D1U86G-W-460-12-HB4DC [MURATA]
AC-DC Regulated Power Supply Module, 460W;型号: | D1U86G-W-460-12-HB4DC |
厂家: | muRata |
描述: | AC-DC Regulated Power Supply Module, 460W 输出元件 |
文件: | 总5页 (文件大小:630K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
D1U86G-W-460-12-HxxDC Series
86mm 1U Front End AC-DC Power Supply Converter
s
PRODUCT OVERVIEW
The D1U86G-W-460-12-HxxDC is a bulk front end power supply which meets the needs of systems requiring high
efficiency distributed power architectures. The output power of this supply is rated at 460W with one main and one
standby output. The supply provides high efficiency performance, hot plug capability, and parallel operation with droop
current sharing. Closed-loop internal fan cooling provides reliable long life operation. Industry standard PMBus™
communication protocol makes system integration with this supply seamless and straightforward. The low-profile
design and dense packaging makes this supply ideal for delivering reliable, efficient power to servers, workstations,
storage devices and other distributed power systems.
ORDERING GUIDE
Part Number
Power Output
Main Output Standby Output
Airflow
FEATURES
460W output power
D1U86G-W-460-12-HB4DC
D1U86G-W-460-12-HB3DC
460W
460W
12V
12V
12V
12V
Back to front
Front to back
Exceeds 92% efficiency at 50% load
(230Vac Input)
INPUT CHARACTERISTICS
Parameter
Input Voltage Operating Range
Frequency
Turn-on Voltage
Turn-off Voltage
Maximum Input Current (100Vac)
Inrush Current
Power Factor
12V main output
Conditions
Min.
90
47
81
70.5
Nom.
115/230
50/60
85
Max.
264
63
Units
Vac
Hz
12V standby output of 30W
1U height: 3.4" x 7.75" x 1.57"
11.1 Watts per cubic inch density
Ramp up
Ramp down
460W
89
78
Vac
74.3
5.5
30
Arms
Apk
N+1 redundancy capable,
including hot plugging (up to 8 in parallel)
At 264Vac at 25°C cold start
At 230Vac, full load
20% load
0.99
Droop current sharing on 12V main output,
ORing FET
88
92
88
Efficiency (230Vac) excluding fan load
%
50% load
100% load
Overvoltage, overcurrent,
overtemperature protection
OUTPUT VOLTAGE CHARACTERISTICS
Internal cooling fan (variable speed)
PMBus™ / I²C interface with status indicators
RoHS compliant
Output
Voltage
Parameter
Conditions
1A load
Min.
Typ.
Max.
Units
Vdc
Voltage Set Point
Static Regulation
Ripple Voltage & Noise1 20MHz Bandwidth
Droop Regulation
12.27
11.85
12.3
12.33
12.45
120
0.33
38.3
mV p-p
V
A
Two-year warranty
12V
0.27
0
0.3
Output Current
Load Capacitance
Voltage Set Point
Line and Load Regulation
22,000
12.03
12.6
120
2.5
µF
11.97
11.4
12.0
Vdc
12VSB Ripple Voltage & Noise1 20MHz Bandwidth
Output Current
mV p-p
A
0
Load Capacitance
1000
µF
1
Ripple and noise are measured with 0.1 µF of ceramic capacitance and 10 µF of tantalum capacitance on each of
the power supply outputs. A short coaxial cable with 50Ω scope termination is used.
Available now at
www.murata-ps.com/en/3d/acdc.html
CB
PM
For full details go to
www.murata-ps.com/rohs
Test Certificate
and Test Report
www.murata-ps.com/support
D1U86G-W-460-12-HxxDC.B03 Page 1 of 5
D1U86G-W-460-12-HxxDC Series
86mm 1U Front End AC-DC Power Supply Converter
OUTPUT CHARACTERISTICS
Parameter
Conditions
Min.
Typ.
Max.
Units
Output Rise Monotonicity
Startup Time
No voltage excursion
AC ramp up
1.5
300
600
s
12V, 50% load step, 0.5A/μs di/dt
12VSB, 50% load step, 0.5A/μs di/dt
Transient Response
mV
Current sharing accuracy (up to 8 in parallel)
At 100% load
10
5
%
Hot Swap Transients
Holdup Time
All outputs remain in regulation
%
10
ms
ENVIRONMENTAL CHARACTERISTICS
Parameter
Conditions
Min.
-40
0
Typ.
Max.
70
Units
°C
Storage Temperature Range
Operating Temperature Range
Operating Humidity
50
Noncondensing
5
90
%
m
Storage Humidity
5
95
Altitude (without derating at 40°C)
Shock
3000
30G non operating
Operational Vibration
MTBF
1G, 10 – 500 Hz, 1.6G (non-operational)
Per Telcordia SR-322 M1C1 @ 40°C
635K
hrs
CSA/UL 60950-1-07-2nd Ed.
IEC 60950-1:2005 (2nd Edition) w Am. 1:2009
EN 60950-1:2006 +A11:2009 +A1:2010
CE Marking per LVD DIRECTIVE 2006/95/EC
Safety Approvals (pending)
Input Fuse
Weight
Power Supply has internal 6.3A/250V slow blow fuse on the AC line input
1.76 lbs (798g)
PROTECTION CHARACTERISTICS
Output
Parameter
Voltage
Conditions
Min.
Typ.
60
Max.
Units
Overtemperature (intake)
Autorestart
Latching
Latching
Autorecovery
Autorecovery
57
13.6
42
13.6
3.5
63
15
49.8
15
°C
V
A
V
A
Overvoltage
12V
Overcurrent
Overvoltage
12VSB
Overcurrent
5.0
ISOLATION CHARACTERISTICS
Parameter
Conditions
Input to Output - Reinforced
Input to Chassis - Basic
Min.
3000
1500
Typ.
Max.
Units
Vrms
Vrms
Insulation Safety Rating / Test Voltage
Isolation
Main and standby outputs connected directly to chassis
EMISSIONS AND IMMUNITY
Characteristic
Input Current Harmonics
Voltage Fluctuation and Flicker
Conducted Emissions
Standard
IEC/EN 61000-3-2
IEC/EN 61000-3-3
FCC 47 CFR Part 15/CISPR 22/EN55022
IEC/EN 61000-4-2
IEC/EN 61000-4-3
IEC/EN 61000-4-4
IEC/EN 61000-4-5
IEC/EN 61000-4-6
IEC/EN 61000-4-8
Compliance
Complies
Complies
Class B, 6dB margin
Level 3 criteria A
Level 3 criteria B
Level 3 criteria A
Level 3 criteria A
Level 3 criteria A
3 A/m criteria B
ESD Immunity
Radiated Field Immunity
Electrical Fast Transient Immunity
Surge Immunity
Radiated Field Conducted Immunity
Magnetic Field Immunity
230Vin, 100% load, Phase 0°, Dip 100% Duration 10ms (A)
230Vin, 50% load, Phase 0°, Dip 100% Duration 20ms (VSB:A, V1:A)
230Vin, 100% load, Phase 0°, Dip 100% Duration > 20ms (VSB, V1:B)
Voltage dips, interruptions
IEC/EN 61000-4-11
www.murata-ps.com/support
D1U86G-W-460-12-HxxDC.B03 Page 2 of 5
D1U86G-W-460-12-HxxDC Series
86mm 1U Front End AC-DC Power Supply Converter
STATUS INDICATORS AND CONTROL SIGNALS
Signal
Description
PSON#
Pulled low to enable main output
Present# signal must be pulled high through a resistor to enable the output, either to the PSU 12V bias output as shown in the wiring
diagram or to an external system bias output. The external system bias should be between 3.3V (5.1K pullup resistor) and 12V (10K
pullup resistor), with pullup resistors sized proportionally for voltages in between. The Present# signal can be used to communicate
the number of power supplies in the system (operational or non-operational). The signal is low when power supply is plugged into the
system, and is pulled up high when the power supply is unplugged. Present# is a short pin that results in a fast shut down signal to
turn off the main output and discharge the output capacitors when the supply is unplugged.
PRESENT#
PS INTERRUPT
PS ADDRESS LINES
IMON SIGNAL
Open drain PMBus™ signal
A0, A1, A2
Analog representation of main output current
AC input not OK and DC output not OK
AC input OK and DC output not OK
AC input OK and DC output OK
AC input not OK and DC output OK
I2C clock
PSOK Low (<0.6V)
PSOK Low (<0.6V)
PSOK
PSOK High (>0.6V)
PSOK Mid-Level (Less than 2.5V, Greater than 2V)
I2C CLOCK
I2C DATA
LED State
Off
I2C data
Mode
Operating Condition
AC Turn-off
Power-good
AC Input is below minimum power-supply turn-on specification or the main output is disabled and not delivering power
Power supply standby & main outputs are operating within normal parameters and delivering power
Green - solid
OUTPUT CONNECTOR AND SIGNAL SPECIFICATION
DC and Signal Connector: Gold Plated Card Edge Fingers
Power Supply Output Card Edge (Top Side)
Power Blades
PB1
PB2
PB3
PB4
PB5
PB6
PB7
PB8
PB9
PB10
Signal PIns
S1
Signal Name
Vo
Vo
Vo
RTN
RTN
RTN
RTN
RTN
Vo
PB5
PB4
PB3
PB2
PB1
S8
S1
Power Supply Output Card Edge (Bottom Side)
S9
S16
PB6
PB7
PB8
PB9
PB10
Vo
Signal Name
VSB
S2
VSB
S3
S4
S5
S6
S7
S8
S9
Reserved
PS INTERRUPT
PRESENT#
PSOK
IMON
PSON#
SCL
S10
S11
S12
S13
S14
S15
S16
SDA
GND
A0
A1
A2
RTN
RTN
www.murata-ps.com/support
D1U86G-W-460-12-HxxDC.B03 Page 3 of 5
D1U86G-W-460-12-HxxDC Series
86mm 1U Front End AC-DC Power Supply Converter
PERFORMANCE DATA
Efficiency
Thermal Derating
ꢃꢀ
8ꢃ
8ꢂ
ꢁꢁ
ꢁ1
6ꢀ
ꢄꢀꢀ
ꢃꢄꢀ
ꢃꢀꢀ
ꢂꢄꢀ
ꢂꢀꢀ
ꢁꢄꢀ
ꢁꢀꢀ
AC1ꢅꢄꢇ
ACꢅꢂꢄꢇ
ꢅꢀ to ꢁ6ꢃ ꢆꢇꢈ ꢉnput
1ꢄꢀ
1ꢀꢀ
ꢄꢀ
ꢀ
ꢄ
1ꢄ
ꢅꢄ
ꢂꢄ
ꢆꢄ
ꢀꢄ
6ꢄ
ꢁꢄ
8ꢄ
ꢃꢄ
1ꢄꢄ
ꢀ
1ꢀ
ꢁꢀ
ꢂꢀ
ꢃꢀ
ꢄꢀ
Load (%)
ꢉeꢊꢃerꢋꢂꢁre ꢇCꢈ
WIRING DIAGRAM FOR OUTPUT
Vo - Main output
Vo - Main Output
PB1, 2, 3, 9, 10
PB1, 2, 3, 9, 10
Main output
load
D1U86
D1U86
RTN
RTN
PB4-8
PB4-8
R1
R1
(12V) VSB
(12V) VSB S1-2
S1-2
PRESENT# S5
S5 PRESENT#
10K
10K
R2
1K
S8
1K
R2
PSON#
RTN
PSON#
S8
VSB load
FET, BJT, wire
FET, BJT, wire
or switch(debounced)
to turn on 12V main
output
or switch(debounced)
to turn on 12V main
output
RTN
NOTES
Main Output: Current share is achieved using the droop method. Nominal output voltage (12.30V) is achieved at 1A load and output voltage drops at a rate of 7.83mv per amp
increase. Startup of parallel power supplies is not internally synchronized. If more than 460W combined power is needed, start-up synchronization must be provided by using
a common PS_ON signal. To account for 10% full load current sharing accuracy and the reduction in full load output voltage due to droop, available output power must be
derated by 15% when units are operated in parallel. Internal ORing FETs are provided.
Standby output can be tied together for redundancy but total combined output power must not exceed 30W, Internal MOSFET ORing devices are used.
www.murata-ps.com/support
D1U86G-W-460-12-HxxDC.B03 Page 4 of 5
D1U86G-W-460-12-HxxDC Series
86mm 1U Front End AC-DC Power Supply Converter
MECHANICAL DIMENSIONS
Airflow Back to Front
Airflow Front to Back
AC input connector: IEC 320-C14
3.4"W x 7.75"L x 1.57"H [86.4mm x 196.85mm x 39.9mm]
MATING CONNECTOR
Part Number
Description
Molex 45984-1122
FCI 51761-10002406AA
Right Angle
Right Angle
OPTIONAL ACCESSORIES
Description
Part Number
12V D1U86G Output Connector Card
D1U86G-12-CONC
APPLICATION NOTES
Document Number
TBD
Description
D1U86G Output Connector Card
D1U86G Communication Protocol
TBD
This product is subject to the following operating requirements
and the Life and Safety Critical Application Sales Policy:
Refer to: http://www.murata-ps.com/requirements/
Murata Power Solutions, Inc.
11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A.
ISO 9001 and 14001 REGISTERED
Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other
technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply
the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without
notice.
© 2017 Murata Power Solutions, Inc.
www.murata-ps.com/support
D1U86G-W-460-12-HxxDC.B03 Page 5 of 5
相关型号:
©2020 ICPDF网 联系我们和版权申明