H3CR-FN-300 [OMRON]
Analog Circuit,;
| 型号： | H3CR-FN-300 |
| 厂家： | 
OMRON ELECTRONICS LLC |
| 描述： | Analog Circuit, |
| 文件： | 总13页 (文件大小：273K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
IIH3CR-F
Solid-state Twin Timers
DIN 48 x 48-mm Solid-state Twin Timers
Wide power supply ranges of 100 to 240 VAC and
48 to 125 VDC respectively.
Independent ON- and OFF-time settings. Further-
more, combinations of long ON- or OFF-time and
short OFF- or ON-time settings are possible.
Fourteen time ranges from 0.05 s to 30 h or from
1.2 s to 300 h depending on the model to be used.
Models with a flicker ON start or flicker OFF start
are available.
Easy sequence checks through instantaneous
outputs for a zero set value at any time range.
Only 80 mm long when panel-mounted with a
socket.
11-pin and 8-pin models are available.
Ordering Information
Supply voltage
0.05 s to 30 h models
11-pin models 8-pin models
1.2 s to 300 h models
Operating
modes
11-pin models
8-pin models
Flicker OFF start
100 to 240 VAC
24 VAC/DC
12 VDC
H3CR-F
H3CR-F8
H3CR-F-300
H3CR-F8-300
48 to 125 VDC
100 to 240 VAC
24 VAC/DC
12 VDC
Flicker ON start
H3CR-FN
H3CR-F8N
H3CR-FN-300
H3CR-F8N-300
48 to 125 VDC
Note: Specify both the model number and supply voltage when ordering.
Example: H3CR-F 24 VAC/DC
Supply voltage
Model Number Legend:
H3CR -
-
1
2
3
4
1. Classification
F: Twin timers
3. Twin Timer Mode
None: Flicker OFF start
N:
4. Specified Type
300: Long time range (1.2 s to 300 h) type
Flicker ON start
2. Configuration
None: 11-pin socket
8:
8-pin socket
1
H3CR-F
H3CR-F
Accessories (Order Separately)
Name/specifications
Models
Flush Mounting Adapter
Y92F-30
Y92F-73
Y92F-74
PFP-50N
PFP-100N
PFP-100N2
PFP-M
Mounting Track
50 cm (l) x 7.3 mm (t)
1 m (l) x 7.3 mm (t)
1 m (l) x 16 mm (t)
End Plate
Spacer
PFP-S
Protective Cover
Y92A-48B
P2CF-08
P2CF-11
P3G-08
Track Mounting/
Front Connecting Socket
8-pin
11-pin
Back Connecting Socket
Hold-down Clip
8-pin
11-pin
P3GA-11
Y92H-7
For PL08 and PL11 Sockets
For PF085A Socket
Y92H-8
Specifications
General
Item
Operating mode
Pin type
H3CR-F
H3CR-F8
H3CR-FN
H3CR-F8N
Flicker OFF start
11-pin
Flicker ON start
11-pin
8-pin
8-pin
Operating/Reset method
Output type
Time-limit operation/Time-limit reset or self-reset
Relay output (DPDT)
Mounting method
EMC
DIN track mounting, surface mounting, and flush mounting
Emission Enclosure:
Emission AC Mains:
Immunity ESD:
EN55011 Group 1 class A
EN55011 Group 1 class A
IEC801-2: 4 kV contact discharge (level 2)
8 kV air discharge (level 3)
Immunity RF-interference:
ENV50140: 10 V/m (80 MHz to 1 GHz) (level 3)
Immunity Conducted Disturbance: ENV50141: 10 V (0.15 to 80 MHz) (level 3)
Immunity Burst:
IEC801-4: 2 kV power-line (level 3)
2 kV I/O signal-line (level 4)
Approved standards
UL508, CSA C22.2 No.14, LR/NK
Conforms to VDE0435/2021, VDE0110
Conforms to EN50081-2, prEN50082-2
Time Ranges
0.05 s to 30 h Models
Time unit
s (sec)
0.05 to 1.2
x10 s (10 s)
min
h (hrs)
Setting
1.2
3
1.2 to 12
3 to 30
0.12 to 1.2
0.3 to 3
0.3 to 3
1.2 to 12
3 to 30
12
30
12 to 120
30 to 300
1.2 to 12
3 to 30
Note: Instantaneous output is available at any time range. To obtain instantaneous output, set to below 0.
1.2 s to 300 h Models
Time unit
Setting
x10 s (10 s)
1.2 to 12
x10 min (10 min)
1.2 to 12
h (hrs)
0.12 to 1.2
x10 h (10 h)
1.2
3
1.2 to 12
3 to 30
3 to 30
0.3 to 3
1.2 to 12
3 to 30
3 to 30
12
30
12 to 120
30 to 300
12 to 120
30 to 300
12 to 120
30 to 300
Note: Instantaneous output is available at any time range. To obtain instantaneous output, set to below 0.
2
H3CR-F
H3CR-F
Ratings
Rated supply voltage (see note)
Operating voltage range
Power reset
100 to 240 VAC (50/60 Hz),12 VDC, 24 VAC/DC (50/60 Hz), 48 to 125 VDC
85% to 110% of rated supply voltage; 90% to 110% with 12-VDC models
Minimum power-opening time: 0.1 s
Power consumption
100 to 240 VAC: approx. 10 VA; 12 VDC: approx. 1 W;
24 VAC/DC: approx. 2 VA (AC), approx. 1 W (DC); 48 to 125 VDC: approx. 1.5 W
Control outputs
Contact output: 5 A at 250 VAC, resistive load (cosφ = 1)
Note: A power supply with a ripple of 20% max. (single-phase power supply with full-wave rectification) can be used with each DC Model.
Characteristics
Accuracy of operating time
±0.3% FS max. (±0.3% FS ±10 ms in ranges of 1.2 and 3 s)
±5% FS ±0.05 s max.
Setting error
Reset time
0.1 s max.
Influence of voltage
Influence of temperature
Insulation resistance
Dielectric strength
±0.5% FS max. (±0.5% FS ±10 ms in ranges of 1.2 and 3 s)
±2% FS max. (±2% FS ±10 ms in ranges of 1.2 and 3s)
100 MΩ min. (at 500 VDC)
2,000 VAC, 50/60 Hz for 1 min (between current-carrying metal parts and exposed
non-current-carrying metal parts)
2,000 VAC, 50/60 Hz for 1 min (between control output terminals and operating circuit)
1,000 VAC, 50/60 Hz for 1 min (between contacts not located next to each other)
Impulse withstand voltage
Noise immunity
3 kV (between power terminals) for 100 to 240 VAC, 48 to 125 VDC
1 kV for 12 VDC, 24 VAC/DC
4.5 kV (between current-carrying terminal and exposed non-current-carrying metal parts)
for 100 to 240 VAC, 48 to 125 VDC
1.5 kV for 12 VDC, 24 VAC/DC
±1.5 kV (between power terminals), square-wave noise by noise simulator (pulse width:
100 ns/1 µs, 1-ns rise)
±400 V for 12 VDC
Static immunity
Malfunction:8 kV
Destruction: 15 kV
Vibration resistance
Shock resistance
Ambient temperature
Destruction:10 to 55 Hz with 0.75-mm single amplitude each in three directions
Malfunction:10 to 55 Hz with 0.5-mm single amplitude each in three directions
2
Destruction: 980 m/s (100G) each in three directions
2
Malfunction:98 m/s (10G) each in three directions
Operating:–10°C to 55°C (with no icing)
Storage: –25°C to 65°C (with no icing)
Ambient humidity
Life expectancy
Operating: 35% to 85%
Mechanical:20 million operations min. (under no load at 1,800 operations/h)
Electrical: 100,000 operations min. (5 A at 250 VAC, resistive load at 1,800 operations/h)
Case color
Light Gray (Munsell 5Y7/1)
IEC: IP40
Enclosure ratings
Weight
Approx. 100 g
Engineering Data
10,000
5,000
1,000
Reference: A maximum current of 0.15 A can be switched at 125 VDC (cosφ = 1)
30 VDC L/R = 7 ms
500
and a maximum current of 0.1 A can be switched if L/R is 7 ms. In
250 VAC/30 VDC
(cosφ = 1)
both cases, a life of 100,000 operations can be expected.
The minimum applicable load is 10 mA at 5 VDC (failure level: P).
100
250 VAC (cosφ = 0.4)
Load current (A)
3
H3CR-F
H3CR-F
Nomenclature
OFF indicator (green)
LitwhentheoutputisOFF.
OFF-time unit display window
OFF-time unit selector (select one from sec.
10 s, min., and hrs, or from 10 s, 10 min, hrs,
and 10 h)
ON indicator (orange)
Lit when the output is ON.
Scale range display
windows
ON-time setting knob (with orange pointer)
For ON-time setting
OFF-time setting knob (with green pointer)
For OFF-time setting
Time range selector (select one
from 1.2, 3, 12, and 30)
ON-time unit display window
For both ON-time and OFF-time.
ON-time unit selector (select one
from sec. 10 s, min., and hrs, or from
10 s, 10 min, hrs, and 10 h)
Operation
Block Diagrams
Zero setting
detection
circuit
ON indicator OFF indicator
Indicator
circuit
ROM
RAM
Clock
Output
circuit
Power supply
circuit
Time range/unit
selectors
One-chip microcomputer
AC (DC) input
I/O Functions
Inputs
---
Outputs are turned ON/OFF according to the time set by the ON- and OFF-time setting knob.
Outputs
Control output
4
H3CR-F
H3CR-F
Timing Chart
Operating mode
Timing chart
Flicker OFF start
0.1 s min.
ON
Power
OFF
t
t
t
t
t
t
OFF
OFF
ON
OFF
ON
OFF
ON
indicator
Lit
Not lit
Lit
OFF
indicator
Not lit
ON
Output
NO
OFF
ON
Output
NC
OFF
t
t
:
ON set time
: OFF set time
ON
OFF
Flicker ON start
0.1 s min.
ON
Power
OFF
t
t
t
t
t
t
OFF
ON
OFF
ON
OFF
ON
Lit
ON
indicator
Not lit
Lit
OFF
indicator
Not lit
ON
Output
NO
OFF
ON
Output
NC
OFF
t
t
:
ON set time
: OFF set time
ON
OFF
5
H3CR-F
H3CR-F
Dimensions
Note: All units are in millimeters unless otherwise indicated.
17.4
5.7
66.6
52.3
H3CR-F
H3CR-FN
48
6
0.7
H3CR-F-300
H3CR-FN-300
44.8 x 44.8
37 dia
48
14 dia.
R1.3
17.4
5.7
66.6
52.3
H3CR-F8
H3CR-F8N
48
6
0.7
H3CR-F8-300
H3CR-F8N-300
44.8 x 44.8
37 dia
48
14 dia.
R1.3
Installation
Terminal Arrangement
H3CR-F8
H3CR-F8N
H3CR-F
H3CR-FN
H3CR-F8-300
H3CR-F8N-300
H3CR-F-300
H3CR-FN-300
(–)
(~)
(+)
(~)
(–)(~)
(+)(~)
Power supply
Power supply
Note: Leave terminals 5, 6, and 7 open.
Do not use them as relay terminals.
Operation
Note: The undermentioned is common for all H3CR-F/G/H models.
6
H3CR-F
H3CR-F
For OFF-time, the desired time unit (sec, 10 s, min, and hrs, or 10 s,
10 min, hrs, and 10 h) is indicated in the OFF-time unit display win-
dow at the upper right corner of the front panel and can be changed
by turning the OFF-time unit selector located below the OFF-time
unit display window.
Basic Setting
Setting of Selectors
The selectors can be turned clockwise and counterclockwise to se-
lect the desired time unit, time range, or operating mode.
Each selector has a snap mechanism that secures the selector at a
given position. Set the selector at a position at which it is secured.
Do not set it midway between two securing positions or a malfunc-
tion could result from improper setting.
Operating mode
selector
Operating mode
display window
Groove for
screwdriver
•
H3CR-G Star-delta Timers
(i.e., H3CR-A)
A star operation time range (0 to 6, 0 to 12, 0 to 60, or 0 to 120 sec-
onds) is selected with the star operation time range selector at the
lower left corner of the front panel.
Selection of Time Unit and Time Range
•
H3CR-F Twin Timers
A time range (0 to 1.2, 0 to 3, 0 to 12, or 0 to 30) is selected for ON-
and OFF-time using the time range selector at the lower left corner
of the front panel, and the selected time range appears within the
plastic frame of the time setting knob (= scale range display win-
dows).
The time required for switching (0.05, 0.1, 0.25, or 0.5 second) from
the star operation to the delta operation of the H3CR-G can be se-
lectedwith the star-delta transfer time selector at the lower right cor-
ner of the front panel.
For ON-time, the desired time unit (sec, 10 s, min, and hrs, or 10 s,
10 min, hrs, and 10 h) is indicated in the ON-time unit display win-
dow at the lower right corner of the front panel and can be changed
by turning the ON-time unit selector located below the ON-time unit
display window.
7
H3CR-F
H3CR-F
•
H3CR-H Power OFF-delay Timers
Atimerange(0to0.6, 0to1.2, 0to6, and0to12)isselectedwiththe
timerangeselectoratthelowerleftcornerofthefrontpanel. Notime
unit selector is available. When ordering the H3CR-H, specify S (for
the second unit) or M (for the minute unit) for your H3CR-H.
Dimensions
Note: The undermentioned is common for all H3CR-F/G/H models.
Note: All units are in millimeters unless otherwise indicated.
Dimensions with Flush Mounting Adaptor
Y92F-30
Panel
58
52
42
48
Panel Cutout
+0.6
–0
0.5 R max.
45
Note: The adapters for two or more timers mounted in a vertical line are different in ori-
(N)
entation from those mounted in a horizontal line.
N can be obtained as follows (n: the number of H3CR models arranged side by side)
+0.6
–0
+1
45
Without a Cover: N = (48n - 2.5)
With the Protective Cover: N = (51n - 5.5)
/
-0
+1
/
-0
+1
With the Panel Cover: N = (50n - 4.5)
/
-0
8
H3CR-F
H3CR-F
Dimensions with Flush Mounting Adaptor
Y92F-73/-70
Panel Cutout
Panel
Adapter mounting hole Two, 4.5 dia.
R0.5 max.
65 to 66
52 to 53
45±0
.15
88
76±0.2
45±0.15
58
Note: Themounting panel thickness
Dimensions with Flush Mounting Adaptor
Y92F-74/-71
should be 1 to 3.2 mm.
Panel
R0.5 max.
+0.5
–0
56
45
+0.5
–0
68
58
55
45±0.2
43±0.2
Note: Themounting panel thickness
+0.2
50
should be 1 to 3.2 mm.
–0
Track Mounting
11-pin,
short body
models:
11-pin, long
body
models:
eg.
8-pin, long
body
models:
9
111.7*
109.4
100.7*
98.4
2.3*
102.8
100.5
eg. H3CR-F
eg.
H3CR-HRL
H3CR-H8L
P2CF-08
P2CF-11
P2CF-08
P2CF-11
2.3*
2.3*
2.3*
*These dimensions vary with the kind of DIN track (reference value).
Flush Mounting
17
17
15
15
80
75
91.4
85.4
8-pin, long
body
models:
eg.
11-pin, long
body
models:
eg.
11-pin,
short body
models:
eg. H3CR-F
H3CR-H8L
H3CR-HRL
P3GA-11
P3G-08
P3GA-11
P3G-08
Y92F-30
Y92F-30
Y92F-30
Y92F-30
9
H3CR-F
H3CR-F
Accessories (Order Separately)
Track Mounting/
Front Connecting Socket
P2CF-08
Terminal Arrangement/
Internal Connections
(Top View)
Eight,
3
4.5
M3.5 x 7.5 sems
7.8
Surface Mounting Holes
Two, 4.5 dia. or two, M4
70 max.
35.4
Two, 4.5 dia.
holes
40±0.2
4
50 max.
20.3 max.
P2CF-11
3
4.5
Eleven,
M3.5 x 7.5 sems
Two, 4.5 dia. mounting holes
7.8
40±0.2
70 max.
35.4
Two, 4.5 dia.
holes
4
50 max.
31.2 max.
Back Connecting Socket
P3G-08
Terminal Arrangement/
Internal Connections
(Bottom View)
27 dia.
45
45
4.9
17
P3GA-11
27 dia.
45
25.6
6.2
4.5
45
16.3
Mounting Track
PFP-100N, PFP-50N
PFP-100N2
16
7.3±0.15
4.5
4.5
27
29.2
1.5
24
1
27±0.15
35±0.3
35±0.3
15 25
25
25
25 15
*
15 25
25
25
25
1
10
10
10
10
L
L
L: Length
1 m
50 cm
1 m
PFP-100N
PFP-50N
PFP-100N2
10
H3CR-F
H3CR-F
End Plate
PFP-M
Spacer
PFP-S
16
12
10
6.2
5
1.8
1
35.5 35.3
34.8
50
44.3
1.8
11.5
1.3
4.8
M4 x 8
pan head
screw
10
16.5
Y92A-48B
Protective Cover
Y92A-48B
The protective cover protects the front panel, particularly the time
setting section, against dust, dirt, and water. It also prevents the set
value from being altered due to accidental contact with the time set-
ting knob.
Note: 1. The Y92A-48B Protective Cover is made of a hard plas-
tic and therefore it must be removed to change the timer
set value.
2. The Protective Cover cannot be mounted if the Panel
Cover (sold separately) is used on the Timer.
Hold-down Clip
Y92H-7/-1
For PL08 and PL11 Sockets
Y92H-8/-2
For PF085A Socket
Precautions
Note: The undermentioned is common for all H3CR-F/G/H models.
Changing of Setting
NOTICE: Do not change the time unit, time range, or operation
mode while the timer is in operation or malfunction could
result.
Wiring (H3CR-H)
The H3CR has a high impedance circuit. Therefore, the H3CR may
not be reset if the H3CR is influenced by inductive voltage. In order
to eliminate any influence of inductive voltage, the wires connected
to the H3CR must be as short as possible and should not be
installed alongside power lines. If the H3CR is influenced by induc-
tive voltage that is 30% or more of the rated voltage, connect a CR
filter with a capacitance of approximately 0.1 µF and a resistance of
approximately 120 Ω or a bleeder resistor between the power sup-
ply terminals. If there is any residual voltage due to current leakage,
connect a bleeder resistor between the power supply terminals.
11
H3CR-F
H3CR-F
Operation (H3CR-H)
Power Supplies (H3CR-H)
An interval of 3 s minimum is required to turn on the H3CR after the
H3CR is turned off. If the H3CR is turned on and off repeatedly with
an interval of shorter than 3 s, the internal parts of the H3CR may
deteriorate and the H3CR may malfunction.
An AC power supply can be connected to the power input terminals
withoutregardingpolarity. ADCpowersupplymustbeconnectedto
the power input terminals as designated according to the polarity of
the terminals.
A DC power supply can be connected if its ripple factor is 20% or
less and the mean voltage is within the rated operating voltage
range of the Timer.
3 s min.
Power
Connect the power supply voltage through a relay or switch in such
a way that the voltage reaches a fixed value at once or the Timer
may not be reset or a timer error could result.
Output
state 1
For the power supply of an input device, use an isolating transform-
er, of which the primary and secondary windings are mutually iso-
lated and the secondary winding is not grounded.
Output
state 2
H3CR
After the forced reset function of the H3CR is activated, an interval
of 3 s minimum is required to activate the forced reset function
again. If the forced reset function is activated repeatedly with an in-
tervalofshorterthan3s, theinternalpartsoftheH3CRmaydeterio-
rate and the H3CR may malfunction.
Input
terminal
Power supply
Power
Circuit
3 s min.
3 s min.
Isolation transformer is required.
Reset
input
The H3CR-H has a large inrush current; provide sufficient power
supply capacity. If the power supply capacity is too small, there may
be delays in turning ON the output.
Output
If it is required that the output be turned on repeatedly with an inter-
val of shorter than 3 s, consider use of the H3CR-A in mode D (sig-
nal OFF-delay).
Inrush Current
Model
Voltage
24 VAC/DC
Applied voltage
26.4 VAC
Inrush current
(peak value)
Time
10 ms
H3CR-F
0.7 A
26.4 VDC
13.2 VDC
137.5 VDC
132 VAC
264 VAC
26.4 VAC
26.4 VDC
52.8 VDC
137.5 VDC
132 VAC
264 VAC
26.4 VAC
26.4 VDC
52.8 VDC
137.5 VDC
1.1 A
9.4 ms
3.3 ms
9.1 ms
111 ms
119 ms
133 ms
137 ms
112 ms
109 ms
364 ms
323 ms
478 ms
560 ms
384 ms
380 ms
12 VDC
52 mA
0.40 A
1.05 A
1.07 A
1.26 A
0.85 A
0.73 A
0.62 A
1.02 A
1.03 A
1.21 A
0.87 A
0.71 A
0.62 A
48 to 125 VDC
100/110/120 VAC
200/220/240 VAC
24 VAC/DC
H3CR-H
S-series
48 VDC
100 to 125 VDC
100/110/120 VAC
200/220/240 VAC
24 VAC/DC
M-series
48 VDC
100 to 125 VDC
Note: 1. The above figures are all approximations and should be used for reference only.
2. The inrush current is given mainly for DC models for the required power supply design specifications. For the H3CR-H, the inrush
current is also given for 100/110/120-VAC and 200/220/240-VAC models because these models have higher inrush currents than
other series.
12
H3CR-F
H3CR-F
Input/Output (H3CR-H)
AnappropriateinputisappliedtotheinputsignalterminaloftheTim-
er when the input terminal for the input signal is short-circuited. Do
not attempt to connect any input terminal to any terminal other than
the input terminal or to apply voltage across other than the specified
inputterminals or the internal circuits of the Timermaybedamaged.
Input contact
Power supply
AC or DC
H3CR
Input
terminal
*
L
*Do not connect a relay or any other load between these two
points, otherwise the internal circuit of the Timer may be
damaged due to the high-tension voltage applied to the input
terminals.
When connecting a relay or a transistor as an external signal input
device, pay attention to the following points to prevent short-circuit-
ing due to a sneak current to the transformerless power supply.
If a relay or transistor is connected to two or more Timers, the input
terminalsofthoseTimersmustbewiredproperlysothattheywillnot
be different in phase or the terminals will be short-circuited to one
another (refer to the figures below).
H3CR series timer
Contact or transistor for
external input signal
Input
Power supply
terminal
Incorrect
Short-circuit
current
Input
terminal
Input
terminal
Power supply
Correct
Input
terminal
Environment
WhenusingtheTimerinanareawithexcesselectronicnoise, sepa-
rate the Timer, wiring, and the equipment which generates the input
signals as far as possible from the noise sources. It is also recom-
mended to shield the input signal wiring to prevent electronic inter-
ference.
Organic solvents (such as paint thinner), as well as very acidic or
basic solutions can damage the outer casing of the Timer.
Others
If the Timer is mounted on a control board, dismount the timer from
the control board or short-circuit the circuitry of the power board be-
fore carrying out a voltage withstand test between the electric cir-
cuitry and non current-carrying metal part of the Timer, in order to
prevent the internal circuitry of the Timer from damage.
13
相关型号：
©2020 ICPDF网 联系我们和版权申明