MC33207P [MOTOROLA]
LOW VOLTAGE RAIL-TO-RAIL OPERATIONAL AMPLIFIERS; 低电压轨到轨运算放大器型号: | MC33207P |
厂家: | MOTOROLA |
描述: | LOW VOLTAGE RAIL-TO-RAIL OPERATIONAL AMPLIFIERS |
文件: | 总13页 (文件大小:216K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Order this document by MC33206/D
LOW VOLTAGE
RAIL–TO–RAIL
OPERATIONAL AMPLIFIERS
SEMICONDUCTOR
TECHNICAL DATA
The MC33206/7 family of operational amplifiers provide rail–to–rail
operation on both the input and output. The inputs can be driven as high as
200 mV beyond the supply rails without phase reversal on the outputs and
the output can swing within 50 mV of each rail. This rail–to–rail operation
enables the user to make full use of the supply voltage range available. It is
designed to work at very low supply voltages (±0.9 V) yet can operate with a
single supply of up to 12 V and ground. Output current boosting techniques
provide a high output current capability while keeping the drain current of the
amplifier to a minimum.
MC33206
P SUFFIX
PLASTIC PACKAGE
CASE 646
14
1
The MC33206/7 has an enable mode that can be controlled externally.
D SUFFIX
PLASTIC PACKAGE
The typical supply current in the standby mode is <1.0 µA (V
= Gnd).
Enable
14
The addition of an enable function makes this amplifier an ideal choice for
power sensitive applications, battery powered equipment (instrumentation and
monitoring), portable telecommunication, and sample–and–hold applications.
CASE 751A
(SO–14)
1
N.C.
N.C.
1
2
3
4
5
6
7
14 N.C.
• Standby Mode (I ≤1.0 µA, Typ)
D
13
12
11
10
9
V
CC
Output 2
• Low Voltage, Single Supply Operation
Output 1
(1.8 V and Ground to 12 V and Ground)
1
2
Inputs 1
Inputs 2
• Rail–to–Rail Input Common Mode Voltage Range
• Output Voltage Swings within 50 mV of both Rails
• No Phase Reversal on the Output for Over–Driven Input Signals
Enable 1
Enable 2
N.C.
8
V
EE
(Dual, Top View)
• High Output Current (I
SC
= 80 mA, Typ)
MC33207
• Low Supply Current (I = 0.9 mA, Typ)
D
• 600 Ω Output Drive Capability
P SUFFIX
PLASTIC PACKAGE
CASE 648
• Typical Gain Bandwidth Product = 2.2 MHz
16
1
D SUFFIX
PLASTIC PACKAGE
CASE 751B
16
ORDERING INFORMATION
Operational
Operating
1
(SO–16)
Amplifier Function
Temperature Range
Device
MC33206D
MC33206P
MC33207D
MC33207P
Package
SO–14
Output 1
Inputs 1
1
16 Enable 1, 4
15 Output 4
14
Dual
2
3
4
5
6
7
8
Plastic DIP
SO–16
1
2
T = –40 ° to +105°C
A
4
3
Inputs 4
13
12
11
10
9
V
CC
Quad
Plastic DIP
V
EE
Inputs 2
Inputs 3
Output 2
Enable 2, 3
Output 3
(Quad, Top View)
This document contains information on a new product. Specifications and information herein
Motorola, Inc. 1996
Rev 0
are subjecttochangewithout notice.
MC33206 MC33207
MAXIMUM RATINGS
Rating
to V
Symbol
Value
13
Unit
V
Supply Voltage (V
)
V
S
CC
EE
ESD Protection Voltage at any Pin
Human Body Model
V
ESD
2,000
V
Voltage at any Device Pin
V
V
± 0.5
V
V
V
DP
S
Input Differential Voltage Range
Common Mode Input Voltage Range (Note 2)
V
IDR
(Note 1)
V
CM
V
+ 0.5 to
– 0.5
CC
V
EE
Output Short Circuit Duration (Note 3)
Maximum Junction Temperature
Storage Temperature Range
t
(Note 3)
+150
sec
°C
s
T
J
T
stg
–65 to +150
(Note 3)
°C
Maximum Power Dissipation
P
mW
D
NOTES: 1. The differential input voltage of each amplifier is limited by two internal parallel back–to–back
diodes. For additional differential input voltage range, use current limiting resistors in series
with the input pins.
2. The common–mode input voltage range of each amplifier is limited by diodes connected from
the inputs to both power supply rails. Therefore, the voltage on either input must not exceed
either supply rail by more than 500 mV.
3. Power dissipation must be considered to ensure maximum junction temperature (T ) is not
J
exceeded.
4. ESD data available upon request.
DC ELECTRICAL CHARACTERISTICS (V
= 5.0 V, V
= 0 V, V
= 5.0 V, T = 25°C, unless otherwise noted.)
Enable A
CC
EE
Characteristic
Figure
Symbol
Min
Typ
Max
Unit
Input Offset Voltage (V
0 to 0.5 V, V
1.0 to 5.0 V)
–
V
IO
mV
CM
MC33206: T = 25°C
CM
–
–
–
–
0.5
1.0
0.5
1.0
8.0
11
10
13
A
MC33201: T = –40° to +105°C
A
MC33207: T = 25°C
A
MC33202: T = –40° to +105°C
A
Input Offset Voltage Temperature Coefficient (R = 50 Ω)
–
–
∆V /∆T
IO
–
2.0
–
µV/°C
S
T
A
= –40° to +105°C
Input Bias Current (V
= 0 to 0.5 V, V
= 1.0 to 5.0 V)
I
IB
nA
CM
CM
T
T
= 25°C
–
–
80
100
200
250
A
= –40° to +105°C
A
Input Offset Current (V
= 0 to 0.5 V, V
= 1.0 to 5.0 V)
–
I
IO
nA
CM
CM
T
T
= 25°C
–
–
5.0
10
50
100
A
= –40° to +105°C
A
Common Mode Input Voltage Range
–
–
V
–
V
V
+ 0.2
– 0.2
V
V
ICR
CC
EE
CC
–
V
EE
Large Signal Voltage Gain (V
= 5.0 V, V
= –5.0 V)
A
VOL
kV/V
CC
EE
R
R
= 10 kΩ
= 600 Ω
50
25
300
250
–
–
L
L
Output Voltage Swing (V = ±0.2 V)
ID
–
V
R
L
R
L
R
L
R
L
= 10 kΩ
= 10 kΩ
= 600 Ω
= 600 Ω
V
V
4.85
–
4.75
–
4.95
0.05
4.85
0.15
–
0.15
–
OH
OL
V
V
OH
0.25
OL
Common Mode Rejection (V = 0 to 5.0 V)
in
–
–
CMR
60
90
–
dB
Power Supply Rejection Ratio
PSRR
PSR
–
66
25
92
500
–
µV/V
dB
V /V
CC EE
= 5.0 V/Gnd to 3.0 V/Gnd
Output Short Circuit Current (Source and Sink)
–
I
50
80
–
mA
SC
2
MOTOROLA ANALOG IC DEVICE DATA
MC33206 MC33207
DC ELECTRICAL CHARACTERISTICS (continued) (V
= 5.0 V, V
= 0 V, V
= 5.0 V, T = 25°C, unless otherwise noted.)
A
CC
EE
Enable
Symbol
Characteristic
Figure
Min
Typ
Max
Unit
Power Supply Current (V = 2.5 V, T = –40° to +105°C,
–
I
D
O
A
per Amplifier)
MC33206: V
MC33206: V
MC33207: V
MC33207: V
= 5.0 Vdc
= Gnd (Standby)
= 5.0 Vdc
–
–
–
–
0.8
0.5
1.5
0.5
1.125
6.0
2.25
6.0
mA
µA
mA
µA
Enable
Enable
Enable
Enable
= Gnd (Standby)
Enable Input Voltage (per Amplifier)
Enabled – Amplifier “On”
Disabled – Amplifier “Off” (Standby)
–
–
V
V
Enable
–
–
V
EE
V
EE
+ 1.8
+ 0.3
–
–
Enable Input Current (Note 5) (per Amplifier)
I
µA
Enable
V
V
V
V
= 12 V
= 5.0 V
= 1.8 V
= Gnd
–
–
–
–
2.5
–
–
–
–
Enable
Enable
Enable
Enable
2.2
0.8
0
NOTE: 5. External control circuitry must provide for an initial turn–off transient of <10 µA.
AC ELECTRICAL CHARACTERISTICS (V
= 5.0 V, V
= 0 V, V
= 5.0 V, T = 25°C, unless otherwise noted.)
A
CC
EE
Enable
Characteristic
Figure
Symbol
Min
Typ
Max
Unit
Slew Rate (V = ±2.5 V, V = –2.0 to +2.0 V,
–
SR
0.5
1.0
–
V/µs
S
O
R
= 2.0 kΩ, A = 1.0)
V
L
Gain Bandwidth Product (f = 100 kHz)
Phase Margin (R = 600 Ω, C = 0 pF)
–
–
–
–
–
GBW
M
–
–
–
–
–
2.2
65
12
90
28
–
–
–
–
–
MHz
Deg
dB
L
L
Gain Margin (R = 600 Ω, C = 0 pF)
A
M
L
L
Channel Separation (f = 1.0 Hz to 20 kHz, A = 100)
CS
BW
dB
V
Power Bandwidth (V = 4.0 Vpp, R = 600 Ω, THD ≤ 1%)
kHz
%
O
L
P
Total Harmonic Distortion (R = 600 Ω, V = 1.0 Vpp, A = 1.0)
THD
L
O
V
–
f = 1.0 kHz
f = 10 kHz
–
–
0.002
0.008
–
–
Open Loop Output Impedance
(V = 0 V, f = 2.0 MHz, A = 10)
–
Z
O
–
100
–
Ω
O
V
Differential Input Resistance (V
CM
= 0 V)
= 0 V)
–
–
–
R
in
C
in
e
n
–
–
200
8.0
–
–
kΩ
Differential Input Capacitance (V
pF
CM
Equivalent Input Noise Voltage (R = 100 Ω)
nV/
Hz
S
f = 10 Hz
–
–
25
20
–
–
f = 1.0 kHz
Equivalent Input Noise Current
f = 10 Hz
–
i
n
pA/
Hz
–
–
0.8
0.2
–
–
f = 1.0 kHz
Time Delay for Device to Turn On
Time Delay for Device to Turn Off
–
–
t
t
–
–
10
–
–
µs
µs
on
2.0
off
3
MOTOROLA ANALOG IC DEVICE DATA
MC33206 MC33207
Figure 1. Circuit Schematic
(Each Amplifier)
V
CC
V
CC
V
CC
V
CC
V
–
+
in
Enable
V
in
V
EE
This device contains 96 active transistors (each amplifier).
Figure 2. Maximum Power Dissipation
versus Temperature
Figure 3. Input Offset Voltage Distribution
4000
3500
3000
2500
2000
1500
1000
500
40
35
30
25
20
360 amplifiers tested
from 3 wafer lots
16 Pin DIP
14 Pin DIP
V
V
= 5.0 V
= Gnd
CC
EE
T
= 25
°C
A
DIP Package
15
10
5.0
0
SO–14/SO–1
6
0
–60
–30
0
30
60
90
C)
120
150
–10 –8.0 –6.0 –4.0 –2.0
0
2.0
4.0
6.0
8.0
10
T , AMBIENT TEMPERATURE (
°
V
IO
, INPUT OFFSET VOLTAGE (mV)
A
4
MOTOROLA ANALOG IC DEVICE DATA
MC33206 MC33207
Figure 4. Input Offset Voltage
Temperature Coefficient Distribution
Figure 5. Input Bias Current
versus Temperature
50
40
200
160
120
80
V
V
= 5.0 V
= Gnd
360 amplifiers tested
from 3 wafer lots
CC
EE
V
V
= 5.0 V
= Gnd
CC
EE
T
= 25
°C
A
30
20
DIP Package
V
= 0 V to 0.5 V
CM
V
> 1.0 V
CM
10
0
40
0
–55 –40 –25
0
25
70
85
125
–50 –40 –30 –20
–10
0
10
20
30
40
50
TC , INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT (
µV/°C)
V
T , AMBIENT TEMPERATURE (°C)
IO
A
Figure 6. Input Bias Current
versus Common Mode Voltage
Figure 7. Open Loop Voltage Gain
versus Temperature
150
100
50
300
260
0
220
–50
–100
–150
–200
–250
180
140
100
V
V
R
= 5.0 V
= Gnd
CC
EE
V
= 12 V
= Gnd
= 25°C
CC
V
T
= 600
Ω
EE
A
L
∆
V
= 0.5 V to 4.5 V
O
0
2.0
V
4.0
6.0
8.0
10
12
–55 –40 –25
0
25
70
85
105 125
, INPUT COMMON MODE VOLTAGE (V)
T , AMBIENT TEMPERATURE (
°C)
CM
A
Figure 8. Output Voltage Swing
versus Supply Voltage
Figure 9. Output Saturation Voltage
versus Load Current
V
V
12
10
CC
R
= 600 Ω
T
= –55°C
L
A
T
= 25
°C
A
T
= 125°C
A
–
CC
T
= 25°C
A
8.0
6.0
4.0
2.0
V
V
–
+
CC
EE
V
V
= 5.0 V
= –5.0 V
CC
EE
T
= 25°C
A
V
+
EE
T
= 125°C
A
T
= –55°C
A
0
V
EE
±1.0
±2.0
±
3.0
±
4.0
±5.0
±6.0
0
5.0
10
I , LOAD CURRENT (mA)
15
20
V
, V
EE
SUPPLY VOLTAGE (V)
CC
L
5
MOTOROLA ANALOG IC DEVICE DATA
MC33206 MC33207
Figure 10. Output Voltage
versus Frequency
Figure 11. Common Mode Rejection
versus Frequency
12
9.0
6.0
100
80
60
40
V
V
V
= 6.0 V
= –6.0 V
= 600 Ω
= 1.0
CC
EE
L
= 6.0 V
= –6.0 V
= –55° to +125°C
CC
R
A
3.0
0
V
T
EE
A
20
V
A
T
= 25°C
0
10
1.0 k
10 k
100 k
1.0 M
1.0 M
125
100
1.0 k
10 k
100 k
1.0 M
f, FREQUENCY (Hz)
f, FREQUENCY (Hz)
Figure 12. Power Supply Rejection
versus Frequency
Figure 13. Output Short Circuit Current
versus Output Voltage
120
100
80
100
80
60
40
20
0
Source
PSR+
PSR–
Sink
60
40
20
0
V
V
T
= 6.0 V
= –6.0 V
= 25
V
V
T
= 6.0 V
CC
EE
A
CC
EE
A
= –6.0 V
to +125°C
°C
= –55
°
10
0
1.0
2.0
3.0
4.0
5.0
6.0
100
1.0 k
10 k
100 k
f, FREQUENCY (Hz)
V
, OUTPUT VOLTAGE (V)
out
Figure 14. Output Short Circuit Current
versus Temperature
Figure 15. Supply Current per Amplifier
versus Supply Voltage with No Load
2.0
1.6
1.2
0.8
0.4
0
150
125
V
V
= 5.0 V
= Gnd
CC
EE
T
= 125°C
100
A
Source
Sink
T
= 25°C
75
50
25
A
T
= –55
°C
A
0
–55 –40 –25
0
25
70
85
105
±
0
±
1.0
±
2.0
±
3.0
±
4.0
±5.0
± .0
T , AMBIENT TEMPERATURE (
°C)
V
,
V
, SUPPLY VOLTAGE (V)
A
CC
EE
6
MOTOROLA ANALOG IC DEVICE DATA
MC33206 MC33207
Figure 16. Slew Rate
versus Temperature
Figure 17. Gain Bandwidth Product
versus Temperature
2.0
4.0
V
V
V
= 2.5 V
= –2.5 V
V
V
= 2.5 V
= –2.5 V
CC
EE
O
CC
EE
=
±2.0 V
f = 100 kHz
3.0
2.0
1.0
0
1.5
1.0
0.5
0
+Slew Rate
–Slew Rate
–55 –40 –25
0
25
70
85
105
125
–55 –40 –25
0
25
70 85
C)
105
125
T , AMBIENT TEMPERATURE (
°
C)
T , AMBIENT TEMPERATURE (°
A
A
Figure 18. Voltage Gain and Phase
versus Frequency
Figure 19. Voltage Gain and Phase
versus Frequency
70
50
40
70
50
40
V
=
= 25
= 600
±
6.0 V
C = 0 pF
L
S
T
°
C
Ω
T = 25°C
A
A
R
R = 600 Ω
L
80
80
L
30
10
120
160
200
240
30
10
120
160
1A
1A
2A
2A
2B
1B
1A – Phase, C = 0 pF
L
1A – Phase, V
=
±
6.0 V
S
=
2B
1B – Gain, C = 0 pF
L
1B
1B – Gain, V
2A – Phase, V
±6.0 V
=
±
–10
–30
S
–10
200
240
2A – Phase, C = 300 pF
L
±1.0 V
S
=
2B – Gain, C = 300 pF
L
2B – Gain, V
1.0 V
S
–30
10 k
10 k
100 k
1.0 M
10 M
100 k
f, FREQUENCY (Hz)
1.0 M
10 M
f, FREQUENCY (Hz)
Figure 20. Gain and Phase Margin
versus Temperature
Figure 21. Gain and Phase Margin
versus Differential Source Resistance
70
60
50
40
30
20
10
0
70
60
50
40
30
20
10
0
75
60
75
60
Phase Margin
Phase Margin
V
V
= 6.0 V
= –6.0 V
CC
EE
45
30
45
30
15
V
V
R
C
= 6.0 V
= –6.0 V
CC
EE
L
L
T
= 25
°C
A
= 600
Ω
= 100 pF
15
0
Gain Margin
Gain Margin
70 85
T , AMBIENT TEMPERATURE ( C)
0
–55 –40 –25
0
25
105
125
10
100
1.0 k
10 k
100 k
°
R , DIFFERENTIAL SOURCE RESISTANCE (Ω)
A
T
7
MOTOROLA ANALOG IC DEVICE DATA
MC33206 MC33207
Figure 23. Output Voltage
versus Load Resistance
Figure 22. Gain and Phase Margin
versus Capacitive Load
5.0
4.0
3.0
2.0
1.0
0
80
70
60
50
40
30
20
16
14
12
10
8.0
6.0
4.0
2.0
0
V
V
R
= 6.0 V
= –6.0 V
= 600 Ω
= 100
CC
EE
L
V
= 5.0 Vdc
CC
Phase Margin
Gain Margin
A
V
A
T
= 25°C
V
= 2.0 Vdc
V
= Gnd
= 0 pF
= 1.0
CC
EE
L
C
A
10
0
V
A
T
= 25°C
10
100
1.0 k
10 k
100 k
10
100
C , CAPACITIVE LOAD (pF)
1.0 k
R , LOAD RESISTANCE
L
L
Figure 24. Channel Separation
versus Frequency
Figure 25. Total Harmonic Distortion
versus Frequency
10
150
120
V
= 5.0 V
V
R
= –5.0 V
CC
EE
= 600
T
= 25
°C
Ω
A
L
A
= 100
V
V
= 2.0 Vpp
O
1.0
A
= 1000
= 100
V
90
60
30
0
A
V
0.1
0.01
A
= 10
V
A
= 10
V
V
V
V
T
= 6.0 V
= –6.0 V
= 8.0 Vpp
= 25°C
CC
EE
O
A
= 1.0
A
V
0.001
100
1.0 k
10 k
10
100
1.0 k
10 k
100 k
f, FREQUENCY (Hz)
f, FREQUENCY (Hz)
Figure 26. Equivalent Input Noise Voltage
and Current versus Frequency
50
40
5.0
4.0
V
V
= 6.0 V
= –6.0 V
CC
EE
T
= 25
°C
A
30
20
10
3.0
2.0
1.0
Noise Voltage
Noise Current
0
10
0
100
1.0 k
f, FREQUENCY (Hz)
10 k
100 k
8
MOTOROLA ANALOG IC DEVICE DATA
MC33206 MC33207
Figure 28. t Response
on
GENERAL INFORMATION
The MC33206/7 family of operational amplifiers are
unique in their ability to swing rail–to–rail on both the input
and the output with a completely bipolar design. This offers
low noise, high output current capability and a wide common
mode input voltage range even with low supply voltages.
Operation is guaranteed over an extended temperature
range and at supply voltages of 2.0 V, 3.3 V and 5.0 V and
ground.
Since the common mode input voltage range extends from
V
to V , it can be operated with either single or split
CC
EE
voltage supplies. The MC33206/7 are guaranteed not to latch
or phase reverse over the entire common mode range,
however, the inputs should not be allowed to exceed
maximum ratings.
t
, TIME (2.0 µs/DIV)
on
CIRCUIT INFORMATION
Figure 29. t
off
Response
Rail–to–rail performance is achieved at the input of the
amplifiers by using parallel NPN–PNP differential input
stages. When the inputs are within 800 mV of the negative
rail, the PNP stage is on. When the inputs are more than
800 mV greater than V , the NPN stage is on. This
EE
switching of input pairs will cause a reversal of input bias
currents (see Figure 6). Also, slight differences in offset
voltage may be noted between the NPN and PNP pairs.
Cross–coupling techniques have been used to keep this
change to a minimum.
In addition to its rail–to–rail performance, the output stage
is current boosted to provide 80 mA of output current,
enabling the op amp to drive 600 Ω loads. Because of this
high output current capability, care should be taken not to
exceed the 150°C maximum junction temperature.
t
, TIME (2.0 µs/DIV)
off
Low Voltage Operation
Enable Function
The MC33206/07 will operate at supply voltages down to
1.8 V and ground. Since this device is a rail–to–rail on both
the input and output, one can be assured of continued
operation in battery applications when battery voltages drop
to low voltage levels. This is called End of Discharge (see
Figure 30). Now, the user can select a minimum quantity of
batteries best suited for the particular design depending on
the type of battery chosen. This will minimize part count in
many designs.
The MC33206/07 enable pins allow the user to externally
control the device. (Refer to the Pin Diagram on the first page
of this data sheet for enable pin connections.) If the enable
pins are pulled low (Gnd) each amplifier (MC33206) and
amplifier pair (MC33207) will be disabled. When the enable
pins are at a logic high (V
will turn “on”. Refer to the data sheet characteristics for the
required levels needed to change logical state.
≥ V
= 1.8 V) the amplifiers
Enable
EE
The time to change states (from device “on” to “off” and
“off” to “on”) is defined as the time delay. The Circuit in
Figure 30. Typical Battery Characteristics
Figure27isusedtomeasuret andt . Typicalt andt
on off on
off
Type
Operating Voltage
End of Discharge
measurements are shown in Figures 28 and 29. When the
device is turned off (V = Gnd) an internal regulator is
Alkaline
NiCd
NiMh
Silver Oxide
Lithium Ion
1.5 V
1.2 V
1.2 V
1.6 V
3.6 V
0.9 V
1.0 V
1.0 V
1.3 V
2.5 V
Enable
shut off disabling the amplifier.
Figure 27. Test Circuit for t and t
on
off
V
CC
Compensating for Output Capacitance
The combination of device output impedance and
increasing capacitive loading will cause phase delay
(reducing the phase margin) in any amplifier (Figure 22). If
the loading is excessive, the resulting response can be circuit
oscillation. In other words, an amplifier can become unstable
when the phase becomes greater than 180 degrees before
the open loop gain drops to unity gain. Figures 18 and 19
show this situation as frequency increases for a given load.
The MC33206/7 can typically drive up to 300 pF loads at
unity gain without oscillating.
V
MC33206
out
t
t
off
on
2.0 V
2.0 k
V
Enable
t
t
off
on
9
MOTOROLA ANALOG IC DEVICE DATA
MC33206 MC33207
Figure 31. Capacitive Loads Compensation
R
f
C
X
R
O
C
L
R
L
V
in
There are several ways to compensate for this
phenomena. Adding series resistance to the output is one
way, but not an ideal solution. A dc voltage error will occur at
the output. A better design solution to compensate for higher
capacitive loads would be to use the circuit in Figure 31. This
design helps to counteract the loss of phase margin by taking
the high frequency output signal and feeding it back into the
amplifier inverting input. This technique helps to overcome
oscillation due to a highly capacitive load. Keep in mind that
compensation will have the affect of lowering the Gain
SPICE Model
If a SPICE Macromodel is desired for the MC33206/07,
the user can define the characteristics from the following
information. Obtain the SPICE Macromodel for the MC33204
Rail–to–Rail Operational Amplifier (device is the same as the
MC33207). For the Enable feature of the MC33207, simulate
it as a bipolar switch. The Macromodel does not include an
input capacitance between the inverting and noninverting
inputs. This capacitor is called C . Add 3.0 to 5.0 pF if
stability analysis is required.
in
Bandwidth Product (GPW). The values of C and R0, are
X
determined experimentally. Typical C and C will be the
X
L
same value.
Figure 32. Noninverting Amplifier Slew Rate
Figure 33. Small Signal Transient Response
V
V
R
C
= 6.0 V
= –6.0 V
V
V
R
C
= 6.0 V
= –6.0 V
CC
EE
L
L
CC
EE
L
L
= 600
Ω
= 600
Ω
= 100 pF
= 100 pF
T
= 25
°C
T
= 25
°C
A
A
t, TIME (5.0
µs/DIV)
t, TIME (10 µs/DIV)
Figure 34. Large Signal Transient Response
V
V
R
C
= 6.0 V
= –6.0 V
CC
EE
L
L
= 600
Ω
= 100 pF
= 1.0
A
V
A
T
= 25°C
t, TIME (10 µs/DIV)
10
MOTOROLA ANALOG IC DEVICE DATA
MC33206 MC33207
OUTLINE DIMENSIONS
P SUFFIX
PLASTIC PACKAGE
CASE 646–06
ISSUE L
NOTES:
1. LEADS WITHIN 0.13 (0.005) RADIUS OF TRUE
POSITION AT SEATING PLANE AT MAXIMUM
MATERIAL CONDITION.
2. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
3. DIMENSION B DOES NOT INCLUDE MOLD
FLASH.
4. ROUNDED CORNERS OPTIONAL.
14
1
8
7
B
INCHES
MILLIMETERS
A
F
DIM
A
B
C
D
F
G
H
J
K
L
M
N
MIN
MAX
0.770
0.260
0.185
0.021
0.070
MIN
18.16
6.10
3.69
0.38
1.02
MAX
19.56
6.60
4.69
0.53
1.78
0.715
0.240
0.145
0.015
0.040
L
C
0.100 BSC
2.54 BSC
0.052
0.008
0.115
0.095
0.015
0.135
1.32
0.20
2.92
2.41
0.38
3.43
J
N
0.300 BSC
7.62 BSC
SEATING
PLANE
K
0
10
0
10
0.015
0.039
0.39
1.01
H
G
D
M
D SUFFIX
PLASTIC PACKAGE
CASE 751A–03
(SO–14)
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
ISSUE F
–A–
14
1
8
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
–B–
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
P 7 PL
M
M
0.25 (0.010)
B
7
MILLIMETERS
INCHES
G
DIM
A
B
C
D
F
G
J
K
M
P
MIN
8.55
3.80
1.35
0.35
0.40
MAX
8.75
4.00
1.75
0.49
1.25
MIN
MAX
0.344
0.157
0.068
0.019
0.049
F
R X 45
C
0.337
0.150
0.054
0.014
0.016
–T–
SEATING
PLANE
J
M
1.27 BSC
0.050 BSC
K
D 14 PL
0.19
0.10
0
0.25
0.25
7
0.008
0.004
0
0.009
0.009
7
M
S
S
0.25 (0.010)
T
B
A
5.80
0.25
6.20
0.50
0.228
0.010
0.244
0.019
R
P SUFFIX
PLASTIC PACKAGE
CASE 648–08
ISSUE R
NOTES:
–A–
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
16
9
B
S
1
8
INCHES
MILLIMETERS
DIM
A
B
C
D
F
MIN
MAX
0.770
0.270
0.175
0.021
0.70
MIN
18.80
6.35
3.69
0.39
1.02
MAX
19.55
6.85
4.44
0.53
1.77
F
0.740
0.250
0.145
0.015
0.040
C
L
SEATING
PLANE
–T–
G
H
J
K
L
0.100 BSC
0.050 BSC
2.54 BSC
1.27 BSC
K
M
0.008
0.015
0.130
0.305
10
0.21
0.38
3.30
7.74
10
H
J
0.110
0.295
0
2.80
7.50
0
G
D 16 PL
M
S
0.020
0.040
0.51
1.01
M
M
0.25 (0.010)
T A
11
MOTOROLA ANALOG IC DEVICE DATA
MC33206 MC33207
OUTLINE DIMENSIONS
D SUFFIX
PLASTIC PACKAGE
CASE 751B–05
(SO–16)
ISSUE J
–A–
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
16
1
9
8
–B–
P 8 PL
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
M
S
0.25 (0.010)
B
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
G
MILLIMETERS
INCHES
DIM
A
B
C
D
MIN
9.80
3.80
1.35
0.35
0.40
MAX
10.00
4.00
1.75
0.49
1.25
MIN
MAX
0.393
0.157
0.068
0.019
0.049
F
0.386
0.150
0.054
0.014
0.016
R X 45
K
C
F
G
J
K
M
P
R
1.27 BSC
0.050 BSC
–T–
SEATING
PLANE
0.19
0.10
0
0.25
0.25
7
0.008
0.004
0
0.009
0.009
7
J
M
D
16 PL
5.80
0.25
6.20
0.50
0.229
0.010
0.244
0.019
M
S
S
0.25 (0.010)
T
B
A
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specificallydisclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
datasheetsand/orspecificationscananddovaryindifferentapplicationsandactualperformancemayvaryovertime. Alloperatingparameters,including“Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applicationsintended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
ordeathmayoccur. ShouldBuyerpurchaseoruseMotorolaproductsforanysuchunintendedorunauthorizedapplication,BuyershallindemnifyandholdMotorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola nd are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454
3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315
MFAX: RMFAX0@email.sps.mot.com – TOUCHTONE 602–244–6609
INTERNET: http://Design–NET.com
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
MC33206/D
◊
WWW.ALLDATASHEET.COM
Copyright © Each Manufacturing Company.
All Datasheets cannot be modified without permission.
This datasheet has been download from :
www.AllDataSheet.com
100% Free DataSheet Search Site.
Free Download.
No Register.
Fast Search System.
www.AllDataSheet.com
相关型号:
©2020 ICPDF网 联系我们和版权申明