DS90CR481VJD/NOPB [NSC]
IC SPECIALTY INTERFACE CIRCUIT, PQFP100, TQFP-100, Interface IC:Other;
| 型号： | DS90CR481VJD/NOPB |
| 厂家： | 
National Semiconductor |
| 描述： | IC SPECIALTY INTERFACE CIRCUIT, PQFP100, TQFP-100, Interface IC:Other 接口集成电路 |
| 文件： | 总21页 (文件大小：889K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
January 2006
DS90CR481 / DS90CR482
48-Bit LVDS Channel Link SER/DES − 65 - 112 MHz
enhancement. To increase bandwidth, the maximum clock
rate is increased to 112 MHz and 8 serialized LVDS outputs
are provided. Cable drive is enhanced with a user selectable
pre-emphasis feature that provides additional output current
during transitions to counteract cable loading effects. Op-
tional DC balancing on a cycle-to-cycle basis, is also pro-
vided to reduce ISI (Inter-Symbol Interference). With pre-
emphasis and DC balancing, a low distortion eye-pattern is
provided at the receiver end of the cable. A cable deskew
capability has been added to deskew long cables of pair-to-
pair skew of up to +/−1 LVDS data bit time (up to 80 MHz
Clock Rate). These three enhancements allow cables 5+
meters in length to be driven.
General Description
The DS90CR481 transmitter converts 48 bits of CMOS/TTL
data into eight LVDS (Low Voltage Differential Signaling)
data streams. A phase-locked transmit clock is transmitted in
parallel with the data streams over a ninth LVDS link. Every
cycle of the transmit clock 48 bits of input data are sampled
and transmitted. The DS90CR482 receiver converts the
LVDS data streams back into 48 bits of LVCMOS/TTL data.
At a transmit clock frequency of 112MHz, 48 bits of TTL data
are transmitted at a rate of 672Mbps per LVDS data channel.
Using a 112MHz clock, the data throughput is 5.38Gbit/s
(672Mbytes/s). At a transmit clock frequency of 112MHz, 48
bits of TTL data are transmitted at a rate of 672Mbps per
LVDS data channel. Using a 66MHz clock, the data through-
put is 3.168Gbit/s (396Mbytes/s).
The chipset is an ideal means to solve EMI and cable size
problems associated with wide, high speed TTL interfaces.
The multiplexing of data lines provides a substantial cable
reduction. Long distance parallel single-ended buses typi-
cally require a ground wire per active signal (and have very
limited noise rejection capability). Thus, for a 48-bit wide
data and one clock, up to 98 conductors are required. With
this Channel Link chipset as few as 19 conductors (8 data
pairs, 1 clock pair and a minimum of one ground) are
needed. This provides an 80% reduction in cable width,
which provides a system cost savings, reduces connector
physical size and cost, and reduces shielding requirements
due to the cables’ smaller form factor.
Features
n 3.168 Gbits/sec bandwidth with 66 MHz Clock
n 5.376 Gbits/sec bandwidth with 112 MHz Clock
n 65 - 112 MHz input clock support
n LVDS SER/DES reduces cable and connector size
n Pre-emphasis reduces cable loading effects
n Optional DC balance encoding reduces ISI distortion
n Cable Deskew of +/−1 LVDS data bit time (up to 80
MHz Clock Rate)
n 5V Tolerant TxIN and control input pins
n Flow through pinout for easy PCB design
n +3.3V supply voltage
The 48 CMOS/TTL inputs can support a variety of signal
combinations. For example, 6 8-bit words or 5 9-bit (byte +
parity) and 3 controls.
n Transmitter rejects cycle-to-cycle jitter
n Conforms to ANSI/TIA/EIA-644-1995 LVDS Standard
The DS90CR481/DS90CR482 chipset is improved over prior
generations of Channel Link devices and offers higher band-
width support and longer cable drive with three areas of
Generalized Block Diagrams (DS90CR481 and DS90CR482)
20009101
© 2006 National Semiconductor Corporation
DS200091
www.national.com
Generalized Transmitter Block Diagram – DS90CR481
20009102
Generalized Receiver Block Diagram – DS90CR482
20009103
Ordering Information
Order Number
DS90CR481VJD
DS90CR482VS
Function
Package
VJD100A
VJD100A
Transmitter (Serializer)
Receiver (Deserializer)
www.national.com
2
Absolute Maximum Ratings (Note 1)
DS90CR482VS
Package Derating:
DS90CR481VJD
DS90CR482VS
ESD Rating:
2.3W
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
18.1mW/˚C above +25˚C
18.1mW/˚C above +25˚C
Supply Voltage (VCC
)
−0.3V to +4V
CMOS/TTL Input Voltage
LVCMOS/TTL Output
Voltage
−0.3V to +5.5V
DS90CR481
>
(HBM, 1.5kΩ, 100pF)
(EIAJ, 0Ω, 200pF)
DS90CR482
6 kV
−0.3V to (VCC + 0.3V)
−0.3V to +3.6V
>
300 V
LVDS Receiver Input
Voltage
>
(HBM, 1.5kΩ, 100pF)
(EIAJ, 0Ω, 200pF)
2 kV
LVDS Driver Output
Voltage
>
200 V
−0.3V to +3.6V
LVDS Output Short
Circuit Duration
Recommended Operating
Conditions
Continuous
+150˚C
Junction Temperature
Storage Temperature
Lead Temperature
(Soldering, 4 sec.)
100L TQFP
−65˚C to +150˚C
Min Nom Max Units
Supply Voltage (VCC
Operating Free Air
Temperature (TA)
)
3.0
3.3
3.6
V
+260˚C
−10 +25 +70
˚C
@
Maximum Package Power Dissipation Capacity
25˚C
Supply Noise Voltage
Input Clock (TX)
100 mVp-p
112 MHz
65
100 TQFP Package:
DS90CR481VJD
2.3W
Electrical Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol
Parameter
Conditions
Min
2.0
Typ
Max
0.8
Units
CMOS/TTL DC SPECIFICATIONS
VIH
VIL
High Level Input
Voltage
V
V
Low Level Input
Voltage
GND
VOH
VOL
High Level Output
Voltage
IOH = −0.4 mA
IOH = −2mA
IOL = 2 mA
2.7
2.7
2.9
2.85
0.1
V
V
V
Low Level Output
Voltage
0.3
VCL
IIN
Input Clamp Voltage
Input Current
ICL = −18 mA
−0.79
+1.8
0
−1.5
+15
V
VIN = 0.4V, 2.5V or VCC
VIN = GND
µA
µA
mA
−15
250
IOS
Output Short Circuit
Current
VOUT = 0V
−120
LVDS DRIVER DC SPECIFICATIONS
|VOD
|
Differential Output
Voltage
RL = 100Ω
345
450
35
mV
mV
∆VOD
Change in VOD
between
Complimentary Output
States
VOS
Offset Voltage
Change in VOS
between
1.125
1.25
1.375
35
V
∆VOS
mV
Complimentary Output
States
3
www.national.com
Electrical Characteristics (Continued)
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol
IOS
Parameter
Output Short Circuit
Current
Conditions
VOUT = 0V, RL = 100Ω
Min
Typ
Max
Units
−3.5
−5
mA
IOZ
Output TRI-STATE
Current
PD = 0V, VOUT = 0V or VCC
1
10
µA
LVDS RECEIVER DC SPECIFICATIONS
VTH
VTL
IIN
Differential Input High
Threshold
VCM = +1.2V
+100
mV
mV
Differential Input Low
Threshold
−100
Input Current
VIN = +2.4V, VCC = 3.6V
VIN = 0V, VCC = 3.6V
10
10
µA
µA
TRANSMITTER SUPPLY CURRENT
ICCTW
Transmitter Supply
Current
RL = 100Ω, CL = 5 pF,
BAL = High,
f = 66MHz
106
155
5
160
210
50
mA
mA
µA
Worst Case
Worst Case Pattern
(Figures 1, 2)
f = 112MHz
ICCTZ
Transmitter Supply
Current
PD = Low
Driver Outputs in TRI-STATE during power down
Mode
Power Down
RECEIVER SUPPLY CURRENT
ICCRW
Receiver Supply
Current
CL = 8 pF, BAL = High,
Worst Case Pattern
(Figures 1, 3)
f = 66MHz
200
250
20
210
280
100
mA
mA
µA
f = 112MHz
Worst Case
Receiver Supply
Current
ICCRZ
PD = Low
Receiver Outputs stay low during power down
mode.
Power Down
Recommended Transmitter Input Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol
TCIT
Parameter
TxCLK IN Transition Time (Figure 4)
TxCLK IN Period (Figure 5)
TxCLK in High Time (Figure 5)
TxCLK in Low Time (Figure 5)
TxIN Transition Time
Min
1.0
Typ
Max
Units
ns
2.0
3.0
TCIP
8.93
0.35T
0.35T
1.5
15.38
0.65T
0.65T
6.0
ns
TCIH
TCIL
0.5T
0.5T
ns
ns
TXIT
ns
www.national.com
4
Transmitter Switching Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol
Parameter
LVDS Low-to-High Transition Time, (Figure 2),
PRE = 0.75V (disabled)
Min
Typ
Max
Units
LLHT
0.14
0.7
ns
LVDS Low-to-High Transition Time, (Figure 2),
PRE = Vcc (max)
0.11
0.16
0.6
0.8
0.7
ns
ns
ns
ns
ps
LHLT
LVDS High-to-Low Transition Time, (Figure 2),
PRE = 0.75V (disabled)
LVDS High-to-Low Transition Time, (Figure 2),
PRE = Vcc (max)
0.11
TBIT
Transmitter Bit Width
f = 66 MHz,
1/7 TCIP
0
112MHz
f = 65 to 112
MHz
TPPOS
Transmitter Pulse Positions -
Normalized
− 200
+200
TJCC
TCCS
TSTC
THTC
TPDL
TPLLS
TPDD
Tranmitter Jitter - Cycle-to-Cycle
TxOUT Channel to Channel Skew
TxIN Setup to TxCLK IN, (Figure 5)
TxIN Hold to TxCLK IN, (Figure 5)
100
40
ps
ps
ns
ns
ns
ms
ns
2.5
0
Transmitter Propagation Delay - Latency, (Figure 7)
Transmitter Phase Lock Loop Set, (Figure 9)
Transmitter Powerdown Delay, (Figure 11)
1.5(TCIP)+3.72 1.5(TCIP)+4.4 1.5(TCIP)+6.24
10
100
Receiver Switching Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol
Parameter
CMOS/TTL Low-to-High Transition Time, Rx data out,
(Figure 3)
Min
Typ
Max
Units
CLHT
2.0
ns
CMOS/TTL Low-to-High Transition Time, Rx clock
out, (Figure 3)
1.0
2.0
ns
ns
ns
CHLT
CMOS/TTL High-to-Low Transition Time, Rx data out,
(Figure 3)
CMOS/TTL High-to-Low Transition Time, Rx clock
out, (Figure 3)
1.0
RCOP
RCOH
RxCLK OUT Period, (Figure 6)
RxCLK OUT High Time, (Figure 6), f = 112 MHz
8.928
T
15.38
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ms
µs
3.5
(Note 4)
f = 66 MHz
f = 112 MHz
f = 66 MHz
f = 112 MHz
f = 66 MHz
f = 112 MHz
f = 66 MHz
6.0
RCOL
RSRC
RHRC
RxCLK OUT Low Time, (Figure 6),
3.5
(Note 4)
6.0
2.4
RxOUT Setup to RxCLK
OUT,(Figure 6)
3.6
RxOUT Hold to RxCLK OUT,
3.4
(Figure 6), (Note 4)
6.0
RPDL
RPLLS
RPDD
Receiver Propagation Delay - Latency, (Figure 8)
Receiver Phase Lock Loop Set, (Figure 10)
Receiver Powerdown Delay, (Figure 12)
3(TCIP)+4.0
3(TCIP)+4.8
3(TCIP)+6.5
10
1
5
www.national.com
Chipset RSKM Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified.(Notes 4, 7). See Applications Infor-
mation section for more details on this parameter and how to apply it.
Symbol
Parameter
Receiver Skew Margin without
Deskew in non-DC Balance Mode,
(Figure 13), (Note 5)
Min
170
Typ
Max
Units
ps
RSKM
f = 112 MHz
f = 100 MHz
f = 85MHz
170
240
350
350
ps
300
ps
f = 66MHz
300
ps
RSKM
Receiver Skew Margin without
Deskew in DC Balance Mode,
(Figure 13), (Note 5)
f = 112 MHz
f = 100 MHz
f = 85 MHz
f = 66 MHz
170
ps
170
200
300
300
ps
250
ps
250
ps
RSKMD
Receiver Skew Margin with Deskew f = 33 to 80
0.25TBIT
ps
in DC Balance, (Figure 14),
(Note 6)
MHz
RDR
Receiver Deskew Range
Receiver Deskew Step Size
f = 80 MHz
f = 80 MHz
1
TBIT
ns
RDSS
0.3 TBIT
Note 1: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device
should be operated at these limits. The tables of “Electrical Characteristics” specify conditions for device operation.
Note 2: Typical values are given for V
= 3.3V and T = +25˚C.
A
CC
Note 3: Current into device pins is defined as positive. Current out of device pins is defined as negative. Voltages are referenced to ground unless otherwise
specified (except V , V , V and ∆V ).
TH
TL
OD
OD
Note 4: The Minimum and Maximum Limits are based on statistical analysis of the device performance over voltage and temperature ranges. This parameter is
functionally tested on Automatic Test Equipment (ATE). ATE is limited to 85MHz. A sample of characterization parts have been bench tested to verify functional
performance.
Note 5: Receiver Skew Margin (RSKM) is defined as the valid data sampling region at the receiver inputs. This margin takes into account transmitter output pulse
positions (min and max) and the receiver input setup and hold time (internal data sampling window, RSPOS). This margin allows for LVDS interconnect skew,
inter-symbol interference (both dependent on type/length of cable) and clock jitter (TJCC).
RSKM ≥ cable skew (type, length) + source clock jitter (cycle to cycle,TJCC) + ISI (if any). See Applications Information section for more details.
Note 6: Receiver Skew Margin with Deskew (RSKMD) is defined as the valid data sampling region at the receiver inputs. The DESKEW function will constrain the
receiver’s sampling strobes to the middle half of the LVDS bit and removes (adjusts for) fixed interconnect skew. This margin (RSKMD) allows for inter-symbol
interference (dependent on type/length of cable), Transmitter Pulse Position (TPPOS) variance, and LVDS clock jitter (TJCC).
RSKMD ≥ ISI + TPPOS(variance) + source clock jitter (cycle to cycle, TJCC). See Applications Information section for more details.
Note 7: Typical values for RSKM and RSKMD are applicable for fixed V and T of the Transmitter and Receiver (both are assumed to be at the same V and
CC
A
CC
T
points).
A
www.national.com
6
AC Timing Diagrams
20009110
FIGURE 1. “Worst Case” Test Pattern
Note 8: The worst case test pattern produces a maximum toggling of digital circuits, LVDS I/O and CMOS/TTL I/O.
20009112
FIGURE 2. DS90CR481 (Transmitter) LVDS Output Load and Transition Times
20009130
FIGURE 3. DS90CR482 (Receiver) CMOS/TTL Output Load and Transition Times
20009114
FIGURE 4. DS90CR481 (Transmitter) Input Clock Transition Time
7
www.national.com
AC Timing Diagrams (Continued)
20009115
FIGURE 5. DS90CR481 (Transmitter) Setup/Hold and High/Low Times
20009131
FIGURE 6. DS90CR482 (Receiver) Setup/Hold and High/Low Times
20009127
FIGURE 7. DS90CR481 (Transmitter) Propagation Delay - Latency
www.national.com
8
AC Timing Diagrams (Continued)
20009132
FIGURE 8. DS90CR482 (Receiver) Propagation Delay - Latency
20009119
FIGURE 9. DS90CR481 (Transmitter) Phase Lock Loop Set Time
20009133
FIGURE 10. DS90CR482 (Receiver) Phase Lock Loop Set Time
9
www.national.com
AC Timing Diagrams (Continued)
20009121
FIGURE 11. DS90CR481 (Transmitter) Power Down Delay
20009134
FIGURE 12. DS90CR482 (Receiver) Power Down Delay
www.national.com
10
AC Timing Diagrams (Continued)
20009125
C — Setup and Hold Time (Internal data sampling window) defined by Rspos (receiver input strobe position) min and max
Tppos — Transmitter output pulse position (min and max)
RSKM ≥ Cable Skew (type, length) + LVDS Source Clock Jitter (cycle to cycle) + ISI (Inter-symbol interference)
j
j
j
Cable Skew — typically 10 ps–40 ps per foot, media dependent
Cycle-to-cycle LVDS Output jitter (TJCC) is less than 100 ps (worse case estimate).
ISI is dependent on interconnect length; may be zero
See Applications Information section for more details.
FIGURE 13. Receiver Skew Margin (RSKM) for Chipset without DESKEW
20009137
C — Setup and Hold Time (Internal data sampling window) defined by Rspos (receiver input strobe position) min and max
RSKMD ≥ TPPOSvariance (d) + TJCC (output jitter)(f) + ISI (m)
j
j
j
d= Tppos — Transmitter output pulse position (min and max)
f= Cycle-to-cycle LVDS Output jitter (TJCC) is less than 100 ps (worse case estimate)
m= extra margin - assigned to ISI in long cable applications
See Applications Informations section for more details.
FIGURE 14. Receiver Skew Margin (RSKMD) for Chipset with DESKEW
11
www.national.com
LVDS Interface
20009104
Optional features supported: Pre-emphasis and DESKEW
FIGURE 15. 48 Parallel TTL Data Bits Mapped to LVDS Bits with DC Balance Enabled
www.national.com
12
LVDS Interface (Continued)
20009135
Optional feature supported: Pre-emphasis
FIGURE 16. 48 Parallel TTL Data Bits Mapped to LVDS Bits with DC Balance Disabled
13
www.national.com
Applications Information
The DS90CR481/DS90CR482 chipset is improved over prior
generations of Channel Link devices and offers higher band-
width support and longer cable drive with three areas of
enhancement. To increase bandwidth, the maximum clock
rate is increased to 112 MHz and 8 serialized LVDS outputs
are provided. Cable drive is enhanced with a user selectable
pre-emphasis feature that provides additional output current
during transitions to counteract cable loading effects. This
requires the use of one pull up resistor to Vcc; please refer to
Table 1 to set the level needed. Optional DC balancing on a
cycle-to-cycle basis, is also provided to reduce ISI (Inter-
Symbol Interference). With pre-emphasis and DC balancing,
a low distortion eye-pattern is provided at the receiver end of
the cable. A cable deskew capability has been added to
deskew long cables of pair-to-pair skew of up to 1 LVDS
data bit time (up to 80 MHz clock rates). For details on
deskew, refer to “Deskew” section below. These three en-
hancements allow cables 5+ meters in length to be driven
depending upon media and clock rate.
NEW FEATURES DESCRIPTION
1. Pre-emphasis
Adds extra current during LVDS logic transition to reduce the
cable loading effects. Pre-emphasis strength is set via a DC
voltage level applied from min to max (0.75V to Vcc) at the
“PRE” pin. A higher input voltage on the ”PRE” pin increases
the magnitude of dynamic current during data transition. The
“PRE” pin requires one pull-up resistor (Rpre) to Vcc in order
to set the DC level. There is an internal resistor network,
which cause a voltage drop. Please refer to the tables below
to set the voltage level.
The waveshape at the Receiver input should not exhibit over
or undershoot with the proper amount of pre-emphasis set.
Too much pre-emphasis generates excess noise and in-
creases power dissipation. Cables less than 2 meters in
length typically do not require pre-emphasis.
The DS90CR481/482 chipset may also be used in a non-DC
Balance mode. In this mode pre-emphasis is supported. In
this mode, the chipset is also compatible with 21 and 28-bit
Channel Link Receivers. See Figure 16 for the LVDS map-
ping.
TABLE 1. Pre-emphasis DC voltage level with (Rpre)
Rpre
1MΩ or NC
50kΩ
Resulting PRE Voltage
Effect
0.75V
1.0V
1.5V
2.0V
2.6V
Vcc
Standard LVDS
9kΩ
50% pre-emphasis
100% pre-emphasis
3kΩ
1kΩ
100Ω
TABLE 2. Pre-emphasis needed per cable length
Frequency
PRE Voltage
1.0V
Typical cable length
112MHz
112MHz
80MHz
80MHz
66MHz
2 meters
5 meters
2 meters
5+ meters
7 meters
1.5V
1.0V
1.2V
1.5V
Note 9: This is based on testing with standard shield twisted pair cable. The amount of pre-emphasis will vary depending on the type of cable, length and operating
frequency.
2. DC Balance
data disparity minus 1 if the data is sent unmodified and 1
plus the inverse of the calculated data disparity if the data is
sent inverted. The value of the running word disparity shall
saturate at +7 and −6.
In addition to data information an additional bit is transmitted
on every LVDS data signal line during each cycle as shown
in Figure 15. This bit is the DC balance bit (DCBAL). The
purpose of the DC Balance bit is to minimize the short- and
long-term DC bias on the signal lines. This is achieved by
selectively sending the data either unmodified or inverted.
The value of the DC balance bit (DCBAL) shall be 0 when
the data is sent unmodified and 1 when the data is sent
inverted. To determine whether to send data unmodified or
inverted, the running word disparity and the current data
disparity are used. If the running word disparity is positive
and the current data disparity is positive, the data shall be
sent inverted. If the running word disparity is positive and the
current data disparity is zero or negative, the data shall be
sent unmodified. If the running word disparity is negative and
the current data disparity is positive, the data shall be sent
unmodified. If the running word disparity is negative and the
The value of the DC balance bit is calculated from the
running word disparity and the data disparity of the current
word to be sent. The data disparity of the current word shall
be calculated by subtracting the number of bits of value 0
from the number of bits value 1 in the current word. Initially,
the running word disparity may be any value between +7 and
−6. The running word disparity shall be calculated as a
continuous sum of all the modified data disparity values,
where the unmodified data disparity value is the calculated
www.national.com
14
RSKM - RECEIVER SKEW MARGIN
Applications Information (Continued)
RSKM is a chipset parameter and is explained in AN-1059 in
detail. It is the difference between the transmitter’s pulse
position and the receiver’s strobe window. RSKM must be
greater than the summation of: Interconnect skew, LVDS
Source Clock Jitter (TJCC), and ISI (if any). See Figure 13.
Interconnect skew includes PCB traces differences, connec-
tor skew and cable skew for a cable application. PCB trace
and connector skew can be compensated for in the design of
the system. Cable skew is media type and length dependant.
current data disparity is zero or negative, the data shall be
sent inverted. If the running word disparity is zero, the data
shall be sent inverted.
DC Balance mode is set when the BAL pin on the transmitter
is tied HIGH - see pin descriptions. DC Balancing is useful
on long cable applications which are typically greater than 5
meters in length.
3. Deskew
RSKMD - RECEIVER SKEW MARGIN WITH DESKEW
Deskew is supported in the DC Balance mode only (BAL =
high on DS90CR481). The “DESKEW” pin on the receiver
when set high will deskew a minimum of 1 LVDS data bit
time skew from the ideal strobe location between signals
arriving on independent differential pairs (pair-to-pair skew).
It is required that the “DS_OPT” pin on the Transmitter must
be applied low for a minimum of four clock cycles to com-
plete the deskew operation. It is also required that this must
be performed at least once at any time after the PLLs have
locked to the input clock frequency. If power is lost, or if the
cable has been switched, this procedure must be repeated
or else the receiver may not sample the incoming LVDS data
correctly. When the receiver is in the deskew mode, all
receiver outputs are set to a LOW state, but the receiver
clock output is still active and switching. Setting the
“DESKEW” pin to low will disable the deskew operation and
allow the receiver to operation on a fixed data sampling
strobe. In this case, the ”DS_OPT” pin on the transmitter
must then be set high.
RSKMD is a chipset parameter and is applicable when the
DESKEW feature of the DS90CR482 is employed. It is the
difference between the receiver’s strobe window and the
ideal pulse locations. The DESKEW feature adjusts for skew
between each data channel and the clock channel. This
feature is supported up to 80MHz clock rate. RSKMD must
be greater than the summation of: Transmitter’s Pulse Posi-
tion variance, LVDS Source Clock Jitter (TJCC), and ISI (if
any). See Figure 14. With DESKEW, RSKMD will be a
minimum of 25% of TBIT. Deskew compensates for intercon-
nect skew which includes PCB traces differences, connector
skew and cable skew (for a cable application). PCB trace
and connector skew can be compensated for in the design of
the system. Note, cable skew is media type and length
dependant. Cable length may be limited by the RSKMD
parameter prior to the interconnect skew reaching 1 TBIT in
length due to ISI effects.
POWER DOWN
The DS_OPT pin at the input of the transmitter
(DS90CR481) is used to initiate the deskew calibration pat-
tern. It must be applied low for a minimum of four clock
cycles in order for the receiver to complete the deskew
operation. For this reason, the LVDS clock signal with
DS_OPT applied high (active data sampling) shall be
1111000 or 1110000 pattern. During the deskew operation
with DS_OPT applied low, the LVDS clock signal shall be
1111100 or 1100000 pattern. The transmitter will also output
a series of 1111000 or 1110000 onto the LVDS data lines
(TxOUT 0-7) during deskew so that the receiver can auto-
matically calibrated the data sampling strobes at the receiver
inputs. Each data channel is deskewed independently and is
tuned with a step size of 1/3 of a bit time over a range of +/−1
TBIT from the ideal strobe location. The Deskew feature
operates up to clock rates of 80 MHz only. If the Receiver is
enabled in the deskew mode, then it must be trained before
data transfer.
Both transmitter and receiver provide a power down feature.
When asserted current draw through the supply pins is
minimized and the PLLs are shut down. The transmitter
outputs are in TRI-STATE when in power down mode. The
receiver outputs are forced to a active LOW state when in
the power down mode. (See Pin Description Tables). The PD
pin should be driven HIGH to enable the device once VCC is
stable.
CONFIGURATIONS
The transmitter is designed to be connected typically to a
single receiver load. This is known as a point-to-point con-
figuration. It is also possible to drive multiple receiver loads if
certain restrictions are made. Only the final receiver at the
end of the interconnect should provide termination across
the pair. In this case, the driver still sees the intended DC
load of 100 Ohms. Receivers connected to the cable be-
tween the transmitter and the final receiver must not load
down the signal. To meet this system requirement, stub
lengths from the line to the receiver inputs must be kept very
short.
CLOCK JITTER
The transmitter is designed to reject cycle-to-cycle jitter
which may be seen at the transmitter input clock. Very low
cycle-to-cycle jitter is passed on to the transmitter outputs.
Cycle-to-cycle jitter has been measured over frequency to
be less than 100 ps with input step function jitter applied.
This should be subtracted from the RSKM/RSKMD budget
as shown and described in Figure 13 and Figure 14. This
rejection capability significantly reduces the impact of jitter at
the TXinput clock pin, and improves the accuracy of data
sampling in the receiver. Transmitter output jitter is effected
by PLLVCC noise and input clock jitter - minimize supply
noise and use a low jitter clock source to limit output jitter.
The falling edge of the input clock to the transmitter is the
critical edge and is used by the PLL circuit.
CABLE TERMINATION
A termination resistor is required for proper operation to be
obtained. The termination resistor should be equal to the
differential impedance of the media being driven. This should
be in the range of 90 to 132 Ohms. 100 Ohms is a typical
value common used with standard 100 Ohm twisted pair
cables. This resistor is required for control of reflections and
also to complete the current loop. It should be placed as
close to the receiver inputs to minimize the stub length from
the resistor to the receiver input pins.
15
www.national.com
Input Characteristics" table for specifications. In addition
undershoots in excess of the ABS MAX specifications are
not recommended. If the line between the host device and
the transmitter is long and acts as a transmission line, then
termination should be employed. If the transmitter is being
driven from a device with programmable drive strengths,
data inputs are recommended to be set to a weak setting to
prevent transmission line effects. The clock signal is typically
set higher to provide a clean edge that is also low jitter.
Applications Information (Continued)
HOW TO CONFIGURE FOR BACKPLANE
APPLICATIONS
In a backplane application with differential line impedance of
100Ω the differential line pair-to-pair skew can controlled by
trace layout. The transmitter-DS90CR481 “DS_OPT” pin
may be set high. In a backplane application with short PCB
distance traces, pre-emphasis from the transmitter is typi-
cally not required. The “PRE” pin should be left open (do not
tie to ground). A resistor pad provision for a pull up resistor to
Vcc can be implemented in case pre-emphasis is needed to
counteract heavy capacitive loading effects.
UNUSED LVDS OUTPUTS
Unused LVDS output channels should be terminated with
100 Ohm at the transmitter’s output pin.
LVDS INTERCONNECT GUIDELINES
HOW TO CONFIGURE FOR CABLE INTERCONNECT
APPLICATIONS
See AN-1108 and AN-905 for full details.
In applications that require the long cable drive capability.
The DS90CR481/DS90CR482 chipset is improved over prior
generations of Channel Link devices and offers higher band-
width support and longer cable drive with the use of DC
balanced data transmission, pre-emphasis. Cable drive is
enhanced with a user selectable pre-emphasis feature that
provides additional output current during transitions to coun-
teract cable loading effects. This requires the use of one pull
up resistor to Vcc; please refer to Table 1 to set the level
needed. Optional DC balancing on a cycle-to-cycle basis, is
also provided to reduce ISI (Inter-Symbol Interference) for
long cable applications. With pre-emphasis and DC balanc-
ing, a low distortion eye-pattern is provided at the receiver
end of the cable. These enhancements allow cables 5+
meters in length to be driven. Depending upon clock rate and
the media being driven, the cable Deskew feature may also
be employed - see discussion on DESKEW, RSKM and
RSKMD above.
•
•
Use 100Ω coupled differential pairs
Use the S/2S/3S rule in spacings
— S = space between the pair
— 2S = space between pairs
— 3S = space to TTL signal
Minimize the number of VIA
•
•
Use differential connectors when operating above
500Mbps line speed
•
•
•
•
Maintain balance of the traces
Minimize skew within the pair
Minimize skew between pairs
Terminate as close to the RXinputs as possible
RECEIVER OUTPUT DRIVE STRENGTH
The DS90CR482 output specify a 8pF load, VOH and VOL
are tested at 2mA, which is intended for only 1 or maybe
2 loads. If high fan-out is required or long transmission line
driving capability, buffering the receiver output is recom-
mended. Receiver outputs do not support / provide a TRI-
STATE function.
SUPPLY BYPASS RECOMMENDATIONS
Bypass capacitors must be used on the power supply pins.
Different pins supply different portions of the circuit, there-
fore capacitors should be nearby all power supply pins ex-
cept as noted in the pin description table. Use high fre-
quency ceramic (surface mount recommended) 0.1µF
capacitors close to each supply pin. If space allows, a
0.01µF capacitor should be used in parallel, with the small-
est value closest to the device pin. Additional scattered
capacitors over the printed circuit board will improve decou-
pling. Multiple (large) via should be used to connect the
decoupling capacitors to the power plane. A 4.7 to 10 µF bulk
cap is recommended near the PLLVCC pins and also the
LVDSVCC (pin #40) on the Transmitter. Connections be-
tween the caps and the pin should use wide traces.
DS90CR483/484
The DS90CR481/2 chipset is electrically similar to the
DS90CR483/4. The DS90CR481/2 differ only in the control
circuit of the internal PLL and are specified for 65 to 112 MHz
operation. The devices will directly inter-operate within the
scope of the respective datasheets.
FOR MORE INFORMATION
Channel Link Applications Notes currently available:
•
•
•
•
•
AN-1041 Introduction to Channel Link
AN-1059 RSKM Calculations
INPUT SIGNAL QUALITY REQUIREMENTS -
TRANSMITTER
AN-1108 PCB and Interconnect Guidelines
AN-905 Differential Impedance
The input signal quality must comply to the datasheet re-
quirements, please refer to the "Recommended Transmitter
National’s LVDS Owner’s Manual
www.national.com
16
DS90CR481 Pin Descriptions—Channel Link Transmitter
Pin Name
I/O
Description
TxIN
I
TTL level input. (Note 10).
TxOUTP
TxOUTM
TxCLKIN
TxCLKP
TxCLKM
PD
O
O
I
Positive LVDS differential data output.
Negative LVDS differential data output.
TTL level clock input. The rising edge acts as data strobe.
Positive LVDS differential clock output.
O
O
I
Negative LVDS differential clock output.
TTL level input. Assertion (low input) tri-states the outputs, ensuring low
current at power down. (Note 10).
PLLSEL
PRE
I
I
PLL range select. This pin must be tied to VCC. NC or tied to Ground is
reserved for future use. (Note 10)
Pre-emphasis “level” select. Pre-emphasis is active when input is tied to VCC
through external pull-up resistor. Resistor value determines Pre-emphasis
level (See Applications Information Section). For normal LVDS drive level
(No Pre-emphasis) leave this pin open (do not tie to ground).
Cable Deskew performed when TTL level input is low. No TxIN data is
sampled during Deskew. To perform Deskew function, input must be held
low for a minimum of 4 clock cycles. The Deskew operation is normally
conducted after the TX and RX PLLs have locked. It should also be
conducted after a system reset, or a reconfiguration event. It must be
peformed at least once when "DESKEW" is enabled. (Note 10)
TTL level input. This pin was previously labeled as VCC, which enabled the
DC Balance function. But when tied low or left open, the DC Balance
function is disabled. Please refer to (Figures 15, 16) for LVDS data bit
mapping respectively. (Note 10), (Note 12)
DS_OPT
I
BAL
VCC
I
I
Power supply pins for TTL inputs and digital circuitry. Bypass not required
on Pins 20 and 21.
GND
I
I
I
I
I
Ground pins for TTL inputs and digital circuitry.
PLLVCC
PLLGND
LVDSVCC
LVDSGND
NC
Power supply pin for PLL circuitry.
Ground pins for PLL circuitry.
Power supply pin for LVDS outputs.
Ground pins for LVDS outputs.
No Connect. Make NO Connection to these pins - leave open.
Note 10: Inputs default to “low” when left open due to internal pull-down resistor.
17
www.national.com
DS90CR482 Pin Descriptions—Channel Link Receiver
Pin Name
I/O
Description
RxINP
I
I
Positive LVDS differential data inputs.
RxINM
RxOUT
Negative LVDS differential data inputs.
O
TTL level data outputs. In PowerDown (PD = Low) mode, receiver outputs are
forced to a Low state.
RxCLKP
RxCLKM
RxCLKOUT
PLLSEL
I
I
Positive LVDS differential clock input.
Negative LVDS differential clock input.
O
I
TTL level clock output. The rising edge acts as data strobe.
PLL range select. This pin must be tied to VCC. NC or tied to Ground is reserved for
future use. (Note 10)
DESKEW
I
Deskew / Oversampling “on/off” select. When using the Deskew / Oversample
feature this pin must be tied to VCC. Tieing this pin to ground disables this feature.
(Note 10) Deskew is only supported in the DC Balance mode.
TTL level input. When asserted (low input) the receiver outputs are Low. (Note 10)
Power supply pins for TTL outputs and digital circuitry. Bypass not required on Pins
6 and 77.
PD
I
I
VCC
GND
I
I
I
I
I
Ground pins for TTL outputs and digital circuitry.
Power supply for PLL circuitry.
PLLVCC
PLLGND
LVDSVCC
LVDSGND
NC
Ground pin for PLL circuitry.
Power supply pin for LVDS inputs.
Ground pins for LVDS inputs.
No Connect. Make NO Connection to these pins - leave open.
Note 11: These receivers have input fail-safe bias circuitry to guarantee a stable receiver output for floating or terminated receiver inputs. Under test conditions
receiver inputs will be in a HIGH state. If the cable interconnect (media) are disconnected which results in floating/terminated inputs, the outputs will remain in the
last valid state.
Note 12: The DS90CR482 is design to automatically detect the DC Balance or non-DC Balance transmitted data from the DS90CR481 and deserialize the LVDS
data according to the define bit mapping.
www.national.com
18
DS90DR481 — Connection Diagram
Transmitter - DS90CR481 - TQFP - Top View
20009106
19
www.national.com
DS90CR482 – Connection Diagram
Receiver - DS90CR482 - TQFP - Top View
20009107
www.national.com
20
Physical Dimensions inches (millimeters) unless otherwise noted
Dimensions show in millimeters only
Order Number DS90CR481VJD or DS90CR482VS
NS Package Number VJD100A
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and whose failure to perform when
properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result
in a significant injury to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products
Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain
no ‘‘Banned Substances’’ as defined in CSP-9-111S2.
Leadfree products are RoHS compliant.
National Semiconductor
Americas Customer
Support Center
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
National Semiconductor
Asia Pacific Customer
Support Center
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
Email: ap.support@nsc.com
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
相关型号：
©2020 ICPDF网 联系我们和版权申明