SFPKA450KH1A-R1 [MURATA]
Ceramic BPF, 0.45MHz, SMD, 3 PIN;型号: | SFPKA450KH1A-R1 |
厂家: | muRata |
描述: | Ceramic BPF, 0.45MHz, SMD, 3 PIN |
文件: | 总120页 (文件大小:2307K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr
(Filters/ Traps/ Discriminators)
for Audio/ Visual Equipment
Mu ra ta
Ma nu fa cturin g Co., Ltd .
Cat.No.P50E-1
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
1
CONTENTS
CERAFILr and "CERAFIL" in this catalog are
2
the trademarks of Murata Manufacturing Co., Ltd.
3
Part Numbering
2
6
4
1
2
CERAFILr 10.7MHz Small Chip Type SFECF Series
CERAFILr 10.7MHz Ultra Thin Chip Type SFECD Series
CERAFILr 10.7MHz Chip Type SFECV Series
CERAFILr 10.7MHz Standard Lead Type
CERAFILr 10.7MHz Low Loss Type
5
9
6
3
11
15
18
21
24
27
29
32
37
40
41
42
48
49
51
53
56
58
60
62
63
64
66
67
68
71
74
75
77
78
81
85
87
89
94
102
4
7
5
8
6
CERAFILr 10.7MHz Low Profile Type
9
7
CERAFILr 10.7MHz Low Spurious Response Type
CERAFILr 10.7MHz Wide Bandwidth Type
CERAFILr 10.7MHz Narrow Bandwidth Type
CERAFILr 10.7MHz for FM-IF Tuners
8
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
9
10
11
CERAFILr 10.7MHz High Selectivity Type SFTLF Series
CERAFILr 10.7MHz Related Data on Lead Type
12
13
14
15
16
17
18
19
20
21
CERAFILr 4.5-6.5MHz Chip Type SFSKA Series
CERAFILr 4.5-6.5MHz Standard Lead Type SFSRA Series
CERAFILr 3.5-6.5MHz for Chroma Signal SFSRA/ F Series
CERAFILr 455kHz Chip Type PFWCC Series
CERAFILr 455kHz Chip Type SFPKA Series
CERAFILr 455kHz SFULA/ SFZLA Series
CERAFILr 455kHz PFSLF/ PFWLF Series
CERAFILr 455kHz SFPLA/ CFWLA Series
CERAFILr 455kHz for AM Stereo Wide Bandwidth Type SFPLA/ CFWLA/ CFULA Series
CERAFILr 455kHz for AM Search-stop Signal Detection
CERAFILr 455kHz SF/PF Series Temperature Characteristics
CERAFILr 455kHz SF/PF/BF Series Application Circuit
22
23
24
25
26
27
28
29
30
Ceramic Trap 4.5-6.5MHz Chip Type TPSKA Series
Ceramic Trap 4.5-6.5MHz Chip Type Double Traps TPWKA Series
Ceramic Trap 4.5-6.5MHz Standard Lead Type TPSRA Series
Ceramic Trap 3.5-6.5MHz Two Lead Type TPSRF_J Series
Ceramic Trap 3.5-6.5MHz for 2ch Sound TV in Germany TPSRF_W Series
Ceramic Trap 3.5-6.5MHz Double Traps TPWRF Series
Ceramic Trap 3.5-6.5MHz Triple Traps TPTRF Series
Ceramic Discriminator 10.7MHz Ultra Thin Chip Type CDSCB Series
Ceramic Discriminator 10.7MHz Standard Lead Type CDALF Series
Ceramic Discriminator 10.7MHz Appllied IC Reference Table
31
Ceramic Discriminator 3.5-6.5MHz Wide Bandwidth Type CDSRF Series
Notice (Soldering and Mounting)
Notice (Handling)
Packaging
Recycled Paper
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
o Part Numbering
r
CERAFIL for FM
(Part Number)
SF
E
LF 10M7 FAA0 -B0
q
w
e
r
t
y
qProduct ID
tProduct Specification
Product ID
Product Specification
Code
SF
Ceramic Filters
Four-digit alphanumerics express
pass-bandwidth, center frequency tolerance,
rank, series, others.
FAA0
wOscillation/Numbers of Element
Oscillation/Numbers of Element
2 Elements Thickness Expander mode
3 Elements Thickness Expander mode
Code
yPackaging
E
T
Packaging
Bulk
Code
-B0
-R0
-R1
-A0
-A1
2 Elements Thickness Expander mode
(2nd Harmonic)
V
K
Plastic Taping ø180mm
Plastic Taping ø330mm
1500pcs. /Radial Taping H0=18mm
1000pcs. /Radial Taping H0=18mm
2 Elements Thickness Expander mode
(3rd Over Tone)
eStructure/Size
Radial taping is applied to lead type and plastic taping to chip type.
With non-standard products, two-digit alphanumerics indicating
Structure/Size
Lead Type
Code
Lp
"Individual Specification" is added between " Product Specification"
t
and " Packaging".
y
Chip Type
Cp
is expressed "A" or subsequent code, which indicates the
p
structure/size.
rNominal Center Frequency
Expressed by four-digit alphanumerics. The unit is in hertz (MHz).
Decimal point is expressed by capital letter "M".
r
CERAFIL for TV/VCR
(Part Number)
SF
S
RA 4M50 CF 00 -B0
q
w
e
r
t
y
u
qProduct ID
tProduct Specification Code (1)
Product ID
Product Specification Code (1)
Code
AF
SF
Ceramic Filters
Standard Bandwidth Type
Tight Bandwidth Type
BF
wOscillation/Numbers of Element
Standard Bandwidth Type
Broad Bandwidth Type
CF
Oscillation/Numbers of Element
Code
DF
2 Elements Thickness Shear mode
Ultra-broad Bandwidth Type
S
T
EF
The code AF is only applied to SFT series.
3 Elements Thickness Expander mode
eStructure/Size
yProduct Specification Code (2)
Structure/Size
Lead Type
Product Specification Code (2)
Code
Rp
Code
Standard Type
00
Chip Type
Kp
uPackaging
is expressed "A" or subsequent code, which indicates the
p
structure/size.
Packaging
Bulk
Code
-B0
rNominal Center Frequency
Radial Taping H0=18mm
Plastic Taping ø=330mm
-A0
Expressed by four-digit alphanumerics. The unit is in hertz (MHz).
Decimal point is expressed by capital letter "M".
-R1
Radial taping is applied to lead type and plastic taping to chip type.
With non-standard products, two-digit alphanumerics indicating
"Individual Specification" is added between " Product Specification
y
Code (2)" and " Packaging".
u
2
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
r
CERAFIL for AM
(Part Number)
PF
W
LF 450K P2A -B0
q
w
e
r
t
y
qProduct ID
tProduct Specification
Product ID
Product Specification
Code
PF
SF
CF
Ceramic Filters
Ceramic Filters
Ceramic Filters
Standard Type
P2A
A indicates standard type.
pp
yPackaging
wOscillation/Numbers of Element
Packaging
Bulk
Code
-B0
-R0
-R1
-A0
-M0
Oscillation/Numbers of Element
1 Element Length mode
Code
S
Plastic Taping (ø180mm)
Plastic Taping (ø330mm)
Radial Taping H0=18mm
Magazine Cassette
2 Elements Length mode
W
U
1 Element Area Expansion mode
2 Elements Area Expansion mode
4 Elements Area Expansion mode
Z
Radial taping is applied to lead type and plastic taping to chip type.
With non-standard products, three-digit alphanumerics indicating
P
"Individual Specification" is added between " Product Specification"
t
eStructure/Size
and " Packaging".
y
Structure/Size
Lead Type
Code
Lp
Chip Type
Cp
p is "A" or subsequent code, which indicates the structure/size. It
varies depending on vibration mode and number of elements.
rNominal Center Frequency
Expressed by four-digit alphanumerics. The unit is in hertz (Hz).
Capital letter "K" following three figures expresses the unit of
"kHz".
r
CERAFIL for Search-stop Signal Detection
(Part Number)
BF
U
LA 450K
C
-B0
q
w
e
r
t
y
qProduct ID
tProduct Specification
Product ID
Product Specification
Code
BF
Resonator
Bandwidth
Cp
With standard type, is omitted.
p
wOscillation/Numbers of Element
yPackaging
Oscillation/Numbers of Element
Code
1 Element Area Expansion mode
Packaging
U
Code
Bulk
-B0
eStructure/Size
Radial taping is applied to lead type and plastic taping to chip type.
With non-standard products, "Individual Specification (serial number)"
Structure/Size
Code
and "Lead Shape (Lead Bend : B)" are added between " Product
t
Lead Type Standard
LA
Specification" and " Package Specification Code" upon
y
specification.
rNominal Center Frequency
Nominal Center Frequency
Code
450kHz
450K
3
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Ceramic Traps
(Part Number)
TP
S
RA 4M50
B
00 -B0
q
w
e
r
t
y
u
qProduct ID
tProduct Specification Code (1)
Product ID
Product Specification (1)
Code
B
TP
Ceramic Traps
Broad-bandwidth Type
Low-capacitance Type
C
wFunction
yProduct Specification Code (2)
Function
Single Traps
Triple Traps
Double Traps
Code
S
Product Specification Code (2)
Code
Standard Type
T
00
W
uPackaging
eStructure/Size
Packaging
Bulk
Code
-B0
Structure/Size
Lead Type
Code
Rp
Radial Taping H0=18mm
Plastic Taping ø=330mm
-A0
Chip Type
Kp
-R1
is expressed "A" or subsequent code, which indicates the
structure/size.
Radial taping is applied to lead type and plastic taping to chip type.
With non-standard products, three-digit alphanumerics indicating
p
"Individual Specification" is added between " Product Specification
y
Code (2)" and " Packaging".
u
rNominal Center Frequency
Expressed by four-digit alphanumerics. The unit is in hertz (MHz).
Decimal point is expressed by capital letter "M".
Discriminators for FM
(Part Number)
CD
A
LF 10M7 GA 001 -B0
q
w
e
r
t
y
u
qProduct ID
tProduct Specification
Product ID
Product Specification
Code
CD
Discriminators
Two-digit alphanumerics express
type, center frequency, rank, others
GA
wOscillation
yIC
Oscillation
Code
A
Thickness Expander mode
Thickness Shear mode
IC
Code
Applicable IC Control Code
S
001
eStructure/Size
uPackaging
Structure/Size
Lead Type
Packaging
Bulk
Code
Lp
Code
-B0
-A0
-R0
-R1
Chip Type
Radial Taping H0=18mm
Plastic Taping ø=180mm
Plastic Taping ø=330mm
Cp
is expressed "A" or subsequent code, which indicates the
p
structure/size.
Radial taping is applied to lead type and plastic taping to chip type.
With non-standard products, an alphanumerics indicating "Individual
rNominal Center Frequency
Specification" is added between " IC" and " Packaging".
y
u
Expressed by four-digit alphanumerics . The unit is in hertz (MHz).
Decimal point is expressed by capital letter "M".
4
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Discriminators for TV/VCR
(Part Number)
CD
S
RF 4M50
E
K
048 -A0
q
w
e
r
t
y
u
i
qProduct ID
yProduct Specification Code (2)
Product ID
Product Specification Code (2)
Code
CD
Discriminators
Specification
K
wOscillation
uIC
Oscillation
IC
Code
Code
Thickness Shear mode
Applicable IC control code
S
048
eStructure/Size
iPackaging
Structure/Size
Packaging
Bulk
Code
Code
-B0
Lead Type
Rp
is expressed "A" or subsequent code, which indicates the
p
Radial Taping H0=18mm
-A0
structure/size.
With non-standard products, a letter Indicating "Individual
Specification" is added between " IC" and " Packaging".
u
i
rNominal Center Frequency
Expressed by four-digit alphanumerics. The unit is in hertz (MHz).
Decimal point is expressed by capital letter "M".
tProduct Specification Code (1)
Product Specification Code (1)
Three-terminals
Code
C
Two-terminals
E
5
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
1
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
CERAFILr 10.7MHz Small Chip Type SFECF Series
1.3±0.1
3.45±0.2
SFECF10M7 series for FM-receivers are small, high
Inputelectrode
marker
performance and super thin (1.4mm max.) filters.
Piezoelectric element is connected in the sandwich
shape by ceramics substrate.
(0.6)
(0.6)(0.6)
0 to 0.4
0 to 0.4
They have 1.4mm max. thickness and small mounting area.
(3.45x3.1mm)
(1.28)(1.28)
0.3 min. 0.3 min.
0.65±0.3 0.7±0.3 0.65±0.3
SFECF series and CDSCB series (MHz Discriminator)
enable customers to make VICS/RKE/TPMS set so thin and
small sized.
(1) : Input
(2)(5) : Ground
(3)(4) : No connect
(6) : Output
(1)
(6)
(3)
(4)
(2)
(5)
:
EIAJ Monthly Code
(
) : Reference
(1.28)(1.28)
0 to 0.35
(in mm)
0 to 0.35
■ Features
1. The filters are mountable by automatic placers.
2. They are slim, at only 1.4mm max. thickness, and
have a small mounting area (3.45x3.1mm) enabling
flexible PCB design.
3. Various bandwidths are available. Select a
suitable type in accordance with the desired
selectivity.
4. Operating temperature range: -20 to +80 (degree C)
Storage temperature range: -40 to +85 (degree C)
Center
Nominal Center
Insertion
Loss
(dB)
Spurious
Input/Output
3dB Bandwidth Attenuation
Ripple
Part Number
Frequency (fo) Frequency (fn)
Attenuation Impedance
(kHz)
(kHz)
(dB)
(MHz)
(MHz)
(dB)
(ohm)
SFECF10M7HA00-R0
SFECF10M7GA00-R0
SFECF10M7FA00-R0
SFECF10M7EA00-R0
SFECF10M7DF00-R0
10.700 ±30kHz
-
180 ±40kHz
230 ±50kHz
280 ±50kHz
330 ±50kHz
fn±150 min.
470 max.
510 max.
590 max.
700 max.
990 max.
4.0 ±2.0dB
3.5 ±2.0dB
1.0 max.
1.0 max.
1.0 max.
1.0 max.
3.0 max.
30 min.
330
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
-
-
30 min.
30 min.
30 min.
20 min.
330
330
330
330
-
3.0 ±2.0dB
-
3.0 ±2.0dB
10.700
6.0 max. [at fn]
Area of Attenuation: [within 20dB]
Area of Insertion Loss: at minimum loss point
Center frequency (fo) defined by the center of 3dB bandwidth.
Area of Spurious Attenuation: [within 9MHz to 12MHz]
Area of Ripple: within 3dB B.W.
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
■ Standard Center Frequency Rank Code
CODE
30kHz Step
25kHz Step
D
B
A
C
E
Z
10.64MHz±30kHz
10.67MHz±30kHz
10.70MHz±30kHz
10.73MHz±30kHz
10.76MHz±30kHz
10.650MHz±25kHz
10.675MHz±25kHz
10.700MHz±25kHz
10.725MHz±25kHz
10.750MHz±25kHz
Combination A, B, C, D, E
Combination A, B, C
M
Continued on the following page.
6
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Continued from the preceding page.
■ Standard Land Pattern Dimensions
■ Test Circuit
1
(3)
(2)
(4)
(5)
(6)
(5)
(4)
R1
(1)
(6)
Rg
RF
Voltmeter
E1
C2
R2
E2
(1)
(2)
(3)
S.S.G.
0.1
0.1
(1) : Input
(2)(5) : Ground
(3)(4) : No connect
(6) : Output
0.8 0.6 0.8 0.6 0.8
Rg = 50Ω R1 = 280Ω ±5% R2 = 330Ω ±5%
C2 = 10 ± 2 pF (Including stray capacitance and Input capacitance
of RF Volt Meter)
(1) : Input
(2)(5) : Ground
(3)(4) : No connect
(6) : Output
E1 : S.S.G. Output Voltage
It shows solder resist land pattern.
(in mm)
■ Frequency Characteristics
SFECF10M7HA00-R0
SFECF10M7GA00-R0
0
7.0
6.0
5.0
4.0
3.0
2.0
1.0
0
7.0
6.0
5.0
4.0
3.0
2.0
1.0
1
2
3
4
5
1
2
3
4
5
6
7
6
7
0.0
0.0
10.300
10.500
10.700
10.900
11.100
10.300
10.500
10.700
10.900
11.100
Frequency (MHz)
Frequency (MHz)
SFECF10M7FA00-R0
SFECF10M7EA00-R0
0
1
2
3
4
5
6
7.0
6.0
5.0
4.0
3.0
2.0
1.0
0
1
2
3
4
5
6
7.0
6.0
5.0
4.0
3.0
2.0
1.0
7
7
0.0
0.0
10.300
10.500
10.700
10.900
11.100
10.300
10.500
10.700
10.900
11.100
Frequency (MHz)
Frequency (MHz)
SFECF10M7DF00-R0
0
1
2
3
4
5
6
7.0
6.0
5.0
4.0
3.0
2.0
1.0
7
0.0
10.300
10.500
10.700
10.900
11.100
Frequency (MHz)
7
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Frequency Characteristics (Spurious)
1
SFECF10M7HA00-R0
SFECF10M7GA00-R0
0
0
10
20
30
40
50
60
10
20
30
40
50
60
70
70
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
12.700
12.700
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
SFECF10M7FA00-R0
SFECF10M7EA00-R0
0
10
20
30
40
50
60
0
10
20
30
40
50
60
70
8.700
70
8.700
9.700
10.700
Frequency (MHz)
11.700
9.700
10.700
Frequency (MHz)
11.700
12.700
SFECF10M7DF00-R0
0
10
20
30
40
50
60
70
8.700
9.700
10.700
11.700
Frequency (MHz)
8
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
2
CERAFILr 10.7MHz Ultra Thin Chip Type SFECD Series
1.0 max.
3.45±0.2
SFECD10M7 series for FM-receivers are small, high
performance and ultra thin (1.0mm max.) filters.
Piezoelectric element is connected in the sandwich
(0.6)
(0.6)(0.6)
0 to 0.4
0 to 0.4
shape by very thin ceramics substrate.
They have 1.0mm max. thickness and small mounting area.
(3.45x3.1mm)
(1.28)(1.28)
(1) : Input
0.65±0.3 0.55±0.3 0.65±0.3
(2)(5) : Ground
(3)(4) : No Connect
(6) : Output
SFECD series enable customers to make RF modules so
thin and small sized.
(2)
(5)
(1)
(6)
(3)
(4)
:
:
:
Marking
EIAJ Monthly Code
Center Frequency
Rank Code
(1.28)(1.28)
0 to 0.35
■ Features
(
) : Reference
0 to 0.35
(in mm)
1. The filters are mountable by automatic placers.
2. They are slim, at only 1.0mm max. thickness, and
have a small mounting area (3.45x3.1mm) enabling
flexible PCB design.
3. Operating temperature range: -20 to +80 (degree C)
Storage temperature range: -40 to +85 (degree C)
■ Applications
1. Card type radios
2. Card type RKE modules
3. Card type PHS modules
Center
Frequency (fo)
(MHz)
Insertion
Loss
(dB)
Spurious
Attenuation
(dB)
Input/Output
Impedance
(ohm)
3dB Bandwidth
(kHz)
Attenuation
Ripple
(dB)
Part Number
(kHz)
SFECD10M7FA00-R0
10.700 ±30kHz
280 ±50kHz
590 max.
3.0 ±2.0dB
1.0 max.
30 min.
330
Area of Attenuation: [within 20dB]
Area of Spurious Attenuation: [within 9MHz to 12MHz]
Area of Ripple: within 3dB B.W.
Center frequency (fo) defined by the center of 3dB bandwidth.
Area of Insertion Loss: at minimum loss point
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
■ Standard Center Frequency Rank Code
CODE
30kHz Step
25kHz Step
D
B
A
C
E
Z
10.64MHz±30kHz
10.67MHz±30kHz
10.70MHz±30kHz
10.73MHz±30kHz
10.76MHz±30kHz
10.650MHz±25kHz
10.675MHz±25kHz
10.700MHz±25kHz
10.725MHz±25kHz
10.750MHz±25kHz
Combination A, B, C, D, E
Combination A, B, C
M
Continued on the following page.
9
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Continued from the preceding page.
■ Standard Land Pattern Dimensions
■ Test Circuit
2
(3)
(2)
(4)
(5)
(6)
(5)
(4)
R1
(1)
(6)
Rg
E1
R2
C2
E2
S.S.G.
RF
Voltmeter
(1)
(2)
(3)
0.1
0.1
(1) : Input
(1) : Input
(2)(5) : Ground
(3)(4) : Float (Signal Line)
(6) : Output
(2)(5) : Ground
(3)(4) : Float
(6) : Output
0.8 0.5 0.8 0.5 0.8
R1+Rg=R2=330Ω±5%, Rg=50Ω
C2=10pF (Including stray capacitance and Input capacitance of RF Voltmeter)
E1 : S.S.G. Output Voltage
It shows solder resist land pattern.
(in mm)
■ Frequency Characteristics
■ Frequency Characteristics (Spurious)
SFECD10M7FA00-R0
SFECD10M7FA00-R0
0
7
6
5
4
3
2
1
0
10
20
30
40
50
60
70
1
2
3
4
5
6
7
8.700
9.700
10.700
11.700
12.700
0
Frequency (MHz)
10.300
10.500
10.700
10.900
11.100
Frequency (MHz)
10
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
CERAFILr 10.7MHz Chip Type SFECV Series
3
6.9±0.3
1.2±0.3
4.05±0.4
SFECV10M7 series for FM-receivers are monolithic type
1.2±0.5
1.5±0.2
1.2±0.5
ceramic filters which utilize the thickness expander
mode of the piezoelectric ceramic. SFECV series and
PFWCC (kHz filter for AM receiver) enable customers to
make AM/FM set so thin, and it can be of help to the
total chip circuit.
*
*ꢀ
*
(3)
(2)
(1)
:
Marking
(1) : Input
(2) : Ground
(3) : Output
■ Features
1.0±0.5
1.0±0.5
1.0±0.5
1. Piezoelectric element is connected in the sandwich
shape by heat resistant substrate, thus it has
excellent mechanical strength, and it is
suitable for automatic mounting.
** : EIAJ Monthly Code
** : Center Frequency Rank Code
(in mm)
2. Various bandwidths are available. Select a suitable
type in accordance with the desired selectivity.
■ Applications
1. Small, thin radios
2. Automotive radios
3. Headphone stereos
Center
Frequency (fo)
(MHz)
Insertion
Loss
(dB)
Spurious
Attenuation
(dB)
Input/Output
Impedance
(ohm)
3dB Bandwidth
(kHz)
Attenuation
(kHz)
Part Number
SFECV15M0EQ0001-R0
SFECV10M7KA00-R0
SFECV10M7JA00-R0
SFECV10M7HA00-R0
SFECV10M7GA00-R0
SFECV10M7FA00-R0
SFECV10M7CQ0C01-R0
SFECV10M7DF0021-R0
15.000 ±50kHz
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
10.700 ±40kHz
-
300 min.
750 max.
320 max.
380 max.
470 max.
510 max.
590 max.
950 max.
950 max.
7.0 max.
6.0 ±2.0dB
5.5 ±2.0dB
4.0 ±2.0dB
3.5 ±2.0dB
3.0 ±2.0dB
2.0 +2.0/-1.0dB
3.0 ±2.0dB
30 min.
35 min.
35 min.
35 min.
35 min.
35 min.
20 min.
20 min.
330
330
330
330
330
330
470
470
110 ±30kHz
150 ±40kHz
180 ±40kHz
230 ±50kHz
280 ±50kHz
500 ±40kHz
fn±175 min.
Area of Attenuation: [within 20dB]
Area of Spurious Attenuation: [within 9MHz to 12MHz], SFECV15M0EQ0001-R0: [within 14MHz to fo/fo to 16MHz], SFECV10M7CQ0C01-R0: [within 5MHz to 12MHz]
Area of Insertion Loss: at minimum loss point
Center frequency (fo) defined by the center of 3dB bandwidth.
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
■ Standard Center Frequency Rank Code
CODE
30kHz Step
25kHz Step
D
B
A
C
E
Z
10.64MHz±30kHz
10.67MHz±30kHz
10.70MHz±30kHz
10.73MHz±30kHz
10.76MHz±30kHz
10.650MHz±25kHz
10.675MHz±25kHz
10.700MHz±25kHz
10.725MHz±25kHz
10.750MHz±25kHz
Combination A, B, C, D, E
Combination A, B, C
M
Continued on the following page.
11
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Continued from the preceding page.
■ Standard Land Pattern Dimensions
1.2
1.2
1.2
3
1.65
2.85
1.65
2.85
Land
(in mm)
■ Test Circuit
SFECV10M7_A00-R0
SFECV10M7CQ0C01-R0
SFECV10M7DF0021-R0
R1
R1
(1)
(3)
R2
(1)
(3)
(2)
(2)
Rg
Rg
RF
Voltmeter
RF
Voltmeter
E1
E1
C2
C2
E2
R2
E2
S.S.G.
=-10dBm
S.S.G.
Rg = 50Ω R1 = 280Ω ±5% R2 = 330Ω ±5%
Rg = 50Ω R1 = 420Ω ±5% R2 = 470Ω ±5%
(1) : Input
(1) : Input
C2 = 10 ± 2 pF (Including stray capacitance and Input capacitance
of RF Volt Meter)
E1 : S.S.G. Output Voltage
C2 = 10 ± 2 pF (Including stray capacitance and Input capacitance
of RF Volt Meter)
E1 : S.S.G. Output Voltage
(2) : Ground
(3) : Output
(2) : Ground
(3) : Output
SFECV15M0EQ0001-R0
R1
(1)
(3)
R2
(2)
Rg
RF
Voltmeter
E1
C2
E2
S.S.G.
=-10dBm
Rg = 50Ω R1 = 280Ω ±5% R2 = 330Ω ±5%
(1) : Input
C2 = 10 ± 2 pF (Including stray capacitance and Input capacitance
of RF Volt Meter)
E1 : S.S.G. Output Voltage
(2) : Ground
(3) : Output
12
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Frequency Characteristics
SFECV10M7KA00-R0
SFECV10M7JA00-R0
0
1
2
3
4
5
6
7.0
6.5
6.0
5.5
5.0
4.5
4.0
0
1
2
3
4
5
6
8.0
7.5
7.0
6.5
6.0
5.5
5.0
3
7
7
3.5
4.5
10.300
10.500
10.700
10.900
11.100
10.300
10.500
10.700
10.900
11.100
Frequency (MHz)
Frequency (MHz)
SFECV10M7HA00-R0
SFECV10M7GA00-R0
0
1
2
3
4
5
6
6.0
5.5
5.0
4.5
4.0
3.5
3.0
0
1
2
3
4
5
6
5.5
5.0
4.5
4.0
3.5
3.0
2.5
7
7
2.5
2.0
10.300
10.500
10.700
10.900
11.100
10.300
10.500
10.700
10.900
11.100
Frequency (MHz)
Frequency (MHz)
SFECV10M7FA00-R0
SFECV10M7DF0021-R0
0
1
2
3
4
5
6
5.0
4.5
4.0
3.5
3.0
2.5
2.0
0
1
2
3
4
5
6
8.0
7.0
6.0
5.0
4.0
3.0
2.0
7
7
1.5
1.0
10.300
10.500
10.700
10.900
11.100
10.300
10.500
10.700
10.900
11.100
Frequency (MHz)
Frequency (MHz)
SFECV10M7CQ0C01-R0
SFECV15M0EQ0001-R0
0
1
2
3
4
5
6
7.0
6.0
5.0
4.0
3.0
2.0
0
2
4
6
8
10.0
8.0
6.0
4.0
2.0
7
1.0
10
0.0
10.300
10.500
10.700
10.900
11.100
14.700
14.800
14.900
15.000
15.100
15.200
15.300
Frequency (MHz)
Frequency (MHz)
13
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Frequency Characteristics (Spurious)
SFECV10M7KA00-R0
SFECV10M7JA00-R0
0
10
20
30
40
50
60
0
10
20
30
40
50
3
60
70
70
8.700
9.700
10.700
11.700
12.700
8.700
9.700
10.700
11.700
12.700
Frequency (MHz)
Frequency (MHz)
SFECV10M7HA00-R0
SFECV10M7GA00-R0
0
10
20
30
40
50
0
10
20
30
40
50
60
60
70
70
8.700
9.700
10.700
11.700
12.700
8.700
9.700
10.700
11.700
12.700
Frequency (MHz)
Frequency (MHz)
SFECV10M7FA00-R0
SFECV10M7DF0021-R0
0
10
20
30
40
50
60
0
10
20
30
40
50
60
70
8.700
70
8.700
9.700
10.700
11.700
12.700
9.700
10.700
11.700
12.700
Frequency (MHz)
Frequency (MHz)
SFECV10M7CQ0C01-R0
SFECV15M0EQ0001-R0
0
10
20
30
40
50
60
70
0
10
20
30
40
50
60
70
8.700
80
13.000
9.700
10.700
Frequency (MHz)
11.700
12.700
14.000
15.000
16.000
17.000
Frequency (MHz)
14
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
CERAFILr 10.7MHz Standard Lead Type
4
7.0±2.0
SFELF10M7 series for FM-receivers are monolithic type
ceramic filters which use the thickness expander mode
of the piezoelectric ceramic.
M A R K I N G
E I A J
C O D E
1.38±0.2
1.7±0.1
■ Features
1. These miniature filters have high mechanical
0.5±0.1
strength.
2.5±0.2 2.5±0.2
2. Low loss, favorable waveform symmetry, and high
(1) : Input
(2) : Ground
(3) : Output
selectivity
SFELF10M7HA00-B0
SFELF10M7GA00-B0
SFELF10M7FA00-B0
3. Various band widths are available for applications
in wide to narrow bands.
(in mm)
(3)
(2)
(1)
4. Small dispersion and stable characteristics
5. Change in center frequency is typically within
+-30ppm/(degree C) at -20 to +80 (degree C).
6. High reliability
7.0±2.0
M A R K I N G
E I A J
C O D E
1.38±0.2
1.7±0.1
0.5±0.1
2.5±0.2 2.5±0.2
(1) : Input
(2) : Ground
(3) : Output
(in mm)
(3)
(2)
(1)
7.0±2.0
M A R K I N G
E I A J
C O D E
1.38±0.2
1.7±0.1
0.5±0.1
2.5±0.2 2.5±0.2
(1) : Input
(2) : Ground
(3) : Output
(in mm)
(3)
(2)
(1)
Center
Frequency (fo)
(MHz)
Insertion
Loss
(dB)
Spurious
Attenuation
(dB)
Input/Output
Impedance
(ohm)
3dB Bandwidth
(kHz)
Attenuation
(kHz)
Part Number
SFELF10M7HA00-B0
SFELF10M7GA00-B0
SFELF10M7FA00-B0
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
180 ±40kHz
230 ±50kHz
280 ±50kHz
520 max.
570 max.
650 max.
7.0 max.
4.0 ±2.0dB
4.0 ±2.0dB
40 min.
40 min.
30 min.
330
330
330
Area of Attenuation: [within 20dB]
Area of Spurious Attenuation: [within 9MHz to 12MHz]
Area of Insertion Loss: at minimum loss point
Center frequency (fo) defined by the center of 3dB bandwidth.
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
15
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Standard Center Frequency Rank Code
CODE
30kHz Step
25kHz Step
10.650MHz±25kHz
10.675MHz±25kHz
10.700MHz±25kHz
10.725MHz±25kHz
10.750MHz±25kHz
Combination A, B, C, D, E
Combination A, B, C
Color Code
Black
D
B
A
C
E
Z
10.64MHz±30kHz
10.67MHz±30kHz
10.70MHz±30kHz
10.73MHz±30kHz
10.76MHz±30kHz
Blue
Red
Orange
White
4
M
■ Test Circuit
(1) (2) (3)
R1
RF
Rg
Voltmeter
C
R2
S.S.G
Rg + R1 = R2 = Input and Output Impedance
C = 10pF (Including stray capacitance and input
capacitance of RF voltmeter.)
(1) : Input
(2) : Ground
(3) : Output
■ Frequency Characteristics
SFELF10M7HA00-B0
SFELF10M7GA00-B0
0
1
2
3
4
5
6
6.5
0
1
2
3
4
5
6
6.0
5.5
5.0
4.5
4.0
3.5
3.0
6.0
5.5
5.0
4.5
4.0
3.5
7
7
3.0
2.5
10.500
10.600
10.700
10.800
10.900
10.500
10.600
10.700
10.800
10.900
Frequency (MHz)
Frequency (MHz)
SFELF10M7FA00-B0
0
1
2
3
4
5
6
5.5
5.0
4.5
4.0
3.5
3.0
2.5
7
2.0
10.500
10.600
10.700
10.800
10.900
Frequency (MHz)
16
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Frequency Characteristics (Spurious)
SFELF10M7HA00-B0
SFELF10M7GA00-B0
0
0
10
20
30
40
50
60
10
20
30
40
50
60
70
4
70
8.700
9.700
10.700
11.700
12.700
8.700
9.700
10.700
11.700
12.700
Frequency (MHz)
Frequency (MHz)
SFELF10M7FA00-B0
0
10
20
30
40
50
60
70
8.700
9.700
10.700
11.700
12.700
Frequency (MHz)
17
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
CERAFILr 10.7MHz Low Loss Type
7.0±2.0
SFELF10M7 series for FM-receivers are monolithic type
ceramic filters which use the thickness expander mode
of the piezoelectric ceramic.
5
M A R K I N G
E I A J
C O D E
1.38±0.2
1.7±0.1
■ Features
1. Insertion loss is 1 to 1.5dB lower than
conventional products. These types are useful for
elevating the sensitivity of sets.
0.5±0.1
2.5±0.2 2.5±0.2
(1) : Input
(2) : Ground
(3) : Output
2. Small dispersion and stable characteristics
3. Excellent shape factor of frequency response
4. Good waveform symmetry
SFELF10M7JAA0-B0
SFELF10M7HAA0-B0
SFELF10M7FAA0-B0
(in mm)
(3)
(2)
(1)
7.0±2.0
M A R K I N G
E I A J
C O D E
1.38±0.2
1.7±0.1
0.5±0.1
2.5±0.2 2.5±0.2
(1) : Input
(2) : Ground
(3) : Output
(in mm)
(3)
(2)
(1)
7.0±2.0
7.0±2.0
M A R K I N G
M A R K I N G
E I A J
C O D E
E I A J
C O D E
1.38±0.2
1.7±0.1
1.38±0.2
1.7±0.1
0.5±0.1
0.5±0.1
2.5±0.2 2.5±0.2
2.5±0.2 2.5±0.2
(1) : Input
(2) : Ground
(3) : Output
(1) : Input
(2) : Ground
(3) : Output
SFELF10M7GAA0-B0
(in mm)
(in mm)
(3)
(2)
(1)
(3)
(2)
(1)
Center
Frequency (fo)
(MHz)
Insertion
Loss
(dB)
Spurious
Attenuation
(dB)
Input/Output
Impedance
(ohm)
3dB Bandwidth
(kHz)
Attenuation
(kHz)
Part Number
SFELF10M7JAA0-B0
SFELF10M7HAA0-B0
SFELF10M7GAA0-B0
SFELF10M7FAA0-B0
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
150 ±40kHz
180 ±40kHz
230 ±50kHz
280 ±50kHz
360 max.
470 max.
520 max.
590 max.
4.5 ±2.0dB
3.5 ±1.5dB
3.0 ±2.0dB
2.5 ±2.0dB
35 min.
35 min.
35 min.
30 min.
330
330
330
330
Area of Attenuation: [within 20dB]
Area of Spurious Attenuation: [within 9MHz to 12MHz]
Area of Insertion Loss: at minimum loss point
Center frequency (fo) defined by the center of 3dB bandwidth.
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
18
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Standard Center Frequency Rank Code
CODE
30kHz Step
25kHz Step
10.650MHz±25kHz
10.675MHz±25kHz
10.700MHz±25kHz
10.725MHz±25kHz
10.750MHz±25kHz
Combination A, B, C, D, E
Combination A, B, C
Color Code
Black
D
B
A
C
E
Z
10.64MHz±30kHz
10.67MHz±30kHz
10.70MHz±30kHz
10.73MHz±30kHz
10.76MHz±30kHz
Blue
Red
Orange
White
5
M
■ Test Circuit
(1) (2) (3)
R1
RF
Rg
Voltmeter
C
R2
S.S.G
Rg + R1 = R2 = Input and Output Impedance
C = 10pF (Including stray capacitance and input
capacitance of RF voltmeter.)
(1) : Input
(2) : Ground
(3) : Output
■ Frequency Characteristics
SFELF10M7JAA0-B0
SFELF10M7HAA0-B0
0
1
2
3
4
5
6
7.0
0
1
2
3
4
5
6
6.5
6.0
5.5
5.0
4.5
4.0
3.5
6.5
6.0
5.5
5.0
4.5
4.0
7
7
3.5
3.0
10.500
10.600
10.700
10.800
10.900
10.500
10.600
10.700
10.800
10.900
Frequency (MHz)
Frequency (MHz)
SFELF10M7GAA0-B0
SFELF10M7FAA0-B0
0
1
2
3
4
5
6
6.0
5.5
5.0
4.5
4.0
3.5
3.0
0
1
2
3
4
5
6
5.5
5.0
4.5
4.0
3.5
3.0
2.5
7
7
2.5
2.0
10.500
10.600
10.700
10.800
10.900
10.500
10.600
10.700
10.800
10.900
Frequency (MHz)
Frequency (MHz)
19
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Frequency Characteristics (Spurious)
SFELF10M7JAA0-B0
SFELF10M7HAA0-B0
0
0
10
20
30
40
50
60
10
20
30
40
50
60
70
5
70
8.700
9.700
10.700
11.700
12.700
8.700
9.700
10.700
11.700
12.700
Frequency (MHz)
Frequency (MHz)
SFELF10M7GAA0-B0
SFELF10M7FAA0-B0
0
10
20
30
40
50
60
0
10
20
30
40
50
60
70
70
8.700
9.700
10.700
11.700
12.700
8.700
9.700
10.700
11.700
12.700
Frequency (MHz)
Frequency (MHz)
20
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
CERAFILr 10.7MHz Low Profile Type
7.5±2.0
SFELG10M7 series for FM-receivers are monolithic type
ceramic filters which use the thickness expander mode
of the piezoelectric ceramic.
E I A J
C O D E
M A R K I N G
6
1.5±0.1
1.3±0.1
■ Features
1. Installed height is 6.0mm, making it well suited
0.5±0.1
for compact, thin sets.
2.5±0.2 2.5
±0.2
2. Environmental reliability is the same as those of
(1) : Input
(2) : Ground
(3) : Output
the ceramic filter SFELF10M7 series.
SFELG10M7KA00-B0
SFELG10M7HA00-B0
SFELG10M7FA00-B0
in mm
(1)
(2)
(3)
7.5±2.0
7.5±2.0
E I A J
C O D E
E I A J
C O D E
M A R K I N G
M A R K I N G
1.5±0.1
1.3±0.1
1.5±0.1
1.3±0.1
0.5±0.1
0.5±0.1
2.5
±
0.2 2.5
±
0.2
2.5±0.2 2.5
±0.2
(1) : Input
(2) : Ground
(3) : Output
(1) : Input
(2) : Ground
(3) : Output
SFELG10M7JA00-B0
in mm
in mm
(1)
(2)
(3)
(1)
(2)
(3)
7.5±2.0
7.5±2.0
E I A J
C O D E
E I A J
C O D E
M A R K I N G
M A R K I N G
1.5±0.1
1.3±0.1
1.5±0.1
1.3±0.1
0.5±0.1
0.5±0.1
2.5
±
0.2 2.5
±
0.2
2.5±0.2 2.5
±0.2
(1) : Input
(2) : Ground
(3) : Output
(1) : Input
(2) : Ground
(3) : Output
SFELG10M7GA00-B0
in mm
in mm
(1)
(2)
(3)
(1)
(2)
(3)
Center
Frequency (fo)
(MHz)
Insertion
Loss
(dB)
Spurious
Attenuation
(dB)
Input/Output
Impedance
(ohm)
3dB Bandwidth
(kHz)
Attenuation
(kHz)
Part Number
SFELG10M7KA00-B0
SFELG10M7JA00-B0
SFELG10M7HA00-B0
SFELG10M7GA00-B0
SFELG10M7FA00-B0
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
110 ±30kHz
150 ±40kHz
180 ±40kHz
230 ±50kHz
280 ±50kHz
350 max.
360 max.
470 max.
570 max.
650 max.
7.0 ±2.0dB
4.5 ±2.0dB
3.5 ±2.0dB
3.0 ±2.0dB
3.0 ±2.0dB
30 min.
35 min.
35 min.
40 min.
30 min.
330
330
330
330
330
Area of Attenuation: [within 20dB]
Area of Spurious Attenuation: [within 9MHz to 12MHz]
Area of Insertion Loss: at minimum loss point
Center frequency (fo) defined by the center of 3dB bandwidth.
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
21
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Standard Center Frequency Rank Code
CODE
30kHz Step
25kHz Step
10.650MHz±25kHz
10.675MHz±25kHz
10.700MHz±25kHz
10.725MHz±25kHz
10.750MHz±25kHz
Combination A, B, C, D, E
Combination A, B, C
Color Code
Black
D
B
A
C
E
Z
10.64MHz±30kHz
10.67MHz±30kHz
10.70MHz±30kHz
10.73MHz±30kHz
10.76MHz±30kHz
Blue
Red
Orange
White
M
6
■ Test Circuit
(1) (2) (3)
R1
RF
Rg
Voltmeter
C
R2
S.S.G
Rg + R1 = R2 = Input and Output Impedance
C = 10pF (Including stray capacitance and input
capacitance of RF voltmeter.)
(1) : Input
(2) : Ground
(3) : Output
■ Frequency Characteristics
SFELG10M7KA00-B0
SFELG10M7JA00-B0
0
1
2
3
4
5
6
8.0
0
1
2
3
4
5
6
7.5
7.0
6.5
6.0
5.5
5.0
4.5
7.5
7.0
6.5
6.0
5.5
5.0
7
4.5
7
4.0
10.500
10.600
10.700
10.800
10.900
10.500
10.600
10.700
10.800
10.900
Frequency (MHz)
Frequency (MHz)
SFELG10M7HA00-B0
SFELG10M7GA00-B0
0
1
2
3
4
5
6
6.5
6.0
5.5
5.0
4.5
4.0
3.5
0
1
2
3
4
5
6
6.0
5.5
5.0
4.5
4.0
3.5
3.0
7
7
3.0
2.5
10.500
10.600
10.700
10.800
10.900
10.500
10.600
10.700
10.800
10.900
Frequency (MHz)
Frequency (MHz)
Continued on the following page.
22
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Continued from the preceding page.
■ Frequency Characteristics
SFELG10M7FA00-B0
0
1
2
3
4
5
6
5.5
5.0
4.5
4.0
3.5
3.,0
2.5
2.0
6
7
10.500
10.600
10.700
10.800
10.900
Frequency (MHz)
■ Frequency Characteristics (Spurious)
SFELG10M7KA00-B0
SFELG10M7JA00-B0
0
0
10
20
30
40
50
60
10
20
30
40
50
60
70
70
8.700
9.700
10.700
11.700
12.700
8.700
9.700
10.700
11.700
12.700
Frequency (MHz)
Frequency (MHz)
SFELG10M7HA00-B0
SFELG10M7GA00-B0
0
10
20
30
40
50
60
70
0
10
20
30
40
50
60
70
8.700
9.700
10.700
11.700
12.700
8.700
9.700
10.700
11.700
12.700
Frequency (MHz)
Frequency (MHz)
SFELG10M7FA00-B0
0
10
20
30
40
50
60
70
8.700
9.700
10.700
11.700
12.700
Frequency (MHz)
23
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
CERAFILr 10.7MHz Low Spurious Response Type
7.5±2.0
SFELF10M7 series for FM-receivers are monolithic type
ceramic filters which use the thickness expander mode
of the piezoelectric ceramic.
MARKING
EIAJ
CODE
7
1.38±0.2
1.7±0.1
■ Features
These types have lower spurious response compared
0.5±0.1
to the standard filters.
2.5±0.2 2.5±0.2
SFELF10M7KAB0-B0
(3)
(2)
(1)
(in mm)
(in mm)
(in mm)
7.5±2.0
7.5±2.0
MARKING
MARKING
EIAJ
EIAJ
CODE
CODE
1.38±0.2
1.7±0.1
1.38±0.2
1.7±0.1
0.5±0.1
0.5±0.1
2.5±0.2 2.5±0.2
2.5±0.2 2.5±0.2
SFELF10M7JAB0-B0
SFELF10M7HAB0-B0
(3)
(2)
(1)
(3)
(2)
(1)
(in mm)
7.5±2.0
7.5±2.0
MARKING
MARKING
EIAJ
EIAJ
CODE
CODE
1.38±0.2
1.7±0.1
1.38±0.2
1.7±0.1
0.5±0.1
0.5±0.1
2.5±0.2 2.5±0.2
2.5±0.2 2.5±0.2
SFELF10M7GAB0-B0
SFELF10M7FAB0-B0
(3)
(2)
(1)
(3)
(2)
(1)
(in mm)
Center
Frequency (fo)
(MHz)
Insertion
Loss
(dB)
Spurious
Attenuation
(dB)
Input/Output
Impedance
(ohm)
3dB Bandwidth
(kHz)
Attenuation
(kHz)
Part Number
SFELF10M7KAB0-B0
SFELF10M7JAB0-B0
SFELF10M7HAB0-B0
SFELF10M7GAB0-B0
SFELF10M7FAB0-B0
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
110 ±30kHz
150 ±40kHz
180 ±40kHz
230 ±50kHz
280 ±50kHz
350 max.
380 max.
520 max.
570 max.
650 max.
7.0 ±2.0dB
5.5 ±2.0dB
5.0 ±2.0dB
3.0 ±2.0dB
3.0 ±2.0dB
45/30 min.
45 min.
45 min.
45 min.
45 min.
330
330
330
330
330
Area of Attenuation: [within 20dB]
Area of Spurious Attenuation: [within 9MHz to 12MHz], SFELF10M7KAB0-B0: [within 9MHz to fo/fo to 12MHz]
Area of Insertion Loss: at minimum loss point
Center frequency (fo) defined by the center of 3dB bandwidth.
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
24
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Standard Center Frequency Rank Code
CODE
30kHz Step
25kHz Step
10.650MHz±25kHz
10.675MHz±25kHz
10.700MHz±25kHz
10.725MHz±25kHz
10.750MHz±25kHz
Combination A, B, C, D, E
Combination A, B, C
Color Code
Black
D
B
A
C
E
Z
10.64MHz±30kHz
10.67MHz±30kHz
10.70MHz±30kHz
10.73MHz±30kHz
10.76MHz±30kHz
Blue
Red
Orange
White
M
■ Test Circuit
7
(1) (2) (3)
R1
RF
Rg
Voltmeter
C
R2
S.S.G
Rg + R1 = R2 = Input and Output Impedance
C = 10pF (Including stray capacitance and input
capacitance of RF voltmeter.)
(1) : Input
(2) : Ground
(3) : Output
■ Frequency Characteristics
SFELF10M7KAB0-B0
SFELF10M7JAB0-B0
0
1
2
3
4
5
6
8.0
0
1
2
3
4
5
6
7.0
6.5
6.0
5.5
5.0
4.5
4.0
7.5
7.0
6.5
6.0
5.5
5.0
7
4.5
7
3.5
10.500
10.600
10.700
10.800
10.900
10.500
10.600
10.700
10.800
10.900
Frequency (MHz)
Frequency (MHz)
SFELF10M7HAB0-B0
SFELF10M7GAB0-B0
0
1
2
3
4
5
6
6.5
6.0
5.5
5.0
4.5
4.0
3.5
0
1
2
3
4
5
6
6.0
5.5
5.0
4.5
4.0
3.5
3.0
7
7
3.0
2.5
10.500
10.600
10.700
10.800
10.900
10.500
10.600
10.700
10.800
10.900
Frequency (MHz)
Frequency (MHz)
Continued on the following page.
25
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Continued from the preceding page.
■ Frequency Characteristics
SFELF10M7FAB0-B0
0
1
2
3
4
5
6
5.5
5.0
4.5
4.0
3.5
3.0
2.5
7
7
2.0
10.500
10.600
10.700
10.800
10.900
Frequency (MHz)
■ Frequency Characteristics (Spurious)
SFELF10M7KAB0-B0
SFELF10M7JAB0-B0
0
0
10
20
30
40
50
60
70
10
20
30
40
50
60
70
8.700
9.700
10.700
11.700
12.700
8.700
9.700
10.700
11.700
12.700
Frequency (MHz)
Frequency (MHz)
SFELF10M7HAB0-B0
SFELF10M7GAB0-B0
0
10
20
30
40
50
60
70
0
10
20
30
40
50
60
70
8.700
9.700
10.700
11.700
12.700
8.700
9.700
10.700
11.700
12.700
Frequency (MHz)
Frequency (MHz)
SFELF10M7FAB0-B0
0
10
20
30
40
50
60
70
8.700
9.700
10.700
11.700
12.700
Frequency (MHz)
26
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
CERAFILr 10.7MHz Wide Bandwidth Type
7.0±2.0
SFELF10M7 series for FM-receivers are monolithic type
ceramic filters which use the thickness expander mode
of the piezoelectric ceramic.
M A R K I N G
E I A J
C O D E
1.38±0.2
1.7±0.1
■ Features
Realizes widerband characteristics not obtained by
8
0.5±0.1
conventional ceramic filters.
2.5±0.2 2.5±0.2
(1) : Input
(2) : Ground
(3) : Output
SFELF10M7EA00-B0
(in mm)
(3)
(2)
(1)
7.0±2.0
M A R K I N G
E I A J
C O D E
1.38±0.2
1.7±0.1
0.5±0.1
2.5±0.2 2.5±0.2
(1) : Input
(2) : Ground
(3) : Output
SFELF10M7DF00-B0
(in mm)
(3)
(2)
(1)
Center
Nominal Center
Insertion
Loss
(dB)
Spurious
Attenuation
(dB)
Input/Output
Impedance
(ohm)
3dB Bandwidth
(kHz)
Attenuation
(kHz)
Part Number
Frequency (fo) Frequency (fn)
(MHz)
(MHz)
SFELF10M7EA00-B0
SFELF10M7DF00-B0
10.700 ±30kHz
-
330 ±50kHz
fn±175 min.
680 max.
950 max.
4.0 ±2.0dB
3.0 ±2.0dB
30 min.
20 min.
330
470
-
10.700
Area of Attenuation: [within 20dB]
Area of Spurious Attenuation: SFELF10M7EA00-B0: [within 8MHz to 12MHz], SFELF10M7DF00-B0: [within 5MHz to 15MHz]
Area of Insertion Loss: at minimum loss point
Center frequency (fo) defined by the center of 3dB bandwidth.
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
■ Standard Center Frequency Rank Code (SFELF10M7EA00-B0)
CODE
30kHz Step
25kHz Step
10.650MHz±25kHz
10.675MHz±25kHz
10.700MHz±25kHz
10.725MHz±25kHz
10.750MHz±25kHz
Combination A, B, C, D, E
Combination A, B, C
Color Code
D
B
A
C
E
Z
10.64MHz±30kHz
10.67MHz±30kHz
10.70MHz±30kHz
10.73MHz±30kHz
10.76MHz±30kHz
Black
Blue
Red
Orange
White
M
27
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Test Circuit
(1) (2) (3)
R1
RF
Voltmeter
Rg
C
R2
S.S.G
Rg + R1 = R2 = Input and Output Impedance
C = 10pF (Including stray capacitance and input
capacitance of RF voltmeter.)
(1) : Input
(2) : Ground
(3) : Output
8
■ Frequency Characteristics
SFELF10M7EA00-B0
SFELF10M7DF00-B0
0
1
2
3
4
5
6
4.5
0
1
2
3
4
5
6
4.5
4.0
3.5
3.0
2.5
2.0
1.5
4.0
3.5
3.0
2.5
2.0
1.5
7
7
1.0
1.0
10.300
10.500
10.700
10.900
11.100
10.300
10.500
10.700
10.900
11.100
Frequency (MHz)
Frequency (MHz)
■ Frequency Characteristics (Spurious)
SFELF10M7EA00-B0
SFELF10M7DF00-B0
0
0
10
20
30
40
50
60
10
20
30
40
50
60
70
70
8.700
9.700
10.700
11.700
12.700
8.700
9.700
10.700
11.700
12.700
Frequency (MHz)
Frequency (MHz)
28
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
CERAFILr 10.7MHz Narrow Bandwidth Type
7.0±2.0
■ Features
MARKING
SFELF10M7LFTA/KAH0, SFVLF/SFKLF series realizes
narrower band characteristics not obtained by
conventional ceramic filters. Besides, low spurious
EIAJ
CODE
1.65±0.1
and temperature characteristics is stable. This series
suits for European car-audio or AM up conversion use
that needs narrow band characteristics.
1.4±0.1
0.5±0.1
2.5±0.2 2.5±0.2
9
(1) : Input
SFVLF10M7MF00-B0
SFKLF10M7NL00-B0
SFELF10M7KAH0-B0
(2) : Ground
(3) : Output
(3)
(2)
(1)
(in mm)
10.0±2.0
7.0±2.0
M A R K I N G
MARKING
EIAJ
CODE
E I A J
C O D E
1.65±0.1
1.38±0.2
1.7±0.1
1.4±0.1
0.5±0.1
0.5±0.1
2.5±0.2 2.5±0.2
2.5±0.2 2.5±0.2
(1) : Input
(2) : Ground
(3) : Output
(1) : Input
(2) : Ground
(3) : Output
SFVLF10M7LF00-B0
(3)
(2)
(1)
(in mm)
(in mm)
(3)
(2)
(1)
7.0±2.0
7.0±2.0
M A R K I N G
M A R K I N G
E I A J
C O D E
E I A J
C O D E
1.38±0.2
1.38±0.2
1.7±0.1
1.7±0.1
0.5±0.1
0.5±0.1
2.5±0.2 2.5±0.2
2.5±0.2 2.5±0.2
(1) : Input
(2) : Ground
(3) : Output
(1) : Input
(2) : Ground
(3) : Output
SFELF10M7LFTA-B0
(in mm)
(in mm)
(3)
(2)
(1)
(3)
(2)
(1)
Center
Nominal Center
Insertion
Loss
(dB)
Spurious
Attenuation
(dB)
Input/Output
Impedance
(ohm)
3dB Bandwidth
Attenuation
(kHz)
Part Number
Frequency (fo) Frequency (fn)
(kHz)
(MHz)
(MHz)
SFVLF10M7MF00-B0
SFVLF10M7LF00-B0
SFKLF10M7NL00-B0
SFELF10M7LFTA-B0
SFELF10M7KAH0-B0
-
10.700
fn±13 min.
fn±25 min.
20 min.
135 max.
-
5.0 ±2.0dB
5.5 ±2.5dB
6.0 max.
35 min.
30 min.
24 min.
30 min.
30 min.
330
330
600
330
330
-
10.700
10.700 ±15kHz
-
-
95 max.
280 max.
350 max.
10.700
-
fn±25 min.
110 ±30kHz
7.0 ±2.0dB
7.0 ±2.0dB
10.700 ±30kHz
Area of Attenuation: [within 20dB]
Area of Spurious Attenuation: [within 9MHz to 12MHz], SFKLF10M7NL00-B0: [within fo-1.0MHz to fo+1.0MHz]
Area of Insertion Loss: at minimum loss point
Center frequency (fo) defined by the center of 3dB bandwidth.
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
29
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Standard Center Frequency Rank Code (SFELF10M7KAH0-B0)
CODE
30kHz Step
25kHz Step
10.650MHz±25kHz
10.675MHz±25kHz
10.700MHz±25kHz
10.725MHz±25kHz
10.750MHz±25kHz
Combination A, B, C, D, E
Combination A, B, C
Color Code
D
B
A
C
E
Z
10.64MHz±30kHz
10.67MHz±30kHz
10.70MHz±30kHz
10.73MHz±30kHz
10.76MHz±30kHz
Black
Blue
Red
Orange
White
M
■ Test Circuit
(1) (2) (3)
9
R1
RF
Rg
Voltmeter
C
R2
S.S.G
Rg + R1 = R2 = Input and Output Impedance
C = 10pF (Including stray capacitance and input
capacitance of RF voltmeter.)
(1) : Input
(2) : Ground
(3) : Output
■ Frequency Characteristics
SFVLF10M7MF00-B0
SFVLF10M7LF00-B0
0
1
2
3
4
5
6
19.0
0
1
2
3
4
5
6
15.0
14.0
13.0
12.0
11.0
10.0
9.0
18.0
17.0
16.0
15.0
14.0
13.0
12.0
7
7
8.0
10.600
10.650
10.700
10.750
10.800
10.600
10.650
10.700
10.750
10.800
Frequency (MHz)
Frequency (MHz)
SFKLF10M7NL00-B0
SFELF10M7LFTA-B0
0
1
2
3
4
5
6
0
1
2
3
4
5
6
12.0
11.0
10.0
9.0
8.0
7.0
6.0
7
7
5.0
10.600
10.650
10.700
10.750
10.800
10.600
10.650
10.700
10.750
10.800
Frequency (MHz)
Frequency (MHz)
Continued on the following page.
30
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Continued from the preceding page.
■ Frequency Characteristics
SFELF10M7KAH0-B0
0
1
2
3
4
5
6
8.0
7.5
7.0
6.5
6.0
5.5
5.0
7
4.5
10.600
10.650
10.700
10.750
10.800
Frequency (MHz)
9
■ Frequency Characteristics (Spurious)
SFVLF10M7MF00-B0
SFVLF10M7LF00-B0
0
0
10
20
30
40
50
60
10
20
30
40
50
60
70
70
8.700
9.700
10.700
11.700
12.700
8.700
9.700
10.700
11.700
12.700
Frequency (MHz)
Frequency (MHz)
SFKLF10M7NL00-B0
SFELF10M7LFTA-B0
0
10
20
30
0
10
20
30
40
50
60
40
50
60
70
70
8.700
11.700
11.200
9.700
10.200
10.700
9.700
10.700
11.700
12.700
Frequency (MHz)
Frequency (MHz)
SFELF10M7KAH0-B0
0
10
20
30
40
50
60
70
8.700
9.700
10.700
11.700
12.700
Frequency (MHz)
31
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
CERAFILr 10.7MHz for FM-IF Tuners
9.0 max.
SFELF10M7 series for FM-receivers are monolithic type
ceramic filters which use the thickness expander mode
of the piezoelectric ceramic.
MARKING
EIAJ
CODE
1.38±0.2
■ Features
1.7±0.1
1. Little dispersion of amplitude characteristics and
phase characteristics (G. D. T. characteristics)
2. The SFELF_X series has GDT characteristics and is
useful for obtaining low distortion. SFELF_L series,
in these ceramic filters, being in harmony with
flatness of GDT, roundness of the amplitude and
selectivity characteristics, therefore, these
ceramic filters are suitable to high-grade stereo
tuners. Even in mismatching conditions, they can
keep little distortion because of low Qm of ceramic
material. The SFELF_G series is based on
SFELF_FA00/GA00/HA00, and it obtains high selectivity
with low loss. There is little dispersion of
amplitude and GDT characteristics, and low
distortion rate can be obtained.
0.5±0.1
2.5±0.2 2.5±0.2
(1) : Input
(2) : Ground
(3) : Output
SFELF10M7JAXE-B0
SFELF10M7HAXD-B0
SFELF10M7GAXX-B0
SFELF10M7GALP03-B0
10
(3)
(2)
(1)
(in mm)
9.0 max.
MARKING
EIAJ
CODE
1.38±0.2
1.7±0.1
0.5±0.1
2.5±0.2 2.5±0.2
3. All products are inspected the flatness of GDT
characteristics.
(1) : Input
(2) : Ground
(3) : Output
(3)
(2)
(1)
(in mm)
7.0±2.0
9.0 max.
M A R K I N G
MARKING
EIAJ
CODE
E I A J
C O D E
1.38±0.2
1.7±0.1
1.38±0.2
1.7±0.1
0.5±0.1
0.5±0.1
2.5±0.2 2.5±0.2
2.5±0.2 2.5±0.2
(1) : Input
(1) : Input
(2) : Ground
(3) : Output
(2) : Ground
(3) : Output
SFELF10M7HA0G-B0
(in mm)
(3)
(2)
(1)
(in mm)
(3)
(2)
(1)
7.0±2.0
9.0 max.
M A R K I N G
MARKING
EIAJ
CODE
E I A J
C O D E
1.38±0.2
1.7±0.1
1.38±0.2
1.7±0.1
0.5±0.1
0.5±0.1
2.5±0.2 2.5±0.2
2.5±0.2 2.5±0.2
(1) : Input
(2) : Ground
(3) : Output
(1) : Input
(2) : Ground
(3) : Output
SFELF10M7GAXA-B0
(in mm)
(3)
(2)
(1)
(in mm)
(3)
(2)
(1)
Continued on the following page.
32
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Continued from the preceding page.
7.0±2.0
7.0±2.0
M A R K I N G
M A R K I N G
E I A J
C O D E
E I A J
C O D E
1.38±0.2
1.38±0.2
1.7±0.1
1.7±0.1
0.5±0.1
0.5±0.1
2.5±0.2 2.5±0.2
2.5±0.2 2.5±0.2
(1) : Input
(1) : Input
(2) : Ground
(3) : Output
(2) : Ground
(3) : Output
SFELF10M7GALM-B0
SFELF10M7GA0G-B0
(in mm)
(in mm)
(3)
(2)
(1)
(3)
(2)
(1)
7.0±2.0
7.0±2.0
M A R K I N G
M A R K I N G
10
E I A J
C O D E
E I A J
C O D E
1.38±0.2
1.7±0.1
1.38±0.2
1.7±0.1
0.5±0.1
0.5±0.1
2.5±0.2 2.5±0.2
2.5±0.2 2.5±0.2
(1) : Input
(1) : Input
(2) : Ground
(3) : Output
(2) : Ground
(3) : Output
SFELF10M7FALL-B0
SFELF10M7FA0G-B0
(in mm)
(in mm)
(3)
(2)
(1)
(3)
(2)
(1)
Center
Frequency (fo)
(MHz)
Insertion
Loss
(dB)
Spurious
Attenuation
(dB)
Input/Output
Impedance
(ohm)
3dB Bandwidth
Attenuation
GDT Bandwidth
(kHz)
Part Number
(kHz)
(kHz)
SFELF10M7JAXE-B0
SFELF10M7HAXD-B0
SFELF10M7HA0G-B0
SFELF10M7GAXX-B0
SFELF10M7GAXA-B0
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
150 ±30kHz
180 ±30kHz
180 ±40kHz
250 ±40kHz
220 ±40kHz
250 ±50kHz
230 ±50kHz
230 ±50kHz
280 ±50kHz
280 ±50kHz
500 max.
530 max.
520 max.
670 max.
610 max.
650 max.
600 max.
600 max.
700 max.
650 max.
14.0 max.
14.0 max.
7.0 max.
35 min. fo±50 min.[within 0.15µsec.]
33 min. fo±60 min.[within 0.15µsec.]
330
330
330
330
330
330
330
330
330
330
40 min.
fo±45 min.[within 0.5µsec.]
12.0 max.
12.5 max.
10.0 max.
9.0 ±2.0dB
7.0 max.
25 min. fo±110 min.[within 0.2µsec.]
30 min. fo±80 min.[within 0.15µsec.]
30 min. fo±65 min.[within 0.25µsec.]
30 min. fo±60 min.[within 0.25µsec.]
SFELF10M7GALP03-B0 10.700 ±30kHz
SFELF10M7GALM-B0
SFELF10M7GA0G-B0
SFELF10M7FALL-B0
SFELF10M7FA0G-B0
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
40 min.
25 min. fo±70 min.[within 0.25µsec.]
30 min. fo±85 min.[within 0.5µsec.]
fo±60 min.[within 0.5µsec.]
7.0 ±2.0dB
4.0 ±2.0dB
Area of Attenuation: [within 20dB]
Area of Spurious Attenuation: [within 9MHz to 12MHz], SFELF10M7GAXA-B0: [within 8MHz to 12MHz]
Area of Insertion Loss: at minimum loss point
Center frequency (fo) defined by the center of 3dB bandwidth.
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
■ Standard Center Frequency Rank Code
CODE
30kHz Step
25kHz Step
10.650MHz±25kHz
10.675MHz±25kHz
10.700MHz±25kHz
10.725MHz±25kHz
10.750MHz±25kHz
Combination A, B, C, D, E
Combination A, B, C
Color Code
Black
D
B
A
C
E
Z
10.64MHz±30kHz
10.67MHz±30kHz
10.70MHz±30kHz
10.73MHz±30kHz
10.76MHz±30kHz
Blue
Red
Orange
White
M
Continued on the following page.
33
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Continued from the preceding page.
■ Test Circuit
(1) (2) (3)
R1
RF
Voltmeter
Rg
C
R2
S.S.G
Rg + R1 = R2 = Input and Output Impedance
C = 10pF (Including stray capacitance and input
capacitance of RF voltmeter.)
(1) : Input
(2) : Ground
(3) : Output
■ Frequency Characteristics
10
SFELF10M7JAXE-B0
SFELF10M7HAXD-B0
0
1
2
3
4
5
6
5.00
0
1
2
3
4
5
6
4.50
4.25
4.00
3.75
3.50
3.25
3.00
2.75
4.75
4.50
4.25
4.00
3.75
3.50
3.25
7
7
10.400
10.500
10.500
10.500
10.600
10.700
Frequency (MHz)
10.800
10.900
10.900
10.900
11.000
10.400
10.500
10.500
10.500
10.600
10.700
Frequency (MHz)
10.800
10.900
10.900
10.900
11.000
SFELF10M7HA0G-B0
SFELF10M7GAXX-B0
0
1
2
3
4
5
6
6.5
6.0
5.5
5.0
4.5
4.0
3.5
0
1
2
3
4
5
6
3.25
3.00
2.75
2.50
2.25
2.00
1.75
1.50
7
3.0
11.000
7
10.400
10.600
10.700
Frequency (MHz)
10.800
10.400
10.600
10.700
Frequency (MHz)
10.800
11.000
SFELF10M7GAXA-B0
SFELF10M7GALP03-B0
0
1
2
3
4
5
6
3.75
0
1
2
3
4
5
6
3.75
3.50
3.25
3.00
2.75
2.50
2.25
2.00
3.50
3.25
3.00
2.75
2.50
2.25
2.00
7
7
10.400
10.600
10.700
10.800
11.000
10.400
10.600
10.700
10.800
11.000
Frequency (MHz)
Frequency (MHz)
Continued on the following page.
34
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Continued from the preceding page.
■ Frequency Characteristics
SFELF10M7GALM-B0
SFELF10M7GA0G-B0
0
1
2
3
4
5
6
4.00
3.75
3.50
3.25
3.00
2.75
2.50
2.25
0
1
2
3
4
5
6
6.0
5.5
5.0
4.5
4.0
3.5
3.0
7
7
2.5
10.400
10.500
10.600
10.700
10.800
10.900
11.000
10.400
10.500
10.600
10.700
10.800
10.900
11.000
Frequency (MHz)
Frequency (MHz)
10
SFELF10M7FALL-B0
SFELF10M7FA0G-B0
0
1
2
3
4
5
6
3.25
3.00
2.75
2.50
2.25
2.00
1.75
1.50
0
1
2
3
4
5
6
5.5
5.0
4.5
4.0
3.5
3.0
2.5
7
7
2.0
10.400
10.500
10.600
10.700
10.800
10.900
11.000
10.400
10.500
10.600
10.700
10.800
10.900
11.000
Frequency (MHz)
Frequency (MHz)
■ Frequency Characteristics (Spurious)
SFELF10M7JAXE-B0
SFELF10M7HAXD-B0
0
0
10
20
30
40
50
60
70
10
20
30
40
50
60
70
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
8.700
9.700
10.700
11.700
12.700
Frequency (MHz)
SFELF10M7HA0G-B0
SFELF10M7GAXX-B0
0
10
20
30
40
50
60
70
0
10
20
30
40
50
60
70
8.700
9.700
10.700
11.700
12.700
8.700
9.700
10.700
11.700
12.700
Frequency (MHz)
Frequency (MHz)
Continued on the following page.
35
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Continued from the preceding page.
■ Frequency Characteristics (Spurious)
SFELF10M7GAXA-B0
SFELF10M7GALP03-B0
0
10
20
30
40
50
60
0
10
20
30
40
50
60
70
70
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
12.700
12.700
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
10
SFELF10M7GALM-B0
SFELF10M7GA0G-B0
0
10
20
30
40
50
60
70
0
10
20
30
40
50
60
70
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
8.700
9.700
10.700
Frequency (MHz)
11.700
SFELF10M7FALL-B0
SFELF10M7FA0G-B0
0
10
20
30
40
50
60
0
10
20
30
40
50
60
70
8.700
70
9.700
10.700
11.700
12.700
8.700
9.700
10.700
11.700
Frequency (MHz)
Frequency (MHz)
36
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
CERAFILr 10.7MHz High Selectivity Type SFTLF Series
10.0±1.0
SFTLF10M7 series for FM-receivers are monolithic type
M A R K I N G
ceramic filters which use the thickness expander mode
of the piezoelectric ceramic.
E I A J
C O D E
0.4±0.1
■ Features
0.65±0.1
1.4±0.1
0.5±0.1
1. It has an excellent shape factor, and it is
possible to obtain 1.5 times more excellent
selectivity than SFELF10M7 series (by detuning
+-300 or 400kHz).
2.5±0.2 2.5±0.2
(1) : Input
(2) : Ground
(3) : Output
SFTLF10M7HA00-B0
SFTLF10M7GA00-B0
SFTLF10M7FA00-B0
2. Good performance of spurious suppression
3. Having the same terminal pitch as the SFELF10M7
series, it easily replaces that series.
(in mm)
(3)
(2)
(1)
11
10.0±1.0
4. By replacing two SFELF10M7 series filters with one
SFTLF10M7 filter, more compact sets can be made.
5. Well-suited for 1-chip ICs
M A R K I N G
E I A J
C O D E
0.4±0.1
0.65±0.1
1.4±0.1
0.5±0.1
2.5±0.2 2.5±0.2
(1) : Input
(2) : Ground
(3) : Output
(in mm)
(3)
(2)
(1)
10.0±1.0
M A R K I N G
E I A J
C O D E
0.4±0.1
0.65±0.1
1.4±0.1
0.5±0.1
2.5±0.2 2.5±0.2
(1) : Input
(2) : Ground
(3) : Output
(in mm)
(3)
(2)
(1)
Center
Frequency (fo)
(MHz)
Insertion
Loss
(dB)
Spurious
Attenuation
(dB)
Input/Output
Impedance
(ohm)
3dB Bandwidth
(kHz)
Attenuation
(kHz)
Part Number
SFTLF10M7HA00-B0
SFTLF10M7GA00-B0
SFTLF10M7FA00-B0
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
180 ±40kHz
230 ±40kHz
280 ±50kHz
510 max.
650 max.
700 max.
5.5 ±2.5dB
6.0 ±2.0dB
6.0 ±2.0dB
50 min.
50 min.
50 min.
330
330
330
Area of Attenuation: [within 40dB]
Area of Spurious Attenuation: [within 9MHz to 12MHz]
Area of Insertion Loss: at minimum loss point
Center frequency (fo) defined by the center of 3dB bandwidth.
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
37
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Standard Center Frequency Rank Code
CODE
30kHz Step
25kHz Step
10.650MHz±25kHz
10.675MHz±25kHz
10.700MHz±25kHz
10.725MHz±25kHz
10.750MHz±25kHz
Combination A, B, C, D, E
Combination A, B, C
Color Code
Black
D
B
A
C
E
Z
10.64MHz±30kHz
10.67MHz±30kHz
10.70MHz±30kHz
10.73MHz±30kHz
10.76MHz±30kHz
Blue
Red
Orange
White
M
■ Test Circuit
(1) (2) (3)
R1
RF
Rg
Voltmeter
C
R2
11
S.S.G
Rg + R1 = R2 = Input and Output Impedance
C = 10pF (Including stray capacitance and input
capacitance of RF voltmeter.)
(1) : Input
(2) : Ground
(3) : Output
■ Frequency Characteristics
SFTLF10M7HA00-B0
SFTLF10M7GA00-B0
0
1
2
3
4
5
6
8.5
0
1
2
3
4
5
6
7.5
7.0
6.5
6.0
5.5
5.0
4.5
8.0
7.5
7.0
6.5
6.0
5.5
7
7
5.0
4.0
10.500
10.600
10.700
10.800
10.900
10.500
10.600
10.700
10.800
10.900
Frequency (MHz)
Frequency (MHz)
SFTLF10M7FA00-B0
0
1
2
3
4
5
6
7.0
6.5
6.0
5.5
5.0
4.5
4.0
7
3.5
10.500
10.600
10.700
10.800
10.900
Frequency (MHz)
38
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Frequency Characteristics (Spurious)
SFTLF10M7HA00-B0
SFTLF10M7GA00-B0
0
0
10
20
30
40
50
60
10
20
30
40
50
60
70
70
8.700
9.700
10.700
11.700
12.700
8.700
9.700
10.700
11.700
12.700
Frequency (MHz)
Frequency (MHz)
SFTLF10M7FA00-B0
0
10
20
30
40
50
60
11
70
8.700
9.700
10.700
11.700
12.700
Frequency (MHz)
39
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr 10.7MHz Related Data on Lead Type
■ Temperature Characteristics
SFELF10M7GA00-B0
SFELF10M7HA00-B0
W40
W40
W20
0
Center frequency
Center frequency
W20
0
Y20
Y40
Y20
Y40
Y20
0
0
0
W20
W40
W40
W40
W60
W60
W60
W80
W80
W80
Y20
0
0
0
W20
W40
W40
W40
W60
W60
W60
W80
W80
W80
Temperature (˚C)
Temperature (˚C)
W2
W1
0
W2
W1
0
Insertion loss
Insertion loss
Y1
Y2
Y1
Y2
Y20
W20
Y20
W20
Temperature (˚C)
Temperature (˚C)
W40
W20
0
W40
W20
0
3dB Bandwidth
3dB Bandwidth
Y20
Y40
Y20
Y40
Y20
W20
Y20
W20
Temperature (˚C)
Temperature (˚C)
11
■ Matching Conditions
•When using ceramic filters, it is most important to
•The SFELF10M7 and SFTLF10M7 series are of
input/output symmetric structure so that in theory
there is no input/output directionality. Actual
circuits may use different input/output loading
conditions (for example, mismatched impedance) or
capacitance load. In such cases, the waveform will
be a little changed by the direction of the
match the input/output load to impedance 330 ohm
(SFELF10M7DF00-B0 is 470 ohm and
SFKLF10M7NL00-B0 is 600 ohm matching).
Waveform symmetry is damaged when reactance is added
to the input/output load.
•Two ceramic filters directly connected can be used
for high selectivity. For reducing waveform
variation, it is recommended to input a buffer AMP
between ceramic filters.
input/output of the ceramic filters.
■ Loaded Resistance and Waveform (Rg+R1=330 ohm)
SFELF10M7GA00-B0
R2=220Ω
R2=330Ω
0
1
2
3
4
5
6
7
1.2
1.0
0.8
0.6
0.4
0.2
0
0
1
2
3
4
5
6
7
1.2
1.0
0.8
0.6
0.4
0.2
0
10.5 10.6 10.7 10.8 10.9
Frequency (MHz)
10.5 10.6 10.7 10.8 10.9
Frequency (MHz)
R2=560Ω
R2=1kΩ
0
1
2
3
4
5
6
7
1.2
1.0
0.8
0.6
0.4
0.2
0
0
1
2
3
4
5
6
7
1.2
1.0
0.8
0.6
0.4
0.2
0
10.5 10.6 10.7 10.8 10.9
Frequency (MHz)
10.5 10.6 10.7 10.8 10.9
Frequency (MHz)
■ Loaded Capacitance and Waveform (Rg+R1=R2=330 ohm)
SFELF10M7HA00-B0
C=10pF
C=33pF
0
1
2
3
4
5
6
7
1.2
1.0
0.8
0.6
0.4
0.2
0
0
1
2
3
4
5
6
7
1.2
1.0
0.8
0.6
0.4
0.2
0
10.5 10.6 10.7 10.8 10.9
Frequency (MHz)
10.5 10.6 10.7 10.8 10.9
Frequency (MHz)
C=56pF
C=82pF
0
1
2
3
4
5
6
7
1.2
1.0
0.8
0.6
0.4
0.2
0
0
1
2
3
4
5
6
7
1.2
1.0
0.8
0.6
0.4
0.2
0
10.5 10.6 10.7 10.8 10.9
Frequency (MHz)
10.5 10.6 10.7 10.8 10.9
Frequency (MHz)
40
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
CERAFILr 4.5-6.5MHz Chip Type SFSKA Series
SMD ceramic filter SFSKA_CF is a small and thin SMD
filter sealed with a metal cap.
7.9±0.2
8.5±0.2
3.0±0.1
3.8±0.2
Recommended for LCD-TVs, and small and thin tuners.
1.8±0.2
0.5±0.1
■ Features
1. High attenuation outside bandwidth
0.6±0.2
1.0±0.1
2. Small and thin package
3. Reflow-solderable
1.3±0.2
0.3±0.1
(1) : Input
(2) : Ground
(3) : Output
1.3±0.2
(1)
(2)
(3)
(in mm)
2.5±0.2 2.5±0.2
12
Nominal Center
Frequency (fn)
(MHz)
3dB
Bandwidth
(kHz)
20dB
Bandwidth
(kHz)
Insertion
Loss
(dB)
Spurious
Attenuation(1)
(dB)
Spurious
Attenuation(2)
(dB)
Input/Output
Impedance
(ohm)
Part Number
20 min.
[within 0 to fn]
15 min.
[within fn to 7.0MHz]
SFSKA4M50CF00-R1
4.500
fn±60 min.
600 max.
6.0 max.
1000
Area of Insertion Loss: at minimum loss point
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
■ Standard Land Pattern Dimensions
■ Test Circuit
(1) (2) (3)
1.0
1.0
1.0
1.5
1.5
R1
Rg
RF
Voltmeter
E1
E2
R2
C2
S.S.G.
(1) : Input
(2) : Ground
(3) : Output
R1+Rg=R2=1000Ω ±5%, Rg=50Ω
C2=10pF (Including stray capacitance and Input capacitance of RF Voltmeter)
E1:S.S.G. Output voltage
(in mm)
■ Frequency Characteristics
■ Frequency Characteristics (Spurious)
0
10
20
30
40
50
60
70
0
10
20
30
40
50
60
70
0.0
2.0
4.0
6.0
8.0
10.0
3.5
3.7
3.9
4.1
4.3
4.5
4.7
4.9
5.1
5.3
5.5
Frequency (MHz)
Frequency (MHz)
41
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
CERAFILr 4.5-6.5MHz Standard Lead Type SFSRA Series
10.0 max.
As part of the environment protection activity, solder
for terminal plating and terminal-element connection
inside of ceramic filter SFSRA series contains no
lead (Pb).
M
7.0
(Ref.)
This series also features thickness shear mode same
as SFSRH series (current type), which provides very
low spurious response within video signal band.
2.5±0.2 2.5±0.2
(1) : Input
(2) : Ground
(3) : Output
■ Features
1. Excellent spurious suppression characteristics
(3)
(2)
(1)
(in mm)
within video signal band.
2. Available 4 pass bandwidth variation to meet
various requests.
3. Low profile (H=7.0mm max.)
4. Lead dimension: Improved mounting reliability
(cut & clinch) due to round terminal.
13
Nominal Center
Frequency (fn)
(MHz)
3dB
Bandwidth
(kHz)
20dB
Bandwidth
(kHz)
Insertion
Loss
(dB)
Spurious
Attenuation(1)
(dB)
Spurious
Attenuation(2)
(dB)
Input/Output
Impedance
(ohm)
Part Number
30 min.
[within 0 to fn]
20 min.
[within fn to 7.0MHz]
SFSRA4M50BF00-B0
SFSRA4M50CF00-B0
SFSRA4M50DF00-B0
SFSRA4M50EF00-B0
SFSRA5M50BF00-B0
SFSRA5M50CF00-B0
SFSRA5M50DF00-B0
SFSRA5M74BF00-B0
SFSRA5M74CF00-B0
SFSRA6M00BF00-B0
SFSRA6M00CF00-B0
SFSRA6M00DF00-B0
SFSRA6M50BF00-B0
SFSRA6M50CF00-B0
SFSRA6M50DF00-B0
4.500
4.500
4.500
4.500
5.500
5.500
5.500
5.742
5.742
6.000
6.000
6.000
6.500
6.500
6.500
fn±40 min.
fn±60 min.
fn±70 min.
fn±125 min.
fn±50 min.
fn±60 min.
fn±80 min.
fn±50 min.
fn±60 min.
fn±50 min.
fn±60 min.
fn±80 min.
fn±50 min.
fn±70 min.
fn±80 min.
420 max.
600 max.
750 max.
850 max.
400 max.
600 max.
750 max.
400 max.
600 max.
420 max.
600 max.
750 max.
470 max.
650 max.
800 max.
8.0 max.
6.0 max.
6.0 max.
6.0 max.
8.0 max.
6.0 max.
6.0 max.
8.0 max.
6.0 max.
8.0 max.
6.0 max.
6.0 max.
8.0 max.
6.0 max.
6.0 max.
1000
1000
1000
1000
600
600
600
600
600
600
470
470
470
470
470
30 min.
[within 0 to fn]
20 min.
[within fn to 7.0MHz]
30 min.
[within 0 to fn]
20 min.
[within fn to 7.0MHz]
25 min.
[within 0 to fn]
18 min.
[within fn to 7.0MHz]
30 min.
[within 0 to fn]
20 min.
[within fn to 7.5MHz]
30 min.
[within 0 to fn]
20 min.
[within fn to7.5MHz]
30 min.
[within 0 to fn]
20 min.
[within fn to 7.5MHz]
30 min.
[within 0 to fn]
20 min.
[within fn to 7.5MHz]
30 min.
[within 0 to fn]
20 min.
[within fn to 7.5MHz]
30 min.
[within 0 to fn]
20 min.
[within fn to 8.0MHz]
30 min.
[within 0 to fn]
20 min.
[within fn to 8.0MHz]
30 min.
[within 0 to fn]
20 min.
[within fn to 8.0MHz]
30 min.
[within 0 to fn]
20 min.
[within fn to 8.5MHz]
30 min.
[within 0 to fn]
20 min.
[within fn to 8.5MHz]
30 min.
[within 0 to fn]
20 min.
[within fn to 8.5MHz]
Area of Insertion Loss: at minimum loss point
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
42
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Test Circuit
1
2
3
R1
Rg
RF
Voltmeter
S.S.G.
R2
C
Rg+R1=R2=Input and Output Impedance
C=10pF (Including stray capacitance and
input capacitance of RF voltmeter)
(1) : Input
(2) : Ground
(3) : Output
■ Frequency Characteristics
SFSRA4M50BF00-B0
SFSRA4M50CF00-B0
0
10
20
30
40
50
60
70
0
10
20
30
40
50
60
70
13
3.5
3.7
3.9
4.1
4.3
4.5
4.7
4.9
5.1
5.3
5.5
3.5
3.7
3.9
4.1
4.3
4.5
4.7
4.9
5.1
5.3
5.5
Frequency (MHz)
Frequency (MHz)
SFSRA4M50DF00-B0
SFSRA4M50EF00-B0
0
0
10
20
30
40
50
60
70
10
20
30
40
50
60
70
3.5
3.7
3.9
4.1
4.3
4.5
4.7
4.9
5.1
5.3
5.5
3.5
3.7
3.9
54
4.3
4.5
4.7
4.9
5.1
5.3
5.5
Frequency (MHz)
Frequency (MHz)
SFSRA5M50BF00-B0
SFSRA5M50CF00-B0
0
0
10
20
30
40
50
60
70
10
20
30
40
50
60
70
4.5
4.7
4.9
5.1
5.3
5.5
5.7
5.9
6.1
6.3
6.5
4.5
4.7
4.9
5.1
5.3
5.5
5.7
5.9
6.1
6.3
6.5
Frequency (MHz)
Frequency (MHz)
Continued on the following page.
43
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Continued from the preceding page.
■ Frequency Characteristics
SFSRA5M50DF00-B0
SFSRA5M74BF00-B0
0
10
20
30
40
50
60
70
0
10
20
30
40
50
60
70
4.7
4.9
5.1
5.3
5.5
5.7
5.9
6.1
6.3
6.5
6.7
4.5
4.7
4.9
5.1
5.3
5.5
5.7
5.9
6.1
6.3
6.5
Frequency (MHz)
Frequency (MHz)
SFSRA5M74CF00-B0
SFSRA6M00BF00-B0
0
10
20
30
40
50
60
70
0
10
20
30
40
50
60
70
13
4.7
4.9
5.1
5.3
5.5
5.7
5.9
6.1
6.3
6.5
6.7
5.0
5.2
5.4
5.6
5.8
6.0
6.2
6.4
6.6
6.8
7.0
Frequency (MHz)
Frequency (MHz)
SFSRA6M00CF00-B0
SFSRA6M00DF00-B0
0
0
10
20
30
40
10
20
30
40
50
60
70
50
60
70
5.0
5.2
5.4
5.6
5.8
6.0
6.2
6.4
6.6
6.8
7.0
5.0
5.2
5.4
5.6
5.8
6.0
6.2
6.4
6.6
6.8
7.0
Frequency (MHz)
Frequency (MHz)
SFSRA6M50BF00-B0
SFSRA6M50CF00-B0
0
10
20
30
40
50
60
70
0
10
20
30
40
50
60
70
5.5
5.7
5.9
6.1
6.3
6.5
6.7
6.9
7.1
7.3
7.5
5.5
5.7
5.9
6.1
6.3
6.5
6.7
6.9
7.1
7.3
7.5
Frequency (MHz)
Frequency (MHz)
Continued on the following page.
44
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Continued from the preceding page.
■ Frequency Characteristics
SFSRA6M50DF00-B0
0
10
20
30
40
50
60
70
5.5
5.7
5.9
6.1
6.3
6.5
6.7
6.9
7.1
7.3
7.5
Frequency (MHz)
■ Frequency Characteristics (Spurious)
SFSRA4M50BF00-B0
SFSRA4M50CF00-B0
0
10
20
30
40
50
60
70
0
10
20
30
40
50
60
70
13
0.0
1.0
1.0
1.0
2.0
2.0
2.0
3.0
4.0
5.0
6.0
7.0
7.0
7.0
8.0
8.0
8.0
9.0
9.0
9.0
10.0
10.0
10.0
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
Frequency (MHz)
Frequency (MHz)
SFSRA4M50DF00-B0
SFSRA4M50EF00-B0
0
10
20
30
40
50
60
70
0
10
20
30
40
50
60
70
0.0
3.0
4.0
5.0
6.0
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
Frequency (MHz)
Frequency (MHz)
SFSRA5M50BF00-B0
SFSRA5M50CF00-B0
0
10
20
30
40
50
60
70
0
10
20
30
40
50
60
70
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
0.0
3.0
4.0
5.0
6.0
Frequency (MHz)
Frequency (MHz)
Continued on the following page.
45
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Continued from the preceding page.
■ Frequency Characteristics (Spurious)
SFSRA5M50DF00-B0
SFSRA5M74BF00-B0
0
10
20
30
40
50
60
70
0
10
20
30
40
50
60
70
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
Frequency (MHz)
Frequency (MHz)
SFSRA5M74CF00-B0
SFSRA6M00BF00-B0
0
0
10
20
30
40
50
60
70
10
20
30
40
50
60
70
13
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
Frequency (MHz)
Frequency (MHz)
SFSRA6M00CF00-B0
SFSRA6M00DF00-B0
0
10
20
30
40
50
60
70
0
10
20
30
40
50
60
70
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
Frequency (MHz)
Frequency (MHz)
SFSRA6M50BF00-B0
SFSRA6M50CF00-B0
0
10
20
30
40
50
60
70
0
10
20
30
40
50
60
70
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
Frequency (MHz)
Frequency (MHz)
Continued on the following page.
46
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Continued from the preceding page.
■ Frequency Characteristics (Spurious)
SFSRA6M50DF00-B0
0
10
20
30
40
50
60
70
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
Frequency (MHz)
13
47
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
CERAFILr 3.5-6.5MHz for Chroma Signal SFSRA/F Series
10.0 max.
Chroma signals frequency conversion process is
involved in VCRs video signal processing circuit.
These SFSRA/SFSRF series are suitable for B.P.F.
M
7.0
(Ref.)
■ Features
1. Frequency adjustment free
2. Responsible for VHS. 8mm VCR system
2.5±0.2 2.5±0.2
(1) : Input
SFSRA Series
(2) : Ground
(3) : Output
(3)
(2)
(1)
(in mm)
Nominal Center
Frequency (fn)
(MHz)
3dB
Bandwidth
(kHz)
20dB
Bandwidth
(kHz)
Insertion
Loss
(dB)
Spurious
Attenuation(1)
(dB)
Spurious
Attenuation(2)
(dB)
Input/Output
Impedance
(ohm)
Part Number
30 min.
[within 0 to fn]
20 min.
[within fn to 7.0MHz]
SFSRA4M43CF00-B0
SFSRF3M58CF00-B0
4.430
3.580
fn±60 min.
fn±40 min.
600 max.
530 max.
6.0 max.
6.0 max.
1000
1000
14
25 min.
[within 0 to fn]
15 min.
[within fn to 6.0MHz]
Area of Insertion Loss: at minimum loss point
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
■ Test Circuit
1
2
3
R1
Rg
RF
Voltmeter
S.S.G.
R2
C
Rg+R1=R2=Input and Output Impedance
C=10pF (Including stray capacitance and
input capacitance of RF voltmeter)
(1) : Input
(2) : Ground
(3) : Output
■ Frequency Characteristics
■ Frequency Characteristics (Spurious)
SFSRA4M43CF00-B0
SFSRA4M43CF00-B0
0
10
20
0
10
20
30
40
50
30
40
50
60
60
70
70
3.5
3.7
3.9
4.1
4.3
4.5
4.7
4.9
5.1
5.3
5.5
0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0
Frequency (MHz)
Frequency (MHz)
48
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
CERAFILr 455kHz Chip Type PFWCC Series
Input Mark
IN
GND
PFWCC series for AM use is one of the most
recommendable intermediate filters, having such
distinctive features as high selectivity, high
stability, and adjustment-free operation.
OUT
GND
5.7±0.3
Additionally its easy matching with IC helps create an
easy circuit design.
1.2±0.2
1.2±0.2
(2)
(3)
This is the most recommendable for portable radio with
small package. Especially, reflowable with SMD package.
(1)
(4)
■ Features
4.0±0.2
(in mm)
1. Center frequency range between 450 and 470kHz
are available standard tolerance of +-2kHz.
2. For frequency synthesizers, center frequencies
of 450, 459 and 468kHz are available standard
tolerance of +-1kHz.
Center
Frequency (fo)
(kHz)
3dB
Bandwidth
(kHz)
Input/Output
Impedance
(ohm)
Selectivity (+)
(dB)
Selectivity (-)
(dB)
Insertion Loss
(dB)
Part Number
Element
15
PFWCC450KS2A-R0
450 ±2.0kHz
5.5 ±1.5kHz
17 min.[fo+9kHz]
17 min.[fo-9kHz]
6.0 max.
3000
2
Area of Insertion Loss: at minimum loss point
Center frequency (fo) is defined by the center of 3dB bandwidth.
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
■ Standard Land Pattern Dimensions
6.0
4.0
1.2
1.2
(in mm)
The solder resist should be printed except for the land
pattern on the P.C.B.
The material of P.C.B. is the epoxy resin of glass fabric
base (t=0.8mm)
49
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Recommended IFT
PFWCC/PFSLF
Type
Item
7×7mm IFT
5×5mm IFT
(1)—(2)
85T
(2)—(3)
(4)—(6)
23T
(1)—(2)
84T
(2)—(3)
(4)—(6)
33T
Winding Specification
S(3)
(4)S
(6)
(2)
(1)
67T
98T
(Bottom view)
No load Qu
90
65
Tuning Capacitance
180pF
180pF
• Maching of CERAFILr PF_ series with IFT is decided by the IFT secondary side
impedance, |Z2|. Set the |Z2| at about 4.2kΩ.
■ Test Circuit (CERAFILr Only)
■ Test Circuit (CERAFILr with IFT)
7pF
3kΩ
(1)
(2)
(3)
(1)
(4)
(2)
(3)
IFT
(4)
(4)
300kΩ
(3)
(2)
S.S.G.
(Rg=50Ω)
RF
Voltmeter
RF
Voltmeter
S.S.G.
(Rg=50Ω)
(1)
(6)
15
■ Frequency Characteristics
■ Frequency Characteristics (Spurious)
IFT+PFWCC450KS2A-R0
IFT+PFWCC450KS2A-R0
0
0
10
20
10
20
30
40
50
30
40
50
60
70
60
70
0.000
1.000
2.000
3.000
4.000
430
440
450
460
470
Frequency (kHz)
Frequency (kHz)
50
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
CERAFILr 455kHz Chip Type SFPKA Series
7.0±0.3
3.0±0.3
SFPKA series for AM use is one of the most
recommendable intermediate filters, having such
distinctive features as high selectivity, high
stability and adjustment-free operation.
MARKING
EIAJ
CODE
0.9±0.1
Additionally its easy matching with IC helps create an
easy circuit design.
1.5±0.3
2.0±0.3
1.5±0.3
1.6±0.3
2.0±0.3
■ Features
Connection
(1) : Input
(2) : Ground
(3) : Output
(1) (2) (3)
1. The filters are mountable by automatic placers
and can be reflow soldered and withstand
washing.
(in mm)
2. The filters are wide bandwidth and high
selectivity. So they are suitable for car radio
and multi band radio.
Center
Frequency (fo)
(kHz)
6dB
Bandwidth
(kHz)
Input/Output
Impedance
(ohm)
Selectivity (+)
(dB)
Selectivity (-)
(dB)
Insertion Loss
(dB)
Part Number
Element
SFPKA450KH1A-R1
SFPKA450KG1A-R1
SFPKA450KF4A-R1
450 ±1.0kHz
450 ±1.0kHz
450 ±1.5kHz
fn±3.0 min.
fn±4.5 min.
fn±6.0 min.
40 min.[fn+9kHz]
40 min.[fn+10kHz]
40 min.[fn-9kHz]
40 min.[fn-10kHz]
6.0 max.
6.0 max.
6.0 max.
2000
1500
1500
4
4
4
16
40 min.[fn+12.5kHz] 40 min.[fn-12.5kHz]
Area of Insertion Loss: at minimum loss point
Center frequency (fo) is defined by the center of 6dB bandwidth.
(fn) means nominal center frequency (450kHz).
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
■ Standard Land Pattern Dimensions
6.95
2.475
2.0
1.1
2.0
0.925
2.0
(in mm)
51
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Recommended IFT
■ Test Circuit
Type
SFPKA
Item
(1)—(2)
60T
(2)—(3)
(4)—(6)
28T
Winding Specification
R1
(3)
(1)
S(3)
(2)
(4)S
(6)
(2)
125T
(1)
RF Voltmeter
Rg
E1
R2
E2
(Bottom view)
No load Qu
S.S.G.
0dBm
40
Tuning Capacitance
180pF
• Matching of CERAFILr SFPKA series with IFT is decided by the Qu of IFT
and IFT secondary side impedance, |Z2|. Set the Qu at about 40 because
a Qu value which is too high (e.g.,90) may produce ripple in the waveform.
It is recommended to match the impedance of |Z2| with that of the
CERAFILr.
(1) : Input
(2) : Ground
(3) : Output
Rg+R1=R2=Input/Output Impedance
E1 : S.S.G. Output Voltage
■ Frequency Characteristics
SFPKA450KH1A-R1
SFPKA450KG1A-R1
0
400
360
0
400
10
20
30
40
360
320
280
240
200
160
120
80
10
320
280
240
200
160
120
80
20
30
40
50
60
50
60
16
70
70
80
90
80
90
40
40
0
100
100
0
425
450
475
425
450
475
Frequency (kHz)
Frequency (kHz)
SFPKA450KF4A-R1
0
400
10
20
30
40
360
320
280
240
50
60
200
160
70
120
80
90
80
40
100
0
425
450
475
Frequency (kHz)
52
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
CERAFILr 455kHz SFULA/SFZLA Series
7.0±0.3
SFULA/SFZLA series for AM use is one of the most
recommendable intermediate filters, having such
distinctive features as high selectivity, high
stability, and adjustment-free operation.
Additionally its easy matching with IC helps create
an easy circuit design.
MARKING
EIAJ
CODE
0.25
0.1
1.1±0.1
0.8±0.1
■ Features
Connection
(1) : Input
(2) : Ground
(3) : Output
1. Center frequency range between 450 to 470kHz
are available standard tolerance of +-2kHz.
2. For frequency synthesizers, center frequencies
of 450, 459 and 468kHz are available standard
tolerance of +-1kHz.
SFULA Series
(3) (2)
(1)
2.5±0.22.5±0.2
(in mm)
7.0±0.3
MARKING
EIAJ
CODE
0.25
0.1
1.1±0.1
0.8±0.1
17
(1)
(6)
(2)
(5)
(3)
(4)
Connection
(1) : Input
(2)(5) : Ground
(3)(4) : Direct connection
(6) : Output
SFZLA Series
2.5±0.2 2.5±0.2
(in mm)
Center
Frequency (fo)
(kHz)
3dB
Bandwidth
(kHz)
Input/Output
Impedance
(ohm)
Selectivity (+)
(dB)
Selectivity (-)
(dB)
Insertion Loss
(dB)
Part Number
Element
SFULA455KU2A-B0
SFULA455KU2B-B0
SFZLA455KN2A-B0
SFZLA455KS2A-B0
SFZLA455KT2A-B0
455 ±2.0kHz
462 ±2.0kHz
455.5 ±2.0kHz
456 ±2.0kHz
456 ±2.0kHz
10.0 ±3.0kHz
10.0 ±3.0kHz
4.0 ±1.0kHz
5.5 ±1.0kHz
7.0 ±1.0kHz
4 min.[fo+10kHz]
4 min.[fo+10kHz]
23 min.[fo+9kHz]
18 min.[fo+9kHz]
16 min.[fo+9kHz]
6 min.[fo-10kHz]
6 min.[fo-10kHz]
23 min.[fo-9kHz]
18 min.[fo-9kHz]
16 min.[fo-9kHz]
5.0 max.
5.0 max.
7.0 max.
7.0 max.
6.0 max.
3000
3000
3000
3000
3000
1
1
2
2
2
Area of Insertion Loss: at minimum loss point
Center frequency (fo) is defined by the center of 3dB bandwidth.
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
■ Frequency Characteristics (CERAFILr with IFT)
Selectivity
6dB Band Width
(kHz)
Input Level (at 0.6mV output)
(dB)
Part Number
+9kHz off (dB)
-9kHz off (dB)
6.5
5.0
7.0
8.5
20
23
78
IFT+SFULA455KU2B-B0
IFT+SFZLA455KN2A-B0
IFT+SFZLA455KS2A-B0
IFT+SFZLA455KT2A-B0
38
33
27
78
78
78
Typ. value
53
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Recommended IFT
SFULApB
SFZLApA
Type
Item
7×7mm IFT
(1)—(2)
70T
(2)—(3)
(4)—(6)
(1)—(2)
(2)—(3)
(4)—(6)
14T
Winding Specification
S(3)
(4)S
(6)
(2)
(1)
115T
7T
68T
84T
(Bottom view)
No load Qu
105
90
Tuning Capacitance
180pF
180pF
• Maching of CERAFILr SFULA/SFZLA series with IFT is decided by the IFT secondary side
impedance, |Z2|. The design target values of |Z2| are :
For SFULApB : 300Ω
For SFZLApA : 1kΩ
■ Test Circuit (CERAFILr Only)
SFULA Series
SFZLA Series
(3)
(2)
(4)
(5)
3kΩ
(1)
(3)
3kΩ
(2)
(1)
(6)
RF
S.S.G.
Voltmeter
(Rg=50Ω)
RF
S.S.G.
Voltmeter
(Rg=50Ω)
17
■ Test Circuit (CERAFILr with IFT)
SFULA Series
SFZLA Series
7pF
(3)
(2)
(4)
(5)
7pF
(1)
(4)
(3)
IFT
IFT
(1)
(4)
(6)
300kΩ
(2)
300kΩ
(3)
(2)
(3)
(2)
RF
Voltmeter
S.S.G.
(Rg=50Ω)
RF
Voltmeter
S.S.G.
(Rg=50Ω)
(1)
(6)
(1)
(6)
54
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Frequency Characteristics
IFT+SFULA455KU2B-B0
IFT+SFZLA455KN2A-B0
0
10
20
30
40
50
60
70
0
10
20
30
40
50
60
70
435
445
455
465
475
435
445
455
465
475
Frequency (kHz)
Frequency (kHz)
IFT+SFZLA455KS2A-B0
IFT+SFZLA455KT2A-B0
0
10
20
30
40
50
60
70
0
10
20
30
40
50
60
70
435
445
455
465
475
435
445
455
465
475
17
Frequency (kHz)
Frequency (kHz)
■ Frequency Characteristics (Spurious)
IFT+SFULA455KU2B-B0
IFT+SFZLA Series
0
0
10
20
30
40
50
10
20
30
40
50
60
70
80
60
70
80
0
1
2
3
4
5
6
7
8
9
10
0
1
2
3
4
5
6
7
8
9
10
Frequency (MHz)
Frequency (MHz)
55
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
CERAFILr 455kHz PFSLF/PFWLF Series
6.0±1.0
PFSLF/PFWLF series for AM use is one of the most
recommendable intermediate filters, having such
distinctive features as high selectivity, high
stability, and adjustment-free operation.
1.4±0.1
Additionally its easy matching with IC helps create
an easy circuit design.
1.4±0.1
0.5±0.1
This is the most recommendable for portable radios
with small package.
Marking :
2.5±0.2 2.5±0.2
(1) Input
(2) Ground
(3) Output
: EIAJ Monthly Code
PFSLF Series
■ Features
(in mm)
(3)
(2)
(1)
1. Center frequency range between 450 to 470kHz
are available standard tolerance of +-2kHz.
2. For frequency synthesizers, center frequencies
of 450, 459 and 468kHz are available standard
tolerance of +-1kHz.
6.0±1.0
1.4±0.1
1.4±0.1
0.5±0.1
Marking :
(1) Input
(2) Ground
(3) Output
2.5±0.2 2.5±0.2
: Vender's Code
: EIAJ monthly Code
PFWLF Series
18
(3)
(2)
(1)
(in mm)
Center
Frequency (fo)
(kHz)
3dB
Bandwidth
(kHz)
Input/Output
Impedance
(ohm)
Selectivity (+)
(dB)
Selectivity (-)
(dB)
Insertion Loss
(dB)
Part Number
Element
PFSLF455KP2A-B0
PFWLF450KP2A-B0
PFWLF450KS2A-B0
455 ±2.0kHz
450 ±2.0kHz
450 ±2.0kHz
4.5 ±1.5kHz
4.5 ±1.5kHz
5.5 ±1.5kHz
8 min.[fo+9kHz]
19 min.[fo+9kHz]
17 min.[fo+9kHz]
8 min.[fo-9kHz]
19 min.[fo-9kHz]
17 min.[fo-9kHz]
5.0 max.
7.0 max.
6.0 max.
3000
3000
3000
1
2
2
Area of Insertion Loss: at minimum loss point
Center frequency (fo) is defined by the center of 3dB bandwidth.
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
56
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Recommended IFT
PFSLF455KP2A-B0
PFWCC/PFSLF
Type
Item
7×7mm IFT
5×5mm IFT
(1)—(2)
85T
(2)—(3)
(4)—(6)
23T
(1)—(2)
84T
(2)—(3)
(4)—(6)
33T
Winding Specification
S(3)
(4)S
(6)
(2)
(1)
67T
98T
(Bottom view)
No load Qu
90
65
Tuning Capacitance
180pF
180pF
• Maching of CERAFILr PF_ series with IFT is decided by the IFT secondary side
impedance, |Z2|. Set the |Z2| at about 4.2kΩ.
■ Test Circuit (CERAFILr Only)
■ Test Circuit (CERAFILr with IFT)
PFSLF/PFWLF Series
PFSLF/PFWLF Series
7pF
3kΩ
(1)
(3)
(1)
(3)
IFT
300kΩ
(2)
(4)
(2)
(3)
(2)
RF
S.S.G.
S.S.G.
RF
Voltmeter
(Rg=50Ω)
(Rg=50Ω)
Voltmeter
(1)
(6)
18
■ Frequency Characteristics
IFT+PFSLF455KP2A-B0
IFT+PFWLF450KS2A-B0
0
0
10
20
30
40
50
10
20
30
40
50
60
70
60
70
435
445
455
465
475
430
440
450
460
470
Frequency (kHz)
Frequency (kHz)
■ Frequency Characteristics (Spurious)
IFT+PFSLF455KP2A-B0
IFT+PFWLF450KS2A-B0
0
0
10
20
30
40
50
10
20
30
40
50
60
70
60
70
0.000
1.000
2.000
3.000
4.000
0.000
1.000
2.000
3.000
4.000
Frequency (kHz)
Frequency (kHz)
57
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
CERAFILr 455kHz SFPLA/CFWLA Series
8.0±0.3
MARKING
SFPLA/CFWLA series for AM use is one of the most
recommendable intermediate filters, having such
distinctive features as high selectivity, high
stability, high attenuation, and adjustment-free
operation. Additionally its easy matching with IC
helps create an easy circuit design.
EIAJ
CODE
0.8±0.1
0.6±0.1
0.15±0.05
This is the most recommendable for car-stereo and
all band radio with high attenuation.
2.7
±
0.3
1.2±0.5
Connection
(1) : Input
(2) : Ground
(3) : Output
(2) (1)
(3)
SFPLA Series
(in mm)
3.3±0.5
11.0±0.5
MARKING
EIAJ
CODE
0.8±0.1
0.6±0.1
0.15
2.9±0.3
2.6±0.3
1.2±0.5
22..99—±00.3.3
Connection
(1) : Input
(2)(3)(4) : Ground
(5) : Output
(4)
(3)
(2) (1)
CFWLA Series
(5)
(in mm)
2.3±0.5
2.0±0.3
19
Center
Frequency (fo)
(kHz)
6dB
Bandwidth
(kHz)
Input/Output
Impedance
(ohm)
Selectivity (+)
(dB)
Selectivity (-)
(dB)
Insertion Loss
(dB)
Part Number
Element
SFPLA450KJ1A-B0
SFPLA450KH1A-B0
CFWLA450KJFA-B0
CFWLA450KHFA-B0
450 ±1.0kHz
450 ±1.0kHz
450 (fn)
fn±2.0 min.
fn±3.0 min.
fn±2.0 min.
fn±3.0 min.
40 min.[fn+7.5kHz]
40 min.[fn+9kHz]
50 min.[fn+7.5kHz]
50 min.[fn+9kHz]
40 min.[fn-7.5kHz]
40 min.[fn-9kHz]
50 min.[fn-7.5kHz]
50 min.[fn-9kHz]
6.0 max.
6.0 max.
7.0 max.
6.0 max.
2000
2000
2000
2000
4
4
6
6
450 (fn)
Area of Insertion Loss: at minimum loss point
Center frequency (fo) is defined by the center of 6dB bandwidth.
(fn) means nominal center frequency (450kHz).
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
■ Recommended IFT
■ Test Circuit
SFPLA/CFULA/CFWLA
Type
Item
7×7mm IFT
Input
Output
R1
(1)—(2)
60T
(2)—(3)
(4)—(6)
28T
Winding Specification
S(3)
(2)
(4)S
(6)
Rg
125T
(1)
RF
R2
SSG
Voltmeter
(Bottom view)
No load Qu
40
Ground
Tuning Capacitance
180pF
• Matching of CERAFILr SFPLA/CFULA/CFWLA series with IFT is decided
by the Qu of IFT and IFT secondary side impedance, |Z2|. Set the Qu at
about 40 because a Qu value which is too high (e.g.,90) may produce
ripple in the waveform. It is recommended to match the impedance of |Z2|
with that of the CERAFILr.
Rg+R1 =R2 : Input/Output Impedance
Continued on the following page.
58
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Continued from the preceding page.
■ Frequency Characteristics
IFT+SFPLA450KH1A-B0
IFT+CFWLA450KHFA-B0
0
0
10
20
30
40
50
60
70
10
20
30
40
50
60
70
430
440
450
460
470
430
440
450
460
470
Frequency (kHz)
Frequency (kHz)
■ Frequency Characteristics (Spurious)
IFT+SFPLA450KH1A-B0
IFT+CFWLA450KHFA-B0
0
0
10
20
30
40
50
10
20
30
40
50
60
70
80
60
70
80
0
1
2
3
4
5
6
7
8
9
10
0
1
2
3
4
5
6
7
8
9
10
Frequency (kHz)
Frequency (kHz)
19
59
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
CERAFILr 455kHz for AM Stereo Wide Bandwidth Type SFPLA/CFWLA/CFULA Series
8.0±0.3
MARKING
SFPLA/CFULA/CFWLA series for AM use is one of the most
EIAJ
CODE
recommendable intermediate filters, having such
distinctive features as high selectivity, high
stability, high attenuation, and adjustment-free
0.8±0.1
operation. Additionally its easy matching with IC
helps create an easy circuit design.
0.15±0.05
0.6±0.1
Especially, CFULA/CFWLA_Y series is the frequency
fidelity in the high sound area of an AM stereo will
be improved with wide band, flat group delay time
characteristics.
2.7
±
0.3
1.2±0.5
Connection
(1) : Input
(2) : Ground
(3) : Output
(2) (1)
(3)
SFPLA Series
(in mm)
3.3±0.5
11.0±0.5
8.0±0.3
MARKING
MARKING
EIAJ
CODE
EIAJ
CODE
0.8±0.1
0.8±0.1
0.15
0.15±0.05
2.7±0.3
0.6±0.1
2.9±0.3
2.6±0.3
1.2±0.5
0.6±0.1
1.2±0.5
22..99—±00.3.3
Connection
(2) (1)
(3)
Connection
(1) : Input
(2) : Ground
(3) : Output
(1) : Input
(2)(3)(4) : Ground
(5) : Output
(4)
(3)
(2) (1)
CFWLA Series
Part Number
CFULA Series
(5)
(in mm)
3.3±0.5
(in mm)
2.3±0.5
2.0±0.3
Center
Frequency (fo) Bandwidth
(kHz) (kHz)
6dB
GDT 20µsec. Input/Output
Bandwidth
(kHz)
20
Selectivity (+)
(dB)
Selectivity (-)
Insertion Loss
(dB)
Impedance Element
(ohm)
(dB)
SFPLA450KG1A-B0 450 ±1.0kHz fn±4.5 min.
30 min.[fn+9kHz]
30 min.[fn-9kHz]
6.0 max.
6.0 max.
6.0 max.
4.0 max.
10.0 max.
9.0 max.
7.0 max.
11.0 max.
10.0 max.
8.0 max.
6.0 max.
6.0 max.
6.0 max.
4.0 max.
-
2000
4
4
4
4
4
4
4
6
6
6
6
6
6
6
SFPLA450KF1A-B0 450 ±1.0kHz fn±6.0 min. 40 min.[fn+12.5kHz] 40 min.[fn-12.5kHz]
SFPLA450KE1A-B0 450 ±1.0kHz fn±7.5 min. 40 min.[fn+15kHz] 40 min.[fn-15kHz]
SFPLA450KD1A-B0 450 ±1.0kHz fn±10.0 min. 40 min.[fn+20kHz] 40 min.[fn-20kHz]
CFULA450KG1Y-B0 450 ±1.0kHz fn±4.5 min. 40 min.[fn+15kHz] 40 min.[fn-15kHz]
CFULA450KF1Y-B0 450 ±1.0kHz fn±6.0 min. 40 min.[fn+17.5kHz] 40 min.[fn-17.5kHz]
CFULA450KD1Y-B0 450 ±1.0kHz fn±10.0 min. 40 min.[fn+25kHz] 40 min.[fn-25kHz]
CFWLA450KG1Y-B0 450 ±1.0kHz fn±4.5 min. 50 min.[fn+15kHz] 50 min.[fn-15kHz]
CFWLA450KF1Y-B0 450 ±1.0kHz fn±6.0 min. 50 min.[fn+17.5kHz] 50 min.[fn-17.5kHz]
CFWLA450KD1Y-B0 450 ±1.0kHz fn±10.0 min. 50 min.[fn+25kHz] 50 min.[fn-25kHz]
-
2000
1500
1500
2000
2000
1500
2000
2000
1500
2000
2000
1500
1500
-
-
fn±3.0
fn±4.0
fn±7.0
fn±4.0
fn±5.0
fn±8.0
-
CFWLA450KGFA-B0
CFWLA450KFFA-B0
CFWLA450KEFA-B0
CFWLA450KDFA-B0
450 (fn)
450 (fn)
450 (fn)
450 (fn)
fn±4.5 min. 50 min.[fn+10kHz] 50 min.[fn-10kHz]
fn±6.0 min. 50 min.[fn+12.5kHz] 50 min.[fn-12.5kHz]
fn±7.5 min. 50 min.[fn+15kHz] 50 min.[fn-15kHz]
fn±10.0 min. 50 min.[fn+20kHz] 50 min.[fn-20kHz]
-
-
-
Area of Insertion Loss: at minimum loss point
Center frequency (fo) is defined by the center of 6dB bandwidth.
(fn) means nominal center frequency (450kHz).
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
60
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Recommended IFT
■ Test Circuit
SFPLA/CFULA/CFWLA
Type
Item
7×7mm IFT
Input
Output
R1
(1)—(2)
60T
(2)—(3)
(4)—(6)
28T
Winding Specification
S(3)
(2)
(4)S
(6)
Rg
125T
(1)
RF
Voltmeter
R2
SSG
(Bottom view)
No load Qu
40
Ground
Tuning Capacitance
180pF
• Matching of CERAFILr SFPLA/CFULA/CFWLA series with IFT is decided
by the Qu of IFT and IFT secondary side impedance, |Z2|. Set the Qu at
about 40 because a Qu value which is too high (e.g.,90) may produce
ripple in the waveform. It is recommended to match the impedance of |Z2|
with that of the CERAFILr.
Rg+R1 =R2 : Input/Output Impedance
■ Frequency Characteristics
IFT+SFPLA450KF1A-B0
IFT+CFWLA450KFFA-B0
0
10
20
30
40
50
60
70
0
10
20
30
40
50
60
70
430
440
450
460
470
430
450
460
470
440
Frequency (kHz)
Frequency (kHz)
IFT+CFULA450KF1Y-B0
IFT+CFWLA450KF1Y-B0
0
0
20
10
20
30
10
20
30
200
100
0
200
100
0
40
50
60
70
40
50
60
70
430
450
460
470
440
430
450
460
470
440
Frequency (kHz)
Frequency (kHz)
61
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
CERAFILr 455kHz for AM Search-stop Signal Detection
BFULA series are narrow bandwidth filters. This filter
is used in the application which detects the carrier
peak with a narrow bandwidth amplifier, or an
electronic tuner as a stop signal detector.
7.0±0.3
MARKING
EIAJ
CODE
■ Features
Most suitable for IC Station Detectors (SD)
0.8±0.1
1.1±0.1
5.0±0.2
(in mm)
No directivity
Resonant Frequency (Fr)
(kHz)
Delta F (Fa-Fr)
(kHz)
Resonant Resistance
(ohm)
Capacitance
(pF)
Part Number
BFULA450KC-B0
450 ±1.0kHz
450 ±0.8kHz
450 ±1.0kHz
14.0 ±2.0kHz
9.0 ±2.0kHz
27.5 ±4.5kHz
20 max.
30 max.
30 max.
360 ±20%
360 ±20%
550 ±20%
BFULA450KC004-B0
BFULA450KK003-B0
fa-fr: Difference between the anti-resonant frequency and the resonant frequency.
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page."
■ Impedance Characteristics
BFULA450KC004-B0
500k
100k
50k
21
10k
5k
1k
500
100
50
10
5
1
445
450
455
460
Frequency (kHz)
62
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr 455kHz SF/PF Series Temperature Characteristics
■ SFZLA455KS2A-B0
■ SFPLA450KH1A-B0
+1
+1
0
Temperature (D)
Temperature (D)
60
40
40
40
60
20
20
20
80
40
40
40
-
20
0
0
20
20
20
80
0
-20
-20
-20
0
0
0
-1
-
1
+1
0
+1
0
60
60
80
80
-
-
20
20
80
80
Temperature (D)
Temperature (D)
-1
-
1
+1
0
+1
0
Temperature (D)
Temperature (D)
60
60
0
-1
-
1
■ PFWLF450KS2A-B0
+1
0
60
40
40
20
80
-
20
0
0
Temperature (D)
-
1
+1
0
60
80
80
20
20
-
20
20
Temperature (D)
-
1
+1
0
-
60
0
40
Temperature (D)
-
1
21
63
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr 455kHz SF/PF/BF Series Application Circuit
■ Car Radio
SFPLA450KH1A-B0/BFULA450KC004-B0
PFSLF455KP2A-B0/PFWLF450KS2A-B0
BFULA450KC004-B0
Ant
Input
Station Det Out
CF2
Vco(+8v)
+
120
2.7k
10k
100k
430P
4.7µH
Vtune
AF Out
PFSLF455KP2A-B0
0.01
14
10k
100p
µ
+
0.47µ
15
2
4
6
8
10
12
16
18
20
19
18
3
17
16
14
13
8
12
9
11
10
µPC1216V2 (NEC)
LA1135(SANYO)
1
2
4
5
6
7
1
3
5
7
9
11
13
15
17
19
+
1µ
Det.
ANT
0.01µ
Output
CF1
0.047µ
x2
100µH
PFWLF450KS2A-B0
100
Vcc
(+13V)
Unit
R : Ω
C : F
L : H
CF1: PFWLF450KS1A-B0
SFZLA450KS1A-B0
Unit
SFPLA450KH1A-B0
R : Ω
C : F
L : H
■ Portable Radio
SFULA455KU2B-B0
FM PF
FM OSC
FM CERAFIL
®
(SFELF10M7FA00-B0)
+
FM/AM
R
BAND SELECT
+
IF
OUT
FM IF
IN
9
7
6
14 17
2
19
25
26
Vcc
15
FM DISCRI
METER
REG
OUT
FM IF
AMP
FM
8
TUNING
METER
RIPPLE
FILTER
FM
REGULATOR
12
13
10
FRONT
END
+
BPF
DETECTOR
28
1
AM ANT
CXA1019M (SONY)
VOL
AM
FRONT
END
AM IF
AF
AMP
PRE/POWER
AMP
SP
27
+
DETECTOR
AGC
AMP
AM IF
IN
20 16
AF IN
11
5
18
22
23
21
4
24
3
DEP
OUT
+
AM OSC
+
+
21
+
®
AM CERAFIL
(SFULA455KU2B-B0)
Unit
VOL
R : Ω
C : F
L : H
Continued on the following page.
64
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr 455kHz SF/PF/BF Series Application Circuit
Continued from the preceding page.
■ Portable Radio
SFULA455KU2B-B0
IS2236
0.022µ
100k
CSBLA456
KE2ZF16-B0
FM
+
ST
L3
L1
L2
T1
4.7µ
-
AM
10µ
+
L
MO
+
+
-
-
15p
FM
OSC
+
-
-
FM
PF
R
AM
OSC
DEF
OUT
OUT Vcc1
LPF1 LPF2
VCO
MPX
IN
OUT
L
OUT
R
AM
PF IN
4.7µ
24
23
22
21
20
19
AF
18
17
16
15
14
ST
13
PRE
Phase
COM
Phase
COM
FM
AM
TA8122AN (TOSHIBA)
VCO
Freq
DECODER
OSC OSC
AM
MIX
AM/FM
MONO SW
AM
RF
AM
DET
HYS
SW
Divider
AM
MIX
AM
AGC
AM
IF
L
FM
DET
TUN
LED
ST
LED
FM
RF
FM
IF
DET
1
2
3
4
5
6
7
8
9
10
TUN
LED
11
12
FM
RF IN
FM
MIX
AM
MIX
AM
AGC
AM
IF IN
FM
IF IN
GND1
Vcc2
ST
LED
GND2
QUAD
+
BPF
0.033µ
-
T2
Vcc
(3V)
10µ
+
Unit
SFULA455 SFELF10
KU2B-B0 M7FA00-B0
CDALF10
M7GA16-B0
R : Ω
C : F
L : H
-
■ In Tr Circuit
BFULA450KK003-B0
+6V
0.01µ
0.01µ
21
3k
S.S.G.
(10mV)
RF
Volt meter
BFULA
450KK003-B0
Unit
R : Ω
C : F
L : H
65
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
Ceramic Trap 4.5-6.5MHz Chip Type TPSKA Series
SMD ceramic trap TPSKA_B is small and thin SMD trap
sealed with a metal cap. Recommended for LCD-TVs, and
small and thin tuners.
7.9±0.2
8.5±0.2
3.0±0.1
3.8±0.2
1.8±0.2
0.5±0.1
■ Features
1. High attenuation and high performance group
0.6±0.2
1.0±0.1
delay time
1.3±0.2
0.3±0.1
2. Small and thin package
3. Reflow-solderable
(1) : Input
(2) : Ground
(3) : Output
1.3±0.2
(1)
(2)
(3)
(in mm)
2.5±0.2 2.5±0.2
Nominal Center
Frequency (fn1)
(MHz)
Attenuation
(at fn1)
(dB)
30dB Attenuation
BW (fn1)
Part Number
(kHz)
TPSKA4M50B00-R1
4.500
35 min.
50 min.
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
■ Standard Land Pattern Dimensions
■ Test Circuit
L
1.0
1.0
1.0
R1
1.5
1.5
Rg
50Ω
R2
RF
Voltmeter
S.S.G.
22
Rg=50Ω
L=15µH
R1=330Ω
R2=1.0kΩ
(in mm)
■ Frequency Characteristics
■ Frequency Characteristics (Spurious)
0
10
20
30
40
50
60
70
0
10
20
30
40
50
60
70
80
700
600
500
400
300
200
100
0
0
1.0
2.0
3.0
4.0
5.0
4.0
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
5.0
Frequency (MHz)
Frequency (MHz)
66
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
Ceramic Trap 4.5-6.5MHz Chip Type Double Traps TPWKA Series
SMD ceramic trap TPWKA is small and thin SMD trap
M
sealed with a metal cap. Recommended for LCD-TVs, and
small and thin tuners.
7.9±0.2
4.2±0.1
This series consist of 2 wafers with 2 trap
frequencies. Recommended for Multi standard set.
8.5±0.2
5.0±0.2
0.4±0.2
1.0±0.1
■ Features
(1) : Input or Output
(2) : Ground
(3) : Output or Input
0.3±0.1
1. Good performance of attenuation
2. Small and thin package
3. Reflow-solderable
(1)
(2)
(3)
2.5±0.2 2.5±0.2
(in mm)
Nominal Center
Frequency (fn1)
(MHz)
Nominal Center
Frequency (fn2)
(MHz)
Attenuation
(at fn1)
(dB)
Attenuation
(at fn2)
(dB)
30dB Attenuation
BW (fn1)
Part Number
(kHz)
TPWKA5M50B04-R1
5.500
5.742
30 min.
30 min.
50 min.
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
■ Standard Land Pattern Dimensions
■ Test Circuit
1.2
1.2
1.2
L
1.3
1.3
R1
Rg
R2
C2
50Ω
RF
Voltmeter
S.S.G.
L = 8.2 µH
Rg = 50 Ω
R1 = 150 Ω
R2 = 330 Ω
23
C2 = 10pF (Including stray capacitance and input capacitance of RF voltmeter)
(in mm)
■ Frequency Characteristics
■ Frequency Characteristics (Spurious)
0
0
10
20
30
40
50
60
10
20
30
40
50
60
70
800
600
400
200
0
70
0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
4.5
4.7
4.9
5.1
5.3
5.5
5.7
5.9
6.1
6.3
6.5
Frequency (MHz)
Frequency (MHz)
67
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
Ceramic Trap 4.5-6.5MHz Standard Lead Type TPSRA Series
10.0 max.
As part of the environment protection activity, solder
M
for terminal plating and terminal-element connection
inside of ceramic filter TPSRA series contain no
lead (Pb).
7.0
(Ref.)
This series consist of two trap element on one wafer.
Suitable for the sound IF trap of CTV/VCR.
2.5±0.2 2.5±0.2
■ Features
(1) : Input
(2) : Ground
(3) : Output
1. Good performance of attenuation
2. Shape factor can be changed by the value of
Inductor "L".
(3)
(2)
(1)
(in mm)
3. Three-terminals type.
4. Low profile (H=7.0mm max.)
5. Lead dimension:
Improved mounting reliability (cut & clinch) due to
round terminal.
Nominal Center
Frequency (fn1)
(MHz)
Attenuation
(at fn1)
(dB)
30dB Attenuation
BW (fn1)
Part Number
(kHz)
TPSRA4M50B00-B0
TPSRA4M50C00-B0
TPSRA5M50B00-B0
TPSRA5M74B00-B0
TPSRA6M00B00-B0
TPSRA6M50B00-B0
4.500
4.500
5.500
5.742
6.000
6.500
35 min.
30 min.
35 min.
35 min.
35 min.
35 min.
50 min.
-
70 min.
70 min.
70 min.
70 min.
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
■ Test Circuit
TPSRA4M50B00-B0
TPSRA4M50C00-B0
24
15µH
8.2µH
330ohm
220ohm
Rg=50ohm
S.S.G.
Rg=50ohm
S.S.G.
R.F.
Voltmeter
R.F.
Voltmeter
Continued on the following page.
68
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Continued from the preceding page.
■ Test Circuit
TPSRA5M50/5M74/6M00/6M50B00-B0
15µH
220ohm
Rg=50ohm
S.S.G.
R.F.
Voltmeter
■ Frequency Characteristics
TPSRA4M50B00-B0
TPSRA4M50C00-B0
0
10
20
30
40
50
60
0
10
20
30
40
50
60
70
70
4.0
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
5.0
4.0
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
5.0
Frequency (MHz)
Frequency (MHz)
TPSRA5M50B00-B0
TPSRA5M74B00-B0
0
0
10
20
30
40
50
10
20
30
40
50
24
60
70
60
70
5.0
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
6.0
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
6.0
6.1
6.2
Frequency (MHz)
Frequency (MHz)
TPSRA6M00B00-B0
TPSRA6M50B00-B0
0
10
20
30
40
50
0
10
20
30
40
50
60
70
60
70
5.5
5.6
5.7
5.8
5.9
6.0
6.1
6.2
6.3
6.4
6.5
6.0
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
7.0
Frequency (MHz)
Frequency (MHz)
Continued on the following page.
69
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Continued from the preceding page.
■ Frequency Characteristics (Spurious)
TPSRA4M50B00-B0
TPSRA4M50C00-B0
0
10
20
30
40
50
60
0
10
20
30
40
50
60
800
600
400
200
0
800
600
400
200
0
70
70
0
0
0
1.0
1.0
1.0
2.0
2.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
8.0
8.0
9.0
9.0
9.0
10.0
0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
Frequency (MHz)
Frequency (MHz)
TPSRA5M50B00-B0
TPSRA5M74B00-B0
0
10
20
30
40
50
60
0
10
20
30
40
50
60
800
600
400
200
0
800
600
400
200
0
70
70
0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
3.0
4.0
5.0
6.0
7.0
10.0
Frequency (MHz)
Frequency (MHz)
TPSRA6M00B00-B0
TPSRA6M50B00-B0
0
10
20
30
40
50
60
0
10
20
30
40
50
60
800
600
400
200
0
800
600
400
200
0
24
70
70
0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
3.0
4.0
5.0
6.0
7.0
10.0
Frequency (MHz)
Frequency (MHz)
70
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
Ceramic Trap 3.5-6.5MHz Two Lead Type TPSRF_J Series
10.0 max.
Ceramic Trap TPSRF_J series are two-terminals type.
Which are recommended for the attenuation of sound IF
in B/W TV and the attenuation of chroma signal in
Video Camcorder.
T
J
E I A J
C O D E
1.38±0.2
0.5±0.1
■ Features
1. Small-size, lightweight
2. High performance, durability
3. Easy to design due to two-terminals type
5.0±0.2
in mm
Nominal Center
Frequency (fn1)
(MHz)
Attenuation
(at fn1)
(dB)
30dB Attenuation
BW (fn1)
Part Number
(kHz)
TPSRF3M58J00-B0
TPSRF4M43J00-B0
TPSRF4M50J00-B0
TPSRF5M50J00-B0
TPSRF5M74J00-B0
TPSRF6M00J00-B0
TPSRF6M50J00-B0
3.580
4.430
4.500
5.500
5.742
6.000
6.500
20 min.
20 min.
20 min.
20 min.
20 min.
20 min.
20 min.
20 min.[20dB Att.BW]
40 min.[20dB Att.BW]
30 min.[20dB Att.BW]
30 min.[20dB Att.BW]
30 min.[20dB Att.BW]
40 min.[20dB Att.BW]
40 min.[20dB Att.BW]
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
■ Test Circuit
75Ω
Rg=50Ω
R.F.
Voltmeter
Ceramic
Trap
25
S.S.G.
71
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Frequency Characteristics
TPSRF3M58J00-B0
TPSRF4M43J00-B0
0
10
20
30
40
50
0
10
20
30
40
50
60
70
60
70
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
4.0
4.1
3.9
4.0
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
Frequency (MHz)
Frequency (MHz)
TPSRF4M50J00-B0
TPSRF5M50J00-B0
0
10
20
30
40
50
0
10
20
30
40
50
60
70
60
70
4.0
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
5.0
5.0
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
6.0
Frequency (MHz)
Frequency (MHz)
TPSRF5M74J00-B0
TPSRF6M00J00-B0
0
10
20
30
40
50
0
10
20
30
40
50
60
70
60
70
25
5.5
5.6
5.7
5.8
5.9
6.0
6.1
6.2
6.3
6.4
6.5
4.74 4.94 5.14 5.34 5.54 5.74 5.94 6.14 6.34 6.54 6.74
Frequency (MHz)
Frequency (MHz)
TPSRF6M50J00-B0
0
10
20
30
40
50
60
70
6.0
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
7.0
Frequency (MHz)
72
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Frequency Characteristics (Spurious)
TPSRF3M58J00-B0
TPSRF4M43J00-B0
0
10
20
30
40
50
0
10
20
30
40
50
60
70
60
70
0.0
1.0
1.0
1.0
1.0
2.0
2.0
2.0
2.0
3.0
4.0
5.0
6.0
7.0
7.0
7.0
7.0
8.0
8.0
8.0
8.0
9.0
9.0
9.0
9.0
10.0
10.0
10.0
10.0
0.0
1.0
1.0
1.0
2.0
2.0
2.0
3.0
4.0
5.0
6.0
7.0
7.0
7.0
8.0
8.0
8.0
9.0
9.0
9.0
10.0
10.0
10.0
Frequency (MHz)
Frequency (MHz)
TPSRF4M50J00-B0
TPSRF5M50J00-B0
0
0
10
20
30
40
50
10
20
30
40
50
60
70
60
70
0.0
3.0
4.0
5.0
6.0
0.0
3.0
4.0
5.0
6.0
Frequency (MHz)
Frequency (MHz)
TPSRF5M74J00-B0
TPSRF6M00J00-B0
0
10
20
30
40
50
0
10
20
30
40
50
60
70
60
70
25
0
3.0
4.0
5.0
6.0
0.0
3.0
4.0
5.0
6.0
Frequency (MHz)
Frequency (MHz)
TPSRF6M50J00-B0
0
10
20
30
40
50
60
70
0.0
3.0
4.0
5.0
6.0
Frequency (MHz)
73
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
Ceramic Trap 3.5-6.5MHz for 2ch Sound TV in Germany TPSRF_W Series
7.0±2.0
Ceramic trap TPSRF_W series has same structure as
T
TPSRF_B series. But they can trap two individual
E
I
A
D
J
frequencies at one time. Recommended for two channel
multi-sound TV systems.
C
O
E
1.38±0.2
1.7±0.1
■ Features
0.5±0.1
1. Space saving
2.5
±0.2 ±0.2
2.5
2. Three-terminals type
(1) : Input
(2) : Ground
(3) : Output
(in mm)
(3)
(2)
(1)
Nominal Center
Frequency (fn1)
(MHz)
Nominal Center
Frequency (fn2)
(MHz)
Attenuation
(at fn1)
(dB)
Attenuation
(at fn2)
(dB)
30dB Attenuation
BW (fn1)
Part Number
(kHz)
TPSRF5M50W00-B0
5.500
5.742
32 min.
25 min.
70 min.
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
■ Test Circuit
15µH
330ohm
Rg=50ohm
R.F.
Voltmeter
S.S.G.
■ Frequency Characteristics
■ Frequency Characteristics (Spurious)
26
0
10
20
30
40
50
0
10
20
30
40
50
60
70
60
70
5.0
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
6.0
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
Frequency (MHz)
Frequency (MHz)
74
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
Ceramic Trap 3.5-6.5MHz Double Traps TPWRF Series
7.0±2.0
Ceramic trap TPWRF_B series consist of two wafers with
two trap frequencies. Recommended for Dual standard
sets.
T
W
B
E I A J
C O D E
1.38±0.2
1.7±0.1
■ Features
1. Good performance of attenuation
0.5±0.1
2. Small and thin package
3. Three-terminals type
2.5±
0.2 2.5
±0.2
(1) : Input
(2) : Ground
(3) : Output
(in mm)
(3)
(2)
(1)
Nominal Center
Frequency (fn1)
(MHz)
Nominal Center
Frequency (fn2)
(MHz)
Attenuation
(at fn1)
(dB)
Attenuation
(at fn2)
(dB)
30dB Attenuation
Part Number
BW (fn1)
(kHz)
TPWRF4M50B05-B0
TPWRF4M50B06-B0
TPWRF4M50B10-B0
TPWRF4M50B11-B0
TPWRF5M50B02-B0
TPWRF5M50B03-B0
TPWRF5M50B04-B0
TPWRF5M50B07-B0
TPWRF6M00B01-B0
4.500
4.500
4.500
4.500
5.500
5.500
5.500
5.500
6.000
6.000
4.850
4.724
5.500
6.500
6.000
5.742
5.850
6.500
30 min.
30 min.
30 min.
30 min.
30 min.
30 min.
30 min.
30 min.
30 min.
30 min.
30 min.
30 min.
30 min.
30 min.
30 min.
30 min.
30 min.
30 min.
50 min.
50 min.
50 min.
50 min.
50 min.
50 min.
50 min.
50 min.
70 min.
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
■ Test Circuit
8.2µH
150ohm
Rg=50ohm
R.F.
Voltmeter
S.S.G.
27
75
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Frequency Characteristics
TPWRF5M50B02-B0
TPWRF5M50B03-B0
0
10
20
30
40
50
0
10
20
30
40
50
60
70
60
70
4.5
4.7
4.9
5.1
5.3
5.5
5.7
5.9
6.1
6.3
6.5
5.0
5.2
5.4
5.6
5.8
6.0
6.2
6.4
6.6
6.8
7.0
Frequency (MHz)
Frequency (MHz)
TPWRF5M50B04-B0
TPWRF6M00B01-B0
0
10
20
30
40
50
0
10
20
30
40
50
60
70
60
70
4.5
4.7
4.9
5.1
5.3
5.5
5.7
5.9
6.1
6.3
6.5
5.0
5.2
1.0
1.0
5.4
2.0
2.0
5.6
5.8
6.0
6.2
6.4
7.0
7.0
6.6
8.0
8.0
6.8
9.0
9.0
7.0
Frequency (MHz)
Frequency (MHz)
■ Frequency Characteristics (Spurious)
TPWRF5M50B02-B0
TPWRF5M50B03-B0
0
0
10
20
30
40
50
10
20
30
40
50
60
70
60
70
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
0.0
3.0
4.0
5.0
6.0
10.0
Frequency (MHz)
Frequency (MHz)
27
TPWRF5M50B04-B0
TPWRF6M00B01-B0
0
0
10
20
30
40
50
10
20
30
40
50
60
70
60
70
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
0.0
3.0
4.0
5.0
6.0
10.0
Frequency (MHz)
Frequency (MHz)
76
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
Ceramic Trap 3.5-6.5MHz Triple Traps TPTRF Series
8.0±2.0
Ceramic trap TPTRF_B series consist of 3 wafers with
3 trap frequencies. Recommended for Multi standard
sets.
T
T
B
E I A J
C O D E
1.38±0.2
1.7±0.1
■ Features
1. Good performance of attenuation
2. Space saving for Multi set
3. Three-terminals type
0.5±0.1
2.5±0.2
2.5±0.2
(1) : Input
(2) : Ground
(3) : Output
(in mm)
(3)
(2)
(1)
Nominal Center
Frequency (fn1)
(MHz)
Nominal Center
Frequency (fn2)
(MHz)
Nominal Center
Frequency (fn3)
(MHz)
Attenuation
(at fn1)
(dB)
Attenuation
(at fn2)
(dB)
Attenuation
(at fn3)
(dB)
30dB Attenuation
BW (fn1)
Part Number
(kHz)
TPTRF5M50B01-B0
TPTRF5M50B02-B0
TPTRF5M50B04-B0
5.500
5.500
5.500
6.000
5.742
5.742
6.500
6.500
6.000
30 min.
30 min.
30 min.
30 min.
30 min.
30 min.
30 min.
30 min.
30 min.
50 min.
50 min.
50 min.
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
■ Test Circuit
8.2µH
150ohm
Rg=50ohm
R.F.
Voltmeter
S.S.G.
■ Frequency Characteristics
■ Frequency Characteristics (Spurious)
TPTRF5M50B01-B0
TPTRF5M50B01-B0
28
0
0
10
10
20
30
40
50
60
70
80
20
30
40
50
60
70
80
90
5.000
90
5.500
6.000
6.500
7.000
0.0
2.5
5.0
7.5
10.0
Frequency (MHz)
Frequency (MHz)
77
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
Ceramic Discriminator 10.7MHz Ultra Thin Chip Type CDSCB Series
4.5±0.1
CDSCB10M7 series forms a resonator on a piezoelectric
ceramic substrate. In combination with ICs, this type
obtains stable demodulation characteristics in a wide
0.2±0.2
0.4±0.05
bandwidth.
4.1 max.
They have 1.0mm max. thickness and small mounting area
(4.5x2.0mm).
0.4(ref.)
0.8±0.1
0.4(ref.)
0.8±0.1
■ Features
1. Compact and high reliability and recommended for
automotive applications.
1.5±0.1 1.5±0.1
(in mm)
2. Can be combined with various ICs. The IC is
determined by the last number in the part number.
3. Stable demodulation characteristics can be
obtained without adjustment.
4. Stable temperature characteristics
5. Recommended for Pb free soldering
Recovered Audio
Recovered Audio
Output
Center Frequency (fo)
(MHz)
Distortion
(% )
Part Number
3dB BW
(kHz)
IC
(mV)
CDSCB10M7GA105A-R0
CDSCB10M7GA113-R0
CDSCB10M7GA119-R0
CDSCB10M7GA121-R0
CDSCB10M7GF072-R0
CDSCB10M7GF109-R0
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
10.700 (fn)
220 min.
300 min.
110 min.
110 min.
75 min.
1.5 max.
1.0 max.
1.0 max.
1.0 max.
2.0 max.
3.0 max.
TEA5757HL
TA2154FN
TRF6901
500 min.
390 min.
80 min.
LV23100V
TA31161
fn±150 min.
fn±100 min.
130 min.
170 min.
10.700 (fn)
TK14588V
(fn) means nominal center frequency (10.700MHz).
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
■ Standard Center Frequency Rank Code
CODE
30kHz Step
25kHz Step
D
B
A
C
E
Z
10.64MHz±30kHz
10.67MHz±30kHz
10.70MHz±30kHz
10.73MHz±30kHz
10.76MHz±30kHz
10.650MHz±25kHz
10.675MHz±25kHz
10.700MHz±25kHz
10.725MHz±25kHz
10.750MHz±25kHz
Combination A, B, C, D, E
Combination A, B, C
M
29
■ Standard Land Pattern Dimensions
3.0
1.0
2.0
1.0
(in mm)
78
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Test Circuit
CDSCB10M7GA105A-R0
CDSCB10M7GA113-R0
Vcc (1.2V)
Vcc (3.0V)
0.1µ
10µ
+
48 47 46 45 44 43 42 41 40 39 38 37
0.1µ
1
2
36
35
34
33
32
31
30
29
28
27
26
25
+
100µ
30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
TA2154FN (TOSHIBA)
S.S.G.
3
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
4
+
5
X
2.2µ
6
TEA5757HL
(PHILIPS)
7
D.C. OUT
AF OUT
8
9
100k
X : CDSCB10M7GA113-R0
S.S.G.
10
11
12
Unit C : F
R : Ω
10
DC OUT
330p
13 14 15 16 17 18 19 20 21 22 23 24
+
4.7µ
X
0.22µ
X : CDSCB10M7GA105A-R0
150
Unit C : F
AF OUT
R : Ω
CDSCB10M7GA119-R0
CDSCB10M7GA121-R0
Vcc (3.0V)
0.01µ
AF Output
D.C. Output
Vcc (3.2V)
IF Input
AF Output
220k
68p
0.01µ
0.01µ
0.015µ
15p
10
22µ+
120p
82p
36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19
LV23100V (SANYO)
4.7µ
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18
48 47 46 45 44 43 42 41 40 39 38 37
0.01µ
1
36
35
34
X
10k
0.01µ
2
3
4
5
6
7
8
9
+
10µ
0.047µ
1000p
+
33
32
31
30
29
28
27
26
25
47p
TRF6901
(TEXAS INSTRUMENTS)
+
0.47µ
0.01µ
100p 10
11
12
3.3k
13 14 15 16 17 18 19 20 21 22 23 24
+
0.1µ
0.01µ
1µ
0.22µ
+
0.47µ
+
S.G.
10k
100p
10k
18 17 16 15 14 13 12 11 10
PIC16F84 (Control IC)
18 17 16 15 14 13 12 11 10
PIC16F84
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
X : CDSCB10M7GA119-R0
1k
2.2µ
1k
10k
Unit C : F
R : Ω
10k
+
+
Unit C : F
0.1µ
2.2µ
0.1µ
X : CDSCB10M7GA121-R0
L : H
R : Ω
CDSCB10M7GF072-R0
CDSCB10M7GF109-R0
Vcc (3V)
0.01µ
Vcc (3V)
4.7µ
R
X
R
X
0.01µ
0.01µ
AF OUT
D.C. OUT
AF OUT
10p
29
0.01µ
1000p
51k
8p
12k
16 15 14 13 12 11 10
TA31161 (TOSHIBA)
9
8
1
2
3
4
5
6
7
16 15 14 13 12 11 10
TK14588V (TOKO)
9
8
0.01µ
X : CDSCB10M7GF072-R0
+
R : 820
Unit C : F
R : Ω
33µ
0.01µ
1
2
3
4
5
6
7
IF IN
L : H
+
S.S.G.
X : CDSCB10M7GF109-R0
R : 820
Unit C : F
R : Ω
L : H
79
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Frequency Characteristics
CDSCB10M7GA105A-R0
CDSCB10M7GA113-R0
1000
100
10
100
10
1
1000
100
10
100
10
1
AF Output
Distortion
AF Output
Distortion
1
0.1
1
0.1
Input = 100 dBµ
fdev. = ±75kHz
fmod. = 1kHz
Vcc = 3.0V
Input = 100 dBµ
fdev. = ±75kHz
fmod. = 1kHz
Vcc = 1.2V
10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1
Frequency (MHz)
10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1
Frequency (MHz)
CDSCB10M7GA119-R0
CDSCB10M7GA121-R0
1000
100
10
1
1000
100
10
1
AF Output
AF Output
100
10
1
100
10
1
Distortion
Distortion
0.1
0.1
Input = 100 dBµ
fdev. = ±60kHz
fmod. = 1kHz
Vcc = 3.0V
Input = 100 dBµ
fdev. = ±75kHz
fmod. = 1kHz
Vcc = 3.2V
10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1
Frequency (MHz)
10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1
Frequency (MHz)
CDSCB10M7GF072-R0
CDSCB10M7GF109-R0
1000
100
1000
100
10
1
100
10
100
10
1
29
10
1
1
0.1
0.1
Input = 100dBµ
fdev. = ±80kHz
fmod. = 1kHz
Vcc = 3.0V
Input = 100dBµ
fdev. = ±64kHz
fmod. = 1kHz
Vcc = 3.0V
10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1
Frequency (MHz)
10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1
Frequency (MHz)
80
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
Ceramic Discriminator 10.7MHz Standard Lead Type CDALF Series
8.0±1.0
Freq. Rank (Color Dot)
CDALF10M7 series forms a resonator on a piezoelectric
ceramic substrate. In combination with ICs, this type
obtains stable demodulation characteristics in wide
bandwidths.
E
C
I
A
J
M
A
R
K
I
N
G
O
D
E
0.4±0.1
0.5±0.1
0.65±0.1
5.0±0.2
■ Features
1. Compact and excellent mechanical strength
2. Can be combined with various ICs. The IC is
determined by the last number in the part number.
3. Stable demodulation characteristics can be obtained
without adjustment.
CDALF10M7G_ Series
(in mm)
4. Stable temperature characteristics
5. We recommend combination: ceramic discriminator
CDALF10M7 series and "CERAFIL" SFELF10M7 Series
of the same frequency rank.
8.0±1.0
Freq. Rank (Color Dot)
E
C
I
A
J
M
A
R
K
I
N
G
O
D
E
0.4±0.1
0.5±0.1
0.65±0.1
5.0±0.2
CDALF10M7C_ Series
(in mm)
Recovered Audio
Recovered Audio
Center Frequency (fo)
(MHz)
Distortion
(% )
Part Number
3dB BW
(kHz)
Output
(mV)
IC
CDALF10M7GA016-B0
CDALF10M7GA018-B0
CDALF10M7GA046-B0
CDALF10M7GA048-B0
CDALF10M7GA092-B0
CDALF10M7CA005A-B0
CDALF10M7CA040-B0
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
10.700 ±30kHz
300 min.
300 min.
330 min.
400 min.
300 min.
100 min.
130 min.
within60 to 90mV
within60 to 90mV
280 min.
0.9 max.
0.9 max.
1.0 max.
1.0 max.
1.0 max.
6.0 max.
0.7 max.
TA8122F
TA8132N
LA1832
700 min.
LA1835
60 min.
TA2132P
LA7770
600 min.
40 min.
TEA5710
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
CDALF10M7GA018-B0: Color dot is different from standard series.
■ Standard Center Frequency Rank Code
CODE
30kHz Step
25kHz Step
10.650MHz±25kHz
10.675MHz±25kHz
10.700MHz±25kHz
10.725MHz±25kHz
10.750MHz±25kHz
Combination A, B, C, D, E
Combination A, B, C
Color Code
Black
D
B
A
C
E
Z
10.64MHz±30kHz
10.67MHz±30kHz
10.70MHz±30kHz
10.73MHz±30kHz
10.76MHz±30kHz
30
Blue
Red
Orange
White
M
81
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Test Circuit
CDALF10M7GA016-B0
CDALF10M7GA018-B0
1F in
Vcc 3V
DC out
AF out
VCC +3V
DC Out AF Out
2.2µ
+
SFELF10M7DF00
+
0.033µ
330p
24 23 22 21 20 19 18 17 16 15 14 13
TA8122F (TOSHIBA)
24 23 22 21 20 19 18 17 16 15 14 13
TA8132N (TOSHIBA)
1
2
3
4
5
6
7
8
9
10 11 12
+
CDALF10M7GA016
1
2
3
4
5
6
7
8
9
10 11 12
22µ
SFELF10M7DF00
IF in
+
Unit
R : Ω
C : F
Unit
R : Ω
C : F
0.022µ
Vcc 3V
CDALF10M7GA046-B0
CDALF10M7GA048-B0
AF OUT
Vt
CSBLA456KE2ZF15
33n
CSBLA456KE2ZF15 0.01µ
L. P. F.
L. P. F.
1200p
5.6k
0.047µ
0.01µ
1µ
1500p
33n
+
22µ
3.3µ
+
+
AFC
+
+
3.3µ
AFC
47n
1µ
Rch
Lch
10µ
10µ
24 23 22 21 20 19 18 17 16 15 14 13
+
5k
15k
1µ
24
+
+
30
1
29
2
28
3
27
4
26
5
25
23
22
21
20
19
18
17
14
16
15
6.8k
LA1832 (SANYO)
LA1835 (SANYO)
1
2
3
4
5
6
7
8
9
10 11 12
300
75
6
7
8
9
10
11
12
13
270
3k
300
75
+
0.047µ
0.047µ
2.2µ
0.047µ
10µ
1µ
CDALF10M7GA046
IF-IN
1µ
3k
1k 1k
+
IF-IN
10µ
0.047µ
20k
0.47µ
+
+ +
10µ
+
100µ
Unit
Unit
R : Ω
C : F
CDALF10M7GA048
VCC(7V)
REG.
R : Ω
C : F
47n
10µ
REG
Vcc (5V)
CDALF10M7GA092-B0
CDALF10M7CA005A-B0
DC OUT
2.2µ
AF OUT
+
DC Bias
+5.2V
DC Bias
+5V
10k
Demod.OUT
CDALF10M7GA092
+
2k
Vcc(3.0V)
10k
220p
DATA OUT
20
1
19
18
17
16
15
14
13
12
9
11
16
15
14
13
12
11
10
9
8
IC : LA7770 (SANYO)
TA2132P(TOSHIBA)
2
3
4
5
6
7
8
10
5p
50
1
2
3
4
5
6
7
+
Vcc=12V
+
-
IF IN
Unit
R : Ω
C : F
Unit
R : Ω
C : F
IF-IN
CDALF10M7CA040-B0
VCC (3V)
+
30
AF-OUT
0.01µ 1µ
0.01µ
10µ
100µ
100µ
+
+
+
DC-OUT
24 23 22 21 20 19 18 17 16 15 14 13
TEA5710 (PHILIPS)
1
2
3
4
5
6
7
8
9
10 11 12
0.01µ
0.22µ
280
0.22µ
50
Unit
R : Ω
C : F
S.S.G.
82
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
■ Frequency Characteristics
CDALF10M7GA016-B0
CDALF10M7GA018-B0
100
10
1
1000
1000
100
10
100
100
AF Output
10
AF Output
Distortion
10
1
Distortion
1
0.1
1
0.1
Input signal conditions
Input signal conditions
Input Level
Mod. Freq.
Freq.Dev.
80dBµ
1000Hz
±22.5kHz
Input Level 80dBµ
Mod. Freq. 1000Hz
Freq. Dev. ±22.5kHz
10.4
10.5
10.6
10.7
10.8
10.9
11.0
10.4
10.5 10.6
10.7 10.8 10.9
11.0
Frequency (MHz)
Frequency (MHz)
CDALF10M7GA046-B0
CDALF10M7GA048-B0
100
100
1000
1000
100
10
AF Output
AF Output
100
10
10
Distortion
10
1
1
Distortion
0.1
1
1
0.1
Input signal conditions
Input signal conditions
Input Level 112dBµ
Mod. Freq. 1000Hz
Freq. Dev. ±75kHz
Input Level
Mod. Freq.
Freq.Dev.
112dBµ
1000Hz
±75kHz
10.4
10.5
10.6
10.7
10.8
10.9
11.0
10.4
10.5
10.6
10.7
10.9 11.0
10.8
Frequency (MHz)
Frequency (MHz)
CDALF10M7GA092-B0
CDALF10M7CA005A-B0
1000
5000
1000
100
500
100
AF Output
100
10
AF Output
Distortion
30
100
10
10
1
Distortion
1
10
0.1
1
Input signal conditions
Input Level 100dBµ
Mod. Freq. 1000Hz
Freq. Dev. ±75kHz
Input signal conditions
Input Level
Mod.Freq.
Freq.Dev.
80dBµ
1000Hz
±22.5kHz
10.6
10.7
10.8
10.4 10.5 10.6
10.7 10.8 10.9
11.0
Frequency (MHz)
Frequency (MHz)
Continued on the following page.
83
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Continued from the preceding page.
■ Frequency Characteristics
CDALF10M7CA040-B0
1000
100
10
100
10
1
AF Output
Distortion
1
0.1
Input signal conditions
Input Level 100dBµ
Mod. Freq. 1000Hz
Freq. Dev. ±22.5kHz
10.4 10.5 10.6
10.7 10.8
10.9
11.0
Frequency (MHz)
30
84
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Ceramic Discriminator 10.7MHz Applied IC Reference Table
Please see following table for reference applied IC.
If you can not find IC part number seeking, please contact our sales representative.
ex. : CDALF10M7GA016-B0
Suffix Number
CDSCB10M7GA105A-R0
Suffix Number
IC Manufacturer
ATMEL
IC Part Number
U2501B
Suffix Number
028
IC Manufacturer
IC Part Number
KA22425
KA2244
Suffix Number
089
059
090
063
064
091
065
103
118A
070
108A
007
026
022
115
015
094
101
083
037
043
046
086
048
079
023
114
121
078
001
002
012
093
027
027N
032
054
069
075
117
068
076
119
SAMSUNG
U2765B
095
U4313B
081
KA22901
KA2292
U4490B
034V
025
U829B
KA2295
INFINEON
TDA1576T
TDA6160X
TDA6160-2X
AN6138SH
AN7004
051
KA2297
038
KA2298B
KB22902
S1A0903
LA1150
044
MATSUSHITA
097
011
SANYO
AN7006S
AN7007SU
AN7232
014A
013
LA1225M
LA1260
053
LA1805
MOTOROLA
MC13156
MC13158
MC13173
MC3363
049
LA1810
073
LA1814M
LA1816
052
087
LA1822
NEC
µPC1391M
NE604
056
LA1823
PHILIPS
020
LA1827M
LA1830
SA605
042
SA626
047
LA1831
SA636DK
SA639
096
LA1832 / M
LA1833
085
TBA120U
TBA229-2
TDA1596T
TDA2557
TEA5591
TEA5592
TEA5594
TEA5710
TEA5712T
TEA5757HL
TEA5762 / 5757
UAA3220TS
RF2905
029
LA1835 / M
LA1838 / M
LA7770
021A
120
024
LV23000M
LV23100V
CX1691M
CX-20029
CX-20076
CXA1030P
CXA1111
CXA1238
CXA1238N
CX1343M
CXA1376AM
CXA1538M / N / S
CXA1611
CXA1619B
CXA1991N
CX3067M
TRF6901
017
030
SONY
035
040
055
105A
061
098
111
RFMD
ROHM
30
RF2925
104
BA1440
019
BA1448
060
BA4110
066
BA4220
041
BA4230AF
BA4234L
BA4240L
005
004
T. I.
067
Continued on the following page.
85
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Ceramic Discriminator 10.7MHz Applied IC Reference Table
Continued from the preceding page.
IC Manufacturer
TOKO
IC Part Number
TK14570L
TK14581
Suffix Number
122
062
TK14583V
TK14588V
TA2003
112
109
TOSHIBA
031
TA2007
033
TA2008A / AN
TA2022
045
050
TA2029
036
TA2046
058
TA2057
057
TA2099N
082
TA2104AFN
TA2104F
080
080A
077
TA2111N / F / FN
TA2132
092
TA2132BP
TA2142FN
TA2149AN
TA2149N
092D
102
100A
100
TA2154FN
TA2159F
113
116
TA31161
072
TA31275FN
TA7130P
123
009
TA7303P
008
TA7640AP
TA7765AF
TA8122AN / AF
TA8132AN / AF
TA8186
006
071
016
018
039
TA8721ASN
TB2132FN
088
128
30
86
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
CERAFILr (Filters/ Traps/ Discriminators) for Audio/ Visual Equipment
Ceramic Discriminator 3.5-6.5MHz Wide Bandwidth Type CDSRF Series
10.0 max.
Ceramic discriminator CDSRF series is a wide band, low
profile type using thickness shear mode vibration.
E I A J
C O D E
M A R K I N G
■ Features
1. Low profile 8.0mm type
1.38±0.2
2. Suitable for Multi-sound Broadcasting system
3. Two-terminals type and three-terminals type are
available.
0.5±0.1
5.0±0.2
CDSRF_EK Series
(in mm)
10.0 max.
EIAJ
M A R K I N G
CODE
1.38±0.2
1.7±0.1
0.5±0.1
2.5±0.2 2.5±0.2
(1) : Input
(2) : Ground
(3) : Output
CDSRF_CK Series
(in mm)
(3) (2) (1)
Nominal Center
Frequency (fn)
(MHz)
Recovered
Audio 3dB BW
(kHz)
Recovered Audio
Output Voltage (at fn)
(mV)
Distortion
(% )
Part Number
IC
CDSRF4M50EK020-B0
CDSRF4M50EK023-B0
CDSRF4M50EK035-B0
CDSRF4M50EK049-B0
CDSRF4M50EK060-B0
CDSRF4M50EK069-B0
CDSRF4M50EK070-B0
CDSRF5M50EK023-B0
CDSRF5M50EK035-B0
CDSRF5M50EK049-B0
CDSRF5M50EK054-B0
CDSRF5M50EK060-B0
CDSRF5M74EK054-B0
CDSRF6M00EK049-B0
CDSRF6M00EK054-B0
CDSRF6M00EK060-B0
CDSRF6M50EK020-B0
CDSRF6M50EK049-B0
CDSRF6M50EK054-B0
CDSRF6M50EK060-B0
CDSRF4M50CK020-B0
CDSRF4M50CK026-B0
CDSRF4M50CK029-B0
CDSRF4M50CK030-B0
4.500
4.500
4.500
4.500
4.500
4.500
4.500
5.500
5.500
5.500
5.500
5.500
5.742
6.000
6.000
6.000
6.500
6.500
6.500
6.500
4.500
4.500
4.500
4.500
fn±80 min.
fn±60 min.
fn±55 min.
fn±100 min.
fn±90 min.
fn±60 min.
fn±50 min.
fn±45 min.
fn±80 min.
fn±60 min.
fn±100 min.
fn±70 min.
fn±90 min.
fn±60 min.
fn±90 min.
fn±60 min.
fn±110 min.
fn±60 min.
fn±90 min.
fn±60 min.
fn±50 min.
fn±40 min.
fn±65 min.
fn±40 min.
245 min.
230 min.
240 min.
220 min.
90 min.
1.0 max.
2.5 max.
1.0 max.
1.0 max.
1.0 max.
1.5 max.
1.5 max.
1.0 max.
1.0 max.
1.0 max.
1.2 max.
1.5 max.
1.2 max.
1.0 max.
1.5 max.
2.5 max.
1.2 max.
1.0 max.
1.5 max.
2.5 max.
2.0 max.
1.2 max.
1.2 max.
3.0 max.
LA7550/7555
M51496P
LA7680/7681
LA7577
M52318SP
TA8701N
M52007FP
M51496P
LA7680/7681
LA7577
320 min.
65 min.
220 min.
350 min.
500 min.
300 min.
190 min.
340 min.
500 min.
340 min.
180 min.
350 min.
500 min.
340 min.
160 min.
280 min.
70 min.
TDA3857
M52318SP
TDA3857
LA7577
TDA3857
M52318SP
LA7550/7555
LA7577
31
TDA3857
M52318SP
µPC1382C
LA7530
250 min.
within130 +30/-20mV
M51365SP
M51348FP
Continued on the following page.
87
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Continued from the preceding page.
Nominal Center
Frequency (fn)
(MHz)
Recovered
Audio 3dB BW
(kHz)
Recovered Audio
Output Voltage (at fn)
(mV)
Distortion
(% )
Part Number
IC
CDSRF5M50CK026-B0
CDSRF5M50CK029-B0
CDSRF5M50CK030-B0
CDSRF6M00CK026-B0
CDSRF6M00CK029-B0
CDSRF6M00CK030-B0
CDSRF6M50CK020-B0
CDSRF6M50CK026-B0
CDSRF6M50CK029-B0
5.500
5.500
5.500
6.000
6.000
6.000
6.500
6.500
6.500
fn±50 min.
fn±70 min.
fn±55 min.
fn±50 min.
fn±70 min.
fn±55 min.
fn±60 min.
fn±35 min.
fn±70 min.
500 min.
420 min.
150 min.
400 min.
450 min.
150 min.
480 min.
400 min.
430 min.
3.0 max.
1.5 max.
3.0 max.
3.0 max.
1.7 max.
3.0 max.
2.0 max.
3.0 max.
2.0 max.
LA7530
M51365SP
M51348FP
LA7530
M51365SP
M51348FP
µPC1382C
LA7530
M51365SP
Characteristics shown above is as of 100% Dev.
Part Numbers are varied with applied IC.
Please note circuits and specifications are also varied with IC.
For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the package page.
■ Test Circuit
CDSRF4M50EK049-B0
CDSRF4M50CK029-B0
12p
IF-in
(1)
(3)
(2)
18
0.01µ
24 23 22 21 20 19 18 17 16 15 14 13
DC Out
AF Out
17
19
IN
13
4.7µ
LA7577 (SANYO)
M51365SP
(MITSUBISHI)
+
1
2
3
4
5
6
7
8
9
10 11 12
14
5.6k
7
10 12
AF-out
Vcc (12V)
Vcc=12V
Ground
+
10µ
Unit C : F
R : Ω
Ground
L : H
Unit C : F
R : Ω
■ Frequency Characteristics
CDSRF4M50EK049-B0
CDSRF4M50CK029-B0
300
100
300
AF Output
AF Output
10
100
10
10
1
10
1
Distoriton
Distoriton
1
1
0.1
0.1
4.3
4.5
4.7
4.3
4.5
4.7
31
Frequency (MHz)
Frequency (MHz)
88
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Notice (Soldering and Mounting)
■ CERAFILr 10.7MHz Chip Type SFECF Series
1. Standard Reflow Soldering Conditions
(1) Reflow
Filter is soldered twice within the following temperature
conditions.
Peak
(260°C max.)
260
230
Heating
(230°C)
Pre-heating
(150-180°C)
100
Gradual
Cooling
30 sec.
min.
40 sec.
max.
120 sec.
min.
60-120 sec.
(2) Soldering Iron
Filter is soldered at +350±5°C for 3.0±0.5 seconds. The
soldering iron should not touch the filter while soldering.
2. Wash
The component cannot withstand washing.
■ CERAFILr 10.7MHz Chip Type SFECD Series
1. Standard Reflow Soldering Conditions
(1) Reflow
Filter is soldered twice within the following temperature
conditions.
Peak
(260°C max.)
260
230
Heating
(230°C)
Pre-heating
(150-180°C)
100
Gradual
Cooling
30 sec.
min.
40 sec.
max.
120 sec.
min.
60-120 sec.
(2) Soldering Iron
Filter is soldered at +350±5°C for 3.0±0.5 seconds. The
soldering iron should not touch the filter while soldering.
2. Wash
The component cannot withstand washing.
Continued on the following page.
31
89
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Notice (Soldering and Mounting)
Continued from the preceding page.
■ CERAFILr 10.7MHz Chip Type SFECV Series
1. Standard Reflow Soldering Conditions
(1) Reflow
Filter is soldered twice within the following temperature
conditions.
Peak
(240°C max.)
240
230
Heating
(230°C)
Pre-heating
(150-180°C)
100
Gradual
Cooling
30 sec.
min.
30 sec.
max.
120 sec.
min.
60-120 sec.
(2) Soldering Iron
Filter is soldered at +350±5°C for 3.0±0.5 seconds. The
soldering iron should not touch the filter while soldering.
2. Wash
The component cannot withstand washing.
■ CERAFILr 10.7MHz Lead Type
The component cannot withstand washing.
■ CERAFILr 4.5-6.5MHz Chip Type
1. Standard Reflow Soldering Conditions
(1) Reflow
Filter is soldered twice within the following temperature
conditions.
Peak
(240°C max.)
240
230
Heating
(230°C)
Pre-heating
(150-180°C)
100
Gradual
Cooling
30 sec.
min.
30 sec.
max.
120 sec.
min.
60-120 sec.
(2) Soldering Iron
Filter is soldered at +350±5°C for 3.0±0.5 seconds. The
soldering iron should not touch the filter while soldering.
2. Wash
The component cannot withstand washing.
31
■ CERAFILr 3.5-6.5MHz Lead Type
The component cannot withstand washing.
90
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Notice (Soldering and Mounting)
■ CERAFILr 455kHz Chip Type PFWCC Series
1. Standard Reflow Soldering Conditions
(1) Reflow
Filter is soldered twice within the following temperature
conditions.
Peak
(250°C max.)
250
220
Heating
(220°C)
Pre-heating
(150-180°C)
100
Gradual
Cooling
30 sec.
min.
20 sec.
max.
120 sec.
min.
60-120 sec.
(2) Soldering Iron
Filter is soldered at +350±5°C for 3.0±0.5 seconds. The
soldering iron should not touch the filter while soldering.
2. Wash
The component cannot withstand washing.
Continued on the following page.
31
91
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Notice (Soldering and Mounting)
Continued from the preceding page.
■ CERAFILr 455kHz Chip Type SFPKA Series
1. Standard Reflow Soldering Conditions
(1) Reflow
Filter is soldered twice within the following temperature
conditions.
Peak
(260°C max.)
260
230
Heating
(230°C)
Pre-heating
100
(150-180°C)
Gradual
Cooling
30 sec.
min.
60-120 sec.
40 sec.
max.
120 sec.
min.
(2) Soldering Iron
Electrode is soldered directly with the tip of soldering iron
at +350±5°C for 3.0±0.5 seconds.
2. Wash
(1) Cleaning Solvent
CFC alternatives (HCFC Series), Isopropyl Alcohol (IPA),
Water (Demineralized Water), Cleaning Water Solution
(Cleanthrough-750H, Pine Alpha 100S), Silicon
(Technocare FRW)
(2) Cleaning Conditions
Immersion Wash
2 minutes max. in above solvent at +60°C max.
Shower or Rinse Wash
2 minutes max. in above solvent at +60°C max.
(3) Notice
When components are immersed in solvent, be sure to
maintain the temperature of components below the
temperature of solvent.
Please do not use ultrasonic cleaning.
Total washing time should be within 4 minutes.
Please ensure the component is thoroughly evaluated
in your application circuit.
Please do not use chlorine, petroleum and alkaline
cleaning solvents.
If you plan to use any other type of solvents, please
consult with Murata or Murata representative prior to
using.
■ CERAFILr 455kHz Lead Type
The component cannot withstand washing.
31
92
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Notice (Soldering and Mounting)
■ Ceramic Trap 4.5-6.5MHz Chip Type
1. Standard Reflow Soldering Conditions
(1) Reflow
Filter is soldered twice within the following temperature
conditions.
Peak
(240°C max.)
240
230
Heating
(230°C)
Pre-heating
(150-180°C)
100
Gradual
Cooling
30 sec.
min.
30 sec.
max.
120 sec.
min.
60-120 sec.
(2) Soldering Iron
Filter is soldered at +350±5°C for 3.0±0.5 seconds. The
soldering iron should not touch the filter while soldering.
2. Wash
The component cannot withstand washing.
■ Ceramic Trap 3.5-6.5MHz Lead Type
The component cannot withstand washing.
■ Ceramic Discriminator 10.7MHz Chip Type
1. Standard Reflow Soldering Conditions
(1) Reflow
Filter is soldered twice within the following temperature
conditions.
Peak
(260°C max.)
260
230
Heating
(230°C)
Pre-heating
(150-180°C)
100
Gradual
Cooling
30 sec.
min.
40 sec.
max.
120 sec.
min.
60-120 sec.
(2) Soldering Iron
Filter is soldered at +300±5°C for 3.0±0.5 seconds. The
soldering iron should not touch the filter while soldering.
2. Wash
31
The component cannot withstand washing.
■ Ceramic Discriminator 10.7MHz Lead Type
The component cannot withstand washing.
■ Ceramic Discriminator 3.5-6.5MHz
The component cannot withstand washing.
93
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Notice (Handling)
■ CERAFILr 10.7MHz Chip Type SFECF Series
1. The component will be damaged when an excessive
stress is applied.
[Component layout close to board]
2. The component may be damaged if excess mechanical
stress is applied to it mounted on the printed circuit
board.
Perforation
A
B
Susceptibility to
stress is in the order
of : A>C>B
C
Slit
3. Design layout of components on the PC board to
minimize the stress imposed on the warp or flexure of the
board.
4. After installing chips, if solder is excessively applied to
the circuit board, mechanical stress will cause destruction
resistance characteristics to lower. To prevent this, be
extremely careful in determining shape and dimension
before designing the circuit board diagram.
5. The component may be damaged during mounting
process if some part of mounter such as positioning
claws, nozzle are worn down. The regular maintenance
recommended for mounters should be done to prevent
the troubles.
6. The component is recommended with placement
machines which employ optical placement capabilities.
The component might be damaged by excessive
mechanical force. Please make sure that you have
evaluated by using placement machines before going into
mass production. Do not use placement machines which
utilize mechanical positioning. Please contact Murata for
details beforehand.
7. When correcting chips with a soldering iron, the tip of the
soldering iron should not directly touch the chip
component. Depending on the soldering conditions, the
effective area of terminations may be reduced. The use
of solder containing Ag should be done to prevent the
electrode erosion.
8. Do not clean or wash the component as it is not
hermetically sealed.
9. In case of covering filter with over coat, conditions such
as material of resin, cure temperature, and so on should
be evaluated carefully.
10. Do not use strong acidity flux, more than 0.2wt%
chlorine content, in re-flow soldering.
11. Accurate test circuit values are required to measure
electrical characteristics.
It may be a cause of miscorrelation if there is any
deviation, especially stray capacitance, from the test
circuit in the specification.
12. The components, packed in the moisture proof bag (dry
pack), are sensitive to moisture. The following treatment
is required before applying re-flow soldering. To avoid
reliability degradation caused by thermal stress. When
unpacked, store the component in an atmosphere at
30°C and below 60%R.H., and solder within 1 week.
13. For safety purposes, connect the output of filters to the
IF amplifier through a D.C. blocking capacitor. Avoid
applying a direct current to the output of ceramic filters.
31
Continued on the following page.
94
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Notice (Handling)
Continued from the preceding page.
■ CERAFILr 10.7MHz Chip Type SFECD Series
1. The component will be damaged when an excessive
stress is applied.
[Component layout close to board]
2. The component may be damaged if excess mechanical
stress is applied to it mounted on the printed circuit
board.
Perforation
A
B
Susceptibility to
stress is in the order
of : A>C>B
C
Slit
3. Design layout of components on the PC board to
minimize the stress imposed on the warp or flexure of the
board.
4. After installing chips, if solder is excessively applied to
the circuit board, mechanical stress will cause destruction
resistance characteristics to lower. To prevent this, be
extremely careful in determining shape and dimension
before designing the circuit board diagram.
5. The component may be damaged during mounting
process if some part of mounter such as positioning
claws, nozzle are worn down. The regular maintenance
recommended for mounters should be done to prevent
the troubles.
6. The component is recommended with placement
machines which employ optical placement capabilities.
The component might be damaged by excessive
mechanical force. Please make sure that you have
evaluated by using placement machines before going into
mass production. Do not use placement machines which
utilize mechanical positioning. Please contact Murata for
details beforehand.
7. When correcting chips with a soldering iron, the tip of the
soldering iron should not directly touch the chip
component. Depending on the soldering conditions, the
effective area of terminations may be reduced. The use
of solder containing Ag should be done to prevent the
electrode erosion.
8. Do not clean or wash the component as it is not
hermetically sealed.
9. In case of covering filter with over coat, conditions such
as material of resin, cure temperature, and so on should
be evaluated carefully.
10. Do not use strong acidity flux, more than 0.2wt%
chlorine content, in re-flow soldering.
11. Accurate test circuit values are required to measure
electrical characteristics.
It may be a cause of miscorrelation if there is any
deviation, especially stray capacitance, from the test
circuit in the specification.
12. The components, packed in the moisture proof bag (dry
pack), are sensitive to moisture. The following treatment
is required before applying re-flow soldering. To avoid
reliability degradation caused by thermal stress. When
unpacked, store the component in an atmosphere at
30°C and below 60%R.H., and solder within 1 week.
13. For safety purposes, connect the output of filters to the
IF amplifier through a D.C. blocking capacitor. Avoid
applying a direct current to the output of ceramic filters.
31
Continued on the following page.
95
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Notice (Handling)
Continued from the preceding page.
■ CERAFILr 10.7MHz Chip Type SFECV Series
1. The component will be damaged when an excessive
stress is applied.
[Component direction]
Put the
2. The component may be damaged if excess mechanical
stress is applied to it mounted on the printed circuit
board.
component
lateral to the
direction in
which stress
acts.
3. Design layout of components on the PC board to
minimize the stress imposed on the warp or flexure of the
board.
[Component layout close to board]
Perforation
B
Susceptibility to
stress is in the order
of : A>C>B
4. After installing chips, if solder is excessively applied to
the circuit board, mechanical stress will cause
destruction resistance characteristics to lower. To
prevent this, be extremely careful in determining shape
and dimension before designing the circuit board
diagram.
C
A
Slit
5. The component may be damaged during mounting
process if some part of mounter such as positioning
claws, nozzle are worn down. The regular maintenance
recommended for mounters should be done to prevent
the troubles.
6. The component is recommended with placement
machines which employ optical placement capabilities.
The component might be damaged by excessive
mechanical force. Please make sure that you have
evaluated by using placement machines before going
into mass production. Do not use placement machines
which utilize mechanical positioning. Please contact
Murata for details beforehand.
7. When correcting chips with a soldering iron, the tip of the
soldering iron should not directly touch the chip
component. Depending on the soldering conditions, the
effective area of terminations may be reduced. The use
of solder containing Ag should be done to prevent the
electrode erosion.
8. Do not clean or wash the component as it is not
hermetically sealed.
9. In case of covering filter with over coat, conditions such
as material of resin, cure temperature, and so on should
be evaluated carefully.
10. Do not use strong acidity flux, more than 0.2wt%
chlorine content, in re-flow soldering.
11. Accurate test circuit values are required to measure
electrical characteristics. It may be a cause of mis-
correlation if there is any deviation, especially stray
capacitance, from the test circuit in the specification.
12. For safety purposes, connect the output of filters to the
IF amplifier through a D.C. blocking capacitor. Avoid
applying a direct current to the output of ceramic filters.
31
96
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Notice (Handling)
■ CERAFILr 10.7MHz Lead Type
1. Do not use this product with bend. The component
may be damaged if excess mechanical stress is
applied to it mounted on the printed circuit board.
2. The component may be damaged when an excessive stress
is applied.
7. Accurate test circuit values are required to
measure electrical characteristics. It may be a
cause of miscorrelation if there is any deviation,
especially stray capacitance, from the test
circuit in the specification.
3. All kinds of re-flow soldering must not be applied
on the component.
8. For safety purposes, connect the output of filters
to the IF amplifier through a D.C. blocking
capacitor. Avoid applying a direct current to the
output of ceramic filters.
4. Do not clean or wash the component as it is not
hermetically sealed.
5. Do not use strong acidity flux, more than 0.2wt%
chlorine content, in flow soldering.
6. In case of covering discriminator with over coat,
conditions such as material of resin, cure
temperature, and so on should be evaluated
carefully.
■ CERAFILr 4.5-6.5MHz Chip Type
1. The component may be damaged if excess mechanical
stress is applied to it mounted on the printed circuit
board.
[Component direction]
Put the compon-
ent lateral to
the direction in
which stress
acts.
2. Design layout of components on the PC board to
minimize the stress imposed on the wrap or flexure of the
board.
[Component layout close to board]
3. After installing chips, if solder is excessively applied to
the circuit board, mechanical stress will cause destruction
resistance characteristics to lower. To prevent this, be
extremely careful in determining shape and dimension
before designing the circuit board diagram.
4. The component may be damaged during mounting
process if some part of mounter such as positioning
claws, nozzle are worn down. The regular maintenance
recommended for mounters should be done to prevent
the troubles.
Susceptibility to
stress is in the order
of : A>C>B
Perforation
A
B
C
Slit
5. When correcting chips with a soldering iron, the tip of the
soldering iron should not directly touch the chip
component.
6. Cleaning or washing of the component is not acceptable
due to non sealed construction.
7. In case of covering filter with over coat, conditions such
as material of resin, cure temperature, and so on should
be evaluated carefully.
8. Accurate test circuit values are required to measure
electrical characteristics. It may be a cause of
miscorrelation if there is any deviation, especially stray
capacitance, from the test circuit in the specification.
9. For safety purposes, connect the output of filters to the IF
amplifier through a D.C. blocking capacitor. Avoid
applying a direct current to the output of ceramic filters.
31
97
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Notice (Handling)
■ CERAFILr 3.5-6.5MHz Lead Type
1. Do not use this product with bend. The component
may be damaged if excess mechanical stress is
applied to it mounted on the printed circuit board.
2. The component may be damaged when an excessive stress
is applied.
7. In case of covering filter with over coat,
conditions such as material of resin, cure
temperature, and so on should be evaluated
carefully.
8. Accurate test circuit values are required to
measure electrical characteristics. It may be a
cause of miscorrelation if there is any
deviation, especially stray capacitance, from the
test circuit in the specification.
3. All kinds of re-flow soldering must not be applied
on the component.
4. Do not clean or wash the component as it is not
hermetically sealed.
5. Please contact Murata or Murata representative for
soldering condition, in case of using lead free
solder.
9. For safety purposes, connect the output of filters
to the IF amplifier through a D.C. blocking
capacitor. Avoid applying a direct current to the
output of ceramic filters.
6. Do not use strong acidity flux, more than 0.2wt%
chlorine content, in flow soldering.
■ CERAFILr 455kHz Chip Type PFWCC Series
1. The component may be damaged if excess mechanical
stress is applied to it mounted on the printed circuit
board.
[Component direction]
Put the
component
lateral to the
direction in
which stress
acts.
2. Design layout of components on the PC board to
minimize the stress imposed on the warp or flexure of the
board.
[Component layout close to board]
3. After installing chips, if solder is excessively applied to
the circuit board, mechanical stress will cause destruction
resistance characteristics to lower. To prevent this, be
extremely careful in determining shape and dimension
before designing the circuit board diagram.
Perforation
B
Susceptibility to
stress is in the order
of : A>C>B
C
A
Slit
4. For safety purposes, connect the output of filters to the IF
amplifier through a D.C. blocking capacitor. Avoid
applying a direct current to the output of ceramic filters.
■ CERAFILr 455kHz Chip Type SFPKA Series
1. The component will be damaged when an excessive
stress is applied.
6. The product, packed in the moisture-proof bag
(dry pack), is sensitive to moisture. The following
treatment is required before applying re-flow
soldering, to avoid package cracks or reliability
degradation caused by thermal stress. When unpacked,
store the component in an atmosphere of below 25
degree C and below 65%R.H., and solder within 48
hours.
2. Use coupling capacitors to prevent applying D.C.
voltage between input-ground, output-ground of
"CERAFIL" as D.C. current may harm the component.
3. In the case that the component is cleaned, confirm
that no reliability degradation is created.
4. In case of covering filter with over coat,
conditions such as material of resin, cure
temperature, and so on should be evaluated
carefully.
7. For safety purposes, connect the output of filters
to the IF amplifier through a D.C. blocking
capacitor. Avoid applying a direct current to the
output of ceramic filters.
5. Do not use strong acidity flux, more than 0.2wt%
chlorine content, in re-flow soldering.
31
98
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Notice (Handling)
■ CERAFILr 455kHz Lead Type
1. Do not use this product with bend. The component
may be damaged if excess mechanical stress is
applied to it mounted on the printed circuit board.
2. The component will be damaged when an excessive
stress is applied.
7. Accurate test circuit values are required to
measure electrical characteristics.
It may be a cause of miscorrelation if there is
any deviation, especially stray capacitance, from
the test circuit in the specification.
3. All kinds of re-flow soldering must not be applied
on the component.
8. Use coupling capacitors to prevent applying D.C.
voltage between input-ground, output-ground of
"CERAFIL" as D.C. current may harm the component.
9. For safety purpose, connect the output of filters to
the IF amplifier through a D.C. blocking capacitor.
Avoid appliying a direct current to the output of
ceramic filters.
4. Do not clean or wash the component as it is not
hermetically sealed.
5. Do not use strong acidity flux, more than 0.2wt%
chlorine content, in flow soldering.
6. In case of covering filter with over coat,
conditions such as material of resin, cure
temperature, and so on should be evaluated
carefully.
■ Ceramic Trap 4.5-6.5MHz Chip Type
1. The component may be damaged if excess mechanical
stress is applied to it mounted on the printed circuit
board.
[Component direction]
Put the compon-
ent lateral to
the direction in
which stress
acts.
2. Design layout of components on the PC board to
minimize the stress imposed on the wrap or flexure of the
board.
[Component layout close to board]
3. After installing chips, if solder is excessively applied to
the circuit board, mechanical stress will cause destruction
resistance characteristics to lower. To prevent this, be
extremely careful in determining shape and dimension
before designing the circuit board diagram.
4. The component may be damaged during mounting
process if some part of mounter such as positioning
claws, nozzle are worn down. The regular maintenance
recommended for mounters should be done to prevent
the troubles.
Susceptibility to
stress is in the order
of : A>C>B
Perforation
A
B
C
Slit
5. When correcting chips with a soldering iron, the tip of the
soldering iron should not directly touch the chip
component.
6. Cleaning or washing of the component is not acceptable
due to non sealed construction.
7. In case of covering filter with over coat, conditions such
as material of resin, cure temperature, and so on should
be evaluated carefully.
8. Accurate test circuit values are required to measure
electrical characteristics. It may be a cause of
miscorrelation if there is any deviation, especially stray
capacitance, from the test circuit in the specification.
9. For safety purposes, connect the output of filters to the IF
amplifier through a D.C. blocking capacitor. Avoid
applying a direct current to the output of ceramic filters.
31
99
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Notice (Handling)
■ Ceramic Trap 3.5-6.5MHz Lead Type
1. Do not use this product with bend. The component
may be damaged if excess mechanical stress is
applied to it mounted on the printed circuit board.
2. The component may be damaged when an excessive stress
is applied.
7. In case of covering filter with over coat,
conditions such as material of resin, cure
temperature, and so on should be evaluated
carefully.
8. Accurate test circuit values are required to
measure electrical characteristics. It may be a
cause of miscorrelation if there is any
deviation, especially stray capacitance, from the
test circuit in the specification.
3. All kinds of re-flow soldering must not be applied
on the component.
4. Do not clean or wash the component as it is not
hermetically sealed.
5. Please contact Murata or Murata representative for
soldering condition, in case of using lead free
solder.
9. For safety purposes, connect the output of filters
to the IF amplifier through a D.C. blocking
capacitor. Avoid applying a direct current to the
output of ceramic filters.
6. Do not use strong acidity flux, more than 0.2wt%
chlorine content, in flow soldering.
■ Ceramic Discriminator 10.7MHz Chip Type
1. The component mounted on the PCB may be damaged if
excess mechanical stress is applied.
[Component direction]
Put the
component
laterally to the
direction in
which stress
acts.
2. Layout the components on the PCB to minimize the
stress imposed on the warp or flexure of the board.
3. After installing components, if solder is excessively
applied to the circuit board, mechanical stress will cause
destruction resistance characteristics to be lower. To
prevent this, be extremely careful in determining shape
and dimension before designing the circuit board diagram.
4. The component may be damaged during mounting
process if some part of mounter such as positioning
claws, nozzle are worn down. The regular maintenance
recommended for mounters should be done to prevent
the troubles.
[Component layout close to board]
Perforation
B
Susceptibility to
stress is in the order
of : A>C>B
C
A
Slit
5. When correcting component's position with a soldering
iron, the tip of the soldering iron should not directly touch
the chip component. Depending on the soldering
conditions, the effective area of terminations may be
reduced. The use of solder containing Ag should be
considerd to prevent the electrode erosion.
6. Do not clean or wash the component as it is not
hermetically sealed.
7. In case of overcoating the part, coating conditions such
as material of resin, curing temperature, and so on
should be evaluated carefully.
8. Accurate test circuit values are required to measure
electrical characteristics.
It may be a cause of miscorrelation if there is any
deviation, especially stray capacitance, from the test
circuit in the specification.
9. For safety purposes, connect the output of filters to the IF
amplifier through a D.C. blocking capacitor. Avoid
applying a direct current to the output of ceramic filters.
31
100
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Notice (Handling)
■ Ceramic Discriminator 10.7MHz Lead Type
1. Do not use this product with bend. The component
may be damaged if excess mechanical stress is
applied to it mounted on the printed circuit board.
2. The component may be damaged when an excessive stress
is applied.
7. Accurate test circuit values are required to
measure electrical characteristics. It may be a
cause of miscorrelation if there is any deviation,
especially stray capacitance, from the test
circuit in the specification.
3. All kinds of re-flow soldering must not be applied
on the component.
8. For safety purposes, connect the output of filters
to the IF amplifier through a D.C. blocking
capacitor. Avoid applying a direct current to the
output of ceramic filters.
4. Do not clean or wash the component as it is not
hermetically sealed.
5. Do not use strong acidity flux, more than 0.2wt%
chlorine content, in flow soldering.
6. In case of covering discriminator with over coat,
conditions such as material of resin, cure
temperature, and so on should be evaluated
carefully.
■ Ceramic Discriminator 3.5-6.5MHz
1. Do not use this product with bend. The component
may be damaged if excess mechanical stress is
applied to it mounted on the printed circuit board.
2. The component may be damaged when an excessive stress
is applied.
7. In case of covering filter with over coat,
conditions such as material of resin, cure
temperature, and so on should be evaluated
carefully.
8. Accurate test circuit values are required to
measure electrical characteristics. It may be a
cause of miscorrelation if there is any
deviation, especially stray capacitance, from the
test circuit in the specification.
3. All kinds of re-flow soldering must not be applied
on the component.
4. Do not clean or wash the component as it is not
hermetically sealed.
5. Please contact Murata or Murata representative for
soldering condition, in case of using lead free
solder.
9. For safety purposes, connect the output of filters
to the IF amplifier through a D.C. blocking
capacitor. Avoid applying a direct current to the
output of ceramic filters.
6. Do not use strong acidity flux, more than 0.2wt%
chlorine content, in flow soldering.
31
101
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Packaging
■ Minimum Quantity
Taping
Ammo Pack
Bulk
Magazine
Box
ø330mm
ø180mm
CERAFILr<10.7MHz>
SFECD
SFECF
SFECV
SFELF
SFELG
SFKLF
SFTLF
SFVLF
2,000
2,000
2,000
1,500
1,500
1,500
500
500
500
500
500
1,000
CERAFILr<3.5-6.5MHz>
CERAFILr<455kHz>
SFSKA
SFSRA
SFSRF
3,000
2,000
1,500
500
500
BFULA
CFULA
CFWLA
PFSLF
PFWCC
PFWLF
SFPKA
SFPLA
SFULA
SFZLA
500
200
150
50
1,500
1,500
500
500
1,000
1,000
50
50
50
200
500
200
Ceramic Traps<3.5-6.5MHz>
TPSKA
TPSRA
TPSRF
TPTRF
TPWKA
TPWRF
3,000
3,000
2,000
1,500
1,500
500
500
500
1,500
1,500
500
500
Ceramic Discriminators<10.7MHz>
Ceramic Discriminators<3.5-6.5MHz>
CDALF
CDSCB
2,000
CDSRF
1,500
500
31
102
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Packaging
■ CERAFILr 10.7MHz Chip Type SFECF Series
Dimensions of Carrier Tape
Dimensions of Reel
40T0.15
Trailer
160-190
Leader
Cover film
10 pitch accumulated
4.0T0.1
ø1.55T0.05 2.0T0.05
Empty
240-280
Empty Components
Chip filter
ø13.0±0.5
400-560
2.0±0.5
+0.1
4.0T0.1
Peeling strength
(0.1 to 0.7N)
3.35
-0.05
17.0±1.0
3˚ max.
10˚ max.
+1.0
13.0
Cover film
-0
User direction of feed
( ) : Reference
(in mm)
• Part number marked side is always facing upside.
• The feeding holes side of cavity tape is always input terminal.
■ CERAFILr 10.7MHz Chip Type SFECD Series
Dimensions of Carrier Tape
Dimensions of Reel
Trailer
160-190
Leader
Cover film
40T0.15
10 pitch accumulated
4.0T0.1
ø1.55T0.05
2.0T0.05
Empty Components
Empty
240-280
Chip Filter
ø13.0±0.5
400-560
2.0±0.5
3.35T0.1
Peeling strength
0.1 to 0.7N
4.0T0.1
10˚ max.
3˚ max.(3.4)
+1.0
12.5 -0
Cover film
19.5 max.
User direction of feed
· Part Number marked side is always facing upside.
· The feeding holes side of cavity tape is always input terminal.
(
) : Reference
(in mm)
■ CERAFILr 10.7MHz Chip Type SFECV Series
Dimensions of carrier tape
Dimension of reel
Trailer
160-190
Leader
Cover film
ø1.5YW00..01
2.0T0.05
4.0T0.1
Empty
240-280
Empty Components
ø13.0±0.5
400-560
2.0±0.5
4.0T0.1
Peeling strengh 0.1 to 0.7N
Cover film
3.0T0.1
Chip filter
31
+1.0
3° max.
13.0
-0
10° max.
17.0±1.0
User direction of feed
• Part number marked side is always facing upside.
• The feeding holes side of cavity tape is always input terminal.
(
) : Reference
(in mm)
Continued on the following page.
103
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Packaging
Continued from the preceding page.
■ CERAFILr 10.7MHz Lead Type SF_LF Series
dh dh
P2
P
dS1
F1 F1
D0
P1
F
t
P0
Item
Lead length under the hold down tape
Length of cut off
Code
L1
Dimensions
3.0 min.
2.0 max.
12.7
Tolerance
Remarks
-
L2
-
To distinguish the direction
Pitch of components
P
±0.5
±0.2
±0.5
±0.5
Pitch of sprocket hole (1)
Length from hole center to lead
P0
P1
P2
F
12.7
3.85
Length from hole center to component center
Lead spacing (1)
6.35
+0.5
5.0
–0.2
Lead spacing (2)
F1
2.5
±0.2
±1.0
±1.0
±0.5
-
Slant to the forward or backward
Slant to the left or right
dh
dS1
W
0
0
Width of carrier tape
18.0
Width of hold down tape
Position of sprocket hole
W0
W1
6.0 min.
9.0
±0.5
Hold down tape doesn't exceed
the carrier tape
+0.5
–0
Gap of hold down tape and carrier tape
W2
H0
0
Distance between the center of sprocket
hole and lead stopper
18.0
±0.5
Diameter of sprocket hole
Total tape thickness
D0
t
ø4.0
0.6
±0.2
±0.2
±1.5
Pitch of sprocket hole (2)
P020
254.0
The pitch of 20 sprocket holes
(in mm)
Continued on the following page.
31
104
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Packaging
Continued from the preceding page.
■ CERAFILr 4.5-6.5MHz Chip Type SFSKA Series
Dimensions of carrier tape
Dimensions of Reel
+0.1
–0.0
2.0±0.1 4.0±0.1
ø1.5
Leader
Cover film
Trailer
160-190
Empty Components
Empty
240-280 min.
2.2±0.5
400-560
+0.1
–0.0
Peeling strength
(0.1—0.7N)
4.3±0.1
ø1.5
8.0±0.1
Chip filter
3˚ max.
10˚ max.
Cover film
ø13.0±0.2
17.5±1.5
21.5±1.0
User direction of feed
• Part number marked side is always facing upside.
• The feeding holes side of cavity tape is always input terminal.
(in mm)
Continued on the following page.
31
105
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Packaging
Continued from the preceding page.
■ CERAFILr 4.5-6.5MHz Lead Type SFSRA Series
P2
P
dh dh
dS
M
M
D0
P1 F1 F2
P0
t
Direction Feed
Item
Code
L1
Dimensions
Tolerance
Remarks
Lead length under the hold down tape
Pitch of component
5.0 min.
12.7
-
P
±0.5
±0.2
±0.5
Tolerance for Pitches 10ZP0=127±1
Pitch of sprocket hole (1)
P0
P1
12.7
Length from hole center to lead
3.85
Length from hole center to
component center
P2
6.35
±0.5
Lead spacing (1)
F1
F2
2.5
2.5
±0.2
±0.2
±1.0
±0.5
-
Lead spacing (2)
Slant to the forward or backward
Width of carrier tape
dh
W
0
18.0
6.0 min.
9.0
Width of hold down tape
Position of Sprocket hole
Gap of hold down tape and carrier Tape
W0
W1
W2
±0.5
+0.5
–0
0
Hold down tape doesn't exceed the carrier tape.
Distance between the center of
sprocket hole and lead stopper
H0
18.0
±0.5
Diameter of sprocket hole
Total tape thickness
Pitch of sprocket hole (2)
Body tilt
D0
t
ø4.0
0.6
±0.2
±0.2
±1.5
±1.0
P020
dS
254.0
0
The pitch of 20 sprocket holes
(in mm)
Continued on the following page.
31
106
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Packaging
Continued from the preceding page.
■ CERAFILr 455kHz Chip Type PFWCC Series
Dimensions of Carrier Tape
Dimensions of Reel
4.0±0.1
2.0±0.1
ø1.55±0.1
Leader
Cover film
Trailer
160-190
Empty Components
Empty
240-280 min.
+0.5
-0.2
2.0
400-560
ø13.0±0.5
Peeling strength
(0.1—0.7N)
8.0±0.1
Chip filter
5.4±0.1
10˚ max.
3° max.
Cover film
+1
-0
12.5
User direction of feed
17.0±1
(in mm)
• Part number marked side is always facing upside.
• The feeding holes side of cavity tape is always input terminal.
■ CERAFILr 455kHz Chip Type SFPKA Series
Dimensions of Carrier Tape
Dimensions of Reel
Trailer
160-190
Leader
Cover film
4.0±0.1
+0.1
ø1.5 -0
2.0±0.1
Empty Components
Empty
240-280
ø13.0±0.2
400-560
2.2±0.5
12.0±0.1
5.3±0.1
User direction of feed
Cover film
Label
17.5±0.5
21.5±1.0
7.4±0.1
• Part number marked side is always facing upside.
• The feeding holes side of cavity tape is always input terminal.
(in mm)
Continued on the following page.
31
107
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Packaging
Continued from the preceding page.
■ CERAFILr 455kHz Lead Type PFSLF/PFWLF Series
dh dh
P2
P
dS1
D0
F1 F1
P1
F
t
P0
Item
Code
L1
Dimensions
3.0 min.
12.7
Tolerance
-
Remarks
Lead length under the hold down tape
Pitch of component
P
±0.5
±0.2
±0.5
Pitch of sprocket hole (1)
Length from hole center to lead
P0
P1
12.7
3.85
Length from hole center to
component center
P2
6.35
±0.5
W0.5
Y0.2
Lead spacing (1)
F
5.0
Lead spacing (2)
F1
2.5
±0.2
±1.0
±1.0
±0.5
-
Slant to the forward or backward
Slant to the left or right
Width of carrier tape
dh
0
dS1
W
0
18.0
6.0 min.
9.0
Width of hold down tape
Position of sprocket hole
Gap of hold down tape and carrier tape
W0
W1
W2
±0.5
W0.5
Y0.2
0
Hold-down tape doesn't exceed the carrier tape.
Distance between the center of
sprocket hole and lead stopper
H0
18.0
±0.5
Diameter of sprocket hole
Total tape thickness
D0
t
ø4.0
0.6
±0.2
±0.2
±1.5
Pitch of sprocket hole (2)
P020
254.0
The pitch of 20 sprocket holes
(in mm)
Continued on the following page.
31
108
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Packaging
Continued from the preceding page.
■ CERAFILr 455kHz Lead Type SFULA Series
Standard of Magazine Cassette
1. Putting CERAFILr into Magazine
3. Dimensions of Magazine Cassette
A magazine should contain 50pcs of CERAFILr, with the
marking of products all facing toward the "murata" mark
on a magazine, and be closed with exclusive stoppers at
both ends. Above should be the minimum packaging unit.
5.6±0.3
+0
–2
390
4.2±0.25
*
*
M
M
2. Quality of Magazine
(1) Transparent so that input / output direction is visually
recognizable.
1.1 1.1
(in mm)
Tolerance unless otherwise specified: ±0.2
(2) With an angle of 35° CERAFILr should slip down
smoothly.
Material: Polycarbonate
Camber of Case: ±1mm max. against entire length (reference)
Twist of Case: ±0.5mm max. (reference)
(3) Antistatic finish
(4) Recycling
Note: Magazines should be sent back for recycling.
(Therefore, empty magazines should not be damaged.)
■ CERAFILr 455kHz Lead Type SFZLA Series
Standard of Magazine Cassette
1. Putting CERAFILr into Magazine
3. Dimensions of Magazine Cassette
A magazine should contain 50pcs of CERAFILr, with the
marking of products all facing toward the "murata" mark
on a magazine, and be closed with exclusive stoppers at
both ends. Above should be the minimum packaging unit.
9.0±0.3
+0
–2
390
7.6±0.25
*
*
*
M
M
M
2. Quality of Magazine
1.1
1.1
(in mm)
Tolerance unless otherwise specified: ±0.2
(1) Transparent so that input / output direction is visually
recognizable.
Material: Polycarbonate
(2) With an angle of 35° CERAFILr should slip down
smoothly.
Camber of Case: ±1mm max. against entire length (reference)
Twist of Case: ±0.5mm max. (reference)
(3) Antistatic finish
(4) Recycling
Note: Magazines should be sent back for recycling.
(Therefore, empty magazines should not be damaged.)
■ CERAFILr 455kHz Lead Type SFPLA Series
Standard of Magazine Cassette
1. Putting CERAFILr into Magazine
3. Dimensions of Magazine Cassette
A magazine should contain 50pcs of CERAFILr, which
ground terminals are all facing toward the "murata" mark
on a magazine, and be closed with exclusive stoppers at
the both ends. Above should be the minimum packaging
unit.
9.0±0.3
405±1.0
7.6±0.25
HP51M0003-02
1.1 1.1
(in mm)
Tolerance unless otherwise specified: ±0.2
2. Quality of Magazine
(1) Transparent so that input / output direction is visually
recognizable.
Material: Polycarbonate
31
Camber of Case: ±1mm max. against entire length (reference)
Twist of Case: ±0.5mm max. (reference)
(2) With an angle of 35° CERAFILr should slip down
smoothly.
(3) Antistatic finish
(4) Recycling
Note: Magazines should be sent back for recycling.
(Therefore, empty magazines should not be damaged.)
Continued on the following page.
109
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Packaging
Continued from the preceding page.
■ CERAFILr 455kHz Lead Type CFWLA Series
Standard of Magazine Cassette
1. Putting CERAFILr into Magazine
4. Dimensions of Magazine Cassette
A magazine should contain 50pcs of CERAFILr, with
ground terminals all facing toward the "murata" mark on a
magazine, and be closed with exclusive stoppers at the
both ends. Above should be the minimum packaging unit.
9.0±0.3
7.3±0.25
576.0±2.0
ANTISTATIC
2. Quality of Magazine
muRataHP51M0064
(1) Transparent so that input / output direction is visually
recognizable.
5.3±0.3
0.6
(in mm)
Tolerance unless otherwise specified: ±0.2
(2) With an angle of 35° CERAFILr should slip down
smoothly.
Material: Polycarbonate
(3) Antistatic finish
Camber of Case: ±1mm max. against entire length (reference)
Twist of Case: ±0.5mm max. (reference)
(4) Recycling
Note: Magazines should be sent back for recycling.
(Therefore, empty magazines should not be damaged.)
3. Magazine should be packaged in a cardboard box.
MURATA model name, quantity and outgoing inspection
number should be indicated on the box.
Cardboard box may contain maximum 33 magazines
(1,650 pieces of filter).
■ Ceramic Trap 4.5-6.5MHz Chip Type TPSKA Series
Dimensions of carrier tape
Dimensions of Reel
+0.1
–0.0
2.0±0.1 4.0±0.1
ø1.5
Leader
Cover film
Trailer
160-190
Empty Components
Empty
240-280 min.
2.2±0.5
400-560
+0.1
–0.0
Peeling strength
(0.1—0.7N)
4.3±0.1
ø1.5
8.0±0.1
Chip filter
3˚ max.
10˚ max.
Cover film
ø13.0±0.2
17.5±1.5
21.5±1.0
User direction of feed
• Part number marked side is always facing upside.
• The feeding holes side of cavity tape is always input terminal.
(in mm)
Continued on the following page.
31
110
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Packaging
Continued from the preceding page.
■ Ceramic Trap 4.5-6.5MHz Chip Type TPWKA Series
Dimensions of carrier tape
Dimensions of Reel
+0.1
–0.0
ø1.5
2.0±0.1 4.0±0.1
Leader
Cover film
Trailer
160-190
Empty Components
Empty
240-280 min.
2.2±0.5
400-560
+0.1
–0.0
Peeling strength
(0.1—0.7N)
Chip filter
5.5±0.1
8.0±0.1
ø1.5
3˚ max.
10˚ max.
Cover film
ø13.0±0.2
17.5±1.5
21.5±1.0
User direction of feed
• Part number marked side is always facing upside.
• The feeding holes side of cavity tape is always input terminal.
(in mm)
Continued on the following page.
31
111
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Packaging
Continued from the preceding page.
■ Ceramic Trap 4.5-6.5MHz Lead Type TPSRA Series
P2
P
dh dh
dS
M
M
D0
P1 F1 F2
P0
t
Direction Feed
Item
Code
L1
Dimensions
Tolerance
Remarks
Lead length under the hold down tape
Pitch of component
5.0 min.
12.7
-
P
±0.5
±0.2
±0.5
Tolerance for Pitches 10ZP0=127±1
Pitch of sprocket hole (1)
P0
P1
12.7
Length from hole center to lead
3.85
Length from hole center to
component center
P2
6.35
±0.5
Lead spacing (1)
F1
F2
2.5
2.5
±0.2
±0.2
±1.0
±0.5
-
Lead spacing (2)
Slant to the forward or backward
Width of carrier tape
dh
W
0
18.0
6.0 min.
9.0
Width of hold down tape
Position of Sprocket hole
Gap of hold down tape and carrier Tape
W0
W1
W2
±0.5
+0.5
–0
0
Hold down tape doesn't exceed the carrier tape.
Distance between the center of
sprocket hole and lead stopper
H0
18.0
±0.5
Diameter of sprocket hole
Total tape thickness
Pitch of sprocket hole (2)
Body tilt
D0
t
ø4.0
0.6
±0.2
±0.2
±1.5
±1.0
P020
dS
254.0
0
The pitch of 20 sprocket holes
(in mm)
Continued on the following page.
31
112
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Packaging
Continued from the preceding page.
■ Ceramic Trap 3.5-6.5MHz Lead Type TPSRF_J Series
dh dh
P2
P
dS1
D0
P1
F
t
P0
Item
Code
L1
Dimensions
3.0 min.
12.7
Tolerance
-
Remarks
Lead length under the hold down tape
Pitch of component
P
±0.5
±0.2
±0.5
±0.5
Pitch of sprocket hole (1)
Length from hole center to lead
P0
P1
P2
12.7
3.85
Length from hole center to component center
6.35
+0.5
-0.2
Lead spacing
F
5.0
Slant to the forward or backward
Slant to the left or right
Width of carrier tape
dh
dS1
W
0
0
±1.0
±1.0
±0.5
-
18.0
6.0 min.
9.0
Width of hold down tape
Position of sprocket hole
W0
W1
±0.5
Gap of hold down tape and
carrier tape
+0.5
-0.0
W2
H0
0
Hold down tape doesn't exceed the carrier tape
Distance between the center of
sprocket hole and lead stopper
18.0
±0.5
Diameter of sprocket hole
Total tape thickness
D0
t
ø4.0
0.6
±0.2
±0.2
±1.5
Pitch of sprocket hole (2)
Po20
254.0
The pitch of 20 sprocket holes
(in mm)
Continued on the following page.
31
113
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Packaging
Continued from the preceding page.
■ Ceramic Trap 3.5-6.5MHz Lead Type TPSRF_W/TPWRF/TPTRF Series
dh dh
P2
P
dS1
F1 F1
D0
P1
F
t
P0
Item
Lead length under the hold down tape
Length of cut off
Code
L1
Dimensions
3.0 min.
2.0 max.
12.7
Tolerance
Remarks
-
L2
-
To distinguish the direction
Pitch of components
P
±0.5
±0.2
±0.5
±0.5
Pitch of sprocket hole (1)
Length from hole center to lead
P0
P1
P2
F
12.7
3.85
Length from hole center to component center
Lead spacing (1)
6.35
+0.5
5.0
–0.2
Lead spacing (2)
F1
2.5
±0.2
±1.0
±1.0
±0.5
-
Slant to the forward or backward
Slant to the left or right
dh
dS1
W
0
0
Width of carrier tape
18.0
Width of hold down tape
Position of sprocket hole
W0
W1
6.0 min.
9.0
±0.5
Hold down tape doesn't exceed
the carrier tape
+0.5
–0
Gap of hold down tape and carrier tape
W2
H0
0
Distance between the center of sprocket
hole and lead stopper
18.0
±0.5
Diameter of sprocket hole
Total tape thickness
D0
t
ø4.0
0.6
±0.2
±0.2
±1.5
Pitch of sprocket hole (2)
P020
254.0
The pitch of 20 sprocket holes
(in mm)
Continued on the following page.
31
114
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Packaging
Continued from the preceding page.
■ Ceramic Discriminator 10.7MHz Chip Type CDSCB Series
Dimensions of Carrier Tape
Dimension of reel
Trailer
160-190
Leader
Cover film
4.0±0.1
+0.1
ø1.5
-0
2.0±0.05
Empty Components
Empty
240-280
ø13.0±0.2
400-560
+0.1
2.0±0.5
4.0±0.1
ø1.5
-0
2.2±0.1
Peeling strength
0.1 to 0.7N
3˚max.
Cover film
+1.0
10˚
13.0
-0
17.0±1.0
User direction of feed
· Part number marked side is always facing upside.
· The feeding holes side of cavity tape is always input terminal.
(
) : Reference
(in mm)
Continued on the following page.
31
115
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Packaging
Continued from the preceding page.
■ Ceramic Discriminator 10.7MHz Lead Type CDALF Series
dh dh
P2
P
dS1
D0
P1
F
t
P0
Item
Code
L1
Dimensions
3.0 min.
12.7
Tolerance
-
Remarks
Lead length under the hold down tape
Pitch of component
P
±0.5
±0.2
±0.5
±0.5
Pitch of sprocket hole (1)
Length from hole center to lead
P0
P1
P2
12.7
3.85
Length from hole center to component center
6.35
+0.5
-0.2
Lead spacing
F
5.0
Slant to the forward or backward
Slant to the left or right
Width of carrier tape
dh
dS1
W
0
0
±1.0
±1.0
±0.5
-
18.0
6.0 min.
9.0
Width of hold down tape
Position of sprocket hole
W0
W1
±0.5
Gap of hold down tape and
carrier tape
+0.5
-0.0
W2
H0
0
Hold down tape doesn't exceed the carrier tape
Distance between the center of
sprocket hole and lead stopper
18.0
±0.5
Diameter of sprocket hole
Total tape thickness
D0
t
ø4.0
0.6
±0.2
±0.2
±1.5
Pitch of sprocket hole (2)
Po20
254.0
The pitch of 20 sprocket holes
(in mm)
Continued on the following page.
31
116
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Packaging
Continued from the preceding page.
■ Ceramic Discriminator 3.5-6.5MHz CDSRF_EK Series
dh dh
P2
P
dS1
D0
P1
F
t
P0
Item
Code
L1
Dimensions
3.0 min.
12.7
Tolerance
-
Remarks
Lead length under the hold down tape
Pitch of component
P
±0.5
±0.2
±0.5
±0.5
Pitch of sprocket hole (1)
Length from hole center to lead
P0
P1
P2
12.7
3.85
Length from hole center to component center
6.35
+0.5
-0.2
Lead spacing
F
5.0
Slant to the forward or backward
Slant to the left or right
Width of carrier tape
dh
dS1
W
0
0
±1.0
±1.0
±0.5
-
18.0
6.0 min.
9.0
Width of hold down tape
Position of sprocket hole
W0
W1
±0.5
Gap of hold down tape and
carrier tape
+0.5
-0.0
W2
H0
0
Hold down tape doesn't exceed the carrier tape
Distance between the center of
sprocket hole and lead stopper
18.0
±0.5
Diameter of sprocket hole
Total tape thickness
D0
t
ø4.0
0.6
±0.2
±0.2
±1.5
Pitch of sprocket hole (2)
Po20
254.0
The pitch of 20 sprocket holes
(in mm)
Continued on the following page.
31
117
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Packaging
Continued from the preceding page.
■ Ceramic Discriminator 3.5-6.5MHz CDSRF_CK Series
dh dh
P2
P
dS1
F1 F1
D0
P1
F
t
P0
Item
Lead length under the hold down tape
Length of cut off
Code
L1
Dimensions
3.0 min.
2.0 max.
12.7
Tolerance
Remarks
-
L2
-
To distinguish the direction
Pitch of components
P
±0.5
±0.2
±0.5
±0.5
Pitch of sprocket hole (1)
Length from hole center to lead
P0
P1
P2
F
12.7
3.85
Length from hole center to component center
Lead spacing (1)
6.35
+0.5
5.0
–0.2
Lead spacing (2)
F1
2.5
±0.2
±1.0
±1.0
±0.5
-
Slant to the forward or backward
Slant to the left or right
dh
dS1
W
0
0
Width of carrier tape
18.0
Width of hold down tape
Position of sprocket hole
W0
W1
6.0 min.
9.0
±0.5
Hold down tape doesn't exceed
the carrier tape
+0.5
–0
Gap of hold down tape and carrier tape
W2
H0
0
Distance between the center of sprocket
hole and lead stopper
18.0
±0.5
Diameter of sprocket hole
Total tape thickness
D0
t
ø4.0
0.6
±0.2
±0.2
±1.5
Pitch of sprocket hole (2)
P020
254.0
The pitch of 20 sprocket holes
(in mm)
31
118
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
!Note
P50E1.pdf 05.3.30
Note:
1. Export Control
For customers outside Japan
<
>
Murata products should not be used or sold for use in the development, production, stockpiling or utilization of any conventional weapons or mass-destructive
weapons (nuclear weapons, chemical or biological weapons, or missiles), or any other weapons.
For customers in Japan
<
>
For products which are controlled items subject to the “Foreign Exchange and Foreign Trade Law” of Japan, the export license specified by the law is required
for export.
2. Please contact our sales representatives or product engineers before using the products in this catalog for the applications listed below, which require especially
high reliability for the prevention of defects which might directly damage to a third party's life, body or property, or when one of our products is intended for use
in applications other than those specified in this catalog.
q Aircraft equipment
w Aerospace equipment
e Undersea equipment
t Medical equipment
u Traffic signal equipment
o Data-processing equipment
r Power plant equipment
y Transportation equipment (vehicles, trains, ships, etc.)
i Disaster prevention / crime prevention equipment
! Application of similar complexity and/or reliability requirements to the applications listed in the above
3. Product specifications in this catalog are as of November 2004. They are subject to change or our products in it may be discontinued without advance notice.
Please check with our sales representatives or product engineers before ordering. If there are any questions, please contact our sales representatives or
product engineers.
4. Please read rating and
CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
5. This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or
transact the approval sheet for product specifications before ordering.
6. Please note that unless otherwise specified, we shall assume no responsibility whatsoever for any conflict or dispute that may occur in connection with the effect
of our and/or a third party's intellectual property rights and other related rights in consideration of your use of our products and/or information described or
contained in our catalogs. In this connection, no representation shall be made to the effect that any third parties are authorized to use the rights mentioned
above under licenses without our consent.
7. No ozone depleting substances (ODS) under the Montreal Protocol are used in our manufacturing process.
http://www.murata.com/
He a d O ffice
In te rn a tio n a l Divisio n
1-10-1, Higashi Kotari, Nagaokakyo-shi, Kyoto 617-8555, Japan
Phone: 81-75-951-9111
3-29-12, Shibuya, Shibuya-ku, Tokyo 150-0002, Japan
Phone: 81-3-5469-6123 Fax: 81-3-5469-6155 E-mail: intl@murata.co.jp
相关型号:
©2020 ICPDF网 联系我们和版权申明