R7F4HEIP-DAC16B [MSYSTEM]
Remote I/O R7F4HEIP Series EtherNet/IP I/O MODULE;
| 型号： | R7F4HEIP-DAC16B |
| 厂家： | 
M-SYSTEM |
| 描述： | Remote I/O R7F4HEIP Series EtherNet/IP I/O MODULE |
| 文件： | 总5页 (文件大小：524K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MODEL: R7F4HEIP-DAC16B
Remote I/O R7F4HEIP Series
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
EtherNet/IP I/O MODULE
(NPN discrete input, PNP transistor output, 8 points each,
/C02: Polyurethane coating
/C03: Rubber coating
tension clamp terminal block)
Functions & Features
• 8 points NPN discrete input, 8 points PNP transistor output
module for EtherNet/IP
RELATED PRODUCTS
• PC configurator software (model: R7CFG)
• Supports DLR (Device Level Ring) to form a ring topology
• EDS file
The EDS file and configurator software are downloadable at
M-System’s web site.
A dedicated cable is required to connect the module to the
PC. Please refer to the internet software download site or
the users manual for the PC configurator for applicable
cable types.
115 [4.53]
55 [2.17]
GENERAL SPECIFICATIONS
Connection
72 [2.83]
mm [inch]
EtherNet/IP: RJ-45 Modular Jack
Power supply, exc. supply, I/O: Tension clamp terminal
Housing material: Flame-resistant resin (gray)
Isolation: Input or exc. supply to output or exc. supply to
EtherNet/IP or FE to power
MODEL: R7F4HEIP-DAC16B-4-R[1]
Output at the loss of communication: Configurable via
R7CFG
ORDERING INFORMATION
• Code number: R7F4HEIP-DAC16B-4-R[1]
Specify a code from below for [1].
(e.g. R7F4HEIP-DAC16B-4-R/Q)
• Specify the specification for option code /Q
(e.g. /C01)
Status indicator LED: PWR, LNK1, LNK2
(Refer to the instruction manual)
Discrete I/O status indicator LED: Green LED turns on with
I/O ON
Read rate: Selectable with R7CFG
I/O TYPE
DAC16B: NPN discrete input &
EtherNet/IP COMMUNICATION
Communication Standard: IEEE 802.3u
Transmission: 10BASE-T, 100BASE-TX
Baud rate: 10/100 Mbps (Auto Negotiation function)
Protocol: EtherNet/IP
PNP transistor output, 8 points each
TERMINAL BLOCK: 4
Max. number of socket connections: 3
Connection type: Exclusive owner / Listen only / Input only
Transmission media: 10BASE-T (STP, Category 5), 100BASE-
TX (STP, Category 5e)
Tension clamp terminal block for power supply
RJ-45 Modular jack for communication
Tension clamp terminal block for I/O
Network topology: Line, star and ring
Max. length of fieldbus segment: 100 meters
IP address: 192.168.0.250 (factory setting);
Only host address in IP address is configurable via rotary
switches, the other items via PC configurator software
(model: R7CFG).
POWER INPUT
DC power
R: 24 V DC
(Operational voltage range: ±10 %; ripple 10 %p-p max.)
[1] OPTIONS
DLR supported
blank: none
Port No.: 2222, 44818
/Q: With options (specify the specification)
I/O data size: One (1) word
Status indicator LEDs: MS, NS (Refer to the instruction
manual for details)
R7F4HEIP-DAC16B SPECIFICATIONS
ES-8005-D Rev.0 Page 1/5
https://www.m-system.co.jp/
MODEL: R7F4HEIP-DAC16B
INPUT SPECIFICATIONS
Common: Positive common (NPN), 8 points per common
STANDARDS & APPROVALS
EU conformity:
Numbers of input: 8 points
EMC Directive
Maximum inputs applicable at once: No limit (at 24 V DC)
Rated input voltage: 24 V DC ±10 %; ripple 5 %p-p max.
ON voltage / current: ≥ 15 V DC (X0 to X7 input teriminal –
+24 V) / ≥ 3.5 mA
EMI EN 61000-6-4
EMS EN 61000-6-2
RoHS Directive
OFF voltage / current: ≤ 5 V DC (X0 to X7 input teriminal –
+24 V) / ≤ 1.0 mA
PC CONFIGURATOR
The following parameters can be set with using PC
Configurator Software (model: R7CFG)
Refer to the users manual for the R7CFG for detailed
operation of the software program.
Input current: ≤ 5.5 mA per point at 24 V DC
Input resistance: Approx. 4.4 kΩ
ON delay: ≤ 0.2 msec.
OFF delay: ≤ 0.5 msec.
■ CHANNEL BATCH SETTING
PARAMETER
SETTING RANGE
1ms, 5ms, 10ms, 20ms,
50ms, 70ms, 100ms,
200ms
DEFAULT
10ms
Conversion rate
OUTPUT SPECIFICATIONS
Common: Positive common (PNP) per 8 points
Number of output: 8 points
Output Hold / Clear
Hold / Clear
Hold
Maximum outputs applicable at once: No limit (at 24 V DC)
Rated load voltage: 24 V DC ±10 %, ripple 5 %p-p max.
Rated output current: 0.1 A per point, 0.8 A per common
Residual voltage: ≤ 1.2 V
■ EtherNet SETTING
PARAMETER
SETTING RANGE
DEFAULT
IP Address
0.0.0.0 - 255.255.255.255
0.0.0.0 - 255.255.255.255
192.168.0.250
255.255.255.0
192.168.0.1
30 (0.1 sec.)
Subnet Mask
Leakage current: ≤ 0.1 mA
Default Gateway 0.0.0.0 - 255.255.255.255
TimeOut 0 - 32767 (0.1 sec.)
ON delay: ≤ 0.2 msec.
OFF delay: ≤ 0.5 msec.
Overload current protection function: Limits the current
value when overcurrent is detected
Overheat protection function: Turns OFF the outputs when
overheat is detected
(When driving an inductive load, connect a diode in parallel
with the load.)
INSTALLATION
Current consumption
•DC: Approx. 70 mA
(contact I/O load charge is not included)
Operating temperature: -10 to +55°C (14 to 131°F)
Storage temperature: -20 to +65°C (-4 to +149°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Atmosphere: No corrosive gas or heavy dust
Mounting: Surface or DIN rail (35 mm rail)
Weight: 170 g (0.37 lb)
PERFORMANCE
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 1500 V AC @ 1 minute
(input or exc. supply to output or exc. supply to EtherNet/IP
or FE to power)
R7F4HEIP-DAC16B SPECIFICATIONS
ES-8005-D Rev.0 Page 2/5
https://www.m-system.co.jp/
MODEL: R7F4HEIP-DAC16B
EXTERNAL VIEW
IP Address Setting Rotary SW
Status Indicator LED
PC Con!gurator Jack
RJ-45 Modular Jack
Discrete I/O Status Indicator LED
Power Supply Connector
Sensor Exc. / I/O Connectors
TERMINAL ASSIGNMENTS
■SENSOR EXC. / I/O CONNECTION
Applicable connector: DFMC0,5/13-ST-2,54 (Phoenix Contact) (included in the package)
Applicable wire size: 0.14
0.5mm2, stripped length 7mm
-
Recommended solderless terminal:
· AI0,14-6GY 0.14mm2 (Phoenix Contact)
· AI0,25-6YE 0.25mm2 (Phoenix Contact)
· A0,34-7 0.34mm2 (Phoenix Contact)
1
2
3
4
5
6
7
8
9 10 11 12 13 27 28 29 30 31 32 33 34 35 36 37 38 39
14 15 16 17 18 19 20 21 22 23 24 25 26 40 41 42 43 44 45 46 47 48 49 50 51 52
PIN No.
ID
FUNCTION
24V DC
Input 0
24V DC
0V
PIN No.
27
ID
FUNCTION
24V DC
Output 0
24V DC
0V
1
2
+24V1
X0
+24V2
Y0
28
3
+24V1
GND1
X2
29
+24V2
GND2
Y2
4
30
5
Input 2
24V DC
0V
31
Output 2
24V DC
0V
6
+24V1
GND1
X4
32
+24V2
GND2
Y4
7
33
8
Input 4
24V DC
0V
34
Output 4
24V DC
0V
9
+24V1
GND1
X6
35
+24V2
GND2
Y6
10
11
12
13
36
Input 6
24V DC
0V
37
Output 6
24V DC
0V
+24V1
GND1
38
+24V2
GND2
39
PIN No.
14
ID
FUNCTION
0V
PIN No.
40
ID
FUNCTION
0V
GND1
X1
GND2
Y1
15
Input 1
24V DC
0V
41
Output 1
24V DC
0V
16
+24V1
GND1
X3
42
+24V2
GND2
Y3
17
43
18
Input 3
24V DC
0V
44
Output 3
24V DC
0V
19
+24V1
GND1
X5
45
+24V2
GND2
Y5
20
46
21
Input 5
24V DC
0V
47
Output 5
24V DC
0V
22
+24V1
GND1
X7
48
+24V2
GND2
Y7
23
49
24
Input 7
24V DC
0V
50
Output 7
24V DC
0V
25
+24V1
GND1
51
+24V2
GND2
26
52
R7F4HEIP-DAC16B SPECIFICATIONS
ES-8005-D Rev.0 Page 3/5
https://www.m-system.co.jp/
MODEL: R7F4HEIP-DAC16B
■POWER SUPPLY TERMINAL ASSIGNMENT
Applicable connector: TFMC1,5 / 5–STF–3,5(Phoenix Contact)
(included in the package)
Applicable wire size: 0.2 − 1.5 mm2; stripped length 10 mm
Recommended solderless terminal
• AI0,25-10YE 0.25 mm2 (Phoenix Contact)
• AI0,34-10TQ 0.34 mm2 (Phoenix Contact)
• AI0,5-10WH 0.5 mm2 (Phoenix Contact)
• AI0,75-10GY 0.75 mm2 (Phoenix Contact)
• A1-10 1.0 mm2 (Phoenix Contact)
• A1,5-10 1.5 mm2 (Phoenix Contact)
1 2 3 4 5
1. FE
2. NC
3. NC
Functional Earth
—
—
4. +24V Power Input (
24V DC
)
5. 0V
Power Input ( )
0V
I/O DATA DESCRIPTIONS
■ DISCRETE INPUT
■ DISCRETE OUTPUT
15
0
0
15
Input 0
Input 1
Input 2
Input 3
Output 0
Output 1
Output 2
Output 3
Input 7
Output 7
0: OFF 1: ON
0: OFF 1: ON
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm
138 [5.43]
123 [4.84]
115 [4.53]
72 [2.83]
55 [2.17]
DIN rail
(35mm wide)
(4 [.16])
2-4.3 dia. 4 deep.
R7F4HEIP-DAC16B SPECIFICATIONS
ES-8005-D Rev.0 Page 4/5
https://www.m-system.co.jp/
MODEL: R7F4HEIP-DAC16B
MOUNTING REQUIREMENTS unit: mm [inch]
125 [4.92]
2-M4
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
Note: In order to improve EMC performance, bond the FE terminal to ground.
Caution: FE terminal is NOT a protective conductor terminal.
isolation
*1
29
30
28
+24V2
GND2
Y0
RJ-45 MODULAR JACK
RJ-45 MODULAR JACK
EtherNet/IP
OUTPUT Y0
*1
EtherNet/IP
isolation
51
52
50
+24V2
GND2
Y7
3
4
2
+24V1
GND1
X0
OUTPUT Y7
Detecting
Circuit
INPUT X０
Control
Circuit
27
+24V2
GND2
EXC. SUPPLY (IN)
40
25
26
24
+24V1
GND1
X7
Detecting
Circuit
INPUT X７
1
+24V1
GND1
EXC. SUPPLY (IN)
14
4
5
2
3
1
24V DC
0V
NC
NC
FE
*1. The network cable can be connected to either one.
Specifications are subject to change without notice.
R7F4HEIP-DAC16B SPECIFICATIONS
ES-8005-D Rev.0 Page 5/5
https://www.m-system.co.jp/
相关型号：
©2020 ICPDF网 联系我们和版权申明