NX3L2T66_09 [NXP]
Dual low-ohmic single-pole single-throw analog switch; 双低电阻单刀单掷模拟开关型号: | NX3L2T66_09 |
厂家: | NXP |
描述: | Dual low-ohmic single-pole single-throw analog switch |
文件: | 总20页 (文件大小:146K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
NX3L2T66
Dual low-ohmic single-pole single-throw analog switch
Rev. 03 — 28 August 2009
Product data sheet
1. General description
The NX3L2T66 provides two low-ohmic single pole single throw analog switch functions.
Each switch has two input/output terminals (nY and nZ) and an active HIGH enable input
(nE). When pin nE is LOW, the analog switch is turned off.
Schmitt-trigger action at the enable input (nE) makes the circuit tolerant to slower input
rise and fall times across the entire VCC range from 1.4 V to 4.3 V.
A low input voltage threshold allows pin nE to be driven by lower level logic signals without
a significant increase in supply current ICC. This makes it possible for the NX3L2T66 to
switch 4.3 V signals with a 1.8 V digital controller, eliminating the need for logic level
translation.
The NX3L2T66 allows signals with amplitude up to VCC to be transmitted from nY to nZ; or
from nZ to nY. Its low ON resistance (0.5 Ω) and flatness (0.13 Ω) ensures minimal
attenuation and distortion of transmitted signals.
2. Features
I Wide supply voltage range from 1.4 V to 4.3 V
I Very low ON resistance (peak):
N 1.6 Ω (typical) at VCC = 1.4 V
N 1.0 Ω (typical) at VCC = 1.65 V
N 0.55 Ω (typical) at VCC = 2.3 V
N 0.50 Ω (typical) at VCC = 2.7 V
N 0.50 Ω (typical) at VCC = 4.3 V
I High noise immunity
I ESD protection:
N HBM JESD22-A114E Class 3A exceeds 7500 V
N MM JESD22-A115-A exceeds 200 V
N CDM AEC-Q100-011 revision B exceeds 1000 V
I CMOS low-power consumption
I Latch-up performance exceeds 100 mA per JESD 78 Class II Level A
I 1.8 V control logic at VCC = 3.6 V
I Control input accepts voltages above supply voltage
I Very low supply current, even when input is below VCC
I High current handling capability (350 mA continuous current under 3.3 V supply)
I Specified from −40 °C to +85 °C and from −40 °C to +125 °C
NX3L2T66
NXP Semiconductors
Dual low-ohmic single-pole single-throw analog switch
3. Applications
I Cell phone
I PDA
I Portable media player
4. Ordering information
Table 1.
Ordering information
Type number
Package
Temperature range Name
Description
Version
NX3L2T66GT
NX3L2T66GD
NX3L2T66GM
−40 °C to +125 °C
−40 °C to +125 °C
−40 °C to +125 °C
XSON8 plastic extremely thin small outline package; no leads; SOT833-1
8 terminals; body 1 × 1.95 × 0.5 mm
XSON8U plastic extremely thin small outline package; no leads; SOT996-2
8 terminals; UTLP based; body 3 × 2 × 0.5 mm
XQFN8U plastic extremely thin quad flat package; no leads;
SOT902-1
8 terminals; UTLP based; body 1.6 × 1.6 × 0.5 mm
5. Marking
Table 2.
Marking codes[1]
Type number
NX3L2T66GT
NX3L2T66GD
NX3L2T66GM
Marking code
DOO
DOO
DOO
[1] The pin 1 indicator is located on the lower left corner of the device, below the marking code.
6. Functional diagram
1Y
1E
2Z
1Z
2Y
Y
E
Z
2E
001aag497
001aah372
Fig 1. Logic symbol
Fig 2. Logic diagram (one switch)
NX3L2T66_3
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 03 — 28 August 2009
2 of 20
NX3L2T66
NXP Semiconductors
Dual low-ohmic single-pole single-throw analog switch
7. Pinning information
7.1 Pinning
NX3L2T66
1Y
1Z
1
2
3
4
8
7
6
5
V
CC
NX3L2T66
1Y
1Z
1
2
3
4
8
7
6
5
V
CC
1E
2Z
2Y
1E
2Z
2Y
2E
2E
GND
GND
001aaj083
001aaj536
Transparent top view
Transparent top view
Fig 3. Pin configuration SOT833-1 (XSON8)
Fig 4. Pin configuration SOT996-2 (XSON8U)
NX3L2T66
terminal 1
index area
1E
1
7
6
5
1Y
1Z
2E
2Z
2Y
2
3
001aaj084
Transparent top view
Fig 5. Pin configuration SOT902-1 (XQFN8U)
7.2 Pin description
Table 3.
Symbol
Pin description
Pin
Description
SOT833-1 and SOT996-2
SOT902-1
1Y, 2Y
1Z, 2Z
GND
1, 5
2, 6
4
7, 3
6, 2
4
independent input or output
independent input or output
ground (0 V)
1E, 2E
VCC
7, 3
8
1, 5
8
enable input (active HIGH)
supply voltage
NX3L2T66_3
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 03 — 28 August 2009
3 of 20
NX3L2T66
NXP Semiconductors
Dual low-ohmic single-pole single-throw analog switch
8. Functional description
Table 4.
Function table[1]
Input nE
Switch
L
OFF-state
ON-state
H
[1] H = HIGH voltage level;
L = LOW voltage level.
9. Limiting values
Table 5.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol
VCC
VI
Parameter
Conditions
enable input nE
VI < −0.5 V
Min
−0.5
−0.5
−0.5
−50
-
Max
+4.6
+4.6
VCC + 0.5
-
Unit
V
supply voltage
input voltage
[1]
[2]
V
VSW
IIK
switch voltage
input clamping current
V
mA
mA
mA
ISK
switch clamping current VI < −0.5 V or VI > VCC + 0.5 V
±50
ISW
switch current
VSW > −0.5 V or VSW < VCC + 0.5 V;
-
±350
source or sink current
VSW > −0.5 V or VSW < VCC + 0.5 V;
pulsed at 1 ms duration, < 10% duty cycle;
peak current
-
±500
mA
Tstg
Ptot
storage temperature
total power dissipation
−65
+150
250
°C
[3]
Tamb = −40 °C to +125 °C
-
mW
[1] The minimum input voltage rating may be exceeded if the input current rating is observed.
[2] The minimum and maximum switch voltage ratings may be exceeded if the switch clamping current rating is observed but may not
exceed 4.6 V.
[3] For XSON8, XSON8U and XQFN8U packages: above 118 °C the value of Ptot derates linearly with 7.8 mW/K.
10. Recommended operating conditions
Table 6.
Recommended operating conditions
Symbol Parameter
Conditions
Min
1.4
0
Typ
Max
4.3
Unit
V
VCC
VI
supply voltage
-
-
-
-
-
input voltage
enable input nE
4.3
V
[1]
[2]
VSW
Tamb
∆t/∆V
switch voltage
0
VCC
+125
200
V
ambient temperature
input transition rise and fall rate
−40
-
°C
ns/V
VCC = 1.4 V to 4.3 V
[1] To avoid sinking GND current from terminal nZ when switch current flows in terminal nY, the voltage drop across the bidirectional switch
must not exceed 0.4 V. If the switch current flows into terminal nZ, no GND current will flow from terminal nY. In this case, there is no
limit for the voltage drop across the switch.
[2] Applies to control signal levels.
NX3L2T66_3
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 03 — 28 August 2009
4 of 20
NX3L2T66
NXP Semiconductors
Dual low-ohmic single-pole single-throw analog switch
11. Static characteristics
Table 7.
Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground 0 V).
Symbol Parameter
Conditions
25 °C
−40 °C to +125 °C
Unit
Min
Typ
Max
Min
Max
Max
(85 °C) (125 °C)
VIH
HIGH-level
input voltage
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VCC = 3.6 V to 4.3 V
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VCC = 3.6 V to 4.3 V
0.9
0.9
1.1
1.3
1.4
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.9
0.9
1.1
1.3
1.4
-
-
-
-
-
V
V
V
V
V
V
V
V
V
V
µA
-
-
-
-
-
-
-
-
-
VIL
LOW-level
input voltage
0.3
0.4
0.4
0.5
0.6
-
0.3
0.4
0.4
0.5
0.6
±0.5
0.3
0.3
0.4
0.5
0.6
±1
-
-
-
-
-
-
-
-
II
input leakage enable input nE;
-
-
current
VI = GND to 4.3 V;
CC = 1.4 V to 4.3 V
V
IS(OFF)
OFF-state
leakage
current
nY port; see Figure 6
VCC = 1.4 V to 3.6 V
VCC = 3.6 V to 4.3 V
nZ port; see Figure 7
VCC = 1.4 V to 3.6 V
VCC = 3.6 V to 4.3 V
-
-
-
-
±5
-
-
±50
±50
±500 nA
±500 nA
±10
IS(ON)
ON-state
leakage
current
-
-
-
-
±5
-
-
±50
±50
±500 nA
±500 nA
±10
ICC
supply current VI = VCC or GND;
VSW = GND or VCC
VCC = 3.6 V
-
-
-
-
100
150
-
-
690
800
6000 nA
7000 nA
VCC = 4.3 V
∆ICC
additional
VSW = GND or VCC
supply current
VI = 2.6 V; VCC = 4.3 V
VI = 2.6 V; VCC = 3.6 V
VI = 1.8 V; VCC = 4.3 V
VI = 1.8 V; VCC = 3.6 V
VI = 1.8 V; VCC = 2.5 V
-
-
-
-
-
-
2.0
0.35
7.0
2.5
50
4.0
0.7
10.0
4.0
200
-
-
-
-
-
-
-
7
1
7
1
µA
µA
µA
µA
nA
pF
15
5
15
5
300
-
500
-
CI
input
1.0
capacitance
CS(OFF) OFF-state
capacitance
-
-
35
-
-
-
-
-
-
-
-
pF
pF
CS(ON)
ON-state
110
capacitance
NX3L2T66_3
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 03 — 28 August 2009
5 of 20
NX3L2T66
NXP Semiconductors
Dual low-ohmic single-pole single-throw analog switch
11.1 Test circuits
V
V
CC
CC
nE
nZ
nE
nZ
V
V
IH
IL
nY
nY
I
I
S
S
GND
GND
V
V
V
V
O
I
O
I
001aaj221
001aaj222
VI = 0.3 V or VCC − 0.3 V; VO = VCC − 0.3 V or 0.3 V.
VI = 0.3 V or VCC − 0.3 V; VO = open circuit.
Fig 6. Test circuit for measuring OFF-state leakage
current
Fig 7. Test circuit for measuring ON-state leakage
current
11.2 ON resistance
Table 8.
ON resistance
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for graphs see Figure 9 to Figure 15.
Symbol Parameter
Conditions
−40 °C to +85 °C
−40 °C to +125 °C Unit
Min Typ[1] Max
Min
Max
RON(peak) ON resistance (peak)
VI = GND to VCC;
I
SW = 100 mA;
see Figure 8
VCC = 1.4 V
VCC = 1.65 V
VCC = 2.3 V
VCC = 2.7 V
VCC = 4.3 V
-
-
-
-
-
1.6
1.0
3.7
1.6
-
-
-
-
-
4.1
1.7
0.9
0.9
0.9
Ω
Ω
Ω
Ω
Ω
0.55
0.5
0.8
0.75
0.75
0.5
[2]
∆RON
ON resistance mismatch VI = GND to VCC;
between channels
I
SW = 100 mA
VCC = 1.4 V
VCC = 1.65 V
VCC = 2.3 V
VCC = 2.7 V
VCC = 4.3 V
-
-
-
-
-
0.04
0.04
0.02
0.02
0.02
0.3
0.2
-
-
-
-
-
0.3
0.3
0.1
0.1
0.1
Ω
Ω
Ω
Ω
Ω
0.08
0.075
0.075
NX3L2T66_3
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 03 — 28 August 2009
6 of 20
NX3L2T66
NXP Semiconductors
Dual low-ohmic single-pole single-throw analog switch
Table 8.
ON resistance …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for graphs see Figure 9 to Figure 15.
Symbol Parameter
Conditions
−40 °C to +85 °C
−40 °C to +125 °C Unit
Min Typ[1] Max
Min
Max
[3]
RON(flat)
ON resistance (flatness) VI = GND to VCC;
I
SW = 100 mA
VCC = 1.4 V
VCC = 1.65 V
VCC = 2.3 V
VCC = 2.7 V
VCC = 4.3 V
-
-
-
-
-
1.0
0.5
3.3
1.2
0.3
0.3
0.4
-
-
-
-
-
3.6
1.3
Ω
Ω
Ω
Ω
Ω
0.15
0.13
0.2
0.35
0.35
0.45
[1] Typical values are measured at Tamb = 25 °C.
[2] Measured at identical VCC, temperature and input voltage.
[3] Flatness is defined as the difference between the maximum and minimum value of ON resistance measured at identical VCC and
temperature.
11.3 ON resistance test circuit and graphs
001aag564
1.6
R
ON
(Ω)
1.2
V
SW
(1)
0.8
0.4
0
V
CC
(2)
nE
nZ
V
IH
(3)
(4)
(5)
nY
(6)
GND
V
I
I
SW
0
1
2
3
4
5
V (V)
I
001aaj223
RON = VSW / ISW
.
(1) VCC = 1.5 V.
(2) VCC = 1.8 V.
(3) VCC = 2.5 V.
(4) VCC = 2.7 V.
(5) VCC = 3.3 V.
(6) VCC = 4.3 V.
Measured at Tamb = 25 °C.
Fig 8. Test circuit for measuring ON resistance
Fig 9. Typical ON resistance as a function of input
voltage
NX3L2T66_3
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 03 — 28 August 2009
7 of 20
NX3L2T66
NXP Semiconductors
Dual low-ohmic single-pole single-throw analog switch
001aag565
001aag566
1.6
1.0
R
(Ω)
ON
R
(Ω)
ON
0.8
1.2
(1)
(2)
(3)
(4)
0.6
0.4
0.2
0
(1)
(2)
(3)
(4)
0.8
0.4
0
0
1
2
3
0
1
2
3
V (V)
I
V (V)
I
(1) Tamb = 125 °C.
(2) Tamb = 85 °C.
(3) Tamb = 25 °C.
(4) Tamb = −40 °C.
(1) Tamb = 125 °C.
(2) Tamb = 85 °C.
(3) Tamb = 25 °C.
(4) Tamb = −40 °C.
Fig 10. ON resistance as a function of input voltage;
Fig 11. ON resistance as a function of input voltage;
VCC = 1.8 V
VCC = 1.5 V
001aag567
001aag568
1.0
1.0
R
ON
R
ON
(Ω)
(Ω)
0.8
0.8
0.6
0.4
0.2
0
0.6
0.4
0.2
0
(1)
(2)
(3)
(4)
(1)
(2)
(3)
(4)
0
1
2
3
0
1
2
3
V (V)
V (V)
I
I
(1) Tamb = 125 °C.
(2) Tamb = 85 °C.
(3) Tamb = 25 °C.
(4) Tamb = −40 °C.
(1) Tamb = 125 °C.
(2) Tamb = 85 °C.
(3) Tamb = 25 °C.
(4) Tamb = −40 °C.
Fig 12. ON resistance as a function of input voltage;
CC = 2.5 V
Fig 13. ON resistance as a function of input voltage;
VCC = 2.7 V
V
NX3L2T66_3
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 03 — 28 August 2009
8 of 20
NX3L2T66
NXP Semiconductors
Dual low-ohmic single-pole single-throw analog switch
001aag569
001aaj896
1.0
1.0
R
ON
R
ON
(Ω)
(Ω)
0.8
0.8
(1)
(2)
(3)
(4)
0.6
0.4
0.2
0
0.6
0.4
0.2
0
(1)
(2)
(3)
(4)
0
1
2
3
4
0
1
2
3
4
5
V (V)
I
V (V)
I
(1) Tamb = 125 °C.
(2) Tamb = 85 °C.
(3) Tamb = 25 °C.
(4) Tamb = −40 °C.
(1) Tamb = 125 °C.
(2) Tamb = 85 °C.
(3) Tamb = 25 °C.
(4) Tamb = −40 °C.
Fig 14. ON resistance as a function of input voltage;
CC = 3.3 V
Fig 15. ON resistance as a function of input voltage;
VCC = 4.3 V
V
12. Dynamic characteristics
Table 9.
Dynamic characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for load circuit see Figure 17.
Symbol Parameter
Conditions
25 °C
−40 °C to +125 °C
Unit
Min Typ[1] Max
Min
Max
Max
(85 °C) (125 °C)
ten
enable time
nE to nZ or nY;
see Figure 16
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VCC = 3.6 V to 4.3 V
-
-
-
-
-
35
28
20
18
18
49
40
30
28
28
-
-
-
-
-
53
43
32
30
30
57
48
35
32
32
ns
ns
ns
ns
ns
tdis
disable time
nE to nZ or nY;
see Figure 16
VCC = 1.4 V to 1.6 V
VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VCC = 3.6 V to 4.3 V
-
-
-
-
-
32
23
14
11
11
70
55
25
20
20
-
-
-
-
-
80
60
30
25
25
90
65
35
30
30
ns
ns
ns
ns
ns
[1] Typical values are measured at Tamb = 25 °C and VCC = 1.5 V, 1.8 V, 2.5 V, 3.3 V and 4.3 V respectively.
NX3L2T66_3
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 03 — 28 August 2009
9 of 20
NX3L2T66
NXP Semiconductors
Dual low-ohmic single-pole single-throw analog switch
12.1 Waveform and test circuits
V
I
nE input
V
M
GND
t
t
en
dis
V
OH
V
V
X
X
nY output
OFF to HIGH
HIGH to OFF
GND
switch
switch
switch
disabled
enabled
disabled
001aah376
Measurement points are given in Table 10.
Logic level: VOH is the typical output voltage level that occurs with the output load.
Fig 16. Enable and disable times
Table 10. Measurement points
Supply voltage
VCC
Input
VM
Output
VX
1.4 V to 4.3 V
0.5VCC
0.9VOH
V
CC
nE
nY/nZ
nZ/nY
G
C
L
V
V
V
R
L
V
= 1.5 V
I
O
EXT
001aaj224
Test data is given in Table 11.
Definitions test circuit:
RL = Load resistance.
CL = Load capacitance including jig and probe capacitance.
VEXT = External voltage for measuring switching times.
Fig 17. Load circuit for measuring switching times
Table 11. Test data
Supply voltage
VCC
Input
VI
Load
CL
tr, tf
RL
1.4 V to 4.3 V
VCC
≤ 2.5 ns
35 pF
50 Ω
NX3L2T66_3
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 03 — 28 August 2009
10 of 20
NX3L2T66
NXP Semiconductors
Dual low-ohmic single-pole single-throw analog switch
12.2 Additional dynamic characteristics
Table 12. Additional dynamic characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); VI = GND or VCC (unless otherwise
specified); tr = tf ≤ 2.5 ns.
Symbol Parameter
Conditions
25 °C
Unit
Min
Typ
Max
[1]
THD
total harmonic
distortion
fi = 20 Hz to 20 kHz; RL = 32 Ω; see Figure 18
VCC = 1.4 V; VI = 1 V (p-p)
VCC = 1.65 V; VI = 1.2 V (p-p)
VCC = 2.3 V; VI = 1.5 V (p-p)
VCC = 2.7 V; VI = 2 V (p-p)
VCC = 4.3 V; VI = 2 V (p-p)
RL = 50 Ω; see Figure 19
-
-
-
-
-
0.15
0.10
0.02
0.02
0.02
-
-
-
-
-
%
%
%
%
%
[1]
[1]
f(−3dB)
−3 dB frequency
response
VCC = 1.4 V to 4.3 V
-
-
60
-
-
MHz
dB
αiso
isolation (OFF-state)
fi = 100 kHz; RL = 50 Ω; see Figure 20
VCC = 1.4 V to 4.3 V
−90
Vct
crosstalk voltage
between digital inputs and switch;
fi = 1 MHz; CL = 50 pF; RL = 50 Ω; see Figure 21
VCC = 1.4 V to 3.6 V
VCC = 3.6 V to 4.3 V
-
-
0.2
0.2
-
-
V
V
[1]
Xtalk
Qinj
crosstalk
between switches;
fi = 100 kHz; RL = 50 Ω; see Figure 22
VCC = 1.4 V to 4.3 V
-
−90
-
dB
charge injection
fi = 1 MHz; CL = 0.1 nF; RL = 1 MΩ; Vgen = 0 V;
R
gen = 0 Ω; see Figure 23
VCC = 1.5 V
-
-
-
-
-
3
3
3
3
6
-
-
-
-
-
pC
pC
pC
pC
pC
VCC = 1.8 V
VCC = 2.5 V
VCC = 3.3 V
VCC = 4.3 V
[1] fi is biased at 0.5VCC
.
12.3 Test circuits
V
0.5V
CC
CC
nE
V
R
L
IH
nY/nZ
nZ/nY
f
D
i
001aaj225
Fig 18. Test circuit for measuring total harmonic distortion
NX3L2T66_3
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 03 — 28 August 2009
11 of 20
NX3L2T66
NXP Semiconductors
Dual low-ohmic single-pole single-throw analog switch
V
0.5V
CC
CC
nE
V
R
L
IH
nY/nZ
nZ/nY
f
dB
i
001aaj226
Adjust fi voltage to obtain 0 dBm level at output. Increase fi frequency until dB meter reads −3 dB.
Fig 19. Test circuit for measuring the frequency response when channel is in ON-state
0.5V
V
0.5V
CC
R
CC
CC
R
nE
nY/nZ
V
IL
L
L
nZ/nY
f
dB
i
001aaj227
Adjust fi voltage to obtain 0 dBm level at input.
Fig 20. Test circuit for measuring isolation (OFF-state)
NX3L2T66_3
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 03 — 28 August 2009
12 of 20
NX3L2T66
NXP Semiconductors
Dual low-ohmic single-pole single-throw analog switch
V
CC
nE
nY/nZ
nZ/nY
G
V
R
L
R
L
C
L
V
V
O
I
0.5V
0.5V
CC
CC
off
001aaj228
a. Test circuit
logic
input (nE)
on
off
V
O
V
ct
001aaj231
b. input and output pulse definitions
Fig 21. Test circuit for measuring crosstalk voltage between digital inputs and switch
0.5V
CC
1E
V
R
L
IH
1Y or 1Z
1Z or 1Y
CHANNEL
ON
C
50 pF
f
50 Ω
L
i
V
V
O1
0.5V
CC
2E
V
R
L
IL
2Z or 2Y
2Y or 2Z
CHANNEL
OFF
R
50 Ω
i
C
50 pF
L
V
V
O2
001aah382
20 log10 (VO2 / VO1) or 20 log10 (VO1 / VO2).
Fig 22. Test circuit for measuring crosstalk between switches
NX3L2T66_3
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 03 — 28 August 2009
13 of 20
NX3L2T66
NXP Semiconductors
Dual low-ohmic single-pole single-throw analog switch
V
CC
nE
R
gen
nY/nZ
nZ/nY
G
C
L
V
V
V
R
L
V
gen
I
O
GND
001aaj229
a. Test circuit
logic
input (nE)
off
on
off
V
O
V
O
001aaj232
b. Input and output pulse definitions
Definition: Qinj = ∆VO × CL.
∆VO = output voltage variation.
Rgen = generator resistance.
Vgen = generator voltage.
Fig 23. Test circuit for measuring charge injection
NX3L2T66_3
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 03 — 28 August 2009
14 of 20
NX3L2T66
NXP Semiconductors
Dual low-ohmic single-pole single-throw analog switch
13. Package outline
XSON8: plastic extremely thin small outline package; no leads; 8 terminals; body 1 x 1.95 x 0.5 mm
SOT833-1
b
1
2
3
4
4×
(2)
L
L
1
e
8
7
6
5
e
1
e
1
e
1
8×
(2)
A
A
1
D
E
terminal 1
index area
0
1
2 mm
scale
DIMENSIONS (mm are the original dimensions)
(1)
A
A
1
UNIT
b
D
E
e
e
1
L
L
1
max max
0.25
0.17
2.0
1.9
1.05
0.95
0.35 0.40
0.27 0.32
mm
0.5 0.04
0.6
0.5
Notes
1. Including plating thickness.
2. Can be visible in some manufacturing processes.
REFERENCES
OUTLINE
VERSION
EUROPEAN
PROJECTION
ISSUE DATE
IEC
JEDEC
JEITA
- - -
07-11-14
07-12-07
SOT833-1
- - -
MO-252
Fig 24. Package outline SOT833-1 (XSON8)
NX3L2T66_3
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 03 — 28 August 2009
15 of 20
NX3L2T66
NXP Semiconductors
Dual low-ohmic single-pole single-throw analog switch
XSON8U: plastic extremely thin small outline package; no leads;
8 terminals; UTLP based; body 3 x 2 x 0.5 mm
SOT996-2
D
B
A
E
A
A
1
detail X
terminal 1
index area
e
1
C
M
M
v
C A
C
B
b
e
L
1
y
y
w
C
1
1
4
L
2
L
8
5
X
0
1
2 mm
scale
DIMENSIONS (mm are the original dimensions)
A
UNIT
A
1
b
D
E
e
e
1
L
L
L
v
w
y
y
1
1
2
max
0.05 0.35
0.00 0.15
2.1
1.9
3.1
2.9
0.5
0.3
0.15
0.05
0.6
0.4
mm
0.5
0.5
1.5
0.1
0.05 0.05
0.1
REFERENCES
OUTLINE
VERSION
EUROPEAN
PROJECTION
ISSUE DATE
IEC
- - -
JEDEC
JEITA
07-12-18
07-12-21
SOT996-2
- - -
Fig 25. Package outline SOT996-2 (XSON8U)
NX3L2T66_3
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 03 — 28 August 2009
16 of 20
NX3L2T66
NXP Semiconductors
Dual low-ohmic single-pole single-throw analog switch
XQFN8U: plastic extremely thin quad flat package; no leads;
8 terminals; UTLP based; body 1.6 x 1.6 x 0.5 mm
SOT902-1
D
B
A
terminal 1
index area
E
A
A
1
detail X
e
L
1
e
C
y
C
1
y
L
M
M
v
C A
C
B
4
w
5
6
7
3
2
metal area
not for soldering
e
1
b
e
1
1
terminal 1
index area
8
X
0
1
2 mm
scale
DIMENSIONS (mm are the original dimensions)
A
UNIT
A
1
b
D
E
e
e
1
L
L
v
w
y
y
1
1
max
0.05 0.25 1.65 1.65
0.00 0.15 1.55 1.55
0.35 0.15
0.25 0.05
mm
0.5
0.55
0.5
0.1
0.05 0.05 0.05
REFERENCES
OUTLINE
VERSION
EUROPEAN
PROJECTION
ISSUE DATE
IEC
JEDEC
MO-255
JEITA
05-11-25
07-11-14
SOT902-1
- - -
- - -
Fig 26. Package outline SOT902-1 (XQFN8U)
NX3L2T66_3
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 03 — 28 August 2009
17 of 20
NX3L2T66
NXP Semiconductors
Dual low-ohmic single-pole single-throw analog switch
14. Abbreviations
Table 13. Abbreviations
Acronym
CDM
Description
Charged Device Model
CMOS
ESD
Complementary Metal Oxide Semiconductor
ElectroStatic Discharge
Human Body Model
HBM
MM
Machine Model
15. Revision history
Table 14. Revision history
Document ID
NX3L2T66_3
Modifications:
Release date
20090828
Data sheet status
Change notice
Supersedes
Product data sheet
-
NX3L2T66_2
• Figure 6 “Test circuit for measuring OFF-state leakage current” updated.
• Table 8 “ON resistance”: RON(flat) values for VCC = 4.3 V updated.
NX3L2T66_2
NX3L2T66_1
20090420
Product data sheet
-
NX3L2T66_1
20081204
Product data sheet
-
-
NX3L2T66_3
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 03 — 28 August 2009
18 of 20
NX3L2T66
NXP Semiconductors
Dual low-ohmic single-pole single-throw analog switch
16. Legal information
16.1 Data sheet status
Document status[1][2]
Product status[3]
Development
Definition
Objective [short] data sheet
This document contains data from the objective specification for product development.
This document contains data from the preliminary specification.
This document contains the product specification.
Preliminary [short] data sheet Qualification
Product [short] data sheet Production
[1]
[2]
[3]
Please consult the most recently issued document before initiating or completing a design.
The term ‘short data sheet’ is explained in section “Definitions”.
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
16.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) may cause permanent
damage to the device. Limiting values are stress ratings only and operation of
the device at these or any other conditions above those given in the
Characteristics sections of this document is not implied. Exposure to limiting
values for extended periods may affect device reliability.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Terms and conditions of sale — NXP Semiconductors products are sold
subject to the general terms and conditions of commercial sale, as published
at http://www.nxp.com/profile/terms, including those pertaining to warranty,
intellectual property rights infringement and limitation of liability, unless
explicitly otherwise agreed to in writing by NXP Semiconductors. In case of
any inconsistency or conflict between information in this document and such
terms and conditions, the latter will prevail.
16.3 Disclaimers
General — Information in this document is believed to be accurate and
reliable. However, NXP Semiconductors does not give any representations or
warranties, expressed or implied, as to the accuracy or completeness of such
information and shall have no liability for the consequences of use of such
information.
No offer to sell or license — Nothing in this document may be interpreted
or construed as an offer to sell products that is open for acceptance or the
grant, conveyance or implication of any license under any copyrights, patents
or other industrial or intellectual property rights.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from national authorities.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in medical, military, aircraft,
space or life support equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
16.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
17. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
NX3L2T66_3
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 03 — 28 August 2009
19 of 20
NX3L2T66
NXP Semiconductors
Dual low-ohmic single-pole single-throw analog switch
18. Contents
1
2
3
4
5
6
General description . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Ordering information. . . . . . . . . . . . . . . . . . . . . 2
Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2
7
7.1
7.2
Pinning information. . . . . . . . . . . . . . . . . . . . . . 3
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3
8
Functional description . . . . . . . . . . . . . . . . . . . 4
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4
Recommended operating conditions. . . . . . . . 4
9
10
11
Static characteristics. . . . . . . . . . . . . . . . . . . . . 5
Test circuits. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ON resistance. . . . . . . . . . . . . . . . . . . . . . . . . . 6
ON resistance test circuit and graphs. . . . . . . . 7
11.1
11.2
11.3
12
Dynamic characteristics . . . . . . . . . . . . . . . . . . 9
Waveform and test circuits . . . . . . . . . . . . . . . 10
Additional dynamic characteristics . . . . . . . . . 11
Test circuits. . . . . . . . . . . . . . . . . . . . . . . . . . . 11
12.1
12.2
12.3
13
14
15
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 15
Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . 18
Revision history. . . . . . . . . . . . . . . . . . . . . . . . 18
16
Legal information. . . . . . . . . . . . . . . . . . . . . . . 19
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 19
Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 19
16.1
16.2
16.3
16.4
17
18
Contact information. . . . . . . . . . . . . . . . . . . . . 19
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2009.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
Date of release: 28 August 2009
Document identifier: NX3L2T66_3
相关型号:
©2020 ICPDF网 联系我们和版权申明