935286689112 [NXP]
DATACOM, INTERFACE CIRCUIT, PDSO8, 3.90 MM, PLASTIC, MS-012, SO-8;
| 型号： | 935286689112 |
| 厂家： | 
NXP |
| 描述： | DATACOM, INTERFACE CIRCUIT, PDSO8, 3.90 MM, PLASTIC, MS-012, SO-8 电信 光电二极管 电信集成电路 |
| 文件： | 总22页 (文件大小：129K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
INTEGRATED CIRCUITS
DATA SHEET
TJA1020
LIN transceiver
Product specification
2004 Jan 13
Supersedes data of 2002 Jul 17
Philips Semiconductors
Product specification
LIN transceiver
TJA1020
FEATURES
General
GENERAL DESCRIPTION
The TJA1020 is the interface between the LIN
master/slave protocol controller and the physical bus in a
Local Interconnect Network (LIN). It is primarily intended
for in-vehicle sub-networks using baud rates from 2.4 up to
20 Kbaud.
• Baud rate up to 20 Kbaud
• Very low ElectroMagnetic Emission (EME)
• High ElectroMagnetic Immunity (EMI)
• Low slope mode for an even further reduction of EME
• Passive behaviour in unpowered state
• Input levels compatible with 3.3 and 5 V devices
The transmit data stream of the protocol controller at the
TXD input is converted by the LIN transceiver into a bus
signal with controlled slew rate and wave shaping to
minimize EME. The LIN bus output pin is pulled HIGH via
an internal termination resistor. For a master application
an external resistor in series with a diode should be
connected between pin INH or pin BAT and pin LIN. The
receiver detects the data stream at the LIN bus input pin
and transfers it via pin RXD to the microcontroller.
• Integrated termination resistor for Local Interconnect
Network (LIN) slave applications
• Wake-up source recognition (local or remote)
• Supports K-line like functions.
Low power management
In normal transceiver operation the TJA1020 can be
switched in the normal slope mode or the low slope mode.
In the low slope mode the TJA1020 lengthens the rise and
fall slopes of the LIN bus signal, thus further reducing the
already very low emission in normal slope mode.
• Very low current consumption in sleep mode with local
and remote wake-up.
Protections
In sleep mode the power consumption of the TJA1020 is
very low, whereas in failure modes the power consumption
is reduced to a minimum.
• Transmit data (TXD) dominant time-out function
• Bus terminal and battery pin protected against
transients in the automotive environment (ISO7637)
• Bus terminal short-circuit proof to battery and ground
• Thermally protected.
QUICK REFERENCE DATA
SYMBOL
VBAT
PARAMETER
MIN.
TYP. MAX. UNIT
supply voltage on pin BAT
5
12
3
27
8
V
IBAT
supply current on pin BAT in sleep mode
1
µA
supply current on pin BAT in standby mode; bus recessive
supply current on pin BAT in normal slope mode; bus recessive
supply current on pin BAT in normal slope mode; bus dominant
DC voltage on pin LIN
100
100
1
400
400
3.5
−
1000 µA
1000 µA
8.0
mA
V
VLIN
−27
−40
−4
+40
Tvj
virtual junction temperature
−
+150 °C
Vesd(HBM)
electrostatic discharge voltage; human body model;
pins NWAKE, LIN and BAT
−
+4
kV
ORDERING INFORMATION
TYPE
PACKAGES
NUMBER
NAME
DESCRIPTION
VERSION
SOT96-1
−
TJA1020T
TJA1020U
SO8
plastic small outline package; 8 leads; body width 3.9 mm
−
bare die; die dimensions 1480 × 1760 × 375 µm
2004 Jan 13
2
Philips Semiconductors
Product specification
LIN transceiver
TJA1020
BLOCK DIAGRAM
7
BAT
WAKE-UP
TIMER
3
NWAKE
CONTROL
8
INH
SLEEP/
NORMAL
TIMER
TEMPERATURE
PROTECTION
2
NSLP
6
LIN
TXD
TIME-OUT
TIMER
4
TXD
TJA1020T
BUS
TIMER
1
RXD
RXD/
INT
5
FILTER
GND
MGU241
Fig.1 Block diagram.
PINNING
SYMBOL PIN
DESCRIPTION
RXD
1
receive data output (open-drain);
active LOW after a wake-up event
NSLP
2
sleep control input (active LOW);
controls inhibit output; resets
wake-up source flag on TXD and
wake-up request on RXD
handbook, halfpage
RXD
NSLP
1
2
3
4
8
INH
BAT
LIN
7
6
5
NWAKE
TXD
3
4
local wake-up input (active LOW);
negative edge triggered
TJA1020T
NWAKE
TXD
transmit data input; active LOW
output after a local wake-up event
GND
MGU242
GND
LIN
5
6
7
8
ground
LIN bus line input/output
battery supply
BAT
INH
battery related inhibit output for con-
trolling an external voltage regulator;
active HIGH after a wake-up event
Fig.2 Pinning diagram.
2004 Jan 13
3
Philips Semiconductors
Product specification
LIN transceiver
TJA1020
FUNCTIONAL DESCRIPTION
The TJA1020 is the interface between the LIN master/slave protocol controller and the physical bus in a Local
Interconnect Network (LIN). The LIN transceiver is optimized for the maximum specified LIN transmission speed of
20 Kbaud providing optimum EMC performance due to wave shaping of the LIN output.
Operating modes
The TJA1020 provides two modes of normal operation, one intermediate mode and one very low power mode. Figure 3
shows the state diagram.
NORMAL
SLOPE MODE
t
> t
(NSLP = 1; after 0−>1) gotonorm
STANDBY
while TXD = 1
INH = HIGH
TERM. = 30 kΩ
RXD = LOW
trx OFF
INH = HIGH
TERM. = 30 kΩ
RXD = LINDATA
trx ON
(t
> t
(NWAKE = 0; after 1−>0) NWAKE
or
t
> t
)
(LIN = 0; after 1−>0) BUS
t
(NSLP = 0; after 1−>0)
> t
t
> t
gotosleep
t
> t
(NSLP = 1; after 0−>1) gotonorm
(NSLP = 1; after 0−>1) gotonorm
while TXD = 1
while TXD = 0
while TXD = 1
t
> t
(NSLP = 0; after 1−>0) gotosleep
SLEEP
LOW
SLOPE MODE
while TXD = 1
INH = FLOATING
TERM. =
HIGH-OHMIC
INH = HIGH
TERM. = 30 kΩ
RXD = LINDATA
trx ON
RXD = FLOATING
trx OFF
t
> t
(NSLP = 1; after 0−>1) gotonorm
switching on BAT
while TXD = 0
MGU243
trx: transmitter.
TERM.: slave termination resistor, connected between pins LIN and BAT.
Fig.3 State diagram.
2004 Jan 13
4
Philips Semiconductors
Product specification
LIN transceiver
TJA1020
Table 1 Operating modes
MODE
Sleep
Standby(1)
NSLP
TXD (OUTPUT)
RXD
floating
INH
TRANSMITTER
REMARKS
0
0
weak pull-down
floating off
HIGH off
no wake-up request detected
weak pull-down if LOW; note 3
remote wake-up;
strong pull-down if
local wake-up;
wake-up request detected; in
this mode the microcontroller
can read the wake-up source:
remote or local wake-up
note 2
Normal
slope
mode
1
1
weak pull-down
HIGH:
recessive state
LOW:
HIGH normal slope
mode
notes 2, 3 and 4
dominant state
Low slope
mode
weak pull-down
HIGH:
recessive state
LOW:
HIGH low slope mode notes 2, 3 and 5
dominant state
Notes
1. The standby mode is entered automatically upon any local or remote wake-up event during sleep mode. Pin INH and
the 30 kΩ termination resistor at pin LIN are switched on.
2. The internal wake-up source flag (set if a local wake-up did occur and fed to pin TXD) will be reset when entering
normal slope or low slope mode (NSLP goes HIGH).
3. The wake-up interrupt (on pin RXD) is released when entering normal slope or low slope mode (NSLP goes HIGH).
4. The normal slope mode is entered during a positive edge on NSLP while pin TXD is already set HIGH. In the event
of a short-circuit to ground on pin TXD, the transmitter will be disabled.
5. The low slope mode is entered during the positive edge on NSLP while pin TXD is already pulled LOW.
Sleep mode
The sleep mode can be activated independently from the
actual level on pin LIN or NWAKE. So it is guaranteed that
the lowest power consumption is achievable even in case
of a continuous dominant level on pin LIN or a continuous
LOW on pin NWAKE.
This mode is the most power saving mode of the TJA1020
and the default state after power-up (first battery supply).
Despite its extreme low current consumption, the TJA1020
can still be waken up remotely via pin LIN, or waken up
locally via pin NWAKE, or activated directly via pin NSLP.
Filters at the inputs of the receiver (LIN), of pin NWAKE
and of pin NSLP are preventing unwanted wake-up events
due to automotive transients or EMI. All wake-up events
Standby mode
The standby mode is entered automatically whenever a
local or remote wake-up occurs while the TJA1020 is in its
sleep mode. These wake-up events activate pin INH and
enable the slave termination resistor at the pin LIN. As a
result of the HIGH condition on pin INH the voltage
regulator and the microcontroller can be activated.
have to be maintained for a certain time period (tBUS
tNWAKE and tgotonorm).
,
The sleep mode is initiated by a falling edge on the pin
NSLP while TXD is already set HIGH. After a filter time
continuously driven sleep command (pin NSLP = LOW),
pin INH becomes floating.
The standby mode is signalled by a LOW level on pin RXD
which can be used as an interrupt for the microcontroller.
In sleep mode the internal slave termination between
pins LIN and BAT is disabled to minimize the power
dissipation in case pin LIN is short-circuited to ground.
Only a weak pull-up between pins LIN and BAT is present.
In the standby mode (pin NSLP is still LOW), the condition
of pin TXD (weak pull-down or strong pull-down) indicates
the wake-up source: weak pull-down for a remote wake-up
request and strong pull-down for a local wake-up request.
2004 Jan 13
5
Philips Semiconductors
Product specification
LIN transceiver
TJA1020
Setting pin NSLP HIGH during standby mode results in the
following events:
In the low slope mode the transmitter output stage drives
the LIN bus line with lengthened rise and fall slopes. This
will further reduce the already outstanding EME in the
normal slope mode. The low slope mode is perfectly suited
for applications where transmission speed is not critical.
The mode selection is done by the LIN transceiver after a
positive edge on pin NSLP, maintained for a certain time
period (tgotonorm). If pin TXD is LOW at that time, the low
slope mode is entered, otherwise the normal mode is
entered. The transition to the low slope mode will be
executed during an open pin TXD (fail-safe), a short-circuit
from pin TXD to ground (fail-safe) or an intended LOW
level of pin TXD programmed by the microcontroller. The
transmitter is enabled after a LOW-to-HIGH transition on
pin TXD. In the event of a short-circuit to ground on pin
TXD, the transmitter will be disabled.
• An immediate reset of the wake-up source flag; thus
releasing the possible strong pull-down at pin TXD
before the actual mode change (after tgotonorm) is
performed
• A change into normal slope mode if the HIGH level on
pin NSLP has been maintained for a certain time period
(tgotonorm) while pin TXD is pulled HIGH
• A change into low slope mode if the HIGH level on pin
NSLP has been maintained for a certain time period
(tgotonorm) while pin TXD is pulled LOW either
deliberately driven by the microcontroller, or due to a
failure. In the event of a short-circuit to ground or an
open-wire on pin TXD, the LIN output remains recessive
(fail safe)
Wake-up
• A reset of the wake-up request signal on pin RXD if the
HIGH level on pin NSLP has been maintained for a
certain time period (tgotonorm).
There are three ways to wake-up a TJA1020 which is in
sleep mode:
1. Remote wake-up via a dominant bus state
Normal slope mode
2. Local wake-up via a negative edge at pin NWAKE
In the normal slope mode the transceiver is able to
transmit and receive data via the LIN bus line. The receiver
detects the data stream at the LIN bus input pin and
transfers it via pin RXD to the microcontroller (see Fig.1):
HIGH at a recessive level and LOW at a dominant level on
the bus. The receiver has a supply voltage related
threshold with hysteresis and an integrated filter to
suppress bus line noise. The transmit data stream of the
protocol controller at the TXD input is converted by the
transmitter into a bus signal with controlled slew rate and
wave shaping to minimize EME. The LIN bus output pin is
pulled HIGH via an internal slave termination resistor. For
a master application an external resistor in series with a
diode should be connected between pin INH or BAT on
one side and pin LIN on the other side (see Fig.7).
3. Mode change (pin NSLP is HIGH) from sleep mode to
normal slope/low slope mode.
Remote and local wake-up
A falling edge at pin NWAKE followed by a LOW level
maintained for a certain time period (tNWAKE) results in a
local wake-up. The pin NWAKE provides an internal
pull-up towards pin BAT. In order to prevent EMI issues, it
is recommended to connect an unused pin NWAKE to
pin BAT.
If, during power-up, pin NWAKE is LOW for a certain
period of time (tNWAKE) this will also result in a local
wake-up.
A falling edge at pin LIN followed by a LOW level
maintained for a certain time period (tBUS) and a rising
edge at pin LIN respectively (see Fig.4) results in a remote
wake-up.
Being in the sleep or standby mode, the TJA1020 enters
normal slope mode whenever a HIGH level on pin NSLP is
maintained for a time of at least tgotonorm provided its
preceding positive edge is executed while pin TXD is
already set to HIGH.
After a local or remote wake-up pin INH is activated (it
goes HIGH) and the internal slave termination resistor is
switched on. The wake-up request is indicated by a LOW
active wake-up request signal on pin RXD to interrupt the
microcontroller.
The TJA1020 switches to sleep mode in case of a LOW
level on pin NSLP, maintained during a certain time period
(tgotosleep) while pin TXD is already set to HIGH.
Low slope mode
The only difference between the normal slope mode and
the low slope mode is the transmitter behaviour.
2004 Jan 13
6
Philips Semiconductors
Product specification
LIN transceiver
TJA1020
Wake-up via mode transition
pin TXD exceeds the internal timer value (tdom), the
transmitter is disabled, driving the bus line into a recessive
state. The timer is reset by a positive edge on pin TXD.
It is also possible to set pin INH HIGH with a mode
transition towards normal slope/low slope mode via
pin NSLP. This is useful for applications with a
continuously powered microcontroller.
Fail-safe features
Pin TXD provides a pull-down to GND in order to force a
predefined level on input pin TXD in case the pin TXD is
unsupplied.
Wake-up source recognition
The TJA1020 can distinguish between a local wake-up
request on pin NWAKE and a remote wake-up request via
a dominant bus state. The wake-up source flag is set in
case the wake-up request was a local one. The wake-up
source can be read on pin TXD in the standby mode. If an
external pull-up resistor on pin TXD to the power supply
voltage of the microcontroller has been added a HIGH
level indicates a remote wake-up request (weak pull-down
at pin TXD) and a LOW level indicates a local wake-up
request (strong pull-down at pin TXD; much stronger than
the external pull-up resistor).
Pin NSLP provides a pull-down to GND in order to force
the transceiver into sleep mode in case the pin NSLP is
unsupplied.
Pin RXD is set floating in case of lost power supply on pin
BAT.
The current of the transmitter output stage is limited in
order to protect the transmitter against short-circuit to pins
BAT or GND.
A loss of power (pins BAT and GND) has no impact to the
bus line and the microcontroller. There are no reverse
currents from the bus. The LIN transceiver can be
disconnected from the power supply without influencing
the LIN bus.
The wake-up request flag (signalled on pin RXD) as well
as the wake-up source flag (signalled on pin TXD) are
reset immediately, if the microcontroller sets pin NSLP
HIGH.
The output driver at pin LIN is protected against
overtemperature conditions. If the junction temperature
exceeds the shutdown junction temperature Tj(sd), the
thermal protection circuit disables the output driver. The
driver is enabled again if the junction temperature has
been decreased below Tj(sd) and a recessive level is
present at pin TXD.
TXD dominant time-out function
A ‘TXD Dominant Time-out’ timer circuit prevents the bus
line from being driven to a permanent dominant state
(blocking all network communication) if pin TXD is forced
permanently LOW by a hardware and/or software
application failure. The timer is triggered by a negative
edge on pin TXD. If the duration of the LOW level on
LIN recessive
V
BAT
0.6V
BAT
V
0.4V
t
BUS
LIN
BAT
LIN dominant
ground
sleep mode
standby mode
MBL371
Fig.4 Wake-up behaviour.
7
2004 Jan 13
Philips Semiconductors
Product specification
LIN transceiver
TJA1020
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 60134); all voltages are referenced to pin GND.
SYMBOL
VBAT
VTXD, VRXD, VNSLP DC voltage on pins TXD, RXD and NSLP
PARAMETER
CONDITIONS
MIN.
−0.3
MAX.
+40
UNIT
supply voltage on pin BAT
V
−0.3
−27
−1
+7
V
VLIN
DC voltage on pin LIN
+40
+40
−
V
VNWAKE
INWAKE
DC voltage on pin NWAKE
V
current on pin NWAKE (only relevant if
VNWAKE < VGND − 0.3 V; current will flow into
pin GND)
−15
mA
VINH
DC voltage on pin INH
−0.3
−50
VBAT + 0.3
+15
V
IINH
output current at pin INH
transient voltage on pin LIN (ISO7637)
virtual junction temperature
storage temperature
mA
V
Vtrt(LIN)
Tvj
−150
−40
+100
+150
°C
°C
Tstg
−55
+150
Vesd(HBM)
electrostatic discharge voltage; human body
model
note 1
note 2
on pins NWAKE, LIN and BAT
−4
+4
kV
kV
V
on pins RXD, NSLP, TXD and INH
−2
+2
Vesd(MM)
electrostatic discharge voltage; machine
model; all pins
−200
+200
Notes
1. Equivalent to discharging a 100 pF capacitor through a 1.5 kΩ resistor.
2. Equivalent to discharging a 200 pF capacitor through a 10 Ω resistor and a 0.75 µH coil. In the event of a discharge
from pin INH to pin BAT: −150 V < Vesd(MM) < +150 V.
THERMAL CHARACTERISTICS
According to IEC60747-1.
SYMBOL
Rth(j-a)
PARAMETER
CONDITION
VALUE
UNIT
thermal resistance from junction to ambient in in free air
SO8 package
145
K/W
Rth(j-s)
thermal resistance from junction to substrate in free air
bare die
50
K/W
QUALITY SPECIFICATION
Quality specification in accordance with “AEC - Q100”.
2004 Jan 13
8
Philips Semiconductors
Product specification
LIN transceiver
TJA1020
CHARACTERISTICS
VBAT = 5 to 27 V; Tvj = −40 to +150 °C; RL(LIN-BAT) = 500 Ω; all voltages are defined with respect to ground; positive
currents flow into the IC; typical values are given at VBAT = 12 V; unless otherwise specified; notes 1 and 2.
SYMBOL
Supply
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
IBAT
supply current on
pin BAT
sleep mode
(VLIN = VBAT
NWAKE = VBAT
1
3
8
µA
;
V
;
VTXD = 0 V; VNSLP = 0 V)
standby mode; bus
100
300
400
900
1000
2000
µA
µA
recessive (VINH = VBAT
VLIN = VBAT
VNWAKE = VBAT
TXD = 0 V; VNSLP = 0 V)
;
;
;
V
standby mode; bus
dominant (VBAT = 12 V;
VINH = 12 V; VLIN = 0 V;
VNWAKE = 12 V;
V
TXD = 0 V;
VNSLP = 0 V); note 3
low slope mode; bus
recessive (VINH = VBAT
100
400
400
3.5
1000
1000
8
µA
µA
mA
;
VLIN = VBAT
VNWAKE = VBAT
TXD = 5 V; VNSLP = 5 V)
normal slope mode; bus 100
recessive (VINH = VBAT
VLIN = VBAT
VNWAKE = VBAT
;
;
V
;
;
;
VTXD = 5 V; VNSLP = 5 V)
low slope mode; bus
dominant (VBAT = 12 V;
VINH = 12 V;
1
V
NWAKE = 12 V;
VTXD = 0 V;
VNSLP = 5 V); note 3
normal slope mode; bus
dominant (VBAT = 12 V;
VINH = 12 V;
1
3.5
8
mA
VNWAKE = 12 V;
VTXD = 0 V;
VNSLP = 5 V); note 3
Pin TXD
VIH
HIGH-level input voltage
LOW-level input voltage
TXD hysteresis voltage
TXD pull-down resistor
2
−
7
V
VIL
−0.3
0.03
125
−
+0.8
0.5
800
V
Vhys
RTXD
−
V
VTXD = 5 V
350
kΩ
2004 Jan 13
9
Philips Semiconductors
Product specification
LIN transceiver
TJA1020
SYMBOL
PARAMETER
LOW-level input current
LOW-level output current standby mode;
CONDITIONS
MIN.
TYP.
MAX.
UNIT
µA
IIL
VTXD = 0 V
−5
0
3
+5
IOL
1.5
−
mA
(local wake-up request)
VNWAKE = 0 V;
LIN = VBAT
VTXD = 0.4 V
V
;
Pin NSLP
VIH
HIGH-level input voltage
LOW-level input voltage
NSLP hysteresis voltage
2
−
−
−
7
V
VIL
−0.3
0.03
125
−5
+0.8
0.5
V
Vhys
RNSLP
IIL
V
NSLP pull-down resistor VNSLP = 5 V
LOW-level input current VNSLP = 0 V
350
0
800
+5
kΩ
µA
Pin RXD (open-drain)
IOL
LOW-level output current normal slope mode;
VLIN = 0 V; VRXD = 0.4 V
1.3
3.5
0
−
mA
ILH
HIGH-level leakage
current
normal slope mode;
VLIN = VBAT; VRXD = 5 V
−5
+5
µA
Pin NWAKE
VIH
VIL
IIL
HIGH-level input voltage
LOW-level input voltage
NWAKE pull-up current
V
BAT − 1
−
VBAT + 0.3
V
−0.3
−30
−5
−
V
BAT − 3.3
V
VNWAKE = 0 V
−10
0
−3
µA
µA
ILH
HIGH-level leakage
current
VNWAKE = 27 V;
VBAT = 27 V
+5
Pin INH
Rsw(INH)
switch-on resistance
between pins BAT and
INH
standby; low slope or
normal slope mode;
−
30
50
Ω
I
INH = −15 mA;
VBAT = 12 V
ILH
HIGH-level leakage
current
sleep mode;
VINH = 27 V; VBAT = 27 V
−5
0
+5
µA
Pin LIN
Vo(reces)
LIN recessive output
voltage
VTXD = 5 V; ILIN = 0 mA 0.9VBAT
−
VBAT
V
Vo(dom)
LIN dominant output
voltage
VTXD = 0 V; VBAT = 7.3 V
−
−
−
1.2
V
V
VTXD = 0 V; VBAT = 7.3;
0.6
−
RL = 1 kΩ
VTXD = 0 V; VBAT = 18 V
−
−
−
2.0
V
V
VTXD = 0 V; VBAT = 18 V; 0.8
−
RL = 1 kΩ
ILH
IIL
HIGH-level leakage
current
VLIN = VBAT
−1
0
+1
µA
µA
LIN pull-up current
sleep mode; VLIN = 0 V; −2
−5
−10
VNSLP = 0 V
2004 Jan 13
10
Philips Semiconductors
Product specification
LIN transceiver
TJA1020
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
RSLAVE
slave termination
resistance to pin BAT
standby, low slope or
normal slope mode;
20
30
47
60
kΩ
V
LIN = 0 V; VBAT = 12 V
Io(sc)
short-circuit output
current
VLIN = VBAT = 12 V;
VTXD = 0 V; t < tdom
27
60
40
90
−
mA
mA
V
VLIN = VBAT = 27 V;
VTXD = 0 V; t < tdom
125
Vth(rx)
receiver threshold
voltage
VBAT = 7.3 to 27 V
0.4VBAT
0.6VBAT
0.525VBAT
Vcntr(rx)
Vthr(hys)
receiver centre voltage
VBAT = 7.3 to 27 V
VBAT = 7.3 to 27 V
0.475VBAT 0.5VBAT
V
V
receiver threshold
hysteresis voltage
0.145VBAT 0.16VBAT 0.175VBAT
Thermal shutdown
Tj(sd) shutdown junction
temperature
160
175
0
190
+2
°C
µs
AC characteristics
∆td(TXD-BUSon/off) TXD propagation delay
normal slope mode;
CL = 10 nF; RL = 500 Ω;
(see Fig.5)
−2
failure
t
PropTxDom − tPropTxRec
∆td(TXD-BUSon/off) TXD propagation delay
low slope mode;
CL = 10 nF; RL = 500 Ω;
(see Fig.5)
−5
0
0
+5
+2
µs
µs
failure
t
PropTxDom − tPropTxRec
∆td(BUSon/off-RXD) RXD propagation delay
normal slope mode and −2
low slope mode; CL = 0;
RL = ∞; voltage on LIN
externally forced; LIN
slope time <500 ns;
CRXD = 20 pF;
failure
RRXD = 2.4 kΩ; (see
Fig.5)
t
PropRxDom − tPropRxRec
tf(slope)(dom)
fall time LIN
(100% to 0%)
normal slope mode;
CL = 10 nF; RL = 500 Ω;
VBAT = 12 V; transition
from recessive to
dominant; note 4 (see
Fig.5)
−
−
16
16
27
27
µs
µs
tr(slope)(rec)
rise time LIN
(0% to 100%)
normal slope mode;
CL = 10 nF; RL = 500 Ω;
VBAT = 12 V; transition
from dominant to
recessive; note 5 (see
Fig.5)
2004 Jan 13
11
Philips Semiconductors
Product specification
LIN transceiver
TJA1020
SYMBOL
PARAMETER
normal slope symmetry
CONDITIONS
MIN.
TYP.
MAX.
UNIT
∆tslope(norm)
normal slope mode;
−5
0
+5
µs
CL = 10 nF; RL = 500 Ω;
V
BAT = 12 V;
f(slope)(dom) − tr(slope)(rec)
tf(slope)(norm)(dom) normal slope fall time LIN normal slope mode;
t
−
12
22.5
22.5
+4
µs
µs
µs
(100% to 0%)
CL = 6.8 nF;RL = 660 Ω;
VBAT = 12 V; transition
from recessive to
dominant; note 4
tr(slope)(norm)(rec)
normal slope rise time
LIN (0% to 100%)
normal slope mode;
CL = 6.8 nF;RL = 660 Ω;
VBAT = 12 V; transition
from dominant to
−
12
0
recessive; note 5
∆tslope(norm)
normal slope symmetry
normal slope mode;
CL = 6.8 nF;RL = 660 Ω;
VBAT = 12 V;
−4
t
f(slope)(dom) − tr(slope)(rec)
tf(slope)(low)(dom)
low slope fall time LIN
(100% to 0%)
low slope mode;
CL = 10 nF; RL = 500 Ω;
−
−
30
30
62
62
µs
µs
V
BAT = 12 V; note 4
tr(slope)(low)(rec)
low slope rise time LIN
(0% to 100%)
low slope mode;
CL = 10 nF; RL = 500 Ω;
VBAT = 12 V; note 5
tBUS
dominant time for
wake-up via bus
sleep mode
30
7
70
20
5
150
50
µs
µs
µs
tNWAKE
tgotonorm
dominant time for
wake-up via pin NWAKE
sleep mode
time period for mode
change from sleep or
standby mode into
2
10
normal/low slope mode
tgotosleep
time period for mode
change from normal/low
slope mode into sleep
mode
2
6
5
10
20
µs
tdom
TXD dominant time out
VTXD = 0 V
12
ms
2004 Jan 13
12
Philips Semiconductors
Product specification
LIN transceiver
TJA1020
Notes
1. All parameters are guaranteed over the virtual junction temperature by design, but only 100% tested at 125 °C
ambient temperature for dies on wafer level and, in addition to this, 100% tested at 25 °C ambient temperature for
cased products, unless otherwise specified.
2. For bare die, all parameters are only guaranteed if the backside of the bare die is connected to ground.
3. If VBAT is higher than 12 V, the battery current increases due to the internal LIN termination resistor. The minimum
VBAT – 12 V
-------------------------------
20 kΩ
value of this resistor is 20 kΩ. The maximum current increase is therefore: IBAT(increase)
=
(tVLIN = 40%) – (tVLIN = 95%)
4. tf(slope)(dom)
=
; see Fig.6.
--------------------------------------------------------------------------------
0.55
(tVLIN = 60%) – (tVLIN = 5%)
5. tr(slope)(rec)
=
; see Fig.6.
----------------------------------------------------------------------------
0.55
TIMING DIAGRAMS
TXD
V
50%
50%
t
t
PropTxRec
PropTxDom
LIN
100%
95%
0.5 V
0.5 V
BAT
BAT
5%
0%
t
t
t
PropRxRec
50%
PropRxDom
50%
RXD
MGW323
Fig.5 Timing diagram for AC characteristics, bus loaded.
2004 Jan 13
13
Philips Semiconductors
Product specification
LIN transceiver
TJA1020
V
LIN
100%
95%
60%
40%
5%
0%
t
t
slope(Rec)
t
slope(Dom)
MGU433
Fig.6 Definition of slope timing.
APPLICATION INFORMATION
ECU
BATTERY
LIN BUS
LINE
+5 V/
+3.3 V
only for
master node
INH
BAT
3
8
7
V
DD
NWAKE
RXD
1
RX0
1 kΩ
MICROCONTROLLER
TX0
TXD
TJA1020T
4
2
NSLP
LIN
6
Px.x
(1)
GND
5
GND
MGU244
More information is available in a separate application note.
(1) Cmaster = 1 nF; Cslave = 220 pF.
Fig.7 Typical application of the TJA1020.
14
2004 Jan 13
Philips Semiconductors
Product specification
LIN transceiver
TJA1020
100 nF
BAT
NWAKE
NSLP
INH
LIN
R
C
L
L
TJA1020
TXD
RXD
GND
MGT992
R
C
RXD
RXD
Fig.8 Test circuit for AC characteristics.
5 V
10 µF
10
kΩ
10
kΩ
BAT
INH
NWAKE
RXD
TJA1020
TXD
500 Ω
1 nF
LIN
5 V
NSLP
TRANSIENT
GENERATOR
GND
MGT993
The waveforms of the applied transients on pin 6 (LIN) and pin 7 (BAT) are according to ISO7637 part 1, test pulses 1, 2, 3a, 3b, 4, 5, 6 and 7.
Fig.9 Test circuit for automotive transients.
2004 Jan 13
15
Philips Semiconductors
Product specification
LIN transceiver
TJA1020
BONDING PAD LOCATIONS
1
2
8
7
y
x
3
6
5A 5B 5C
4
0
MGW322
0
Fig.10 Bonding pad locations.
Table 2 Bonding pad locations (dimensions in µm). All x and y co-ordinates are referenced to the bottom left hand
corner of the top aluminium layer.
CO-ORDINATES
SYMBOL
PAD
x
y
RXD
1
2
111
111
1570
1395
424
134
90
NSLP
NWAKE
TXD
3
165
4
134
GND1
GND2
GND3
LIN
5A
5B
5C
6
1075
1185
1295
1318
1235
1125
90
90
419
1133
1490
BAT
7
INH
8
2004 Jan 13
16
Philips Semiconductors
Product specification
LIN transceiver
TJA1020
PACKAGE OUTLINE
SO8: plastic small outline package; 8 leads; body width 3.9 mm
SOT96-1
D
E
A
X
v
c
y
H
M
A
E
Z
5
8
Q
A
2
A
(A )
3
A
1
pin 1 index
θ
L
p
L
1
4
e
w
M
detail X
b
p
0
2.5
5 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
A
(1)
(1)
(2)
UNIT
A
A
A
b
c
D
E
e
H
L
L
p
Q
v
w
y
Z
θ
1
2
3
p
E
max.
0.25
0.10
1.45
1.25
0.49
0.36
0.25
0.19
5.0
4.8
4.0
3.8
6.2
5.8
1.0
0.4
0.7
0.6
0.7
0.3
mm
1.27
0.05
1.05
0.041
1.75
0.25
0.01
0.25
0.01
0.25
0.1
8o
0o
0.010 0.057
0.004 0.049
0.019 0.0100 0.20
0.014 0.0075 0.19
0.16
0.15
0.244
0.228
0.039 0.028
0.016 0.024
0.028
0.012
inches 0.069
0.01 0.004
Notes
1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included.
2. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
JEITA
99-12-27
03-02-18
SOT96-1
076E03
MS-012
2004 Jan 13
17
Philips Semiconductors
Product specification
LIN transceiver
TJA1020
SOLDERING
To overcome these problems the double-wave soldering
method was specifically developed.
Introduction to soldering surface mount packages
If wave soldering is used the following conditions must be
observed for optimal results:
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
• Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering can still be used for
certain surface mount ICs, but it is not suitable for fine pitch
SMDs. In these situations reflow soldering is
recommended.
• For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is preferred to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must be parallel to the transport direction of the
printed-circuit board.
Reflow soldering
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Driven by legislation and environmental forces the
The footprint must incorporate solder thieves at the
downstream end.
• For packages with leads on four sides, the footprint must
be placed at a 45° angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
worldwide use of lead-free solder pastes is increasing.
Several methods exist for reflowing; for example,
convection or convection/infrared heating in a conveyor
type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending
on heating method.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical reflow peak temperatures range from
215 to 270 °C depending on solder paste material. The
top-surface temperature of the packages should
preferably be kept:
Typical dwell time of the leads in the wave ranges from
3 to 4 seconds at 250 °C or 265 °C, depending on solder
material applied, SnPb or Pb-free respectively.
• below 225 °C (SnPb process) or below 245 °C (Pb-free
process)
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
– for all BGA, HTSSON-T and SSOP-T packages
Manual soldering
– for packages with a thickness ≥ 2.5 mm
– for packages with a thickness < 2.5 mm and a
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300 °C.
volume ≥ 350 mm3 so called thick/large packages
• below 240 °C (SnPb process) or below 260 °C (Pb-free
process) for packages with a thickness < 2.5 mm and a
volume < 350 mm3 so called small/thin packages.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320 °C.
Moisture sensitivity precautions, as indicated on packing,
must be respected at all times.
Wave soldering
Conventional single wave soldering is not recommended
for surface mount devices (SMDs) or printed-circuit boards
with a high component density, as solder bridging and
non-wetting can present major problems.
2004 Jan 13
18
Philips Semiconductors
Product specification
LIN transceiver
TJA1020
Suitability of surface mount IC packages for wave and reflow soldering methods
SOLDERING METHOD
PACKAGE(1)
WAVE
not suitable
REFLOW(2)
BGA, HTSSON..T(3), LBGA, LFBGA, SQFP, SSOP..T(3), TFBGA,
USON, VFBGA
suitable
DHVQFN, HBCC, HBGA, HLQFP, HSO, HSOP, HSQFP, HSSON,
HTQFP, HTSSOP, HVQFN, HVSON, SMS
PLCC(5), SO, SOJ
not suitable(4)
suitable
suitable
suitable
LQFP, QFP, TQFP
not recommended(5)(6) suitable
SSOP, TSSOP, VSO, VSSOP
CWQCCN..L(8), PMFP(9), WQCCN..L(8)
not recommended(7)
suitable
not suitable
not suitable
Notes
1. For more detailed information on the BGA packages refer to the “(LF)BGA Application Note” (AN01026); order a copy
from your Philips Semiconductors sales office.
2. All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum
temperature (with respect to time) and body size of the package, there is a risk that internal or external package
cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). For details, refer to the
Drypack information in the “Data Handbook IC26; Integrated Circuit Packages; Section: Packing Methods”.
3. These transparent plastic packages are extremely sensitive to reflow soldering conditions and must on no account
be processed through more than one soldering cycle or subjected to infrared reflow soldering with peak temperature
exceeding 217 °C ± 10 °C measured in the atmosphere of the reflow oven. The package body peak temperature
must be kept as low as possible.
4. These packages are not suitable for wave soldering. On versions with the heatsink on the bottom side, the solder
cannot penetrate between the printed-circuit board and the heatsink. On versions with the heatsink on the top side,
the solder might be deposited on the heatsink surface.
5. If wave soldering is considered, then the package must be placed at a 45° angle to the solder wave direction.
The package footprint must incorporate solder thieves downstream and at the side corners.
6. Wave soldering is suitable for LQFP, TQFP and QFP packages with a pitch (e) larger than 0.8 mm; it is definitely not
suitable for packages with a pitch (e) equal to or smaller than 0.65 mm.
7. Wave soldering is suitable for SSOP, TSSOP, VSO and VSSOP packages with a pitch (e) equal to or larger than
0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm.
8. Image sensor packages in principle should not be soldered. They are mounted in sockets or delivered pre-mounted
on flex foil. However, the image sensor package can be mounted by the client on a flex foil by using a hot bar
soldering process. The appropriate soldering profile can be provided on request.
9. Hot bar or manual soldering is suitable for PMFP packages.
2004 Jan 13
19
Philips Semiconductors
Product specification
LIN transceiver
TJA1020
DATA SHEET STATUS
DATA SHEET
LEVEL
PRODUCT
STATUS(2)(3)
DEFINITION
STATUS(1)
I
Objective data
Development This data sheet contains data from the objective specification for product
development. Philips Semiconductors reserves the right to change the
specification in any manner without notice.
II
Preliminary data Qualification
This data sheet contains data from the preliminary specification.
Supplementary data will be published at a later date. Philips
Semiconductors reserves the right to change the specification without
notice, in order to improve the design and supply the best possible
product.
III
Product data
Production
This data sheet contains data from the product specification. Philips
Semiconductors reserves the right to make changes at any time in order
to improve the design, manufacturing and supply. Relevant changes will
be communicated via a Customer Product/Process Change Notification
(CPCN).
Notes
1. Please consult the most recently issued data sheet before initiating or completing a design.
2. The product status of the device(s) described in this data sheet may have changed since this data sheet was
published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com.
3. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.
REVISION HISTORY
REV
DATE
CPCN
DESCRIPTION
Product specification (9397 750 11718)
Modifications:
5
2004 01 13
200312021
• Chapter “Features”; ‘Supports K-line like functions’ added
• Figure 1; direction arrow on pin TXD added to indicate an output signal
flow as well as an input signal flow.
• Figure 3; conditions on mode transitions defined more accurately
• Chapter “Thermal characteristics”; Rth(j-s) value in free air = 50 K/W
added (was tbf)
• Recommendation to connect an unused pin NWAKE to pin BAT
incorporated in order to prevent EMI issues
• Specification of LIN dominant output voltage changed to align with
LIN specification 1.3
• Editorial improvements.
4
20020717
−
Product specification (9397 750 10028)
2004 Jan 13
20
Philips Semiconductors
Product specification
LIN transceiver
TJA1020
DEFINITIONS
Right to make changes
Philips Semiconductors
reserves the right to make changes in the products -
including circuits, standard cells, and/or software -
described or contained herein in order to improve design
and/or performance. When the product is in full production
(status ‘Production’), relevant changes will be
Short-form specification
The data in a short-form
specification is extracted from a full data sheet with the
same type number and title. For detailed information see
the relevant data sheet or data handbook.
Limiting values definition Limiting values given are in
accordance with the Absolute Maximum Rating System
(IEC 60134). Stress above one or more of the limiting
values may cause permanent damage to the device.
These are stress ratings only and operation of the device
at these or at any other conditions above those given in the
Characteristics sections of the specification is not implied.
Exposure to limiting values for extended periods may
affect device reliability.
communicated via a Customer Product/Process Change
Notification (CPCN). Philips Semiconductors assumes no
responsibility or liability for the use of any of these
products, conveys no licence or title under any patent,
copyright, or mask work right to these products, and
makes no representations or warranties that these
products are free from patent, copyright, or mask work
right infringement, unless otherwise specified.
Bare die
All die are tested and are guaranteed to
Application information
Applications that are
comply with all data sheet limits up to the point of wafer
sawing for a period of ninety (90) days from the date of
Philips' delivery. If there are data sheet limits not
guaranteed, these will be separately indicated in the data
sheet. There are no post packing tests performed on
individual die or wafer. Philips Semiconductors has no
control of third party procedures in the sawing, handling,
packing or assembly of the die. Accordingly, Philips
Semiconductors assumes no liability for device
described herein for any of these products are for
illustrative purposes only. Philips Semiconductors make
no representation or warranty that such applications will be
suitable for the specified use without further testing or
modification.
DISCLAIMERS
Life support applications
These products are not
functionality or performance of the die or systems after
third party sawing, handling, packing or assembly of the
die. It is the responsibility of the customer to test and
qualify their application in which the die is used.
designed for use in life support appliances, devices, or
systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips
Semiconductors customers using or selling these products
for use in such applications do so at their own risk and
agree to fully indemnify Philips Semiconductors for any
damages resulting from such application.
2004 Jan 13
21
Philips Semiconductors – a worldwide company
Contact information
For additional information please visit http://www.semiconductors.philips.com.
Fax: +31 40 27 24825
For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com.
© Koninklijke Philips Electronics N.V. 2004
SCA76
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
R16/05/pp22
Date of release: 2004 Jan 13
Document order number: 9397 750 11718
相关型号：
935286747125
LVC/LCX/Z SERIES, DUAL 1-BIT DRIVER, TRUE OUTPUT, PDSO8, 3 X 2 MM, 0.50 MM HEIGHT, 0.50 MM PITCH, PLASTIC, SOT996-2, SON-8
NXP
935286774125
AVC SERIES, 2-BIT TRANSCEIVER, TRUE OUTPUT, PDSO8, 3 MM, 0.50 MM HEIGHT, PLASTIC, SOT505-2, TSSOP-8
NXP
935286841125
AUP/ULP/V SERIES, DUAL 2-INPUT NAND GATE, PDSO8, 3 X 2 MM, 0.50 MM HEIGHT, 0.50 MM PITCH, PLASTIC, SOT996-2, SON-8
NXP
935286853125
LVC/LCX/Z SERIES, DUAL 2-INPUT NOR GATE, PDSO8, 3 X 2 MM, 0.50 MM HEIGHT, 0.50 MM PITCH, PLASTIC, SOT996-2, SON-8
NXP
935286861125
LVC/LCX/Z SERIES, TRIPLE 1-INPUT INVERT GATE, PDSO8, 3 X 2 MM, 0.50 MM HEIGHT, 0.50 MM PITCH, PLASTIC, SOT996-2, SON-8
NXP
935286881118
LED DISPLAY DRIVER, PDSO8, 3 X 3 MM, 0.85 MM HEIGHT, PLASTIC, MO-229, SOT-908-1, HVSON-8
NXP
©2020 ICPDF网 联系我们和版权申明