74HCT4060DB,112 [NXP]
74HC(T)4060 - 14-stage binary ripple counter with oscillator SSOP1 16-Pin;型号: | 74HCT4060DB,112 |
厂家: | NXP |
描述: | 74HC(T)4060 - 14-stage binary ripple counter with oscillator SSOP1 16-Pin 光电二极管 逻辑集成电路 触发器 |
文件: | 总25页 (文件大小:135K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
74HC4060; 74HCT4060
14-stage binary ripple counter with oscillator
Rev. 03 — 14 July 2008
Product data sheet
1. General description
The 74HC4060; 74HCT4060 are high-speed Si-gate CMOS device and is pin compatible
with the HEF4060.
The 74HC4060; 74HCT4060 are 14-stage ripple-carry counter/dividers and oscillators
with three oscillator terminals (RS, RTC and CTC), ten buffered outputs (Q3 to Q9 and
Q11 to Q13) and an overriding asynchronous master reset (MR). The oscillator
configuration allows design of either RC or crystal oscillator circuits. The oscillator may be
replaced by an external clock signal at input RS. In this case keep the other oscillator pins
(RTC and CTC) floating. The counter advances on the negative-going transition of RS. A
HIGH level on MR resets the counter (Q3 to Q9 and Q11 to Q13 = LOW), independent of
other input conditions. In the HCT version, the MR input is TTL compatible, but the RS
input has CMOS input switching levels and can be driven by a TTL output by using a
pull-up resistor to VCC
.
2. Features
I All active components on chip
I RC or crystal oscillator configuration
I Complies with JEDEC standard no. 7 A
I ESD protection:
N HBM JESD22-A114E exceeds 2000 V
N MM JESD22-A115-A exceeds 200 V
I Multiple package options
I Specified from −40 °C to +85 °C and from −40 °C to +125 °C
3. Applications
I Control counters
I Timers
I Frequency dividers
I Time-delay circuits
74HC4060; 74HCT4060
NXP Semiconductors
14-stage binary ripple counter with oscillator
4. Ordering information
Table 1.
Ordering information
Type number
Package
Temperature range Name
Description
Version
74HC4060N
−40 °C to +125 °C
−40 °C to +125 °C
−40 °C to +125 °C
DIP16
plastic dual in-line package; 16 leads (300 mil)
SOT38-4
SOT109-1
SOT338-1
74HCT4060N
74HC4060D
SO16
plastic small outline package; 16 leads;
body width 3.9 mm
74HCT4060D
74HC4060DB
74HCT4060DB
74HC4060PW
SSOP16
TSSOP16
plastic shrink small outline package; 16 leads;
body width 5.3 mm
−40 °C to +125 °C
−40 °C to +125 °C
plastic thin shrink small outline package; 16 leads; SOT403-1
body width 4.4 mm
74HC4060BQ
74HCT4060BQ
DHVQFN16 plastic dual in-line compatible thermal-enhanced
very thin quad flat package; no leads; 16 terminals;
body 2.5 × 3.5 × 0.85 mm
SOT763-1
5. Functional diagram
10
9
RTC CTC
RS
Q3
Q4
7
11
12
5
MR
Q5
4
Q6
6
Q7
14
13
15
1
Q8
Q9
Q11
Q12
Q13
2
3
001aai467
Fig 1. Logic symbol
74HC_HCT4060_3
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 03 — 14 July 2008
2 of 25
74HC4060; 74HCT4060
NXP Semiconductors
14-stage binary ripple counter with oscillator
CTR14
!G
CTR14
3
7
3
7
9
10
11
12
CX
5
5
RX
4
4
+
AND
RCX
6
11
12
6
+
14
13
15
1
14
13
15
1
CT
CT
CT = 0
9
CT = 0
9
11
11
2
2
13
3
13
3
(a)
(b)
001aai468
Fig 2. IEC logic symbol
10
RTC
9
CTC
RS
11
CP
14-STAGE BINARY COUNTER
MR
MR
12
Q3 Q4 Q5 Q6 Q7 Q8 Q9 Q11 Q12 Q13
7
5
4
6
14
13
15
1
2
3
001aai113
Fig 3. Functional diagram
CTC
FF
1
FF
4
FF
10
FF
12
FF
14
RTC
RS
CP
CP
CP
CP
CP
Q
Q
Q
Q
Q
MR
MR
MR
MR
MR
MR
Q3
Q9
Q11
Q13
001aai114
Fig 4. Logic diagram
74HC_HCT4060_3
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 03 — 14 July 2008
3 of 25
74HC4060; 74HCT4060
NXP Semiconductors
14-stage binary ripple counter with oscillator
6. Pinning information
6.1 Pinning
74HC4060
74HCT4060
74HC4060
74HCT4060
terminal 1
index area
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
Q11
Q12
Q13
Q5
V
CC
Q9
2
3
4
5
6
7
15
14
13
12
11
10
Q12
Q13
Q5
Q9
Q7
Q7
Q8
Q8
Q4
MR
RS
RTC
Q4
MR
RS
Q6
(1)
CC
V
Q6
Q3
Q3
RTC
CTC
001aai469
GND
Transparent top view
001aai115
(1) The die substrate is attached to this pad using
conductive die attach material. It cannot be used as
supply pin or input.
Fig 5. Pin configuration DIP16, SO16 and (T)SSOP16
Fig 6. Pin configuration DHVQFN16
6.2 Pin description
Table 2.
Symbol
Q11 to Q13
Q3 to Q9
GND
Pin description
Pin
Description
counter output
counter output
ground (0 V)
1, 2, 3
7, 5, 4, 6, 14, 13, 15
8
CTC
9
external capacitor connection
external resistor connection
clock input /oscillator pin
master reset input (active HIGH)
supply voltage
RTC
10
11
12
16
RS
MR
VCC
74HC_HCT4060_3
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 03 — 14 July 2008
4 of 25
74HC4060; 74HCT4060
NXP Semiconductors
14-stage binary ripple counter with oscillator
7. Functional description
1
2
4
8
16
32
64
128
256
512 1024 2048 4096 8192 16384
RS
MR
Q3
Q4
Q5
Q6
Q7
Q8
Q9
Q11
Q12
Q13
001aai117
Fig 7. Timing diagram
8. Limiting values
Table 3.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol
VCC
IIK
Parameter
Conditions
Min
Max
+7
Unit
V
supply voltage
−0.5
[1]
[1]
input clamping current
output clamping current
output current
VI < −0.5 V or VI > VCC + 0.5 V
VO < −0.5 V or VO > VCC + 0.5 V
−0.5 V < VO < VCC + 0.5 V
-
±20
±20
±25
50
mA
mA
mA
mA
mA
°C
IOK
-
IO
-
ICC
supply current
-
IGND
Tstg
ground current
−50
−65
-
storage temperature
+150
74HC_HCT4060_3
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 03 — 14 July 2008
5 of 25
74HC4060; 74HCT4060
NXP Semiconductors
14-stage binary ripple counter with oscillator
Table 3.
Limiting values …continued
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol
Parameter
Conditions
Min
Max
Unit
Ptot
total power dissipation
Tamb = −40 °C to +125 °C
DIP16 package
[2]
[3]
[4]
[5]
-
-
-
-
750
500
500
500
mW
mW
mW
mW
SO16 package
(T)SSOP16 package
DHVQFN16 package
[1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
[2] Ptot derates linearly with 12 mW/K above 70 °C.
[3] Ptot derates linearly with 8 mW/K above 70 °C.
[4] Ptot derates linearly with 5.5 mW/K above 60 °C.
[5] Ptot derates linearly with 4.5 mW/K above 60 °C.
9. Recommended operating conditions
Table 4.
Recommended operating conditions
Voltages are referenced to GND (ground = 0 V)
Symbol Parameter Conditions
74HC4060
74HCT4060
Unit
Min
Typ
Max
6.0
Min
Typ
Max
5.5
VCC
VI
supply voltage
2.0
5.0
4.5
5.0
V
V
V
input voltage
0
-
VCC
VCC
+125
625
139
83
0
-
VCC
VCC
VO
output voltage
0
-
0
-
Tamb
∆t/∆V
ambient temperature
input transition rise and fall rate VCC = 2.0 V
VCC = 4.5 V
−40
-
−40
-
+125 °C
-
-
-
-
1.67
-
-
-
-
-
1.67
-
-
ns/V
139 ns/V
VCC = 6.0 V
-
ns/V
10. Static characteristics
Table 5.
Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
25 °C
−40 °C to +85 °C −40 °C to +125 °C Unit
Min Typ Max
Min
Max
Min
Max
74HC4060
VIH
HIGH-level
MR input
input voltage
VCC = 2.0 V
VCC = 4.5 V
VCC = 6.0 V
RS input
1.5 1.3
3.15 2.4
4.2 3.1
-
-
-
1.5
3.15
4.2
-
-
-
1.5
3.15
4.2
-
-
-
V
V
V
VCC = 2.0 V
VCC = 4.5 V
VCC = 6.0 V
1.7
3.6
4.8
-
-
-
-
-
-
1.7
3.6
4.8
-
-
-
1.7
3.6
4.8
-
-
-
V
V
V
74HC_HCT4060_3
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 03 — 14 July 2008
6 of 25
74HC4060; 74HCT4060
NXP Semiconductors
14-stage binary ripple counter with oscillator
Table 5.
Static characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
25 °C
−40 °C to +85 °C −40 °C to +125 °C Unit
Min Typ Max
Min
Max
Min
Max
VIL
LOW-level
MR input
input voltage
VCC = 2.0 V
-
-
-
0.8
0.5
-
-
-
0.5
1.35
1.8
-
-
-
0.5
1.35
1.8
V
V
V
VCC = 4.5 V
2.1 1.35
VCC = 6.0 V
2.8
1.8
RS input
VCC = 2.0 V
-
-
-
-
-
-
0.3
0.9
1.2
-
-
-
0.3
0.9
1.2
-
-
-
0.3
0.9
1.2
V
V
V
VCC = 4.5 V
VCC = 6.0 V
VOH
HIGH-level
output
voltage
RTC output; RS = MR = GND
IO = −20 µA; VCC = 2.0 V
IO = −20 µA; VCC = 4.5 V
IO = −20 µA; VCC = 6.0 V
IO = −2.6 mA; VCC = 4.5 V
IO = −3.3 mA; VCC = 6.0 V
RTC output; RS = MR = VCC
IO = −20 µA; VCC = 2.0 V
IO = −20 µA; VCC = 4.5 V
IO = −20 µA; VCC = 6.0 V
IO = −0.65 mA; VCC = 4.5 V
IO = −0.85 mA; VCC = 6.0 V
1.9 2.0
4.4 4.5
5.9 6.0
-
-
-
-
-
1.9
4.4
-
-
-
-
-
1.9
4.4
5.9
3.7
5.2
-
-
-
-
-
V
V
V
V
V
5.9
3.98
5.48
-
-
3.84
5.34
1.9 2.0
4.4 4.5
5.9 6.0
-
-
-
-
-
1.9
4.4
-
-
-
-
-
1.9
4.4
5.9
3.7
5.2
-
-
-
-
-
V
V
V
V
V
5.9
3.98
5.48
-
-
3.84
5.34
CTC output;
RS = VIH; MR = VIL
IO = −3.2 mA; VCC = 4.5 V
IO = −4.2 mA; VCC = 6.0 V
3.98
5.48
-
-
-
-
3.84
5.34
-
-
3.7
5.2
-
-
V
V
VI = VIH or VIL;
except RTC output
IO = −20 µA; VCC = 2.0 V
IO = −20 µA; VCC = 4.5 V
IO = −20 µA; VCC = 6.0 V
1.9 2.0
4.4 4.5
5.9 6.0
-
-
-
1.9
4.4
5.9
-
-
-
1.9
4.4
5.9
-
-
-
V
V
V
VI = VIH or VIL;
except RTC and CTC outputs
IO = −4.0 mA; VCC = 4.5 V
IO = −5.2 mA; VCC = 6.0 V
3.98
5.48
-
-
-
-
3.84
5.34
-
-
3.7
5.2
-
-
V
V
74HC_HCT4060_3
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 03 — 14 July 2008
7 of 25
74HC4060; 74HCT4060
NXP Semiconductors
14-stage binary ripple counter with oscillator
Table 5.
Static characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
25 °C
−40 °C to +85 °C −40 °C to +125 °C Unit
Min Typ Max
Min
Max
Min
Max
VOL
LOW-level
output
RTC output; RS = VCC
MR = GND
;
voltage
IO = 20 µA; VCC = 2.0 V
IO = 20 µA; VCC = 4.5 V
IO = 20 µA; VCC = 6.0 V
IO = 2.6 mA; VCC = 4.5 V
IO = 3.3 mA; VCC = 6.0 V
-
-
-
-
-
0
0
0
-
0.1
0.1
-
-
-
-
-
0.1
0.1
-
-
-
-
-
0.1
0.1
0.1
0.4
0.4
V
V
V
V
V
0.1
0.1
0.26
0.26
0.33
0.33
-
CTC output; RS = VIL;
MR = VIH
IO = 3.2 mA; VCC = 4.5 V
IO = 4.2 mA; VCC = 6.0 V
-
-
-
-
0.26
0.26
-
-
0.33
0.33
-
-
0.4
0.4
V
V
VI = VIH or VIL;
except RTC output
IO = 20 µA; VCC = 2.0 V
IO = 20 µA; VCC = 4.5 V
IO = 20 µA; VCC = 6.0 V
-
-
-
0
0
0
0.1
0.1
0.1
-
-
-
0.1
0.1
0.1
-
-
-
0.1
0.1
0.1
V
V
V
VI = VIH or VIL;
except RTC and CTC outputs
IO = 4.0 mA; VCC = 4.5 V
IO = 5.2 mA; VCC = 6.0 V
-
-
-
-
-
-
0.26
0.26
±0.1
-
-
-
0.33
0.33
±1.0
-
-
-
0.4
0.4
V
V
II
input leakage VI = VCC or GND; VCC = 6.0 V
current
±1.0
µA
ICC
CI
supply
current
VI = VCC or GND; IO = 0 A;
CC = 6.0 V
-
-
-
8.0
-
-
-
80
-
-
-
160
-
µA
V
input
3.5
pF
capacitance
74HCT4060
[1]
[1]
VIH
HIGH-level
input voltage
MR input;
VCC = 4.5 V to 5.5 V
2.0
-
-
-
-
2.0
-
-
2.0
-
-
V
V
VIL
LOW-level
input voltage
MR input;
VCC = 4.5 V to 5.5 V
0.8
0.8
0.8
74HC_HCT4060_3
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 03 — 14 July 2008
8 of 25
74HC4060; 74HCT4060
NXP Semiconductors
14-stage binary ripple counter with oscillator
Table 5.
Static characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
25 °C
−40 °C to +85 °C −40 °C to +125 °C Unit
Min Typ Max
Min
Max
Min
Max
VOH
HIGH-level
output
voltage
RTC output; RS = MR = VCC
IO = −20 µA; VCC = 4.5 V
IO = −0.65 mA; VCC = 4.5 V
RTC output; RS = MR = GND
IO = −20 µA; VCC = 4.5 V
IO = −2.6 mA; VCC = 4.5 V
4.4 4.5
3.98
-
-
4.4
-
-
4.4
3.7
-
-
V
V
-
3.84
4.4 4.5
-
-
4.4
-
-
4.4
3.7
-
-
V
V
3.98
-
3.84
CTC output; RS = VIH;
MR = VIL
IO = −3.2 mA; VCC = 4.5 V
3.98
-
-
-
-
3.84
4.4
-
-
-
3.7
4.4
3.7
-
-
-
V
V
V
VI = VIH or VIL;
except RTC output
IO = −20 µA; VCC = 4.5 V
4.4 4.5
VI = VIH or VIL;
except RTC and CTC outputs
IO = −4.0 mA; VCC = 4.5 V
3.98
-
3.84
VOL
LOW-level
output
RTC output; RS = VCC
MR = GND
;
voltage
IO = 20 µA; VCC = 4.5 V
-
-
0
-
0.1
-
-
0.1
-
-
0.1
0.4
V
V
IO = 2.6 mA; VCC = 4.5 V
0.26
0.33
CTC output; RS = VIL;
MR = VIH
IO = 3.2 mA; VCC = 4.5 V
-
-
-
0.26
0.1
-
-
0.33
0.1
-
-
0.4
0.1
V
V
VI = VIH or VIL;
except RTC output
IO = 20 µA; VCC = 4.5 V
0
VI = VIH or VIL;
except RTC and CTC outputs
IO = 4.0 mA; VCC = 4.5 V
-
-
-
-
0.26
-
-
0.33
-
-
0.4
V
II
input leakage VI = VCC or GND; VCC = 5.5 V
current
±0.1
±1.0
±1.0
µA
ICC
∆ICC
supply
current
VI = VCC or GND;
CC = 5.5 V; IO = 0 A
-
-
-
8.0
-
-
80
-
-
160
196
µA
µA
V
additional
supply
current
per input pin;
VI = VCC − 2.1 V; other inputs
at VCC or GND;
40
144
180
VCC = 4.5 V to 5.5 V; IO = 0 A
CI
input
-
3.5
-
-
-
-
-
pF
capacitance
[1] For HCT4060, only input MR (pin 12) has TTL input switching levels.
74HC_HCT4060_3
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 03 — 14 July 2008
9 of 25
74HC4060; 74HCT4060
NXP Semiconductors
14-stage binary ripple counter with oscillator
11. Dynamic characteristics
Table 6.
Dynamic characteristics
GND = 0 V; CL = 50 pF unless otherwise specified; for test circuit see Figure 11.
Symbol Parameter
Conditions
25 °C
−40 °C to +85 °C −40 °C to +125 °C Unit
Min Typ Max
Min
Max
Min
Max
74HC4060
[1]
tpd
propagation
delay
RS to Q3; see Figure 8
VCC = 2.0 V
-
-
-
-
99
36
31
29
300
60
-
-
-
-
-
375
75
-
-
-
-
-
450
90
-
ns
ns
ns
ns
VCC = 4.5 V
VCC = 5.0 V; CL = 15 pF
VCC = 6.0 V
51
64
77
[2]
Qn to Qn+1; see Figure 9
VCC = 2.0 V
-
-
-
-
22
8
80
16
-
-
-
-
-
100
20
-
-
-
-
-
120
24
-
ns
ns
ns
ns
VCC = 4.5 V
VCC = 5.0 V; CL = 15 pF
VCC = 6.0 V
6
6
14
17
20
tPHL
HIGH to LOW MR to Qn; see Figure 10
propagation
delay
VCC = 2.0 V
-
-
-
-
55
20
17
16
175
35
-
-
-
-
-
220
44
-
-
-
-
-
265
53
-
ns
ns
ns
ns
VCC = 4.5 V
VCC = 5.0 V; CL = 15 pF
VCC = 6.0 V
30
37
45
[3]
tt
transition time Qn; see Figure 8
VCC = 2.0 V
-
-
-
19
7
75
15
13
-
-
-
95
19
16
-
-
-
110
22
ns
ns
ns
VCC = 4.5 V
VCC = 6.0 V
6
19
tW
pulse width
RS (HIGH or LOW);
see Figure 8
VCC = 2.0 V
VCC = 4.5 V
80
16
14
17
6
-
-
-
100
20
-
-
-
120
24
-
-
-
ns
ns
ns
VCC = 6.0 V
5
17
20
MR (HIGH); see Figure 10
VCC = 2.0 V
80
16
14
25
9
-
-
-
100
20
-
-
-
120
24
-
-
-
ns
ns
ns
VCC = 4.5 V
VCC = 6.0 V
7
17
20
trec
recovery time MR to RS; see Figure 10
VCC = 2.0 V
VCC = 4.5 V
VCC = 6.0 V
100
20
28
10
8
-
-
-
125
25
-
-
-
150
30
-
-
-
ns
ns
ns
17
21
26
74HC_HCT4060_3
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 03 — 14 July 2008
10 of 25
74HC4060; 74HCT4060
NXP Semiconductors
14-stage binary ripple counter with oscillator
Table 6.
Dynamic characteristics …continued
GND = 0 V; CL = 50 pF unless otherwise specified; for test circuit see Figure 11.
Symbol Parameter
Conditions
25 °C
−40 °C to +85 °C −40 °C to +125 °C Unit
Min Typ Max
Min
Max
Min
Max
fmax
maximum
frequency
RS; see Figure 8
VCC = 2.0 V
6
30
-
26
80
87
95
40
-
-
-
-
-
4.8
24
-
-
-
-
-
-
4
20
-
-
-
-
-
-
MHz
MHz
MHz
MHz
pF
VCC = 4.5 V
VCC = 5.0 V; CL = 15 pF
VCC = 6.0 V
35
-
28
-
24
-
[4]
CPD
power
VI = GND to VCC
;
dissipation
capacitance
V
CC = 5 V; fi = 1 MHz
74HCT4060
[1]
[2]
tpd
propagation
delay
RS to Q3; see Figure 8
VCC = 4.5 V
-
-
33
31
66
-
-
-
83
-
-
-
99
-
ns
ns
VCC = 5.0 V; CL = 15 pF
Qn to Qn+1; see Figure 9
VCC = 4.5 V
-
-
8
6
16
-
-
-
20
-
-
-
24
-
ns
ns
VCC = 5.0 V; CL = 15 pF
tPHL
HIGH to LOW MR to Qn; see Figure 10
propagation
delay
VCC = 4.5 V
-
-
21
18
44
-
-
-
55
-
-
-
66
-
ns
ns
V
CC = 5.0 V; CL = 15 pF
[3]
tt
transition time Qn; see Figure 8
VCC = 4.5 V
-
7
15
-
19
-
22
ns
tW
pulse width
RS (HIGH or LOW);
see Figure 8
VCC = 4.5 V
16
16
26
6
6
-
-
-
20
20
33
-
-
-
24
24
39
-
-
-
ns
ns
ns
MR (HIGH); see Figure 10
VCC = 4.5 V
trec
recovery time MR to RS; see Figure 10
VCC = 4.5 V
13
fmax
maximum
frequency
RS; see Figure 8
VCC = 4.5 V
30
-
80
88
-
-
24
-
-
-
20
-
-
-
MHz
MHz
VCC = 5.0 V; CL = 15 pF
74HC_HCT4060_3
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 03 — 14 July 2008
11 of 25
74HC4060; 74HCT4060
NXP Semiconductors
14-stage binary ripple counter with oscillator
Table 6.
Dynamic characteristics …continued
GND = 0 V; CL = 50 pF unless otherwise specified; for test circuit see Figure 11.
Symbol Parameter
Conditions
25 °C
−40 °C to +85 °C −40 °C to +125 °C Unit
Min Typ Max
Min
Max
Min
Max
[4]
CPD
power
VI = GND to VCC − 1.5 V;
-
40
-
-
-
-
-
pF
dissipation
capacitance
VCC = 5 V; fi = 1 MHz
[1] tpd is the same as tPHL and tPLH
.
[2] Qn+1 is the next Qn output.
[3] tt is the same as tTHL and tTLH
.
[4] CPD is used to determine the dynamic power dissipation (PD in µW):
PD = CPD × VCC2 × fi × N + ∑(CL × VCC2 × fo) where:
fi = input frequency in MHz;
fo = output frequency in MHz;
CL = output load capacitance in pF;
VCC = supply voltage in V;
N = number of inputs switching;
∑(CL × VCC2 × fo) = sum of outputs.
12. Waveforms
1/f
max
V
I
RS input
GND
V
M
t
W
t
t
PHL
PLH
V
OH
90 %
90 %
V
Q3 output
M
10 %
10 %
V
OL
t
t
THL
TLH
001aai118
Measurement points are given in Table 7.
VOL and VOH are typical voltage output levels that occur with the output load.
Fig 8. Waveforms showing the clock (RS) to output (Q3) propagation delays, the clock pulse width, the output
transition times and the maximum clock frequency
74HC_HCT4060_3
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 03 — 14 July 2008
12 of 25
74HC4060; 74HCT4060
NXP Semiconductors
14-stage binary ripple counter with oscillator
V
OH
Qn output
V
M
V
OL
t
t
PLH
PHL
V
OH
V
Qn+1 output
M
V
OL
001aai120
Measurement points are given in Table 7.
VOL and VOH are typical voltage output levels that occur with the output load.
Fig 9. Waveforms showing the output Qn to output Qn+1 propagation delays
V
I
MR input
GND
V
M
T
t
rec
W
V
I
RS input
GND
V
M
t
PHL
V
OH
V
Qn output
M
V
OL
001aai119
Measurement points are given in Table 7.
VOL and VOH are typical voltage output levels that occur with the output load.
Fig 10. Waveforms showing the master reset (MR) pulse width, the master reset to output (Qn) propagation
delays and the master reset to clock (RS) recovery time
Table 7.
Type
Measurement points
Input
VM
Output
VM
74HC4060
0.5 × VCC
1.3 V
0.5 × VCC
1.3 V
74HCT4060
74HC_HCT4060_3
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 03 — 14 July 2008
13 of 25
74HC4060; 74HCT4060
NXP Semiconductors
14-stage binary ripple counter with oscillator
t
W
V
I
90 %
negative
pulse
V
V
V
V
M
M
10 %
GND
t
t
r
f
t
t
f
r
V
I
90 %
positive
pulse
M
M
10 %
GND
t
W
V
CC
V
V
O
I
G
DUT
R
T
C
L
001aah768
Test data is given in Table 8.
Definitions test circuit:
RT = Termination resistance should be equal to output impedance Zo of the pulse generator.
CL = Load capacitance including jig and probe capacitance.
Fig 11. Test circuit for measuring switching times
Table 8.
Type
Test data
Input
Load
VI
tr, tf
6 ns
6 ns
CL
74HC4060
VCC
3 V
15 pF, 50 pF
15 pF, 50 pF
74HCT4060
74HC_HCT4060_3
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 03 — 14 July 2008
14 of 25
74HC4060; 74HCT4060
NXP Semiconductors
14-stage binary ripple counter with oscillator
13. RC oscillator
13.1 Timing component limitations
The oscillator frequency is mainly determined by RtCt, provided R2 ≈ 2Rt and
R2C2 << RtCt. The function of R2 is to minimize the influence of the forward voltage
across the input protection diodes on the frequency. The stray capacitance C2 should be
kept as small as possible. In consideration of accuracy, Ct must be larger than the inherent
stray capacitance. Rt must be larger than the ON resistance in series with it, which
typically is 280 Ω at VCC = 2.0 V, 130 Ω at VCC = 4.5 V and 100 Ω at VCC = 6.0 V.
74HC4060
74HCT4060
MR (from logic)
11 RS
RTC
10
CTC
9
C2
R2
R
C
t
t
001aai121
1
Typical formula for oscillator frequency: f osc
=
------------------------------
2.5 × Rt × Ct
Fig 12. Example of a RC oscillator
The recommended values for these components to maintain agreement with the typical
oscillation formula are:
Ct > 50 pF, up to any practical value and 10 kΩ < Rt < 1 MΩ.
In order to avoid start-up problems, Rt ≥ 1 kΩ.
13.2 Typical crystal oscillator circuit
In Figure 13, R2 is the power limiting resistor. For starting and maintaining oscillation a
minimum transconductance is necessary, so R2 should not be too large. A practical value
for R2 is 2.2 kΩ.
74HC_HCT4060_3
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 03 — 14 July 2008
15 of 25
74HC4060; 74HCT4060
NXP Semiconductors
14-stage binary ripple counter with oscillator
Rbias
74HC4060
MR (from logic)
11 RS
74HCT4060
560 kΩ
V
DD
0.47 pF
100 µF
RTC
10
Rbias
100 kΩ to 1MΩ
V
I
input
output
A
I
O
(f = 1 kHz)
i
R2
2.2 kΩ
GND
001aai123
gfs = ∆IO / ∆VI at VO is constant; MR = LOW.
C3
22 pF to 37 pF
C2
100 pF
See also Figure 15.
001aai122
Fig 13. External component connection for a crystal
oscillator
Fig 14. Test set-up for measuring forward
transconductance
001aai124
(1)
14
g
fs
(mA/V)
(2)
(3)
10
6
2
0
2
4
6
V
(V)
CC
Tamb = 25 °C.
(1) Maximum.
(2) Typical.
(3) Minimum.
Fig 15. Typical forward transconductance as function of the supply voltage
74HC_HCT4060_3
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 03 — 14 July 2008
16 of 25
74HC4060; 74HCT4060
NXP Semiconductors
14-stage binary ripple counter with oscillator
001aai125
001aai127
5
5
10
10
f
f
osc
(Hz)
osc
R
t
(Hz)
4
3
2
4
3
2
10
10
C
t
10
10
10
10
10
10
10
10
3
4
5
6
−4
−3
−2
−1
10
10
10
10
10
10
R (Ω)
t
C (µF)
t
VCC = 2.0 V to 6.0 V; Tamb = 25 °C.
For Rt curve: Ct = 1 nF; R2 = 2 × Rt.
VCC = 2.0 V to 6.0 V; Tamb = 25 °C.
For Ct curve: Rt = 100 kΩ; R2 = 200 kΩ.
Fig 16. RC oscillator frequency as a function of Rt
Fig 17. RC oscillator frequency as a function of Ct
74HC_HCT4060_3
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 03 — 14 July 2008
17 of 25
74HC4060; 74HCT4060
NXP Semiconductors
14-stage binary ripple counter with oscillator
14. Package outline
DIP16: plastic dual in-line package; 16 leads (300 mil)
SOT38-4
D
M
E
A
2
A
A
1
L
c
e
w M
Z
b
1
(e )
1
b
b
2
16
9
M
H
pin 1 index
E
1
8
0
5
10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
(1)
A
A
A
2
(1)
(1)
Z
1
w
UNIT
mm
b
b
b
c
D
E
e
e
L
M
M
H
1
2
1
E
max.
min.
max.
max.
1.73
1.30
0.53
0.38
1.25
0.85
0.36
0.23
19.50
18.55
6.48
6.20
3.60
3.05
8.25
7.80
10.0
8.3
4.2
0.51
3.2
2.54
0.1
7.62
0.3
0.254
0.01
0.76
0.068 0.021 0.049 0.014
0.051 0.015 0.033 0.009
0.77
0.73
0.26
0.24
0.14
0.12
0.32
0.31
0.39
0.33
inches
0.17
0.02
0.13
0.03
Note
1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
JEITA
95-01-14
03-02-13
SOT38-4
Fig 18. Package outline SOT38-4 (DIP16)
74HC_HCT4060_3
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 03 — 14 July 2008
18 of 25
74HC4060; 74HCT4060
NXP Semiconductors
14-stage binary ripple counter with oscillator
SO16: plastic small outline package; 16 leads; body width 3.9 mm
SOT109-1
D
E
A
X
v
c
y
H
M
A
E
Z
16
9
Q
A
2
A
(A )
3
A
1
pin 1 index
θ
L
p
L
1
8
e
w
M
detail X
b
p
0
2.5
scale
5 mm
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
A
(1)
(1)
(1)
UNIT
A
A
A
b
c
D
E
e
H
L
L
p
Q
v
w
y
Z
θ
1
2
3
p
E
max.
0.25
0.10
1.45
1.25
0.49
0.36
0.25
0.19
10.0
9.8
4.0
3.8
6.2
5.8
1.0
0.4
0.7
0.6
0.7
0.3
mm
1.27
0.05
1.05
0.041
1.75
0.25
0.01
0.25
0.01
0.25
0.1
8o
0o
0.010 0.057
0.004 0.049
0.019 0.0100 0.39
0.014 0.0075 0.38
0.16
0.15
0.244
0.228
0.039 0.028
0.016 0.020
0.028
0.012
inches
0.069
0.01 0.004
Note
1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
JEITA
99-12-27
03-02-19
SOT109-1
076E07
MS-012
Fig 19. Package outline SOT109-1 (SO16)
74HC_HCT4060_3
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 03 — 14 July 2008
19 of 25
74HC4060; 74HCT4060
NXP Semiconductors
14-stage binary ripple counter with oscillator
SSOP16: plastic shrink small outline package; 16 leads; body width 5.3 mm
SOT338-1
D
E
A
X
c
y
H
v
M
A
E
Z
9
16
Q
A
2
A
(A )
3
A
1
pin 1 index
θ
L
p
L
8
1
detail X
w
M
b
p
e
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
A
(1)
(1)
(1)
UNIT
A
A
A
b
c
D
E
e
H
L
L
Q
v
w
y
Z
θ
p
p
1
2
3
E
max.
8o
0o
0.21
0.05
1.80
1.65
0.38
0.25
0.20
0.09
6.4
6.0
5.4
5.2
7.9
7.6
1.03
0.63
0.9
0.7
1.00
0.55
mm
2
0.25
0.65
1.25
0.2
0.13
0.1
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
JEITA
99-12-27
03-02-19
SOT338-1
MO-150
Fig 20. Package outline SOT338-1 (SSOP16)
74HC_HCT4060_3
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 03 — 14 July 2008
20 of 25
74HC4060; 74HCT4060
NXP Semiconductors
14-stage binary ripple counter with oscillator
TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm
SOT403-1
D
E
A
X
c
y
H
v
M
A
E
Z
9
16
Q
(A )
3
A
2
A
A
1
pin 1 index
θ
L
p
L
1
8
detail X
w
M
b
p
e
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
A
(1)
(2)
(1)
UNIT
A
A
A
b
c
D
E
e
H
L
L
Q
v
w
y
Z
θ
1
2
3
p
E
p
max.
8o
0o
0.15
0.05
0.95
0.80
0.30
0.19
0.2
0.1
5.1
4.9
4.5
4.3
6.6
6.2
0.75
0.50
0.4
0.3
0.40
0.06
mm
1.1
0.65
0.25
1
0.2
0.13
0.1
Notes
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
2. Plastic interlead protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
JEITA
99-12-27
03-02-18
SOT403-1
MO-153
Fig 21. Package outline SOT403-1 (TSSOP16)
74HC_HCT4060_3
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 03 — 14 July 2008
21 of 25
74HC4060; 74HCT4060
NXP Semiconductors
14-stage binary ripple counter with oscillator
DHVQFN16: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads;
16 terminals; body 2.5 x 3.5 x 0.85 mm
SOT763-1
B
A
D
A
A
1
E
c
detail X
terminal 1
index area
C
terminal 1
index area
e
1
y
y
e
b
v
M
C
C
A
B
C
1
w
M
2
7
L
1
8
9
E
h
e
16
15
10
D
h
X
0
2.5
scale
5 mm
DIMENSIONS (mm are the original dimensions)
(1)
A
(1)
(1)
UNIT
A
b
c
E
e
e
y
D
D
E
L
v
w
y
1
1
h
1
h
max.
0.05 0.30
0.00 0.18
3.6
3.4
2.15
1.85
2.6
2.4
1.15
0.85
0.5
0.3
mm
0.05
0.1
1
0.2
0.5
2.5
0.1
0.05
Note
1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
JEITA
02-10-17
03-01-27
SOT763-1
- - -
MO-241
- - -
Fig 22. Package outline SOT763-1 (DHVQFN16)
74HC_HCT4060_3
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 03 — 14 July 2008
22 of 25
74HC4060; 74HCT4060
NXP Semiconductors
14-stage binary ripple counter with oscillator
15. Abbreviations
Table 9.
Acronym
CMOS
DUT
Abbreviations
Description
Complementary Metal-Oxide Semiconductor
Device Under Test
ESD
ElectroStatic Discharge
Human Body Model
HBM
MM
Machine Model
TTL
Transistor-Transistor Logic
16. Revision history
Table 10. Revision history
Document ID
Release date
20080714
Data sheet status
Change notice Supersedes
74HC_HCT4060_3
Modifications:
Product data sheet
-
74HC_HCT4060_CNV_2
• The format of this data sheet has been redesigned to comply with the new identity
guidelines of NXP Semiconductors.
• Legal texts have been adapted to the new company name where appropriate.
• Section 4: DHVQFN16 package added.
• Section 8: derating values added for DHVQFN16 package.
• Section 14: outline drawing added for DHVQFN16 package.
74HC_HCT4060_CNV_2
19970901
Product specification
-
-
74HC_HCT4060_3
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 03 — 14 July 2008
23 of 25
74HC4060; 74HCT4060
NXP Semiconductors
14-stage binary ripple counter with oscillator
17. Legal information
18. Data sheet status
Document status[1][2]
Product status[3]
Development
Definition
Objective [short] data sheet
This document contains data from the objective specification for product development.
This document contains data from the preliminary specification.
This document contains the product specification.
Preliminary [short] data sheet Qualification
Product [short] data sheet Production
[1]
[2]
[3]
Please consult the most recently issued document before initiating or completing a design.
The term ‘short data sheet’ is explained in section “Definitions”.
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
malfunction of an NXP Semiconductors product can reasonably be expected
18.1 Definitions
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) may cause permanent
damage to the device. Limiting values are stress ratings only and operation of
the device at these or any other conditions above those given in the
Characteristics sections of this document is not implied. Exposure to limiting
values for extended periods may affect device reliability.
Terms and conditions of sale — NXP Semiconductors products are sold
subject to the general terms and conditions of commercial sale, as published
at http://www.nxp.com/profile/terms, including those pertaining to warranty,
intellectual property rights infringement and limitation of liability, unless
explicitly otherwise agreed to in writing by NXP Semiconductors. In case of
any inconsistency or conflict between information in this document and such
terms and conditions, the latter will prevail.
18.2 Disclaimers
General — Information in this document is believed to be accurate and
reliable. However, NXP Semiconductors does not give any representations or
warranties, expressed or implied, as to the accuracy or completeness of such
information and shall have no liability for the consequences of use of such
information.
No offer to sell or license — Nothing in this document may be interpreted
or construed as an offer to sell products that is open for acceptance or the
grant, conveyance or implication of any license under any copyrights, patents
or other industrial or intellectual property rights.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
18.3 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in medical, military, aircraft,
space or life support equipment, nor in applications where failure or
19. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
74HC_HCT4060_3
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 03 — 14 July 2008
24 of 25
74HC4060; 74HCT4060
NXP Semiconductors
14-stage binary ripple counter with oscillator
20. Contents
1
2
3
4
5
General description . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Ordering information. . . . . . . . . . . . . . . . . . . . . 2
Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2
6
6.1
6.2
Pinning information. . . . . . . . . . . . . . . . . . . . . . 4
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4
7
Functional description . . . . . . . . . . . . . . . . . . . 5
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 5
Recommended operating conditions. . . . . . . . 6
Static characteristics. . . . . . . . . . . . . . . . . . . . . 6
Dynamic characteristics . . . . . . . . . . . . . . . . . 10
Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
8
9
10
11
12
13
13.1
13.2
RC oscillator. . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Timing component limitations . . . . . . . . . . . . . 15
Typical crystal oscillator circuit . . . . . . . . . . . . 15
14
15
16
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 18
Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . 23
Revision history. . . . . . . . . . . . . . . . . . . . . . . . 23
17
18
18.1
18.2
18.3
Legal information. . . . . . . . . . . . . . . . . . . . . . . 24
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 24
Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 24
19
20
Contact information. . . . . . . . . . . . . . . . . . . . . 24
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2008.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
Date of release: 14 July 2008
Document identifier: 74HC_HCT4060_3
相关型号:
74HCT4060DB-T
IC HCT SERIES, ASYN NEGATIVE EDGE TRIGGERED 14-BIT UP BINARY COUNTER, PDSO16, 5.30 MM, PLASTIC, MO-150, SOT-338-1, SSOP-16, Counter
NXP
©2020 ICPDF网 联系我们和版权申明