R5-PC2 [MSYSTEM]
Remote I/O R5 Series;
| 型号： | R5-PC2 |
| 厂家： | 
M-SYSTEM |
| 描述： | Remote I/O R5 Series |
| 文件： | 总3页 (文件大小：116K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MODEL: R5-PC2
RUN indicator: Bi-color (red/green) LED;
Remote I/O R5 Series
Red when the bus A operates normally;
Green when the bus B operates normally;
Amber when both buses operate normally.
Output status indicator: Red LED; turns on with the outputs
ON.
PULSE OUTPUT MODULE
(photo MOSFET relay output, 2 points)
18 (.71)
Pulse width adjustment: 5 msec., 10 msec., 50 msec., 100
msec., 500 msec., 1 sec., 1.5 sec., 2 sec. (Side DIP SW)
Count reset: Via DIP switches on the side
90
(3.54)
OUTPUT SPECIFICATIONS
Output: Photo MOSFET relay contact, 2 points
96.5
(3.80)
Common: Each point independent
mm (inch)
Rated load: 125 V AC/DC @ 50 mA (resistive load)
Maximum ON resistance: 50 Ω
Maximum frequency: 100 Hz (DIP SW selectable)
Totalized pulse range: 1 – 10000 (‘0’ at reset)
(Max. pulse range selectable from 100 to 60000 using the
R5CON PC Configurator Software. Refer to the R5CON Users
Manual for detailed information.)
MODEL: R5–PC2[1][2]
ORDERING INFORMATION
• Code number: R5-PC2[1][2]
Specify a code from below for each of [1] and [2].
(e.g. R5-PC2W/Q)
Count at overflow: Reset and restart at ‘1.’
• Specify the specification for option code /Q
(e.g. /C01)
INSTALLATION
Operating temperature: -10 to +55°C (14 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Atmosphere: No corrosive gas or heavy dust
Mounting: Installation Base (model: R5-BS)
Weight: 100 g (0.22 lb)
NO. OF CHANNELS
2: 2-point outputs
[1] COMMUNICATION MODE
S: Single
PERFORMANCE
Data allocation: 2
W: Dual
Response time: ≤ 0.1 sec.
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 1500 V AC @ 1 minute
(Po 1 to Po 2 to internal bus or internal power)
2000 V AC @ 1 minute (power input to FG;
isolated on the power supply module)
[2] OPTIONS
blank: none
/Q: With options (specify the specification)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating
GENERAL SPECIFICATIONS
Connection
Internal bus: Via the Installation Base (model: R5-BS)
Output: Euro type connector terminal
(Applicable wire size: 0.2 – 2.5 mm
2
(AWG24 - 12),
stripped length 7 mm)
Internal power: Via the base (model: R5-BS)
Isolation: Po 1 to Po 2 to internal bus or internal power
R5-PC2 SPECIFICATIONS
ES-6140 Rev.11 Page 1/3
https://www.m-system.co.jp/
MODEL: R5-PC2
STANDARDS & APPROVALS
EU conformity:
EMC Directive
EMI EN 61000-6-4
EMS EN 61000-6-2
Low Voltage Directive
EN 61010-1, EN 61010-2-201
Measurement Category II (output)
Pollution Degree 2
Output to internal bus or internal power – Basic insulation
(300 V)
RoHS Directive
FUNCTIONS
■ Counter reset
1) Remove Network Module or its cables and interrupt
communication with other devices.
2) Turn ON the Counter Reset SW (SW8) on the module.
3) Return the module to the base and turn the power supply
on.
4) Red RUN LED turns on and the module starts resetting its
counter. When the resetting is complete, the LED light turns
to green. DO NOT remove the power while the red light is
on.
5) After the green LED is confirmed, turn the power supply
off.
6) Turn OFF the Counter Reset SW (SW8).
7) Return the Network module onto the base and turn the
power supply on.
Note: Counter Reset SW must be turned OFF after this
procedure because the module does not start counting with
ON state.
EXTERNAL VIEW
■ SIDE VIEW
■ FRONT VIEW
RUN LED
RUN
1
2
3
4
Status Indicator LED
1 2 3 4 5 6 7 8
ON
OFF
Counter
Reset
Pulse Width
4
1
5
2
6
3
Unused
Euro Type
Connector Terminals
Note: Counter Reset SW is normally OFF during operation.
R5-PC2 SPECIFICATIONS
ES-6140 Rev.11 Page 2/3
https://www.m-system.co.jp/
MODEL: R5-PC2
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm [inch]
LOCKING CLAMP
18 (.71)
6.5
90 (3.54)
(.26)
4
1
5
2
6
3
POSITIONING GUIDE
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
RUN OUTPUT STATUS
LED INDICATOR LED
•
• • • •
Isolation
INTERNAL BUS A
1
3
Communication
Circuit
1
3
4
6
2
5
Po 1
*INTERNAL BUS B
Control
Circuit
COM1
Po 2
Isolation
INTERNAL POWER
COM2
DIP SW
*For dual redundant communication.
Note: Italic typed numbers correspond to the LEDs on the front panel.
Specifications are subject to change without notice.
R5-PC2 SPECIFICATIONS
ES-6140 Rev.11 Page 3/3
https://www.m-system.co.jp/
相关型号：
©2020 ICPDF网 联系我们和版权申明