MCZ34701EW [NXP]
1.5 A SWITCHING REGULATOR, 400 kHz SWITCHING FREQ-MAX, PDSO32, 0.65 MM PITCH, LEAD FREE, SOIC-32;型号: | MCZ34701EW |
厂家: | NXP |
描述: | 1.5 A SWITCHING REGULATOR, 400 kHz SWITCHING FREQ-MAX, PDSO32, 0.65 MM PITCH, LEAD FREE, SOIC-32 开关 光电二极管 |
文件: | 总39页 (文件大小:819K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Document Number: MC34701
Rev 7.0, 8/2007
escale Semiconductor
Technical Data
1.5A Switch-Mode Power
Supply with Linear Regulator
34701
The 34701 provides the means to efficiently supply the Freescale
Power QUICC™ I, II, and other families of Freescale
microprocessors and DSPs. The 34701 incorporates a high
performance switching regulator, providing the direct supply for the
microprocessor’s core, and a low dropout (LDO) linear regulator
control circuit provides the microprocessor I/O and bus voltage.
POWER SUPPLY
The switching regulator is a high-efficiency synchronous buck
regulator with integrated N-channel power MOSFETs to provide
protection features and to allow space-efficient, compact design.
The 34701 incorporates many advanced features; e.g., precisely
maintained up/down power sequencing, ensuring the proper
operation and protection of the CPU and power system.
Features
EW (Pb-FREE) SUFFIX
98AARH99137A
• Operating voltage from 2.8V to 6.0V
• High-accuracy output voltages
32-PIN SOICW
• Fast transient response
• Switcher output current up to 1.5A
• Under-voltage lockout and overcurrent protection
• Enable inputs and programmable watchdog timer
• Voltage margining via I2C™ bus
• Reset with programmable power-ON delay
• Pb-free packaging designated by suffix code EW
ORDERING INFORMATION
Temperature
Package
Device
Range (T )
A
MCZ34701EW/R2
-40 to 85°C
32 SOICW
I2C is a trademark of Philips Corporation.
2.8 V to 6.0 V Input
34701
Other
Circuits
VIN2
VIN1
VBD
VBST
LDRV
CS
Adjustable:
0.8 V to VIN -
Dropout
LDO
LFB
VDDH (I/Os)
RT
ADDR
MPC8xxx
SDA
SCL
PORESET
RST
GND
Adjustable:
0.8 V to VIN -
Dropout
VBST
BOOT
SW
EN1
VDDL (Core)
EN2
VOUT
CLKSYN
PGND
CLKSEL
FREQ
INV
Optional
VDDI
Figure 1. 34701 Simplified Application Diagram
Freescale Semiconductor, Inc. reserves the right to change the detail specifications,
as may be required, to permit improvements in the design of its products.
© Freescale Semiconductor, Inc., 2007. All rights reserved.
RNAL BLOCK DIAGRAM
INTERNAL BLOCK DIAGRAM
VIN1
VIN
VDDI
Internal
VDDI
Supply
VDDI
8.0 V
VBST
VBST
VBST
Power
Enable
-
LDRV
CS
V
REF
+
To Reset
Control
VDDI
Linear
Regulator
Control
VDDI
VBD
Q5
LDO
Bandgap
Voltage
Reference
Boost
Control
V
REF
I
V
Lim
REF
V
REF
LFB
VDDI
LCMP
Power
Seq
VLDO
EN1
EN2
Q4
Power
Sequencing
Power
Down
UVLO
VBST
VBST
Voltage Margining
Watchdog Timer
Reset
RST
VOUT
Reset
Control
BOOT
Q6
SysCon
Current Limit
VDDI
POR
Timer
VIN2
(2)
INV
LFB
I2C
Control
RT
Buck
HS
Q1
I2C
Control
and
LS
Driver
SysCon
SoftSt
Thermal
Limit
Buck
Control
Logic
SW
(2)
Q2
ADDR
I2C
Interface
PGND
(2)
SDA
SCL
To Reset
Control
Error
Amp
PWM
Comp
0.8 V
Switcher
Oscillator
300 kHz
+
+
-
INV
-
VOUT
Ramp
Gen.
VOUT
Power
Seq
Q3
(4)
GND
CLKSEL
CLKSYN
FREQ
Figure 2. 34701 Simplified Internal Block Diagram
34701
Analog Integrated Circuit Device Data
2
Freescale Semiconductor
PIN CONNECTIONS
PIN CONNECTIONS
FREQ
INV
VOUT
VIN2
VIN2
SW
1
CLKSYN
CLKSEL
RST
RT
EN2
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
2
3
4
5
6
EN1
7
SW
ADDR
GND
GND
VDD1
VIN1
LDRV
CS
LDO
LFB
LCMP
8
GND
GND
PGND
PGND
VBD
VBST
BOOT
SDA
9
10
11
12
13
14
15
16
SCL
Figure 3. Pin Connections
Table 1. Pin Function Description
A functional description of each pin can be found in the FUNCTIONAL PIN DESCRIPTION section beginning on page 16.
Pin
Pin Name
Formal Name
Definition
1
FREQ
Oscillator Frequency
This switcher frequency selection pin can be adjusted by connecting external
resistor RF to the FREQ pin. The default switching frequency (FREQ pin left open or
tied to VDDI) is set to 300kHz.
2
3
INV
Inverting Input
Output Voltage
Buck controller error amplifier inverting input.
VOUT
Output voltage of the buck converter. Input pin of the switching regulator power
sequence control circuit.
4, 5
6, 7
VIN2
SW
Input Voltage 2
Switch
Buck regulator power input. Drain of the high side power MOSFET.
Buck regulator switching node. This pin is connected to the inductor.
Analog ground of the IC, thermal heatsinking.
8, 9
GND
Ground
24, 25
10, 11
12
PGND
VBD
Power Ground
Boost Drain
Buck regulator power ground.
Drain of the internal boost regulator power MOSFET.
13
VBST
Boost Voltage
Internal boost regulator output voltage. The internal boost regulator provides a 20mA
output current to supply the drive circuits for the integrated power MOSFETs and the
external N-channel power MOSFET of the linear regulator. The voltage at the VBST
pin is 7.75V (nominal).
14
15
16
17
18
19
BOOT
SDA
SCL
Bootstrap
Serial Data
Bootstrap capacitor input.
I2C bus pin. Serial data.
Serial Clock
I2C bus pin. Serial clock.
LCMP
LFB
Linear Compensation
Linear Feedback
Linear Regulator
Linear regulator compensation pin.
Linear regulator feedback pin.
LDO
Input pin of the linear regulator power sequence control circuit.
34701
Analog Integrated Circuit Device Data
Freescale Semiconductor
3
CONNECTIONS
Table 1. Pin Function Description (continued)
A functional description of each pin can be found in the FUNCTIONAL PIN DESCRIPTION section beginning on page 16.
Pin
Pin Name
Formal Name
Definition
20
CS
Current Sense
Current sense pin of the LDO. Over-current protection of the linear regulator external
power MOSFET. The voltage drop over the LDO current sense resistor RS is sensed
between the CS and LDO pins. The LDO current limit can be adjusted by selecting
the proper value of the current sensing resistor RS.
21
22
LDRV
VIN1
Linear Drive
LDO gate drive of the external pass N-channel MOSFET.
Input Voltage 1
The input supply pin for the integrated circuit. The internal circuits of the IC are
supplied through this pin.
23
26
27
28
29
30
VDDI
ADDR
EN1
EN2
RT
Power Supply
Address
Internal supply voltage. A ceramic low ESR 1uF 6V X5R or X7R capacitor is
recommended.
I2C address selection. This pin can either be left open, tied to VDDI, or grounded
through a 10k resistor.
Enable 1
Enable 1 Input. The combination of the logic state of the Enable 1 and Enable 2
inputs determines operation mode and type of power sequencing of the IC.
Enable 2
Enable 2 Input. The combination of the logic state of the Enable 1 and Enable 2
inputs determines operation mode and type of power sequencing of the IC.
Reset Timer
This pin allows programming of the power-ON reset delay by means of an external
RC network.
RST
Reset Output
(Active LOW)
The reset control circuit monitors both the switching regulator and the LDO feedback
voltages. It is an open drain output and has to be pulled up to some supply voltage
(e.g., the output of the LDO) by an external resistor.
31
32
CLKSEL
CLKSYN
Clock Selection
This pin sets the CLKSYN pin as either an oscillator output or a synchronization input
pin. The CLKSEL pin is also used for the I2C address selection.
Clock Synchronization
Oscillator output/synchronization input pin.
34701
Analog Integrated Circuit Device Data
4
Freescale Semiconductor
ELECTRICAL CHARACTERISTICS
MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
MAXIMUM RATINGS
Table 2. Maximum Ratings
All voltages are with respect to ground unless otherwise noted. Exceeding these ratings may cause a malfunction or permanent
damage to the device.
Rating
Symbol
Value
Unit
ELECTRICAL RATINGS
Supply Voltage
V
V
, V
-0.3 to 7.0
-1.0 to 7.0
-0.3 to 8.5
-0.3 to 8.5
-0.3 to 9.5
-0.3 to 7.0
-0.3 to 7.0
-0.3 to 7.0
V
V
V
V
V
V
V
V
V
IN1 IN2
Switching Node Voltage
V
SW
IN(BOOT)
Buck Regulator Bootstrap Input Voltage (BOOT - SW)
Boost Regulator Output Voltage
Boost Regulator Drain Voltage
RST Drain Voltage
V
BST
V
BD
V
RST
Enable Pin Voltage at EN1, EN2
Logic Pin Voltage at SDA, SCL
V
EN
V
LOG
Analog Pin Voltage
LDO, VOUT, RST
LDRV, LCMP, CS
-0.3 to 7.0
-0.3 to 8.5
V
OUT
V
LIN
Pin Voltage at CLKSEL, ADDR, RT, FREQ, VDDI, CLKSYN, INV, LFB
-0.3 to 3.6
V
V
V
LOGIC
ESD Voltage(1)
Human Body Model
Machine Model
±2000
±200
V
ESD
Notes
1. ESD1 testing is performed in accordance with the Human Body Model (CZAP=100 pF, RZAP=1500 ), ESD2 testing is performed in
accordance with the Machine Model (CZAP=200 pF, RZAP=0 ), and the Charge Device Model.
34701
Analog Integrated Circuit Device Data
Freescale Semiconductor
5
CTRICAL CHARACTERISTICS
MAXIMUM RATINGS
Table 2. Maximum Ratings (continued)
All voltages are with respect to ground unless otherwise noted. Exceeding these ratings may cause a malfunction or permanent
damage to the device.
Rating
Symbol
Value
Unit
THERMAL RATINGS
Storage Temperature
T
-65 to 150
Note 3
C
STG
Peak Package Reflow Temperature During Reflow(2)
,
TPPRT
(3)
°C
Maximum Junction Temperature
T
125
C
JMAX
Thermal Resistance
R
C/W
JA
(5)
Junction to Ambient (Single Layer)(4)
,
70
55
(5)
Junction to Ambient (Four Layers)(4)
,
Thermal Resistance, Junction to Base(6)
R
18
C/W
JB
Operational Package Temperature (Ambient Temperature)
Notes
T
-40 to 85
°C
A
2. Pin soldering temperature limit is for 10 seconds maximum duration. Not designed for immersion soldering. Exceeding these limits may
cause malfunction or permanent damage to the device.
3. Freescale’s package reflow capability meets Pb-free requirements for JEDEC standard J-STD-020C. For Peak Package Reflow
Temperature and Moisture Sensitivity Levels (MSL),
Go to www.freescale.com, search by part number [e.g. remove prefixes/suffixes and enter the core ID to view all orderable parts. (i.e.
MC33xxxD enter 33xxx), and review parametrics.
4. Junction temperature is a function of on-chip power dissipation, package thermal resistance, mounting site (board) temperature,
ambient temperature, air flow, power dissipation of other components on the board and board thermal resistance.
5. Per JEDEC JESD51-6 with the board horizontal
6. Thermal resistance between the die and the printed circuit board per JEDEC JESD51-8. Board temperature is measured on the top
surface of the board near the package.
34701
Analog Integrated Circuit Device Data
6
Freescale Semiconductor
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 3. Static Electrical Characteristics
Characteristics noted under conditions -40°C TA 85C unless otherwise noted. Input voltages VIN1 = VIN2 = 3.3V using
the typical application circuit (see Figure 33), unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
GENERAL
Operating Voltage Range (VIN1, VIN2)
Start-up Voltage Threshold (Boost Switching)
VBST Under-voltage Lockout (VBST rising)
VBST Under-voltage Lockout Hysteresis
V
2.8
–
–
1.6
–
6.0
1.8
6.5
1.5
–
V
V
IN
V
ST
V
5.5
0.5
–
V
BST_UVLO
BST_UVLO_HYS
V
–
V
Input DC Supply Current (Normal Operation Mode, Enabled), Unloaded
Outputs
I
60
mA
IN
VIN1 Pin Input Supply Current (EN1 = EN2 = 0)
VIN2 Pin Input Leakage Current (EN1 = EN2 = 0)
VDDI Internal Supply Voltage
I
–
–
10
100
–
–
–
mA
A
V
IN1
I
IN2
V
2.9
–
3.3
-10
DDI
DDI
VDDI Maximum Output Current (Externally Loaded)
BUCK CONVERTER
I
–
mA
Buck Converter Feedback Voltage(7), (8)
V
V
INV
IVOUT = 15mA to 1.5A. Includes Load Regulation Error
0.784
–
0.800
1.0
–
0.816
–
Buck Converter Voltage Margining Step Size
V
%
%
%
%
MVO
Buck Converter Voltage Margining Highest Positive Value
Buck Converter Voltage Margining Lowest Negative Value
V
5.9
7.9
MP
MN
V
-7.9
–
-5.9
Buck Converter Line Regulation(7), (8)
REG
LNVO
VIN1 = VIN2 = 2.8V to 6.0V, IVOUT = 15mA to 1.5A
-1.0
-1.0
–
–
1.0
1.0
Buck Converter Load Regulation(7), (8)
REG
%
mA
µA
LDVO
VIN1 = VIN2 = 2.8V to 6.0V, IVOUT = 15mA to 1.5A
VOUT Input Leakage Current
VOUT = 5.25V
I
INVOUT
–
3.5
–
–
INV Input Leakage Current
INV = 0.8V
I
-1.0
1.0
ININV
Notes
7. Design information only. This parameter is not production tested.
8. IVOUT refers to load current on output switcher.
34701
Analog Integrated Circuit Device Data
Freescale Semiconductor
7
CTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 3. Static Electrical Characteristics (continued)
Characteristics noted under conditions -40°C TA 85C unless otherwise noted. Input voltages VIN1 = VIN2 = 3.3V using
the typical application circuit (see Figure 33), unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
BUCK CONVERTER (CONTINUED)
High Side Power MOSFET Q1 RDS(ON)(9), (10)
R
m
m
DS(ON)Q1
DS(ON)Q2
–
60
–
ID = 500mA, T = 25°C, VBST = 8.0V
A
Low Side Power MOSFET Q2 RDS(ON)(9), (10)
R
–
65
–
ID = 500mA, T = 25°C, VBST = 8.0V
A
Buck Converter Peak Current Limit (High Level)
VOUT Pull-down MOSFET Q3 Current Limit
I
-4.0
-2.7
-1.5
A
A
LIMH
I
LIMPQ3
0.75
–
2.0
T
= 25°C, VBST = 8.0V
A
(10)
VOUT Pull-down MOSFET Q3 R
ID = 1.0A, VBST = 8.0V
R
DS(ON)
DS(ON)PQ3
–
150
–
–
1.9
190
–
Thermal Shutdown (VOUT Pull-down MOSFET Q3)(9)
Thermal Shutdown Hysteresis (9)
T
170
10
°C
°C
SD
T
HYS
Notes
9. Design information only. This parameter is not production tested.
10. ID is the MOSFET drain current.
34701
Analog Integrated Circuit Device Data
8
Freescale Semiconductor
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 3. Static Electrical Characteristics (continued)
Characteristics noted under conditions -40°C TA 85C unless otherwise noted. Input voltages VIN1 = VIN2 = 3.3V using
the typical application circuit (see Figure 33), unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
ERROR AMPLIFIER (BUCK CONVERTER)
Input Impedance(11)
R
–
–
–
–
–
500
150
80
–
–
–
–
–
k
IN
Output Impedance(11)
R
OUT
DC Open Loop Gain(11)
Gain Bandwidth Product(11)
Slew Rate(11)
A
dB
VOL
GBW
35
MHz
V/s
V
200
v
SR
Output Voltage – High Level
V
V
EA_OH
VIN1 > 3.3V, IOEA = -1.0mA(11), (12)
–
2.0
–
Output Voltage – Low Level
IOEA = -1.0 mA(11), (12)
V
V
EA_OL
–
–
0.4
0.5
–
–
Oscillator Ramp(11)
V
SCRAMP
OSCILLATOR
CLKSYN Pin (open) Low Level Output Voltage
IOL = +1.0mA(13)
V
–
–
0.4
V
V
OSC_OL
CLKSYN Pin (open) High Level Output Voltage
IOH = -1.0mA(14)
V
VDDI
OSC_OH
-0.4V
–
–
CLKSYN Pin (grounded) Input Voltage Threshold
CLKSYN Pin Pull-up Resistance
V
1.2
60
–
–
–
2.0
240
–
V
k
V
OSC_IH
RPU
Frequency Adjusting Reference Voltage
BOOST REGULATOR
V
1.26
FREQ
Regulator Output Voltage
V
V
BST
IBST = 20mA, VIN1 = VIN2 = 2.8V to 6.0V
7.3
–
7.7
8.3
Power MOSFET Q5 RDS(ON)(11)
R
m
DS(ON)Q5
CBST
IBD = 500mA, T = 25°C
A
650
1000
Regulator Recommended Output Capacitor
–
–
10
–
–
F
Regulator Recommended Output Capacitor Maximum ESR
ESRCBST
100
m
Notes
11. Design information only. This parameter is not production tested.
12. IOEA Refers to Error Amplifier Output Current.
13. IOL Refers to I/O Low Level
14. IOH Refers to I/O High Level
34701
Analog Integrated Circuit Device Data
Freescale Semiconductor
9
CTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 3. Static Electrical Characteristics (continued)
Characteristics noted under conditions -40°C TA 85C unless otherwise noted. Input voltages VIN1 = VIN2 = 3.3V using
the typical application circuit (see Figure 33), unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
LINEAR REGULATOR (LDO)
LDO Feedback Voltage(16)
V
V
LFB
VIN1 = VIN2 = 2.8V to 6.0V, ILDO = 10mA to 1000mA. Includes Load
Regulation Error
0.784
–
0.800
1.0
–
0.816
–
LDO Voltage Margining Step Size
V
%
%
%
%
MLDO
LDO Voltage Margining Highest Positive Value
LDO Voltage Margining Lowest Negative Value
V
V
5.9
7.9
MP
MN
-7.9
–
-5.9
LDO Line Regulation(16)
REG
REG
V
LNVLDO
VIN1 = VIN2 = 2.8V to 6.0V, ILDO = 1000mA
-1.0
-1.0
–
–
–
1.0
1.0
–
LDO Load Regulation(16)
ILDO = 10mA to 1000mA
%
LDVLDO
LDO Ripple Rejection, Dropout Voltage(16)
VDO = 1.0V, VRIPPLE = +1.0V p-p
dB
LDO_RR
40
Sinusoidal, f = 300kHz, ILDO = 500mA(15)
LDO Maximum Dropout Voltage (VIN - VLDO), using IRL2703(16)
VLDO = 2.5V, ILDO = 1000mA
V
mV
DO
–
50
50
75
65
LDO Current Sense Comparator Threshold Voltage (VCS - VLDO)
LDO Pin Input Current, VLDO = 5.25V
V
35
mV
mA
A
CSTH
I
1.0
-1.0
-5.0
1.9
–
4.0
1.0
-2.0
LDO
LFB
LDO Feedback Input Current (LFB Pin), VLFB = 0.8V
LDO Drive Output Current (LDRV Pin), VLDRV = 0V
I
I
I
-3.3
mA
A
LDRV
CSLK
CS Pin Input Leakage Current
VCS = 5.25V
50
–
–
200
2.0
LDO Pull-down MOSFET Q4 Current Limit
I
A
LIMQ4
0.75
T
= 25°C, VBST = 8.0V (LDO Pin)
A
LDO Pull-down MOSFET Q4 RDS(ON)
ID = 1.0A, VBST = 8.0V
R
DS(ON)Q4
–
–
–
1.9
–
LDO Recommended Output Capacitance
LDO Recommended Output Capacitor ESR
Thermal Shutdown (LDO Pull-down MOSFET Q4)(15)
Thermal Shutdown Hysteresis(15)
C
10
F
m
°C
LDO
RLDO
TSD
–
5.0
170
10
–
150
–
190
–
T
°C
SDHYS
Notes
15. Design information only. This parameter is not production tested.
16. IDO refers to Load Current on External LDOFET - IRL2703 is the Intersil MOSFET.
34701
Analog Integrated Circuit Device Data
10
Freescale Semiconductor
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 3. Static Electrical Characteristics (continued)
Characteristics noted under conditions -40°C TA 85C unless otherwise noted. Input voltages VIN1 = VIN2 = 3.3V using
the typical application circuit (see Figure 33), unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
CONTROL AND SUPERVISORY CIRCUITS
Enable (EN1, EN2) Input Voltage Threshold
Enable (EN1, EN2) Pull-down Resistance
RST Low-level Output Voltage, IOL = 5.0mA
RST Leakage Current, OFF State, Pulled Up to 5.25V
RST Under-voltage Threshold on VOUT (VOUT/VOUT)(17)
RST Over-voltage Threshold on VOUT (VOUT/VOUT)(17)
RST Under-voltage Threshold on VLDO (VLDO/VLDO)(17)
RST Over-voltage Threshold on VLDO (VLDO/VLDO)(17)
RST Timer Voltage Threshold
V
R
1.0
30
–
1.5
55
–
2.0
90
V
k
V
EN-TH
EN-PD
V
0.4
10
OL
ILKG-RST
–
–
A
%
V
-14
0.5
-12
4.0
1.0
-17
-1.0
–
–
-0.5
14
OUTITH
V
–
%
OUTITH
V
–
-4.0
12
%
LDOITH
V
–
%
LDOITH
V
1.2
–
1.5
-34
1.0
100
47
V
TH-RT
RST Timer Source Current (RT pin at 0V)
RST Timer Leakage Current
IS-RT
mA
A
mV
F
V
I
–
LKG-RT
RST Timer Saturation Voltage, Reset Timer Current = 300A
Maximum Recommended Value of the Reset Timer Capacitor
CLKSEL Threshold Voltage
V
35
–
SAT-RT
C
–
t
V
1.2
60
1.2
60
150
–
1.6
120
1.6
120
170
10
2.0
240
2.0
240
190
–
THCLKS
CLKSEL Pull-up Resistance
R
S
k
V
PU-CLK
ADDR Threshold Voltage(17)
V
THADDR
PU-ADDR
ADDR Pull-up Resistance
R
k
°C
°C
Thermal Shut-down (IC sensor) (17)
T
LIM
Thermal Shut-down Hysteresis(17)
T
LIMHYS
SDA, SCL PINS I2C BUS (STANDARD)
Input Threshold Voltage (Pin SCL), Rising Edge(17)
Input Threshold Voltage (Pin SDA)
V
1.3
1.3
–
–
–
1.7
1.7
10
V
V
LTH
V
LTH
SDA, SCL Input Current, Input Voltage = 5.25V (VIN1)
SDA Low-level Output Voltage, 3.0mA Sink Current
SDA, SCL Capacitance(17)
IIN
1.0
–
A
V
V
–
0.4
10
OL
C
–
7.0
pF
INPUT
Notes
17. Design information only. This parameter is not production tested.
34701
Analog Integrated Circuit Device Data
Freescale Semiconductor
11
CTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
Table 4. DYNAMIC ELECTRICAL CHARACTERISTICS
Characteristics noted under conditions -40°C TA 85C unless otherwise noted. Input voltages VIN1 = VIN2 = 3.3V using
the typical application circuit (see Figures 33), unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
BUCK CONVERTER
Duty Cycle Range (Normal Operation)(18)
t
0.0
–
–
95
–
%
D
Switching Node SW Rise Time(18)
VIN = 5.0V, ILOAD = 1.0A
t
ns
RISE
7.0
Switching Node SW Fall Time(18)
VIN = 5.0V, ILOAD = 1.0A
t
ns
FALL
–
–
17
35
–
–
Maximum Deadtime(18)
t
ns
ns
D
Buck Control Loop Propagation Delay(18)
t
PD
VINV < 0.8V to VSW > 90% of High Level or VINV > 0.8V to VSW < 10%
of Low Level
–
50
350
10
–
Soft Start Duration (Power Sequencing Disabled, EN1 = 1, EN2 = 1)(18)
t
200
7.0
70
800
15
s
ms
ms
SS
Fault Condition Timeout(18)
Retry Timer Cycle(18)
OSCILLATOR
t
FAULT
t
100
150
RET
Oscillator Center Frequency(20)
f
270
300
330
kHz
OSC
RF = 11.3k
Oscillator Frequency Range
f
200
7.0
–
–
400
22
kHz
k
OSC
FREQ
OSC
Oscillator Frequency Adjusting Resistor Range
R
f
Oscillator Frequency Adjustment(19), (20)
kHz
RF = 7.0k
400
–
–
Oscillator Frequency Adjustment(19), (20)
f
f
kHz
OSC
RF = 22k
–
–
–
200
–
Oscillator Default Frequency (Switching Frequency), FREQ Pin Open
300
kHz
%
OSC
Oscillator Output Signal Duty Cycle (Square Wave, 180° Out-of-Phase with
the Internal Suitable Oscillator)
D
OSC
40
50
–
60
–
Synchronization Pulse Minimum Duration(18)
t
1.0
s
SYNC
Notes
18. Design information only. This parameter is not production tested.
19. see Figure 4 for more details
20. RF is RFREQ
34701
Analog Integrated Circuit Device Data
12
Freescale Semiconductor
ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
Table 4. DYNAMIC ELECTRICAL CHARACTERISTICS (continued)
Characteristics noted under conditions -40°C TA 85C unless otherwise noted. Input voltages VIN1 = VIN2 = 3.3V using
the typical application circuit (see Figures 33), unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
BOOST REGULATOR
Boost Regulator MOSFET Maximum ON Time(21)
Boost Regulator Control Loop Propagation Delay(21)
t
–
–
24
50
–
–
s
ns
ns
ON
t
BST_PD
Boost Switching Node VBD Rise Time(21)
IBST = 20mA
t
B_RISE
–
–
5.0
3.0
Boost Switching Node VBD Fall Time(21)
IBST = 20mA
t
ns
B_FALL
–
LINEAR REGULATOR (LDO)
Fault Condition Timeout
t
7.0
70
10
15
ms
ms
FAULT
Retry Timer Cycle
t
100
150
RET
RESET MONITOR (RST)
Monitoring LFB Pin Delay
Monitoring INV Pin Delay
SCA, SCL PIN, I2C BUS (STANDARD)
t
12
12
–
–
28
28
s
s
D_RST_LFB
t
D_RST_INV
SCL Clock Frequency(21)
SCL
f
–
–
–
100
–
kHz
s
Bus Free Time Between a STOP and a START Condition(21)
BUF
t
4.7
Hold Time (Repeated) START Condition (After this period, the first clock
pulse is generated.)(21)
t
s
HD-STA
4.0
4.7
4.0
–
–
–
–
–
–
Low Period of the SCL Clock(21)
High Period of the SCL Clock(21)
LOW
t
s
s
ns
t
HIGH
SDA Fall Time from VIH_MAX to VIL_MIN, Bus Capacitance 10pF to 400pF,
3.0mA Sink Current(21), (23)
t
F
–
–
–
–
–
–
–
250
–
Setup Time for a Repeated START Condition(21)
SU-STA
t
4.7
0.0
250
4.0
–
s
s
ns
s
pF
(22)
Data Hold Time for I2C Bus Devices(21)
Data Setup Time(21)
,
HD-DAT
T
t
t
–
–
SU-DA
Setup Time for STOP Condition(21)
SU-STO
CB
t
–
Capacitive Load for Each Bus Line(21)
400
Notes
21. Design information only. This parameter is not production tested.
22. The device provides an internal hold time of at least 300ns for the SDA signal (refer to the VIH_MIN of the SCL signal) to bridge the
undefined region of the falling edge of SCL.
23. VIH is high level voltage on I2C bus lines and VIL is low level voltage on I2C bus lines
34701
Analog Integrated Circuit Device Data
Freescale Semiconductor
13
CTRICAL CHARACTERISTICS
TIMING DIAGRAM
TIMING DIAGRAM
t
HD-STA
t
t
SU-STO
t
HD-STA
SU-STA
t
t
SU-DAT
HD-DAT
Figure 4. Definition of Time on the I2C Bus
ELECTRICAL PERFORMANCE CURVES
300
100
90
80
70
60
50
40
30
20
10
295
Vin=3.3V, Vout=1.2V
Vin=3.3V, Vout=1.8V
Vin=5.0V, Vout=1.2V
Vin=5.0V, Vout=1.8V
290
285
0
280
0
0,5
1
1,5
-50
50
100
Load Current [A]
0
Temperature (C°)
Figure 7. Switcher Efficiency vs. Load Current
Figure 5. fOSC vs. Temperature
450
3.00
2.80
2.60
2.40
2.20
2.00
400
350
300
250
200
150
100
-50
0
50
100
7
12
17
22
Temperature (°C)
Rf (k )
Figure 8. Switcher ILim vs. Temperature
Figure 6. fOSC vs. Rf
34701
Analog Integrated Circuit Device Data
14
Freescale Semiconductor
ELECTRICAL CHARACTERISTICS
ELECTRICAL PERFORMANCE CURVES
25
23
21
19
17
15
13
11
9
0.83
0.82
0.81
0.80
0.79
0.78
0.77
7
5
-50
0
50
100
Temperature(C°)
0
100
200
300
RT (k ) with CT = 33 nF
Figure 10. Timer (ms) vs. RT
Figure 9. VREF vs. Temperature
34701
Analog Integrated Circuit Device Data
Freescale Semiconductor
15
CTIONAL DESCRIPTION
INTRODUCTION
FUNCTIONAL DESCRIPTION
INTRODUCTION
The 34701 power supply integrated circuit provides the
means to efficiently supply the Freescale Power QUICC and
other families of Freescale microprocessors. It incorporates a
high performance synchronous buck regulator, supplying the
microprocessor’s core, and a low dropout (LDO) linear
regulator providing the microprocessor I/O and bus voltages.
This device incorporates many advanced features; e.g.,
precisely maintained up/down power sequencing, ensuring
the proper operation and protection of the CPU and power
system. At the same time, it provides high flexibility of
configuration, allowing the maximum optimization of the
power supply system.
FUNCTIONAL PIN DESCRIPTION
OSCILLATOR FREQUENCY PIN (FREQ)
BOOTSTRAP PIN (BOOT)
This switcher frequency selection pin can be adjusted by
connecting external resistor RF to the FREQ pin. The default
switching frequency (FREQ pin left open or tied to VDDI) is
set to 300kHz.
Bootstrap capacitor input.
SERIAL DATA PIN (SDA)
I2C bus pin. Serial data.
INVERTING INPUT PIN (INV)
SERIAL CLOCK PIN (SCL)
Buck Controller Error Amplifier inverting input.
I2C bus pin. Serial clock.
OUTPUT VOLTAGE PIN (VOUT)
Output voltage of the buck converter. Input pin of the
switching regulator power sequence control circuit.
LINEAR COMPENSATION PIN (LCMP)
Linear regulator compensation pin.
INPUT VOLTAGE 2 PINS (VIN2)
LINEAR FEEDBACK PIN (LFB)
Buck regulator power input. Drain of the high side power
MOSFET.
Linear regulator feedback pin.
SWITCH PINS (SW)
LINEAR REGULATOR PIN (LDO)
Buck regulator switching node. This pin is connected to the
inductor.
Input pin of the linear regulator power sequence control
circuit.
GROUND PINS (GND)
CURRENT SENSE PIN (CS)
Analog ground of the IC, thermal heatsinking.
Current sense pin of the LDO. Over-current protection of
the linear regulator external power MOSFET. The voltage
drop over the LDO current sense resistor RS is sensed
between the CS and LDO pins. The LDO current limit can be
adjusted by selecting the proper value of the current sensing
resistor RS.
POWER GROUND PINS (PGND)
Buck regulator power ground.
BOOST DRAIN PIN (VBD)
Drain of the internal boost regulator power MOSFET.
LINEAR DRIVE PIN (LDRV)
BOOST VOLTAGE PIN (VBST)
LDO gate drive of the external pass N-channel MOSFET.
Internal boost regulator output voltage. The internal boost
regulator provides a 20mA output current to supply the drive
circuits for the integrated power MOSFETs and the external
N-channel power MOSFET of the linear regulator. The
voltage at the VBST pin is 7.75V nominal.
INPUT VOLTAGE 1 PIN (VIN1)
The input supply pin for the integrated circuit. The internal
circuits of the IC are supplied through this pin.
34701
Analog Integrated Circuit Device Data
16
Freescale Semiconductor
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
POWER SUPPLY PIN (VDDI)
RESET TIMER PIN (RT)
Internal supply voltage. A ceramic low ESR 1uF 6V X5R or
X7R capacitor is recommended.
The Reset Timer power-up delay (RT) pin is used to set
the delay between the time when the LDO and switcher
outputs are active and stable and the RST output is released.
An external resistor and capacitor are used to program the
timer. The power-up delay can be obtained by using the
following formula:
ADDRESS PIN (ADDR)
The ADDR pin is used to set the address of the device
when used in an I2C communication. This pin can either be
tied to VDDI or grounded through a 10k resistor. Refer to
I2C Bus Operation on page 26 for more information on this
pin.
t
D = 10ms + RtCt
Where Rt is the Reset Timer programming resistor and Ct
is the Reset Timer programming capacitor, both connected in
parallel from RT to ground.
Note Observe the maximum Ct value and expect reduced
accuracy if Rt is less than 10k.
ENABLE 1 AND 2 PINS (EN1 AND EN2)
These two pins permit positive logic control of the Enable
function and selection of the Power Sequencing mode
concurrently. Table 5 depicts the EN1 and EN2 function and
Power Sequencing mode selection.
RESET OUTPUT PIN (RST)
The Reset Control circuit monitors both the switching
regulator and the LDO feedback voltages. It is an open drain
output and has to be pulled up to some supply voltage (e.g.,
the output of the LDO) by an external resistor.
Both EN1 and EN2 pins have internal pull-down resistors
and both can withstand a short circuit to the supply voltage,
6.0V.
The Reset Control circuit supervises both output
voltages—the linear regulator output VLDO and the switching
regulator output VOUT. When either of these two regulators
is out of regulation (high or low), the RST pin is pulled low.
There is a 20s delay filter preventing erroneous resets.
During power-up sequencing, RST is held low until the Reset
Timer times out.
Table 5. Operating Mode Selection
EN1
EN2
Operating Mode
Regulators Disabled
0
0
1
1
0
1
0
1
Standard Power Sequencing
Inverted Power Sequencing
CLOCK SELECTION PIN (CLKSEL)
No Power Sequencing,
Regulators Enabled
This pin sets the CLKSYN pin as either an oscillator output
or a synchronization input pin. The CLKSEL pin is also used
for the I2C address selection.
CLOCK SYNCHRONIZATION PIN (CLKSYN)
Oscillator output/synchronization input pin.
34701
Analog Integrated Circuit Device Data
Freescale Semiconductor
17
CTIONAL DESCRIPTION
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
incorporates many advanced features; e.g., precisely
maintained up/down power sequencing, ensuring the proper
operation and protection of the CPU and power system.
INTRODUCTION
The 34701 incorporates a high performance synchronous
buck regulator, supplying the microprocessor’s core, and a
low dropout (LDO) linear regulator providing the
microprocessor I/O and bus voltages. This device
Power Sequencing
Voltage Margining
Watchdog Timer
UVLO
Boost Regulator
Reset Control
POR Timer
Buck Control Logic
I2C Interface
VDDI
Internal
Supply
Bandgap
Buck HS and
LS Driver
Voltage
Reference
Linear Regulator
Control
Switcher
Oscillator
300kHz
Thermal Shutdown
ILIM
Figure 11. 34701 Functional Internal Block Diagram
When the inductor current falls below the valley current limit
BOOST REGULATOR
value (nominally 600mA), the low side switch is turned on
again, starting the next switching cycle. After the boost
regulator output capacitor reaches approximately 6.0 volts,
the peak and valley current limit levels are proportionally
scaled down to approximately one fifth of their original values.
When the boost regulator reaches its regulation limit (7.75V
typical), the low side switch is turned off until the output
voltage falls below the regulation limit again.
A boost regulator provides a high-voltage necessary to
properly drive the buck regulator power MOSFETs,
especially during the low input voltage condition. The LDO
regulator external N-channel MOSFET gate is also powered
from the boost regulator. In order to properly enhance the
high side MOSFETs when only a +3.3V supply rail powers
the integrated circuit, the boost regulator provides an output
voltage of 7.75V nominal value.
The higher current limit values in the beginning of the
boost regulator start-up sequence allow fast power up of the
whole IC, while the normal operation with reduced current
limit greatly reduces the switching noise and therefore
improves the overall EMC performance. See Figure 12 for
the boost regulator output voltage and inductor current
waveforms (picture not to scale).
The 34701 boost regulator uses a simple hysteretic
current control technique, which allows fast power-up and
does not require any compensation. When the boost
regulator main power switch (low side) is turned on, the
current in the inductor starts to ramp up. After the inductor
current reaches the upper current limit (nominally set at
1.0A), the low-side switch is turned off and the current
charges the output capacitor through the internal rectifier.
34701
Analog Integrated Circuit Device Data
18
Freescale Semiconductor
FUNCTIONAL DESCRIPTION
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
Fault Timer
= 10 ms
Booster Output Voltage
7.75V
t
t
= 10 ms
FAULT
FAU LT
I
Current Limit
I
pk
pk
6.0 V
0.5 I
0.5 I
pk
pk
Retry Timer
= 100 ms
t
Ret
0 A
0 V
Figure 13. Switching Regulator Current Limit
(Not To Scale)
I
= 1 A typ.
pk
To avoid destruction of the supplied circuits, the switching
regulator has a current limit with retry capability. When an
over-current condition occurs and the switch current reaches
the peak current limit value, the main (high side) switch is
turned off until the inductor current decays to the valley value,
which is one half of the peak current limit. If an over-current
condition exists for 10ms, the buck regulator control circuit
shuts the switcher OFF and the switcher retry timer starts to
time out. When the timer expires after 100ms, the switcher
engages the start-up sequence and runs for 10ms,
Booster Inductor Current
0.6 A typ.
0.2 A typ.
0.1 A typ.
repeatedly checking for the over-current condition. Figure 13
describes the switching regulator over-current condition and
current limit. During the current limited operation (e.g., in
case of short-circuit on the switching regulator output), the
switching regulator operation is not synchronized to the
oscillator frequency. Figure 14 (respectively Figure 15)
depicts the current limit with a retry capability feature of the
switcher (respectively LDO).
Figure 12. Boost Regulator Startup (Not To Scale)
SWITCHING REGULATOR
The switching regulator is a high frequency (300kHz
default, adjustable in the range from 200kHz to 400kHz),
synchronous buck converter driving integrated high side and
low side N-channel power MOSFETs. The switching
regulator output voltage is adjustable by means of an external
resistor divider to provide the required output voltage within
±2.0% accuracy, and is intended to directly power the core of
the microprocessor. The buck controller uses a PWM voltage
mode control topology with feed-forward to achieve excellent
line and load regulation.
The 34702 integrated boost regulator provides a 7.75V rail
which is used to properly bias the switcher’s MOSFET. In
addition, the boost structure has a very low start-up voltage
(Typically 1.6V), hence ensuring very low input voltage
functionality. A typical bootstrap technique is used to provide
voltage necessary to properly enhance the high side
MOSFET gate. When the regulator is supplied only from low
input voltage (e.g., single +3.3V supply rail), the bootstrap
capacitor is charged from the internal boost regulator output
VBST through an external diode. This arrangement allows
the 34701 to operate from very low input voltage and also
comply with the power sequencing requirements of the
supplied microcontroller.
Figure 14. Switching Converter Over-current Protection
34701
Analog Integrated Circuit Device Data
Freescale Semiconductor
19
CTIONAL DESCRIPTION
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
100ms, the LDO tries to power-up again for 10ms, repeatedly
checking for the over-current condition. The current limit of
the LDO can be set by using the following formula:
ILIM = 50mV/RS
Where RS is the LDO current sense resistor, connected
between the CS pin and the LDO pin output (see Figure 33
on page 34), and 50mV is the typical value of the LDO current
sense comparator threshold voltage.
When no current sense resistor is used, it is still possible
to detect the over-current condition by tying the current sense
pin CS to the VBST voltage. In this case, the over-current
condition is sensed by saturation of the linear regulator driver
buffer.
The output voltage of the LDO can be adjusted by means
of an external resistor divider connected to the feedback
control pin LFB. The linear regulator output voltage can be
adjusted in the range of 0.8V to VIN - LDO dropout voltage.
Power-up, power-down, and fault management are
coordinated with the switching regulator.
Figure 15. LDO Converter Over-current Protection
The output voltage VOUT can be adjusted by means of an
external resistor divider connected to the feedback control
pin INV. The switching regulator output voltage can be
adjusted in the range of 0.8V to VIN - buck dropout voltage.
Power-up, power-down, and fault management are
coordinated with the linear regulator.
POWER SEQUENCING VOLTAGE MARGINING
WATCHDOG TIMER
A watchdog function is available via I2C bus
communication. It is possible to select either window
watchdog or timeout watchdog operation, as illustrated in
Figure 16.
SWITCHER OSCILLATOR
Watchdog timeout starts when the watchdog function is
activated via I2C bus sending a watchdog programming
command byte, thus determining watchdog operation
(window or timeout) and period duration (refer to Table 8,
page 27). If the watchdog is cleared by receiving a new
watchdog programming command through the I2C bus, the
watchdog timer is reset and the new timeout period begins. If
the watchdog time expires, the RST will become active
(LOW) for a time determined by the RC components of the
RT timer plus 10ms. After a watchdog timeout, the function is
no longer active.
A 300kHz (default) oscillator sets the switching frequency
of the buck regulator. The frequency of the oscillator can be
adjusted between 200kHz and 400kHz by an optional
external resistor RF connected from the FREQ pin of the
integrated circuit to ground. See Figure 6 on page 14 for
frequency resistor selection.
The CLKSYN pin can be configured as either an oscillator
output when the CLKSEL pin is left open or as a
synchronization input when the CLKSEL pin is grounded.
The oscillator output signal is a square wave logic signal with
50% duty cycle, 180 degrees out-of-phase with the internal
clock signal. This allows opposite phase synchronization of
two 34702 devices.
Watchdog Closed
Window Open
for Watchdog Clear
No Watchdog Clear Allowed
When the CLKSYN pin is used as a synchronization input
(CLKSEL pin grounded), the external resistor RF chosen
from the chart in Figure 6 should be used to synchronize the
internal slope compensation ramp to the external clock.
Operation is only recommended between 200kHz and
400kHz. The supplied synchronization signal does not need
to be 50% duty cycle. Minimum pulse width is 1.0µs.
50% of Watchdog Period
Watchdog Period
Timing Selected via 12C Bus – See Table 4
Window Watchdog
Window Open for Watchdog Clear
LOW DROPOUT LINEAR REGULATOR (LDO)
The adjustable low dropout linear regulator (LDO) is
capable of supplying a 1.0A output current. It has a current
limit with retry capability. When the voltage measured across
the current sense resistor reaches the 50mV threshold, the
control circuit limits the current for 10ms. If the over-current
condition still exists, the linear regulator is turned off and the
retry timer starts to time out. When the timer expires after
Watchdog Period
Timing Selected via I2C Bus – See Table 4
Time-Out Watchdog
Figure 16. Watchdog Operation
34701
Analog Integrated Circuit Device Data
Freescale Semiconductor
20
FUNCTIONAL DESCRIPTION
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
When the window watchdog function is selected, the timer
cannot be cleared during the closed window time, which is
50% of the total watchdog period. When the watchdog is
cleared, the timer is reset and starts a new tim-out period. If
the watchdog is not cleared during the open window time, the
RST will become active (LOW) for a time determined by the
RC components of the RT timer plus 10ms.
34701
Analog Integrated Circuit Device Data
Freescale Semiconductor
21
CTIONAL DEVICE OPERATION
OPERATIONAL MODES
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
THERMAL SHUTDOWN
POWER SEQUENCING MODES
To increase the overall safety of the system designed with
the 34701, an internal thermal shutdown function has been
incorporated into the switching regulator circuit. The 34701
senses the temperature of the buck regulator main switching
MOSFET (high side MOSFET M1; see Figure 2 on page 2),
the low side (synchronous MOSFET M2), and control circuit.
If the temperature of any of the monitored components
exceeds the limit of safe operation (Thermal Shutdown), the
switching regulator and the LDO shut down. After the
temperature falls below the value given by the thermal
shutdown hysteresis window, the switcher tries again to
operate.
The power sequencing of the two outputs of this power
supply IC is in compliance with the Freescale Power QUICC
and other 32-bit microprocessor requirements. When the
input voltage is applied, the switcher and linear regulator
outputs follow the supply rail voltage during power-up and
power-down in the limits given by the microcontroller power
sequencing specification, illustrated in Figures 17 through
19. There are two possible power sequencing modes,
Standard and Inverted, as explained in more detail below.
The third mode of operation is Power Sequencing Disabled.
3.3 V Input
2.5 V
Other
Circuits
The VOUT pull-down MOSFET M3 has an independent
thermal shutdown control. If the M3 temperature exceeds the
thermal shutdown, the M3 is turned off without affecting the
switcher operation.
34701
VIN2
VIN1
VBD
VBST
LDRV
CS
3.3 V
The LDO pull-down MOSFET M4 has an independent
thermal shutdown control. If the M4 temperature exceeds the
thermal shutdown, the M4 will be turned off without affecting
the LDO operation.
LDO
LFB
VDDL (Core)
RT
ADDR
MCU
SDA
SCL
RST
GND
VBST
BOOT
SW
SOFT START
1.5 V
EN1
EN2
VDDH (I/Os)
A switching regulator soft start feature is incorporated in
the 34701. The soft start is active each time the IC is enabled,
VIN is reapplied, or after a fault retry. Other transient events
do not activate the soft start.
VOUT
CLKSYN
CLKSEL
FREQ
PGND
INV
Optional
VDDI
VOLTAGE MARGINING
The 34701 includes a voltage margining feature accessed
3.3 V Input Supply (I/O Voltage)
through the I2C bus. Voltage margining allows for
V = 2.1 V
Max. Lead
independent adjustment of the switcher VOUT voltage and
the linear output VLDO. Each can be adjusted up and down
in 1.0% steps to a range of ±7.0%. This feature allows for
worst case system validation; i.e., determining the design
margin. Margining details are described in the section entitled
I2C Bus Operation, beginning on page 26 of this datasheet.
1.8V Start-Up
Slope
1.0 V/ms
1.5 V Core Voltage
V = 2.1 V
Max. Lead
V = 0.4 V
Max. Lag
Figure 17. Standard Power-up/Down Sequence
in +3.3V Supply System
34701
Analog Integrated Circuit Device Data
22
Freescale Semiconductor
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
5.0 V Input
5.0 V Input
34701
34701
VIN2
VIN1
VIN2
VIN1
VBD
VBST
LDRV
CS
VBD
VBST
LDRV
CS
3.3 V
1.5 V
LDO
LFB
VDDL (Core)
VDDH (I/Os)
LDO
LFB
RT
RT
ADDR
ADDR
MCU
SDA
SCL
MCU
SDA
SCL
RST
RST
GND
EN1
GND
VBST
BOOT
SW
VBST
BOOT
SW
5.0 V
EN1
EN2
1.5 V
3.3 V
VDDL (Core)
VDDH (I/Os)
EN2
5.0 V
VOUT
VOUT
CLKSYN
CLKSYN
CLKSEL
FREQ
PGND
CLKSEL
FREQ
PGND
INV
INV
Optional
Optional
VDDI
VDDI
5.0 V Input Supply
V = 2.1 V
Max. Lead
V = 2.1 V
3.3 V I/O Voltage (VOUT)
5.0 V Input Supply
V = 2.1 V
Max. Lead
Max. Lead
1.8V Start-Up
V = 2.1 V
(VLDO)
1.5 V Core Voltage
3.3 V I/O Voltage (VLDO)
Max. Lead
1.8V Start-Up
1.5 V Core Voltage
(VOUT)
V = 0.4 V
V = 0.4 V
Max. Lag
Max. Lag
V = 0.4 V
V = 0.4 V
Max. Lag
Max. Lag
Figure 19. Inverted Power-up/Down Sequence in +5.0V
Supply System
Figure 18. Standard Power-up/Down Sequence
in +5.0V Supply System
ASSUMED REQUIREMENTS
1. I/O supply voltage not to exceed core voltage by more
than 2.0V.
STANDARD POWER SEQUENCING
When the power supply IC operates in the Standard Power
Sequencing Mode, the switcher output provides the core
voltage for the microprocessor. This situation and operating
conditions are illustrated in Figures 17 and 18. Table 5,
page 17, shows the Power Sequencing Mode selection.
2. Core supply voltage not to exceed I/O voltage by more
than 0.4V.
Methods of Control
The 34701 has several methods of monitoring and
controlling the regulator output voltages, as described in the
paragraphs below. Power sequencing control is also
achieved through the intrinsic operation of the regulators.
The EN1 and EN2 pins can be used to select the proper
Power Sequencing Mode required by the powered system or
to disable the power sequencing (refer to Table 5).
INVERTED POWER SEQUENCING
When the power supply IC is operating in the Inverted
Power Sequencing Mode, the linear regulator (LDO) output
provides the core voltage for the microprocessor, as
illustrated in Figure 19. Table 5 shows the Power
Sequencing Mode selection.
Intrinsic Operation
For both the LDO and switcher, whenever the output
voltage is below the regulation point, the LDO external Pass
MOSFET is on, or the buck high side MOSFET is on at a duty
cycle controlled by the switcher. Because these devices are
MOSFETs, current can flow in either direction, balancing the
voltages via the common supply pin. The ability to maintain
the MOSFETs on is dependent on the available gate voltage,
and thus the size of the boost regulator storage capacitor.
34701
Analog Integrated Circuit Device Data
Freescale Semiconductor
23
CTIONAL DEVICE OPERATION
OPERATIONAL MODES
Standard Power Sequencing Control
VOUT output voltage is less than 1.8V above the LDO
output voltage.
Comparators monitor voltage differences between the
LDO (LDO pin) and the switcher (VOUT pin) outputs as
follows:
4. VOUT < LDO + 2.0V, cancel (2)
5. VOUT < LDO - 0.2V, turn off LDO. The LDO can be
forced off. This occurs whenever the VOUT is less than
VLDO - 0.2V.
1. LDO > VOUT + 1.9V, turn off LDO. The LDO can be
forced off. This occurs whenever the LDO output
voltage exceeds the switcher output voltage by more
than 1.9V.
6. VOUT < LDO - 0.3V, turn on the 1.5 LDO sink
MOSFET. This occurs when the LDO output voltage
exceeds the VOUT output by more than 300mV.
2. LDO > VOUT + 2.0V, shunt LDO to ground. If turning
off the LDO is insufficient and the LDO output voltage
exceeds the switcher output voltage by more than
2.0V, a 1.5 shunt MOSFET is turned on that
7. VOUT < LDO - 0.2V, cancel (6).
8. VOUT < LDO - 0.1V, cancel (5). Normal operation
resumes when VOUT > LDO - 0.1V.
discharges the LDO load capacitor to ground. The
shunt MOSFET is used for switcher output shorts to
ground and for power down in case of VIN1 VIN2
with the switcher output falling faster than the LDO.
STANDARD OPERATING MODE
Single 3.3V Supply, VIN = VIN1 = VIN2 = 3.3V
3. LDO < VOUT + 1.9V cancel (2).
The 3.3V supplies the microprocessor I/O voltage, the
switcher supplies core voltage (e.g., 1.5V nominal), and the
LDO operates independently (see Figure 17, page 22).
Power sequencing depends only on the normal switcher
intrinsic operation to control the buck high side MOSFET.
4. LDO < VOUT + 1.8V, cancel (1) above, re-enable LDO.
Normal operation resumes when the LDO output
voltage is less than 1.8V above the switcher output
voltage.
5. LDO < VOUT - 0.1V, turn off switcher. The switcher
can be forced off. This occurs whenever the LDO is
less than VOUT - 0.1V.
Power-up
When VIN is rising, initially VOUT is below the regulation
point and the Buck High-Side MOSFET is on. In order not to
exceed the 2.1 V differential requirement between the I/O
(VIN) and the core (VOUT), the switcher must start up at
2.1 V or less and be able to maintain the 2.1 V or less
differential. The maximum slew rate for VIN is 1.0 V/ms.
6. LDO < VOUT - 0.3V, turn on Sync (LS) MOSFET and
1.5 VOUT sink MOSFET. The buck high side
MOSFET is forced off and the sync MOSFET is forced
on. This occurs when the switcher output voltage
exceeds the LDO output by more than 300mV.
7. LDO > VOUT - 0.3V, cancel (6).
Power-Down
8. LDO > VOUT - 0.1V, cancel (5). Normal operation
resumes when LDO < VOUT - 0.1V.
When VIN is falling, VOUT falls below the regulation point;
therefore, the buck high side MOSFET is on. In the case
where VOUT is falling faster than VIN, the buck high side
MOSFET attempts to maintain VOUT. In the case where VIN
is falling faster than VOUT, the buck high side MOSFET is
also on, and the VOUT load capacitor is discharged through
the buck high side MOSFET to VIN. Thus, provided VIN does
not fall too fast, the core voltage (VOUT) does not exceed the
I/O voltage (VIN) by more than a maximum of 0.4V.
Inverted Power Sequencing Control
Comparators monitor voltage differences between the
switcher (VOUT pin) and LDO (LDO pin) outputs as follows:
1. VOUT > LDO + 1.8V, turn off VOUT . The switcher
VOUT can be forced off. This occurs whenever the
VOUT output voltage exceeds the LDO output voltage
by more than 1.8V.
2. VOUT > LDO + 2.0V, shunt VOUT to ground. If turning
off the switcher VOUT is insufficient and the VOUT
output voltage exceeds the LDO output voltage by
more than 2.0V, a 1.5 shunt MOSFET and the
switcher synchronous MOSFET are turned on to
discharge the VOUT load capacitor to ground. The
shunt MOSFET and synchronous MOSFET are used
for LDO output shorts to ground and for power down in
case of VIN1 VIN2 with LDO output falling faster than
the VOUT.
Shorted Load
1. VOUT shorted to ground. This causes the I/O voltage
to exceed the core voltage by more than 2.1V. No load
protection.
2. VIN shorted to ground. Until the switcher load
capacitance is discharged, the core voltage exceeds
the I/O voltage by more than 0.4V. By the intrinsic
operation of the switcher, the load capacitor is
discharged rapidly through the buck high side
MOSFET to VIN.
3. VOUT < LDO + 1.8V, cancel (1) and (2) above, re-
enable VOUT. Normal operation resumes when the
3. VOUT shorted to supply. No load protection. 34701 is
protected by current limit and thermal shutdown.
34701
Analog Integrated Circuit Device Data
24
Freescale Semiconductor
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
Single 5.0V Supply, VIN1 = VIN2, or Dual Supply VIN1
VIN2
depends only on the normal LDO intrinsic operation to control
the Pass MOSFET.
The LDO supplies the microprocessor I/O voltage. The
switcher supplies the core (e.g., 1.5V nominal) (see
Figure 18, page 23).
Power-up
When VIN is rising, initially LDO is below the regulation
point and the Pass MOSFET is on. In order not to exceed the
2.1V differential requirement between the I/O (VIN) and the
core (LDO), the LDO must start up at 2.1V or less and be able
to maintain the 2.1V or less differential. The maximum slew
rate for VIN is 1.0V/ms.
Power-up
This condition depends upon the regulator current limit,
load current and capacitance, and the relative rise times of
the VIN1 and VIN2 supplies. There are two cases:
1. LDO rises faster than VOUT. The LDO uses control
methods (1) and (2) described in the section Methods
of Control on page 23.
Power-down
When VIN is falling, LDO falls below the regulation point;
therefore, the Pass MOSFET is on. In the case where LDO is
falling faster than VIN, the pass MOSFET attempts to
maintain LDO. In the case where VIN is falling faster than
LDO, the pass MOSFET is also on, and the LDO load
capacitor is discharged through the pass MOSFET to VIN.
Thus, provided VIN does not fall too fast, the core voltage
(LDO) does not exceed the I/O voltage (VIN) by more than
maximum of 0.4V.
2. VOUT rises faster than LDO. The switcher uses control
methods (5) and (6) described in the section Methods
of Control on page 23.
Power-down
This condition depends upon the regulator load current
and capacitance and the relative fall times of the VIN1 and
VIN2 supplies. There are two cases:
Shorted Load
1. VOUT falls faster than LDO. The LDO uses control
methods (1) and (2) described in the section Methods
of Control on page 23.
1. LDO shorted to ground. This will cause the I/O voltage
to exceed the core voltage by more than 2.1V. No load
protection.
In the case VIN1 = VIN2, the intrinsic operation turns
on both the buck high side MOSFET and the LDO
external Pass MOSFET, and discharges the LDO load
capacitor into the VIN supply.
2. VIN shorted to ground. Until the LDO load capacitance
is discharged, the core voltage exceeds the I/O voltage
by more than 0.4V. By the intrinsic operation of the
LDO, the load capacitor is discharged rapidly through
the Pass MOSFET to VIN.
2. LDO falls faster than VOUT. The switcher uses control
methods (5) and (6) described in the section Methods
of Control on page 23.
3. LDO shorted to supply. No load protection.
Single 5.0V Supply, VIN1 = VIN2, or Dual Supply VIN1
VIN2
Shorted Load
1. VOUT shorted to ground. The LDO uses method (1)
and (2) described in the section Methods of Control on
page 23.
The switcher VOUT supplies the microprocessor I/O
voltage. The LDO supplies the core (e.g., 1.5V nominal) (see
Figure 19, page 23).
2. LDO shorted to ground. The switcher uses control
methods (5) and (6) described in the section Methods
of Control on page 23.
Power-up
This condition depends upon the regulator current limit,
load current and capacitance, and the relative rise times of
the VIN1 and VIN2 supplies. There are two cases:
3. VIN1 shorted to ground. Device is not working.
4. VIN2 shorted to ground with VIN1 and VIN2 different.
This is equivalent to the switcher output shorted to
ground.
1. VOUT rises faster than LDO. The switcher VOUT uses
control methods (1) and (2) described in the section
Methods of Control on page 23.
5. VOUT shorted to supply. No load protection. 34701 is
protected by current limit and thermal shutdown.
2. LDO rises faster than VOUT. The LDO uses control
methods (5) and (6) described in the section Methods
of Control on page 23.
6. LDO shorted to supply. No load protection. 34701 is
protected by current limit and thermal shutdown.
INVERTED OPERATING MODE
Power-down
This condition depends upon the regulator load current
and capacitance and the relative fall times of the VIN1 and
VIN2 supplies. There are two cases:
Single 3.3V Supply, VIN = VIN1 = VIN2 = 3.3V
The 3.3V supplies the microprocessor I/O voltage, the
LDO supplies core voltage (e.g., 1.5V nominal), and the
switcher VOUT operates independently. Power sequencing
34701
Analog Integrated Circuit Device Data
Freescale Semiconductor
25
CTIONAL DEVICE OPERATION
OPERATIONAL MODES
1. LDO falls faster than VOUT . The VOUT uses control
methods (4) and (5) described in the section Methods
of Control on page 23.
Shorted Load
1. LDO shorted to ground. The VOUT uses methods (1)
and (2) described in the section Methods of Control on
page 23.
In the case VIN1 = VIN2, the intrinsic operation turns
on both the buck high side MOSFET and the LDO
external Pass MOSFET, and discharges the VOUT
load capacitor into the VIN supply.
2. VOUT shorted to ground. The LDO uses control
methods (5) and (6) described in the section Methods
of Control on page 23.
2. VOUT falls faster than LDO. The LDO uses control
methods (5) and (6) described in the section Methods
of Control on page 23.
3. VIN1 shorted to ground. Device is not working.
4. VIN2 shorted to ground. This is equivalent to the
switcher VOUT output shorted to ground.
5. LDO shorted to supply. No load protection. 34701 is
protected by current limit and thermal shutdown.
6. VOUT shorted to supply. No load protection. 34701 is
protected by current limit and thermal shutdown.
LOGIC COMMANDS AND REGISTERS
2
assure its unique address. Figure 21 illustrates the flexible
addressing feature for a 7-bit address. Table 6 provides the
definition of the selectable portion of the device address.
I C BUS OPERATION
The 34701 device is compatible with the I2C interface
standard. SDA and SCL pins are the Serial Data and Serial
Clock pins of the I2C bus.
When the ADDR pin is used and put to low level, pull the
ADDR pin to ground through a 10k resistor.
2
I C COMMAND AND DATA FORMATS
MSB
6
LSB
Bits
3
Communication Start
5
1
4
1
2
1
0
Communication starts with a START condition, followed by
the slave device unique address. The Read/Write (R/W) bit
defines whether the data should be read from or written to the
device (the 34701 operates only as a slave device; therefore,
the R/W bit should always be set to 0). The 34701 responds
by sending the Acknowledge bit (Ack) to the master device.
Figure 20 illustrates the beginning of an I2C communication
for a 7-bit slave address.
1
0
1 A1 A0
Fixed Address Selectable
Address
Figure 21. Address Bit Definition for 7-Bit Address
Table 6. Definition of Selectable Portion of Device
Address
CLKSEL Pin
Low
ADDR Pin
Low
A1
0
A0
0
Ack
S
7-Bit Address
R/W
Low
High (Open)
Low
0
1
Figure 20. Communication Start Using 7-Bit Address
Slave Address Definition
High (Open)
High (Open)
1
0
High (Open)
1
1
34701 has the two least significant address bits (LSB)
defined by the state of the CLKSEL pin (A1) and the ADDR
pin (A0).
Writing Data Into the Slave Device
After the address acknowledgment by the slave, DATA
can be written into the slave registers. The R/W bit must be
set to 0 to allow DATA to be written into the 34702. Figure 22
shows the data write sequence. Actions performed by the
slave device are grayed.
Note The state of the CLKSEL pin also defines the
configuration of the oscillator synchronization CLKSYN pin.
Leaving the CLKSEL pin open or pulling it high defines the
CLKSYN pin as an oscillator output. When the CLKSEL pin
is pulled low, the CLKSYN pin is configured as a
synchronization input for the external clock signal.
S
7-Bit Address
0
Ack
DATA
Ack
This feature allows up to four 34701 ICs to communicate
in the same I2C bus, all of them sharing the same high order
address bits. A different combination of the two LSB address
bits A1 and A0 can be assigned to each individual part to
(Write)
Figure 22. Data Transfer for Write Operations
34701
Analog Integrated Circuit Device Data
26
Freescale Semiconductor
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
DATA Definition
Table 8. Command Byte Definitions
The DATA field in the single Data Transfer contains one or
several Command Bytes. The Command Byte identifies the
kind of operation required by the master to be performed and
has two fields, as illustrated in Figure 23:
Watchdog
Programming
0
0
1
1
1
1
0
0
0
0
0
0
0
0
0
0
1st Command
WD OFF
(As a 2nd
Command Byte)
(24)
1. Address field
2. Value field
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
WD 1280ms
Wind. OFF
WD 320ms
Wind. OFF
The address field is selected from the list in Table 7.
WD 80ms
Wind. OFF
MSB
7
LSB
Bits
6
5
4
3
2
1
0
WD 20ms
Wind. OFF
D6 D5 D4 D3 D2 D1 D0
D7
WD 1280ms
Wind. ON
Address Field
Value Field
Figure 23. Command Byte
WD 320ms
Wind. ON
Table 7. Address Field Definitions
WD 80ms
Wind. ON
Address Field
Operation
Write
WD 20ms
Wind. ON
001
011
Voltage Margining
Watchdog
W
W
Notes
24. The Watchdog timer is turned ON automatically after
receiving any other valid command byte changing watchdog
time.
Refer to Table 8, page 27, which summarizes the value
field definitions for the entire set of operation options.
Table 8. Command Byte Definitions
Security in Writing Commands
To improve the security level, a so-called first command is
defined to initiate each write communications. The first
command identifies the operation, which is executed by the
following command byte.
Operation
Address
Value
Action
Voltage Margining
0
0
0
0
1
1
0
x
0
0
0
0
0
0
0
0
1st Command
(As a 2nd
Command Byte)
Output
Nominal
A first command has the address field equal to the related
operation one, followed by a null value field (all zeros).
Table 9 summarizes first command definitions. The master
sends the first command before the command byte for the
intended operation.
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
x
x
x
x
x
x
0
0
0
0
0
0
0
0
0
1
1
1
0
1
1
0
0
1
1
0
1
0
1
0
+ 1.0%
+ 2.0%
+ 3.0%
+ 4.0%
+ 5.0%
+ 6.0%
Table 9. First Command Definitions
LDO Output: x=0
First Command
001 00000
Operation
Switcher Output
x=1
Voltage Margining
011 00000
Watchdog Programming
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
x
x
x
x
x
x
x
x
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
+ 7.0%
- 1.0%
- 2.0%
- 3.0%
- 4.0%
- 5.0%
- 6.0%
- 7.0%
VOLTAGE MARGINING OPERATION
After starting the communication in Writing mode, the
master sends the first command followed by the specific
command byte to set the required voltage margining for either
the LDO or the switcher (see Figure 24). To achieve a
simultaneous set for both LDO and switcher, two specific
commands must be issued in sequence after the first
command, one for each supply.
34701
Analog Integrated Circuit Device Data
Freescale Semiconductor
27
CTIONAL DEVICE OPERATION
OPERATIONAL MODES
address acknowledge sent by 34702. I2C bus protocol
defines this circumstance as a master-transmitter and slave-
receiver configuration.
0
0
1
0 0
0
0
0
0 0 1 x x x x x
Ack
Figure 27 illustrates a communication beginning with the
slave address, the first command for voltage margining, and
a third byte containing the address field 001 and the value
field 00101 corresponding with the LDO fifth setting (LDO
output voltage = +5% above its nominal value). If a
simultaneous setting for switcher is needed, a fourth byte
should be included before the STOP condition (P); for
instance, 001 11100 to set the switcher in its twelfth setting
(switcher output voltage = -5% below its nominal value) - see
Figure 28.
First Byte for Voltage Margining
Command Byte
Figure 24. Voltage Margining Programming
(One Supply Only)
Note: x bits, which set the voltage margining value are
defined in Table 8.
WATCHDOG PROGRAMMING OPERATION
For watchdog operation control, the master periodically
sends a watchdog first command followed by a command
byte selecting, or confirming, the watchdog period according
to the options listed in Table 8. See Figure 25 for the
watchdog timer programming command example.
The example of data transfer setting the watchdog timer is
shown in the Figure 26.
The internal watchdog timer is turned ON by receiving a
valid watchdog programming command (after receiving the
watchdog programming first command), and it is cleared
each time the next watchdog programming command is
written into the device, provided it arrives during the window
open time. Thus, the watchdog programming command
clears the timer and sets the new timing conditions at the
same time. The watchdog programming first command
01100000 sent twice shuts the timer OFF, and the watchdog
function is disabled. Any other valid watchdog command
turns the timer ON again.
A2 A1
S
A6 A5 A4 A3
A0 0 Ack
Write
START
Slave Address
0
1
1
0
0
0
0 Ack
0
First Command for Watchdog Programming
0
1
1
0
1
0
0
1 Ack
P
STOP
Address Field Value Field:
Time-out WD = 320 ms
(Window OFF)
0
1
1
0 0
0
0
0
0 1 1 x x x x x
Ack
Figure 26. Data Transfer Example - Watch Dog Timer
Setting.
First Byte for Watchdog Programming Command Byte
Figure 25. Watchdog Timer Programming
A2 A1
S
A6 A5 A4 A3
A0 0 Ack
Write
Note: x bits, which set the watchdog timer value are
defined in Table 8, page 27.
START
Slave Address
Communication Stop
0
0
1
0
0
0
0 Ack
0
Only the master can terminate the data transfer by issuing
a STOP condition. The slave waits for this condition to
resume its initial state waiting for the next START condition
(see Figure 26).
First Command for Voltage Margining
0
0
1
0
0
1
0
1 Ack
P
STOP
Address Field Value Field = LDO
5th Setting
COMPLETE DATA TRANSFER EXAMPLES
The master device controlling the I2C bus always starts
addressing a 34701 slave IC in writing mode (R/W = 0) to
enable it to write a command byte just after receiving the
Figure 27. Data Transfer Example - LDO Voltage
Margining
34701
Analog Integrated Circuit Device Data
28
Freescale Semiconductor
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
A2 A1
S
A6 A5 A4 A3
A0 0 Ack
Write
START
Slave Address
0
0
1
0
0
0
0 Ack
0
First Command for Voltage Margining
0
0
1
0
0
1
0
1 Ack
Address Field Value Field: LDO
LDO = Nom. + 5%
V
0
0
1
1
1
1
0
0 Ack
P
STOP
Address Field Value Field: Switcher
OUT = Nom. - 5%
V
Figure 28. Data Transfer Example - LDO and Switcher
Voltage Margining
34701
Analog Integrated Circuit Device Data
Freescale Semiconductor
29
CAL APPLICATIONS
TYPICAL APPLICATIONS
load regulation. The control circuit block diagram is shown in
Figure 29.
BUCK REGULATOR CONTROL CIRCUIT
The 34701 buck regulator utilizes a PWM Voltage Mode
topology with feed-forward to achieve an excellent line and
L
Figure 29. Buck Regulator Control Circuit
The integrated 40pF capacitor CF charged through the
external resistor R4 provides the feed-forward ramp
waveform, the amplitude of which is proportional to the input
voltage, thus providing the feed-forward function.
1
------------------------------------------
=
fzc
2C2R1 + R3
The Feed-Forward implemented by resistor R4 and
integrated capacitor CF creates a pole in the overall loop
transfer function, the frequency of which can be calculated
from the following formula.
Figure 30 shows the Bode plot of the 34701 buck regulator
control loop gain and phase versus frequency.
The first double pole on the Bode plot is created by the
buck regulator output L-C filter, and its frequency can be
calculated as:
VIN
--------------------------------------------------------------- ----------------------
1
fpFF
=
VIN – VRef
2R4CF
1
1
------- -------------------------------
+ Vm1
----------------------
fLC
=
fsw
R4CF
2 COL
Where VRef is the buck regulator reference voltage
(VRef = 0.8V typ.) at the INV pin,
Where CO is the value of the buck output capacitor and L
is the inductance value of the output filter inductor L.
VIN is the buck regulator input voltage,
Vm1 is the ramp generated by the internal ramp
generator (Vm1 = 0.5V typ.).
The frequency of the compensating zero can be calculated
as follows.
34701
Analog Integrated Circuit Device Data
30
Freescale Semiconductor
TYPICAL APPLICATIONS
.
1
----------------------------------------------------------------------------------------
R2 = VRef
Gain
[dB]
VO + IO RL – VRef
VO – VRef
------------------------------------------------------- -------------------------
+
20
f
R4
R1
LC
f
z(c)
Where VRef is the buck regulator reference voltage
(VRef = 0.8V typ.) at the INV pin,
f
BW
0
VO is the selected output voltage,
f
f
z(ESR) p(FF)
IO is the output load current,
RL is the DC resistance of the inductor L.
f
p(c)
-20
It is apparent that the buck regulator output voltage is
affected by the voltage drop caused by the inductor serial
resistance and the regulator output current. In those
applications which do not require precise output voltage,
setting the formula for calculating selected output voltage can
be simplified as follows:
-40
-180
Phase
[Deg.]
1
----------------------------------------------------------------
R2 = VRef
R1 + R4
--------------------------
VO – VRef
R1 R4
-2 70
Linear Regulator Output Voltage
The output voltage of the linear regulator (LDO) can be set
by a simple resistor divider according to the following formula:
RU
-------
VLDO = VRef 1 +
RL
-3 60
1.0
10
100
1000
10000
Frequency [kHz]
Where VRef is the linear regulator reference voltage
(VRef = 0.8V typ.) at the LFB pin,
Figure 30. Buck Control Loop Bode Plot
The frequency of the zero created by the ESR of the output
VLDO is the LDO selected output voltage,
RU is the “upper” resistor of the LDO resistor divider,
RL is the “lower” resistor of the LDO resistor divider.
capacitor CO is calculated as:
Figure 31 describes the 34701 linear regulator circuit with
the resistor divider RU, RL setting the output voltage VLDO.
1
----------------------------
fzESR
=
2COESR
Where CO is the value of the buck regulator output
capacitor, and ESR is the equivalent series resistance of the
output capacitor.
2.8 V to 6.0 V Input
MC34701
VIN1
The frequency of the compensating network pole can be
calculated as follows:
LDRV
CS
1
------------------------------------------
2C2
fpc
=
V
R
LDO
S
R1R3
--------------------------
LDO
LFB
R1 + R3
R
U
C
LDO
The well designed and compensated buck regulator
should yield at least 45 deg. phase margin m of its overall
loop as depicted in the Figure 30, page 31.
R
L
LCMP
LDO
Compensation
Selecting Buck Regulator Output Voltage
The 34701 buck regulator output voltage can be set by
selecting the right value of the resistors R1, R2 and R4, and
can be determined from the following formula (see Figure 29,
page 30 for the component references):
Figure 31. 34701Linear Regulator Circuit
34701
Analog Integrated Circuit Device Data
Freescale Semiconductor
31
CAL APPLICATIONS
NOTE: Freescale does not assume liability, endorse, or warrant
components from external manufacturers referenced in figures
or tables. Although Freescale offers component
recommendations, it is the customer’s responsibility to validate
their application.
Linear Regulator Current Limit
As described in the Linear Regulator Functional
Description section, the current limit of the linear regulator
can be adjusted by means of an external current sense
resistor RS. The voltage drop caused by the regulator output
current flowing through the current sense resistor RS is
sensed between the LDO and the CS pins. When the sensed
voltage exceeds 50mV (typical), the current limit timer starts
to time out while the control circuit limits the output current. If
the over-current condition lasts for more than 10ms, the linear
regulator is shut off and turned on again after 100ms. This
type of operation provides equivalent protection to the analog
“current foldback” operation.
*When mounted to an FR4 using 0.5 sq.in. drain pad size
The maximum power dissipation is limited by the
maximum operating junction temperature TJmax. The
allowed power dissipation in the given application can be
calculated from the following expression:
T
Jmax – TA
-----------------------------------------------------------
PDQmax
R
thJC + RthCB + RthBA
It is important to keep in mind that the amount of capacitive
load which can be supplied by the by the linear regulator is
limited by the setting of the LDO current limit. During the
power-up period, the linear regulator operates in the current
limit, supplying the current into the load of the LDO, which
includes all the capacitors connected to the regulator output.
If the total amount load is so large that the regulator could not
reach its regulation voltage in 10ms during the power-up, it
turns off and tries to power up again after 100ms. This
situation may lead to the power-up oscillations.
Where PD(Q)max is the power MOSFET maximum
allowed dissipation,
TJmax is the power MOSFET maximum operating
junction temperature,
TA is the ambient temperature,
RthJC is the power MOSFET thermal resistance
junction-to-case,
RthCB is the thermal resistance case-to-board,
RthBA is the thermal resistance board-to-ambient of
the PC board.
Linear Regulator External MOSFET
PCB Layout Considerations
The linear regulator uses an external N-channel power
MOSFET to provide a pass element for the power path. The
selection of the proper type of the external power MOSFET is
critical for optimum performance and safe operation of the
linear regulator.
As with any power application, the proper PCB layout
plays a critical role in the overall power regulator
performance. While good careful printed circuit board layout
significantly improves regulation parameters and
electromagnetic compatibility (EMC) performance of the
switching regulator, poor layout practices can lead not only to
significant degradation of regulation and EMC parameters,
but even to total dysfunction of the whole regulator IC.
The power MOSFET’s threshold voltage, RDS(on), gate
charge, capacitances and transconductance are important
parameters for the stable operation of the linear regulator
while the package of the power MOSFET determines the
maximum power dissipation, and hence the maximum output
current for the required input-to-output voltage drop. The
power dissipation of the external MOSFET can be calculated
from the simple formula:
Extreme care should be taken when laying out the ground
of the regulator circuit. In order to avoid any inductive or
capacitive coupling of the switching regulator noise into the
sensitive analog control circuits, the noisy power ground and
the clean quiet signal ground should be well separated on the
printed circuit board, and connected only at one connection
point. The power routing should be made by heavy traces or
areas of copper. The power path and its return should be
placed, if possible, atop each other on the different layers or
opposite sides of the PC board. The switching regulator input
and output capacitors should be physically placed very close
to the power pins (VIN2, SW, PGND) of the 34701 switching
regulator; and their ground pins, together with the 34701
power ground pins (PGND), should be connected by a single
island of the power ground copper to create the “single-point”
grounding. Figure 32 illustrates the 34701 switching regulator
grounding concept. The bootstrap capacitor Cb should be
tightly connected to the integrated circuit as well.
PDQ = ILDO VIN – VLDO
Where PD(Q) is the power MOSFET power dissipation
VIN is the LDO input voltage,
VLDO is the LDO output voltage,
ILDO is the LDO output load current.
Table 10 shows the recommended power MOSFET types
for the 34701 linear regulator, their typical power dissipation,
and thermal resistance junction-to-case.
Table 10. Recommended Power MOSFETs
Part No.
Package
Typ. PD
RthJ-C
IRL2703S
D2PAK
DPAK
2.0W
3.3°C/W
MTD20N03HDL
1.75W*
1.67°C/W
34701
Analog Integrated Circuit Device Data
32
Freescale Semiconductor
TYPICAL APPLICATIONS
The same guidelines as those for the layout of the main
switching buck regulator should be applied to the layout of the
low power auxiliary boost regulator and to some extent, the
power path of the linear regulator.
Vin = 5.0 V
VBST
BOOT
Cb
VIN2
SW
To L oad
Vout = 1.5 V
INV
Vout Return
PGND
GND
Power
Ground
Signal
Ground
Figure 32. 34701 Buck Regulator Layout
34701
Analog Integrated Circuit Device Data
Freescale Semiconductor
33
CAL APPLICATIONS
VIN1
VIN
+3.3V
Supply
Voltage
VDDI
VDDI
Internal
Supply
CIN
10uF
1.0 uF
VDDI
VBST
VBD
8.0V
VBST
VBST
Power
Enable
7.75V
CBST
10uF
LDRV
-
QLDO
+
Vref
CS
10uH
LBST
VDDI
Vref
VDDI
RS
0.022 R
Linear
Regulator
Control
VLDO=3.3V
@1.0A
LDO
Q5
Boost
Control
Bandgap
Voltage
Reference
Vref
Vref
I-lim
4.7k
1.5k
LFB
+3.3V
CLDO
5 x 2.2 uF
VDDI
or
EN1
EN2
VLDO
LCMP
100pF
1.5k
Pow. Seq.
VLDO
Q4
Power
Power
Down
6.8nF
Sequencing
Voltage Margining
W-dog Timer
5.1k
VBST
UVLO
VBST
RST
RST
to MCU
Reset
Reset
Control
VOUT
BOOT
VBST
Q6
Current
Limit
SysCon
INV
POR
Timer
VIN2
(2)
RT
I2C
Control
+3.3V
Supply
Voltage
VDDI
LFB
Buck
HS
&
LS
Driver
CIN
Rt
100k
Ct
Q1
Q2
2 x 22 uF
I2C
Control
100nF
SysCon
SoftSt
DB
0.1uF
L1
CB
VOUT=1.8V
Thermal
Limit
Buck
Control
Logic
SW
(2)
4.7 uH
+
ADDR
SDA
CO
100 uF
Rpd
I2C
PGND
(2)
300k
10k
Interface
Error
Amp.
PWM
To Reset
Control
0.8V
+
Switcher
Comp.
SCL
Oscillator
300kHz
+
-
INV
39k
-
VOUT
Q3
Ramp
Gen.
Rb
27k
300
VOUT
470pF
Pow.
Seq.
FREQ
RF
(4)
GND
CLKSYN
CLKSEL
(Optional)
Figure 33. Simplified Block Diagram and Basic Application
34701
Analog Integrated Circuit Device Data
34
Freescale Semiconductor
TYPICAL APPLICATIONS
D
D
D
D
G N
G N
G N
G N
2 5
2 4
9
8
O B O T
1
Figure 34. 34701 Typical Application Circuit
34701
Analog Integrated Circuit Device Data
Freescale Semiconductor
35
KAGE DIMENSIONS
PACKAGE DIMENSIONS
Important: For the most current package revision, visit www.freescale.com and perform a “keyword” search for the “98A”
number.
EW SUFFIX
32-PIN
98AARH99137A
REVISION B
34701
Analog Integrated Circuit Device Data
36
Freescale Semiconductor
PACKAGE DIMENSIONS
EW SUFFIX
32-PIN
98AARH99137A
REVISION B
34701
Analog Integrated Circuit Device Data
Freescale Semiconductor
37
SION HISTORY
REVISION HISTORY
REVISION
5.0
DATE
2/2006
2/2007
DESCRIPTION OF CHANGES
• Changed Document Order No.
• Updated to the current Freescale form and style.
• Changed the status from Advance Information to Final.
• Added Peak Package Reflow Temperature During Reflow(2)
• Added Notes (2) and (3)
6.0
(3)
,
• Added MCZ34701EW/R2 to the ordering information
• Updated the 98ARH99137A package drawing to Rev. B
8/2007
7.0
34701
Analog Integrated Circuit Device Data
38
Freescale Semiconductor
RoHS-compliant and/or Pb-free versions of Freescale products have the functionality
and electrical characteristics of their non-RoHS-compliant and/or non-Pb-free
counterparts. For further information, see http://www.freescale.com or contact your
Freescale sales representative.
How to Reach Us:
Home Page:
www.freescale.com
Web Support:
http://www.freescale.com/support
For information on Freescale’s Environmental Products program, go to http://
www.freescale.com/epp.
USA/Europe or Locations Not Listed:
Freescale Semiconductor, Inc.
Technical Information Center, EL516
2100 East Elliot Road
Tempe, Arizona 85284
+1-800-521-6274 or +1-480-768-2130
www.freescale.com/support
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
www.freescale.com/support
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of any
product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters that may be
provided in Freescale Semiconductor data sheets and/or specifications can and do vary
in different applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer application by
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064
Japan
0120 191014 or +81 3 5437 9125
support.japan@freescale.com
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
+800 2666 8080
support.asia@freescale.com
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Semiconductor was negligent regarding the design or manufacture of the part.
Denver, Colorado 80217
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
All other product or service names are the property of their respective owners.
1-800-441-2447 or 303-675-2140
Fax: 303-675-2150
© Freescale Semiconductor, Inc., 2007. All rights reserved.
LDCForFreescaleSemiconductor@hibbertgroup.com
MC34701
Rev 7.0
8/2007
相关型号:
MCZ34701EW/R2
1.5A SWITCHING REGULATOR, 400kHz SWITCHING FREQ-MAX, PDSO32, 0.65 MM PITCH, LEAD FREE, SOIC-32
NXP
MCZ34702EW/R2
4 A SWITCHING REGULATOR, 400 kHz SWITCHING FREQ-MAX, PDSO32, 0.65 MM PITCH, LEAD FREE, SOIC-32
NXP
MCZ79076EGR2
SPECIALTY ANALOG CIRCUIT, PDSO16, 1.27 MM PITCH, LEAD FREE, PLASTIC, MS-013AA, SOIC-16
NXP
©2020 ICPDF网 联系我们和版权申明