0639114100 [MOLEX]
T2 Terminator for Projector Lamp Plug and Receptacle Terminal, 18-20 AWG;
| 型号： | 0639114100 |
| 厂家： | 
Molex |
| 描述： | T2 Terminator for Projector Lamp Plug and Receptacle Terminal, 18-20 AWG |
| 文件： | 总6页 (文件大小：208K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
T2 Terminator for Sabre™ Flat Blade Crimp Terminal
T2 Terminator Tooling
Specification Sheet
Part No. 63911-3000
FEATURES
ꢀ
ꢀ
ꢀ
ꢀ
It is ideally suited for mid-volume bench operations
This terminator can be installed in the TM42 and the TM40 press or Base Unit adapter for 3BF press
Quick punch removal with the push of a button for fast and easy tooling change
Track adjustment capabilities in the T2 Terminators for improved control of the bell mouth size and cutoff tab
length
ꢀ
T2 Terminator has standardized tooling with the Molex FineAdjust Applicator which will reduce your inventory
requirements
SCOPE
Products: Sabre™ Flat Blade Crimp Terminal (2) 20 AWG, UL1015 wires.
Wire Size
AWG mm²
Insulation Diameter
mm In.
Strip Length
mm In.
Terminal Series No. Terminal Order No.
43374
43375
43374-5001
43375-5001
(2) 20 (2) 0.50 (2) 2.54 (2) 1.100 3.96-5.54 .156-.218
(2) 20 (2) 0.50 (2) 2.54 (2) 1.100 3.96-5.54 .156-.218
Note: Terminal will accommodate the UL1015 wires.
For UL1007 wires use Applicator 63901-2900.
DEFINITION OF TERMS
BEND UP
BELL MOUTH
BRUSH
SEAM
INSULATION
CRIMP
ROLLING
TWISTING
STRIP
LENGTH
BEND
DOWN
CONDUCTOR
CUT-OFF TAB
COND.CRIMP
HEIGHT
CRIMP
The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the scope.
Doc No: ATS-639113000
Revision: A
Release Date: 11-05-09
Revision Date: 11-09-09
UNCONTROLLED COPY
Page 1 of 6
T2 Terminator for Sabre™ Flat Blade Crimp Terminal
CRIMP SPECIFICATION
Cut-off Tab Conductor Brush
Maximum Maximum
mm In.
Bell mouth
mm In.
0.20-0.50 .008-.020 0.30 .012
Terminal Series No.
mm
0.76
In.
43374
43375
.030
Punch Width (Ref)
Conductor Insulation
Seam
Bend up Bend down Twist Roll
Terminal Series No.
Degree (Max)
Degree (Max) mm In mm In
2.50 .098 4.30 .169
Seam shall not be open
and no wire allowed out
of the crimping area
43374
43375
3
3
4
8
After crimping, the conductor profile should measure the following.
Conductor Crimp
Wire Size
Insulation Crimp Pull Force
Height (Ref) Minimum
Lb.
Terminal Series No.
Height
AWG mm2
mm
In.
mm
3.30
3.30
In.
N
43374
43375
(2) 20 (2) 0.50 1.23-1.31
(2) 20 (2) 0.50 1.23-1.31
.048-.051
.048-.051
.130 57.0 13.00
.130 57.0 13.00
Pull Force should be measured with no influence from the insulation crimp.
The above specifications are guidelines to an optimum crimp.
Doc No: ATS-639113000
Revision: A
Release Date: 11-05-09
Revision Date: 11-09-09
UNCONTROLLED COPY
Page 2 of 6
T2 Terminator for Sabre™ Flat Blade Crimp Terminal
PARTS LIST
T2 Terminator 63911-3000
Item Order No Engineering No. Description
Perishable Tooling
Quantity
63911-3070
63444-2513
63445-2562
63446-4313
63445-4317
63443-0035
63443-0036
63911-3070
63444-2513
63445-2562
63446-4313
63445-4317
63443-0035
63443-0036
Tool Kit (All “Y” Items)
Conductor Punch
Conductor Anvil
Insulation Punch
Insulation Anvil
Front Cut-Off Plunger
Front Plunger Retainer
REF
1 Y
1 Y
1 Y
1 Y
1 Y
1 Y
1
2
3
4
5
6
Other Components
7
8
9
11-18-4083
63443-0009
63443-0024
63443-0085
63443-0090
63443-1719
63443-2215
63443-2302
63443-2801
63443-2913
63443-6013
63443-7201
63600-1057
63600-2972
63700-0539
60707-8
Feed Guide
Scrap Chute
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
63443-0009
63443-0024
63443-0085
63443-0090
63443-1719
63443-2215
63443-2302
63443-2801
63443-2913
63443-6013
63443-7201
63600-1057
63600-2972
63700-0539
Key
10
11
12
13
14
15
16
17
18
19
20
21
Wire Stop L-Bracket
Wire Stop
18.90mm Spacer
15.00mm Spacer
3.10mm Spacer
Front Plunger Striker
Wire Hold Down Plunger
Rear Cover
Spring Cover
Striker Plunger Spring
Collar
Cut-Off Plunger Spring
Frame
22
63800-8500
63800-8500
T2 Terminator
1
Hardware
23
24
25
26
27
28
29
30
31
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
M3 by 6 Long SHCS
M3 by 6 Long FHCS
M4 by 6 Long SHCS
M4 by 12 Long BHCS
M4 by 14 Long SHCS
M4 by 30 Long SHCS
M4 by 50 Long SHCS
M5 by 12 Long SHCS
#10-32 by 3/8”Long BHCS
2**
1**
2**
2**
2**
2**
2**
1**
1**
** Available from an industrial supply company such as MSC (1-800-645-7270).
Doc No: ATS-639113000
Revision: A
Release Date: 11-05-09
Revision Date: 11-09-09
UNCONTROLLED COPY
Page 3 of 6
T2 Terminator for Sabre™ Flat Blade Crimp Terminal
Assembly Drawing
1
3
19
15
31
20
18
26
(2)
16
2
5
21
23
7
17
(2)
28
27
(2)
10
6
4
11
30
8
25
29
(2)
14
22
25
13
11
12
9
24
Figure 1
Doc No: ATS-639113000
Revision: A
Release Date: 11-05-09
Revision Date: 11-09-09
UNCONTROLLED COPY
Page 4 of 6
T2 Terminator for Sabre™ Flat Blade Crimp Terminal
NOTES
Depending on the press vintage a feed finger assembly is supplied with the T2 Terminator.
1. To remove the existing feed finger assembly loosens the M4 x 10 mm set screw in the feed lever.
2. Select T2 Feed finger assembly from Terminator box.
3. Insert a screwdriver into the slot behind the feed lever and force the feed arm spring to the right.
4. Slide the T2 feed finger shaft for TM42 (11-40-5307) or (11-40-0123) for TM40 /Base Unit into the feed lever
and to the left of the feed arm spring.
5. Release the feed arm spring.
6. Position feed finger for selected product. (Refer to Figure 5.1 in the T2 Manual).
TM40 PRESS AND
TM42 PRESS
BASE UNIT AND ADAPTER
11-40-0123
FEED FINGER ROD
11-40-5307
FEED FINGER ROD
COTTER PIN
COTTER PIN
1/8” X .0295 DIA. WIRE
1/8” X .0295 DIA. WIRE
11-40-5255
11-40-5255
FEED FINGER
FEED FINGER
11-40-0125
FEED ARM SPRING
11-40-0125
FEED ARM SPRING
FEED FINGER ASSEMBLY
FOR PRESS TM42
FEED FINGER ASSEMBLY
FOR PRESS TM40
Figure 2
Doc No: ATS-639113000
Revision: A
Release Date: 11-05-09
Revision Date: 11-09-09
UNCONTROLLED COPY
Page 5 of 6
T2 Terminator for Sabre™ Flat Blade Crimp Terminal
NOTES
1. Molex recommends an extra perishable tooling kit be maintained at your facility.
2. Verify tooling alignment by manually cycling the press before crimping under power. Check that all screws are
tight.
3. Slugs, Terminals, Dirt and Oil should be kept clear of work area.
4. This Terminator should be only used in a Molex TM42, TM40, or 3BF Press with a Base Unit adaptor.
5. Wear safety glasses at all times.
6. For recommended maintenance refer to the TM40, TM42 Manual.
CAUTION: To prevent injury never operate this Terminator without the guards supplied with the press or in
place. Reference the TM42 press manufacturer’s instruction manual.
CAUTION: Molex crimp specifications are valid only when used with Molex terminals, applicators and
tooling.
Americas Headquarters
Lisle, Illinois 60532 U.S.A. Yamato, Kanagawa, Japan
1-800-78MOLEX
amerinfo@molex.com
Far East North Headquarters Far East South Headquarters European Headquarters Corporate Headquarters
Jurong, Singapore
65-6-268-6868
Munich, Germany
49-89-413092-0
2222 Wellington Ct.
Lisle, IL 60532 U.S.A.
630-969-4550
81-462-65-2324
feninfo@molex.com
fesinfo@molex.com
eurinfo@molex.com
Fax: 630-969-1352
Visit our Web site at http://www.molex.com
Doc No: ATS-639113000
Revision: A
Release Date: 11-05-09
Revision Date: 11-09-09
UNCONTROLLED COPY
Page 6 of 6
相关型号：
©2020 ICPDF网 联系我们和版权申明