TJA1052IT/5 [NXP]
DATACOM, INTERFACE CIRCUIT, PDSO16, 7.50 MM, PLASTIC, SOT162-1, MS-013, SOP-16;
| 型号： | TJA1052IT/5 |
| 厂家： | 
NXP |
| 描述： | DATACOM, INTERFACE CIRCUIT, PDSO16, 7.50 MM, PLASTIC, SOT162-1, MS-013, SOP-16 电信 光电二极管 电信集成电路 |
| 文件： | 总20页 (文件大小：454K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TJA1052i
CAN
Galvanically isolated high-speed CAN transceiver
Rev. 2 — 12 July 2013
Product data sheet
1. General description
The TJA1052i is a high-speed CAN transceiver that provides a galvanically isolated
interface between a Controller Area Network (CAN) protocol controller and the physical
two-wire CAN bus. The TJA1052i is specifically targeted at Electric Vehicles (EV) and
Hybrid Electric Vehicles (HEV), where galvanic isolation barriers are needed between the
high- and low-voltage parts.
Safety: Isolation is required for safety reasons, eg. to protect humans from electric shock
or to prevent the electronics being damaged by high voltages.
Signal integrity: The isolator uses proprietary capacitive isolation technology to transmit
and receive CAN signals. This technology enables more reliable data communications in
noisy environments, such as high-voltage battery management systems or the drive and
regeneration systems in EVs and HEVs.
Performance: The transceiver is designed for high-speed (up to 1 Mbit/s) CAN
applications in the automotive industry, supplying the differential transmit and receive
capability to a CAN protocol controller in a microcontroller. Integrating the galvanic
isolation along with the transceiver in the TJA1052i removes the need for stand-alone
isolation. It also improves reliability and system performance parameters such as loop
delay.
The TJA1052i belongs to the third generation of high-speed CAN transceivers from NXP
Semiconductors, offering significant improvements over first- and second-generation
devices. It offers improved ElectroMagnetic Compatibility (EMC) and ElectroStatic
Discharge (ESD) performance, and also features ideal passive behavior to the CAN bus
when the transceiver supply voltage is off.
The TJA1052i is an excellent choice for all types of automotive and industrial CAN
networks where isolation is required for safety reasons or to enhance signal integrity in
noisy environments.
2. Features and benefits
2.1 General
Isolator and Transceiver integrated into a single SO16 package, reducing board space
Flawless cooperation between the Isolator and the Transceiver
Fewer components improves reliability in applications
Guaranteed performance (eg. max loop delay <220 ns)
Electrical transient immunity of 45 kV/s (typ)
ISO 11898-2 compliant
TJA1052i
NXP Semiconductors
Galvanically isolated high-speed CAN transceiver
Suitable for use in 12 V and 24 V systems; compatible with 3 V to 5 V microcontrollers
Bus common mode voltage (Vcm) = 25 V
Low ElectroMagnetic Emission (EME) and high ElectroMagnetic Immunity (EMI)
2.2 Power management
Functional behavior predictable under all supply conditions
Transceiver disengages from the bus when not powered up (zero load)
2.3 Protection
Up to 5 kV (RMS) rated isolation
Three versions available (1 kV, 2.5 kV and 5 kV)
Voltage compliant with UL 1577 (pending), IEC 61010 and IEC 60950
5 kV (RMS) rated isolation voltage compliant with UL 1577, IEC 61010 and IEC 60950
Supports ISO6469 ‘Electrically propelled road vehicles. Safety specifications.’
High ESD handling capability on the bus pins
Bus pins protected against transients in automotive environments
Transmit Data (TXD) dominant time-out function
Undervoltage detection on supply pins
3. Quick reference data
Table 1.
Symbol
IDD1
Quick reference data
Parameter
Conditions
Min
Typ Max Unit
supply current 1
VTXD = 0 V; bus dominant
VTXD = VDD1; bus recessive
VTXD = 0 V; bus dominant; 60 load
VTXD = VDD1; bus recessive
-
-
-
-
-
-
2.6
5.6
70
mA
mA
mA
mA
V
-
IDD2
supply current 2
-
-
10
Vuvd(swoff)(VDD2) switch-off undervoltage
detection voltage on pin VDD2
1.3
2.7
VESD
VCANH
VCANL
Tvj
electrostatic discharge voltage
voltage on pin CANH
IEC 61000-4-2 at pins CANH and CANL
no time limit; DC limiting value
8
-
-
-
-
-
+8
kV
V
58
58
40
40
+58
+58
voltage on pin CANL
no time limit; DC limiting value
V
virtual junction temperature
ambient temperature
+150 C
+125 C
Tamb
4. Ordering information
Table 2.
Ordering information
Type number
Package
Name
Description
Version
TJA1052IT/5
TJA1052IT/2
TJA1052IT/1
SO16
plastic small outline package; 16 leads; body width 7.5 mm
SOT162-1
TJA1052I
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 2 — 12 July 2013
2 of 20
TJA1052i
NXP Semiconductors
Galvanically isolated high-speed CAN transceiver
Table 3.
Voltage ratings
Type number
Rated insulation voltage according to
UL 1577, IEC 61010 and IEC 60950
TJA1052iT/5
TJA1052iT/2
TJA1052iT/1
5 kV (RMS)
2.5 kV (RMS)
1 kV (RMS)
5. Block diagram
V
DD1
V
DD2
1
11, 16
V
DD2
TEMPERATURE
PROTECTION
TJA1052I
13
CANH
CANL
SLOPE
CONTROL
AND
3
TIME-OUT
TXD
12
DRIVER
MODE
CONTROL
MUX
AND
DRIVER
5
RXD
WAKE-UP
FILTER
2, 7, 8
14
9, 10, 15
015aaa331
GND1
STB
GND2
Fig 1. Block diagram
TJA1052I
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 2 — 12 July 2013
3 of 20
TJA1052i
NXP Semiconductors
Galvanically isolated high-speed CAN transceiver
6. Pinning information
6.1 Pinning
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
V
V
DD2
DD1
GND1
TXD
GND2
STB
n.c.
CANH
CANL
TJA1052I
RXD
n.c.
V
DD2
GND1
GND1
GND2
GND2
015aaa330
Fig 2. Pin configuration diagram
6.2 Pin description
Table 4.
Pin description
Pin Description
Symbol
VDD1
1
2
3
4
5
6
7
8
9
supply voltage 1
ground supply 1[1]
transmit data input
not connected
GND1
TXD
n/c
RXD
receive data output; reads out data from the bus lines
n/c
not connected
ground supply 1[1]
ground supply 1[1]
ground supply 2[1]
GND1
GND1
GND2
GND2
VDD2
10 ground supply 2[1]
11 supply voltage 2
CANL
CANH
STB
12 LOW-level CAN bus line
13 HIGH-level CAN bus line
14 Standby mode control input[2]
15 ground supply 2[1]
GND2
VDD2
16 supply voltage 2
[1] All GND1 pins (pins 2, 7 and 8) should be connected together and to ground domain 1. All GND2 pins (pins
9, 10 and 15) should be connected together and to ground domain 2. Refer to the application notes for
further information.
[2] Setting STB HIGH disables the CAN bus connection.
TJA1052I
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 2 — 12 July 2013
4 of 20
TJA1052i
NXP Semiconductors
Galvanically isolated high-speed CAN transceiver
7. Functional description
7.1 Operation
7.1.1 Normal mode
During normal operation, the TJA1052i transceiver transmits and receives data via bus
lines CANH and CANL (see Figure 1 for the block diagram). The differential receiver
converts the analog data on the bus lines into digital data, which is output on pin RXD.
The slope of the output signals on the bus lines is controlled and optimized in a way that
guarantees the lowest possible EME.
The isolator used in the TJA1052i is an AC device that employs on-off keying to
guarantee the DC output state at all times. The states of TXD, RXD and the CAN bus at
start-up, shut-down and during normal operation are described in Table 5.
Care should be taken regarding power sequencing if the device is used in networks that
support remote wake-up (see Section 12 “Application information”).
Table 5.
Input/output states at start-up, shut-down and during normal operation
TXD
H
RXD VDD1
VDD2
CAN
Comments
H
L
>Vuvd(VDD1)
>Vuvd(stb)VDD2)
>Vuvd(stb)VDD2)
>Vuvd(stb)VDD2)
recessive
dominant
dominant
Normal mode operation
L
>Vuvd(VDD1)
unpowered
Normal mode with TXD dominant time-out active
X
X
dominant after VDD1 power loss until TXD dominant
timeout; recessive while VDD2 is ramping up from
an unpowered state
X
L
>Vuvd(VDD1)
unpowered
disconnected
RXD transitions L-to-H when VDD2 restored
7.1.2 Standby mode
Standby mode is provided to improve the response of the TJA1052i to an undervoltage on
DD2. The microcontroller cannot switch the transceiver directly to Standby mode. The
TJA1052i switches to Standby mode during VDD2 power-up and power-down. See
V
Section 7.2.2 for a description of undervoltage protection on VDD2
.
7.2 Fail-safe features
7.2.1 TXD dominant time-out function
A ‘TXD dominant time-out’ timer is started when pin TXD goes LOW. If the LOW state on
TXD persists for longer than tto(dom)TXD, the transmitter is disabled, releasing the bus lines
to recessive state. This function prevents a hardware and/or software application failure
from driving the bus lines to a permanent dominant state (blocking all network
communications). The TXD dominant time-out timer is reset by a positive edge on TXD.
The TXD dominant time-out time also defines the minimum possible bit rate of 40 kbit/s.
7.2.2 Undervoltage protection: VDD2
If the voltage on pin VDD2 falls below the standby threshold, Vuvd(stb)(VDD2), the transceiver
switches to Standby mode. In Standby mode, the transceiver is not able to transmit or
receive data on the bus lines. The transmitter and the Normal mode receiver are switched
off and the bus lines are biased to ground to minimize the supply current. The TJA1052i
TJA1052I
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 2 — 12 July 2013
5 of 20
TJA1052i
NXP Semiconductors
Galvanically isolated high-speed CAN transceiver
will remain in Standby mode until VDD2 rises above Vuvd(stb)(VDD2) (max). The low-power
receiver continues to monitor the bus while the TJA1052i is in Standby mode. Data on the
bus is still reflected onto RXD, but the transfer speed is reduced.
If the voltage on VDD2 falls below the switch-off threshold, Vuvd(swoff)(VDD2), the transceiver
switches off and disengages from the bus (zero load). It is guaranteed to switch on again
in Standby mode when VDD2 rises above Vuvd(swoff)(VDD2) (max).
7.2.3 Undervoltage protection: VDD1
If the voltage on pin VDD1 falls below the undervoltage detection threshold, Vuvd(VDD1), the
CAN bus switches to dominant state and the TXD dominant timeout timer is started. RXD
will not go high again until the supply voltage has been restored on VDD1 (VDD1
uvd(VDD1)).
>
V
7.2.4 Overtemperature protection
The output drivers are protected against overtemperature conditions. If the virtual junction
temperature exceeds the shutdown junction temperature, Tj(sd), the output drivers are
disabled. They are enabled again when the virtual junction temperature falls below Tj(sd)
and TXD is HIGH. Including the TXD condition ensures that output driver oscillation due to
temperature drift is avoided.
7.3 Insulation characteristics and safety-related specifications
Table 6.
Symbol
dL(IO1)
dL(IO2)
Rins
Isolator characteristics
Parameter
Conditions
Min
8.6
8.1
100
10
2
Typ
Max
Unit
mm
mm
G
G
-
[1]
[2]
[3]
[3]
minimum air gap
-
-
-
-
-
-
-
-
-
-
-
-
minimum external tracking
insulation resistance
VIO = 500 V at TA = 125 C
VIO = 500 V at TA = 150 C
-
-
pollution degree
-
material group (IEC 60664)
2
-
[1] Based on the measured data in the package outline. dL(IO1) is the clearance distance. Note that the clearance distance cannot be larger
than the creepage distance (dL(IO2)).
[2] Based on the measured data in the package outline. dL(IO2) is the creepage distance. According to IEC 60950-1, normative annex F
(also IEC60664 chapter 6.2, Example 11), the effective minimum external tracking is 1.0 mm less due to the presence of an intervening,
unconnected conductive part.
[3] Guaranteed by design.
TJA1052I
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 2 — 12 July 2013
6 of 20
TJA1052i
NXP Semiconductors
Galvanically isolated high-speed CAN transceiver
Table 7.
Working voltages and isolation
Insulation Characteristics
Parameter
Standard
TJA1052i/1
300 VRMS
420 Vpeak
2500 Vpeak
TJA1052i/2
450 VRMS
630 Vpeak
4000 Vpeak
TJA1052i/5
800 VRMS
max. working insulation voltage IEC 60664
[1]
per IEC 60664 (VIORM
)
1120 Vpeak
6000 Vpeak
max. transient overvoltage per
tTEST = 1.2/50 s (certification)
IEC 60664
[2]
IEC 60664 (VIOTM
)
rated insulation voltage per
UL 1577 (VISO
UL 1577
)
tTEST = 60 s (qualification)
tTEST = 1 s (production)
1000 VRMS
1200 VRMS
2500 VRMS
3000 VRMS
5000 VRMS
6000 VRMS
Insulation classification in terms of Overvoltage Category[3]
Insulation type
basic insulation[4]
Max. working voltage
150 VRMS
TJA1052i/1
TJA1052i/2
TJA1052i/5
I - IV
I - IV
I - III
I - II
I - III
I - IV
I - III
I - II
-
300 VRMS
I - II
600 VRMS
I
1000 VRMS
150 VRMS
-
reinforced insulation[4]
I - II
I - III
I - II
I
I - IV
I - III
I - II
300 VRMS
I
600 VRMS
-
-
1000 VRMS
-
I
[1] The working voltage is the input-to-output voltage that can be applied without time limit. Which TJA1052i variant should be selected
depends on the overvoltage category and the related insulation voltage.
[2] UL stress test is performed at higher than IEC-specified levels.
[3] Based on transient overvoltages as indicated in IEC60664; creepage and clearance distances not taken into account.
[4] Reinforced insulation should have an impulse withstand voltage one step higher than that specified for basic insulation.
Table 8.
Safety approvals
Standard
IEC 60950
File number
CB NL-25981
IEC 61010-1 2nd Edition
UL1577
CB NL-25982
compliancy check pending
TJA1052I
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 2 — 12 July 2013
7 of 20
TJA1052i
NXP Semiconductors
Galvanically isolated high-speed CAN transceiver
8. Limiting values
Table 9.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). All voltages and currents are referenced to GND2
unless otherwise specified.
Symbol Parameter
Conditions
Min
58
58
0.3
0.3
0.3
0.3
-
Max
Unit
V
VCANH
VCANL
VDD1
VDD2
VI
voltage on pin CANH
no time limit; DC value
no time limit; DC value
+58
voltage on pin CANL
supply voltage 1
supply voltage 2
input voltage
+58
V
[1]
+6.0
V
+6.0
V
[1]
[1]
[1]
on pin TXD
VDD1 + 0.3
VDD1 + 0.3
10
V
VO
output voltage
on pin RXD
V
IO
output current
on pin RXD
mA
V
Vtrt
transient voltage
electrostatic discharge voltage
on pins CANH and CANL
IEC 61000-4-2
at pins CANH and CANL
HBM
150
+100
[2]
[3]
[4]
VESD
8
+8
kV
at pins CANH and CANL[5]
at any other pin
MM
8
4
+8
+4
kV
kV
[6]
[7]
at any pin
300
+300
V
CDM
at corner pins
at any pin
750
500
40
+750
+500
+150
+125
+150
V
V
[8]
Tvj
virtual junction temperature
ambient temperature
storage temperature
C
C
C
Tamb
Tstg
40
65
[1] Referenced to GND1.
[2] IEC 61000-4-2 (150 pF, 330 ); direct coupling.
[3] ESD performance of pins CANH and CANL according to IEC 61000-4-2 (150 pF, 330 ) has been verified by an external test house.
The result is equal to or better than 8 kV (unaided).
[4] Human Body Model (HBM): according to AEC-Q100-002 (100 pF, 1.5 k).
[5] 8 kV to GND2 and VDD2; 6 kV to GND1.
[6] Machine Model (MM): according to AEC-Q100-003 (200 pF, 0.75 H, 10 ).
[7] Charged Device Model (CDM): according to AEC-Q100-011 (field Induced charge; 4 pF); grade C3B.
[8] An alternative definition of virtual junction temperature is: Tvj = Tamb + P Rth(vj-a), where Rth(vj-a) is a fixed value used in the calculation
of Tvj. The rating for Tvj limits the allowable combinations of power dissipation (P) and ambient temperature (Tamb).
9. Thermal characteristics
Table 10. Thermal characteristics
According to IEC 60747-1.
Symbol Parameter
Conditions
Value
Unit
Rth(vj-a)
thermal resistance from virtual junction to in free air
ambient
100
K/W
TJA1052I
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 2 — 12 July 2013
8 of 20
TJA1052i
NXP Semiconductors
Galvanically isolated high-speed CAN transceiver
10. Static characteristics
Table 11. Static characteristics
Tvj = 40 C to +150 C; VDD1 = 3.0 V to 5.25 V; VDD2 = 4.75 V to 5.25 V unless otherwise specified. Positive currents flow
into the IC. All voltages and currents are referenced to GND2 unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
DC supplies; pin VDD1 and VDD2
[1]
[1]
IDD1
supply current 1
supply current 2
VDD1 = 3 V to 5 V; VDD2 = 5 V;
VTXD = 0 V; bus dominant
-
-
-
-
-
-
2.6
5.6
70
mA
mA
mA
VDD1 = 3 V to 5 V; VDD2 = 5 V;
VTXD = VDD1; bus recessive
IDD2
VDD1 = 3 V to 5 V; VDD2 = 5 V;
VTXD = 0 V; bus dominant;
RL = 60
V
V
DD1 = 3 V to 5 V; VDD2 = 5 V;
TXD = VDD1; bus recessive
-
-
-
-
-
10
mA
V
Vuvd(stb)(VDD2)
standby undervoltage
3.5
1.3
1.3
4.75
2.7
2.7
detection voltage on pin VDD2
Vuvd(swoff)(VDD2) switch-off undervoltage
detection voltage on pin VDD2
V
[1]
[1]
Vuvd(VDD1)
undervoltage detection
voltage on pin VDD1
V
Vuvhys
undervoltage hysteresis
voltage
on pin VDD1
on pin VDD2
40
80
-
-
100
200
mV
mV
CAN transmit data input; pin TXD
VIH
VIL
ILI
HIGH-level input voltage
2.0
0
-
-
-
VDD1
0.8
V
LOW-level input voltage
input leakage current
V
10
+10
A
CAN receive data output; pin RXD
VOH
HIGH-level output voltage
IOH = 4 mA
VDD1
0.4
-
-
-
V
V
VOL
LOW-level output voltage
IOL = 4 mA
-
0.4
Standby mode control input; pin STB
VIH
HIGH-level input voltage
0.7VCC
-
VCC
0.3
+
V
VIL
IIH
IIL
LOW-level input voltage
HIGH-level input current
LOW-level input current
0.3
1
-
-
-
0.3VCC
+1
V
VSTB = VCC
VSTB = 0 V
A
A
15
1
Bus lines; pins CANH and CANL
VO(dom)
dominant output voltage
VTXD = 0 V; t < tto(dom)TXD
pin CANH
2.75
0.5
3.5
1.5
-
4.5
V
pin CANL
2.25
+400
V
Vdom(TX)sym
transmitter dominant voltage Vdom(TX)sym
=
400
mV
symmetry
VCC VCANH VCANL
TJA1052I
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 2 — 12 July 2013
9 of 20
TJA1052i
NXP Semiconductors
Galvanically isolated high-speed CAN transceiver
Table 11. Static characteristics …continued
Tvj = 40 C to +150 C; VDD1 = 3.0 V to 5.25 V; VDD2 = 4.75 V to 5.25 V unless otherwise specified. Positive currents flow
into the IC. All voltages and currents are referenced to GND2 unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VO(dif)bus
bus differential output voltage VTXD = 0 V; t < tto(dom)TXD
1.5
-
3
V
RL = 45 to 65
VTXD = VCC recessive; no load
50
-
+50
3
mV
V
VO(rec)
recessive output voltage
Normal mode; VTXD = VCC; no load
2
0.5VCC
[2]
[3]
Vth(RX)dif
differential receiver threshold Vcm(CAN) = 25 V to +25 V
voltage
Normal mode
0.5
0.4
-
-
0.9
V
V
Standby mode;
1.15
Vcm(CAN) = 12 V to +12 V
Vhys(RX)dif
IO(dom)
differential receiver hysteresis Vcm(CAN) = 25 V to +25 V
-
165
-
mV
voltage
Normal mode
dominant output current
VTXD = 0 V; t < tto(dom)TXD;
VDD2 = 5 V
pin CANH; VCANH = 0 V
100
40
70
70
-
40
100
+5
mA
mA
mA
pin CANL; VCANL = 5 V / 40 V
IO(rec)
recessive output current
Normal mode; VTXD = VDD1
5
VCANH = VCANL = 27 V to +32 V
IL
leakage current
VDD2 = 0 V; VCANH = VCANL = 5 V
between VCANH and VCANL
3
9
-
+3
28
+3
52
20
A
k
%
Ri
input resistance
15
-
Ri
Ri(dif)
Ci(cm)
input resistance deviation
differential input resistance
3
19
-
30
-
k
pF
[4]
[4]
common-mode input
capacitance
Ci(dif)
differential input capacitance
-
-
-
10
-
pF
Temperature detection
Tj(sd) shutdown junction
temperature
[4]
[5]
190
C
[1] Referenced to GND1.
[2] cm(CAN) is the common mode voltage of CANH and CANL.
V
[3] Standby mode entered when VDD2 falls below Vuvd(stb)(VDD2)
.
[4] Guaranteed by design.
[5] RXD is LOW during thermal shutdown.
TJA1052I
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 2 — 12 July 2013
10 of 20
TJA1052i
NXP Semiconductors
Galvanically isolated high-speed CAN transceiver
11. Dynamic characteristics
Table 12. Dynamic characteristics
Tvj = 40 C to +150 C; VDD1 = 3.0 V to 5.25 V; VDD2 = 4.75 V to 5.25 V unless specified otherwise
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Transceiver timing; pins CANH, CANL, TXD and RXD; see Figure 3
td(TXD-busdom) delay time from TXD to bus dominant
td(TXD-busrec) delay time from TXD to bus recessive
td(busdom-RXD) delay time from bus dominant to RXD
td(busrec-RXD) delay time from bus recessive to RXD
Normal mode
-
72
97
67
72
-
120
120
130
130
220
5
ns
Normal mode
-
ns
Normal mode
-
ns
Normal mode
-
ns
tPD(TXD-RXD)
tto(dom)TXD
fdata
propagation delay from TXD to RXD
TXD dominant time-out time
data rate
Normal mode
72
0.3
0.04
20
-
ns
VTXD = 0 V; Normal mode
1.7
-
ms
Mbps
kV/s
s
1.0
-
[1]
[2]
CMTI
common-mode transient immunity
start-up time
VI = VDD1 or VI = 0 V
45
-
tstartup
500
[1] See Figure 5.
[2] The start-up time is the time from the application of power to valid data at the output. Guaranteed by design.
HIGH
TXD
LOW
CANH
CANL
dominant
0.9 V
V
O(dif)(bus)
0.5 V
recessive
HIGH
0.7V
IO
RXD
0.3V
IO
LOW
t
t
d(TXD-busrec)
d(TXD-busdom)
t
t
d(busrec-RXD)
d(busdom-RXD)
t
t
PD(TXD-RXD)
PD(TXD-RXD)
015aaa169
Fig 3. CAN transceiver timing diagram
TJA1052I
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 2 — 12 July 2013
11 of 20
TJA1052i
NXP Semiconductors
Galvanically isolated high-speed CAN transceiver
12. Application information
Isolated CAN applications are becoming increasingly common in electric and hybrid
electric vehicles. The TJA1052i is the ideal solution in applications that require an isolated
CAN node, such as Li-ion battery management, regenerative braking and 48 V-to-12 V
level shifting. The device can also be used to isolate high-voltage on-demand pumps and
motors in belt elimination projects.
If the TJA1052i is used in a HS-CAN network that supports remote bus wake-up, the
power-down sequence of the supplies must be managed properly to avoid a dominant
pulse on the CAN bus. VDD2 should pass the minimum undervoltage threshold
(Vuvd(stb)(VDD2) (min)) before VDD1 falls below its maximum undervoltage detection
threshold (Vuvd(VDD1)(max)). Power-up sequencing can happen in any order.
Digital inputs and outputs are 3 V compliant, allowing the TJA1052i to interface directly
with 3 V and 5 V microcontrollers.
isolated supply
5 V
5 V
BAT
V
V
DD1
DD2
V
CANH
CANL
TXD
RXD
DD
TX0
RX0
CANH
CANL
MICRO-
CONTROLLER
TJA1052I
GND
STB GND2
GND1
015aaa340
Fig 4. Typical application with TJA1052i and a 5 V microcontroller.
13. Test information
13.1 Quality information
This product has been qualified in accordance with the Automotive Electronics Council
(AEC) standard Q100 Rev-G - Failure mechanism based stress test qualification for
integrated circuits, and is suitable for use in automotive applications.
TJA1052I
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 2 — 12 July 2013
12 of 20
TJA1052i
NXP Semiconductors
Galvanically isolated high-speed CAN transceiver
13.2 Test circuits
9''ꢂ
9''ꢃ
9''ꢂ
*1'ꢂ
7;'
QꢆFꢆ
9''ꢃ
/&ꢁILOWHU
VXSSO\
ꢂ
ꢃ
ꢇ
ꢈ
ꢀ
ꢄ
ꢉ
ꢊ
ꢂꢄ
ꢂꢀ
ꢂꢈ
ꢂꢇ
ꢂꢃ
ꢂꢂ
ꢂꢅ
ꢋ
*1'ꢃ
67%
648$5(
:$9(
*(1(5$725
%$7
ꢀꢁ9
&$1+
&$1/
9''ꢃ
QꢆFꢆ
7-$ꢀꢁꢂꢃ,
ꢄꢅꢁȍ
5;'
QꢆFꢆ
QꢆFꢆ
*1'ꢂ
*1'ꢃ
/&ꢁILOWHU
7(67ꢁ%2$5'
*1'ꢃ
*1'ꢂ
6&23(
38/6(
*(1(5$725
DDDꢀꢁꢁꢂꢁꢃꢄ
Fig 5. CMTI test setup
+5 V
47 µF
100 nF
V
DD1
V
DD2
TXD
CANH
R
L
100 pF
TJA1052I
RXD
CANL
GND1
GND2
STB
15 pF
015aaa339
Fig 6. Timing test circuit for CAN transceiver
TJA1052I
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 2 — 12 July 2013
13 of 20
TJA1052i
NXP Semiconductors
Galvanically isolated high-speed CAN transceiver
14. Package outline
SO16: plastic small outline package; 16 leads; body width 7.5 mm
SOT162-1
D
E
A
X
c
H
v
M
A
E
y
Z
16
9
Q
A
2
A
(A )
3
A
1
pin 1 index
θ
L
p
L
1
8
detail X
e
w
M
b
p
0
5
10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
A
max.
(1)
(1)
(1)
UNIT
mm
A
A
A
b
c
D
E
e
H
L
L
Q
v
w
y
θ
1
2
3
p
E
p
Z
0.3
0.1
2.45
2.25
0.49
0.36
0.32
0.23
10.5
10.1
7.6
7.4
10.65
10.00
1.1
0.4
1.1
1.0
0.9
0.4
2.65
0.1
0.25
0.01
1.27
0.05
1.4
0.25 0.25
0.1
8o
0o
0.012 0.096
0.004 0.089
0.019 0.013 0.41
0.014 0.009 0.40
0.30
0.29
0.419
0.394
0.043 0.043
0.016 0.039
0.035
0.016
inches
0.055
0.01 0.01 0.004
Note
1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
JEITA
99-12-27
03-02-19
SOT162-1
075E03
MS-013
Fig 7. Package outline SOT162-1 (SO16)
TJA1052I
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 2 — 12 July 2013
14 of 20
TJA1052i
NXP Semiconductors
Galvanically isolated high-speed CAN transceiver
15. Handling information
All input and output pins are protected against ElectroStatic Discharge (ESD) under
normal handling. When handling ensure that the appropriate precautions are taken as
described in JESD625-A or equivalent standards.
16. Soldering of SMD packages
This text provides a very brief insight into a complex technology. A more in-depth account
of soldering ICs can be found in Application Note AN10365 “Surface mount reflow
soldering description”.
16.1 Introduction to soldering
Soldering is one of the most common methods through which packages are attached to
Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both
the mechanical and the electrical connection. There is no single soldering method that is
ideal for all IC packages. Wave soldering is often preferred when through-hole and
Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not
suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high
densities that come with increased miniaturization.
16.2 Wave and reflow soldering
Wave soldering is a joining technology in which the joints are made by solder coming from
a standing wave of liquid solder. The wave soldering process is suitable for the following:
• Through-hole components
• Leaded or leadless SMDs, which are glued to the surface of the printed circuit board
Not all SMDs can be wave soldered. Packages with solder balls, and some leadless
packages which have solder lands underneath the body, cannot be wave soldered. Also,
leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered,
due to an increased probability of bridging.
The reflow soldering process involves applying solder paste to a board, followed by
component placement and exposure to a temperature profile. Leaded packages,
packages with solder balls, and leadless packages are all reflow solderable.
Key characteristics in both wave and reflow soldering are:
• Board specifications, including the board finish, solder masks and vias
• Package footprints, including solder thieves and orientation
• The moisture sensitivity level of the packages
• Package placement
• Inspection and repair
• Lead-free soldering versus SnPb soldering
16.3 Wave soldering
Key characteristics in wave soldering are:
TJA1052I
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 2 — 12 July 2013
15 of 20
TJA1052i
NXP Semiconductors
Galvanically isolated high-speed CAN transceiver
• Process issues, such as application of adhesive and flux, clinching of leads, board
transport, the solder wave parameters, and the time during which components are
exposed to the wave
• Solder bath specifications, including temperature and impurities
16.4 Reflow soldering
Key characteristics in reflow soldering are:
• Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to
higher minimum peak temperatures (see Figure 8) than a SnPb process, thus
reducing the process window
• Solder paste printing issues including smearing, release, and adjusting the process
window for a mix of large and small components on one board
• Reflow temperature profile; this profile includes preheat, reflow (in which the board is
heated to the peak temperature) and cooling down. It is imperative that the peak
temperature is high enough for the solder to make reliable solder joints (a solder paste
characteristic). In addition, the peak temperature must be low enough that the
packages and/or boards are not damaged. The peak temperature of the package
depends on package thickness and volume and is classified in accordance with
Table 13 and 14
Table 13. SnPb eutectic process (from J-STD-020D)
Package thickness (mm) Package reflow temperature (C)
Volume (mm3)
< 350
235
350
220
< 2.5
2.5
220
220
Table 14. Lead-free process (from J-STD-020D)
Package thickness (mm) Package reflow temperature (C)
Volume (mm3)
< 350
260
350 to 2000
> 2000
260
< 1.6
260
250
245
1.6 to 2.5
> 2.5
260
245
250
245
Moisture sensitivity precautions, as indicated on the packing, must be respected at all
times.
Studies have shown that small packages reach higher temperatures during reflow
soldering, see Figure 8.
TJA1052I
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 2 — 12 July 2013
16 of 20
TJA1052i
NXP Semiconductors
Galvanically isolated high-speed CAN transceiver
maximum peak temperature
= MSL limit, damage level
temperature
minimum peak temperature
= minimum soldering temperature
peak
temperature
time
001aac844
MSL: Moisture Sensitivity Level
Fig 8. Temperature profiles for large and small components
For further information on temperature profiles, refer to Application Note AN10365
“Surface mount reflow soldering description”.
17. Revision history
Table 15. Revision history
Document ID
TJA1052I v.2
Modifications:
Release date
20130712
Data sheet status
Change notice
Supersedes
Product data sheet
-
TJA1052I v.1
• Section 2.1: text revised
• Table 12: Table note 1 added
• Figure 5: added
TJA1052I v.1
20130424
Product data sheet
-
-
TJA1052I
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 2 — 12 July 2013
17 of 20
TJA1052i
NXP Semiconductors
Galvanically isolated high-speed CAN transceiver
18. Legal information
18.1 Data sheet status
Document status[1][2]
Product status[3]
Development
Definition
Objective [short] data sheet
This document contains data from the objective specification for product development.
This document contains data from the preliminary specification.
This document contains the product specification.
Preliminary [short] data sheet Qualification
Product [short] data sheet Production
[1]
[2]
[3]
Please consult the most recently issued document before initiating or completing a design.
The term ‘short data sheet’ is explained in section “Definitions”.
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
Suitability for use in automotive applications — This NXP
18.2 Definitions
Semiconductors product has been qualified for use in automotive
applications. Unless otherwise agreed in writing, the product is not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors and its suppliers accept no liability for
inclusion and/or use of NXP Semiconductors products in such equipment or
applications and therefore such inclusion and/or use is at the customer's own
risk.
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
18.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information. NXP Semiconductors takes no
responsibility for the content in this document if provided by an information
source outside of NXP Semiconductors.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
TJA1052I
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 2 — 12 July 2013
18 of 20
TJA1052i
NXP Semiconductors
Galvanically isolated high-speed CAN transceiver
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
Quick reference data — The Quick reference data is an extract of the
product data given in the Limiting values and Characteristics sections of this
document, and as such is not complete, exhaustive or legally binding.
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from competent authorities.
18.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
19. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
TJA1052I
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 2 — 12 July 2013
19 of 20
TJA1052i
NXP Semiconductors
Galvanically isolated high-speed CAN transceiver
20. Contents
1
General description. . . . . . . . . . . . . . . . . . . . . . 1
20
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2
Features and benefits . . . . . . . . . . . . . . . . . . . . 1
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Power management . . . . . . . . . . . . . . . . . . . . . 2
Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.1
2.2
2.3
3
4
5
Quick reference data . . . . . . . . . . . . . . . . . . . . . 2
Ordering information. . . . . . . . . . . . . . . . . . . . . 2
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3
6
6.1
6.2
Pinning information. . . . . . . . . . . . . . . . . . . . . . 4
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4
7
7.1
Functional description . . . . . . . . . . . . . . . . . . . 5
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Normal mode . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Standby mode. . . . . . . . . . . . . . . . . . . . . . . . . . 5
Fail-safe features . . . . . . . . . . . . . . . . . . . . . . . 5
TXD dominant time-out function. . . . . . . . . . . . 5
Undervoltage protection: VDD2 . . . . . . . . . . . . . 5
Undervoltage protection: VDD1 . . . . . . . . . . . . . 6
Overtemperature protection . . . . . . . . . . . . . . . 6
Insulation characteristics and safety-related
7.1.1
7.1.2
7.2
7.2.1
7.2.2
7.2.3
7.2.4
7.3
specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 6
8
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 8
Thermal characteristics . . . . . . . . . . . . . . . . . . 8
Static characteristics. . . . . . . . . . . . . . . . . . . . . 9
Dynamic characteristics . . . . . . . . . . . . . . . . . 11
Application information. . . . . . . . . . . . . . . . . . 12
9
10
11
12
13
13.1
13.2
Test information. . . . . . . . . . . . . . . . . . . . . . . . 12
Quality information . . . . . . . . . . . . . . . . . . . . . 12
Test circuits. . . . . . . . . . . . . . . . . . . . . . . . . . . 13
14
15
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 14
Handling information. . . . . . . . . . . . . . . . . . . . 15
16
Soldering of SMD packages . . . . . . . . . . . . . . 15
Introduction to soldering . . . . . . . . . . . . . . . . . 15
Wave and reflow soldering . . . . . . . . . . . . . . . 15
Wave soldering. . . . . . . . . . . . . . . . . . . . . . . . 15
Reflow soldering. . . . . . . . . . . . . . . . . . . . . . . 16
16.1
16.2
16.3
16.4
17
Revision history. . . . . . . . . . . . . . . . . . . . . . . . 17
18
Legal information. . . . . . . . . . . . . . . . . . . . . . . 18
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 18
Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 19
18.1
18.2
18.3
18.4
19
Contact information. . . . . . . . . . . . . . . . . . . . . 19
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2013.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
Date of release: 12 July 2013
Document identifier: TJA1052I
相关型号：
©2020 ICPDF网 联系我们和版权申明