KAF-0402-ABA-CD-B2 [ONSEMI]
FULL FRAME CCD IMAGE SENSOR;型号: | KAF-0402-ABA-CD-B2 |
厂家: | ONSEMI |
描述: | FULL FRAME CCD IMAGE SENSOR CD |
文件: | 总16页 (文件大小:191K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
KAF-0402
768 (H) x 512 (V) Full Frame
CCD Image Sensor
Description
The KAF−0402 Image Sensor is a high performance area CCD
(charge-coupled device) image sensor with 768 (H) × 512 (V)
photoactive pixels designed for a wide range of image sensing
applications.
www.onsemi.com
The sensor incorporates true two-phase CCD technology,
simplifying the support circuits required to drive the sensor as well as
reducing dark current without compromising charge capacity.
The sensor also utilizes the TRUESENSE Transparent Gate Electrode
to improve sensitivity compared to the use of a standard front side
illuminated polysilicon electrode.
Optional microlenses focus the majority of the light through the
transparent gate, increasing the optical response further.
Table 1. GENERAL SPECIFICATIONS
Parameter
Typical Value
Figure 1. KAF−0402 Full Frame CCD
Image Sensor
Architecture
Full Frame CCD, Enhanced
Response
Total Number of Pixels
Number of Active Pixels
Pixel Size
784 (H) × 520 (V)
Applications
768 (H) × 512 (V) = approx. 0.4 Mp
9.0 mm (H) × 9.0 mm (V)
• Digitization
• Medical
• Scientific
Active Image Size
6.91 mm (H) × 4.6 mm (V)
8.3 mm (Diagonal)
1/2″ Optical Format
ORDERING INFORMATION
See detailed ordering and shipping information on page 2 of
this data sheet.
Die Size
8.4 mm (H) × 5.5 mm (V)
3:2
Aspect Ratio
Saturation Signal
100,000 electrons
Quantum Efficiency
(with Microlens)
Peak:
400 nm: 45%
77%
Quantum Efficiency
(No Microlens)
Peak: 65%
400 nm: 30%
−
Output Sensitivity
Read Noise
10 mV/e
15 electrons
2
Dark Current
< 10 pA/cm at 25°C
Dark Current Doubling Temperature
Dynamic Range
6.3°C
76 dB
Charge Transfer Efficiency
Blooming Suppression
Maximum Date Rate
Package
> 0.99999
None
10 MHz
CERDIP Package (Sidebrazed)
Clear or AR Coated, 2 Sides
Cover Glass
NOTE: Parameters above are specified at T = 25°C unless otherwise noted.
© Semiconductor Components Industries, LLC, 2015
1
Publication Order Number:
April, 2015 − Rev. 2
KAF−0402/D
KAF−0402
ORDERING INFORMATION
Table 2. ORDERING INFORMATION − KAF−0402 IMAGE SENSOR
Part Number
Description
Marking Code
KAF−0402−AAA−CB−B1
Monochrome, No Microlens, CERDIP Package (Sidebrazed),
Clear Cover Glass (No Coatings), Grade 1
KAF−0402−AAA−CB−AE
KAF−0402−AAA−CP−B1
KAF−0402−AAA−CP−B2
KAF−0402−AAA−CP−AE
KAF−0402−ABA−CD−B1
KAF−0402−ABA−CD−B2
KAF−0402−ABA−CD−AE
KAF−0402−ABA−CP−B1
KAF−0402−ABA−CP−B2
KAF−0402−ABA−CP−AE
Monochrome, No Microlens, CERDIP Package (Sidebrazed),
Clear Cover Glass (No Coatings), Engineering Sample
Monochrome, No Microlens, CERDIP Package (Sidebrazed),
Taped Clear Cover Glass (No Coatings), Grade 1
KAF−0402−AAA
Serial Number
Monochrome, No Microlens, CERDIP Package (Sidebrazed),
Taped Clear Cover Glass (No Coatings), Grade 2
Monochrome, No Microlens, CERDIP Package (Sidebrazed),
Taped Clear Cover Glass (No Coatings), Engineering Sample
Monochrome, Telecentric Microlens, CERDIP Package (Sidebrazed),
Clear Cover Glass with AR Coating (Both Sides), Grade 1
Monochrome, Telecentric Microlens, CERDIP Package (Sidebrazed),
Clear Cover Glass with AR Coating (Both Sides), Grade 2
Monochrome, Telecentric Microlens, CERDIP Package (Sidebrazed),
Clear Cover Glass with AR Coating (Both Sides), Engineering Sample
KAF−0402−ABA
Serial Number
Monochrome, Telecentric Microlens, CERDIP Package (Sidebrazed),
Taped Clear Cover Glass (No Coatings), Grade 1
Monochrome, Telecentric Microlens, CERDIP Package (Sidebrazed),
Taped Clear Cover Glass (No Coatings), Grade 2
Monochrome, Telecentric Microlens, CERDIP Package (Sidebrazed),
Taped Clear Cover Glass (No Coatings), Engineering Sample
Table 3. ORDERING INFORMATION − EVALUATION SUPPORT
Part Number
Description
KAF−0402−12−5−A−EVK
Evaluation Board (Complete Kit)
See the ON Semiconductor Device Nomenclature document (TND310/D) for a full description of the naming convention
used for image sensors. For reference documentation, including information on evaluation kits, please visit our web site at
www.onsemi.com.
www.onsemi.com
2
KAF−0402
DEVICE DESCRIPTION
Architecture
4 Dark Lines
fV1
fV2
KAF−0402
Usable Active Image Area
768 (H) × 512 (V)
GUARD
9 × 9 mm Pixels
3:2 Aspect Ratio
V
RD
fR
4 Dark Lines
fH1
V
DD
V
OUT
768 Active Pixels/Line
fH2
V
4 Dark
12 Dark
SS
10 Inactive
2 Inactive
SUB
V
OG
Figure 2. Block Diagram
The sensor consists of 784 parallel (vertical) CCD shift
registers each 520 elements long. These registers act as both
the photosensitive elements and as the transport circuits that
allow the image to be sequentially read out of the sensor.
The parallel (vertical) CCD registers transfer the image one
line at a time into a single 796-element (horizontal) CCD
shift register. The horizontal register transfers the charge to
a single output amplifier. The output amplifier is a two-stage
source follower that converts the photo-generated charge to
a voltage for each pixel.
Microlenses
Microlenses are formed along each row. They are
effectively half of a cylinder centered on the transparent
gates, extending continuously in the row direction. They act
to direct the photons away from the polysilicon gate and
through the transparent gate. This increases the response,
especially at the shorter wavelengths (< 600 nm).
Microlens
V1
V2
Silicon
Figure 3. Microlens
www.onsemi.com
3
KAF−0402
H1
H2
H1
H2
HCCD
Charge
Transfer
V
DD
V
OG
R
V
RD
Floating
Diffusion
V
OUT
Source
Follower
#1
Source
Follower
#2
Figure 4. Output Schematic
Output Structure
false signal depending on operating conditions. There are
two more dummy pixels at the end of each line.
Charge presented to the floating diffusion is converted
into a voltage and current amplified in order to drive off-chip
loads. The resulting voltage change seen at the output is
linearly related to the amount of charge placed on the
floating diffusion. Once the signal has been sampled by the
system electronics, the reset gate (fR) is clocked to remove
the signal and the floating diffusion is reset to the potential
applied by Vrd (see Figure 4). More signal at the floating
diffusion reduces the voltage seen at the output pin. In order
to activate the output structure, an off-chip load must be
added to the Vout pin of the device such as shown in
Figure 8.
Image Acquisition
An electronic representation of an image is formed when
incident photons falling on the sensor plane create
electron-hole pairs within the sensor. These photon induced
electrons are collected locally by the formation of potential
wells at each photogate or pixel site. The number of
electrons collected is linearly dependent on light level and
exposure time and non-linearly dependent on wavelength.
When the pixel’s capacity is reached, excess electrons will
leak into the adjacent pixels within the same column. This
is termed blooming. During the integration period, the fV1
and fV2 register clocks are held at a constant (low) level.
See Figure 9.
Dark Reference Pixels
There are 4 light shielded pixels at the beginning of each
line, and 12 at the end. There are 4 dark lines at the start of
every frame and 4 dark lines at the end of each frame. Under
normal circumstances, these pixels do not respond to light.
However, dark reference pixels in close proximity to an
active pixel can scavenge signal depending on light intensity
and wavelength and therefore will not represent the true dark
signal.
Charge Transport
Referring again to Figure 10, the integrated charge from
each photogate is transported to the output using a two-step
process. Each line (row) of charge is first transported from
the vertical CCD to the horizontal CCD register using the
fV1 and fV2 register clocks. The horizontal CCD is
presented a new line on the falling edge of fV2 while fH1
is held high. The horizontal CCD then transports each line,
pixel by pixel, to the output structure by alternately clocking
the fH1 and fH2 pins in a complementary fashion. On each
falling edge of fH2 a new charge packet is transferred onto
a floating diffusion and sensed by the output amplifier.
Dummy Pixels
Within the horizontal shift register are 10 leading
additional pixels that are not associated with a column of
pixels within the vertical register. These pixels contain only
horizontal shift register dark current signal and do not
respond to light. A few leading dummy pixels may scavenge
www.onsemi.com
4
KAF−0402
Physical Description
Pin Description and Device Orientation
VOG
VOUT
VDD
VRD
fR
1
2
3
4
5
6
7
8
9
24 N/C
23 GUARD
22 fV1
21 fV1
20 fV2
19 fV2
18 fV2
17 fV2
16 fV1
15 fV1
14 VSUB
13 N/C
Pin 1
Pixel 1,1
VSS
fH1
fH2
N/C
N/C 10
VSUB 11
N/C 12
Figure 5. Pinout Diagram
Table 4. PIN DESCRIPTION
Pin
13
14
15
16
17
18
19
20
21
22
23
24
Name
Description
Pin
1
Name
VOG
VOUT
VDD
VRD
fR
Description
N/C
VSUB
fV1
No Connection
Output Gate
Video Output
Substrate
2
Vertical CCD Clock − Phase 1
Vertical CCD Clock − Phase 1
Vertical CCD Clock − Phase 2
Vertical CCD Clock − Phase 2
Vertical CCD Clock − Phase 2
Vertical CCD Clock − Phase 2
Vertical CCD Clock − Phase 1
Vertical CCD Clock − Phase 1
Guard Ring
3
Amplifier Supply
Reset Drain
fV1
4
fV2
5
Reset Clock
fV2
6
VSS
fH1
fH2
N/C
Amplifier Supply Return
fV2
7
Horizontal CCD Clock − Phase 1
Horizontal CCD Clock − Phase 2
No Connection
fV2
8
fV1
9
fV1
10
11
12
N/C
No Connection
GUARD
N/C
VSUB
N/C
Substrate
No Connection
No Connection
www.onsemi.com
5
KAF−0402
IMAGING PERFORMANCE
Specifications
Electro-Optical
All values measured at 25°C and nominal operating conditions. These parameters exclude defective pixels.
Table 5. SPECIFICATIONS
Description
Symbol
Min.
Nom.
Max.
Units
Notes
Verification Plan
−
9
Saturation Signal
N
e /pix
1
Design
SAT
Vertical CCD Capacity
Horizontal CCD Capacity
Output Node Capacity
85,000
170,000
190,000
100,000
200,000
220,000
−
240,000
−
9
Quantum Efficiency
(see Figure 6)
−
−
−
Design
Photoresponse Non-Linearity
Photoresponse Non-Uniformity
Dark Signal
PRNL
PRNU
−
−
1.0
0.8
2.0
−
%
%
2
3
4
8
Die
−
8
J
−
−
15
6
30
10
e /pix/sec
pA/cm
Die
DARK
2
9
Dark Signal Doubling
Temperature
−
6.3
7
°C
Design
−
8
Dark Signal Non-Uniformity
Dynamic Range
DSNU
DR
−
72
15
76
30
−
e /pix/sec
5
6
Die
9
dB
Design
8
Charge Transfer Efficiency
Output Amplifier DC Offset
Output Amplifier Sensitivity
CTE
0.99997
0.99999
−
Die
9
V
ODC
V
RD
V
RD
+ 0.5
V + 1.0
RD
V
Design
−
9
V
/N −
OUT
9
10
−
mV/e
Design
e
9
Output Amplifier Output
Impedance
Z
OUT
180
200
220
W
Design
Noise Floor
n −
−
15
20
electrons
7
e
1. For pixel binning applications, electron capacity up to 330,000 can be achieved with modified CCD inputs.
2. Worst case deviation from straight line fit, between 2% and 90% of V
.
SAT
3. One Sigma deviation of a 128 × 128 sample when CCD illuminated uniformly at half of saturation.
4. Average of all pixels with no illumination at 25°C.
5. Average dark signal of any of 11 × 8 blocks within the sensor (each block is 128 × 128 pixels).
6. 20LOG (N
/ n −) at nominal operating frequency and 25°C.
e
SAT
7. Noise floor is specified at the nominal pixel frequency and excludes any dark or pattern noises. It is dominated by the output amplifier power
spectrum with a bandwidth = 5 ⋅ pixel rate.
8. A parameter that is measured on every sensor during production testing.
9. A parameter that is quantified during the design verification activity.
www.onsemi.com
6
KAF−0402
TYPICAL PERFORMANCE CURVES
KAF−0402 Spectral Response
1
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
KAF−0402 (with microlenses)
KAF−0402 (no microlenses)
400
500
600
700
800
900
1000
Wavelength (nm)
Figure 6. Typical Spectral Response
www.onsemi.com
7
KAF−0402
DEFECT DEFINITIONS
Table 6. SPECIFICATIONS (Defect tests performed at T = 25°C)
Grade
C1
Point Defect
< 5
Cluster Defect
Column Defect
0
0
0
C2
< 10
< 4
Point Defects
A column containing a pixel with dark current
> 12,000 e /pix/sec at 25°C (Bright column).
−
Dark: A pixel which deviates by more than 6% from
neighboring pixels when illuminated to 70% of saturation.
A column that does not meet the minimum vertical CCD
charge capacity (Low charge capacity column).
−
Bright: A pixel whose dark current > 5,000 e /pix/sec at
25°C.
−
−
A column that loses > 250 e under 2 ke (Trap defect).
Cluster Defect
A grouping of not more than 5 adjacent point defects.
Neighboring Pixels
The surrounding 128 × 128 pixels or 64 columns/rows.
Column Defect
A grouping of > 5 contiguous point defects along a single
column.
Defect Separation
Column and cluster defects are separated by no less than
2 pixels in any direction (excluding single pixel defects).
1, 512
768, 512
1, 1
768, 1
Figure 7. Active Pixel Region
www.onsemi.com
8
KAF−0402
OPERATION
Table 7. ABSOLUTE MAXIMUM RATINGS
Description
Diode Pin Voltages
Symbol
Minimum
Maximum
Units
V
Notes
1, 2
1, 3, 5
4
V
DIODE
V
GATE1
0
−16
−
20
16
Gate Pin Voltages
V
Output Bias Current
Output Load Capacitance
I
−10
15
mA
pF
OUT
C
−
4
LOAD
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. Referenced to pin VSUB or between each pin in this group.
2. Includes pins: VRD, VDD, VSS, VOUT.
3. Includes pins: fV1, fV2, fH1, fH2, VOG, VLG, fR.
4. Avoid shorting output pins to ground or any low impedance source during operation.
5. This sensor contains gate protection circuits to provide some protection against ESD events. The circuits will turn on when greater than 16 V
appears between any two gate pins. Permanent damage can result if excessive current is allowed to flow under these conditions.
Table 8. DC BIAS OPERATING CONDITIONS
Maximum DC
Current (mA)
Description
Symbol
Minimum
Nominal
Maximum
Units
Notes
Reset Drain
V
10
1.5
14.75
0
11.0
2.0
15
0
11.5
2.5
15.5
0
V
0.01
RD
Output Amplifier Return
Output Amplifier Supply
Substrate
V
V
−0.5
SS
DD
V
V
I
OUT
V
SUB
V
0.01
0.01
0.01
−
Output Gate
V
OG
3.75
8.0
−
4
5
V
Guard Ring
GUARD
9.0
−5
12.0
−10
V
Video Output Current
I
mA
1
OUT
1. An output load sink must be applied to V
to activate output amplifier − see Figure 8.
OUT
+15 V
0.1 mF
~5ma
V
OUT
2N3904 or Equivalent
Buffered Output
140 W
1 kW
Figure 8. Example Output Structure Load Diagram
www.onsemi.com
9
KAF−0402
AC Operating Conditions
Table 9. CLOCK LEVELS
Effective
Capacitance
Description
Symbol
fV1
fV1
fV2
fV2
fH1
fH1
fH2
fH2
fR
Level
Low
Minimum
−10.5
−0.5
−10.5
−0.5
−4.5
9.5
Nominal
−10
Maximum
−9.5
1.0
Units
V
Vertical CCD Clock − Phase 1
Vertical CCD Clock − Phase 1
Vertical CCD Clock − Phase 2
Vertical CCD Clock − Phase 2
Horizontal CCD Clock − Phase 1
Horizontal CCD Clock − Phase 1
Horizontal CCD Clock − Phase 2
Horizontal CCD Clock − Phase 2
Reset Clock
6 nF (All fV1 Pins)
6 nF (All fV1 Pins)
6 nF (All fV2 Pins)
6 nF (All fV2 Pins)
50 pF
High
0
V
Low
−10.0
0
−9.5
1.0
V
High
V
Low
−4.0
10.0
−4.0
10.0
−2.0
6.0
−3.5
10.5
−3.5
10.5
−1.75
7.0
V
Amplitude
Low
V
50 pF
−4.5
9.5
V
50 pF
Amplitude
Low
V
50 pF
−3.0
5.0
V
5 pF
Reset Clock
fR
Amplitude
V
5 pF
1. All pins draw less than 10 mA DC current.
2. Capacitance values relative to V
.
SUB
www.onsemi.com
10
KAF−0402
TIMING
Table 10. REQUIREMENTS AND CHARACTERISTICS
Description
fH1, fH2 Clock Frequency
Pixel Period (1 Count)
fH1, fH2 Set-up Time
fV1, fV2 Clock Pulse Width
Reset Clock Pulse Width
Readout Time
Symbol
Minimum
−
Nominal
Maximum
Units
MHz
ns
Notes
f
H
4
250
1
10
−
1, 2, 3
t
100
0.5
PIX
t
f
−
ms
HS
t
1.5
2
−
ms
2
4
5
6
7
f
V
R
t
f
10
20
107
−
−
ns
t
43.7
−
−
ms
READOUT
Integration Time
t
−
INT
Line Time
t
84.1
206
−
ms
LINE
1. 50% duty cycle values.
2. CTE may degrade above the nominal frequency.
3. Rise and fall times (10/90% levels) should be limited to 5−10% of clock period. Crossover of register clocks should be between 40−60% of
amplitude.
4. fR should be clocked continuously.
5. t
= (520 ⋅ t
)
READOUT
LINE
6. Integration time (t ) is user specified. Longer integration times will degrade noise performance due to dark signal fixed pattern and shot
INT
noise.
7. t
= (3 ⋅ t ) + t
+ (796 ⋅ t ) + t
HS PIX PIX
f
f
LINE
V
Frame Timing
Frame Timing
t
t
READOUT
INT
1 Frame = 520 Lines
fV1
fV2
Line
1
2
519
520
fH1
fH2
Figure 9. Frame Timing Diagram
www.onsemi.com
11
KAF−0402
Line Timing and Pixel Timing
Line Timing Detail
Pixel Timing Detail
1 Line = 796 Pixels
t
f
R
t
f
V
fR
fV1
fV2
t
f
V
fH1
t
PIX
1 Count
t
f
t
PIX
HS
fH2
fH1
fH2
V
PIX
V
OUT
796 Counts
V
SAT
V
DARK
V
ODC
fR
V
SUB
Line Content
V
SAT
Saturated pixel video output signal
V
DARK
Video output signal in no-light situation,
not zero due to J
Pixel video output signal level,
more electrons = more negative
Video level offset with respect to V
Analog ground
1−10 11−14
15−782
783−794 795−796
Dummy Pixels
DARK
V
PIX
V
ODC
V
SUB
*
SUB
Photoactive
Dark Reference
* See Image Acquisition section.
Figure 10. Line and Pixel Timing Diagrams
www.onsemi.com
12
KAF−0402
STORAGE AND HANDLING
Table 11. STORAGE CONDITIONS
Description
Symbol
Minimum
Maximum
100
Units
°C
Notes
Storage Temperature
Humidity
T
ST
−
5
RH
90
%
1
1. T = 25°C. Excessive humidity will degrade MTTF.
For information on ESD and cover glass care and
cleanliness, please download the Image Sensor Handling
and Best Practices Application Note (AN52561/D) from
www.onsemi.com.
For quality and reliability information, please download
the Quality & Reliability Handbook (HBD851/D) from
www.onsemi.com.
For information on device numbering and ordering codes,
please download the Device Nomenclature technical note
(TND310/D) from www.onsemi.com.
For information on soldering recommendations, please
download the Soldering and Mounting Techniques
Reference
www.onsemi.com.
Manual
(SOLDERRM/D)
from
For information on Standard terms and Conditions of
Sale, please download Terms and Conditions from
www.onsemi.com.
www.onsemi.com
13
KAF−0402
MECHANICAL INFORMATION
Completed Assembly
Figure 11. Completed Assembly (1 of 2)
www.onsemi.com
14
KAF−0402
Figure 12. Completed Assembly (2 of 2)
www.onsemi.com
15
KAF−0402
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
For additional information, please contact your local
Sales Representative
KAF−0402/D
相关型号:
©2020 ICPDF网 联系我们和版权申明