MTD6505T-SSE/NA [MICROCHIP]
Brushless DC Motor Controller, 1A, PDSO10;型号: | MTD6505T-SSE/NA |
厂家: | MICROCHIP |
描述: | Brushless DC Motor Controller, 1A, PDSO10 电动机控制 光电二极管 |
文件: | 总22页 (文件大小:1723K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MTD6505
3-Phase Sinusoidal Sensorless Brushless Motor Driver
Features
Description
• 180° Sinusoidal Drive for High Efficiency and Low
Acoustic Noise
The MTD6505 device is a 3-phase, full-wave
sensorless driver for brushless DC (BLDC) motors. It
features 180° sinusoidal drive, high-torque output and
silent drive. With the adaptive features, parameters and
wide range of power supplies (2V to 5.5V), the
MTD6505 is intended to cover a broad range of motor
characteristics, while requiring minimum external
components. Speed control can be achieved through
either PSM or PWM.
• Position Sensorless BLDC Drivers
(no Hall Effect Sensor required)
• Integrated Power Transistors
• Supports 2V to 5.5V Power Supplies
• Programming Resistor (RPROG) Settings to Fit
Motor Constant (KM) Range from 3.25 mV/Hz to
52 mV/Hz
The compact packaging and the minimal bill of
materials make the MTD6505 device extremely
cost-efficient in fan applications. For example, the CPU
cooling fans in notebook computers require designs
that provide low acoustic noise, low mechanical
vibration, and are highly efficient. The frequency
generator (FG) output enables precision speed control
in closed-loop applications.
• Direction Control:
- Forward direction: connect DIR pin to GND or
leave floating
- Reverse direction: connect DIR pin to VBIAS
or 3V
• Speed Control through Power Supply Modulation
(PSM) and/or Pulse-Width Modulation (PWM)
• Built-in Frequency Generator (FG Output Signal)
The MTD6505 device includes Lockup Protection mode
to turn off the output current when the motor is in a lock
condition, with an automatic recovery feature to restart
the fan when the lock condition is removed. Motor
overcurrent limitation and thermal shutdown protection
are included for safety-enhanced operations.
• Built-in Lockup Protection and Automatic
Recovery Circuit
• Built-in Overcurrent Limitation
• Built-in Thermal Shutdown Protection
• Built-in Overvoltage Protection
• No External Tuning Required
• Available Package:
The MTD6505 is available in a compact, thermally-
enhanced, 10-lead 3 mm x 3 mm UDFN package.
10-Lead 3mm x 3mm UDFN
Package Types
Applications
MTD6505
3x3 UDFN*
• Notebook CPU Cooling Fans
• 5V 3-Phase BLDC
1
2
3
4
5
10
9
FG
RPROG
VBIAS
PWM
DIR
EP
11
VDD
8
OUT1
OUT2
OUT3
7
6
GND
*Includes Exposed Thermal Pad (EP); see Table 3-1.
2011-2014 Microchip Technology Inc.
DS20002281C-page 1
MTD6505
Functional Block Diagram
VBIAS
VDD
FG
VDD
OUT3
OUT2
OUT1
CPU + Peripherals
PWM
DIR
GND
Thermal
Protection
Short-Circuit
Protection
Nonvolatile
Memory
Motor Phase
Detection
Circuit
Overcurrent
Protection
Adjustable
KM
RPROG
RPROG Sense
DS20002281C-page 2
2011-2014 Microchip Technology Inc.
MTD6505
Typical Application
VDD
R1
KM0 KM1, 2
KM3
VBIAS VBIAS
FG
10 PWM
1
2
3
4
5
R2
RPROG
VBIAS
DIR
9
VDD
C1
VDD
8
OUT1
OUT2
OUT3
7
C2
GND
6
Recommended External Components for Typical Application
Element
Type/Value
Comment
C1
C2
R1
R2
1 µF
1 µF
Connect as close as possible to IC input pins
Connect as close as possible to IC input pins
Connect to VLOGIC on microcontroller side (FG Pull-Up)
10 kΩ
3.9 kΩ or 24 kΩ
Select appropriate programming resistor value, see
Table 4-2
2011-2014 Microchip Technology Inc.
DS20002281C-page 3
MTD6505
NOTES:
DS20002281C-page 4
2011-2014 Microchip Technology Inc.
MTD6505
† Notice: Stresses above those listed under “Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only and functional operation of
the device at those or any other conditions above those
indicated in the operational listings of this specification
is not implied. Exposure to maximum rating conditions
for extended periods may affect device reliability.
1.0
ELECTRICAL
CHARACTERISTICS
Absolute Maximum Ratings†
Power Supply Voltage (V
) ...................... -0.7 to +7.0V
DD_MAX
Maximum Output Voltage (V
)............... -0.7 to +7.0V
)....................1000 mA
OUT_MAX
(1)
Maximum Output Current (I
FG Maximum Output Voltage (V
Note 1: IOUT is also internally limited, according
to the limits defined in the “Electrical
Characteristics” table.
OUT_MAX
) ........... -0.7 to +7.0V
FG_MAX
FG Maximum Output Current (I
) ......................5.0 mA
FG_MAX
V
Maximum Voltage (V
) ................ -0.7 to +4.0V
) ................ -0.7 to +7.0V
2: Reference Printed Circuit Board (PCB),
according to JEDEC standard EIA/JESD
51-9.
BIAS
BIAS_MAX
PWM Maximum Voltage (V
PWM_MAX
(2)
Allowable Power Dissipation (P
).........................1.5W
D_MAX
Maximum Junction Temperature (T )..........................+150°C
J
ESD protection on all pins2 kV
ELECTRICAL CHARACTERISTICS
Electrical Specifications: Unless otherwise specified, all limits are established for VDD = 2.0V to 5.5V, TA = +25°C
Parameters
Sym.
Min.
Typ.
Max.
Units
Conditions
Power Supply Voltage
Power Supply Current
Standby Current
VDD
IVDD
2
—
5
5.5
10
40
V
—
—
mA
µA
VDD = 5V
IVDD_STB
30
PWM = 0V, VDD = 5V
(Standby mode)
OUTX
High Resistance
RON(H)
RON(L)
RON(H+L)
VBIAS
—
—
—
0.75
0.75
1.5
1.1
1.3
2.4
Ω
Ω
Ω
IOUT = 0.5A, VDD = 5V
Note 1
OUTX
Low Resistance
IOUT = 0.5A, VDD = 5V
Note 1
OUTX
Total Resistance
IOUT = 0.5A, VDD = 5V
Note 1
VBIAS Internal
Supply Voltage
—
3
VDD – 0.2
—
—
—
V
V
VDD = 3.2V to 5.5V
VDD < 3.2V
—
PWM Input Frequency
PWM Input H Level
PWM Input L Level
fPWM
1
100
kHz
V
VPWM_H
VPWM_L
RPWM_0
0.55 VDD
—
VDD
VDD 4.5V
VDD 4.5V
PWM = 0V
0
—
0.2 VDD
—
V
PWM Internal Pull-Up
Resistor
—
266
kΩ
PWM Internal Pull-Up
Resistor
RPWM
—
133
—
kΩ
PWM duty-cycle > 0%
DIR Input H Level
DIR Input L Level
VDIR_H
VDIR_L
RDIR
VBIAS – 0.5
—
—
—
VBIAS
0.2 VDD
200
V
V
VDD 4.5V
VDD 4.5V
0
DIR Internal Pull-Down
Resistor
100
kΩ
FG Output Pin Low-
Level Voltage
VOL_FG
ILH_FG
TRUN
—
– 10
—
—
—
0.5
5
0.25
10
V
µA
s
IFG = -1 mA
VFG = 5.5V
FG Output Pin Leakage
Current
Lock Protection
Operating Time
—
Lock Protection Waiting
Time
TWAIT
4.5
5.5
s
Note 2
Note 3
Overcurrent Protection
Overvoltage Protection
IOC_MOT
VOV
—
—
750
7.2
—
—
mA
V
2011-2014 Microchip Technology Inc.
DS20002281C-page 5
MTD6505
ELECTRICAL CHARACTERISTICS (CONTINUED)
Electrical Specifications: Unless otherwise specified, all limits are established for VDD = 2.0V to 5.5V, TA = +25°C
Parameters
Sym.
Min.
Typ.
Max.
Units
Conditions
Short Protection on
High Side
IOC_SW_H
—
2.57
—
A
Short Protection on
Low Side
IOC_SW_L
—
-2.83
—
A
Thermal Shutdown
TSD
—
—
170
25
—
—
°C
°C
Thermal Shutdown
Hysteresis
TSD_HYS
Note 1: Minimum and maximum parameters are not production tested and are specified by design and validation.
2: Related to the internal oscillator frequency (see Figure 2-1).
3: 750 mA is the standard option for MTD6505. Additional overcurrent protection levels are available upon
request. Please contact factory for different overcurrent protection values.
TEMPERATURE SPECIFICATIONS
Electrical Specifications: Unless otherwise specified, all limits are established for VDD = 2.0V to 5.5V, TA = +25°C.
Parameters
Sym.
Min.
Typ.
Max.
Units
Conditions
Temperature Ranges
Operating Temperature
TOPR
TSTG
-40
-55
—
—
+125
+150
°C
°C
Storage Temperature Range
Thermal Package Resistances
Thermal Resistance, 10LD-UDFN 3x3
JA
JC
—
—
96.6
12
—
—
°C/W
°C/W
DS20002281C-page 6
2011-2014 Microchip Technology Inc.
MTD6505
2.0
TYPICAL PERFORMANCE CURVES
Note:
The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
Note: Unless indicated, TA = +25°C, VDD = 2.0V to 5.5V, OUT1, 2, 3 and PWM open.
2.5
2
1
0.5
0
VDD = 5.5V
VDD=5.5V
VDD = 2V
V
DD = 2V
-0.5
-1
1.5
1
-1.5
-2
-2.5
-3
-3.5
-4
0.5
0
-4.5
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
FIGURE 2-1:
Oscillator Frequency
FIGURE 2-4:
Inputs (PWM, DIR) VIL vs.
Deviation vs. Temperature.
Temperature.
3
2.5
2
3.14
3.12
3.1
VDD = 5.5V
3.08
3.06
3.04
3.02
3
1.5
1
VDD = 2V
0.5
0
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
FIGURE 2-2:
Internal Regulated Voltage
FIGURE 2-5:
Inputs (PWM, DIR) VIH vs.
(VBIAS) vs. Temperature.
Temperature.
3.5
3
6
5.5
5
4.5
4
V
DD = 2V
2.5
2
3.5
3
1.5
1
2.5
2
1.5
1
VDD = 5.5V
0.5
0
0.5
0
-40 -25 -10
5
20 35 50 65 80 95 110 125
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
Temperature (°C)
VDD (V)
FIGURE 2-3:
Internal Regulated Voltage
FIGURE 2-6:
Outputs RON High-Side
(VBIAS) vs. Supply Voltage (VDD).
Resistance vs. Temperature.
2011-2014 Microchip Technology Inc.
DS20002281C-page 7
MTD6505
Note: Unless indicated, TA = +25°C, VDD = 2.0V to 5.5V, OUT1, 2, 3 and PWM open.
6
5.5
5
0
-5
VDD = 2V
4.5
4
-10
-15
-20
-25
-30
-35
-40
3.5
3
2.5
2
VDD = 2V
1.5
1
VDD = 5.5V
VDD = 5.5V
0.5
0
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
FIGURE 2-7:
Outputs RON Low-Side
FIGURE 2-10:
PWM Pull-Up Current vs.
Resistance vs. Temperature.
Temperature.
7
6
VDD = 5.5V
5
4
VDD = 2V
3
2
1
0
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
FIGURE 2-8:
Supply Current vs.
FIGURE 2-11:
Typical Output on Start-Up.
Temperature.
60
50
40
30
20
10
0
VDD = 5.5V
VDD = 2V
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
FIGURE 2-12:
Typical Outputs on Closed
FIGURE 2-9:
Standby Current vs.
Loop.
Temperature.
DS20002281C-page 8
2011-2014 Microchip Technology Inc.
MTD6505
3.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 3-1.
TABLE 3-1:
MTD6505 PIN FUNCTION TABLE
Pin
Number
Type
Name
Function
1
2
3
4
5
6
7
8
9
O
I
FG
Motor Speed Indication Output Pin
RPROG KM Parameter Setting with External Resistors Pin, see Table 4-2 for values
—
O
O
—
O
—
I
VBIAS
OUT1
OUT2
GND
OUT3
VDD
Internal Regulator Output Pin (for decoupling only)
Single-Phase Coil Output Pin
Single-Phase Coil Output Pin
Negative Voltage Supply Pin (ground)
Single-Phase Coil Output Pin
Positive Voltage Supply Pin for Motor Driver
DIR
Motor Rotation Direction Pin
- Forward direction: connect this pin to GND or leave floating
- Reverse direction: connect this pin to VBIAS
10
11
I
PWM
EP
PWM Input Signal Pin for Speed Control
—
Exposed Thermal Pad Pin (Connect to the ground plan for better thermal
dissipation)
Legend: I = Input; O = Output
2011-2014 Microchip Technology Inc.
DS20002281C-page 9
MTD6505
NOTES:
DS20002281C-page 10
2011-2014 Microchip Technology Inc.
MTD6505
4.3
Frequency Generator Function
4.0
FUNCTIONAL DESCRIPTION
The Frequency Generator output (FG) is a “Hall Effect
Sensor equivalent” digital output, giving information to
an external controller about the speed and phase of the
motor. The FG pin is an open-drain output, connecting
to a logical voltage level through an external pull-up
resistor. When a lock or an out-of-sync situation is
detected by the driver, this output is set to
high-impedance until the motor is restarted. Leave the
pin open when it is not used.
The MTD6505 generates a full-wave signal to drive a
3-phase BLDC motor. High efficiency and low power
consumption are achieved due to CMOS transistors
and synchronous rectification drive type.
4.1
Speed Control
The rotational speed of the motor can be controlled
either through the PWM digital input signal or by acting
directly on the power supply (VDD). When the PWM
signal is High (or left open), the motor rotates at full
speed. When the PWM signal is low, the IC outputs are
set to high-impedance and the motor is stopped.
4.4
Lock-Up Protection and Automatic
Restart
If the motor is blocked and cannot rotate freely, a
lock-up protection circuit detects it and disables the
driver by setting its outputs to high-impedance to
prevent the motor coil from burnout. After a “waiting
time” (TWAIT), the lock-up protection is released and
normal operation resumes for a given time (TRUN). If
the motor is still blocked, a new period of waiting time
is started. TWAIT and TRUN timings are fixed internally,
so that no external capacitor is required.
By changing the PWM duty cycle, the speed can be
adjusted. Thus, the user has freedom to choose the
PWM system frequency within a wide range (from
1 kHz to 100 kHz).
Since the PWM pin has an internal pull-up resistor
connected to VDD, it is recommended to drive it
between 0V and high Z. The PWM driver must be able
to support the pull-up resistor current to drive the pin.
See “PWM Internal Pull-Up Resistor” in Section 1.0,
Electrical Characteristics.
4.5
Overcurrent Protection
The output transistor activation always occurs at a fixed
rate of 30 kHz, which is outside the range of audible
frequencies.
The motor peak current is limited by the driver to
750 mA (standard value), thus limiting the maximum
power dissipation in the coils.
Note 1: The PWM frequency has no direct effect
on the motor speed and is asynchronous
with the activation of the output transistors.
4.6
Thermal Shutdown
The MTD6505 device has a thermal protection function
which detects when the die temperature exceeds
TJ = +170°C. When this temperature is reached, the
circuit enters Thermal Shutdown mode, and outputs
OUT1, OUT2 and OUT3 are disabled (high-imped-
ance), avoiding IC destruction and allowing the circuit
to cool down. When the junction temperature (TJ) drops
below +145°C, normal operation resumes.
2: The standard output frequency is 30 kHz.
A 20 kHz output frequency option is
available upon request.
4.2
Motor Rotation Direction
The current-carrying order of the outputs depends on
the DIR pin state (“Rotation Direction”) and is illustrated
in Table 4-1. The DIR pin is not designed for dynamic
direction change during operation.
The thermal detection circuit has +25°C hysteresis.
Thermal shutdown
TABLE 4-1:
MOTOR ROTATION
DIRECTION OPTIONS
(DIR PIN)
Normal
operation
Rotation
Direction
Outputs Activation
Sequence
DIR Pin State
TJ
Connected
to GND
Forward OUT1 OUT2 OUT3
+145°
+170°
or Floating
FIGURE 4-1:
Hysteresis.
Thermal Protection
Connected
to VBIAS
Reverse OUT3 OUT2 OUT1
2011-2014 Microchip Technology Inc.
DS20002281C-page 11
MTD6505
4.7
Overvoltage Shutdown
4.10 Defining the Correct R
Value
PROG
The MTD6505 device has an overvoltage protection
function which detects when the VDD voltage exceeds
VOV = +7.2V. When this temperature is reached, the
circuit enters Thermal Shutdown mode and outputs
OUT1, OUT2 and OUT3 are disabled
This section explains how to define the correct KM
value for a specific fan. The KM is linked to the RPROG
(see Table 4-2). An incorrect KM selection can create
issues or reduce efficiency.
(high-impedance).
4.10.1
OPERATION
Follow the next steps to define the right RPROG value:
4.8
Internal Voltage Regulator
1. Apply a constant stream of air to a fan that is not
connected.
VBIAS voltage is generated internally and is used to
supply internal logical blocks. The VBIAS pin is used to
connect an external decoupling capacitor (1 µF or
higher). Notice that this pin is for IC internal use, and is
not designed to supply DC current to external blocks.
2. Using an oscilloscope, measure the waveform
between two phases when the fan is rotating.
3. Measure the generated peak-to-peak voltage
(VP-P) value and the frequency (f).
4. Compute KM based on the measured VP-P and
f (in mV/Hz):
4.9
Back Electromotive Force (BEMF)
Coefficient Setting
KM is the electro-mechanical coupling coefficient of the
motor (also referred to as “motor constant” or “BEMF
constant”). Depending on the conventions in use, the
exact definition of KM and its measurement criteria can
vary among motor manufacturers. To accommodate
various motor applications, the MTD6505 provides
options to facilitate diverse BEMF coefficients.
EQUATION 4-1:
KM COMPUTE
VP – P
K
= -------------
M
2f
KM should be constant for all fan rotation speeds; but,
for the KM measurement, the fan rotation speed (due to
the air stream) should be close to nominal.
The MTD6505 defines BEMF coefficient (KM) as the
peak value of the phase-to-phase BEMF voltage,
normalized to the electrical speed of the motor. The
following table offers methods to set the KM value for
the MTD6505 device.
Note:
This is a theoretical procedure that does
not take care of the harmonics generated
by the BEMF. This information has to be
taken for indication only.
TABLE 4-2:
KM SETTINGS
KM (mV/Hz) Range
Phase-to-Phase
KM
Option
RPROG
Min.
Max.
KM0
KM1
KM2
KM3
3.25
6.5
13
6.5
13
26
52
GND
24 k
3.9 k
VBIAS
26
The RPROG sensing is actually a sequence that is
controlled by the firmware. For any given RPROG, the
internal control block will output the corresponding KM
range.
DS20002281C-page 12
2011-2014 Microchip Technology Inc.
MTD6505
5.0
5.1
PACKAGING INFORMATION
Package Marking Information
10-Lead UDFN (3x3x0.5 mm)
Example
AAAD
1441
256
Device
Code
MTD6505T-E/NA
AAAD
Legend: XX...X Customer-specific information
Y
Year code (last digit of calendar year)
YY
Year code (last 2 digits of calendar year)
WW
NNN
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
Pb-free JEDEC® designator for Matte Tin (Sn)
This package is Pb-free. The Pb-free JEDEC designator (
can be found on the outer packaging for this package.
e
3
*
)
e
3
Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over
to the next line, thus limiting the number of available characters for customer-specific
information.
2011-2014 Microchip Technology Inc.
DS20002281C-page 13
MTD6505
DS20002281C-page 14
2011-2014 Microchip Technology Inc.
MTD6505
2011-2014 Microchip Technology Inc.
DS20002281C-page 15
MTD6505
DS20002281C-page 16
2011-2014 Microchip Technology Inc.
MTD6505
APPENDIX A: REVISION HISTORY
Revision C (December 2014)
The following is the list of modifications:
1. Changed the title of the document.
2. Changed the minimum and maximum values for
DIR Input H Level in the Electrical Characteris-
tics table.
3. Updated Section 4.0 “Functional Descrip-
tion”. Added new Section 4.7 “Overvoltage
Shutdown”.
4. Minor editorial corrections.
Revision B (October 2013)
The following is the list of modifications:
1. Updated the Absolute Maximum Ratings†
section with the correct VBIAS parameter.
2. Updated the Thermal Resistance values in the
Temperature Specifications table.
3. Added Figure 2-11 and Figure 2-12.
4. Added Section 4.10 “Defining the Correct
RPROG Value”.
5. Minor grammatical and editorial corrections.
Revision A (November 2011)
• This is the original release of this document.
2011-2014 Microchip Technology Inc.
DS20002281C-page 17
MTD6505
NOTES:
DS20002281C-page 18
2011-2014 Microchip Technology Inc.
MTD6505
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO.
Device
T
-X
/XX
Examples:
a) MTD6505T-E/NA Tape and Reel,
Tape & Reel Temperature Package
Extended Temperature
10-Lead UDFN Package
Device:
MTD6505T: 3-Phase Sinusoidal Sensorless Brushless
Motor Driver (Tape and Reel)
Temperature Range:
Package:
E
=
=
Extended -40°C to +125°C
NA
Plastic Dual Flat, thermally-enhanced,
3x3x0.5 mm Body (UDFN)
2011-2014 Microchip Technology Inc.
DS20002281C-page 19
MTD6505
NOTES:
DS20002281C-page 20
2011-2014 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC,
FlashFlex, flexPWR, JukeBlox, KEELOQ, KEELOQ logo, Kleer,
LANCheck, MediaLB, MOST, MOST logo, MPLAB,
32
OptoLyzer, PIC, PICSTART, PIC logo, RightTouch, SpyNIC,
SST, SST Logo, SuperFlash and UNI/O are registered
trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
The Embedded Control Solutions Company and mTouch are
registered trademarks of Microchip Technology Incorporated
in the U.S.A.
Analog-for-the-Digital Age, BodyCom, chipKIT, chipKIT logo,
CodeGuard, dsPICDEM, dsPICDEM.net, ECAN, In-Circuit
Serial Programming, ICSP, Inter-Chip Connectivity, KleerNet,
KleerNet logo, MiWi, MPASM, MPF, MPLAB Certified logo,
MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code
Generation, PICDEM, PICDEM.net, PICkit, PICtail,
RightTouch logo, REAL ICE, SQI, Serial Quad I/O, Total
Endurance, TSHARC, USBCheck, VariSense, ViewSpan,
WiperLock, Wireless DNA, and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
Silicon Storage Technology is a registered trademark of
Microchip Technology Inc. in other countries.
GestIC is a registered trademarks of Microchip Technology
Germany II GmbH & Co. KG, a subsidiary of Microchip
Technology Inc., in other countries.
All other trademarks mentioned herein are property of their
respective companies.
© 2011-2014, Microchip Technology Incorporated, Printed in
the U.S.A., All Rights Reserved.
ISBN: 978-1-63276-918-3
QUALITY MANAGEMENT SYSTEM
CERTIFIED BY DNV
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
== ISO/TS 16949 ==
2011-2014 Microchip Technology Inc.
DS20002281C-page 21
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2943-5100
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4123
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
India - Pune
Tel: 91-20-3019-1500
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
Web Address:
www.microchip.com
Japan - Osaka
Tel: 81-6-6152-7160
Fax: 81-6-6152-9310
Germany - Dusseldorf
Tel: 49-2129-3766400
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
China - Beijing
Tel: 86-10-8569-7000
Fax: 86-10-8528-2104
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Japan - Tokyo
Tel: 81-3-6880- 3770
Fax: 81-3-6880-3771
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
Austin, TX
Tel: 512-257-3370
Germany - Pforzheim
Tel: 49-7231-424750
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
Boston
China - Chongqing
Tel: 86-23-8980-9588
Fax: 86-23-8980-9500
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
China - Hangzhou
Tel: 86-571-8792-8115
Fax: 86-571-8792-8116
Italy - Venice
Tel: 39-049-7625286
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
China - Hong Kong SAR
Tel: 852-2943-5100
Fax: 852-2401-3431
Cleveland
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
Poland - Warsaw
Tel: 48-22-3325737
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Sweden - Stockholm
Tel: 46-8-5090-4654
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
Detroit
Novi, MI
Tel: 248-848-4000
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
UK - Wokingham
Tel: 44-118-921-5800
Fax: 44-118-921-5820
Taiwan - Hsin Chu
Tel: 886-3-5778-366
Fax: 886-3-5770-955
Houston, TX
Tel: 281-894-5983
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Taiwan - Kaohsiung
Tel: 886-7-213-7830
China - Shenzhen
Tel: 86-755-8864-2200
Fax: 86-755-8203-1760
Taiwan - Taipei
Tel: 886-2-2508-8600
Fax: 886-2-2508-0102
Los Angeles
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
New York, NY
Tel: 631-435-6000
San Jose, CA
Tel: 408-735-9110
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
Canada - Toronto
Tel: 905-673-0699
Fax: 905-673-6509
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
03/25/14
DS20002281C-page 22
2011-2014 Microchip Technology Inc.
相关型号:
MTD6N08
Power Field-Effect Transistor, 6A I(D), 80V, 0.25ohm, 1-Element, N-Channel, Silicon, Metal-oxide Semiconductor FET, TO-252
MOTOROLA
©2020 ICPDF网 联系我们和版权申明