#WLP
#Denotes RoHS compliant.
Maxim Integrated
│ 8
www.maximintegrated.com
Evaluates: MAX98357A/MAX98357B
(WLP)
MAX98357 Development Board/
Evaluation System (WLP)
Revision History
REVISION REVISION
PAGES
CHANGED
DESCRIPTION
NUMBER
DATE
10/13
4/14
0
1
Initial release
—
Added Evaluating the MAX98357B section and updated Figures 2 and 7
4–6, 8
Changed all instances of “AUDINT001” to “MAXAUDINT001#,” added EMI filtering
information and new Figure 2, updated Component List table
2
9/18
1–9
For pricing, delivery, and ordering information, please visit Maxim Integrated’s online storefront at https://www.maximintegrated.com/en/storefront/storefront.html.
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses
are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time.
©
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
2018 Maxim Integrated Products, Inc.
│ 9
相关型号：
©2020 ICPDF网 联系我们和版权申明