TF037E-2000-F [NIDEC]
Blowers Outline;
| 型号： | TF037E-2000-F |
| 厂家： | 
NIDEC COMPONENTS |
| 描述： | Blowers Outline |
| 文件： | 总8页 (文件大小：254K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
NIDEC COPAL ELECTRONICS CORP.
1
7
/
Model No. TF037E-2000-F
Specifications
Issuing Date
Aug.1, 2017
１．Scope
This specification applies to Blower TF037E-2000-F (hereinafter referred to as "the PRODUCT"),
a product of NIDEC COPAL ELECTRONICS CORP. (hereinafter referred to as "NCEL").
Driving circuit : NCEL's standard driving circuit
２．Specification
(Note1) Unless otherwise specified, the environmental conditions are 23℃±5℃，normal humidity,
and atmospheric pressure range 90 to 106kPa.
(Note2) Measuring conditions :
Driving circuit = NCEL's standard driving circuit,
Supply voltage = DC24V, measurement equipment = NCEL's standard equipment
(Note3)
The below specifications specify the characteristics of the Blowers at the time of shipment.
The characteristics may change over time depending on the usage conditions and
environment.
(Note4) Please contact us if you'd like to operate the PRODUCT outside of specifications.
(Note5) The specification value is measured under the plate by the vertical position to axis.
No.
1
Items
Specification
Remarks
Rated Voltage
DC 24 V±10%
Direction of
Rotation
Looking down from the air
inlet.
2
CCW (Counter-Clockwise)
Air
3
Kind of Gas
Configuration
Type of Motor
Noncorrosive gas
4
Motor with Centrifugal Blade
DC Brushless Motor
Without driving circuit
5
6
Number of Poles 8 Poles (4 pole pairs)
7
Drive System
Bearings
Impeller
3 Phase, Bipolar
8
Aero-Dynamic Bearings
Centrifugal Turbo Blade
Drawing ︓ 6404-00655-00
9
Please refer to attached
drawing.
10
Outline
No vibration, shock, or
gyration is to be applied during
operation.
Mounting
Direction
Shaft vertical to ground, air inlet facing
upwards.(±5°)
11
NIDEC COPAL ELECTRONICS CORP.
Specification
2
7
/
No.
12
Items
Remarks
Max. Input Coil
Current
3.0 A rms
Excluding inrush current.
max.
Rated Power
Supply Current
Rated Power
Consumption
13
14
15
0.86 A
max.
at 3.0kPa, 100L/min, DC 24V
at 3.0kPa, 100L/min, DC 24V
at 3.0kPa
22.7 W max.
100 L/min
Rated Air Flow
16 Minimum Air Flow 10 L/min
17 Rated Pressure 3.0 kPa
Maximum
at 100L/min
18
19
20
4.5 kPa
Absolute maximum pressure
at 3.0kPa, 100L/min
Pressure
Rated Rotation
Speed
35,500 r/min (reference value)
6,000 r/min
Min．Rotation
Speed
Pressure-air flow must be
within the "area of use"
specified in "5. Operating
Range" on P.5.
Max．Rotation
Speed
21
45,000 r/min
22 Torque Constant 0.0020〜0.0026 N･m/A (reference value)
at 3.0kPa, 100L/min.
Acoustic Audible
Measured at 1m from air inlet.
Include background noise
15dB(A).
23
65.0 dB(A )max.
0.36〜0.66
Noise
24 Coil Resistance
(reference value)
at 20℃ （Between 2 phase)
ohm
at 20℃, 10kHz
(Between 2 phase)
25 Coil Inductance 17〜23 μH
26 Insulation Class Class E
Insulation
(reference value)
JIS C 4003
DC500V,between terminal pins
and plate
JIS C 4003
min.
ohm
27
20M
Resistance
AC600V for 1sec. between
terminal pins and Plate.
JIS C 4003
Dielectric
Strength
28
Leak current to be less than 1mA.
165 g (reference value）
29
30
Weight
19 g･cm2
Rotor Inertia
(reference value）
Max. allowable force to the
intake (upper housing) in axial
direction.
Max. Axial
Loading
31
3N
max.
NIDEC COPAL ELECTRONICS CORP.
Specification
3
7
/
No.
32
33
34
35
Items
Remarks
Operating
Temperature
-10 to 60℃
Range
Operating
10 to 90%RH
-20 to 60℃
No condensation
No condensation
Humidity Range
Storage
Temperature
Range
Storage
10 to 90%RH
Humidity Range
The Blower shall satisfy Specification
No.12 〜 28 after the following test.
Kind of
Vibration
Sweep
@ amplitude
10〜22Hz
Resistance to
Vibration
Frequency
Range
1mm
36
Non-operating
@ acceleration
22〜50Hz
19.6m/s2 (2G)
Sweep
To-and-fro, approx. 5min.
X, Y, Z directions, 60min.
each
Test Time
The Blower shall satisfy Specification
No.12 〜 28 after the following test.
294m/s2（30G）
Acceleration
Resistance to
Shock
Pulse Width
6ms
37
Non-operating
Shock
Wave
Semi-sinusoidal wave
Number of X, Y, Z, directions, once per
Shock each direction
NIDEC COPAL ELECTRONICS CORP.
4
7
/
３．Interface
Pin No.
1
Symbol
Signal
Air Inlet
Hall Element Power Supply
(+12V)
Vcc
2
3
4
5
6
7
H2-
H2+
H3-
Hall Element 2 Output
Hall Element 3 Output
Hall Element 1 Output
GND
1
12
H3+
H1-
Manufacturer J.S.T. Mfg. Co. Ltd.
H1+
Part No.
ꢀSM12B-PASS
8
GND
TH
V
Thermistor Output
Motor Coil (V)
9
【Mating Connector】
Manufacturer J.S.T. Mfg. Co., Ltd.
10
(insulation displacement
connector)
ꢀ（retainer︓PAFS-12V-S）
ꢀ12PAF-6S
Motor Coil (W)
Motor Coil (U)
11
12
W
U
Part No.
(crimp type)
ꢀPAP-12V-S
(Note7) Parts used for thermistor output;
ꢀ（contact︓SPHD-001T-P0.5）
Manufacturer
Part No.
:
TDK Corp.
: NTCG164BH103JT
(Note6) Either IDC or crimp type can be used as a
mating connector.
(Note8) Parts used for hall element output;
Manufacturer
Part No.
: Asahi Kasei EMD Corp.
: HW-105A
４．Timing Chart
H
H1+
L
H
H1-
L
H
H2+
L
H
H2-
L
H
H3+
L
H
H3-
L
+
U
-
+
V
-
+
W
-
0
60 120 180 240 300 360
15 30 45 60 75 90
[deg] Electrical degree
[deg] Mechanical degree
0
NIDEC COPAL ELECTRONICS CORP.
5
7
/
５． Operating Range
(Note 9) The following graph is provided for reference only. Values are not guaranteed.
(Note 10) Supply Voltage : DC 24 V, Environmental conditions : 23℃, Atmospheric pressure : 101.3kPa
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
1.2
1.0
0.8
0.6
0.4
0.2
0.0
Operating Range
40,000rpm
30,000rpm
15,000rpm
Current＠40,000r/min
Current＠30,000r/min
Current＠15,000r/min
0
20
40
60
80
100
120
140
Air Flow [L/min]
６．Manufacturing Code
QRꢀCode
Model No.，Lot No.(year of manufacture，month of manufacture，
day of manufacture，control number)，Serial Number
:
Serial Number
Control number
alphabet (A - Z)
:
Date of manufacture refer to Chart 1 below
:
Month of manufactur refer to Chart 2 below
:
Year of manufacture
last digit of the year (A.D.)
:
【Chart 1】
Date
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9 10 11 12 13 14 15 16 17 18 19 20
Code
1
9
A
B
C
D
E
F
G
H
J
K
L
Date
Code
21 22 23 24 25 26 27 28 29 30 31
M
N
P
Q
R
T
U
V
W
X
Y
【Chart 2】
Month
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9 10 11 12
Code
1
9
O
N
D
NIDEC COPAL ELECTRONICS CORP.
6
7
/
７．Warranty
ꢀ７-１．Warranty Period
Warranty period of the PRODUCT is 1 year from delivery.
ꢀ７-２．Warranty Scope
In case a defect is found in the PRODUCT during the above warranty period and NCEL is responsible for the defect,
NCEL will either repair or replace the defected PRODUCT free of charge.
(1)
However, in the following cases, the PRODUCT will not be covered by warranty.
Defects caused by inappropriate conditions, environments, handlings, and use which are not specified in this
specification.
Defects caused by your equipments and/or software.
Defects caused by modifications and/or repairs which were not done by NCEL.
Defects which could have been avoided if the PRODUCT was used accordingly to this specification.
Defects which were unpredictable with the scientific or technical level of NCEL at the time of shipment.
Defects caused by external factors such as natural hazards (fire, earthquakes, floods) or electrical surges.
NCEL will be responsible for the PRODUCT only in which the coverage will be limited to Clause 7-2. (1). NCEL shall
not be liable for customer's equipment damages, opportunity losses, or lost earnings caused by defects of the
(2)
PRODUCTS. The user shall indemnify NCEL and hold NCEL harmless from any liability or damage whatsoever arising
out of any action not in accordance with this specification.
ꢀ７-３．Product Application
The PRODUCT is designed and manufactured for general industrial use for general purposes. Please do not use in
applications such as nuclear power, aviations, railroads, or medical equipment where great effect to human lives or
wealth are expected.
However, if NCEL agree with the customer the usage of the PRODUCT in such applications, NCEL will warrant the
PRODUCT in the same scope described in "7. Warranty" in this specification.
８．Notes
(1) All values are measured with NCEL's standard equipments unless otherwise specified.
(2) The PRODUCT is compliant with RoHS directives which went into effect July, 2011.
Designated hazardous substances are lead, mercury, cadmium, hexavalent chrome, brominated flame retardants
(PBB, PBDE) and its compounds.
(3) The PRODUCT is compliant with Directive 2006/122/EC of the European Parliament (Council Directive 76/769/EEC
（30th amendment)) which restricts the use of PFOS.
(4) Contents of this document may be changed without notice. The production of the PRODUCT may be discontinued
without notice. Please confirm with your local contact before ordering.
(5) Please check if the PRODUCT operates normally at every start-up and during operation.
(6) Please provide safety measures to prevent damages in case of product failures.
(7) Performance cannot be guaranteed in case the PRODUCT is used beyond the specification or the PRODUCT is
(8) Depending on the conditions or the environment, functions or performances of the PRODUCT may not be satisfied
when the PRODUCT is used with other equipments.
(9) Please do not use the PRODUCT in applications to protect the body.
(10)
(11)
(12)
(13)
Please protect the PRODUCT from condensation.
Please use the correct supply voltage to operate the PRODUCT.
Do not disassemble or modify the PRODUCT.
Turn off the power immediately and stop using the PRODUCT in the following cases.
● In case water or foreign substances get into the PRODUCT.
● In case the PRODUCT is dropped or the housing is broken.
● In case unusual odor, abnormal noise, or smoke are generated from the PRODUCT.
Turn off the power of the PRODUCT and any equipment attached to the PRODUCT when putting on or taking off the
cables.
(14)
NIDEC COPAL ELECTRONICS CORP.
7
7
/
(15)
Do not use or store in the following conditions;
● Humid, dusty, or poorly-ventilated area.
● Areas where the temperature is expected to rise (direct sunlight, etc.).
● Areas with corrosive gas or flammable gas in the surrounding air.
● Areas where vibration, shock, or rocking motion is applied directly to the PRODUCT.
● Areas where the PRODUCTS may be splashed with water, oil, or chemicals.
● Areas where static electricity can be built up.
(16)
(17)
Please contact us if you have any questions regarding installation.
Do not block the air inlet and outlet (2 places). Please contact us if you have any questions regarding the air inlet
and outlet.
(18)
Vibration or audible noise level may change over time due to contamination of the blade. Please provide dust-proof
constructions around the PRODUCT.
(19)
(20)
(21)
Please advise us in case the driving circuit will be designed at the customer's side.
Please connect and don't use air inlet of this product (2 places) in series.
Please don't use by the suction use.
相关型号：
©2020 ICPDF网 联系我们和版权申明